Commit Graph

6 Commits

Author SHA1 Message Date
Sungbo Eo
ab78694fe8 treewide: rename POWER_ON_STRIP register
AR8327 datasheet[1] calls the register at address 0x0010
"Power-on Strapping Register". As it has nothing to do with "strip",
let's rename it to "POWER_ON_STRAP" to make it easier to grasp.

[1] https://lafibre.info/images/doc/201106_spec_AR8327.pdf

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-25 21:50:50 +02:00
Adrian Schmutzler
635f111148 ath79: drop and consolidate redundant chosen/bootargs
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.

The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi

Note that while this tidies up master a lot, it might develop into a
frequent pitfall for backports.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-25 23:09:05 +02:00
Sebastian Schaper
64d088d8f9 ath79: increase spi clock for D-Link DIR-842
AHB is 258 MHz for this device (CPU_PLL / 3), but there is no difference
between 64 MHz and 50 MHz for spi-max-frequency, thus increase to 50 MHz.

Tested on revisions C1 and C3.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2020-05-26 22:49:18 +02:00
Sebastian Schaper
8643c0b53d ath79: define switch reset-gpios for D-Link DIR-842
GPIO 11 needs to be pulled high for the external gigabit switch to work,
this is currently solved via gpio-hog. Replace with phy0 reset-gpios.

Tested on revisions C1 and C3. Reset button is still working for reboot,
to enter failsafe, and to enter bootloader http recovery.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2020-05-26 22:49:18 +02:00
Adrian Schmutzler
231dc26867 treewide: remove dts-v1 identifier from DTSI files
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.

This removes the identifier from all DTSI files in /target/linux.

Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx

This does not touch ipq806x for now, as the bump to 4.19 is close.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 16:44:06 +01:00
Jackson Lim
030fc6ab6c ath79: add support for D-Link DIR-842 C1
Hardware spec of DIR-842 C1:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: circuit onboard, but components are not soldered

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or
   the u-boot failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted.
   Otherwise the u-boot will enter failsafe mode as the checksum
   of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the
   firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
   just upgrade the factory.bin through the u-boot failsafe interface
   and then goto step 2.

Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
[fix whitespace issues]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-05 10:54:11 +02:00