MAC-addresses are stored with colons, thus they can now be referenced
using NVMEM.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16310
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream commit 9ba0cae3cac07c21c583f9ff194f74043f90d29c made FSL_IFC
visible and selectable, which means that in order for MTD_NAND_FSL_IFC
to work, it needs these two extra CONFIG options.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16717
Signed-off-by: Robert Marko <robimarko@gmail.com>
In #16396, crashes were reported on MT7620, which were introduced by enabling
CONFIG_LIST_HARDENED. The cause seems to be random memory corruption somewhere
in the kernel. Unfortunately the crash traces do not point to the real cause
of the crash in any way.
Since MT7620 is really ancient hardware that likely only has few users left,
I don't expect that anybody will invest a significant amount of time to track
down the real cause. Because of that, let's disable CONFIG_LIST_HARDENED on
this target only, and leave it enabled on all other platforms.
Fixes: #16396
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add preinit script to rename network interfaces according to the
label provided in Device Tree.
Fixes: b6d8297510 ("mediatek: mt7622: add Adtran SmartRG SDG-841t6 device")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Two patches declared as accepted in v6.13 were already accepted for
v6.12. Fix filenames and order of patches applied.
Reported-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Fixes: 8cc049cec2 ("generic: phy: aquantia: move accepted patches to backport-6.6")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This driver allows retrieving MAC addresses and other factory information
via the NVMEM framework on Adtran devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Building HWMON as module prevents some other drivers from getting built
into the kernel, e.g. mxl-gpy. Always enable HWMON and also set
THERMAL_HWMON.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport newly introduced support for 'active-high' property and use
it to correctly implement polarity assignment for Aquantia PHY LEDs.
Previously the 'active-low' property was used to switch a LED PIN to
active-high ("drive VDD" in Aquantia-speak) mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Only add SerDes interface modes at lower speeds to host_interfaces.
Fixes: 5281033831 ("generic: net: phy: use all SerDes MAC interface modes")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The snapshot builds for qoriq only contain ext4 images. Add squashfs to
FEATURES to also have the buildbots build squashfs images.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Dropping the source-only flag from qoriq and adding it to the buildbots
exposed a missing kernel config symbol: CONFIG_DRM_OFDRM. Addd it as
disabled to the qoriq kernel config, as the only device currently
supported in the qoriq target does not have any display hardware.
Reported-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The blamed commit adds a upgrade recipe for nas1dual to specify the
firmware partition name, but does not actually include the recipe that
will be called.
Since it previously relied on the default one, add that one.
Fixes: d21720fa90 ("mvebu: fix default partition name")
Link: https://github.com/openwrt/openwrt/pull/16704
Signed-off-by: Robert Marko <robimarko@gmail.com>
While the qoriq target currently supports only one device, the
WatchGuard Firebox M300, the feedback from people using it is that it's
a great bang for the buck. Additionally, people suggest having no
snapshots available hurts adoption.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The firmware partition name is specifc to ipTIME NAS1dual and should not be
set globally.
Fixes: #16148
Fixes: 6ff970bb51 ("mvebu: add support for ipTIME NAS1dual")
Signed-off-by: Boris Krasnovskiy <borkra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16690
Signed-off-by: Robert Marko <robimarko@gmail.com>
73a9f9f857 added support. Let's use it.
Calibration data is not yet supported.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16256
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Beside the already existing control of the
Blue cover LED, this will also add the
Green and the Red cover LEDS available in the
Asus TUF-AX6000.
Signed-off-by: Magnus Sandin <magnus.sandin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16632
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This solution that is needed for some routers to provide proper
LED activity when controlled directly by the MV88E6xxx switch,
has just been merged in upstream Linux.
Make this patch 901 as other backports from earlier kernels
are in patch 896 and this is the first free number after
that.
Patch offsets in pending patches are augmented as part of
the refresh.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI driver framework can handle it automatically in
spi.c:spi_setup():spi_set_cs():gpiod_set_value_cansleep().
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16636
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ase subtarget supports two devices. ALLNET ALL0333CJ has one
Ethernet port and uses only the built-in MAC and PHY. The second
device is the Netgear DGN1000, which uses an AR8216 switch.
The driver for the adm6996 switch was probably accidentally
enabled instead of the ar8216 in commit that restores ase support
9b321bc60d ("lantiq: add Amazon-SE subtarget").
Before removing the ase subtarget, only ar8216 was enabled
c821836395 ("lantiq: remove unmaintained code").
Reduce uncompressed kernel size by 15.6 kB.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15332
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This was done by executing these command:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/15332
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport BLOCK OF support patch merged upstream and refresh pending
BLOCK patches.
This is a new way to declare partition table for BLOCK device (eMMC
currently supported) with the use of DTS.
Current pending patch are adapted to not cause regression with current
downstream implementation of a similar functionality.
Also enable the new OF_PARTITION config by default.
Link: https://github.com/openwrt/openwrt/pull/16663
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The bootloader can support zImage linux kernel which can decrease
the firmware image size.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16662
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of forcing 2.5G PHYs into rate-adapter mode which results higher
energy consumption, lack of support for half-duplex modes and typically
worse performance when linked at speeds less than 2.5G, use SGMII mode
which allows the MAC to follow the PHY speed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Follow the advise of Russell King allows to greatly improve the driver
for RealTek's 1G and 2.5G Ethernet PHYs. The results are full/half
duplex as well as Gbit master/slave property being read from PHY
Specific Status Register (PHYSR), and fixes regarding link-partner
advertisement.
Fixes: #14504
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The previous iteration of MediaTek's PHY patches caused various weird bugs.
Drop culprit patch 733-10-net-phy-mediatek-Extend-1G-TX-RX-link-pulse-time.patch
and use the most recent iteration of the patchset which has been posted to the
netdev mailing list.
Link: https://patchwork.kernel.org/project/netdevbpf/list/?series=895513&state=*
Fixes: #16448
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
mutex_destroy is not called in any error paths or in _remove. Just use
devm to do so.
Removed a pointless platform_set_devdata call. Not needed with all of
the devm conversions.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16630
Signed-off-by: Robert Marko <robimarko@gmail.com>
Also use devm for gpiochip_add_data.
Allows completely removing the _remove function.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16622
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification
-------------
- SoC : Qualcomm IPQ4019
- RAM : 256 MiB DDR3 (NT5CC128M16JR-EK)
- Flash : 64 MiB SPI NOR (Winbond W25Q512JVFQ)
- WLAN : IPQ4019 built-in
- 2.4 GHz : 2x2 MIMO WiFi4
- 5 GHz : 2x2 MIMO WiFi5
- Ethernet : QCA8075 10/100/1000 Mbps 1x WAN (ETH1, PoE); 1x LAN (ETH2)
- USB : 1x 2.0 Type-A
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
- LEDs : 1x RUN (lime & red)
1x WiFi 2.4 GHz (lime)
1x WiFi 5 GHz (lime)
2x ETH (lime), controlled by the QCA8075 phy
- Power : DC 12V & 802.3at PoE
- FCC ID : 2AHKT-WIA3300-20
- TFTP IP :
- client : 192.168.18.254
- router : 192.168.18.1
Installation
------------
1. Open uart console and start TFTP server. Copy initramfs image to
the TFTP root directory and rename it to 'ipqinitramfs.bin'.
2. Power on and press 'Enter' to exit to the u-boot console according
to the TTL log prompt.
3. Execute commands to load the initramfs image:
tftpboot && bootm
4. Enter into OpenWrt to backup the partitions if you want to restore
the stock firmware one day.
5. Override default 'bootcmd' environment variable in u-boot console:
env set bootcmd 'sf probe && sf read $loadaddr 0x980000 0x800000 && bootm $loadaddr'
env save
6. Repeat step 3 and flash 'sysupgrade' image in OpenWrt.
Recovery and return to stock
----------------------------
1. Restore the backup firmware partitions in the installation step 4.
2. Restore `bootcmd` environment variable via commands:
env set bootcmd bootipq && env save
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LABEL | xx:xx:xx:xx:xx:25 |
| LAN | xx:xx:xx:xx:xx:26 |
| WAN | xx:xx:xx:xx:xx:25 |
| WLAN 2g | xx:xx:xx:xx:xx:28 |
| WLAN 5g | xx:xx:xx:xx:xx:29 |
+---------+-------------------+
Notice
-----------
1. Some CH340 USB-TTL module doesn't work on this device.
2. The 'firmware' partition consists of four parts in the vendor
layout:
* Name Start Size
* rootfs 0x980000 0x1680000
* 0:HLOS1 0x2000000 0x800000
* rootfs_1 0x2800000 0x1400000
* rootfs_data 0x3c00000 0x350000
3. User can control the USB power supply via commands:
echo enabled > /sys/devices/platform/output-usb-power/state
echo disabled > /sys/devices/platform/output-usb-power/state
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16476
Signed-off-by: Robert Marko <robimarko@gmail.com>
It can be used to control the power on/off status for the fixed
voltage regulator via sysfs.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16476
Signed-off-by: Robert Marko <robimarko@gmail.com>
Even though optional is used, there's are still pointless NULL
assignments.
Use dev_err_probe to avoid manually handling EPROBE_DEFER.
Use devm_platform_iomap_resource. No struct resource needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Shiji Yang <yangshiji66@qq.com> on NETGEAR R6100.
Link: https://github.com/openwrt/openwrt/pull/16519
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
...conversion.
Commit 20736013e9 ("kernel: backport nvmem v6.6 fixes and v6.7 changes")
has causedt he device to no longer correctly read MAC address from its
onboard 24c64 EEPROM, because "at24" driver doesn't support legacy
nvmem-cell bindings [1] - and there was an explicit config option added
to mandate that behaviour in the following patch:
820-v6.7-0002-nvmem-add-explicit-config-option-to-read-old-syntax-.patch
But some of the devices, MR33 and MR74 included, weren't converted with
that as well.
Convert the definition to use proper fixed-layout binding to fix it.
The offending change was introduced between v23.05.0 and v23.05.1, and
found by bisection:
git bisect start
# status: waiting for both good and bad commits
# good: [bd4f415efa] OpenWrt v23.05.0: adjust config defaults
git bisect good bd4f415efa
# status: waiting for bad commit, 1 good commit known
# bad: [a58a86693f] OpenWrt v23.05.1: adjust config defaults
git bisect bad a58a86693f
# good: [3d0a78add2] qualcommax: only build initramfs if CONFIG_TARGET_ROOTFS_INITRAMFS is set
git bisect good 3d0a78add2
# bad: [21e5db97c4] build: add CycloneDX SBOM JSON support
git bisect bad 21e5db97c4
# good: [89184b15cf] mediatek: add build for MT7981 RFB
git bisect good 89184b15cf
# bad: [41f27bbb6d] bcm53xx: add the latest fix version of brcm_nvram
git bisect bad 41f27bbb6d
# good: [b649b0bf71] kernel: nvmem: fix "fixed-layout" & support "mac-base"
git bisect good b649b0bf71
# bad: [20736013e9] kernel: backport nvmem v6.6 fixes and v6.7 changes
git bisect bad 20736013e9
# good: [066971615f] kernel: backport v6.6 nvmem changes
git bisect good 066971615f
# first bad commit: [20736013e9] kernel: backport nvmem v6.6 fixes and v6.7 changes
Link: [1] https://github.com/openwrt/openwrt/issues/15393#issuecomment-2212300849
Fixes: 20736013e9 ("kernel: backport nvmem v6.6 fixes and v6.7 changes")
Fixes: https://github.com/openwrt/openwrt/issues/15393
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16623
Signed-off-by: Robert Marko <robimarko@gmail.com>
Avoids needing to call mutex_destroy in error paths, which is missing
anyway.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16620
Signed-off-by: Robert Marko <robimarko@gmail.com>
The u-boot,env driver does not have layout in compatible.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16616
Signed-off-by: Robert Marko <robimarko@gmail.com>
