Commit Graph

25579 Commits

Author SHA1 Message Date
Josef Schlehofer
9d530ac4bf mvebu: kernel: enable CONFIG_BLK_DEV_NVME
CONFIG_BLK_DEV_NVME [1]:
- This is a kernel driver for SSD connected to PCI or PCIe bus [1].
By default, it is enabled for targets "ipq807x", "rockchip/armv8"
and "x86/64".

With miniPCIe adapter, there is a possibility to connect NVMe disk
to Turris Omnia (cortex-a9), Turris MOX (cortex-a53).

It allows to boot system from NVMe disk, because of that it can not
be kmod package as you can not access the disk to be able to boot from
it.

CONFIG_NVME_CORE [2]:
- This is selected by CONFIG_BLK_DEV_NVME
It does not need to be explicitly enabled, but it is done for "ipq807",
"x64_64" and rockchip/armv8", which has also enabled the previous config
option as well.

Kernel increase: ~28k KiB on mamba kernel

Reference:
[1] https://cateee.net/lkddb/web-lkddb/BLK_DEV_NVME.html
[2] https://cateee.net/lkddb/web-lkddb/NVME_CORE.html

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-01-15 17:26:55 +01:00
Christian Lamparter
cfc13c4459 ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data
moves extraction entries out of 11-ath10k-caldata and into
the individual board's device-tree.

Some notes:
 - mmc could work as well (not tested)
 - devices that pass the partitions via mtdparts
   bootargs are kept as is
 - gl-b2200 has a weird pcie wifi device
   (vendor claims 9886 wave 2. But firmware-extraction
   was for a wave 1 device?!)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:26:55 +01:00
Christian Lamparter
10bc55c496 ipq40xx: add RT-ACRH13 alternative name to RT-AC58U
RT-ACRH13 is another name this device was sold as (US?).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:26:55 +01:00
Joshua Roys
51b9aef553 ipq40xx: add support for ASUS RT-ACRH17/RT-AC42U
SOC:	IPQ4019
CPU:	Quad-core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
DRAM:	256 MB
NAND:	128 MiB Macronix MX30LF1G18AC
ETH:	Qualcomm Atheros QCA8075 Gigabit Switch (4x LAN, 1x WAN)
USB:	1x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:	Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
WLAN2:	Qualcomm Atheros QCA9984 5GHz 802.11nac 4x4:4
INPUT:	1x WPS, 1x Reset
LEDS:	Status, WIFI1, WIFI2, WAN (red & blue), 4x LAN

This board is very similar to the RT-ACRH13/RT-AC58U. It must be flashed
with an intermediary initramfs image, the jffs2 ubi volume deleted, and
then finally a sysupgrade with the final image performed.

Signed-off-by: Joshua Roys <roysjosh@gmail.com>
(added ALT0)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:21:01 +01:00
Michael Pratt
74516f4357 ramips: fix reboot for remaining 32 MB boards
The following devices have a Winbond W25Q256FV flash chip,
which does not have the RESET pin enabled by default,
and otherwise would require setting a bit in a status register.

Before moving to Linux 5.4, we had the patch:
0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch
which kept specific flash chips with explicit 3-byte and 4-byte address modes
to stay in 3-byte address mode while idle (after an erase or write)
by using a custom flag SPI_NOR_4B_READ_OP that was part of the patch.

this was obsoleted by the patch:
481-mtd-spi-nor-rework-broken-flash-reset-support.patch
which uses the newer upstream flag SNOR_F_BROKEN_RESET
for devices with a flash chip that cannot be hardware reset with RESET pin
and therefore must be left in 3-byte address mode when idle.

The new patch requires that the DTS of affected devices
have the property "broken-flash-reset", which was not yet added for most of them.

This commit adds the property for remaining affected devices in ramips target,
specifically because of the flash chip model.

However, it is possible that there are other devices
where the flash chip uses an explicit 4-byte address mode
and the RESET pin is not connected to the SOC on the board,
and those DTS would also need this property.

Ref: 22d982ea00 ("ramips: add support for switching between 3-byte and 4-byte addressing")
Ref: dfa521f129 ("generic: spi-nor: rework broken-flash-reset")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-01-15 17:12:12 +01:00
Paul Spooren
daae59b729 at91: drop /etc/config/firewall
The file can't be part of base files or the base-files and firewall
packages collide. Two packages must not provide the same config files
without having a defined CONFLICT since it would result in an
undeterministic config state depending on what package is installed
last.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-01-15 16:36:28 +01:00
SeongUk Moon
9c8ccdcdc8 ramips: add support for ipTIME A6004NS-M
ipTIME A6004NS-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.

Specifications:
- SoC: MediaTek MT7621A (880MHz, Duel-Core)
- RAM: DDR3 256MB
- Flash: SPI NOR 16MB (Winbond W25Q128BV)
- WiFi: MediaTek MT7615E (2.4GHz, 5GHz)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x4, SoC built-in Estimated)
- USB: USB 3.0 x1
- UART: [3.3V, TX, RX, GND] (57600 8N1)

Installation via web interface:
1. Flash initramfs image using OEM's Firmware Update page.
2. Connect to OpenWrt with an SSH connection to `192.168.1.1`.
3. Perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Flash stock firmware via OEM's Recovery mode

How to use OEM's Recovery mode:
1. Power on the device and connect the shell through UART.
2. Connect to the shell and press the `t` key on the keyboard.
3. Set fixed IP with  `192.168.0.2`  with subnet mask  `255.255.255.0`
4. Flash image via TFTP to  `192.168.0.1`

Additional Notes:
1. The higher the 5Ghz Frequency, the lower the stability. It is recommended to use less than 5.775Ghz.
2. If the 5Ghz frequency is too high, 5Ghz may not work.
3. A6ns-M use shared dtsi file of A6004NS-M. (reference: /mt7621_iptime_a6004ns-m.dtsi).

Signed-off-by: SeongUk Moon <antegral@antegral.net>
[convert CRLF to LF]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-15 20:43:14 +09:00
Kyoungkyu Park
6041c693dd ramips: add support for HUMAX E2
HUMAX E2 (also known as HUMAX QUANTUM E2) is a 2.4/5GHz band AC router,
based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB (MXIC MX25L6405D)
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610E
- Ethernet: 1x 10/100Mbps
  - Switch: SoC internal
- UART: J2 (57600 8N1)
  - pinout: [3V3] (RXD) (GND) (TXD)

Installation and Recovery via TFTP:
1. Connect ethernet cable between Router port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
   of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
   You can use any TFTP client. (tftp, curl, Tftpd64...)
5. Wait until Power LED stop flashing. **DO NOT TURN OFF DEVICE!**
   The device will be automatically rebooted.

Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
2022-01-15 20:05:46 +09:00
David Bauer
7f7705923a lantiq: add additional caldata offsets
It was reported the AVM FritzBox 7430 has different offsets for the
caldata depending on the device.

Whether this is due to custom bad-block handling or up to the installed
bootloader-version is unknown.

Try both known caldata offsets like it is already done for the ipq40xx
NAND based models. Use the same approach for the FritzBox 7412. While it
is currently unknown, whether it is affected, applying the same logic
has no downsides.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-15 11:27:53 +01:00
David Bauer
3154537864 lantiq: flag FritzBox 7360 family buttons active-low
All buttons of the FritzBox 7360 family are active-low, not active-high.
Corrent the GPIO flag. This fixes release triggers upon push of a button.

Reported-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-14 22:12:53 +01:00
David Woodhouse
557067d9b1 mediatek: mt7623: Enable PCIe bus 0 (and thus SATA) on U7623
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2022-01-14 19:43:45 +00:00
Felix Fietkau
83b14ec026 ramips: enable badblock table support on linksys ea7xxx devices
Use remapping only on the kernel partitions.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
e2aa04d1e5 kernel: mtk_bmt: add support for the bbt format used on mt7621
This does not have spare blocks for remapping, and it is also not suitable
for random write access. It only skips over bad blocks on linear writes of an
image to a partition. As such, it is really only suitable for the kernel
partition, or other partitions with mostly static data

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
ff6b4f2cfb kernel: mtk_bmt: add abstraction for supporting other formats
Preparation for supporting remapping on MT7621

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
3c78fabb0d ramips: mt7621_nand: fix writing upper half of fdm data
Since the loop iterates from 0-3, subtracting 4 from the shift
multiplier does not make any sense

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
76b27f6bb9 mediatek: rework and fix mt7622-rfb1-ubi support
Limit bmt remapping range to cover everything up to and including the kernel image,
use the rest of the flash area for ubi.
Fix partition table and sysupgrade support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
7235c8d00c kernel: mtk_bmt: remap blocks after reaching bitflip threshold
This ensures that blocks are remapped before data becomes corrupt

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
0ddead0897 kernel: mtk_bmt: pass number of bitflips on read to the caller
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
b86452f841 kernel: mtk_bmt: add support for limiting range of remapping
This can be used to support ubi on top of mtk_bmt without reflashing the
boot loader. The boot loader + factory + kernel area is covered, while the
rest is passed through as-is

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
31b6cfb288 kernel: mtk_bmt: extend debug interface
Add support for showing remapped blocks and garbage collecting old
remapped blocks triggered by using the mark_good/mark_bad files

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
fde2421597 kernel: mtk_bmt: fix remapping after read/write failure
Copy from the previous block in order to preserve existing data

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
bcf91fe884 kernel: move mediatek BMT support patch to generic patches
Preparation for supporting BMT on MT7621. Move source files to the files/
subdirectory in order to simplify maintenance

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Denis Kalashnikov
2d19e6c6a4 generic: platform/mikrotik: use MTD notifier
If the SPI probe is sufficiently delayed, the routerboot driver may fail
to init as the routerboot partitions are not yet available.

Register an MTD user notifier instead of doing straight init so that the
init subroutines are only executed when the target MTD partitions are
present.

Because the init/exit routines can now be called outside of the kernel
normal init/exit calls, they cannot be jettisoned and must always be
available: the __init and __exit qualifiers are thus removed.

Reported-by: Denis Kalashnikov <denis281089@gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
[bump hardconfig/softconfig versions]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Koen Vandeputte
9571d9d4b1 ath79: qca955x: remove double declaration
No need to mention the same value twice

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Koen Vandeputte
f11df68956 ath79: rb912: remove unused property
ar934x does not define property 'rgmii-enabled' in the parsing code
remove it

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Koen Vandeputte
2a00054618 ath79: rb912: fix pll init issues
It was reported that some rb912 boards (ar934x) have issues with some ethernet speeds.
Investigation shows that the board failed to adapt the ethernet pll values as shown here:

[    5.284359] ag71xx 19000000.eth: failed to read pll-handle property

added custom prints in code and triggering a link switch:

[   62.821446] Atheros AG71xx: fast reset
[   62.826442] Atheros AG71xx: update pll 2
[   62.830494] Atheros AG71xx: no pll regmap!

Comparison with another very similar board (rb922 - QCA955x) showed a missing
reference clock frequency in dts, which seems to cause a pll init issue.
Unfortunately, no errors are printed when this occurs.

Adding the frequency property fixes the pll init as it can be parsed now
by the ethernet driver.

[   55.861407] Atheros AG71xx: fast reset
[   55.866403] Atheros AG71xx: update pll 2
[   55.870462] Atheros AG71xx: ath79_set_pllval: regmap: 0x81548000, pll_reg: 0x2c, pll_val: 0x02000000

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Oskari Lemmela
fdda3130f2 mikrotik: make soft_config writable
Parent mtd partition needs to be writable

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2022-01-13 09:33:29 +01:00
Oskari Lemmela
8441a622ec mikrotik: enable variable size erase
Add support for variable size erase blocks.
Enable it to all targets which has mikrotik targets.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2022-01-13 09:33:29 +01:00
Oskari Lemmela
6eb196ed0f generic: platform/mikrotik: make soft_config writable without 4K sectors
Make soft_config writable in all cases. Performing soft_config commit
will fail if mtd partition is not writable.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
[bump rb_softconfig version number]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Koen Vandeputte
2bb7c1db70 imx: bump SDMA firmware to v3.6
No changelog available

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2022-01-13 09:33:29 +01:00
Daniel Golle
f2c3875dfc
generic: deny write to uImage.FIT sub-image partitions
Set policy bit to force read-only mode on uImage.FIT filesystem
sub-images mapped as block partitions by the FIT partition parser.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-11 00:06:16 +00:00
David Woodhouse
8cdc356f8c mediatek: mt7623: Re-enable ARM arch timer
CONFIG_ARM_ARCH_TIMER cannot be enabled in the config directly; it is only
selected by CONFIG_HAVE_ARM_ARCH_TIMER. We need to enable the latter in
our config.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fixes: 4f1c5b01c1 ("mediatek: mt7623: backport musb, improve HDMI console")
2022-01-10 13:45:41 +00:00
David Woodhouse
4648a60058 mediatek: mt7623: Disable power button reset for U7623-02 board
The Unielec U7623 doesn't have a physical power button; I think it's hard
wired so that it turns on automatically when power is applied (unlike the
Banana Pi R2 which is a pain).

So the 'reset on long press of power button' behaviour that we get when
we enable the PMIC keyboard driver is kind of unhelpful. Disable it.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fixes: 0d3f3323a2 ("mediatek: mt7623: enable more hardware features")
2022-01-10 13:45:41 +00:00
Sven Eckelmann
97f5617259 ath79: Add support for OpenMesh OM5P-AC v1
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + AR8035 ethernet PHY (SGMII)
    + 10/100/1000 Mbps Ethernet
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-01-09 21:12:28 +01:00
Sven Eckelmann
72ef594550 ath79: Add support for OpenMesh OM5P-AN
Device specifications:
======================

* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 1T1R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
  - eth0
    + AR8035 ethernet PHY
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as LAN interface
  - eth1
    + 10/100 Mbps Ethernet
    + builtin switch port 1
    + 18-24V passive POE (mode B)
    + used as WAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-01-09 21:12:28 +01:00
Tamas Balogh
b29f4cf34c ath79: add support for ASUS RP-AC66
Asus RP-AC66 Repeater

Hardware specifications:
Board: AP152
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 25l128 16MB SPI-NOR
LAN/WAN: 1x1000M QCA8033
WiFi 5GHz: QCA9880
Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz

MAC addresses as verified by OEM firmware:
use            address   source
Lan/Wan   *:24         art 0x1002 (label)
2G             *:24         art 0x1002
5G             *:26         art 0x5006

Installation:

Asus windows recovery tool:
 - install the Asus firmware restoration utility
 - unplug the router, hold the reset button while powering it on
 - release when the power LED flashes slowly
 - specify a static IP on your computer:
     IP address: 192.168.1.75
     Subnet mask 255.255.255.0
 - Start the Asus firmware restoration utility, specify the factory image
    and press upload
 - Do not power off the device after OpenWrt has booted until the LED flashing.

TFTP Recovery method:
 - set computer to a static ip, 192.168.1.75
 - connect computer to the LAN 1 port of the router
 - hold the reset button while powering on the router for a few seconds
 - send firmware image using a tftp client; i.e from linux:
 $ tftp
 tftp> binary
 tftp> connect 192.168.1.1
 tftp> put factory.bin
 tftp> quit

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-01-09 20:32:41 +01:00
Fritz D. Ansel
693958497a mediatek mt7622: fix 300mhz typo in dts
The lowest frequency should be 300MHz, since that is the label
assigned to the OPP in the mt7622.dtsi device tree, while there is one
missing zero in the actual value.

To be clear, the lowest frequency should be 300MHz instead of 30MHz.

As mentioned @dangowrt on the OpenWrt forum there is no benefit in
leaving 30MHz as the lowest frequency.

Signed-off-by: Jip de Beer <gpk6x3591g0l@opayq.com>
Signed-off-by: Fritz D. Ansel <fdansel@yandex.ru>
2022-01-09 14:48:16 +00:00
Stefan Lippers-Hollmann
abc2821286 x86: improve sysinfo handling of dummy values
Fall back to using board_vendor and board_name, if known dummy values
are used for sys_vendor and product_name.

Examples:
	To be filled by O.E.M.:To be filled by O.E.M.
-->	INTEL Corporation:ChiefRiver

	System manufacturer:System Product Name
-->	ASUSTeK COMPUTER INC.:P8H77-M PRO

	To Be Filled By O.E.M.:To Be Filled By O.E.M.
-->	ASRock:Q1900DC-ITX

	Gigabyte Technology Co., Ltd.:To be filled by O.E.M.
-->	Gigabyte Technology Co., Ltd.:H77M-D3H

	empty:empty
-->	TYAN Computer Corporation:TYAN Toledo i3210W/i3200R S5211

	To Be Filled By O.E.M.:To Be Filled By O.E.M.
-->	ASRock:H77 Pro4-M

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2022-01-08 23:25:05 +01:00
Alex Lewontin
62a2bfaff8 ipq806x: janitorial work, respect line lengths
This commit breaks up some lines so that they are shorter than
74 charcters.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
2022-01-08 23:25:05 +01:00
Alex Lewontin
479acf03cc ipq806x: modularize generic subtarget
This commit moves the device profiles within the ipq806x/generic
subtarget into their own includable .mk file, to support eventually
having subtargets other than generic.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
2022-01-08 23:25:05 +01:00
Aleksander Jan Bajkowski
46468fc9d5 lantiq: replace patches with version accepted upstream
Replace recently added patches with version accepted upstream.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-01-08 19:32:45 +01:00
Nick McKinney
e0a574d4b7 ramips: add support for Linksys EA6350 v4
Specifications:
- SoC: MT7621DAT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 128 MB NAND
- Ethernet: 5x 1GiE MT7530
- WiFi: MT7603/MT7613
- USB: 1x USB 3.0

This is another MT7621 device, very similar to other Linksys EA7300
series devices.

Installation:

Upload the generated factory.bin image via the stock web firmware
updater.

Reverting to factory firmware:

Like other EA7300 devices, this device has an A/B router configuration
to prevent bricking.  Hard-resetting this device three (3) times will
put the device in failsafe (default) mode.  At this point, flash the
OEM image to itself and reboot.  This puts the router back into the 'B'
image and allows for a firmware upgrade.

Troubleshooting:

If the firmware will not boot, first restore the factory as described
above.  This will then allow the factory.bin update to be applied
properly.

Signed-off-by: Nick McKinney <nick@ndmckinney.net>
2022-01-08 00:49:59 +01:00
Liangkuan Yang
bc7d36ba3a ramips: add support for RAISECOM MSG1500 X.00
RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router.
Apart from the general model, there are two ISP customized models:
China Mobile and China Telecom.

Specifications:

- SoC: Mediatek MT7621AT
- RAM: 256MiB DDR3
- Flash: 128MiB NAND
- Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN
  - Switch: MediaTek MT7530 (SoC)
- WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps)
- USB: 1 * USB 2.0 port
- Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button
- LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB
- UART: 1 * serial port header (4-pin)
- Power: DC 12V, 1A
  - Switch: 1 * POWER switch

MAC addresses as verified by vendor firmware:

use   address             source
LAN   C8:XX:XX:3A:XX:E7   Config   "protest_lan_mac"  ascii  (label)
WAN   C8:XX:XX:3A:XX:EA   Config   "protest_wan_mac"  ascii
5G    C8:XX:XX:3A:XX:E8   Factory  "0x4"              hex
2.4G  CA:XX:XX:4A:XX:E8   [not on flash]

The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:

       5g                 2.4g         increment
 C8:XX:XX:90:XX:C3  CA:XX:XX:C0:XX:C3  0x30
 C8:XX:XX:3A:XX:08  CA:XX:XX:4A:XX:08  0x10
 C8:XX:XX:3A:XX:E8  CA:XX:XX:4A:XX:E8  0x10

Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.

Notes:

1. The vendor firmware allows you to connect to the router by telnet.
   (known version 1.0.0 can open telnet.)
   There is no official binary firmware available.
   Backup the important partitions data:
   "Bootloader", "Config", "Factory", and "firmware".
   Note that with the vendor firmware the memory is detected only 128MiB
   and the last 512KiB in NAND flash is not used.

2. The POWER LED is default on after press POWER switch.
   The WAN and LAN1 - 4 LEDs are wired to ethernet switch.
   The WPS LED is controlled by MT7615DN's GPIO.
   Currently there is no proper way to configure it.

3. At the time of adding support the wireless config needs to be set up
   by editing the wireless config file:

 * Setting the country code is mandatory, otherwise the router loses
   connectivity at the next reboot. This is mandatory and can be done
   from luci. After setting the country code the router boots correctly.
   A reset with the reset button will fix the issue and the user has to
   reconfigure.

 * This is minor since the 5g interface does not come up online although
   it is not set as disabled. 2 options here:

   1- Either run the "wifi" command. Can be added from LuCI in system -
      startup - local startup and just add wifi above "exit 0".

   2- Or add the serialize option in the wireless config file as shown
      below. This one would work and bring both interfaces automatically
      at every boot:

      config wifi-device 'radio0'
          option serialize '1'

      config wifi-device 'radio1'
          option serialize '1'

Flash instructions using initramfs image:

1. Press POWER switch to power down if the router is running.

2. Connect PC to one of LAN ports, and set
   static IP address to "10.10.10.2", netmask to "255.255.255.0",
   and gateway to "10.10.10.1" manually on the PC.

3. Push and hold the WIFI button, and then power up the router.
   After about 10s (or you can call the recovery page, see "4" below)
   you can release the WIFI button.
   There is no clear indication when the router
   is entering or has entered into "RAISECOM Router Recovery Mode".

4. Call the recovery page for the router at "http://10.10.10.1".
   Keep an eye on the "WARNING!! tip" of the recovery page.
   Click "Choose File" to select initramfs image, then click "Upload".

5. If image is uploaded successfully, you will see the page display
   "Device is upgrading the firmware... %".
   Keep an eye on the "WARNING!! tip" of the recovery page.
   When the page display "Upgrade Successfully",
   you can set IP address as "automatically obtain".

6. After the rebooting (PC should automatically obtain an IP address),
   open the SSH connection, then download the sysupgrade image
   to the router and perform sysupgrade with it.

Flash back to vendor firmware:

 See "Flash instructions 1 - 5" above.
 The only difference is that in step 4
 you should select the vendor firmware which you backup.

Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
2022-01-08 00:49:59 +01:00
Rodrigo Araujo
766733e172 ramips: add support for Joowin WR758AC V1 and V2
This commit adds support for Joowin (aka Comfast) WR758AC V1 and V2
devices.

Both have the same wall AP/repeater form factor and differ only
in the 5Ghz chipset (V1 has MT7662, V2 has MT7663).

OpenWrt developers forum page:
https://forum.openwrt.org/t/87355

Specifications:

 - CPU: MediaTek MT7628AN (580MHz)
 - Flash: 8MB
 - RAM: 64MB DDR2
 - 2.4 GHz: 802.11b/g/n (MT7603)
 - 5 GHz: 802.11ac (V1 has MT7662, V2 has MT7663)
 - Antennas: 4x external single band antennas
 - LAN: 1x 10/100M
 - LED: Wifi 3x blue. Programmable
 - Button: WPS

MAC addresses as verified by OEM firmware:

use address source
LAN *:83 factory 0xe000
2g *:85 factory 0x4
5g *:86 factory 0x8004

How to install:
1- Setup a TFTP server on a machine with IP address 192.168.1.10/24
2- Name the image as `firmware_auto.bin` and place it on the root of the
TFTP server
3- Connect the device via Ethernet, it should pick and flash the image

Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
2022-01-08 00:49:59 +01:00
Rui Salvaterra
536f051b97 kernel: bump 5.10 to 5.10.90
Add and enable a new kconfig knob to disable unprivileged eBPF by default.

Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-01-07 22:30:40 +01:00
John Audia
9f08557649 kernel: bump 5.4 to 5.4.170
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-07 22:30:40 +01:00
Daniel Golle
87b6e10c71
mediatek: Clause-45 MDIO patch accepted upstream
To easy future maintainance, replace the local patch with what has been
accepted into net-next and is likely to end up in Linux 5.17.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-05 14:33:56 +00:00
Matt Fawcett
b2d769673a qoriq: Expand generic subtarget description
Signed-off-by: Matt Fawcett <mattytap@icloud.com>
[remove trailing whitespace]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-01-05 10:54:59 +02:00
Daniel Golle
ef1a64caf4
mediatek: let mtk_eth_soc MAC announce 2500Base-T mode
To allows Ethernet phys supporting 2500Base-T mode to announce that
speed, enable the corresponding bit in mtk_eth_soc driver.
This should hopefully unlock 2500Base-T speed on the UniFi 6 LR.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-05 00:57:43 +00:00
Daniel Golle
6c312d9717
kernel: improve driver support for gen-3 Aquantia Ethernet PHYs
* correctly set system side interface, the original patch was
   errornous and there is a follow-up fix for it
 * enable phy statistics for AQR112(+R/C) and ARQ412
   (ethtool --phy-statistics ethX)

Tested, including phy-statistics, on
 - IEI Puzzle M901 (AQR112, AQR112C, AQR112R)
 - IEI Puzzle M902 (AQR113, AQR112R)
 - Ubiquiti UniFi 6 LR (AQR112C)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-01-05 00:57:25 +00:00
Paul Spooren
cb85aea869 uml: drop Kernel 5.4
After the switch to Kernel 5.10 the old files are no longer required.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-01-04 13:06:03 +01:00
Paul Spooren
02852d5538 uml: switch to Kernel 5.10
Switch over from testing version.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-01-04 13:05:13 +01:00
Paul Spooren
4a2cca7824 ipq807x: drop target
The target is in an incomplete state and will not receive Kernel 5.10
support, ego it should be dropped before the next release.

People are working on ipq807x with Kernel 5.15 which is only relevant
for the second next release. Once a working patchset exists the target
can be added again.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2022-01-03 10:36:09 +01:00
Ansuel Smith
1e4469b090 kernel: 5.10: backport qca8k new feature
Backport qca8k new feature:
- Ageing configuration support
- Add 2 missing counter on qca8337
- Convert to regmap
- Standardize define and code with GENMASK AND BITFILED macro
- Add mdb add/del support

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2022-01-03 01:00:04 +01:00
Ansuel Smith
5cf198f764 kernel: 5.10: backport additional qca8k fixes
Backport 3 additional fixes for qca8k.
- Fix MTU calculation
- Fix a bug with config set to the wrong PAD when secondary cpu port is defined.
- Fix redundant check in parse_port_config

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2022-01-03 01:00:04 +01:00
Rui Salvaterra
2bb02ccae3 kernel: bump 5.10 to 5.10.89
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0186-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch [1]
sunxi/patches-5.10/103-arm64-dts-allwinner-orangepi-zero-plus-fix-PHY-mo.patch [2]

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.89&id=ba696b470839d70c6b8290c1f798bac7fb2a584c
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.89&id=93a957bbf46ceb224b959de61fe85cfc6f71b6c7

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-01-03 01:00:03 +01:00
John Audia
7bf62e2451 kernel: bump 5.4 to 5.4.169
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*Had to revert 7f1edbd in order to build due to FS#4149

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-03 01:00:03 +01:00
Stefan Lippers-Hollmann
d9c2b0cfdd ipq806x: ASRock g10: fix bogus read errors
Properly declare that the g10 is booting from NAND and define its
correct (larger than on other devices-) boot_pages_size, to prevent
the kernel from constantly falling over missing OOB error correction
for the bootloader.

This patch prevents a constant slew of (bogus) read errors reported
by the kernel and keeping the CPU busy and fixes:

blk_update_request: I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
Buffer I/O error on dev mtdblock0, logical block 0, async page read
blk_update_request: I/O error, dev mtdblock0, sector 32 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 40 op 0x0:(READ) flags 0x80700 phys_seg 7 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 48 op 0x0:(READ) flags 0x80700 phys_seg 6 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 56 op 0x0:(READ) flags 0x80700 phys_seg 5 prio class 0
blk_update_request: I/O error, dev mtdblock0, sector 64 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
Buffer I/O error on dev mtdblock0, logical block 1, async page read
Buffer I/O error on dev mtdblock1, logical block 0, async page read
Buffer I/O error on dev mtdblock1, logical block 1, async page read
Buffer I/O error on dev mtdblock2, logical block 0, async page read
Buffer I/O error on dev mtdblock2, logical block 1, async page read
Buffer I/O error on dev mtdblock3, logical block 0, async page read
Buffer I/O error on dev mtdblock3, logical block 0, async page read
Buffer I/O error on dev mtdblock4, logical block 0, async page read
Buffer I/O error on dev mtdblock4, logical block 1, async page read

Suggested-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2022-01-02 20:41:50 +01:00
Shiji Yang
86d019d116 ramips: add ASUS RT-AC1200GU as alt name
RT-AC57U and RT-AC1200GU are the same models sold in different countries.
The purpose of this commit is to allow users to easily find the
corresponding firmware through the model number on the device label.

More specifications: 14e0e4f138 ("ramips: add support for ASUS RT-AC57U")

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[reword commit title/message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-02 01:31:02 +09:00
Sungbo Eo
a1deab0ec9 ramips: add support for ipTIME T5004
ipTIME T5004 is a 5-port Gigabit Ethernet router, based on MediaTek MT7621A.

Specifications:
* SoC: MT7621AT
* RAM: 128 MiB
* Flash: NAND 128 MiB
* Ethernet: 5x 1GbE
  * Switch: SoC built-in
* UART: J4 (57600 baud)
  * Pinout: [3V3] (TXD) (RXD) (GND)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware via recovery mode:
1.  Press reset button, power up the device, wait >15s for CPU LED
    to stop blinking.
2.  Upload stock image to TFTP server at 192.168.0.1.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-02 00:50:43 +09:00
Raylynn Knight
2e1206ad23 x86: add/improve support for Sophos SG/XG products
* Add support for Sophos SG/XG-115 r1, r2 with/without wireless
* Add support for Sophos SG/XG-125 r1, r2 with/without wireless
* Add wireless support for SG/XG-105

Signed-off-by: Raylynn Knight <rayknight@me.com>
2021-12-29 22:55:16 +01:00
Jinfan Lei
3928f6ae5c ath79: add usb-phy-analog to reset list in qca953x.dtsi
On startup the USB of QCA9531 board can't be initialized successfully.

lsusb result as below:
root@OpenWrt:~# lsusb unable to initialize libusb: -99

This is because usb-phy-analog is not added to reset list.

Signed-off-by: Jinfan Lei <153869379@qq.com>
(added linebreaks and small little changes to the commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-29 22:55:16 +01:00
Nick Hainke
83b5fbddf2 kernel: 5.10: add patches to fix macronix flash
mtd: spi-nor: locking support for MX25L6405D

Macronix MX25L6405D supports locking with four block-protection bits.
Currently, the driver only sets three bits.  If the bootloader does not
sustain the flash chip in an unlocked state, the flash might be
non-writeable. Add the corresponding flag to enable locking support with
four bits in the status register.

mtd: spi-nor: disable 16-bit-sr for macronix

Macronix flash chips seem to consist of only one status register.
These chips will not work with the "16-bit Write Status (01h) Command".
Disable SNOR_F_HAS_16BIT_SR for all Macronix chips.

Refreshed:
- 0052-mtd-spi-nor-use-4-bit-locking-for-MX25L12805D.patch

Fixes: 15aa53d7ee ("ath79: switch to Kernel 5.10")

Signed-off-by: Nick Hainke <vincent@systemli.org>
2021-12-29 22:55:16 +01:00
WonJung Kim
2dde2416e1 ramips: add support for ipTIME A3004T
ipTIME A3004T is a 2.4/5GHz band router, based on Mediatek MT7621.

Specifications:
 - SoC: MT7621 (880MHz)
 - RAM: DDR3 256M
 - Flash: NAND 128MB  (Macronix NAND 128MiB 3,3V 8-bit)
 - WiFi:
   - 2.4GHz: MT7615E
   - 5GHz : MT7615E
 - Ethernet:
   - 4x LAN
   - 1x WAN
 - USB: 1 * USB3.0 port
 - UART:
   - 3.3V, TX, RX, GND / 57600 8N1

Installation via web interface:
 1. Flash initramfs image using OEM's Recovery mode
 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
 - Flash stock firmware via OEM's Recovery mode

How to use OEM's Recovery mode:
 1. Power up with holding down the reset key until CPU LED stop blinking.
 2. Set fixed ip with `192.168.0.2` with subnet mask `255.255.255.0`
 3. Flash image via tftp to `192.168.0.1`

Additional Notes:
 This router shares one MT7915E chip for both 2.4Ghz/5Ghz.
 radio0 will not working on 5Ghz as it's not connected to the antenna.

Signed-off-by: WonJung Kim <git@won-jung.kim>
(added led dt-bindings)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-29 20:35:57 +01:00
Sungbo Eo
482a7e23a4 ramips: add support for WeVO AIR DUO
WeVO AIR DUO is a 1-bay NAS & 802.11ac (Wi-Fi 5) router, based on
MediaTek MT7620A.

Specifications:
* SoC: MT7620A
* RAM: 64 MiB
* Flash: SPI NOR 16 MiB
* USB & SATA bridge controller: JMicron JMS567
  * SATA 6Gb/s: 2.5" drive slot
  * USB 3.0: Micro-B
  * USB 2.0: connected to SoC
* Wi-Fi:
  * 2.4 GHz: SoC built-in
  * 5 GHz: MT7612EN
* Ethernet: 5x 1GbE
  * Switch: MT7530WU
* UART: 4-pin 1.27 mm pitch through-hole (57600 baud)
  * Pinout: (3V3)|(RXD) (TXD) (GND)

Notes:
* The drive is accessible through the external USB port only when the
  router is turned off.

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
    The image filename should have ".upload" extension.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-29 20:35:57 +01:00
Torsten Duwe
7ea9936f7f bcm27xx: add AMP2 to HifiBerry DAC+ / DAC+ Pro package
According to the vendor [1] these HATs share the same DT overlay:
hifiberry-dacplus. The PCM512x-compatible control unit is attached to
I2C, so the additional snd-soc-pcm512x-i2c kernel module is required.
Also explicitly note the Amp2 support to reduce confusion for those
users.

[1] <https://www.hifiberry.com/docs/software/configuring-linux-3-18-x/>
Signed-off-by: Torsten Duwe <duwe@lst.de>
(added bcm27xx tag, changed commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-29 20:35:57 +01:00
Pawel Dembicki
afd7ec3b57 kirkwood: add support for two clones from Endian
They are Endian 4i Edge 200 and his clone Endian UTM Mini.

Hardware:
  - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz
  - Ram: 512MB (4x Nanya NT5TU128M8GE-AC)
  - NAND Flash: 512MB (Micron 29F4G08AAC)
  - Lan 1-4: 4x GBE (Marvell 88E6171R-TFJ2)
  - Lan 5: 1x GBE (Marvell 88E1116R-NNC1)
  - Storage: MicroSD Slot
  - WLAN: MiniPCIe Slot present, and fitted with SparkLan WPEA-110N/E
          (Atheros AR9280 chipset) (ONLY Endian UTM Mini WLAN)
  - USB: 1x USB 2.0 port
  - Console: RJ-45 port
  - LEDs: 3x GPIO controlled

Notes:
  - WLAN led (Endian UTM Mini) is drived by MPCIE card

Installation by TFTP + serial:
  - Setup TFTP server and copy initramfs image
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
	saveenv
	setenv serverip 192.168.1.1
	setenv ipaddr 192.168.1.2
	tftpboot 0x1200000 openwrt-kirkwood-endian_4i-edge-200-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Installation by USB + serial:
  - Copy initramfs image to fat32 usb drive
  - Connect pendrive to USB 2.0 front socket
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
        saveenv
	usb reset
	fatload usb 0:1 0x1200000 openwrt-kirkwood-endian_4i-edge-200-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-29 20:35:57 +01:00
Pawel Dembicki
4e46ae1f69 kirkwood: add support for NETGEAR ReadyNAS Duo v2
NETGEAR ReadyNAS Duo v2 is a NAS based on Marvell kirkwood SoC.

Specification:
 - Processor Marvell 88F6282 (1.6 GHz)
 - 256MB RAM
 - 128MB NAND
 - 1x GBE LAN port (PHY: Marvell 88E1318)
 - 1x USB 2.0
 - 2x USB 3.0
 - 2x SATA
 - 3x button
 - 5x leds
 - serial on J5 connector accessible from rear panel
   (115200 8N1) (VCC,TX,RX,GND) (3V3 LOGIC!)

Installation by USB + serial:
  - Copy initramfs image to fat32 usb drive
  - Connect pendrive to USB 2.0 front socket
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	usb reset
        setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
        setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
        saveenv
	fatload usb 0:1 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Installation by TFTP + serial:
  - Setup TFTP server and copy initramfs image
  - Connect serial console
  - Stop booting in u-boot
  - Do:
	setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
	setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
	saveenv
	setenv serverip 192.168.1.1
	setenv ipaddr 192.168.1.2
	tftpboot 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
	bootm 0x1200000
  - copy sysupgrade image via ssh.
  - run sysupgrade

Known issues:
  - Power button and PHY INTn pin are connected to the same GPIO. It
    causes that every network restart button is pressed in system.
    As workaround, button is used as regular BTN_1.

For more info please look at file:
RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c
from Netgear GPL sources.

Tested-by: Raylynn Knight <rayknight@me.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-29 20:35:57 +01:00
Pawel Dembicki
4e82a80b68 kernel: generic: backport linkstation-poweroff driver
Linkstation poweroff driver was added to mvebu target, but is required
for kirkwood target too.
This commit make two changes:
- move linkstation-poweroff support patch from mvebu to generic and
replace upstream accepted version
- backport small linkstation-poweroff fix from 5.12

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-29 20:35:57 +01:00
David Bauer
79a81d36ae ath79: remove pre-5.10 specific kernel code
With Kernel 5.4 support removed, we can get rid of this legacy code.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-29 03:44:56 +01:00
David Bauer
00b194871c ramips: aw9523: add can_sleep flag for GPIO chip
The GPIO expander is connected via I2C, thus the can_sleep flag has to
be set to true. This should fix spurious "scheduling while atomic" bugs
in the kernel ringbuffer.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-29 03:43:03 +01:00
Daniel Golle
92820cc5b9
mediatek: yet again, replace patch with updated pending patch
Upon comment of Russell King ('Oh no, not this "-1 disease" again.')
clean up mdio read and write return type and value in mtk_eth_soc
driver and also use appropriate return values for bus-busy-timeout-
errors in newly added Clause 45 access code.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-27 20:20:10 +00:00
Daniel Golle
c555c34dd1
mediatek: replace patch with version sent upstream
Replace recently added patch
 701-net-ethernet-mtk_eth_soc-add-support-for-clause-45-mdio.patch
with version sent upstream
 701-net-ethernet-mtk_eth_soc-implement-Clause-45-MDIO-access.patch

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-27 16:24:23 +00:00
Sergey Ryazanov
5deb3996e2 ath25: add kernel 5.10 support
Copy and refresh patches and config from 5.4 to 5.10. Most patches
require no more then automatic refresh. The only exception is the
Ethernet driver patch, which requires some more work:
* drop eth_change_mtu() usage since it was removed from the kernel,
  it anyway useless for drivers that utilizes alloc_etherdev();
* add the txqueue number argument to the .ndo_tx_timeout callback
  function;
* replace ioremap_nocache() which was finally removed from the kernel by
  the ioremap() with the same behaviour.

Switch target to the new kernel version.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[use KERNEL_TESTING_PATCHVER for now]
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-27 16:00:21 +00:00
Sergey Ryazanov
5bf8ae7c4b ath25: refresh kernel 5.4 config
The target config require some refresh due to the just introduced
filtering of the "run-time" options, MIPS eBPF JIT backporting, and so
on.

The configuration is easily updated using make kernel_oldconfig. So
let's update it now in preparation for v5.10 support to reduce the new
kernel configuration diff.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-27 16:00:21 +00:00
Sergey Ryazanov
0b2c1d8b9a Move mvswitch 88E6060 driver to the ath25
ath25 requires a 88E6060 driver to support boards such as Fonera 2.0g
(FON2202). The swconfig based mvswitch driver has not yet been ported to
the 5.10 kernel as the only user is the ath25 target while all other
targets have been switched to the upstream DSA implementation.

Switching ath25 to the DSA implementation is a complex task, since we
need either per-board platform data or DTS support. ath25 lacks both of
them and builds only a single generic image. So we need to keep the
swconfig driver implementation to easly and quickly port ath25 to the
5.10 kernel.

Since porting the mvswitch driver to 5.10 as a generic driver is not an
option, and since the ath25 is its only user, make mvswitch a target
specific driver to be able to port it to the 5.10 kernel as part of the
kernel version update of the target. This will allow us quickly migrate
to the next kernel version and not delay the next firmware release.

Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-27 16:00:21 +00:00
Rui Salvaterra
a3774d72c8 kernel: bump 5.10 to 5.10.88
Deleted (upstreamed):
mpc85xx/patches-5.10/002-powerpc-85xx-fix-oops-when-CONFIG_FSL_PMC-n.patch [1]

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.88&id=151ffac3ac277ad7c2a5f201b566b56d97ed3a99

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-12-27 16:00:21 +00:00
Christian Lamparter
0e841fd4a2 apm821xx: remove broken PCIe MSI support
These never worked and upstream is in the process of removing
them as well. Legacy PCI interrupt signaling is still working
as before.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-27 13:55:10 +01:00
Christian Lamparter
4e6ebdd7ce apm821xx: remove overlapping partitions
Apart from the dtb partition, these were all "read-only;"
they serve no purpose other than being a copy of what
netgear had defined in their original firmware.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-27 13:55:10 +01:00
Christian Lamparter
832b9cbd74 apm821xx: fix WD MyBook Live DUO USB-Port
where to begin? the USB regulator settings were just
a part of the issue. With them changed, according to
the forum it still failed when a USB device was
connected to the port with:

dwc2 4bff80000.usbotg: dwc2_restore_global_registers: no global registers to restore
dwc2 4bff80000.usbotg: dwc2_exit_partial_power_down: failed to restore registers
dwc2 4bff80000.usbotg: exit partial_power_down failed
dwc2 4bff80000.usbotg: HC died; cleaning up

One clue was found upstream in
commit cc10ce0c51b1 ("usb: dwc2: disable power_down on Amlogic devices")

|Disable power_down by setting the parameter to
|DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
|Meson SoCs where USB devices are only recognized when plugged in before
|booting Linux. A hot-plugged USB device was not detected even though the
|device got power (my USB thumb drive for example has an LED which lit
|up).
|[...]

the same method proposed there worked with APM821xx's USB IP-Core.

Link: https://forum.openwrt.org/t/wd-my-book-duo-usb/111926/2
Reported-by: thwe and takimata (openwrt forum)
Fixes: b70d3557e0 ("apm821xx: clean up gpio-hogs")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-27 13:55:10 +01:00
Christian Lamparter
2593d510e2 apm821xx: drop 5.4 config and patches
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-27 13:51:41 +01:00
Sander Vanheule
ebc0ce118f realtek: netgear-gs110tpp: Add system LEDs
The GS110TPP has an RGB LED used for system status indication. Expose
all three components as separate GPIO LEDs connected via the device's
RTL8231.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-12-27 13:51:41 +01:00
Sander Vanheule
c88124cfc4 realtek: netgear-gigabit: Enable RTL8231
Since the move to 5.10, there are now two GPIO drivers. The gpio0 node
refers to the internal GPIOs, so the indirect-access-bus-id is no longer
relevant for that node.

Set indirect-access-bus-id to the correct value (31) on the correct node
(gpio1) and enable the device.

Cc: Raylynn Knight <rayknight@me.com>
Cc: Michael Mohr <akihana@gmail.com>
Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Bjørn Mork <bjorn@mork.no>
2021-12-27 13:51:41 +01:00
Ansuel Smith
5761aa4d9e kernel: mtd: parsers: add nvmem support to cmdlinepart
Assuming cmdlinepart is only one level deep partition scheme and that
static partition are also defined in DTS, we can assign an of_node for
partition declared from bootargs.

The cmdlinepart parser is the first parser checked and if it does find
some partition declared in the bootargs, every other parser is ignored.
This means that the fixed-partition parser is ignored and an of_node for
the mtd is never assigned.
Fix this by searching a defined of_node using a similar fixed_partition
parsing logig, check if a partition is present with the same label, check
that it has the same offset and size and finally assign an of_node to the
mtd. The NVMEM can now find the of_node for the mtd and correctly works.

Fixes: abc17bf306 ("ath79: convert mtd-mac-address to nvmem implementation")
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-12-27 13:51:41 +01:00
David Bauer
e1780de5ce rockchip: remove Kernel 5.4
As v5.10 is the default kernel version now, the files for v5.4 can be
dropped.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-27 03:13:36 +01:00
David Bauer
13f326de3a mpc85xx: remove kernel 5.4
As v5.10 is the default kernel version now, the files for v5.4 can be
dropped.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-27 03:13:36 +01:00
David Bauer
9d9d851eec ath79: remove kernel 5.4
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-27 03:13:36 +01:00
Nick Hainke
cfa670bf16 ath79: add missing UBNT_REVISION
The UBNT_REVISION was already added for the ubnt-xw target because:

  U-boot bootloader on M-XW devices expects factory image revision
  version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
  (May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
  number is actually a number, but in currently generated images there's
  OpenWrt text and so the check fails

  ...

  By placing arbitrary correct number first in major version, we make the
  bootloader happy and we can flash factory images over TFTP again.

  commit d42a7c4699 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method")

Fixes errors in the form of (tftp flashing):
  sent DATA <block=8577, 412 bytes>
  received ERROR <code=2, msg=Firmware check failed>
  Error code 2: Firmware check failed

The missing UBNT_REVISION was not noticed before, since the
UBNT_REVISION field for the ubnt-xm target was also set to:
  "42.OpenWrt-..."
Probably, UBNT_REVISION for the ubnt-xm target was set by the ubnt-xw
and was never overridden somewhere else. However, it is missing and
should be part of the ubnt-xm device.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2021-12-27 03:07:22 +01:00
Hauke Mehrtens
0dc4ab344b sunxi: Use rtl8723bu-firmware instead of rtl8723bs-firmware
The firmware for the rtl8723bs chip is now included in the
rtl8723bu-firmware package.

Fixes: 397dfe4a97 ("linux-firmware: Update to version 20121216")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-12-27 00:58:29 +01:00
Daniel Golle
8b6d6f28c1
mediatek: mt7622: unifi6lr: properly register Ethernet PHY
This change enables proper Ethernet link status and speed reporting on
the Ubiquiti UniFi 6 LR access point:

 mtk_soc_eth 1b100000.ethernet eth0: PHY [mdio-bus:08] driver [Aquantia AQR112C] (irq=POLL)
 mtk_soc_eth 1b100000.ethernet eth0: configuring for phy/2500base-x link mode
 mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-26 19:11:54 +00:00
Daniel Golle
e6c08c8272
mediatek: mt7622: enable driver for Aquantia PHYs
Enable Aquantia Ethernet PHY driver as there is an AQR112C 2500Base-T
PHY in the Ubiquiti UniFi 6 LR access point.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-26 19:11:49 +00:00
Daniel Golle
13b3474294
mediatek: add support for Clause 45 MDIO access
Add support for Clause 45 MDIO PHY register read and write operations
to mtk_eth_soc driver.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-26 19:11:43 +00:00
Daniel Golle
215c78eef5
kernel: generic: refresh patch
722-net-phy-aquantia-Add-AQR113-driver-support.patch needs refresh.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-26 19:11:36 +00:00
Rafał Miłecki
65974aa18b bcm4908: include ATF in bootfs images
It's required for proper booting.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-24 23:07:39 +01:00
Daniel Golle
f9782f5bcd
mvebu: puzzle: wan LED and fix default network
Fix default network configuration of the Puzzle-M902 so all LAN ports
are included in the LAN bridge.
Setup network LED to indicate WAN port link status, like vendor
firmware does as well.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:47 +00:00
Daniel Golle
f81a06408e
mvebu: enable Aquantia phy driver for Puzzle devices
Fixes Ethernet link status on all ports and makes 2.5G ports usable
in 2.5G and 1G full-duplex mode.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:42 +00:00
Daniel Golle
7b9d2d6f7b
kernel: add id for AQR112 Ethernet phy variants
Add ids for AQR112R and AQR112C 2.5G Ethernet PHYs.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:37 +00:00
Daniel Golle
73c0ef1ecf
kernel: import patch enabling AQR113 PHY
Add PHY ID for the Aquantia AQR113 PHY.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:32 +00:00
Daniel Golle
6563a6a3ba
kernel: import patch enabling AQR112 and AQR412 PHY
Copy and refresh patch enabling AQR112 and AQR412 Ethernet PHY from
layerscape (5.4) target to generic (5.10) as AQR112 can also be found
on other targets as well.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:28 +00:00
Daniel Golle
962c585580
mvebu: remove accidentally added file
Remove accidentally added file (which was a left-over of a by-now
replaced driver)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 23:44:45 +00:00
Daniel Golle
3684b494dd
mvebu: puzzle-m901: add LEDs, fan and reset button
Wire up MCU driver for LEDs, fan and temperature sensor, and add
GPIO reset button just like on the M902 also on the Puzzle M901.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 21:54:54 +00:00
Daniel Golle
ddad936fc6
mvebu: puzzle-m902: add GPIO reset button
Add reset button to device tree so it has the function expected from
usual OpenWrt devices.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 21:54:49 +00:00
Daniel Golle
7e4c1cca8a
mvebu: puzzle-mcu: improve led driver
Set blinking mode using scheduled work instead of blocking which may
result in deadlocks.
Add dynamic kprintf debugging hexdumps of all MCU rx and tx.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 21:54:42 +00:00
Paul Spooren
15aa53d7ee ath79: switch to Kernel 5.10
Kernel 5.10 is used by many people since quite a while. With other
targets already moved to 5.10, let ath79 follow suit.

Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ath79/tl-wdr3600; ath79/tl-wdr4300]
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> [ath79/tl-wdr4300]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-21 21:38:52 +01:00
Stijn Tintel
3fda16078b qoriq: add support for WatchGuard Firebox M300
This device is based on NXP's QorIQ T2081QDS board, with a quad-core
dual-threaded 1.5 GHz ppc64 CPU and 4GB ECC RAM. The board has 5
ethernet interfaces, of which 3 are connected to the ethernet ports on
the front panel. The other 2 are internally connected to a Marvell
88E6171 switch; the other 5 ports of this switch are also connected to
the ethernet ports on the front panel.

Installation: write the sdcard image to an SD card. Stock U-Boot will
not boot, wait for it to fail then run these commands:

setenv OpenWrt_fdt image-watchguard-firebox-m300.dtb
setenv OpenWrt_kernel watchguard_firebox-m300-kernel.bin
setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; ext2load mmc 0:1 $fdtaddr $OpenWrt_fdt; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr - $fdtaddr'
saveenv
reset

The default U-Boot boot entry will now boot OpenWrt from the SD card.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-12-21 21:37:46 +02:00
Stijn Tintel
080a769b4d qoriq: new target
Add a new target named "qoriq", that will support boards using PowerPC
processors from NXP's QorIQ brand.

This doesn't actually add support for any board yet, so that
installation instructions can go in the commit message of the commit
that adds actual support for a board.

Using CONFIG_E6500_CPU here due to the kernel using -mcpu=powerpc64
rather than -mcpu=e5500 when selecting CONFIG_E5500_CPU. The only
difference between e5500 and e6500 is AltiVec support, and the kernel
checks for it at runtime. Musl will only check at runtime if AltiVec
support is disabled at compile-time, so we need to use e5500 in CPU_TYPE
to avoid SIGILL.

Math emulation (CONFIG_MATH_EMULATION_HW_UNIMPLEMENTED) is required, as
neither e5500 nor e6500 implement fsqrt nor fsqrts, and musl hardcodes
sqrt and sqrtf to use these ASM instructions on PowerPC64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-12-21 21:37:39 +02:00
Daniel Golle
f0c0b18234
mvebu: puzzle-m902: add driver for MCU driving LEDs, fan and buzzer
Backport MFD driver for communicating with the on-board MCU found on
IEI World Puzzle appliances.
Improve the driver to support multiple LEDs, apply a default state and
let MCU take care of blinking if timing is within supported range.
Wire up LEDs and fan for Puzzle M902 in device tree.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 16:41:10 +00:00
David Bauer
b1d483b865 ramips: work around duplicate MAC address on U6 Lite
The UniFi 6 Lite has two MAC addresses for the 2.4 and 5GHz radio in
it's EEPROM partition.

On my unit these are

F4 92 BF A0 BB 6F
F6 92 BF A0 BB 6F

The problem with these is that mac80211 increases the first octet by
2, which leads to conflicting MAC addresses between radios.

Work around this problem for now by increasing the last octet by 1 on
the 5 GHz radio.

Ubiquiti increases the last octet by 2 for each subsequent VAP created
per radio. Ideally we should do the same, however this functionality is
currently lacking from mac80211.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-20 00:12:12 +01:00
Daniel Golle
5a4685cfa2
mediatek: mt7623: bpi-r2: add ethernet alias to device tree
Add ethernet0 alias in device tree to make U-Boot inherit the Ethernet
mac address (set via environment variable 'ethaddr') down to Linux.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-18 01:52:19 +00:00
Sergey Ryazanov
fa3690f8f1 kernel: 5.10: consolidate mac80211 crypto options
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2

either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.

CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-17 16:16:34 +01:00
Sergey Ryazanov
b61ab8f57e kernel: filter out both Clang and LLD versions
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-17 16:16:34 +01:00
John Audia
43c0a12665 kernel: bump 5.10 to 5.10.85
Removed target for patch which does not exist:
    bcm27xx/patches-5.10/950-0249-kbuild-Disable-gcc-plugins.patch

All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800*
Run-tested: bcm2711/RPi4B, ipq806x/R7800*

* Had to revert 7f1edbd412 in order to build
  (binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
John Audia
187c8f9153 kernel: bump 5.10 to 5.10.84
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
John Audia
d4b25007ea kernel: bump 5.4 to 5.4.167
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
John Audia
61c76f836f kernel: bump 5.4 to 5.4.166
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
John Audia
a696e325f7 kernel: bump 5.4 to 5.4.165
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
Sungbo Eo
cc3e390a74 ramips: mt7620: tidy up 02_network
* fix alphabetic sorting
* consolidate duplicate cases

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-16 22:28:58 +09:00
Rafał Miłecki
444b4ea4a4 bcm4908: add uboot-envtools to default packages
It's required by sysupgrade to access UBI metadata partitions.

Fixes: 5f05795aa7 ("bcm4908: sysupgrade: add pkgtb format support")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-16 08:26:25 +01:00
Rafał Miłecki
85ad48c957 kernel: backport support for multicolor & RGB LEDs to 5.4
This is a requirement for backporting DT files defining such LEDs.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-16 07:18:05 +01:00
Felix Fietkau
01bebc070c kernel: backport the upstream implementation of threaded NAPI to 5.4
The workqueue based implementation has a few corner cases and typically lower
performance than the upstream one

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-12-15 20:36:22 +01:00
Rui Salvaterra
c772783394 ramips: remove Linux 5.4 support
We're at 5.10 stable, this can finally go.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-12-15 09:40:03 +00:00
David Bauer
07452a680b ramips: fix Tenbay T-MB5EU v1 Wireless MAC
It was reported, that Tenbay T-MB5EU v1 do have incorrect Wireless MAC
address set on 2.4 and 5 GHz.

Some boards do not seem to have the correct MAC address set for the
external PHY of the MT7915 radio at caldata offset 0xa.

As the external PHY does not expose a DT binding (yet), fix up the mac
address in userspace.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-15 00:13:40 +01:00
Rafał Miłecki
30b93672ec bcm4908: add fdt-utils to default packages
It's required by sysupgrade.

Fixes: 5f05795aa7 ("bcm4908: sysupgrade: add pkgtb format support")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-14 17:58:20 +01:00
Martin Schiller
60881f657d layerscape: armv7: refresh config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
7af83d2c03 layerscape: armv7: copy config-5.4 to config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
fef79a5dc4 layerscape: armv8_64b: refresh config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
a939015dd1 layerscape: armv8_64b: copy config-5.4 to config-5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
83035a44a7 layerscape: armv8_64b: use non-SDK dts files for linux-5.10 or newer
Since we decided to drop the LSDK patches with linux-5.10, we now have
to switch to the corresponding upstream dts files as well.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
82ce460ab1 layerscape: armv8_64b: fix KERNEL_LOADADDR for linux >= 5.8
In kernel versions newer than 5.8 the arm64 TEXT_OFFSET (0x80000) has
been set to 0x0 (and later removed). This will break Uimages with kernel
load addresses that aren't 2MiB aligned any longer. Resulting in the
kernel silently fail to boot. For layerscape armv8_64b targets this
needs to be changed to 0x80000000 (start of RAM).

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
68b4e9fe0e layerscape: add patches for kernel 5.10
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
7e35d86ca2 layerscape: add kernel 5.10 as testing version
This patch adds "KERNEL_TESTING_PATCHVER:=5.10" to the Makefile in
layerscape target to allow using Kernel 5.10 for testing.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Martin Schiller
0a9454918d layerscape: remove unneeded KERNEL_ENTRY_POINT definition
As KERNEL_ENTRY_POINT is identical to KERNEL_LOADADDR, drop it.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2021-12-13 23:22:29 +01:00
Rui Salvaterra
66f9ed1684 ramips: switch to kernel 5.10
Tested on mt7621 (Redmi AC2100) and running stable for several months.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2021-12-13 19:36:52 +01:00
Pawel Dembicki
794e8123ce ramips: mt7620: use OKLI loader with Jboot devices
Jboot devices have problem with >2MB kernelsize. The only way to avoid
this problem is use small loader.

This patch switch all mt7620 Jboot devices to lzma OKLI loader.

Suggested-by: Szabolcs Hubai <szab.hu@gmail.com>
Co-authored-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-13 19:36:10 +01:00
Rafał Miłecki
3bcf3e8143 bcm53xx: sysupgrade: fix support for Luxul's legacy firmware format
Fixes: 80041dea70 ("bcm53xx: sysupgrade: refactor handling different firmware formats")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-13 18:19:35 +01:00
Rafał Miłecki
5f05795aa7 bcm4908: sysupgrade: add pkgtb format support
BCM4908 devices with U-Boot use pkgtb firmware format. It's based on
U-Boot's FIT: DTB with configurations, images & embedded data.

This format contains bootfs, rootfs and optionally a first stage U-Boot
loader. Contained images need to be extracted & flashed.

Broadcom used two sets of firmwares: main & backup. It uses UBI volumes
"metadata1" & "metadata2" for storing U-Boot env variables with info
about flashed images.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-13 08:53:00 +01:00
Moritz Warning
59faf41da1 treewide: use uniform vendor value for british telecom
British Telecom is mostly known as BT.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2021-12-12 21:11:38 +01:00
John Audia
6c945fa379 kernel: bump 5.10 to 5.10.83
Removed upstreamed:
    bcm53xx/patches-5.10/033-v5.16-0024-ARM-dts-BCM5301X-Fix-I2C-controller-interrupt.patch[1]
    bcm53xx/patches-5.10/033-v5.16-0025-ARM-dts-BCM5301X-Add-interrupt-properties-to-GPIO-no.patch[2]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=b2cd6fdcbe0a5cb44e4610a08cc58261d494a885
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=9db1d4a3c2700e1cc84c3d61199411d75c2a3ec6

Build system: x86_64*
Build-tested: bcm2711/RPi4B, ipq806x/R7800†
Run-tested: bcm2711/RPi4B, ipq806x/R7800†

* Had to revert 7c99085bd6 in order to build
  (latest bump of ca-certificates)

† Had to revert 7f1edbd412 in order to build
  (binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-12 21:11:30 +01:00
Enrico Mioso
a725bdc700 ipq40xx: fix reset button GPIO for GL.iNet GL-B2200
GL.iNet's U-Boot checks for GPIO 40, not 43.
Changing this allows the RESET button to work as expected.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Daniel Golle <daniel@makrotopia.org>
CC: Li Zhang <li.zhang@gl-inet.com>
2021-12-12 19:14:16 +00:00
Kyoungkyu Park
9a1b9a42b7 ramips: add support for HUMAX E10
HUMAX E10 (also known as HUMAX QUANTUM E10) is a 2.4/5GHz band AC router,
based on MediaTek MT7621A.

Specifications:
- SoC: MT7621A
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB (MXIC MX25L12805D)
- WiFi:
  - 2.4GHz: MT7615
  - 5GHz: MT7615
- Ethernet: 2x 10/100/1000Mbps
  - Switch: SoC internal
- USB: 1x USB 2.0 Type-A
- UART: J1 (57600 8N1)
  - pinout: [3V3] (RXD) (GND) (TXD)

Installation via web interface:
- Flash **factory** image through the stock web interface.

Recovery procedure:
1. Connect ethernet cable between Router **LAN** port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
   of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
   You can use any TFTP client. (tftp, curl, Tftpd64...)
- It can accept both images which is
  HUMAX stock firmware dump (0x70000-0x1000000) image
  and OpenWRT **sysupgrade** image.

Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
[remove trailing whitespace]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-12 20:33:19 +09:00
Sungbo Eo
91e37b60a0 ramips: mt76x8: tidy up 02_network
* fix alphabetic sorting
* consolidate duplicate cases

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-12 20:25:56 +09:00
Felix Fietkau
3b20eb185b kernel: fix RCU issue in xt_FLOWOFFLOAD patch
cond_resched() may not be called in a rcu-locked section

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-12-11 13:52:39 +01:00
Christian Lamparter
b2aca5a263 ath79: fix various dts warnings
ar9344_openmesh_mr600-v1.dts:40.10-44.5: Warning (gpios_property):
/leds-ath9k/wifi2g: Missing property '#gpio-cells' in node
/ahb/pcie-controller@180c0000/wifi@0,0 or bad phandle
=> added gpio-controller + #gpio-cells

qca955x_zyxel_nbg6x16.dtsi:121.3-13: Warning (reg_format):
/ahb/usb@1b000000/port@1:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
../dts/qca955x_zyxel_nbg6x16.dtsi:131.3-13: Warning (reg_format):
/ahb/usb@1b400000/port@1:reg: property has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
qca955x_zyxel_nbg6x16.dtsi:120.20-123.4: Warning (avoid_default_addr_size):
/ahb/usb@1b000000/port@1: Relying on default #address-cells value
=> ath79's usb-nodes are missing the address- and size-cells properties.
These are needed for usb led trigger support.

ar7242_ubnt_sw.dtsi:54.4-14: Warning (reg_format): /gpio_spi/gpio_spi@0:reg:
property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
=> the #address-cells and #size-cells had to be nudged.

qca9531_dlink_dch-g020-a1.dts:19.6-39.4: Warning (i2c_bus_bridge):
/i2c: incorrect #size-cells for I2C bus
=> #size-cells = <0>;

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-11 00:50:02 +01:00
Joel Linn
7061d5f343 lantiq: fixed wifi support for AVM FRITZ!Box 7430
adds the correct offset for the calibration data.
The values are according to the OpenWrt Forum Thread:
"Fritzbox 7430 and wifi".

Link: <https://forum.openwrt.org/t/fritzbox-7430-and-wifi/86944>
Reported-by: RENErica
Signed-off-by: Joel Linn <jl@conductive.de>
[changed commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-11 00:50:02 +01:00
Ryan Mounce
35aecc9d4a ath79: add support for WD My Net N600
SoC: AR9344
RAM: 128MB
Flash: 16MiB SPI NOR
5GHz WiFi: AR9382 PCIe 2x2:2 802.11n
2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n

5x Fast ethernet via SoC switch (green LEDs)
1x USB 2.0
4x front LEDs from SoC GPIO
1x front WPS button from SoC GPIO
1x bottom reset button from SoC GPIO

UART header JP1, 115200 no parity 1 stop
TX
GND
VCC
(N/P)
RX

Flash factory image via "emergency room" recovery:
- Configure your computer with a static IP 192.168.1.123/24
- Connect to LAN port on the N600 switch
- Hold reset putton
- Power on, holding reset until the power LED blinks slowly
- Visit http://192.168.1.1/ and upload OpenWrt factory image
- Wait at least 5 minutes for flashing, reboot and key generation
- Visit http://192.168.1.1/ (OpenWrt LuCI) and upload OpenWrt sysupgrade image

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
[dt leds preparations]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-11 00:50:02 +01:00
Olivier Valentin
7853453950 ath79: add support for jjPlus JWAP230
The jjPlus JWAP230 is an access point board built around the QCA9558,
with built-in 2.4GHz 3x3 N WiFi (28dBm). It can be expanded with 2
mini-PCIe boards, and has an USB2 root port.

Specifications:
- SOC: Qualcomm Atheros QCA9558
- CPU: 720MHz
- H/W switch: QCA8327 rev 2
- Flash: 16 MiB SPI NOR (en25qh128)
- RAM: 128 MiB DDR2
- WLAN: AR9550 built-in SoC bgn 3T3R (ath9k)
- PCI: 2x mini-PCIe (optional 5V)
- LEDs: 6x LEDs (3 are currently available)
- Button: 1x Reset (not yet defined)
- USB2:
  - 1x Type A root port
  - 1x combined mini-PCIe
- Ethernet:
  - 2x 10/100/1000 (1x PoE 802.3af (36-57 V))

Notes:
 The device used to be supported in the ar71xx target.
 For upgrades: Please use "sysupgrade --force -n <image>".
 This will restore the device back to OpenWrt defaults!

MAC address assignment:
    use   source
    LAN   art 0x0
    WAN   art 0x6
    WLAN  art 0x1002 (as part of the calibration data)

Flash instructions:
- install from u-boot with tftp (requires serial access)
  > setenv ipaddr a.b.c.d
  > setenv serverip e.f.g.h
  > tftp 0x80060000 \
      openwrt-ath79-generic-jjplus_jwap230-squashfs-sysupgrade.bin
  > erase 0x9f050000 +${filesize}
  > cp.b $fileaddr 0x9f050000 $filesize
  > setenv bootcmd bootm 0x9f050000
  > saveenv

Signed-off-by: Olivier Valentin <valentio@free.fr>
[Added DT-Leds (based on ar71xx), Added more notes about sysupgrade,
fixed "qca9550" to match SoC in commit and dts file name]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-11 00:50:02 +01:00
Christian Lamparter
4deaeaa13c x86: remove old lzma tuning patch
Chen Minqiang reported in his GitHub PR  that:
With CONFIG_TARGET_INITRAMFS_COMPRESSION_LZMA=y option set,
the popular x86/amd64 target's initramfs-kernel failed to boot.

The cause for this boot failure is that the LZMA compression
uses a the first bytes to encode the compression parameters.
It does not have a fixed magic. Yes, this only works if the
the existing lzma options in the upstream are not changed.

This patch does away with OpenWrt special LZMA options tuning
since it is rather unlikely that upstream will improve the
compression algorithm detection after all this time. Even
though, the tuning produced a smaller initramfs (~1.1% in a
spot check).

Link: <https://github.com/openwrt/openwrt/pull/4733>
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-11 00:50:02 +01:00
Stan Grishin
ffab23d99d x86: add/improve support for Sophos SG/XG products
* Better product ID for Sophos SG/XG-105 models
* Add support for Sophos SG/XG-135 r1, r2 with/without wireless

Signed-off-by: Stan Grishin <stangri@melmac.ca>
[Changed subject to x86 - probably eaten somewhere, the PR had it]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-11 00:50:02 +01:00
Josef Schlehofer
1c4b3ce344 kernel: add more disabled config options
NET_DSA_MSCC_FELIX:

Marvell 88E6xxx Ethernet switch fabric support (NET_DSA_MV88E6XXX) [N/m/y/?] n
Ocelot / Felix Ethernet switch support (NET_DSA_MSCC_FELIX) [N/m/y/?] (NEW)
Error in reading or end of file.

make[6]: *** [scripts/kconfig/Makefile:71: syncconfig] Error 1
make[5]: *** [Makefile:603: syncconfig] Error 2

IR_IMON_RAW:
    SoundGraph iMON Receiver (early raw IR models) (IR_IMON_RAW) [N/m/?] (NEW)

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[squashed with "kernel: add missing IR_IMON_RAW config symbol"]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-11 00:49:36 +01:00
Sergey Ryazanov
7e89421a7c ramips: add support for Zbtlink ZBT-WG1602
Zbtlink ZBT-WG1602 is a Wi-Fi router intendent to use with WWAN
(UMTS/LTE/3G/4G) modems. The router board offsers a couple of miniPCIe
slots with USB and SIM only and another one pure miniPCIe slot as well
as five Gigabit Ethernet ports (4xLAN + WAN).

Specification:

* SoC: MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB (SPI NOR)
* external watchdog (looks like Torexsemi XC6131B)
* Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* WLAN 2GHz: MT7603EN (.11n, MIMO 2x2)
* WLAN 5GHz: MT7612EN (.11ac, MIMO 2x2)
* WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios
* miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus
* WWAN Ants: detachable x4
* External storage: microSD (SDXC) slot
* USB: 2.0 Type-A port
* LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled, 1
       power indicator)
* Button: 1 (reset)
* UART: console (115200 baud)
* Power: DC jack (12 V / 2.5 A)

Additional HW information:

* SoC USB port  is shared by internal miniPCIe slot and external
  Type-A USB port, USB D+/D- lines are toggled between ports using a
  GPIO controlled DPDT switch.
* Power of the USB enabled miniPCIe slots can be individually controlled
  using dedicated GPIO lines.
* Vendor firmware feeds the external watchdog with 1s pulses. GPIO
  watchdog driver is able to either generate a 1us pulses or toggle the
  output line. 1us is not enough for the external watchod timer, so
  the line toggling driver mode is utilized.

Installation:

Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can
be directly used to install OpenWrt. Firmware must be upgraded using the
'force' and 'do not save configuration' command line options (or
correspondig web interface checkboxes) since the vendor firmware is from
the pre-DSA era.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-05 18:49:14 +01:00
Sander Vanheule
0f6b6aab2b ath79: add support for TP-Link EAP225 v1
TP-Link EAP225 v1 is an AC1200 (802.11ac Wave-1) ceiling mount access point.

Device specifications:
* SoC: QCA9563 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9882): a/n/ac, 2x2
* Ethernet (AR8033): 1× 1GbE, 802.3at PoE

Flashing instructions:
* Ensure the device is upgraded to firmware v1.4.0
* Exploit the user management page in the web interface to start telnetd
  by changing the username to `;/usr/sbin/telnetd -l/bin/sh&`.
* Immediately change the malformed username back to something valid
  (e.g. 'admin') to make ssh work again.
* Use the root shell via telnet to make /tmp world writeable (chmod 777)
* Extract /usr/bin/uclited from the device via ssh and apply the binary
  patch listed below. The patch is required to prevent `uclited -u` in
  the last step from crashing.
* Copy the patched uclited binary back to the device at /tmp/uclited
  (via ssh)
* Upload the factory image to /tmp/upgrade.bin (via ssh)
* Run `chmod +x /tmp/uclited && /tmp/uclited -u` to install OpenWrt.

uclited patching:
    --- xxd uclited
    +++ xxd uclited-patched
    @@ -53811,7 +53811,7 @@
     000d2330: 8c44 0000 0320 f809 0000 0000 8fbc 0010  .D... ..........
     000d2340: 8fa6 0a4c 02c0 2821 8f82 87c4 0000 0000  ...L..(!........
    -000d2350: 8c44 0000 0c13 461c 27a7 0018 8fbc 0010  .D....F.'.......
    +000d2350: 8c44 0000 2402 0000 0000 0000 8fbc 0010  .D..$...........
     000d2360: 1040 001d 0000 1821 8f99 8378 3c04 0058  .@.....!...x<..X
     000d2370: 3c05 0056 2484 ad68 24a5 9f00 0320 f809  <..V$..h$.... ..

To make sure the correct file is patched, the following MD5 checksums
should match the unpatched and patched files:
    4bd74183c23859c897ed77e8566b84de  uclited
    4107104024a2e0aeaf6395ed30adccae  uclited-patched

Debricking:
* Serial port can be soldered on unpopulated 4-pin header
  (1: TXD, 2: RXD, 3: GND, 4: VCC)
    * Bridge unpopulated resistors running from pins 1 (TXD) and 2 (RXD).
      Do NOT bridge the pull-down for pin 2, running parallel to the
      header.
    * Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via the LuCI web interface
    setenv ipaddr 192.168.1.1 # default, change as required
    setenv serverip 192.168.1.10 # default, change as required
    tftp 0x80800000 initramfs.bin
    bootelf $fileaddr

Tested by forum user KernelMaker.

Link: https://forum.openwrt.org/t/eap225-v1-firmware/87116
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-12-05 18:49:14 +01:00
Bjørn Mork
afeda4a3d3 realtek: sort the port list numerically
Mac adresses are assigned in the order given by the port list.  The
interfaces are also brought up in this order.  This target supports
devices with up to 52 ports.  Sorting these alphabetically is very
confusing, and assigning mac addresses in alphabetic order does not
match stock firmware behaviour.

Suggested-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-12-05 18:49:14 +01:00
Sander Vanheule
4304799b4a realtek: update watchdog timer patch
The Realtek Otto watchdog timer driver was accepted upstream, and is
queued for 5.17. Update the patch's file name, and replace by the final
version.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-12-05 18:49:14 +01:00
Oldřich Jedlička
fd4ad6cae8 x86: added support to generate VHDX images
Added support to generate dynamic-sized VHDX images for Hyper-V.
Compile-tested on x86 and run-tested on Windows 10 21H2 (Hyper-V).

Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
2021-12-05 18:49:14 +01:00
Shane Synan
9f0575a130 ipq806x: revert SDC clock changes for NBG6817 MMC
Revert the SDC "CLK_SET_RATE_GATE" changes to the SDC clock regulator
structures.

See https://elinux.org/images/b/b8/Elc2013_Clement.pdf
> if ((clk->flags & CLK_SET_RATE_GATE) && clk->prepare_count) {
>
> For this particular clock, setting its rate is possible only if the
> clock is ungated (not yet prepared)

This fixes the MMC failing to initialize on newer ZyXEL NBG6817
hardware revisions with Kingston MMC.  Older revisions should
hopefully be unaffected.

Check MMC hardware details with:
cd /sys/block/mmcblk0/device/ && \
  tail -v cid date name manfid fwrev hwrev oemid rev

Known problematic MMC names (broken before this commit):
* M62704 (dated 12/2018) via myself
* M62704 (dated 11/2018) via Drake Stefani

Known unaffected MMC names (already working without this commit):
* S10004 (dated 12/2015) via slh

Without enabling dynamic debugging, this error manifests in the kernel
hardware serial console as the following:

[    2.746605] mmc0: error -110 whilst initialising MMC card
[…trimmed other messages…]
[    2.877832] Waiting for root device /dev/mmcblk0p5...

Enabling Linux dynamic kernel debugging provides additional messages.
For guidance, see the Linux kernel documentation:
https://www.kernel.org/doc/html/latest/admin-guide/dynamic-debug-howto.html

First, enable dynamic debugging in OpenWRT's configuration:

1.  Run "make menuconfig"

2.  Select "Global build settings --->"

3.  Select "Kernel build options --->"

4.  Enable "Compile the kernel with dynamic printk" via spacebar

5.  Save and exit (arrow key to "Exit" until prompted to save, save)

Alternatively, set "CONFIG_KERNEL_DYNAMIC_DEBUG=y" in your .config.

Then, turn on dynamic debugging at boot:

Modify bootargs in
target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
to add…

bootargs = "[…existing bootargs…] dyndbg=\"file drivers/mmc/* +p\" dynamic_debug.verbose=1 loglevel=8";

For example:
 	chosen {
-		bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1";
+		bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1 dyndbg=\"file drivers/mmc/* +p\" dynamic_debug.verbose=1 loglevel=8";
 		append-rootblock = "root=/dev/mmcblk0p";

Then, compile and flash the resulting build.  If you are testing
before this commit on newer MMC hardware, be prepared to recover!

NOTE: If you have hardware serial console access, you don't need to
use TFTP recovery to change the active boot partition.

Reboot to working alternative partition via serial console:

1.  Connect to hardware serial console
    * See https://openwrt.org/toh/zyxel/nbg6817#serial

2.  Interrupt boot at "Hit any key to stop autoboot:"

3.  Run "ATSE NBG6817"

4.  Copy the result (e.g. "001976FE4B04")
    * Changes with **every boot** - can't reuse this

5.  On your local system, run
    "./zyxel-uboot-password-tool.sh <copied value here>"
    * Example: "./zyxel-uboot-password-tool.sh 001976FE4B04"

6.  Run the command provided by the password tool
    * Example: "ATEN 1,910F129B"
    * Changes with **every boot** - can't reuse this

7.  Run "ATGU"
    * You now have full u-boot shell until next boot - unlocking is
       not remembered

8.  Run either "run boot_mmc" (for booting partition set "FF") or
    "run boot_mmc_1" (for booting partition set "01")
    * These commands are not affected by dual-boot partition flags

NOTE: This will NOT set the dual-boot partition flag.  You'll need to
fix that manually.  The "nbg6817-dualboot" script may help:
https://github.com/pkgadd/nbg6817/blob/master/nbg6817-dualboot

zyxel-uboot-password-tool.sh - sourced from
commit 459c8c9ef8:

ror32() {
  echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}

v="0x$1"
a="0x${v:2:6}"
b=$(( a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ a ))
printf "ATEN 1,%X\n" $p

Kernel serial console log BEFORE commit with dynamic debug enabled:
[…trimmed…]
[    3.171343] mmci-pl18x 12400000.sdcc: designer ID = 0x51
[    3.171397] mmci-pl18x 12400000.sdcc: revision = 0x0
[    3.175811] mmci-pl18x 12400000.sdcc: clocking block at 96000000 Hz
[    3.181134] mmci-pl18x 12400000.sdcc: No vqmmc regulator found
[    3.186788] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 41,0 (pio)
[    3.192902] mmci-pl18x 12400000.sdcc: DMA channels RX dma1chan1, TX dma1chan2
[    3.215609] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 1 timing 0
[    3.227532] mmci-pl18x 12400000.sdcc: Initial signal voltage of 3.3v
[    3.247518] mmc0: clock 52000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0
[…trimmed…]
[    3.997725] mmc0: req done (CMD2): -110: 00000000 00000000 00000000 00000000
[    4.003631] mmci-pl18x 12400000.sdcc: irq0 (data+cmd) 00000000
[    4.003659] mmc0: error -110 whilst initialising MMC card
[    4.016481] mmc0: clock 0Hz busmode 2 powermode 0 cs 0 Vdd 0 width 1 timing 0

Notice how the initial clock is 52 MHz, which is incorrect - MMC
requires negotiation to enable higher speeds.

Kernel serial console log AFTER commit with dynamic debug enabled:
[…trimmed…]
[    3.168996] mmci-pl18x 12400000.sdcc: designer ID = 0x51
[    3.169051] mmci-pl18x 12400000.sdcc: revision = 0x0
[    3.173492] mmci-pl18x 12400000.sdcc: clocking block at 96000000 Hz
[    3.178808] mmci-pl18x 12400000.sdcc: No vqmmc regulator found
[    3.184702] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 41,0 (pio)
[    3.190573] mmci-pl18x 12400000.sdcc: DMA channels RX dma1chan1, TX dma1chan2
[    3.217873] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 1 timing 0
[    3.229250] mmci-pl18x 12400000.sdcc: Initial signal voltage of 3.3v
[    3.249111] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0
[…trimmed…]
[    4.392652] mmci-pl18x 12400000.sdcc: irq0 (data+cmd) 00000000
[    4.392785] mmc0: clock 52000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 1
[    4.406554] mmc0: starting CMD6 arg 03b70201 flags 0000049d
[…trimmed…]

Now, the MMC properly initializes and later switches to high speed.

Thanks to:
* Ansuel for maintaining/help with the IPQ806x platform, kernel code
* slh for additional debugging and suggestions
* dwfreed for confirming newer MMC details, clock frequency
* robimarko for device driver debug printing help, clock debugging
* Drake for testing and confirmation with their own newer NBG6817
...and anyone else I missed!

Signed-off-by: Shane Synan <digitalcircuit36939@gmail.com>
Tested-by: Shane Synan <digitalcircuit36939@gmail.com>
2021-12-05 18:49:14 +01:00
Felix Fietkau
f9a28d216d mediatek: enable bmt on mt7622-rfb1
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-12-04 22:47:17 +01:00
Chuanhong Guo
2d49e49b18 mediatek: bmt: use generic mtd api
BMT replaces nand-specific ops for erasing and writing, but the
mtk-snand driver only implements generic mtd api.

Replace erase, block_isbad, block_markbad in mtd_info for generic mtd
drivers.

Fixes: b600aee3ed ("mediatek: attach bmt to the new snand driver")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2021-12-04 22:47:17 +01:00
Yuchan Seo
c33eb0372e ramips: add support for ipTIME A3004NS-dual
ipTIME A3004NS-dual is a 2.4/5GHz band router, based on Mediatek MT7621.

Specifications:
- SoC: MT7621 (880MHz)
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
 - 2.4GHz: MT7602E
 - 5GHz : MT7612E
- Ethernet:
 - 4x LAN
 - 1x WAN
- USB: 1 * USB3.0 port
- UART:
  - 3.3V, TX, RX, GND / 57600 8N1

Installation via web interface:
- 1. Flash Initramfs image using OEM Firmware's web GUI
- 2. Boot into OpenWrt and perform Sysupgrade with sysupgrade image.

Revert to stock firmware:
- 1. Boot into OpenWrt and perform Sysupgrade with OEM Stock Firmware image.

Signed-off-by: Yuchan Seo <hexagonwin@disroot.org>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2021-12-04 09:39:11 +09:00
Pawel Dembicki
3843c641d8 kirkwood: add support for Ctera C200 V1 NAS
2-Bay NAS - maximum two 3.5" Harddisks

Hardware:
  - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz
  - Ram: 512MB (4x Nanya NT5TU128M8GE-AC)
  - NAND Flash: 256MB (Samsung 216 K9F2G08U0C)
  - Lan: 1x GBE (Marvell 88E1116R-NNC1)
  - Storage: 2x SATA HDD 3.5" Slot
  - USB: 2x USB 2.0 port
  - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND)
  - LEDs: 13x GPIO controlled
  - Buttons: 2x GPIO controlled

Known issues:
  - Buzzer is unused due lack of proper driver

Installation:
  - Apply factory initramfs image via stock web-gui.
  - Do sysupgrade to make installation complete.

Back to stock:
  - OpenWrt rootfs partition use unused space after stock firmware.
  - Full revert is possible.
  - Login via ssh and run: ctera_c200-v1_back_to_factory

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[apply sorting to device recipe]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-04 09:39:11 +09:00
Sergey V. Lobanov
e22c91e144 ramips: fix tl-mr3020-v3 switch topology to configure vlans via luci
Currently it is not possible to configure VLANs via LUCI on
tplink tl-mr3020-v3. This patch fixes switch topology for the
LUCI interface.

Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
[copied commit message from github PR]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-04 00:36:47 +01:00
Pawel Dembicki
a82fa5bcd4 ramips: mt7620: Enable PHY aneg of Lava LR-25G001
In 20b09a2125 Lava LR-25G001 router have problem with two inactive
ethernet ports. JBOOT bootloader didn't configure ethernet devices by default.
The same situation was there. It is required to enable all phy ports.
This is fragment of stock bootlog:

switch reg write_athr offset=90, value=2b0
switch reg write_athr offset=8c, value=2b0
switch reg write_athr offset=88, value=2b0
switch reg write_athr offset=84, value=2b0
switch reg write_athr offset=80, value=2b0

This patch adds proper registers configuration ar8337 initvals.
0x2b0 value causes force flow control configuration, 0x1200 was used
instead (flow control config auto-neg with phy). [1]

When switch is now ok, let's fix port numeration too.

Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")

[1] https://github.com/openwrt/openwrt/pull/4806#issuecomment-982019858

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-04 00:36:47 +01:00
Christian Lamparter
d641a60478 ipq40xx: nvmem cells for EZVIZ CS-W3-WD1200G EUP
introduce nvmem pre-cal + mac-address cells for both Wifis
and ethernet on the EZVIZ CS-W3-WD1200G EUP. This is one of
the few devices in which the correct mac adress is already
at the right place for Wifi, so no separate nvmem cell is
needed.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-04 00:36:47 +01:00
Christian Lamparter
45eb57f12f ipq40xx: unbreak EZVIZ CS-W3-WD1200G EUP on 5.10
with current images, the device is no longer booting.
It gets stuck in the bootloader with "Config not available"
and drops to the uboot shell.

|flash_type: 0
|Hit any key to stop autoboot:  0
|SF: Detected MX25L12805D with page size 4 KiB, total 16 MiB
|Config not availabale
|(IPQ40xx) #

This is because the default bootcmd "bootipq" will only read
the first four MiB of the kernel image. With 5.10 the gzip'd
kernel is slightly larger. So the part of the FIT image which
had the configuration is cut off. Hence it can't find it.

To update the bootcmd, you have to attach the serial console
again and enter the following commands into the boot prompt:

 # setenv bootcmd "sf probe; sf read 84000000 180000 600000; bootm"
 # saveenv
 # run bootcmd

This will allow booting kernels with up to six MiB. This also
allows us to drop the DEVICE_DTS_CONFIG hack we had to use.

Note:
uboot doesn't support LZMA. It fails with:
"Unimplemented compression type 3"

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-04 00:36:47 +01:00
Christian Lamparter
eb20a1b8bb gemini: only provide squashfs image for storlink-derivates
The itian sq201, raidsonic ib-4220-b and storlink sl93512r
can't boot from ext4. This is because the rootfstype in the
device-tree bootargs is set to "squashfs,jffs2". (And ext4
was not designed for raw NOR flash chips).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-04 00:36:47 +01:00
Kabuli Chana
7fd1ca96a1 mvebu: next backport mvnet MQPrio offload
linux-next MQPrio patches adding TC traffic shaping offload

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
2021-12-03 12:35:23 +01:00
Catrinel Catrinescu
24d455d1d0 ath79: add Embedded Wireless Balin Platform
Add the Embedded Wireless "Balin" platform, it is in ar71xx too
 SoC: QCA AR9344 or AR9350
 RAM: DDR2-RAM 64MBytes
 Flash: SPI-NOR 16MBytes
 WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n
 Ethernet: 3 x 10/100 Mb/s
 USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up
 PCIe: MiniPCIe - 1 x lane PCIe 1.2
 Button: 1 x Reset-Button
 UART: 1 x Normal, 1 x High-Speed
 JTAG: 1 x EJTAG
 LED: 1 x Green Power/Status LED
 GPIO: 10 x Input/Output multiplexed

The module comes already with the current vanilla OpenWrt firmware.
To update, use "sysupgrade -n --force <image>" image directly in
vendor firmware. This resets the existing configurations back to
default!

Signed-off-by: Catrinel Catrinescu <cc@80211.de>
[indent, led function+color properties, fix partition unit-address,
re-enable pcie port, mention button+led in commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-03 12:30:08 +01:00
Bjørn Mork
8ac8c09f5e ipq40xx: sysupgrade: drop disabled UBI to UBI logic
The commented out code is not required, as the comment
indicates.

The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones.  This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized.  It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-12-03 12:23:02 +01:00
Bjørn Mork
5fb51d4516 ipq806x: sysupgrade: drop unnecessary UBI to UBI logic
The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones.  This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized.  It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-12-03 12:23:02 +01:00
Bjørn Mork
25382dff85 kirkwood: sysupgrade: drop unnecessary UBI to UBI logic
The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones.  This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized.  It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-12-03 12:23:02 +01:00
Bjørn Mork
0efb169aad mvebu: sysupgrade: drop unnecessary UBI to UBI logic
The recent changes to the maximum kernel size for Mamba and Venom
highlighted the fact that the old Mamba kernel size has been
hardcoded in linksys_get_root_magic() even for devices with
a different kernel/rootfs split.

The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones.  This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized.  It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-12-03 12:23:02 +01:00
Daniel Golle
c47e82d255
mediatek: mt7623: switch to BPi-R2 to generic eMMC sysugprade
Make use of new functions in emmc.sh to implement sysupgrade on the
BananaPi BPi-R2.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-02 20:43:17 +00:00
Daniel Golle
c9db3ed58e
mediatek: mt7622: switch to generic eMMC sysupgrade
Use functions in newly introduced emmc.sh for sysupgrade of the
BananaPi BPi-R64.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-02 20:43:12 +00:00
TruongSinh Tran-Nguyen
febc2b831f
ipq40xx: add support for GL.iNet GL-B2200
This patch adds supports for the GL-B2200 router.

Specifications:
  - SOC: Qualcomm IPQ4019 ARM Quad-Core
  - RAM: 512 MiB
  - Flash: 16 MiB NOR - SPI0
  - EMMC: 8GB EMMC
  - ETH: Qualcomm QCA8075
  - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
  - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
  - WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
  - INPUT: Reset, WPS
  - LED: Power, Internet
  - UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
  - UART2: On board with BLE module
  - SPI1: On board socket for Zigbee module

Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.

What's working:
- WiFi 2G, 5G
- WPA2/WPA3

Not tested:
- Bluetooth LE/Zigbee

Credits goes to the original authors of this patch.

V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade

Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-02 20:43:07 +00:00
Alexander Couzens
8d62304785
ipq40xx: add MikroTik LHGG-60ad outdoor 802.11ad (60GHz) dish
LHGG-60ad is IPQ4019 + wil6210 based.

Specification:

- Qualcomm IPQ4019 (717 MHz)
- 256 MB of RAM (DDR3L)
- 16 MB (SPI NOR) of flash
- 1x Gbit ethernet, 802.3af/at POE IN connected through AR8035.
- WLAN: wil6210 802.11ad PCI card
- No USB or SD card ports
- UART disabled
- 8x LEDs

Biggest news is the wil6210 PCI card.
Integration for its configuration and detection has already been taken
care of when adding support for TP-Link Talon AD7200.
However, signal quality is much lower than with stock firmware, so
probably additional board-specific data has to be provided to the
driver and is still missing at the moment.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[Fix Ethernet Interface]
Signed-off-by: Nick Hainke <vincent@systemli.org>
2021-12-02 19:46:14 +00:00
Michel Promonet
fd311a5fe3 sunxi: update nanopi neo air that use brcmfmac43430a0
Update wifi firmware used for nanopi neo air, with
cypress-firmware-43430-sdio there is no wifi detected, as
brcmfmac-firmware-43430a0-sdio allow to acces to wifi.

Signed-off-by: Michel Promonet <michel.promonet@free.fr>
2021-12-02 10:58:36 +00:00
Rafał Miłecki
30b168b9b8 bcm4908: sysupgrade: refactor handling different firmware formats
This results in setting format specific data (format info, extract
commands) in a single function. It should help maintaining sysupgrade
code.

This change has been tested on Asus GT-AC5300 and Netgear R8000P.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-02 09:17:43 +01:00
Rafał Miłecki
80041dea70 bcm53xx: sysupgrade: refactor handling different firmware formats
List of supported formats grew over time and implementation got a bit
messy. There are multiple functions with format-specific parameters and
commands.

Refactor it by making platform_identify() setup all required info right
after detecting firmware format. This simplifies formats handling in
platform_other_check_image() and platform_do_upgrade() a lot.

This has been tested on:
1. SmartRG SR400ac (TRX): non-NAND sysupgrade
2. Netgear R8000 (CHK): NAND aware and standard sysupgrade-s
3. D-Link DIR-885L (Seama): NAND aware and standard sysupgrade-s
4. Luxul XWR-3150 (LXL): NAND aware and standard sysupgrade-s

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-02 09:15:18 +01:00
Rafał Miłecki
e7bd6cce4c bcm53xx: sysupgrade: simplify extracting image from Seama seal
Use "oseama extract" which supports now writing to stdout.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-12-02 09:15:18 +01:00
Aleksander Jan Bajkowski
56246f2910 lantiq: xway_legacy: disable unused switches
The xway_legacy subtarget only supports 5 devices. Most compiled
switch drivers are unused by any of these devices. The same drivers
are compiled into the xway subtarget. They were probably copied
from there when creating this subtarget.

Switches used by devices:
Arcadyan ARV4518PWR01   Realtek RTL8306SD
Arcadyan ARV4518PWR01A  Realtek RTL8306SD
Arcadyan ARV4520PW      Infineon ADM6996I
Arcadyan ARV4525PW      only PHY(IC+ IP101A)
Arcadyan ARV452CQW      Realtek RTL8306

The CONFIG_ETHERNET_PACKET_MANGLE symbol has also been disabled,
as it is only needed by the driver for AR8216.

Reduces kernel size by 19.9 kB.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2021-11-30 22:29:24 +01:00
Martin Kennedy
79ceea4303 mpc85xx: Fix HiveAP-330 nvmem mac loader
We actually need to enclose the whole section of partitions in a
`partitions { ... }` to assign it a `compatible = "fixed-partitions";
otherwise the partition referred to by `hwinfo` won't be registered
when bringing up MTD partitions, for example as per:

- <https://forum.openwrt.org/t/tp-link-c2600-missing-default-mac-mtd-partition-in-snapshot/103945/6>

- commit e2b03c16eb ("ipq806x: add missing enclosing partitions block for TP-Link C2600")'

Fixes: 8ec21d6bb2 ("mpc85xx: convert mtd-mac-address to nvmem implementation")
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[minor beautification]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-30 22:29:24 +01:00
Hauke Mehrtens
101300b842 bcm4908: Deactivate pci feature
This target does not activate CONFIG_PCI kernel configuration option, do
not activate the PCI feature. This will deactivate some PCI drivers
which are not building without PCI support in the kernel.

If PCI_SUPPORT or PCIE_SUPPORT are activated in the kernel configuration
the feature flag will be automatically set by the build system again.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-29 22:40:44 +01:00
Hauke Mehrtens
be3fcd72e9 kernel: Deactivate B53 symbols in generic configuration
Deactivate all the symbols of the B53 DSA driver in the generic kernel
configuration. Multiple targets are now using this drivers and they
only need some of the options.
This fixes the bcm4908 build which didn't deactivate all of the options.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-29 22:37:58 +01:00
Chukun Pan
001bdd5f67 sunxi: remove kmod-rtc-sunxi for unsupported devices
From driver source:

	{ .compatible = "allwinner,sun4i-a10-rtc", .data =
	&data_year_param[0] },
	{ .compatible = "allwinner,sun7i-a20-rtc", .data =
	&data_year_param[1] },

The rtc-sunxi module only supports allwinner a10 and a20 SoCs,
other SoCs in the cortexa7 and cortexa53 subtarget using the
CONFIG_RTC_DRV_SUN6I driver which is compiled into the kernel
binary, so remove this package for these unsupported devices.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2021-11-29 22:11:29 +01:00
Sander Vanheule
22f85d63cf realtek: netgear-gigabit: Add gpio-restart node
The Netgear GS110TPP v1 switch cannot reliably perform cold reboots
using the system's internal reset controller.

On this device, and the other supported Netgear switches, internal GPIO
line 13 is connected to the system's hard reset logic. Expose this GPIO
on all systems to ensure restarts work properly.

Cc: Raylynn Knight <rayknight@me.com>
Cc: Michael Mohr <akihana@gmail.com>
Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Bjørn Mork <bjorn@mork.no>
2021-11-28 22:43:08 +01:00
Sander Vanheule
3f4d6da453 realtek: Enable gpio-restart driver
Add the gpio-restart driver to the realtek build. This way devices,
which cannot reliably perform resets using the SoC's internal reset
logic, can use a GPIO line to drive the SoC's hard reset input.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-11-28 22:43:08 +01:00
Sander Vanheule
fa71139776 realtek: add missing GPIO irq properties
The internal GPIO controller on RTL838x is also an IRQ controller, which
requires the 'interrupt-controller' and '#interrupts-cells' properties
to be present in the device tree.

Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-11-28 22:43:08 +01:00
Bjørn Mork
d1464afe1b realtek: use full range of assigned MAC addresses
Some devices are assigned globally unique MAC addresses for all
ports. These are stored by U-Boot in the second U-Boot enviroment
("sysinfo") as a range of start and end address.

Use the full range if provided.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-11-28 22:43:08 +01:00
Bjørn Mork
9e7149f729 realtek: revert to "standard" management configuration
The default management interface should be easy to find for users
doing "blind" installations without console access.  There are
already multiple examples in the forum of advanced early adopters
having problems locating the management interface after installing
OpenWrt.

Requiring tagged VLAN configration to access the initial management
interface creates unnecessary hassle at best. Errors on the other
end are close to impossible to debug without console access, even
for advanced users.  Less advanced users might have problems with
the concept of VLAN tagging.

Limiting management access to a single arbitrary port among up to
52 possible LAN ports makes this even more difficult, for no
reason at all. Users might have reasons to use a different port
for management.  And they might even have difficulties using the
OpenWrt selected one. The port might be the wrong type for their
management link (e.g copper instead of fibre).  Or they might
depend on PoE power from a device which they can't reconfigure.

User expectations will be based on
- OpenWrt defaults for other devices
- stock firmware default for the device in question
- common default behaviour of similar devices

All 3 cases point to a static IP address accessible on the native
VLAN of any LAN port.  A switch does not have any WAN port.  All
ports are LAN ports.

This changes the default network configuration in line with these
expectations.

Cc: John Crispin <john@phrozen.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-28 22:33:57 +01:00
Hauke Mehrtens
889043a155 uboot-omap: Remove omap3_overo configuration
The configs/omap3_overo_defconfig file was removed from upstream U-Boot
in commit ed3294d6d1f9 ("arm: Remove overo board"). Remove it in OpenWrt
too. If someone needs this please add it also to upstream U-Boot.

This fixes the compile of the omap target.

Fixes: ffb807ec90 ("omap: update u-boot to 2021.07")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-28 22:26:27 +01:00
Hauke Mehrtens
2f6c847eb7 kernel: Add extra kernel configuration options for omap
This fixes the build on omap.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-28 19:12:53 +01:00
Felix Matouschek
1cc3b95efc ipq40xx: Add support for Teltonika RUTX10
This patch adds support for the Teltonika RUTX10.
This device is an industrial DIN-rail router with 4 ethernet ports,
2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs.

The RUTX series devices are very similiar so common parts of the DTS
are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev
board.

See https://teltonika-networks.com/product/rutx10 for more info.

Hardware:
  SoC:                 Qualcomm IPQ4018
  RAM:                 256MB DDR3
  SPI Flash 1:         XTX XT25F128B (16MB, NOR)
  SPI Flash 2:         XTX XT26G02AWS (256MB, NAND)
  Ethernet:            Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports
  WiFi 1:              Qualcomm QCA4019 IEEE 802.11b/g/n
  Wifi 2:              Qualcomm QCA4019 IEEE 802.11a/n/ac
  USB Hub:             Genesys Logic GL852GT
  Bluetooth:           Qualcomm CSR8510 (A10U)
  LED/GPIO controller: STM32F030 with custom firmware
  Buttons:             Reset button
  Leds:                Power (green, cannot be controlled)
                       WiFi 2.4G activity (green)
                       WiFi 5G activity (green)

MACs Details verified with the stock firmware:
   eth0:             Partition 0:CONFIG Offset: 0x0
   eth1:             = eth0 + 1
   radio0 (2.4 GHz): = eth0 + 2
   radio1 (5.0 GHz): = eth0 + 3
Label MAC address is from eth0.

The LED/GPIO controller needs a separate kernel driver to function.
The driver was extracted from the Teltonika GPL sources and can be
found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt

USB detection of the bluetooth interface is sometimes a bit flaky. When
not detected power cycle the device. When the bluetooth interface was
detected properly it can be used with bluez / bluetoothctl.

Flash instructions via stock web interface (sysupgrade based):
  1. Set PC to fixed ip address 192.168.1.100
  2. Push reset button and power on the device
  3. Open u-boot HTTP recovery at http://192.168.1.1
  4. Upload latest stock firmware and wait until the device is rebooted
  5. Open stock web interface at http://192.168.1.1
  6. Set some password so the web interface is happy
  7. Go to firmware upgrade settings
  8. Choose
     openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi
  9. Set 'Keep settings' to off
  10. Click update, when warned that it is not a signed image proceed

Return to stock firmware:
  1. Set PC to fixed ip address 192.168.1.100
  2. Push reset button and power on the device
  3. Open u-boot HTTP recovery at http://192.168.1.1
  4. Upload latest stock firmware and wait until the device is rebooted

Note: The DTS expects OpenWrt to be running from the second rootfs
partition. u-boot on these devices hot-patches the DTS so running from the
first rootfs partition should also be possible. If you want to be save follow
the instructions above. u-boot HTTP recovery restores the device so that when
flashing OpenWrt from stock firmware it is flashed to the second rootfs
partition and the DTS matches.

Signed-off-by: Felix Matouschek <felix@matouschek.org>
2021-11-28 18:39:01 +01:00
Matthew Hagan
67f5201276 ipq806x: add support for Cisco Meraki MR42/MR52
The MR42 and MR52 are two similar IPQ806x based devices from the Cisco
Meraki "Cryptid" series.

  MR42 main features:
  -  IPQ8068 1.4GHz
  -  512MB RAM
  -  128MB NAND
  -  2x QCA9992 (2.4 & 5GHz)
  -  1x QCA9889 (2.4 & 5GHz)
  -  1x AR8033 PHY
  -  PoE/AC power

  MR52 main features:
  -  IPQ8068 1.4GHz
  -  512MB RAM
  -  128MB NAND
  -  2x QCA9994 (2.4 & 5GHz)
  -  1x QCA9889 (2.4 & 5GHz)
  -  2x AR8033 PHYs
  -  PoE/AC power

(MR42 Only) Installation via diagnostic mode:

If you can successfully complete step 1 then you can continue to install
via this method without having to open the device. Otherwise please use
the standard UART method. Please note that when booting via TFTP, some
Ethernet devices, in particular those on laptops, will not connect in
time, resulting in TFTP boot not succeeding. In this instance it is
advised to connect via a switch.

  1. Hold down reset at power on and keep holding, after around 10 seconds
     if the orange LED changes behaviour to begin flashing, proceed to
     release reset, then press reset two times. Ensure that the LED has
     turned blue. Note that flashing will occur on some devices, but it
     will not be possible to change the LED colour using the reset button.
     In this case it will still be possible to continue with this install
     method.

  2. Set your IP to 192.168.1.250. Set up a TFTP server serving
     mr42_u-boot.mbn and
     openwrt-ipq806x-generic-meraki_mr42-initramfs-fit-uImage.itb, obtained
     from [1].

  3. Use telnet and connect to 192.168.1.1. Run the following commands to
     install u-boot. Note that all these commands are critical, an error
     will likely render the device unusable.

     Option 3.1:
       If you are sure you have set up the TFTP server correctly you can
       run this script on the device. This will download and flash the
       u-boot image immediately:

       `/etc/update_uboot.sh 192.168.1.250 mr42_u-boot.mbn`

       Once completed successfully, power off the device.

     Option 3.2:
       If you are unsure the TFTP server is correctly set up you can
       obtain the image and flash manually:

       3.2.1. `cd /tmp`
       3.2.2. `tftp-hpa 192.168.1.250 -m binary -c get mr42_u-boot.mbn`
       3.2.3. Confirm file has downloaded correctly by comparing the
              md5sum:

            `md5sum mr42_u-boot.mbn`

       3.2.4. The following are the required commands to write the image.

            `echo 1 > /sys/devices/platform/msm_nand/boot_layout
             mtd erase /dev/mtd1
             nandwrite -pam /dev/mtd1 mr42_u-boot.mbn
             echo 0 > /sys/devices/platform/msm_nand/boot_layout`

          Important: You must observe the output of the `nandwrite`
          command. Look for the following to verify writing is occurring:

            `Writing data to block 0 at offset 0x0
             Writing data to block 1 at offset 0x20000
             Writing data to block 2 at offset 0x40000`

          If you do not see this then do not power off the device. Check
          your previous commands and that mr42_u-boot.mbn was downloaded
          correctly. Once you are sure the image has been written you
          can proceed to power off the device.

  4. Hold the reset button and power on the device. This will immediately
     begin downloading the appropriate initramfs image and boot into it.

     Note: If the device does not download the initramfs, this is likely
     due to the interface not being brought up in time. Changing Ethernet
     source to a router or switch will likely resolve this. You can also
     try manually setting the link speed to 10Mb/s Half-Duplex.

  5. Once a solid white LED is displayed on the device, continue to the
     UART installation method, step 6.

Standard installation via UART - MR42 & MR52

  1. Disassemble the device and connect a UART header. The header pinout
     is as follows:

       1 - 3.3v
       2 - TXD
       3 - RXD
       4 - GND

     Important: You should only connect TXD, RXD and GND. Connecting
     3.3v may damage the device.

  2. Set your IP to 192.168.1.250. Set up a TFTP server serving
     openwrt-ipq806x-generic-meraki_(mr42|mr52)-initramfs-fit-uImage.itb.
     Separately obtain the respective sysupgrade image.

  3. Run the following commands, preferably from a Linux host. The
     mentioned files, including ubootwrite.py and u-boot images, can be
     obtained from [1].

       `python ubootwrite.py --write=(mr42|mr52)_u-boot.bin`

     The default for "--serial" option is /dev/ttyUSB0.

  4. Power on the device. The ubootwrite script will upload the image to
     the device and launch it. The second stage u-boot will in turn load
     the initramfs image by TFTP, provided the TFTP server is running
     correctly. This process will take about 13 minutes. Once a solid
     white LED is displayed, the image has successfully finished
     loading. Note: If the image does not load via TFTP, try again with
     the Ethernet link to 10Mb/s Half-Duplex.

  5. (MR42 only) Do not connect over the network. Instead connect over
     the UART using minicom or similar tool. To replace u-boot with
     the network enabled version, please run the following commands.
     Note that in the provided initramfs images, the u-boot.mbn file
     is located in /root:

     If you have not used the provided initramfs, you must ensure you
     are using an image with "boot_layout" ECC configuration enabled in
     the Kernel. This will be version 5.10 or higher. If you do not do
     this correctly the device will be bricked.

       `insmod mtd-rw i_want_a_brick=1
        mtd erase /dev/mtd8
        nandwrite -pam /dev/mtd8 /root/mr42_u-boot.mbn`

     After running nandwrite, ensure you observe the following output:

       `Writing data to block 0 at offset 0x0
        Writing data to block 1 at offset 0x20000
        Writing data to block 2 at offset 0x40000`

  6. (Optional) If you have no further use for the Meraki OS, you can
     remove all other UBI volumes on ubi0 (mtd11), including diagnostic1,
     part.old, storage and part.safe. You must not remove the ubi1 ART
     partition (mtd12).

       `for i in diagnostic1 part.old storage part.safe ; do
        ubirmvol /dev/ubi0 -N $i
        done`

  7. Proceed to flash the sysupgrade image via luci, or else download or
     scp the image to /tmp and use the sysupgrade command.

[1] The mentioned images and ubootwrite.py script can be found in this repo:
    https://github.com/clayface/openwrt-cryptid

[2] The modified u-boot sources for the MR42 and MR52 are available:
    https://github.com/clayface/U-boot-MR52-20200629

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-11-28 17:51:52 +01:00
Matthew Hagan
6e5b8c6300 ipq806x: add gsbi2_i2c label
gsbi2_i2c is used by the Meraki MR42 so we need to expose a label here.

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-11-28 17:51:52 +01:00
Matthew Hagan
771691ec83 ipq806x: backport GMAC_AHB_RESET deassert patches
Add backports of the following patches:
"net: stmmac: explicitly deassert GMAC_AHB_RESET" and
"ARM: dts: qcom: add ahb reset to ipq806x-gmac"
Required for Meraki MR42/MR52.

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-11-28 17:51:52 +01:00
Matthew Hagan
cef420e8f7 ipq806x: add GSBI nodes to ipq8064-dtsi-addidions
Rather than having separate patches for each GSBI node added, this patch
consolidates the existing GSBI1 patch into
083-ipq8064-dtsi-additions.patch. In addition, GSBI6 and GSBI7 I2C nodes,
required for the MR42 and MR52 respectively, are added.

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-11-28 17:41:18 +01:00
Robert Marko
3ad229db0b ipq40xx: add support for MikroTik hAP ac3
This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD
(hAP ac³), a  indoor dual band, dual-radio 802.11ac
wireless AP with external omnidirectional antennae, USB port, five
10/100/1000 Mbps Ethernet ports and PoE passthrough.

See https://mikrotik.com/product/hap_ac3 for more info.

Specifications:
 - SoC: Qualcomm Atheros IPQ4019
 - RAM: 256 MB
 - Storage: 16 MB NOR + 128 MB NAND
 - Wireless:
   · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
   · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae
 - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port,
             passive PoE in, PoE passtrough on port 5
- 1x USB Type A port

Installation:
1. Boot the initramfs image via TFTP
2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1"
3. Use ubiformat to remove MikroTik specific UBI volumes
* Detach the UBI partition by running: "ubidetach -d 0"
* Format the partition by running: "ubiformat /dev/mtdN -y"
Replace mtdN with the correct mtd index from step 2.
3. Flash the sysupgrade image using "sysupgrade -n"

Signed-off-by: Robert Marko <robimarko@gmail.com>
Tested-by: Mark Birss <markbirss@gmail.com>
Tested-by: Michael Büchler <michael.buechler@posteo.net>
Tested-by: Alex Tomkins <tomkins@darkzone.net>
2021-11-28 17:19:52 +01:00
John Audia
81995a5e77 kernel: bump 5.4 to 5.4.162
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*I am hit with the binutils 2.37 bug so I had to revert 7f1edbd412
in order to downgrade to 2.35.1

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-28 16:32:45 +01:00
John Audia
bbdc13b15b kernel: bump 5.4 to 5.4.161
Removed upstreamed:
    ath79/patches-5.4/921-serial-core-add-support-for-boot-console-with-arbitr.patch[1]

Manually rebased:
    layerscape/patches-5.4/804-crypto-0016-MLKU-114-1-crypto-caam-reduce-page-0-regs-access-to-.patch
    octeontx/patches-5.4/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch

All other patches automatically rebased.

1. Private email exchange with patch author, Hauke Mehrtens

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-28 16:32:45 +01:00
Christian Lamparter
a662d8550f gemini: try fis-index-block with 128 KiB sectors
Steven Maddox reported in the OpenWrt bugzilla, that his
RaidSonic IB-NAS4220-B was no longer booting with the new
OpenWrt 21.02 (uses linux 5.10's device-tree). However, it was
working with the previous OpenWrt 19.07 series (uses 4.14).

(This is still under investigation.)

Bugzilla: https://bugs.openwrt.org/index.php?do=details&task_id=4137
Reported-by: Steven Maddox <s.maddox@lantizia.me.uk>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-28 01:13:08 +01:00
Christian Lamparter
c3b9d0d1e2 ipq40xx: utilize nvmem on Netgear EX61X0 v2 Series
the Netgear EX6100v2 and EX6150v2 can utilize the nvmem
for the pre-calibration and mac-address for both WIFI
devices.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-28 01:13:08 +01:00
Christian Lamparter
297bceeecf ath79: convert TP-Link Archer C7v1/2 Wifis to nvmem-cells
For v2, both ath9k (2.4GHz Wifi) and ath10k (5 GHz) driver now
pull the (pre-)calibration data from the nvmem subsystem. v1
is slightly different as only the ath9k Wifi is supported.

This allows us to move the userspace caldata extraction
and mac-address patching for the 5GHZ ath10k supported
wifi into the device-tree definition of the device.

ath9k's nodes are also changed over to use nvmem-cells
over OpenWrt's custom mtd-cal-data property.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-28 01:13:08 +01:00
Christian Lamparter
dd7d4703e9 mpc85xx: backport "fix oops when CONFIG_FSL_PMC=n"
Martin Kennedy reported:
|Presently, I get this kernel panic on mpc85xx (Aerohive HiveAP 370)
|on OpenWrt 'master' which occurs right as the second processor is
|initialized:
|
|[    0.478804] rcu: Hierarchical SRCU implementation.
|[    0.535569] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
|[    0.627233] smp: Bringing up secondary CPUs ...
|[    0.681659] kernel tried to execute user page (0) - exploit attempt? (uid: 0)
|[    0.766618] BUG: Unable to handle kernel instruction fetch (NULL pointer?)
|[    0.848899] Faulting instruction address: 0x00000000
|[    0.908273] Oops: Kernel access of bad area, sig: 11 []
|[    0.972851] BE PAGE_SIZE=4K SMP NR_CPUS=2 P1020 RDB
|[    1.031179] Modules linked in:
|[    1.067640] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.80 
|[    1.139507] NIP:  00000000 LR: c0021d2c CTR: 00000000
|[    1.199921] REGS: c1051cf0 TRAP: 0400   Not tainted  (5.10.80)
|[...]
|[    1.758220] NIP [00000000] 0x0
|[    1.794688] LR [c0021d2c] smp_85xx_kick_cpu+0xe8/0x568
|[    1.856126] Call Trace:
|[    1.885295] [c1051da8] [c0021cb8] smp_85xx_kick_cpu+0x74/0x568 (unreliable)
|[    1.968633] [c1051de8] [c0011460] __cpu_up+0xc0/0x228
|[    2.029038] [c1051e18] [c0031bbc] bringup_cpu+0x30/0x224
|[    2.092572] [c1051e48] [c0031f3c] cpu_up.constprop.0+0x180/0x33c
|[..]
|[    2.727952] ---[ end trace 9b796a4bafb6bc14 ]---
|[    3.800879] Kernel panic - not syncing: Fatal exception
|[    3.862353] Rebooting in 1 seconds..
|[    5.905097] System Halted, OK to turn off power
|
|I bisected this down to commit 3ae5da5adc ("kernel: bump 5.10 to 5.10.80");
|that is, I don't get the panic right before this commit, but I do after.

He reported the issue upstream and Xiaoming Ni from huawei came up with
the patch (that is on it's way to upstream). While the AP370 is not in
Openwrt, this will likely affect other SMP P1020 devices OpenWrt ships
with: like the AP330, Enterasys WS-AP3710i, etc.

Reported-by: Martin Kennedy <hurricos@gmail.com>
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-28 01:13:01 +01:00
Christian Lamparter
a5b80dd487 ipq40xx: purge clk_ignore_unused bootarg
these flags have been creeping in from the QSDK.
All needed clocks should be accounted for, and
if a device is broken due to this. It should be
looked into.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-27 23:56:29 +01:00
Christian Lamparter
db7a392ade ipq40xx: update 105-ipq40xx-fix-sleep-clock.patch
Bjorn Anderson has suggestions which would help to upstream the patch.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-27 23:56:29 +01:00
Mathias Kresin
6f5c27edd4 lantiq: set maximum kernel size for P2812HNUF3
The board has a fixed size kernel partition but do not limit the kernel
size during image building.

Disable image building for both boards as well, since the kernel of the
last release as well as master are to big to fit into the 2 MByte kernel
partition.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2021-11-27 21:45:06 +01:00
Aleksander Jan Bajkowski
1c68494f67 lantiq: drop kernel 5.4 support
The current state of the kernel 5.4 support is in the openwrt-21.02
branch. No need to keep a not default used kernel in this branch.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [VRX268/ bthub5]
2021-11-27 21:45:04 +01:00
Aleksander Jan Bajkowski
2f3331ea7f lantiq: switch to kernel 5.10
Use kernel 5.10 by default.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [VRX268/ bthub5]
2021-11-27 21:40:12 +01:00
Mathias Kresin
9764968bba lantiq: ar7: use okli loader for FRITZ!Box
With Kernel 5.10 the ar7 FRITZ!Box are not booting the initramfs nor the
sysupgrade image any more. Presumably due to the grown kernel.

Use the okli preloader to workaround the bootloader issue. No solution
so far for the initramfs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2021-11-27 21:40:12 +01:00
Mathias Kresin
a328b6831c lantiq: bring back okli loader
Removed due to being unused with 1f7a03a706, but now required for the
ar7 FRITZ!Box.

Could be used for the ARV7519RW22 as well, for which the image
generation was disabled due to a stock u-boot issue with kernel bigger
than 2 MByte.

The code is combination of the ath79 and ramips okli loader.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2021-11-27 21:40:12 +01:00
John Audia
894f483d20 kernel: bump 5.10 to 5.10.82
Removed upstreamed:
    bcm53xx/patches-5.10/033-v5.16-0014-ARM-dts-NSP-Fix-mpcore-mmc-node-names.patch

Manually rebased:
    ipq806x/patches-5.10/086-ipq8064-fix-duplicate-node.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800
Run-tested: bcm2711/RPi4B, ipq806x/R7800

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-27 19:19:30 +01:00
John Audia
be077f4812 kernel: bump 5.10 to 5.10.81
Manually rebased:
    octeontx/patches-5.10/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800
Run-tested: bcm2711/RPi4B, ipq806x/R7800

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-27 19:19:11 +01:00
Sander Vanheule
f8b2bc550b realtek: Remove _machine_restart and _machine_halt
By dropping _machine_restart, users can provide more reliable or
device-specific restart modes.

_machine_halt was already removed in commit f4b687d1f0 ("realtek: use
kernel defined halt"), but quietly reintroduced in commit 8faffa00cb
("realtek: add support for the RTL9300 timer"). Let's remove it again.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:43:56 +02:00
Sander Vanheule
927570f0a3 realtek: Add and enable watchdog node
Add and enable the Realtek Otto WDT peripheral found on these SoCs.

Default all devices to use standard (cold) reboot and "soc" resets.

Devices that require the PLL value fixup before restarting, should pick
the "cpu" or "software" reset mode. These devices also need to provide a
custom reboot mode, by adding the reboot argument to the kernel command
line:

    WDT reset mode  | kernel reboot mode
    ----------------+---------------------------------------
    soc             | reboot=cold (default if not specified)
    cpu             | reboot=warm
    software        | reboot=software

Preferrably, these devices should use an alternative restart method like
gpio-restart to provide reliable restarts.

Note that watchdog restarts are not yet exposed, since the
_machine_restart override is still present.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:43:42 +02:00
Sander Vanheule
b8fc5eecdc realtek: Backport Realtek Otto WDT driver
Add patch submitted upstream to linux-watchdog and replace the MIPS
architecture symbols. Requires one extra patch for the DIV_ROUND_*
macros, which have moved to a different header since 5.10.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:43:21 +02:00
Sander Vanheule
d3a62bea08 realtek: Add Lexra bus clock
The CPU peripherals on RTL83xx/RTL930x are connected to the CPU via the
Lexra bus. This bus can provide a clock signal to these peripherals, but
no clock driver is currently available. Instead, use a fixed-clock to
provide the clock frequency, and update the dependent peripherals.

Lexra bus clock frequencies:
- RTL838x: 200MHz
- RTL839x: 200MHz
- RTL930x: 175MHz

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:42:56 +02:00
Sander Vanheule
af2cfbda2b realtek: Consolidate bootargs
All current devices use identical bootargs, so let's move that to the
common devicetree includes.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:42:44 +02:00
Sander Vanheule
72ae8314f5 realtek: reset both ethernet NIC and queues
Recent versions of Realtek's SDK reset both the ethernet NIC and queues
(SW_NIC_RST and SW_Q_RST bits) when initialising the hardware.

Furthermore, when issuing a CPU reset on the Zyxel GS1900-8 (not
supported by any current driver), the networking part of the SoC is not
reset. This leads to unresponsive network after the restart. By
resetting both the ethernet NIC and queues, networking always comes up
reliably.

Suggested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:38:43 +02:00
Rafał Miłecki
824ac6e11c bcm53xx: fix platform clocks & USB 2.0 PHY
This fixes WARNing, missing clocks and
[   10.422481] bcm_ns_usb2 1800c164.usb2-phy: Clock not defined

Fixes: 5901917b93 ("bcm53xx: use more upsteam DT patches from 5.16 / 5.17")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-23 13:49:10 +01:00
Rafał Miłecki
1d7c1a4198 bcm53xx: use new USB 2.0 PHY binding
This fixes:
[   10.440495] bcm_ns_usb2 1800c000.usb2-phy: can't request region for resource [mem 0x1800c000-0x1800cfff]
[   10.450039] bcm_ns_usb2 1800c000.usb2-phy: Failed to map DMU regs
[   10.456183] bcm_ns_usb2: probe of 1800c000.usb2-phy failed with error -16
caused by conflict in allocating resources.

Fixes: f55f1dbaad ("bcm53xx: switch to the kernel 5.10")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-23 13:49:10 +01:00
Hauke Mehrtens
cee0a95005 Revert "ath79: add support for Mikrotik LHG 5"
This reverts commit 48774decea.

This commit does not contain a valid name in the Signed-off-by line.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-23 00:45:39 +01:00
Rafał Miłecki
294fa3770b bcm53xx: specify switch ports on TP-LINK devices
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-22 15:23:22 +01:00
Daniel Golle
d6c5bb69cd
sunxi: build kernel with sun6i-rtc driver
sun6i-rtc cannot be built as a module and the hardware is only
present in some of the sunxi SoCs, see driver source:
        { .compatible = "allwinner,sun6i-a31-rtc" },
        { .compatible = "allwinner,sun8i-a23-rtc" },
        { .compatible = "allwinner,sun8i-h3-rtc" },
        { .compatible = "allwinner,sun8i-r40-rtc" },
        { .compatible = "allwinner,sun8i-v3-rtc" },
        { .compatible = "allwinner,sun50i-h5-rtc" },
        { .compatible = "allwinner,sun50i-h6-rtc" },

Set CONFIG_RTC_DRV_SUN6I=y in kernel config file for cortexa7 and
cortexa53 subtargets which covers all of the above.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-11-21 21:37:56 +00:00
Daniel Golle
148c516e1f
Revert "sunxi: add rtc-sun6i driver package"
sun6i-rtc is a builtin_platform_driver and cannot be built as a module.
Hence this reverts commit e178d9a549.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-11-21 21:29:49 +00:00
Eneas U de Queiroz
617fcd4879 ramips: fix ralink_i2s_debugfs_remove declaration
Correct ralink_i2s_debugfs_remove declaration in ralink patches when
CONFIG_DEBUG_FS is not selected.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2021-11-20 21:08:25 +01:00
Mirko Parthey
a4c3b6373c ramips: use lzma-loader on D-Link DIR-615 H1
Fixes the boot loader LZMA decompression issue:
LZMA ERROR 1 - must RESET board to recover

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
2021-11-20 21:08:25 +01:00
Thomas Aldrian
b28443f82e ramips: add support for Wavlink WL-WN576A2
This commit adds support for the Wavlink WL-WN576A2 wall-plug wireles
repeater / router. It is also sold under the name SilverCrest SWV 733 B1.

Device specs:

- CPU: MediaTek MT7628AN
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 1x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- 5 GHz: a/n/ac MT7610EN
- Buttons: WPS, reset, sliding switch (ap/repeater)
- LEDs: 5x wifi status, 1x LAN/WAN, 1x WPS

Flashing:

U-Boot launches a TFTP client if WPS button is held during boot.

- Server IP: 192.168.10.100
- Firmware file name: firmware.bin

Device will reboot automatically. First boot takes about 90s.

Coelner (waenger@gmail.com) is the original author, but I have made some
fixes. He does not wish to sign off using his real name.

Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
2021-11-20 21:08:25 +01:00
Sebastian Schaper
25df327086 ath79: merge D-Link DAP-2695 with dtsi
Further devices from the series have been added in the meantime,
introducing `qca955x_dlink_dap-2xxx.dtsi`.

Thus, merge support for DAP-2695 with the existing dtsi.

This implies factory images can now be flashed via the regular
OEM Web UI, as well as the bootloader recovery.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2021-11-20 21:08:25 +01:00
Sebastian Schaper
be88f416db ath79: move cal-data extraction to dts for DAP-2695
This device can be merged with the existing dtsi, which declares
the location of ath9k cal-data via devicetree, correcting the 2.4G
mac address in `10_fix_wifi_mac` rather than `10-ath9k-eeprom`.

To make these changes more visible, apply before merging with dtsi.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2021-11-20 21:08:25 +01:00
Sebastian Schaper
3d89685088 ath79: increase SPI frequency for D-Link DAP-2695
This device can be merged with the existing dtsi,
which will increase spi-max-frequency to 50 MHz.

To make this change more visible, increase to 50 MHz before merging.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2021-11-20 21:08:25 +01:00
Andre Heider
0aa1316218 omap: switch to kernel 5.10
Signed-off-by: Andre Heider <a.heider@gmail.com>
2021-11-20 21:08:25 +01:00
Andre Heider
d58eec88b5 omap: update kernel 5.10 config
Manually set toggles are:
MMC_SDHCI_OMAP=y
TI_PRUSS_INTC=y
DRM_TI_TPD12S015=y (successor to DRM_OMAP_ENCODER_TPD12S015 [0] [1])
DRM_DISPLAY_CONNECTOR=y (for DRM_TI_TPD12S015 [1])
DRM_SIMPLE_BRIDGE=y (for DRM_TI_TPD12S015 [1])

Manually unset toggles are:
SND_MIXER_OSS=y (disabled by generic config)

The rest was automatically modified by the kernel_oldconfig make target.

[0] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=cff5e6f7e83f6271ed75972e9a2920e2c7f62d6c
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e7e67d9a2f1dd2f938adcc219b3769f5cc3f0df7

Signed-off-by: Andre Heider <a.heider@gmail.com>
2021-11-20 21:08:25 +01:00
Andre Heider
7f5c823da2 omap: copy kernel 5.4 config for 5.10
Signed-off-by: Andre Heider <a.heider@gmail.com>
2021-11-20 21:08:25 +01:00
Jakob (Jack/XDjackieXD)
48774decea ath79: add support for Mikrotik LHG 5
The MikroTik LHG 5 series (product codes RBLHG-5nD, RBLHG-5HPnD and
RBLHG-5HPnD-XL) devices are an outdoor 5GHz CPE with a 24.5dBi or 27dBi
integrated antenna built around the Atheros AR9344 SoC.
It is very similar to the SXT Lite5 series which this patch is based
upon.

Specifications:
 - SoC: Atheros AR9344
 - RAM: 64 MB
 - Storage: 16 MB SPI NOR
 - Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2
 - Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port,
    8-32 Vdc PoE in
 - 8 user-controllable LEDs:
  - 1x power (blue)
  - 1x user (white)
  - 1x ethernet (green)
  - 5x rssi (green)

 See https://mikrotik.com/product/RBLHG-5nD for more details.

Notes:
 The device was already supported in the ar71xx target.

Flashing:
 TFTP boot initramfs image and then perform a sysupgrade. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Jakob (Jack/XDjackieXD) <jakob@chaosfield.at>
2021-11-20 21:08:25 +01:00
Zhao Yu
e178d9a549 sunxi: add rtc-sun6i driver package
AP6212 wifi need wifi_pwrseq, but from OrangePi Lite 2 dts :

wifi_pwrseq: wifi_pwrseq {
	compatible = "mmc-pwrseq-simple";
	clocks = <&rtc 1>;
	clock-names = "ext_clock";
	reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
	post-power-on-delay-ms = <200>;
};

this pwrseq need rtc clock, or kernel won't find this device.
but now rtc-sunxi.c only support A10/A20.
Orangepi Lite 2 use H6 ,from rtc-sun6i.c show compatible is
	{ .compatible = "allwinner,sun6i-a31-rtc" },
	{ .compatible = "allwinner,sun8i-a23-rtc" },
	{ .compatible = "allwinner,sun8i-h3-rtc" },
	{ .compatible = "allwinner,sun8i-r40-rtc" },
	{ .compatible = "allwinner,sun8i-v3-rtc" },
	{ .compatible = "allwinner,sun50i-h5-rtc" },
	{ .compatible = "allwinner,sun50i-h6-rtc" },
So it need this to let kernel find this mmc wifi device.

As suggested by hauke, let it build as package.

Signed-off-by: Zhao Yu <574249312@qq.com>
2021-11-20 21:08:25 +01:00
Roger Pueyo Centelles
c29f71ece7 ath79: mikrotik: enable USB module on RouterBoard wAPR-2nD
The MikroTik RouterBOARD wAPR-2nD (wAP R) router features a miniPCI-e
slot with USB lines connected, which are used by some USB cards with
miniPCI-e form factor, like the R11e-LR8. Enabling USB support is
required for such cards to work.

Tested on a MikroTik wAP LR8 kit (RB wAPR-2nD + R11e-LR8).

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2021-11-20 21:08:21 +01:00
Laurent DEBOMY
e900779e6f octeon: add USB3 support (for Ubiquiti EdgeRouter 6P)
Fixes: FS#4086

Signed-off-by: Laurent DEBOMY <laurent.debomy@canal-belletrud.fr>
2021-11-20 20:54:26 +01:00
Kabuli Chana
4580516bfb mvebu: backport mvneta basic MQPrio patch
Implement a basic MQPrio support, inserting rules in RX that translate
the TC to prio mapping into vlan prio to queues.

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
2021-11-20 20:54:26 +01:00
John Audia
c65196a48a kernel: bump 5.4 to 5.4.159
Manually rebased:
    generic-backport/850-v5.13-usb-ehci-add-spurious-flag-to-disable-overcurrent-ch.patch

All other patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-20 18:53:14 +01:00
Jianhui Zhao
43b498f669 kernel: remove non-existent config symbols
The crashlog patch as not ported to kernel 5.4.

Fixes: 4e0c54bc5b ("kernel: add support for kernel 5.4")
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
2021-11-20 18:53:14 +01:00
Mark Mentovai
0c70c5c998 mediatek/mt7622: unifi-6-lr: fix ucidef network configuration typo
There's no such thing as ucidef_set_interfaces_lan. It's
ucidef_set_interface_lan.

Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Mark Mentovai <mark@moxienet.com>
2021-11-19 18:23:25 +00:00
Rafał Miłecki
0e8a5acf6e bcm4908: build chk image for Netgear RAXE500
Fixes: 63ba3eaccd ("bcm4908: start working on Netgear RAXE500 image")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-19 14:49:18 +01:00
Rafał Miłecki
63ba3eaccd bcm4908: start working on Netgear RAXE500 image
bootfs still needs more work before it's ready.

For some unknown reason model RAXE500 uses board id RAX220.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-19 14:45:47 +01:00
Rafał Miłecki
21d28adbc1 bcm4908: enable MTD_CMDLINE_PARTS
It's needed to support devices with U-Boot. That bootloader passes MTD
layout using cmdline.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-19 14:32:58 +01:00
Rafał Miłecki
494c033f9c bcm4908: continue work on images for U-Boot based devices
It still isn't ready though - more data needs to be added to the bootfs.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-19 14:32:58 +01:00
Robert Marko
ebb6f9287e sunxi: 5.10: Orange Pi Zero Plus: Fix networking
Orange Pi Zero Plus uses a Realtek RTL8211E RGMII Gigabit PHY, but its
currently set to plain RGMII mode meaning that it doesn't introduce
delays.

With this setup, TX packets are completely lost and changing the mode to
RGMII-ID so the PHY will add delays internally fixes the issue.

It looks like this got broken in 5.10 as the PHY RGMII config got fixed
due to datasheet being available and a lot of boards got broken by that.

This has already been sent upstream and received multiple reviews.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-11-19 09:40:29 +00:00
Rui Salvaterra
3ae5da5adc kernel: bump 5.10 to 5.10.80
Deleted (upstreamed):
ath79/patches-5.10/921-serial-core-add-support-for-boot-console-with-arbitr.patch [1]
bcm53xx/patches-5.10/033-v5.15-0012-ARM-dts-BCM5301X-Fix-memory-nodes-names.patch [2]
lantiq/patches-5.10/0016-mtd-rawnand-xway-Keep-the-driver-compatible-with-on-.patch [3]
lantiq/patches-5.10/0110-MIPS-lantiq-dma-add-small-delay-after-reset.patch [4]
lantiq/patches-5.10/0111-MIPS-lantiq-dma-reset-correct-number-of-channel.patch [5]
lantiq/patches-5.10/0112-MIPS-lantiq-dma-fix-burst-length-for-DEU.patch [6]

Manually rebased:
ipq806x/patches-5.10/0065-arm-override-compiler-flags.patch

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=47462c5e600fbaffd755cd13dedd80d04e41ff83
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=2fde76df1885a6bec04317e457121326070450eb
[3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=9b366f5221d8aa64b22f35be137a5749326444ce
[4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=5af57ce8a6155fe3e4270d28d171abf8903bebc0
[5] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=b92a5df2c7adc79a57481445f67de0c1c716581f
[6] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=6b72caabc47011d03f44064452b2c65e8ed18326

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-11-19 09:40:29 +00:00
Rafał Miłecki
d745835ae1 bcm4908: backport upstream DT commits
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-18 17:51:24 +01:00
Rafał Miłecki
5901917b93 bcm53xx: use more upsteam DT patches from 5.16 / 5.17
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-11-18 16:34:55 +01:00
Aleksander Jan Bajkowski
0e561a2aea lantiq: improve ethernet performance
This commit contains a series of fixes for DMA. The burst length
patch significantly improves Ethernet performance. Patches were
tested on the xRX200 and xRX330.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2021-11-15 23:17:32 +01:00
Ansuel Smith
63ce6fcd20 kernel: fix mac-address-increment patch
Fix mac address increment patch. Permit to overflow to the next
byte and correctly calculate the incremented mac.

Reported-by: Chen Minqiang <ptpt52@gmail.com>
Fixes: d284e6ef0f ("treewide: convert mtd-mac-address-increment* to generic implementation")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-11-15 00:38:45 +01:00