Now that critical trips are defined for all thermal zones in the SOC DTSI
there is no need to duplicate them in AC and HK DTSI.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kernel 6.1 has started actually enforcing the bindings requirment that
thermal zones must have associated trips described as well, otherwise they
will fail during probing with:
[ 0.865494] thermal_sys: Failed to find 'trips' node
[ 0.867254] thermal_sys: Failed to find trip points for thermal-sensor id=4
[ 0.872271] thermal_sys: Failed to find 'trips' node
[ 0.878898] thermal_sys: Failed to find trip points for thermal-sensor id=5
[ 0.884222] thermal_sys: Failed to find 'trips' node
[ 0.890775] thermal_sys: Failed to find trip points for thermal-sensor id=6
[ 0.896073] thermal_sys: Failed to find 'trips' node
[ 0.902668] thermal_sys: Failed to find trip points for thermal-sensor id=7
[ 0.907964] thermal_sys: Failed to find 'trips' node
[ 0.914569] thermal_sys: Failed to find trip points for thermal-sensor id=8
[ 0.921203] thermal_sys: Failed to find 'trips' node
[ 0.926469] thermal_sys: Failed to find trip points for thermal-sensor id=14
[ 0.931759] thermal_sys: Failed to find 'trips' node
[ 0.938703] thermal_sys: Failed to find trip points for thermal-sensor id=15
So, since CPUFreq support isnt yet upstream we can start by adding critical
trips to all of the thermal zones to protect the devices against severely
overheating.
Qualcomm has set the overheat trip at 120 C but lets be conservative and
set it at 110 C.
This patch has been sent upstream as well.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move the Qualcomm SoC ID bindings that are used by the CPUFreq NVMEM
driver that was recently backported to generic from ipq807x as that series
depends on SoC ID bindings but they were forgotten.
Due to that IPQ806x builds would fail as the backport was still in ipq807x.
Fixes: d44279 ("generic: 6.1: backport Qualcomm CPUFreq NVMEM changes")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Recent binutils will warn if there is no .note.GNU-stack section and will
interpret that as that stack is executable.
So, lets modify the upstream 6.1 fix as in 5.15 VDSO32 and VDSO64 are still
separate but later they were merged to resolve:
/external-toolchain/openwrt-toolchain-mpc85xx-p1020_gcc-12.3.0_musl.Linux-x86_64/toolchain-powerpc_8548_gcc-12.3.0_musl/bin/../lib/gcc/powerpc-openwrt-linux-musl/12.3.0/../../../../powerpc-openwrt-linux-musl/bin/ld: warning: arch/powerpc/kernel/vdso32/getcpu.o: missing .note.GNU-stack section implies executable stack
/external-toolchain/openwrt-toolchain-mpc85xx-p1020_gcc-12.3.0_musl.Linux-x86_64/toolchain-powerpc_8548_gcc-12.3.0_musl/bin/../lib/gcc/powerpc-openwrt-linux-musl/12.3.0/../../../../powerpc-openwrt-linux-musl/bin/ld: NOTE: This behaviour is deprecated and will be removed in a future version of the linker
Signed-off-by: Robert Marko <robimarko@gmail.com>
The compilation warning was triggered by wrongly set FRAME_WARN to 1024
even for 64bit. This was recently fix by correctly setting the
FRAME_WARN to 2048 for 64bit systems.
The compilation warning would still be triggered on 32bit system but the
actual code is never reached as ARCH_USE_GNU_PROPERTY is only set on
arm64 arch.
Drop the patch as kmalloc cause perf regression as suggested by upstream
maintainers.
Fixes: fa79baf4a6 ("generic: copy backport, hack, pending patch and config from 5.15 to 6.1")
Fixes: 5913ea1ba2 ("generic: 5.15: add pending patch fixing binfmt compilation warning")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Instead of reference vlan and do strange subtraction, use the handy
struct_group() to create a virtual struct of the same size of the
members. This permits to have a more secure memset and fix compilation
warning in 6.1 where additional checks are done.
Fix compilation warning:
| inlined from 'psb6970_reset_switch' at drivers/net/phy/psb6970.c:275:2:
| ./include/linux/fortify-string.h:314:25: error: call to '__write_overflow_field'
| declared with attribute warning: detected write beyond size of field
| (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
| 314 | __write_overflow_field(p_size_field, size);
| | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|cc1: all warnings being treated as errors
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Previously, CONFIG_LZ4_DECOMPRESS=y was selected by CONFIG_RD_LZ4 only.
When building kernel for initramfs, CONFIG_RD_LZ4 will be unset by
Kernel/SetInitramfs if the chosen compression method is not lz4, then
CONFIG_LZ4_DECOMPRESS will become a *module* in the newly generated
kernel config.
However, the newly added module won't be built after
38c150612c, so packaging kmod-lib-lz4
fails due to missing lz4_decompress.ko.
CONFIG_CRYPTO_LZ4=y makes CONFIG_LZ4_DECOMPRESS=y being selected w/o
CONFIG_RD_LZ4, so that the modules of the default kernel and initramfs
kernel are consistent.
Fixes: #12766
Fixes: 38c150612c ("build: revert 54070a1 (all kernels are >= 5.10)")
Signed-off-by: Jitao Lu <dianlujitao@gmail.com>
The device already has LED push button (KEY_LIGHTS_TOGGLE)
and exported GPIO control "led-light". This commit adds
button handler script for switching on/off all device LEDs.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Most of the CPUFreq NVMEM patches have been upstreamed in an improved way.
IPQ8074 support itself is being reviewed upstream currently.
Upstreamed patches have been moved to generic backports so that ipq806x can
use them as well, so lets just use the latest version of IPQ8074 support
that is being reviewed upstream.
Runtime tested on Qnap 301W (IPQ8072A) and Xiaomi AX3600 (IPQ8071A).
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, IPQ807x is using CPUFreq NVMEM for dealing with different SoC
SKU-s having different frequency limits, and we are keeping the patches
for it in ipq807x target.
However, we managed to upstream a big cleanup of the driver in order to
make it possible for other SMEM based targets to be added to CPUFreq NVMEM.
IPQ806x will be using CPUFreq NVMEM and depends on these changes as well,
so lets put them in generic backport to avoid code duplication.
This replaces the older patches in ipq807x.
Signed-off-by: Robert Marko <robimarko@gmail.com>
MDT loader fix for remoteproc was already merged, so mark it as a backport
with the future 6.5 kernel version.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh the kernel config as multiple options were disabled in the generic
config since 6.1 was added to ipq807x.
Signed-off-by: Robert Marko <robimarko@gmail.com>
We are running out of 00xx numbers to put backports into, so lets just
renumber all of the upstreamed patches back to 0000 and onwards.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The MT7986 RFB was intended to use device tree overlays and for that
reason modified DTC_FLAGS. zyxel_ex5601-t0-stock later on probably
copied it from there. Both boards do not actually use device tree
overlays, so remove setting DTC_FLAGS from both.
The BPi-R3 does use device tree overlays, use DEVICE_DTC_FLAGS to give
it an extra 4kb of padding for overlays to be applied.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport initial LEDs hw control support. Currently this is limited to
only rx/tx and link events for the netdev trigger but the API got
accepted and the additional modes are working on and will be backported
later.
Refresh every patch and add the additional config flag for QCA8K new
LEDs support.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
If the board comes up with OpenWrt that means that the bootloader is
recent enough and knows about the new device tree overlays.
Using /etc/board.d/ is not enough in this case because it doesn't
overwrite existing configuration which may exist (and is fine to exist)
if the user updated with 'sysupgrade -F *.itb' and has kept
configuration. They would still need to manually set compat_version
even though the fact that the bootloader env has been updated can be
implied by the fact that the system has started.
Hence we can always set compat_version=1.1 for those two boards using
uci-defaults.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Sync device tree files for MT7986 boards with what landed in upstream
Linux tree to easy maintainance and also allow for a smooth update to
Linux 6.1.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that it is possible to load several device tree overlays by
appending their config names to bootconf the uImage.FIT partition
parser need to discard everything after the first '#' character in
bootconf when looking up the config node to be used.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
As the CCACHE option is already exposed, it would be helpful to also
make the ccache directory easily customizable.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
Add a variable that stores the original value of $PATH
in the host system's shell, before Make alters it.
This can be useful for when it is necessary
to ignore symlinks and programs made by the build system.
Define this new variable before all instances of
'export PATH:=' or similar.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Now that 6.1 is the default kernel, there is no reason to keep 5.15 around
as I dont plan to maintain it anymore so lets remove it.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that 6.1 kernel is working fine on ipq807x , lets switch to 6.1 as the
default kernel as its increasingly hard to keep backporting upstreamed
changes to 5.15.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport Russell King's series [1]
net: mvneta: reduce size of TSO header allocation
to pending-5.15 to fix random crashes on Turris Omnia.
This also backports two patches that are dependencies to this series:
net: mvneta: Delete unused variable
net: mvneta: fix potential double-frees in mvneta_txq_sw_deinit()
[1] https://lore.kernel.org/netdev/ZCsbJ4nG+So%2Fn9qY@shell.armlinux.org.uk/
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (squashed)
One is never to write to dev->addr directly. In 6.1 it will be a const and
with the newly enabled WERROR, we get a failing grade.
Lets fix this ahead of time.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
We are missing a bunch of headers, which trigger errors on 6.1, probably
due to changed header-in-header dependencies. Best add them now.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
The MR600v2 does not find its rootfs if it is neither directly after the
kernel or aligned to an erase block boundary (64k).
This aligns the rootfs to 0x10000 allowing the device to boot again. Based
on investigation by forum user relghuar.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Upstream DSA driver is exporting symbols with the same name as our
downstream swconfig driver, so lets rename the downstream symbols to make
them unique and avoid the conflict on 6.1 kernel.
Without this change, building 6.1 with kmod-switch-bcm53xx would conflict
with the B53 DSA driver and CI would fail.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Recent libcap versions (>= 2.60) cause problems with BPF kselftests, so
backport an upstream patch that replaces libcap and drops the dependency.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
PCK and MCK should really be P=PMIC and M=MEM, which means that they
should effectively be CLK_PMIC and CLK_ARB.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Amazon ENA network devices are also used on the
AWS Arm (Graviton) instance types, so move it from
the x86-only module file to the top level netdevices.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The SMC91X family is a ISA-age Ethernet controller.
I'm not particularly sure what it's doing in armvirt/64,
as it's unlikely there is a QEMU or real hardware configuration
that exists with it.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
These Kconfig options are required to get a screen console
working with the VMware Fusion ARM (Apple Silicon) preview.
They are likely to be the same for other Arm standard
"desktop" hardware that may emerge.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Enable SATA support, which is used by the Server Base
System Architecture reference board[1].
Signed-off-by: Anton Antonov <Anton.Antonov@arm.com>
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - https://qemu.readthedocs.io/en/latest/system/arm/sbsa.html
Also includes Advantech RSB-3720 (iMX8 Plus) support.
Signed-off-by: Anton Antonov <Anton.Antonov@arm.com>
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Re-sort into kernel config, move network into modules]
These changes are to support other vendors that have SystemReady/EFI
support, including:
* Marvell Armada
** (This is speculative as I don't have a machine of my own to test)
* Amazon Graviton (tested bare-metal and virtualized instances)
* VMware (Fusion for ARM Mac preview)
* NXP/Freescale (Layerscape series not already selected)
* HiSilicon
* Allwinner/sunxi
* Rockchip (untested, options taken from arm64 defconfig)
To give an idea of the hardware certified for SystemReady,
see
https://www.arm.com/architecture/system-architectures/systemready-certification-program/ir
and
https://www.arm.com/architecture/system-architectures/systemready-certification-program/es
Other vendors that _should_ work include Marvell Octeon 10
and Ampere. I understand these systems should work
"out of the box" in ACPI mode but may require other drivers
(e.g PCIe NICs and storage controllers).
Signed-off-by: Mathew McBride <matt@traverse.com.au>
ACPI support is required for Arm 'SystemReady' server and workstation
systems (and as an option on embedded platforms).
These config changes allow OpenWrt to boot in a QEMU virtual machine
with a UEFI/EDKII 'BIOS', but with no other hardware enabled yet.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Now that armvirt has been expanded to boot on more generic
ARM machines, remove the board and model name override.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
U-Boot with EFI boot manager functionality will store
EFI boot order data on the ESP in the ubootefi.var file.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The introduction of EFI support has changed how armvirt
images are generated. The kernel and filesystem binaries
can still be used as before with QEMU directly.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This interferes with the generation of the EFI stub section for
ARM32. As this target is not size constrained, disable the dead code
data elimination hack.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
EFI booting is used on newer machines compatible with the
Arm SystemReady specifications.
This commit restructures armvirt into a more 'generic'
target similar to x86.
See https://github.com/openwrt/openwrt/pull/4956
for a history of this port.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This set the CONFIG_FRAME_WARN option depending on some target settings.
It will use the default from the upstream kernel and not the hard coded
value of 1024 now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The omnia-medkit (only useful for installation with U-Boot
2015.10-rc2) is not being built anymore.
Now we can be reasonably sure, that there won't be first-time OpenWrt
boots with that U-Boot version, and can get rid of a rather ugly hack.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Since August 2022, users of very old Turris Omnias have been
encouraged to update U-Boot before OpenWrt installation [1].
The omnia-medkit (only useful for installation with
U-Boot 2015.10-rc2) is not needed anymore.
[1] https://openwrt.org/toh/turris/turris_omnia#installation
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
This bumps the Gemini kernel to use v6.1. While there is no
reason to stay with v5.15, I personally use newer upstream
kernels constantly and they are tested and work well. OpenWrt's
6.1 needs more time until it can be switched.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds a bunch of patches for the v6.1 Gemini kernel.
For v5.15 this was down to a single upstream patch, but for
kernel v6.2 I reworked the USB code for FOTG210, so instead of
carrying over the half-baked and incomplete patch from v5.15
I just backported all the v6.2 patches, 31 in total, as it
creates full device USB mode for e.g. D-Link DNS-313.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
When using the Gemini, we apply patches that create a single
module that support both host and device mode these days.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(move module to gemini target, keep both 6.1+2-ish + 5.15 module
CONFIG and files around until 5.15 is dropped)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
module is only useful for apm821xx targets, so
limit visability to just this target.
Fixes: 55fbcad20a ("apm821xx: make crypto4xx as a standalone module")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
commit 0c45ad41e1 changes ipq806x usb kmod name
from usb-phy-qcom-dwc3 to phy-qcom-ipq806x-usb, so
use new name.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Linux 5.19 added a feature where if there is TRIM support being advertised
on eMMC kernel will use TRIM to offload erasing to zero.
However, like always there are eMMC IC-s that advertise TRIM and kind of
work but trying to use TRIM for offloading will cause I/O errors like:
[ 18.085950] I/O error, dev loop0, sector 596 op 0x9:(WRITE_ZEROES) flags 0x800 phys_seg 0 prio class 2
So, lets utilize the kernel MMC quirks DB to disable TRIM for eMMC models
that are known to cause this.
This will fix the WRITE_ZEROES error on:
Qnap 301W which uses Micron MTFC4GACAJCN-1M
Zyxel NBG7815 which uses Kingston EMMC04G-M627
Tested-By: Enrico Mioso <mrkiko.rs@gmail.com> # NBG7815
Signed-off-by: Robert Marko <robimarko@gmail.com>
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and otherwise
identical to OrangePi R1 Plus.
Tested-by: Volkan Yetik <no3iverson@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.
Note: booting from SPI is currently unsupported, you have to install
the image on a SD card.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The set_spi_clock_speed() function is not used, this causes a compile
warning which results in a build error with -WError.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This new option (default N) will generate prompts building with OpenWrt
configs that set CONFIG_KERNEL_DYNAMIC_DEBUG=y. Fix this by adding the
disabled option to the generic config.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Not many platforms use the DRM configs but Gemini use it
so make sure to disable all new kernel v6.1 features that
we do not want to get prompted about.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebased]
Already applied in wq/for-6.5 [0].
Fixes errors in the form of:
kernel/workqueue.c: In function 'get_work_pwq':
kernel/workqueue.c:705:24: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
705 | return (void *)(data & WORK_STRUCT_WQ_DATA_MASK);
| ^
kernel/workqueue.c: In function 'get_work_pool':
kernel/workqueue.c:733:25: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
733 | return ((struct pool_workqueue *)
| ^
kernel/workqueue.c: In function 'get_work_pool_id':
kernel/workqueue.c:755:25: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
755 | return ((struct pool_workqueue *)
| ^
cc1: all warnings being treated as errors
[0] - https://lore.kernel.org/all/ZGmEmkcrfh7QdkIz@slm.duckdns.org/Fixes: #12687 ("mt7621: kernel 5.15 compile failure with GCC 13")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Import pending patches adding Ethernet support for MT7988 which are
already present in pending-5.15 also to pending-6.1.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Patches adding DSA support for MT7988 have been backported to
Linux 5.15 but not to Linux 6.1. Import backports also to Linux 6.1.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some backported patches generated with git-format-patch were not
refreshed. Use 'make target/linux/refresh' to align them with OpenWrt's
patch style.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make the crypto4xx crypto accelerator support as a standalone module.
This saves 90kb on a gzipped kernel.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In order to cut down on the Netgear WNDR4700, the ata
driver can be outsourced. This helps other apm821xx
devices too to save up on kernel size (~200 kb).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
On 6.1 swconfig is not showing up and there's a splat:
| ------------[ cut here ]------------
| WARNING: CPU: 0 PID: 1 at genl_register_family+0xb4/0x81c
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper Not tainted 6.1.29 #0
| Hardware name: Netgear WNDR4700/WNDR4720 Series APM821XX [...]
| NIP: c0599370 LR: c0599344 CTR: c08c9950
| REGS: c0c21cb0 TRAP: 0700 Not tainted (6.1.29)
| MSR: 00029000 <CE,EE,ME> CR: 48000888 XER: 00000000
|
| GPR00: c0002678 c0c21da0 c0c2cd80 [...]
| NIP [c0599370] genl_register_family+0xb4/0x81c
| LR [c0599344] genl_register_family+0x88/0x81c
| Call Trace:
| [c0c21d80] [c0c21df4] 0xc0c21df4 (unreliable)
| [c0c21e10] [c08c9988] swconfig_init+0x38/0x64
| [c0c21e30] [c0002678] do_one_initcall+0x50/0x260
This is due to it failing to register the netlink
family since changes to upstream linux in patch.
| commit 9c5d03d362519f36cd551aec596388f895c93d2d
|Author: Jakub Kicinski <kuba@kernel.org>
|Date: Wed Aug 24 17:18:30 2022 -0700
|
| genetlink: start to validate reserved header byte
this is fixed by adding the proper value to the introduced
"resv_start_op" parameter.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
it was reported that this flag caused the mx60
not to boot anymore.
Fixes: f095822699 ("apm821xx: convert legacy nand partition layou")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently, e2600ac-c1 cannot be built as the kernel is larger than the defined KERNEL_SIZE,
however, there is no bootloader limit for the kernel size so remove KERNEL_SIZE completely.
Signed-off-by: 张 鹏 <sd20@qxwlan.com>
[ improve commit title, fix merge conflict ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Convert E2600ac c2 to DSA and enable it.
Signed-off-by: 张 鹏 <sd20@qxwlan.com>
[ rename port to more generic name ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Convert E2600ac c1 to DSA and enable it.
Signed-off-by: 张 鹏 <sd20@qxwlan.com>
[ rename port to more generic name ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Management Complex (MC) userspace support is required for userspace
helpers working with DPAA2 objects exported by the Management Complex BUS.
Without it, there is the error:
```
root@OpenWrt:/# ls-addni dpmac.1
error: Did not find a device file
Restool wrapper scripts only support the latest major MC version
that currently is MC10.x. Use with caution.
error: Did not find a device file
```
This patch fixes it.
Suggested-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Add the latest default Kernel for testing.
There is no uml_watchdog userspace daemon available,
hence CONFIG_UML_WATCHDOG is disabled.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In 6.1 booting the remoteprocessor that is actually running the WLAN
unfortunatelly broke, so after a long time bisecting we managed to track it
down to commit ("soc: qcom: mdt_loader: Always invoke PAS mem_setup").
Luckily adding back the relocation check and not making an SCM call
qcom_scm_pas_mem_setup() restored the functionality.
Ansuel has sent the patch upstream.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Manually refresh tsens, PCI and CPR patches to apply and compile.
Then run automatic refresh on rest of the patches.
Signed-off-by: Robert Marko <robimarko@gmail.com>
These 3 patches have been merged upstream, so mark them as backports
along with the kernel version they have been merged into.
Signed-off-by: Robert Marko <robimarko@gmail.com>
RISC-V is a new CPU architecture aimed to be fully free and open. This
target will add support for it, based on 5.15.
Supports running on:
- HiFive Unleashed - FU540, first generation
- HiFive Unmatched - FU740, current latest generation, PCIe
SD-card images are generated, where the partitions are required to have
specific type codes. As it is commonplace nowadays, OpenSBI is used as the
first stage, with U-boot following as the proper bootloader.
Specifications:
HiFive Unleashed:
- CPU: SiFive FU540 quad-core RISC-V (U54, RV64IMAFDC or RV64GC)
- Memory: 8Gb
- Ethernet: 1x 10/100/1000
- Console: via microUSB
HiFive Unmatched:
- CPU: SiFive FU740 quad-core RISC-V (U74, RV64IMAFDCB or RV64GCB)
- Memory: 16Gb
- Ethernet: 1x 10/100/1000
- USB: 4x USB 3.2
- PCIe: - 1x PCIe Gen3 x8
- 1x M.2 key M (PCIe x4)
- 1x M.2 Key E (PCIe x1 / USB2.0)
- Console: via microUSB
Installation:
Standard SD-card installation via dd-ing the generated image to
an SD-card of at least 256Mb.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The following new common symbols are defined:
CONFIG_ARCH_FORCE_MAX_ORDER=11
# CONFIG_NET_9P_FD is not set
Removed symbols for armvirt/32 include:
CONFIG_ARM_CRYPTO=y
New symbols for armvirt/64 include:
CONFIG_ARM64_SME=y
CONFIG_CRYPTO_POLYVAL_ARM64_CE=y
# CONFIG_CRYPTO_SM4_ARM64_CE_BLK is not set
# CONFIG_CRYPTO_SM4_ARM64_NEON_BLK is not set
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The following new symbols are defined:
CONFIG_ARCH_FORCE_MAX_ORDER=11
CONFIG_CLOCKSOURCE_WATCHDOG_MAX_SKEW_US=100
CONFIG_ZBOOT_LOAD_ADDRESS=0x0
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The USXGMII driver in SDK was heavily refactored, some bugs have been
fixed and it has switched to use phylink_pcs. Follow up with changes
in SDK driver and sync our on-top-of-mainline driver with the SDK
driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use renamed build step names for all boards which were not handled by
commit c620409d58 ("mediatek: filogic: add uboot build for mt7981")
and now breaking the build.
Fixes: c620409d58 ("mediatek: filogic: add uboot build for mt7981")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: ESMT F50L1G41LB 128MB
RAM: MT5CC128M16JR-EK 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS
Power: DC 12V 1A
Flash instructions:
1. Attach UART, boot the stock firmware until
the message about failsafe mode appears.
2. Enter failsafe mode by pressing "f" and "Enter"
3. Type "mount_root", then run
"fw_setenv bootmenu_delay 3"
4. Back up all mtd partitions before flashing.
5. Reboot, U-Boot now presents a menu.
6. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
7. Select "Upgrade ATF BL2", then use this file:
openwrt-mediatek-filogic-qihoo_360t7-preloader.bin
8. Select "Upgrade ATF FIP", then use this file:
openwrt-mediatek-filogic-qihoo_360t7-bl31-uboot.fip
9. Download the initramfs image, and type "reset",
waiting for tftp recovery to complete.
a. After openwrt boots up, perform sysupgrade.
Note:
1. Since NMBM is disabled, we must back up all partitions.
2. Flash instructions is based on commit 28df7f7.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Add reserved memory for pstore/ramoops to device tree used by Linux
as well as U-Boot.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Pick accepted patches from upstream Linux tree instead of having to
maintain our slightly different downstream patches.
Import pending patch fixing I2C on MT7981 by making sure all clocks
are enabled before accessing I2C registers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In the previous commit, the kernel tag was not added when adding the
backport.
Fixes: 537624db39 ("generic: backport missing helper for phy interfaces")
Signed-off-by: Nick Hainke <vincent@systemli.org>
The function was defined before in the patch
"hack-5.15/795-backport-phylink_pcs-helpers.patch". However, the hack
did not move to 6.1. Instead of using the hack do the backport of
upstream accepted version.
Fixes errors in the form of:
make[8]: Entering directory '/home/nick/openwrt/build_dir/target-mipsel_24kc_musl/linux-ramips_mt7621/linux-6.1.29'
CC drivers/net/pcs/pcs-mtk-lynxi.o
drivers/net/pcs/pcs-mtk-lynxi.c: In function 'mtk_pcs_lynxi_config':
drivers/net/pcs/pcs-mtk-lynxi.c:160:30: error: implicit declaration of function 'phylink_get_link_timer_ns' [-Werror=implicit-function-declaration]
160 | link_timer = phylink_get_link_timer_ns(interface);
| ^~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fixes: fa79baf4a6 ("generic: copy backport, hack, pending patch and config from 5.15 to 6.1")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Make sure sub-images on the SD card are size-checked, allow
generating SD card without squashfs and/or initramfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Compex WPQ873 is a development board with two M.2 B-key
slots for cellular modems.
Device info:
- IPQ8072A SoC
- 512MiB RAM
- 256MiB NAND flash
- 8MiB SPI NOR
- 3x 1GigE ports
- 1x 2.5GigE port
- 2.4GHz/5GHz AX WLAN
- 1x USB 3.0 port
- 1x M.2 B-key socket with PCIe 3.0
- 1x M.2 B-key socket with PCIe 2.0 and USB 3.0
- 4x SIM card slots
- Bluetooth LE 5.0 (QCA4024)
Prerequisites
1) TFTP server
2) 3.3V USB to TTL cable for UART console
2.54mm pitch 4-pin header for UART is readily provided on board, no modifications are necessary to access it
TTL connector pinout: 2=TX, 3=RX, 4=GND
Arrow marks pin 1 which is 3.3V
Serial port settings: 115200 8N1 no flow control
The device will most likely ship with a QSDK-based firmware.
1. Power on device and interrupt u-boot to obtain u-boot CLI
2. set serverip to IP address of the TFTP server, for example:
`setenv serverip 192.168.1.10`
3. Download image from TFTP server:
`tftpboot 0x44000000 openwrt-ipq807x-generic-compex_wpq873-squashfs-factory.ubi`
4. Flash ubi image to both partitions and reset:
`sf probe
imxtract 0x44000000 ubi
nand device 0
nand erase 0x0 0x3400000
nand erase 0x3c00000 0x3400000
nand write $fileaddr 0x0 $filesize
nand write $fileaddr 0x3c00000 $filesize
reset`
Afterwards, you can use sysupgrade to flash new OpenWRT images.
Signed-off-by: Antti Nykänen <antti.nykanen@nokia.com>
Replace the refreshed 5.15 backports with backports for 6.1.
This fixes FMODE_CAN_ODIRECT having the same value as
FMODE_NOREUSE.
Signed-off-by: Kazuki Hashimoto <kazukih0205@gmail.com>
CONFIG_PAHOLE_HAS_SPLIT_BTF should be runtime detected as it depends on
pahole being available on the host, so filter it out of configs.
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is no reason for Octeon PCI endpoint driver to be disabled in targets
so disable it in generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is no reason for HP ProLiant HW watchdog to be disabled in individual
targets, so disable it in generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is no reason for CONFIG_ARCH_NXP to have to be disabled in individual
targets, so just disable CONFIG_ARCH_NXP in generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is no need for Surface platform drivers to be enabled by default,
especially on OpenWrt so disable CONFIG_SURFACE_PLATFORMS in the generic
config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This add basic device tree support for mediatek MT7988 SoC
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Richtek RT5190A is used on the MT7988 reference board. Backport and
enable the driver on the filogic subtarget, so we can support cpufreq
on the MT7988 reference board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add driver for the built-in 2.5G Ethernet PHY found in the MT7988 SoC.
To function the PHY also needs firmware files which have not yet been
published via linux-firmware.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update driver for MediaTek's built-in Gigabit Ethernet PHYs which can be
found in the MT7981 and MT7988 SoCs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport commits adding support for the MT7988 built-in switch to the
mt7530 driver.
This change results in the Kconfig symbol NET_DSA_MT7530 to be extended
by NET_DSA_MT7530_MDIO (everything formally covered by NET_DSA_MT7530)
and NET_DSA_MT7530_MMIO (a new driver for the MMIO-connected built-in
switch of the MT7988 SoC).
Select NET_DSA_MT7530_MDIO for all targets previously selecting
NET_DSA_MT7530, with the exception of mediatek/filogic which also
selects NET_DSA_MT7530_MMIO.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In order to support Ethernet on the MT7988 SoC add support for NETSYS v3
as well as new paths and USXGMII SerDes to the mtk_eth_soc driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds provisional pinctrl driver support for the MediaTek MT7988 SoC.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds clock drivers for the MediaTek MT7988 SoC
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This allows loading modules with large memory requirements, recently needed
while testing on armvirt/32. Past forum discussions [1] and bug reports [2]
also raised this and the ipq806x target already set it in response [3].
Given this increases kernel image size by only ~1KB, is generally useful on
multi-platform kernels, and enabled by default on upstream arm32 Linux, add
it to the generic config.
The setting has similar utility on arm64, is a requirement for KASLR, and
already enabled on most OpenWrt aarch64 targets, so pull this into the
top-level generic config.
[1]: https://forum.openwrt.org/t/vmap-allocation-for-size-442368-failed-use-vmalloc-size-to-increase-size/34545/7
[2]: https://github.com/openwrt/openwrt/issues/8282
[3]: f81e148eb6 ("ipq806x: update 4.19 kernel config").
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The identical change was previously added to the 5.15 kernel in the commit
9226f1e419 ("kernel: disable CONFIG_CPU_LITTLE_ENDIAN in generic config").
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Allow building SD card images without having both initramfs and squashfs
present on the card, just like it has already been done for the mt7622
and filogic subtargets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Refresh dts for kernel 6.1 support.
Changes:
- nbg6817 drop amba node and reference directly sdcc1.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
With 6.1 lots have changed and the platform for Makefile.boot got
dropped. Replace the patch with a new version that is alligned to the
new implementation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Update the WWAN kmods for compilation under kernel 6.1:
* Depend on kernel not being 5.10 rather than only 5.15
* Enable CONFIG_WWAN_DEBUGFS as its now optional from 5.17
* Add missing symbols for new WWAN drivers to generic config
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing symbol while adding layerscape support
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[ add commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
random_ether_addr is just a reference to eth_random_addr, that was later
dropped in more recent kernel version.
Drop random_ether_addr and use eth_random_addr directly to fix
compilation error in 6.1
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Instead of reference vlan and do strange subtraction, use the handy
struct_group() to create a virtual struct of the same size of the
members. This permits to have a more secure memset and fix compilation
warning in 6.1 where additional checks are done.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
With kernel 6.1 ieee2111_ptr is not compiled by default. Add pending
patch to restore this to make backports project compatible.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh mglru patch for new kernel version due to very fun backport
changing name from folio to pages.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh pending patches for kernel 6.1.
Changes:
- Refresh mtd patches with new implementation.
- Change 191-rtc-rs5c372-let_the_alarm_to_be_used_as_wakeup_source as
uie_unsupported got dropped and we now set the bit directly.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Zyxel EX5601-T0 specifics
--------------
The operator specific firmware running on the Zyxel branded
EX5601-T0 includes U-Boot modifications affecting the OpenWrt
installation.
Partition Table
| dev | size | erasesize | name |
| ---- | -------- | --------- | ------------- |
| mtd0 | 20000000 | 00040000 | "spi0.1" |
| mtd1 | 00100000 | 00040000 | "BL2" |
| mtd2 | 00080000 | 00040000 | "u-boot-env" |
| mtd3 | 00200000 | 00040000 | "Factory" |
| mtd4 | 001c0000 | 00040000 | "FIP" |
| mtd5 | 00040000 | 00040000 | "zloader" |
| mtd6 | 04000000 | 00040000 | "ubi" |
| mtd7 | 04000000 | 00040000 | "ubi2" |
| mtd8 | 15a80000 | 00040000 | "zyubi" |
The router boots BL2 which than loads FIP (u-boot).
U-boot has hardcoded a command to always launch Zloader "mtd read zloader 0x46000000" and than "bootm". Bootargs are deactivated.
Zloader is the zyxel booloader which allow to dual-boot ubi or ubi2, by default access to zloader is blocked.
Too zloader checks that the firmware contains a particolar file called zyfwinfo.
Additional details regarding Zloader can be found here:
https://hack-gpon.github.io/zyxel/https://forum.openwrt.org/t/adding-openwrt-support-for-zyxel-ex5601-t0/155914
Hardware
--------
SOC: MediaTek MT7986a
CPU: 4 core cortex-a53 (2000MHz)
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Micron xxx)
WIFI: Wifi6 Mediatek MT7976 802.11ax 5 GHz 4x4 + 2.4GHZ 4x4
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
1 x MaxLinear GPY211B 2.5 N-Base-T phy5 (lan4)
1 x MaxLinear GPY211B 2.5Gbit xor SFP/N-Base-T phy6 (wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
VOIP: 2 FXS ports for analog phones
MAC Address Table
-----------------
eth0/lan Factory 0x002a
eth1/wan Factory 0x0024
wifi 2.4Ghz Factory 0x0004
wifi 5Ghz Factory 0x0004 + 1
Serial console (UART)
---------------------
+-------+-------+-------+-------+-------+
| +3.3V | RX | TX | KEY | GND |
+---+---+-------+-------+-------+-------+
|
+--- Don't connect
Installation
------------
Keep in mind that openwrt can only run on the UBI partition, the openwrt firmware is not able to understand the zloader bootargs.
The procedure allows restoring the UBI partition with the Zyxel firmware and retains all the OEM functionalities.
1. Unlock Zloader (this will allow to swap manually between partitions UBI and UBI2):
- Attach a usb-ttl adapter to your computer and boot the router.
- While the router is booting at some point you will read the following: `Please press Enter to activate this console.`
- As soon as you read that press enter, type root and than press enter again (just do it, don't care about the logs scrolling).
- Most likely the router is still printing the boot log, leave it boot until it stops.
- If everything went ok you should have full root access "root@EX5601-T0:/#".
- Type the following command and press enter: "fw_setenv EngDebugFlag 0x1".
- Reboot the router.
- As soon as you read `Hit any key to stop autoboot:` press Enter.
- If everything went ok you should have the following prompt: "ZHAL>".
- You have successfully unlocked zloader access, this procedure must be done only once.
2. Check the current active partition:
- Boot the router and repeat the steps above to gain root access.
- Type the following command to check the current active image: "cat /proc/cmdline".
- If `rootubi=ubi` it means that the active partition is `mtd6`
- If `rootubi=ubi2` it means that the active partition is `mtd7`
- As mentioned earlier we need to flash openwrt into ubi/mtd6 and never overwrite ubi2/mtd7 to be able to fully roll-back.
- To activate and boot from mtd7 (ubi2) enter into ZHAL> command prompt and type the following commands:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- After rebooting check again with "cat /proc/cmdline" that you are correctly booting from mtd7/ubi2
- If yes proceed with the installation guide. If not probably you don't have a firmware into ubi2 or you did something wrong.
3. Flashing:
- Download the sysupgrade file for the router from openwrt, than we need to add the zyfwinfo file into the sysupgrade tar.
Zloader only checks for the magic (which is a fixed value 'EXYZ') and the crc of the file itself (256bytes).
I created a script to create a valid zyfwinfo file but you can use anything that does exactly the same:
https://raw.githubusercontent.com/pameruoso/OpenWRT-Zyxel-EX5601-T0/main/gen_zyfwinfo.sh
- Add the zyfwinfo file into the sysupgrade tar.
- Enter via telnet or ssh into the router with admin credentials
- Enter the following commands to disable the firmware and model checks
"zycli fwidcheck off" and "zycli modelcheck off"
- Open the router web interface and in the update firmware page select the "restore default settings option"
- Select the sysupgrade file and click on upload.
- The router will flash and reboot itself into openwrt from UBI
4. Restoring and going back to Zyxel firmware.
- Use the ZHAL> command line to manually swap the boot parition to UBI2 with the following:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- You will boot again the Zyxel firmware you have into UBI2 and you can flash the zyxel firmware to overwrite the UBI partition and openwrt.
Working features
----------------
3 gbit lan ports
Wifi
Zyxel partitioning for coexistance with Zloader and dual boot.
WAN SFP port (only after exporting pins 57 and 10. gpiobase411)
leds
reset button
serial interface
usb port
lan ethernet 2.5 gbit port (autosense)
wan ethernet 2.5 gbit port (autosense)
Not working
----------------
voip (missing drivers or proper zyxel platform software)
Swapping the wan ethernet/sfp xor port
----------------
The way to swap the wan port between sfp and ethernet is the following:
export the pins 57 and 10.
Pin 57 is used to probe if an sfp is present.
If pin 57 value is 0 it means that an sfp is present into the cage (cat /sys/class/gpio/gpio468/value).
If pin 57 value is 1 it means that no sfp is inserted into the cage.
In conclusion by default both 57 an 10 pins are by default 1, which means that the active port is the ethernet one.
After inserting an SFP pin 57 will become 0 and you have to manually change the value of pin 10 to 0 too.
This is totally scriptable of course.
Leds description
------------
All the leds are working out of the box but the leds managed by the 2 maxlinear phy (phy 5 lan, phy6 wan).
To activate the phy5 led (rj45 ethernet port led on the back of the router) you have to use mdio-tools.
To activate the phy6 led (led on the front of the router for 2.5gbit link) you have to use mdio-tools.
Example:
Set lan5 led to fast blink on 2500/1000, slow blink on 10/100:
mdio mdio-bus mmd 5:30 raw 0x0001 0x33FC
Set wan 2.5gbit led to constant on when wan is 2.5gbit:
mdio mdio-bus mmd 6:30 raw 0x0001 0x0080
Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
Specifications:
SOC: QCA9563 775 MHz + QCA9880
Switch: QCA8337N-AL3C
RAM: Winbond W9751G6KB-25 64 MiB
Flash: Winbond W25Q128FVSG 16 MiB
WLAN: Wi-Fi4 2.4 GHz 3*3 + 5 GHz 3*3
LAN: LAN ports *4
WAN: WAN port *1
Buttons: reset *1 + wps *1
LEDs: ethernet *5, power, wlan, wps
MAC Address:
use address source1 source2
label 40:9b:xx:xx:xx:3c lan && wlan u-boot,env@ethaddr
lan 40:9b:xx:xx:xx:3c devdata@0x3f $label
wan 40:9b:xx:xx:xx:3f devdata@0x8f $label + 3
wlan2g 40:9b:xx:xx:xx:3c devdata@0x5b $label
wlan5g 40:9b:xx:xx:xx:3e devdata@0x76 $label + 2
Install via Web UI:
Apply factory image in the stock firmware's Web UI.
Install via Emergency Room Mode:
DIR-859 A1 will enter recovery mode when the system fails to boot
or press reset button for about 10 seconds.
First, set computer IP to 192.168.0.5 and Gateway to 192.168.0.1.
Then we can open http://192.168.0.1 in the web browser to upload
OpenWrt factory image or stock firmware. Some modern browsers may
need to turn on compatibility mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
1. Remove unnecessary new lines in the dts.
2. Remove duplicate included file "gpio.h" in the device dts.
3. Add missing button labels "reset" and "wps".
4. Unify the format of the reg properties.
5. Add u-boot environment support.
6. Reduce spi clock frequency since the max value suggested by the
chip datasheet is only 25 MHz.
7. Add seama header fixup for DIR-859 A1. Without this header fixup,
u-boot checksum for kernel will fail after the first boot.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch enables NVMEM u-boot-env driver (COFNIG_NVMEM_U_BOOT_ENV) on
generic subtarget to use from devices, for MAC address and etc.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
read_page() need to return maximum number of bitflips instead of the
accumulated number. Change takes from upstream mt7621 u-boot [1].
* @read_page: function to read a page according to the ECC generator
* requirements; returns maximum number of bitflips
* corrected in any single ECC step, -EIO hw error
[1] https://lore.kernel.org/all/cover.1653015383.git.weijie.gao@mediatek.com/
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
the UML build fails during the kernel build:
| arch/um/drivers/net_kern.c: In function 'compute_hash':
| arch/um/drivers/net_kern.c:322:1: error: the frame size of 1072 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
| 322 | }
| | ^
|cc1: all warnings being treated as errors
The compute_hash() function is added by our patch:
102-pseudo-random-mac.patch
Instead of allocating a 1024 byte buffer on the stack for the SHA1
digest input, let's allocate the data on the heap. We should be
able to do that since crypto_alloc_ahash and ahash_request_alloc
also need to allocate structures on the heap.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The PHY name has been changed to "mt7530-0" since IRQ support
was added to MT7530 driver.
Fixes: f9cfe7af1f ("kernel: backport MT7530 IRQ support")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
(node names, added color, function+function-enumerator properties)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The Sophos SG/XG-135 revision 3 has odd numbering of eth ports
where the WAN port (as marked on the case) is:
`eth6` and `eth0`, `eth1`, `eth2`, `eth3`, `eth5`, `eth7`, `eth8` are LAN ports.
Port `eth4` seems to be the SFP port.
Also add the missing LED definition for supported Sophos devices.
Original discussion at:
https://forum.openwrt.org/t/openwrt-on-revision-3-of-sophos-desktop-appliances/152912
Signed-off-by: Stan Grishin <stangri@melmac.ca>
Iomega Storcenter ix4-200d is a four-bay SATA NAS powered by a Marvell
Kirkwood SoC clocked at 1.2GHz. It has 512MB of RAM and 32MB of
flash memory, 3x USB 2.0 and 2x 1Gbit/s NIC
Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1200Mhz
- Flash size: 32 MiB
- RAM: 512MB
- LAN: 2x 1Gbit/s
- 3x USB 2.0
Notes:
- The blue drive LED is triggered by HDD activity, it can not be controlled
via GPIO.
- The LCD screen requires proprietary code and does not function at this time.
- Due to a kernel-related issue with the Marvell 88SE6121 SATA controller,
currently only trays numbered #3 and #4 work, #1 and #2 do not. [1]
Serial pinout:
CN4
--------------
| 10 8 6 4 2 |
| 9 7 5 3 1 |
-------------- PIN 1 Mark (fat line)
1 = RXD
4 = TXD
6 = GND
9 = 3.3V (not necessary to connect)
Installation instructions:
1. download initramfs-uImage and copy into tftp server
2. connect the tftp server to network port #1
3. access uboot environment with serial cable and run
setenv mainlineLinux yes
setenv arcNumber 1682
setenv console 'console=ttyS0,115200n8'
setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
setenv bootargs_root 'root='
setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
saveenv
setenv serverip 192.168.1.1
setenv ipaddr 192.168.1.2
tftpboot 0x00800000 [initramfs-uImage filename]
bootm 0x00800000
4. connect to LAN on network port #2, log into openwrt and sysupgrade to install into flash
[1] https://bugzilla.kernel.org/show_bug.cgi?id=216094
Signed-off-by: Sander van Deijck <sander@vandeijck.com>
(aligned FROM from signed-off. LED+key rename, whitespace removal)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This removes unneeded kernel version switches from the targets after
kernel 5.10 has been dropped.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Recently, a strange variant of ZTE MF286 was discovered, having QCA9886
radio instead of QCA9882 - like MF286A, but having MF286 flash layout
and rest of hardware.
To support both variants in one image, bind calibration data at offset
0x5000 both as "calibration" and "pre-calibration" nvmem-cells, so
ath10k can load caldata for both at runtime.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Specifications
The D-Link EXO AC1750 (DIR-869) router released in 2016.
It is powered by Qualcomm Atheros QCA9563 @ 750 MHz chipset, 64 MB RAM and 16 MB flash.
10/100/1000 Gigabit Ethernet WAN port
Four 10/100/1000 Gigabit Ethernet LAN ports
Power Button, Reset Button, WPS Button, Mode Switch
Flashing
1. Upload factory.bin via D-link web interface (Management/Upgrade).
Revert to stock
Upload original firmware via OpenWrt sysupgrade interface.
Debricking
D-Link Recovery GUI (192.168.0.1)
Signed-off-by: Jan Forman <forman.jan96@gmail.com>
For D-link DIR-859 and DIR-869
Replace the mtd-cal-data by an nvmem-cell.
Add the PCIe node for the ath10k radio to the devicetree.
Thanks to DragonBlue for this patch
Signed-off-by: Jan Forman <jforman@tuta.io>
gpio-export for the switch reset pin replaced with a reset pin definition for the driver, within the phy node.
Signed-off-by: Jan Forman <forman.jan96@gmail.com>
Tested-By: Sebastian Schaper <openwrt@sebastianschaper.net>
The 'KERNEL' is not referenced by other objects, so double '$$' will
cause shell unable to parse the variable 'BLOCKSIZE':
dd ... bs=$(BLOCKSIZE) conv=sync
bash: line 1: BLOCKSIZE: command not found
Fixes: 09a0efbe83(ramips: set default BLOCKSIZE to 64k for nor flash devices)
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Replace the fall through comment with fallthrough; in the ar2315 flash
driver.
This fixes a compile warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of defining an own virt_to_phys() use the version from the
generic MIPS arch code which does the same.
This fixes a compile warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use same logic as in append-metadata so build doesn't fail in case of
missing build-key (it was previously failing on the buildbot runners).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kernel 5.15.111 includes backport of commit
("firmware: qcom_scm: Clear download bit during reboot") which is causing
reboot on ipq40xx to stop working, more precisely the board will hang after
reboot is called with:
root@OpenWrt:/# reboot
root@OpenWrt:/# [ 76.473541] device lan1 left promiscuous mode
[ 76.474204] br-lan: port 1(lan1) entered disabled state
[ 76.527975] device lan2 left promiscuous mode
[ 76.530301] br-lan: port 2(lan2) entered disabled state
[ 76.579376] device lan3 left promiscuous mode
[ 76.581698] br-lan: port 3(lan3) entered disabled state
[ 76.638434] device lan4 left promiscuous mode
[ 76.638777] br-lan: port 4(lan4) entered disabled state
[ 76.978489] qca8k-ipq4019 c000000.switch wan: Link is Down
[ 76.978883] device eth0 left promiscuous mode
[ 76.987077] ipqess-edma c080000.ethernet eth0: Link is Down
[
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00123
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Reset status Config, 0x00000010
S - Core 0 Frequency, 0 MHz
B - 261 - PBL, Start
B - 1339 - bootable_media_detect_entry, Start
B - 1679 - bootable_media_detect_success, Start
B - 1693 - elf_loader_entry, Start
B - 5076 - auth_hash_seg_entry, Start
B - 7223 - auth_hash_seg_exit, Start
B - 578349 - elf_segs_hash_verify_entry, Start
B - 696356 - PBL, End
B - 696380 - SBL1, Start
B - 787236 - pm_device_init, Start
D - 7 - pm_device_init, Delta
B - 788701 - boot_flash_init, Start
D - 52782 - boot_flash_init, Delta
B - 845625 - boot_config_data_table_init, Start
D - 3836 - boot_config_data_table_init, Delta - (419 Bytes)
B - 852841 - clock_init, Start
D - 7566 - clock_init, Delta
B - 864883 - CDT version:2,Platform ID:9,Major ID:0,Minor ID:0,Subtype:64
B - 868413 - sbl1_ddr_set_params, Start
B - 873402 - cpr_init, Start
D - 2 - cpr_init, Delta
B - 877842 - Pre_DDR_clock_init, Start
D - 4 - Pre_DDR_clock_init, Delta
D - 13234 - sbl1_ddr_set_params, Delta
B - 891155 - pm_driver_init, Start
D - 2 - pm_driver_init, Delta
B - 909105 - Image Load, Start
B - 1030210 - Boot error ocuured!. Error code: 303d
So, until a proper fix is found, lets revert the culprit patch to have
reboot working again.
Fixes: 228e0e1039 ("kernel: bump 5.15 to 5.15.111")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Manually adjusted before running quilt due to new location in tree:
backport-5.15/780-v5.16-bus-mhi-pci_generic-Introduce-Sierra-EM919X-support.patch
backport-5.15/781-v6.1-bus-mhi-host-always-print-detected-modem-name.patch
pending-5.15/790-bus-mhi-core-add-SBL-state-callback.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Signed-off-by: John Audia <therealgraysky@proton.me>
The NanoPi R2C is a minor variant of NanoPi R2S with the on-board NIC
chip changed from rtl8211e to yt8521s, and otherwise identical to R2S.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The bootscript for nanopi r2s/r4s only changes the serial address, so
make it auto detected in mmc bootscript rather than creating more
(redudant) files.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
should have been part of the ipq-wifi update.
Fixes: 8217f02a1c ("ipq-wifi: drop upstreamed board-2.bin")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add a ventana-img.gz compressed disk image to support
squashfs+ext4 on a block storage device such as USB/MMC/SATA.
The Ventana bootloader expects the bootscript to be
boot/6x_bootscript-ventana therefore we must create a bootfs
that matches this.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
These same codes are repeated for many devices now, it's better to
move them to shared definition. This commit also add the missing
KERNEL_SIZE of the ZyXEL NR7101 and ZyXEL LTE3301-PLUS.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
In kernel 5.15, the default erase sector size of the nor flash has
been switched from 4k to 64k. This may cause the configuration not
be preserved across upgrades. To avoid this issue, change the default
BLOCKSIZE to 64k.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Make use of minor sector size (4k) on supported flash chips to improve
spi read/write performance.
Tested on ramips/mt7628: Motorola MWR03
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The BDFs for the:
Aruba AP-365
Devolo Magic 2 WiFi next
Edgecore ECW5410
Edgecore OAP100
Extreme Networks WS-AP3915i
GL.iNet GL-A1300
GL.iNet GL-AP1300
GL.iNet GL-S1300
Linksys EA8300
Linksys WHW03v2
Nokia Wi4A AC400i
P&W R619AC
Pakedge WR-1
Qxwlan E2600AC C1
Sony NCP-HG100/Cellular
Teltonika RUTX10
ZTE MF18A
were upstreamed to the ath10k-firmware repository
and landed in linux-firmware.git.
Furthermore the BDFs for the:
8devices Habanero
8devices Jalapeno
Qxwlan E2600AC C2
have been updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Use <mdio>:<addr>:<speed> trigger instead of netdev(link) trigger for
Fortinet FortiGate 50E, to indicate link speed on the each phys.
1000 Mbps: Green
100 Mbps : Amber
10 Mbps : (turn off)
Fixes: 102dc5a625 ("mvebu: add support for Fortinet FortiGate 50E")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To use <mdio>:<addr>:<speed> trigger for LEDs, enable PHY LED trigger
(CONFIG_LED_TRIGGER_PHY).
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Enable BLK_DEV_SD and USB_STORAGE so that rootfs can be on a USB Mass
Storage device.
This increases the kernel Image by 66KiB
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable BLK_DEV_SD and USB_STORAGE so that rootfs can be on a USB Mass
Storage device.
This adds 23KiB to the compressed kernel size
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
support for MR18 and MR26 was developped before
the userspace nu801 was integrated with x86's
MX100 into OpenWrt. The initial nu801 + kmod-leds-uleds
caused build-bot errors.
The solution that worked for the MX100 was to include
the kmod-leds-uleds to the device platform module.
Thankfully, the MR26 and MR18 can just add the uleds
package to the DEVICE_PACKAGES variable.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Rename Newifi D2 to D-Team Newifi D2, and Newifi D1 to Lenovo Newifi D1.
Let's not make naming exceptions because of marketing whims.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
The TOZED ZLT S12 PRO is an AC1200 router featuring 4 Ethernet ports with a
TOZED TL70-C cellular modem which supports the NCM mode.
The stock firmware does SIM locking on the modem by stopping dialing when a
different PLMN is detected. This is not the case on OpenWrt.
Specifications:
- CPU: MediaTek MT7621AT
- RAM: 256MB DDR3
- NOR Flash: MX25L12833FM2I 16MB SPI Flash
- Wi-Fi 2.4Ghz: MT7603E
- Wi-Fi 5Ghz: MT7612E
- Switch: MT7530 4x 1Gbit Ports
- WWAN: Unisoc SL8563 based TOZED TL70-C LTE CAT6 cellular modem
- USB: 1x optional USB2.0 external port
- Switches/Buttons: WPS, Reset, Power Switch
- LEDs: Power, Wi-Fi, Data, Signal 1-5, Phone
Installation and TFTP Recovery:
- Connect to serial console.
- Boot initramfs image by choosing option 1 when U-Boot prompts.
- Install sysupgrade image via OpenWrt.
Serial Pins:
Located at the bottom right when looking from the front, right under the
Reset/WPS buttons. The pinout from the left is:
- RX
- GND
- TX
Baudrate is 115200.
When connecting from a powered off state, disconnect RX as it blocks the
boot process.
Link: http://www.sztozed.com/en/contents/58/84.html
Co-developed-by: Andre Cruz <me@1conan.com>
Signed-off-by: Andre Cruz <me@1conan.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
When adding support for the GL.iNet GL-MT3000 a reference to the
non-existent make_gl_metadata.py script was accidentally added.
Remove it, flashing from vendor firmware also works fine without that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
16MB SPI-NOR (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V
[LEDS] VCC-GND-RX-TX [ETH]
Header is located below the heatsink
Case
----
Unscrew the 4 bottom screws. Remove the top of the case by inserting a
small screwdriver into the ventilation holes and lift the top cover.
This works best by beginning near the ETH-ports. The top is clipped on
the front near the LEDs with two plastic clips. The back has a single
clip in the middle. Start at one of the back edges.
MAC-Addresses
-------------
80:AF:CA:00:F9:C6 LAN
80:AF:CA:00:F9:C7 WAN
80:AF:CA:00:F9:C6 W2
82:AF:CA:30:F9:C6 W5
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device. Keep pressing the "0" key to enter the U-Boot
shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.2. Rename the image to "cudy3000.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Note: Cudy does not yet provide a image for disabling their
signature-protection. This has happened in the past. Make sure to check
the wiki for a possible easier installation method.
Signed-off-by: David Bauer <mail@david-bauer.net>
Import patch to prevent crashes in case WO firmware is missing on devices
with only a single frontend (eg. MT7981+MT7976).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Following 5264296, Mirotik NAND devices now use yafut to flash the
kernel on devices. This method is incompatible with the old-style
"kernel2minor" flash mechanism.
Even though NAND images were disabled in default build since 21.02, a
user flashing a new-style image onto an old-style image would result in
in a soft-brick[1]. In order to prevent such accidental mishap,
especially as these device images will be reenabled in the upcoming
release, bump the compat version.
After the new image is flashed, the compat version can be updated:
uci set system.@system[0].compat_version='1.1'
uci commit
[1] https://github.com/openwrt/openwrt/pull/12225#issuecomment-1517529262
Cc: Michał Kępień <openwrt@kempniu.pl>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Refresh patches to make them cleanly apply.
This problem was found by the github CI.
Fixes: ecd9abc8c0 ("kernel: use upstream firmware patch for Broadcom's NVRAM")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It has just been queued for the v6.5. It allows Ethernet drivers to read
MACs from NVRAM using NVMEM interface.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
