This backport patch inserted suspend/resume callbacks
for the wrong PHY driver.
The fixed patch is needed for Huawei AP5030DN
to initialize its second PHY.
Refresh all affected patch with make target/linux/refresh.
Fixes: 06cdc07f8c ("ath79: add support for Huawei AP5030DN")
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/17312
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sets openwrt,netdev-name for the gmac nodes in the dts of BPI-R4 which
correspond to the two sfp slots. By default they are automatically
named as eth1 and eth2 in bad order, however 'SFP1-WAN' and 'SFP2-LAN'
are printed on the PCB and the official metal case has labels 'SFP-WAN'
and 'SFP-LAN'. Thus, label the ports accordingly to match the
board/case labels.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Sets openwrt,netdev-name for the gmac1 node in the dts of BPI-R3, which
corresponds to the sfp1 slot, to have a proper naming and match the
label on the official BPI-R3 metal case. This renames the port from eth1
to sfp1.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Add support in filogic subtarget for our own custom property
`openwrt,netdev-name` in the device tree instead of `label` for
renaming interfaces. This was suggested upstream to avoid potential
conflicts [1].
[1] https://lore.kernel.org/netdev/20240709124503.pubki5nwjfbedhhy@skbuf/
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
access to undeclared variable radio In [anonymous function](), file /usr/share/hostap/hostapd.uc, line 830, byte 45:
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Userspace handling is deprecated. MAC address stuff needs to remain
handled in userspace as it's encrypted. Maybe an NVMEM driver can be
written in the future...
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17276
Signed-off-by: Robert Marko <robimarko@gmail.com>
e00958884416 fw4: do not add physical devices for soft offload
dfbcc1cd127c fw4: skip not existing netdev names in flowtable device list
18fc0ead19fa init: use the reload data trigger to reload firewall on procd data changes
Fixes: https://github.com/openwrt/openwrt/issues/13410
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently if the host system has cmocka installed it will leak the host
path and try to use the host cmocka and build tests.
This will obviously fail, so backport upstream commit allowing disabling
of tests and disable building them.
Fixes: openwrt/packages#25456
Link: https://github.com/openwrt/openwrt/pull/17297
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add QCA2066 firmware package, ath11k is already supported.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17260
Signed-off-by: Robert Marko <robimarko@gmail.com>
The qusb_phy node looks for the following supply:
"vdd", "vdda-pll", "vdda-phy-dpdm"
And ssphy node looks for the following supply:
"vdda-phy", "vdda-pll"
So fix the usb regulator supply for RT-AX89X.
Fixes: 1306237 ("qualcommax: use PHY regulator for USB GPIO")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17290
Signed-off-by: Robert Marko <robimarko@gmail.com>
93461ca4c827 unet-cli: only apply defaults on create
3e5766783d5d unet-tool: add support for confirming password
074d3659ca4a unet-cli: confirm password when creating new seed based key
bf3488a3807a unet-cli: add add/set-local-host command
9eb57c528461 unet-cli: add support for setting interface zone
a0a2d80f3459 ubus: add firewall rules for network port/pex_port via procd
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2e206dbe77ec service: add support for triggers on service/instance data changes
735b48728fca service: remove leftover lines from previous commit
32469644a029 service: allow incremental changes to service properties
fd01fb852302 service: fix double free bug when dealing with data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
058a099f5bc5 interface: fix memleak and reload issue for the zone attribute
ea01ed41f321 interface: remove unnecessary NULL checks before free()
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Not all Kirkwood systems have the Marvell MV88E6XXX switches.
Drop those from the generic config and add them as modules
in the systems that have it.
This was inferred by inspecting the upstream DTS files for any
mv88e* strings and adding the mv88e6xxx kmod package to those
that have an upstream device tree with an MV88E6xxx switch
and an OpenWrt image target.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
d22d7db581d5 bpf_skb_utils.h: add missing include to fix build against newer kernel headers
bbd3e0eb1419 host: fix peer routes on a node acting as gateway
b17164751fc7 unet-tool: add support for generating keys from salt + seed passphrase
041e05870c20 unet-tool: add support for dumping pubkey from signed file
b58920d420cb unet-tool: add support for extracting network data from signed bin file
f335f5b40b4e unet-cli: add support for generating key from seed
8b1f1d099352 unet-cli: add support for importing networks from signed data
188ba05eadf2 unet-cli: add missing command line help for import
8f15fc306a40 unet-cli: fix add-ssh-host with seed keys
486bc3b86dc2 pex-msg: enable broadcast for global PEX socket
e4a24cdfbc1c unet-cli: fix defaults on create
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is using mac-base and so a 0 needs to be added.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17274
Signed-off-by: Robert Marko <robimarko@gmail.com>
Images for xrx200 8M flash are either not building due to image
size (TD-W8970, TD-W8980) or building such that the available
free space in the overlayfs is too little to be useful.
To keep images for these devices buildable, move them into a
small flash variant of the xrx200 subtarget. As these devices
are NOR flash only, remove NAND and UBI references from the
kernel config to gain some additional image size reduction.
The apparent 8M flash devices Arcadyan VGV7510KW22-brn,
Arcadyan VGV7519-brn and Lantiq Easy80920-nor seem to exist in
order to create special "factory" installation images for these
devices (which actually have larger flash: 16MB for the
Arcardyan devices; 64MB for the Lantiq device). As a
considerable amount of surgery would appear to be required to
the uboot-lantiq package structure to separate the "factory"
from the "sysupgrade" device recipes for these devices they
remain in the xrx200 target - if factory images aren't now
created, 23.05.x factory images should suffice for initial
installation.
Tested on: Netgear DM200, TP-Link TD-W8980,
AVM Fritz7490 (xrx200 subtarget: image build only)
Fixes: https://github.com/openwrt/openwrt/issues/16761
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
Link: https://github.com/openwrt/openwrt/pull/17113
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes "sh: write error: Invalid argument" for all default!=1 LEDs
as an empty $brightness was used.
Setting up LEDs via luci also now works again.
Fixes cbdfd03e: "base-files: add option to set LED brightness"
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/issues/17269
Signed-off-by: John Crispin <john@phrozen.org>
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.65
Update to checksum only/no patches required a rebase.
Per the changelog, this is a trivial upstream bump with only 4
commits, 2 of which being reverts.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17217
Signed-off-by: Robert Marko <robimarko@gmail.com>
The PHY can handle turning off the GPIOs when turning off all USB ports.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17192
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- Device: ASUS 4g-AX56
- SoC: MT7621AT
- Flash: 128MB
- RAM: 512MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LTE : Fibocom FG621-EA
- LEDs: 1x POWER (white, configurable)
1x 2.4G (white, not configurable)
1x 5G (white, not configurable)
1x WAN (white, not configurable)
1x 3G/4G (white, not configurable)
3x signal (white, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.0.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.0.1
Input TFTP server's IP address: 192.168.0.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_4g-ax56-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Notice:
- LTE module is disable after flash openwrt image so you must active LTE by following two AT command
echo -e "AT+GTAUTOCONNECT=1\r\n" > /dev/ttyUSB0
echo -e "AT+GTRNDIS=1,1\r\n" > /dev/ttyUSB0
- After finish AT command once, you don't need to input command later even if reboot/restore default
Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16752
Signed-off-by: John Crispin <john@phrozen.org>
Hardware
* Mediatek MT7620A + Mediatek MT7610EN
* 64MB RAM
* 8MB NAND (Winbond 25064FVSIG )
Both 2.4GHZ and 5GHZ are working, it is enabled by default since there is no
physical ethernet port in the device.
All LED's and buttons work.
UART: 57600 8N1 3.3V
Installation
Upload the openwrt-ramips-mt7620-trendnet_tha103ac-initramfs-kernel.bin via
the manufacturer firmware upgrade page on the device.
Upon reboot wait +- 3 mins until the green power LED is not flashing anymore
(do not be tempted to switch the device off while the LED is flashing, unless
you are ready for soldering and TTL) and then press the WPS button to enable
the default OpenWrt Wifi AP, the BLUE wifi LED will start flash.
Then install openwrt-ramips-mt7620-trendnet_tha103ac-squashfs-sysupgrade.bin
via OpenWrt.
The integrated power monitoring and relay do not work in OpenWrt as the PL7223
chip source/documentation is unavailable.
Recovery
Mis-configuration can be dealt with using the RESET button to reset to factory,
worst case scenario will require some serious work and soldering, there's pads
on the PCB for both the UART and ETH0, and I soldered and tested that it does
work.
You will have to power the board using the header pins GND & 5V, see the 8-pin
header socket.
Signed-off-by: Die Peter Pan <diepeterpan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17114
Signed-off-by: John Crispin <john@phrozen.org>
The original ar71xx version of this device used 1002 as mac address for
both ethernet and wireless. The ath79 version inexplicably changes this
to 2, which seems to be done nowhere else in ath79, indicating it's
bogus.
Restore previous ar71xx assignment. 1002 is used as an ethernet
interface with some other devices as well.
Also remove the bogus caldata userspace extraction. The size is bogus
and it's already handled in dts.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17083
Signed-off-by: John Crispin <john@phrozen.org>
NRadio C8-668GL is a Wi-Fi 6 5G cellular router based on MediaTek MT7981B SoC.
- **SoC**: MediaTek MT7981B (2x Cortex-A53, 1.3GHz)
- **RAM**: Nanya NT5AD512M16C4-JR 1GB DDR4
- **Flash**: ESMT FC51L08SFY3A 8GB eMMC
- **Ethernet**:
- 1x 2.5GbE (via GMAC0 and GPY211 PHY, shared with MT7531AE)
- 3x 10/100/1000 Mbps (via MT7531AE, connected to GMAC0)
- 5G Modem: GMAC1 (via GPY211 PHY - RTL8125BG - RM520N-GL)
- **Wi-Fi**: MediaTek MT7976CN (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000)
- **Buttons**: Reset, WPS
- **LEDs**: Power, 5G, 4G, WiFi
- **SIM Slot**: 1x Nano SIM
- **5G Modem**: Quectel RM520N-GL (Snapdragon™ X62)
- **Power**: 12V/2A DC, 5.5×2.1 connector
The MAC addresses are derived from the `fac_mac` field in the `bdinfo` partition, formatted as `fac_mac = HWMAC`. The allocation is as follows:
| Vendor | OpenWrt Interface | Address | Notes |
|---------|-------------------|---------------|------------------------------------------------|
| LAN | br-lan | Label MAC | Default |
| WAN | lan4 | Label MAC+1 | Only when lan4 is switched to WAN |
| 2.4GHz | phy0-ap0 | Label MAC | |
| 5GHz | phy1-ap0 | Label MAC | (Local Admin bit set) |
| Modem | eth1 | Label MAC+2 | |
1. Log in to the router via `http://192.168.66.1`/.
2. Upgrade the official firmware to dual-system mode.
3. Select **Burn second system** and upload the `sysupgrade.bin` image.
- Download the image from the OpenWrt build system or build it yourself using the OpenWrt buildroot.
4. Wait for 30 seconds and click **Switch system**.
5. The device will reboot and switch to OpenWrt.
Set the U-Boot environment variable `boot_system=0` and reboot:
```bash
fw_setenv boot_system 0
```
Power off the router, hold the **WPS button**, and power it back on.
1. Rename the stock firmware file to **`recovery.bin`**.
2. Set your PC's Ethernet IP to **192.168.1.88** and connect it to the lan1 port on the router.
3. Run a TFTP server and place the `recovery.bin` file in its root directory.
4. Power off the router, press and hold the **Reset button**, and power it back on.
5. Release the Reset button when the TFTP server shows activity.
6. Wait for the router to flash the firmware and reboot automatically.
- By default, `lan4` is part of `br-lan` and uses the label MAC address.
- To query the RM520N-GL module, use the following command:
```bash
cat /dev/ttyUSB2 & printf 'ATI\r\n' > /dev/ttyUSB2
```
Signed-off-by: Yaoguang Bai <0xdeadc0de@badguys.club>
Link: https://github.com/openwrt/openwrt/pull/17093
Signed-off-by: John Crispin <john@phrozen.org>
Upstream uses devm_reset_control_array_get_optional_shared, which does
not use names. reset-names is also not specified in the documentation.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17118
Signed-off-by: John Crispin <john@phrozen.org>
Both generic-ehci.yaml and generic-ohci.yaml state that phy-names is to
only be usb.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17118
Signed-off-by: John Crispin <john@phrozen.org>
This matches the upstream PHY driver, which removed it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17118
Signed-off-by: John Crispin <john@phrozen.org>
Don't fail wireless interface bringup on empty PSK set. This is a valid
configuration, resulting in a PSK network which can't be connected to.
It does not fail the bringup of the hostapd process.
Keep failing the interface setup in case a password with invalid length
is used.
This is also beneficial when intending to configure a PPSK network. It
allows to create a network where no PPSK is yet set.
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://github.com/openwrt/openwrt/pull/17197
Signed-off-by: John Crispin <john@phrozen.org>
refresh the following patch for ath12k
001-wifi-ath12k-add-11d-scan-offload-support-and-handle-country-code-for-WCN7850.patch
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17246
Signed-off-by: John Crispin <john@phrozen.org>
One is already present. The other one can be implemented in terms of the
PHY.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17250
Signed-off-by: John Crispin <john@phrozen.org>
Ensure that the code doesn't pass macaddr_base with the wrong type (null)
to the supplicant setup/start call.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Name the pidfile of each dropbear instance according to the
corresponding uci section name. This enables a 1:1 mapping between the
definition of the service instance and its process.
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/15177
Signed-off-by: John Crispin <john@phrozen.org>
Instead of using regulator-output to manually control USB GPIO, let the
PHY handle it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17221
Signed-off-by: John Crispin <john@phrozen.org>
fix default timezone to correct GMT0,
origin value 'UTC' is zonename, not timezone.
Signed-off-by: Jiale Liu <admin@licsber.site>
Link: https://github.com/openwrt/openwrt/pull/15128
Signed-off-by: John Crispin <john@phrozen.org>
Initial support for dynamic reload of RxKHs.
In order to check if RxKHs need reloading.
RxKHs defined in the rxkh_file first has to be parsed and formated,
the same way as hostapd will read from the file and also output,
with the command GET_RXKHS.
Then each list of RxKHs can be hashed and compared.
Ucode implementation of hostapds rkh_derive_key() function.
Hostapd converts hex keys with 128-bits or more when less than 256-bits
to 256-bits, and truncates those that are more than 256-bits.
See: https://w1.fi/cgit/hostap/commit/hostapd/config_file.c?id=245fc96e5f4b1c566b7eaa19180c774307ebed79
Signed-off-by: Sybil127 <sybil127@outlook.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With rxkh_file, hostapd will read a list of RxKHs from a text file.
This also makes it possible for hostapd to dynamically reload RxKHs.
RxKHs defined in rxkh_file should be formated as described in hostapd.conf,
with one entry per line.
R0KH/R1KH format:
r0kh=<MAC address> <NAS Identifier> <256-bit key as hex string>
r1kh=<MAC address> <R1KH-ID> <256-bit key as hex string>
Reworked behavior of the uci options r0kh and r1kh.
When rxkh_file is not configured:
Instead of appending the RxKHs to the hostapd bss configuration.
They will be added to a interface specific file with name
/var/run/hostapd-phyX-apX.rxkh.
This file will be used as the rxkh_file in the hostapd bss configuration.
When rxkh_file is configured:
The specified file will be used in the hostapd bss configuration,
and will be the only source for configured RxKHs.
All RxKHs defined with the uci options r0kh or r1kh will be ignored.
Signed-off-by: Sybil127 <sybil127@outlook.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The initialization of mesh interfaces currently fail when wpa_supplicant
is not installed. This is due to the script calling the wpa_supplicant
feature indicator without verifying wpa_supplicant is installed at all.
To avoid failing, first check if wpa_supplicant is installed before
determining the available featureset.
Signed-off-by: David Bauer <mail@david-bauer.net>
