Commit Graph

72 Commits

Author SHA1 Message Date
INAGAKI Hiroshi
c441f9b2c5 mvebu: add support for IIJ SA-W2
Internet Initiative Japan Inc. (IIJ) SA-W2 is a network appliance with
11ac (Wi-Fi 5) wlan, based on 88F6810.

Specification:

- SoC         : Marvell Armada 380 88F6810
- RAM         : DDR3 256 MiB (Micron MT41K64M16TW-107:J x2)
- Flash       : SPI-NOR 32 MiB (Winbond W25Q256JVFIQ)
- WLAN        : 2.4/5 GHz, Mini PCI-E
  - 2.4 GHz   : Silex SX-PCEGN (Atheros AR9287 (2T2R))
  - 5 GHz     : Silex SX-PCEAC (Qualcomm Atheros QCA9880 (3T3R))
- Ethernet    : 10/100/1000 Mbps x5
  - Switch    : Marvell 88E6172
- LEDs/Keys   : 12x/1x
- UART        : "CONSOLE" port (RJ-45, RS-232C)
  - settings  : 115200n8
  - assignment: 1:NC,  2:NC,  3:TXD, 4:GND,
                5:GND, 6:RXD, 7:NC,  8:NC
  - note      : compatible with Cisco console cable
- Power       : DC Input or PoE
  - DC Input  : 12 VDC, 3 A
  - PoE       : 802.3af
    - module  : Silvertel Ag9712-2BR
    - note    : USB ports shouldn't be used when powered by PoE
- Bootloader  : PMON2000 based
- Stock       : NetBSD based

Flash instruction using sysupgrade image:

1. Prepare TFTP server with IP address 192.168.0.10 and put sysupgrade
   image to TFTP directory
2. Connect PC to "GE0/PoE" port on SA-W2
3. Power on SA-W2, interrupt count-down by Esc and enter to bootloader
   CLI
4. Set IP address of the device

   address 192.168.0.1

5. Download sysupgrade image and flash to storage

   tftpload 192.168.0.10 <image name>
   firmwrite

   example:

   #tftpload 192.168.0.10 openwrt-mvebu-cortexa9-iij_sa-w2-squashfs-sysupgrade.bin
   Loading openwrt-mvebu-cortexa9-iij_sa-w2-squashfs-sysupgrade.bin
   loaded 8127268 byte(s)
   #firmwrite
   Erasing FLASH block  32 Done 0x00200000.
   Erasing FLASH block  33 Done 0x00210000.
   ...
   Erasing FLASH block 155 Done 0x009b0000.
   Erasing FLASH block 156 Done 0x009c0000.
   Programming FLASH. Done.
   Verifying FLASH. No Errors found.

6. Check the flashed firmware

   firmcheck

   example:

   #firmcheck
   [Normal firmware]
   ident: 'SEIL2015'
   copyright: 'ARM OpenWrt Linux-5.15.93'
   version format: 1
   version major: 9
   version minor: 99
   version release: 'r22060+36-5163bb5e54'
   body size: 3578524
   checksum: 0x8a083cb8

   [Rescue firmware]
   ident: 'SEIL2015'
   copyright: 'Copyright (c) 2017 Internet Initiative Japan Inc. All rights reserved.'
   version format: 1
   version major: 3
   version minor: 70
   version release: 'Release'
   body size: 10152458
   checksum: 0x8f9518c2

7. Boot with the flashed firmware

   boot

Note:

- The bootloader on this device is not U-Boot and it's environment space
  ("bootloader-env") has no compatibility with U-Boot tools.

- eth1 is connected to port6 of 88E6172 switch, but multi-cpu port can't
  be handled on Linux Kernel and not defined.

- Powering by PoE hasn't been tested yet.

- This device has 2x OS images on flash and they can be switched by
  setting "BOOTDEV" variable on bootloader CLI.
  That variable supports the following values:

  - "flash" : primary image on flash ("firmware")
  - "rescue": secondary image on flash ("rescue")
  - "usb"   : usb storage (broken?)
  - "lan0/1": network

  command to set:

  set BOOTDEV=<dev>

  example:

    set BOOTDEV=rescue

  This commit also supports booting from secondary partition.

- To execute initramfs image on bootloader CLI, use "go" command.
  ("go" command is not listed on the output of "help", but available)

  example (download and execute):

    address 192.168.0.1
    tftpload 192.168.0.10 openwrt-mvebu-cortexa9-iij_sa-w2-initramfs-kernel.bin
    go

MAC addresses:

LAN    : 00:E0:4D:xx:xx:19 (none)
WAN    : 00:E0:4D:xx:xx:18 (board_info, 0x6 (hex))
2.4 GHz: 84:25:3F:xx:xx:xx (Mini PCI-E card)
5 GHz  : 84:25:3F:xx:xx:xx (Mini PCI-E card)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-10-31 14:02:01 +01:00
INAGAKI Hiroshi
b7c12a9bfc mvebu: add support for Fortinet FortiGate 30E
Fortinet FortiGate 30E (FG-30E) is a UTM, based on Armada 385 (88F6820).

Specification:

- SoC          : Marvell Armada 385 88F6820
- RAM          : DDR3 1 GiB (4x Micron MT41K256M8DA-125, "D9PSH")
- Flash        : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet     : 5x 10/100/1000 Mbps
  - Switch     : Marvell 88E6176
- LEDs/Keys    : 16x/1x
- UART         : "CONSOLE" port (RJ-45, RS-232C level)
  - port       : ttyS0
  - settings   : 9600bps 8n1
  - assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
                5:GND, 6:RXD, 7:NC , 8:NC
  - note       : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power        : 12 VDC, 2 A
  - plug       : Modex 5557-02R

Flash instruction using initramfs image:

 1. Power on FG-30E and interrupt to show bootmenu
 2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
    and set baudrate to 9600 bps
 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
    connect computer to "Image download port" in the parameters
 4. Prepare TFTP server with the parameters obtained above
 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
    directory
 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
    image from TFTP server
 7. Type "r" key when the following message is showed, to boot initramfs
    image without flashing to spi-nor flash

    "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"

 8. On initramfs image, backup mtd if needed

    minimum:

    - "firmware-info"
    - "kernel"
    - "rootfs"

 9. On initramfs image, upload sysupgrade image to the device and perform
    sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
    If the device is booted with stock firmware, login to bootmenu and
    call "[B]: Boot with backup firmware and set as default." to set the
    first OS image as default and boot it.

Notes:

- Both colors of Bi-color LEDs on the front panel cannot be turned on at
  the same time.

- "PWR" and "Logo" LEDs are connected to power source directly.

- The following partitions are added for OpenWrt.
  These partitions are contained in "uboot" partition (0x0-0x1fffff) on
  stock firmware.

  - "firmware-info"
  - "dtb"
  - "u-boot-env"
  - "board-info"

Image header for bootmenu tftp:

  0x0 - 0xf  : ?
 0x10 - 0x2f : Image Name
 0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?

*: required for initramfs image

MAC addresses:

(eth0): 70:4C:A5:xx:xx:CE (board-info, 0xd880 (hex))
WAN   : 70:4C:A5:xx:xx:CF
LAN 1 : 70:4C:A5:xx:xx:D0
LAN 2 : 70:4C:A5:xx:xx:D1
LAN 3 : 70:4C:A5:xx:xx:D2
LAN 4 : 70:4C:A5:xx:xx:D3

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-10-29 02:12:38 +02:00
Robert Marko
d6ac365e42
mvebu: eDPU: add support for version with external switch
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.

The same image can be used on both versions as U-Boot will enable the
switch node and disable the unused ethernet controller.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-09-19 12:12:17 +02:00
INAGAKI Hiroshi
5c65224d8f mvebu: add reset delays of PHYs for Fortinet FortiGate 50E
Add reset-(de)assert-us to ethernet PHYs on Fortinet FortiGate 50E to
solve instability after HW resetting of PHYs. (ex.: restarting "network"
service, etc...)

Fixes: #13391
Fixes: 102dc5a625 ("mvebu: add support for Fortinet FortiGate 50E")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-09-03 22:59:39 +02:00
INAGAKI Hiroshi
4fffa0f6af mvebu: use PHY LED trigger for speed LEDs on FortiGate 50E
Use <mdio>:<addr>:<speed> trigger instead of netdev(link) trigger for
Fortinet FortiGate 50E, to indicate link speed on the each phys.

1000 Mbps: Green
100 Mbps : Amber
10 Mbps  : (turn off)

Fixes: 102dc5a625 ("mvebu: add support for Fortinet FortiGate 50E")

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-05-18 16:17:52 +02:00
INAGAKI Hiroshi
102dc5a625 mvebu: add support for Fortinet FortiGate 50E
Fortinet FortiGate 50E (FG-50E) is a UTM, based on Armada 385 (88F6820).

Specification:

- SoC          : Marvell Armada 385 88F6820
- RAM          : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash        : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet     : 7x 10/100/1000 Mbps
  - LAN 1-5    : Marvell 88E6176
  - WAN 1, 2   : Marvell 88E1512 (2x)
- LEDs/Keys    : 18x/1x
- UART         : "CONSOLE" port (RJ-45, RS-232C level)
  - port       : ttyS0
  - settings   : 9600bps 8n1
  - assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
                 5:GND, 6:RXD, 7:NC , 8:NC
  - note       : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power        : 12 VDC, 2 A
  - plug       : Molex 5557-02R

Flash instruction using initramfs image:

1. Power on FG-50E and interrupt to show bootmenu
2. Call "[R]: Review TFTP parameters.", check TFTP parameters and
   connect computer to "Image download port" in the parameters
3. Prepare TFTP server with the parameters obtained above
4. Rename OpenWrt initramfs image to "image.out" and put to TFTP
   directory
5. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
   image from TFTP server
6. Type "r" key when the following message is showed, to boot initramfs
   image without flashing to spi-nor flash

   "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"

7. On initramfs image, backup mtd if needed

   minimum:

   - "firmware-info"
   - "kernel"
   - "rootfs"

7. On initramfs image, upload sysupgrade image to the device and perform
   sysupgrade
8. Wait ~200 seconds to complete flashing and rebooting.
   If the device is booted with stock firmware, login to bootmenu and
   call "[B]: Boot with backup firmware and set as default." to set the
   first OS image as default and boot it.

Notes:

- All "SPEED" LEDs(Green/Amber) of LAN and 1000M "SPEED" LEDs(Green) of
  WAN1/2 are connected to GPIO expander. There is no way to indicate
  link speed of networking device on Linux Kernel/OpenWrt, so those LEDs
  cannot be handled like stock firmware.
  On OpenWrt, use netdev(link) trigger instead.

- Both colors of Bi-color LEDs on the front panel cannot be turned on at
  the same time.

- "PWR" and "Logo" LEDs are connected to power source directly.

- The following partitions are added for OpenWrt.
  These partitions are contained in "uboot" partition (0x0-0x1fffff) on
  stock firmware.

  - "firmware-info"
  - "dtb"
  - "u-boot-env"
  - "board-info"

Image header for bootmenu tftp:

  0x0 - 0xf  : ?
 0x10 - 0x2f : Image Name
 0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?

*: required for initramfs image

MAC addresses:

(eth0): 70:4C:A5:xx:xx:7C (board-info, 0xd880 (hex))
WAN 1 : 70:4C:A5:xx:xx:7D
WAN 2 : 70:4C:A5:xx:xx:7E
LAN 1 : 70:4C:A5:xx:xx:7F
LAN 2 : 70:4C:A5:xx:xx:80
LAN 3 : 70:4C:A5:xx:xx:81
LAN 4 : 70:4C:A5:xx:xx:82
LAN 5 : 70:4C:A5:xx:xx:83

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-03-08 23:49:39 +01:00
Arınç ÜNAL
9df035b3ea treewide: remove label = "cpu" from DSA dt-binding
This is not used by the DSA dt-binding, so remove it from all devicetrees.

Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=9cc115d8d6f73dd260de1609182f3645844d6907
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2023-02-26 22:22:48 +01:00
Daniel González Cabanelas
be0f1c1b26 mvebu: add support for Buffalo LinkStation LS220DE
The Buffalo LinkStation LS220DE is a dual bay NAS, based on Marvell
Armada 370

Hardware:
   SoC:         Marvell Armada 88F6707
   CPU:         Cortex-A9 800 MHz, 1 core
   Flash 1:     SPI-NOR 1 MiB (U-Boot)
   Flash 2:     NAND 512 MiB (OS)
   RAM:         DDR3 256 MiB
   Ethernet:    1x 1GbE
   USB:         1x 2.0
   SATA:        2x 3Gb/s
   LEDs/Input:  5x / 2x (1x button, 1x slide-switch)
   Fan:         1x casing

Flash instructions, from hard drive:
  1. Get access to the "boot" partition at the hard drive where the stock
     firmware is installed. It can be done with acp-commander or by
     plugging the hard drive to a computer.
  2. Backup the stock uImage:
         mv /boot/uImage.buffalo /boot/uImage.buffalo.bak
  3. Move and rename the Openwrt initramfs image to the boot partition:
         mv openwrt-initramfs-kernel.bin /boot/uImage.buffalo
  4. Power on the Linkstation with the hardrive inside. Now Openwrt will
     boot, but still not installed.
  5. Connect via ssh to OpenWrt:
         ssh root@192.168.1.1
  6. Rename boot files inside boot partition
         mount -t ext3 /dev/sda1 /mnt
         mv /mnt/uImage.buffalo /mnt/uImage.buffalo.openwrt.bak
         mv /mnt/initrd.buffalo /mnt/initrd.buffalo.bak
  7. Format ubi partitions at the NAND flash ("kernel_ubi" and "ubi"):
         ubiformat /dev/mtd0 -y
         ubidetach -p /dev/mtd1
         ubiformat /dev/mtd1 -y
  8. Flash the sysupgrade image:
         sysupgrade -n openwrt-squashfs-sysupgrade.bin
  9. Wait until it finish, the device will reboot with OpenWrt installed
     on the NAND flash.

Restore the stock firmware:
  1. Take the hard drive used for the installation and restore boot backup
     files to their original names:
         mount -t ext3 /dev/sda1 /mnt
         mv /mnt/uImage.buffalo.bak /mnt/uImage.buffalo
         mv /mnt/initrd.buffalo.bak /mnt/initrd.buffalo
  2. Boot from the hard drive and perform a stock firmware update using
     the Buffalo utility. The NAND will be restored to the original
     state.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-02-26 22:22:48 +01:00
Daniel Golle
aa41f4a395 mvebu: setup effective thermal zones on Puzzle M901 and M902
Assign fan with 4 active cooling levels to be used for the main CPU as
well as external SerDes units.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-02-25 19:01:40 +00:00
Robert Marko
00c5276659
mvebu: mochabin: enlarge PCI memory window
Armada 7040 uses a rather small 15MB memory window for every PCI adapter,
however this is not sufficient for Qualcomm QCA6390 802.11ax cards that
are shipped along with the OpenWrt WLAN model of MOCHAbin as ath11k
requires at least 16MB of memory.

So, similar to what MACCHIATOBin has been doing for years, lets move
to using the second PCIe 2 memory window and expand it to 128MB to
make it future proof.

This has been already sent upstream [1].
[1] https://lore.kernel.org/linux-arm-kernel/20230219121418.1395401-1-robert.marko@sartura.hr/

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-02-21 17:15:40 +01:00
Enrico Mioso
d3e89e69c5 mvebu: harmonize GL.iNet GL-MV1000 MTD partitions layout with vendor
The GL-MV1000 ships with a 16MB spi-nor flash, containing a copy of the stock GL.iNet firmware.
Add the corresponding flash areas, so our view matches the one of the in-flash stock firmware.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
2023-01-06 19:59:42 +01:00
Robert Marko
57a38c8d3e mvebu: add Methode euroDPU support
Add support for Methode euroDPU which is based on uDPU but does not
have a second SFP cage, instead of which a Maxlinear G.hn IC is used.

PHY mode is set to 1000Base-X despite Maxlinear IC being capable of
2500Base-X since until 5.15 support for mvebu is available trying to use
2500Base-X will cause buffer overruns for which the fix is not easily
backportable.

Installation instructions:
1. Boot the FIT initramfs image (openwrt-mvebu-cortexa53-methode_edpu-initramfs.itb)
2. sysupgrade using the openwrt-mvebu-cortexa53-methode_edpu-firmware.tgz

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-06-29 13:08:59 +02:00
Robert Marko
7f73acade0 mvebu: update and refactor uDPU DTS
uDPU DTS has pending upstream fixups, so backport those as well as split
the DTS into a DTSI and DTS in preparation for euroDPU support which
uses uDPU as the base.

Ethernet aliases have not yet been sent upstream but will be soon in order
for U-boot to set the correct MAC on both ethernet interfaces instead of
just one.

Since U-boot environment now has its own partition, update the envtools
config script to search for it instead.

Patch hardcoding PHY mode is also not applicable anymore, so drop it and
set in the uDPU DTS directly.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-06-29 13:08:59 +02:00
Enrico Mioso
22436d762b mvebu: mark all mtd partitions on GL.iNet GL-MV1000 read-only
On this device, two of the three defined MTD partitions are
automatically set to read-only, since they do not end at an
erase/write block boundary.

In particular, the only partition remaining writable is the
one holding the u-boot bootloader.

Mark all of the partitions read-only, at least until a better
understanding of why the layout has been laid out this way is
gained.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
2022-02-19 18:29:42 +01:00
Sungbo Eo
6ff970bb51 mvebu: add support for ipTIME NAS1dual
ipTIME NAS1dual is a 1-bay NAS, based on Marvell Armada 385 SoC.

Specifications:
* SoC: 88F6820
* RAM: 2 GiB
* Flash: SPI NOR 64 MiB
* SATA: 1x 3Gb/s
* Ethernet: 2x 1GbE
* USB: 1x 3.0
* Fan: 2 speed level
* UART: J11 (115200 8N1)
  * Pinout: [3V3] (TXD) (RXD) (GND)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Pawel Dembicki
9149ed4f05 mvebu: cortexa9: Add support for Ctera C200-V2
2-Bay NAS - maximum two 3.5" Harddisks

Hardware:
  - SoC: Marvell 88F6707-A1 ARMv7 Processor 1,2GHz (ARMADA 370 SoC)
  - Ram: 1GB (2x Nanya NT5CC512M8DN-D1)
  - NAND Flash: 256MB (ESMT F59L2G81A-25T)
  - Lan: 1x GBE (Marvell 88E1318-NNB2)
  - Storage: 2x SATA HDD 3.5" Slot
  - USB: 2x USB 3.0 port (Renesas uPD720202)
  - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND)
  - LEDs: 13x GPIO controlled
  - Buttons: 2x GPIO controlled

Known issues:
  - Buzzer is unused due lack of proper driver
  - USB1/2 usbport ledtrigger won't work (through DT)
  - Renesas uPD720202 requires firmware file. It's possible to find
    non-free binary. Please look for 'UPDATE.mem' file and put in into
    '/lib/firmware/renesas_usb_fw.mem' file.

Installation:
  - Apply factory initramfs image via stock web-gui.
  - Do sysupgrade to make installation complete.

Back to stock:
  - OpenWrt rootfs partition use unused space after stock firmware.
  - Full revert is possible.
  - Login via ssh and run:

 ## ctera_c200-v2_back_to_factory start ##
 . /lib/functions.sh
 part=$(find_mtd_part "active_bank")
 active_bank=$(strings "$part" | grep bank)
 if [ "$active_bank" = "bank1" ]; then
 	echo "bank2" > /tmp/change_bank
 else
 	echo "bank1" > /tmp/change_bank
 fi
 mtd write /tmp/change_bank active_bank
 reboot
 ## ctera_c200-v2_back_to_factory end ##

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(put back-to-stock script into commit message, removed dup. SUBPAGESIZE var,
added 01_leds for non-working dt-usb-port trigger)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:41:19 +01:00
Daniel Golle
f81a06408e
mvebu: enable Aquantia phy driver for Puzzle devices
Fixes Ethernet link status on all ports and makes 2.5G ports usable
in 2.5G and 1G full-duplex mode.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-23 20:17:42 +00:00
Daniel Golle
962c585580
mvebu: remove accidentally added file
Remove accidentally added file (which was a left-over of a by-now
replaced driver)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 23:44:45 +00:00
Daniel Golle
3684b494dd
mvebu: puzzle-m901: add LEDs, fan and reset button
Wire up MCU driver for LEDs, fan and temperature sensor, and add
GPIO reset button just like on the M902 also on the Puzzle M901.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 21:54:54 +00:00
Daniel Golle
ddad936fc6
mvebu: puzzle-m902: add GPIO reset button
Add reset button to device tree so it has the function expected from
usual OpenWrt devices.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 21:54:49 +00:00
Daniel Golle
f0c0b18234
mvebu: puzzle-m902: add driver for MCU driving LEDs, fan and buzzer
Backport MFD driver for communicating with the on-board MCU found on
IEI World Puzzle appliances.
Improve the driver to support multiple LEDs, apply a default state and
let MCU take care of blinking if timing is within supported range.
Wire up LEDs and fan for Puzzle M902 in device tree.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-21 16:41:10 +00:00
Robert Marko
46646efc38 mvebu: mochabin: correct LED labels in DTS
LED labels got reversed by accident, so fix it to the usual color:led_name format.

Fixes: 78cf3e53b1 ("mvebu: add Globalscale MOCHAbin")

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-09 19:27:11 +02:00
Robert Marko
78cf3e53b1 mvebu: add Globalscale MOCHAbin
Globalscale MOCHAbin is a Armada 7040 based development board.

Specifications:
* Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
* 2 / 4 / 8 GB of DDR4 DRAM
* 16 GB eMMC
* 4MB SPI-NOR (Bootloader)
* 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
* 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
* 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
* 1x SATA 7+15 socket (SATA3)
* 1x 16-pin (2×8) MikroBus Connector
* 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
* 2x USB3.0 Type-A ports via SMSC USB5434B hub
* Cortex 2x5 JTAG
* microUSB port for UART (PL2303GL/PL2303SA onboard)
* 1x 10G SFP+
* 1x 1G SFP (Connected to 88E1512 PHY)
* 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
* 4x 1G RJ45 ports via Topaz 88E6141 switch
* RTC with battery holder (SoC provided, requires CR2032 battery)
* 1x 12V DC IN
* 1x Power switch
* 1x 12V fan header (3-pin, power only)
* 1x mini-PCIe LED header (2x0.1" pins)
* 1x M.2-2280 LED header (2x0.1" pins)
* 6x Bootstrap jumpers
* 1x Power LED (Green)
* 3x Tri-color RGB LEDs (Controllable)
* 1x Microchip ATECC608B secure element

Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
parallel connected to the same PHY.

Installation:

Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a72_musl/linux-mvebu_cortexa72/image-armada-7040-mochabin.dtb bin/targets/mvebu/cortexa72/
$ in.tftpd -L -s bin/targets/mvebu/cortexa72/

Connect to the device UART via microUSB port and power on the device.

Power on the device and hit any key to stop the autoboot.

Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device

Set the ethernet device (Example for the 1G WAN):
$ setenv ethact mvpp2-2

Ping server to confirm network is working:
$ ping $serverip
Using mvpp2-2 device
host 192.168.1.15 is alive

Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa72-globalscale_mochabin-initramfs-kernel.bin
$ tftpboot $fdt_addr_r image-armada-7040-mochabin.dtb

Boot the image:
$ booti $kernel_addr_r - $fdt_addr_r

Once the initramfs is booted, transfer openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
to /tmp dir on the device.

Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img of=/dev/mmcblk0 && sync

Reboot the device.

Hit any key to stop the autoboot.

Reset U-boot env and set the bootcmd:
$ env default -a
$ setenv bootcmd 'load mmc 0 ${loadaddr} boot.scr && source ${loadaddr}'

Optionally I would advise to edit the console env variable to remove earlycon as that
causes the kernel to never use the driver for the serial console.
Earlycon should be used only for debugging before the kernel can configure the console
and will otherwise cause various issues with the console.

$ setenv console 'console=ttyS0,115200'

Save and reset
$ saveenv
$ reset

OpenWrt should boot from eMMC now.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-10-02 16:45:35 +02:00
Ian Chang
70c75965a9 mvebu: add support for iEi Puzzle-M901/Puzzle-M902
Hardware specification
 ----------------------
 * CN9130 SoC, Quad-core ARMv8 Cortex-72 @ 2200 MHz
 * 4 GB DDR
 * 4 GB eMMC
 * mmcblk0
 - mmcblk0p1    64M  kernel_1
 - mmcblk0p2    64M  kernel_2
 - mmcblk0p3   512M  rootfs_1
 - mmcblk0p4   512M  rootfs_2
 - mmcblk0p5   512M  Reserved
 - mmcblk0p6    64M  Reserved
 - mmcblk0p7   1.8G  rootfs_data

 * 4 MB (SPI Flash)
 * 6 x 2.5 Gigabit  ports (Puzzle-M901)
 - External PHY with 6 ports (AQR112R)

 * 6 x 2.5 Gigabit ports (Puzzle-M902)
 - External PHY with 6 ports (AQR112R)
   3 x 10 Gigabit ports (Puzzle-M902)
 - External PHY with 3 ports (AQR113R)

 * 4 x Front panel LED
 * 1 x USB 3.0
 * Reset button on Rear panel
 * UART (115200 8N1,header on PCB)

 Flash instructions:
    The original firmware is based on OpenWrt.
    Flash firmware using LuCI and CLI

Signed-off-by: Ian Chang <ianchang@ieiworld.com>
2021-09-09 23:36:13 +02:00
Ansuel Smith
2ca8e424b9 mvebu: convert mtd-mac-address to nvmem implementation
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-07-19 14:51:22 +02:00
Daniel González Cabanelas
26a5aea9bc mvebu: LS421DE: improve pin configuration
The CLK125 output pin at the ethernet PHY is connected via capacitor to
GND and nowhere else. Disable it. Also tune the LED masks.

The MPP56 and MPP60 pins at the SoC are conected to the μPD720202 USB3.0
chip:
  - MPP56: wired to PCIe CLKREQ# (out)
  - MPP60: wired to PCIe RESET# (in)
Configure the pcie pinmux for these pins.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2021-05-01 00:37:15 +02:00
Sven Eckelmann
c20ac84803 mvebu: Fix mac addresses for GL.iNet GL-MV1000
The original GL.iNet firmware has two different mac addresses in the
factory/art partition. The first one is for the WAN interface only and the
second one is for both lan0 and lan1.

But the original submission for OpenWrt didn't initialize the mac
addresses of the LAN ports for the DSA device at all. The ethernet mac
address was then used for all DSA ports.

Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-03-27 16:56:50 +01:00
Sven Eckelmann
01b911a938 mvebu: Add button support for GL.iNet GL-MV1000
The original patch to support this device advertised support for the reset
button and the "switch" in the commit message. But neither were actually
integrated in the device tree or documented anywere.

The button itself is now used to trigger a reset (as described in the
official GL.iNet documentation). The switch itself is registered as BTN_0
like other devices from GL.iNet in ath79.

Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-03-27 16:22:11 +01:00
Tad Davanzo
15309f5133 mvebu: venom resize kernel to 6MB
venom has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.

venom uboot however as set from factory will load up to 6MB.
This can be observed by looking a uboot log:
	NAND read: device 0 offset 0x900000, size 0x600000
	6291456 bytes read: OK
and from uboot environment variables:
	$ fw_printenv | grep "priKernSize";
	priKernSize=0x0600000

Resize the root partitions from 120MB to 117MB to let kernel expand
into it another 3MB.
And set kernel target size to 6MB.

Lastly set the kernel-size-migration compatibility version on venom to
prevent sysupgrading without first reinstalling from a factory image.

Signed-off-by: Tad Davanzo <tad@spotco.us>
2021-03-19 15:30:01 +01:00
Daniel González Cabanelas
b0235c0d8d mvebu: LS421DE: make cosmetics changes in dts file
Make some cosmetic changes in the Buffalo LinkStation LS421DE NAS:
  - Delete pointless #xxx-cells
  - bootargs: replace earlyprintk with earlycon and remove unneeded args.
  - Separate pinmux nodes with empty lines.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2021-03-13 20:15:29 +00:00
Jeff Collins
6e0c780eb3 mvebu: add LED support for GL.iNet GL-MV1000
This patch enables LED support for the GL.iNet GL-MV1000

Signed-off-by: Jeff Collins <jeffcollins9292@gmail.com>
[add SPDX identifier on new file, add aliases, minor cosmetic issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-26 13:57:50 +01:00
Adrian Schmutzler
7be8ab4f7b mvebu: remove upstreamed DTS files in 5.10
Some armada-3720-espressobin-* files have been upstreamed, move
these to files-5.4.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-23 18:31:35 +01:00
Daniel González Cabanelas
24b910dca2 mvebu: LS421DE: fix the thermal zones
The thermal zones kernel documentation is misleading, we cannot use more
than one sensor in a thermal zone node.

Furthermore the drivetemp driver for some reason it only catches one
sensor from the hard drives array (the first available).

In the Buffalo Linkstation LS421DE board there is also a sensor at the
ethernet phy chip that can also be monitored. Very useful to stop the fan
when there are no hard drives in the bays.

(It might be also possible to add the CPU sensor, but it requires kernel
patching for registering the sensor via device tree, using the function:
devm_thermal_zone_of_sensor_register)

Fix the thermal zones to use only one sensor per node and add the ethernet
phy sensor. Also adjust the hdd temperatures to be more conservative for
a mechanical hard drive.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2021-01-30 01:03:00 +01:00
Daniel González Cabanelas
b8362c20e7 mvebu: LS421DE: use the RTC as a wakeup source
The Buffalo Linkstation LS421DE comes with a Ricoh RS5C372A real time
clock. This RTC has the INTRA pin connected to the power management
circuit, allowing to wake up the device from the power off state when an
alarm is scheduled.

Add the "wakeup-source" property in the RTC dts node to allow the use
of the alarm.

Example of use, the device is powered off and it comes to life after 5
minutes:
echo $(expr $(date '+%s') + 60 * 5) > /sys/class/rtc/rtc0/wakealarm
poweroff

This feature isn't available in the stock firmware.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-12-22 18:59:10 +01:00
Daniel González Cabanelas
3064651bf7 mvebu: LS421DE: fix low performance issue
The Buffalo Linkstation LS421DE isn't able to enable the Level 2 cache
(AKA Aurora cache). As of result of this, the throughput is about half of
the expected, e.g when doing network data transfers.

Fix it by adding the broken-idle property in the coherency fabric node.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-12-22 18:59:10 +01:00
Vladimir Vid
c0af4a0ca2 mvebu: add initial support for Globalscale ESPRESSObin-Ultra
This patch adds support for Globalscale ESPRESSObin-Ultra. Device uses
the same Armada-3720 SoC with extended hardware support.

- SoC: Armada-3720
- RAM: 1 GB DDR4
- Flash: 4MB SPI NOR (mx25u3235f) + 8 GB eMMC
- Ethernet: Topaz 6341 88e6341 (4x GB LAN + 1x WAN with 30W PoE)
- WiFI: 2x2 802.11ac Wi-Fi marvell (88w8997 PCIe+USB)
- 1x USB 2.0 port
- 1x USB 3.0 port
- 1x microSD slot
- 1x mini-PCIe slot (USB [with nano-sim slot])
- 1x mini-USB debug UART
- 1x RTC Clock and battery
- 1x reset button
- 1x power button
- 4x LED (RGBY)
- Optional 1x M.2 2280 slot

** Installation **

Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a53_musl/linux-mvebu_cortexa53/
linux-5.4.65/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dtb
bin/targets/mvebu/cortexa53/
$ in.tftpd -L -s bin/targets/mvebu/cortexa53/

Connect to the device UART via microUSB port on the back side and power on the device.

Power on the device and hit any key to stop the autoboot.

Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device

Ping server to confirm network is working:
$ ping $serverip
Using neta@30000 device
host 192.168.1.15 is alive

Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-initramfs-kernel.bin
$ tftpboot $fdt_addr_r armada-3720-espressobin-ultra.dtb

Set the console and boot the image:
$ setenv bootargs $console
$ booti $kernel_addr_r - $fdt_addr_r

Once the initramfs is booted, transfer openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
to /tmp dir on the device.

Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img of=/dev/mmcblk0 && sync

Reboot the device.

Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
2020-11-23 22:53:15 +01:00
Adrian Schmutzler
2658008a2a treewide: remove default-state off for LEDs
default-state = "off" is default for LEDs, no need to specify it
explicitly.

https://www.kernel.org/doc/Documentation/devicetree/bindings/leds/common.yaml

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-16 13:43:39 +01:00
Daniel González Cabanelas
4e885dd90a mvebu: LS421DE: improve the HDD leds
Improve the HDD LEDs used for disk activity:
 - Use the trigger activity per ata channel

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-11-16 13:43:39 +01:00
Adrian Schmutzler
0cfdc7d446 target: update SPDX license names
SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to
GPL-2.0-or-later. Reflect that in the SPDX license headers.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-22 20:58:26 +02:00
Daniel González Cabanelas
42d14ace3e mvebu: LS421DE: add linkstation poweroff driver
Compile the Linkstation poweroff module for the Buffalo LS421DE.
Without this driver the device remains forever halted if a power off
command is executed.

The driver will also allow to use the WoL feature, which wasn't availabe
in the stock firmware.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-08-28 10:44:29 +01:00
Daniel González Cabanelas
a902e6a657 mvebu: LS421DE: use automatic fan control with thermal zones
The Buffalo Linkstation LS421DE has a chassis fan for cooling two internal
hard drives. Currently there is no control over this fan, running always
at fixed medium speed.

With the recent jump to the kernel 5.4, now we can monitor the hard drive
temperature and control the fan with thermal zones.

Install the kmod-hwmon-drivetemp module and wire up a thermal zone on the
dts file to allow automatic fan control by the kernel.

Tested succesfully using a single Crucial BX500 SSD drive.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-07-04 21:12:42 +02:00
Daniel González Cabanelas
0cca96284a mvebu: LS421DE: dts file improvements
- Delete useless HDD presence inputs: they aren't buttons, and probably
  they are outputs in the stock firmware.
- Change the Function Button keycode: the current one isn't mapped by
  the kernel module.
- Use the recommended property names for the ethernet stuff.
- Add missing i2c pinmux.
- Minor cosmetic changes.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-06-27 00:19:13 +02:00
Adrian Schmutzler
3c20bb0644 mvebu: consolidate DTS files
The DTS files in files-4.19 and files-5.4 are exactly identical
except for one file (armada-3720-uDPU.dts), which is only present
for 4.19, as it has been upstreamed before 5.4.

Since there is no point in maintaining all these identical files
twice, this patch moves them to the "files" directory, only keeping
the named exception to files-4.19.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-23 21:02:40 +02:00
Hauke Mehrtens
47106f55e0 mvebu: move files to files-4.9 and files-4.4 folder
This is needed to prevent copying it into kernel 4.14.
These device tree files are already integrated into kernel 4.14 and we
would like to use the upstream versions only.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-13 22:24:56 +01:00
Henryk Heisig
6674aa9798 mvebu: wrt3200acm enable SDIO interface
add mwifiex-sdio package to wrt3200acm

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-03-11 14:16:28 +01:00
Ansuel Smith
2261c9cc77 mvebu: add default sata trigger
Change dts file to add default sata trigger to sata led.

Backport upstream accepted patch to add sata trigger to device tree
source files already upstreamed.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[backport upstream accepted patch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-08 19:06:04 +01:00
Álvaro Fernández Rojas
89ecfa7556 mvebu: several fixes for Linksys WRT3200ACM
- Fix WLAN LEDs definition.
- Fix USB pinctrl definition.
- Remove SDHCI definition.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2017-01-13 17:12:40 +01:00
Kabuli Chana
fe876e9ac6 mvebu: Fix up some leds on this series
correct ports, fix power led on rango, tested mamba,shelby,rango

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
2017-01-10 12:28:32 +01:00
Mathias Kresin
5640986001 mvebu: revert remove of mvsw61xx device tree nodes
The marvell,88e6352 and marvell,88e6172 compatible strings are used in
target/linux/generic/files/drivers/net/phy/mvsw61xx.c. No idea why grep
missed them when I searched for them.

Thanks to Syrone Wong for noticing and reporting my mistake.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-13 09:03:52 +01:00
Mathias Kresin
de40d45363 treewide: dts: fix dtc compiler warnings
Fixes invalid device tree parameters.

Drop the mvsw61xx node used in mvebu device tree source files. It looks
like some kind of ethernet switch cargo cult. Neither the
marvell,88e6352 nor the marvell,88e6172 compatible strings can be found
in any LEDE file or in the kernel sources.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-12 21:04:15 +01:00