TP-Link and ASUS OnHub devices are very similar, sharing many of the
same characteristics and much of their Device Tree. They both run a
version of ChromeOS for their factory firmware, and so installation
instructions look very similar to Google Wifi [1].
Things I've tested, and are working:
* Ethernet
* WiFi (2.4 and 5 GHz)
* LEDs
* USB
* eMMC
* Serial console (if you wire it up yourself)
* 2x CPU
* Speaker
== Installation instructions summary ==
1. Flash *-factory.bin to a USB drive (e.g., with `dd`)
2. Insert USB drive, to boot OpenWrt from USB
3. Copy the same *-factory.bin over to device, and flash it to eMMC to
make OpenWrt permanent
== Developer mode, booting from USB (Step 2) ==
To enter Developer Mode and boot OpenWrt from a USB stick:
1. Unplug power
2. Gain access to the "developer switch" through the bottom of the
device
3. Hold down the "reset switch" (near the USB port / power plug)
4. Plug power back in
5. The LED on the device should turn white, then blink orange, then
red. Release the reset switch.
6. Insert USB drive with OpenWrt factory.bin
7. Press the hidden developer switch under the device to boot to USB;
you should see some activity lights (if you have any) on your USB
drive
8. Depending on your configuration, the router's LED(s) should come on.
You're now running OpenWrt off a USB stick.
These instructions are derived from:
https://www.exploitee.rs/index.php/Rooting_The_Google_OnHub#Enabling_%22Developer_Mode%22_on_the_OnHubhttps://www.exploitee.rs/index.php/Asus_OnHub#Enabling_%22Developer_Mode%22_on_the_OnHub
~~Finding the developer switch:~~ for TP-Link, the developer switch is
on the bottom of the device, underneath some of the rubber padding and a
screw. For ASUS, remove the entire base, via 4 screws under the rubber
feet. See the Exploitee instructions for more info and photos.
== Making OpenWrt permanent (on eMMC) (Step 3) ==
Once you're running OpenWrt via USB:
1. Connect Ethernet to the LAN port; router's LAN address should be at
192.168.1.1
2. Connect another system to the router's LAN, and copy the factory.bin
image over, via SCP and SSH:
scp -O openwrt-ipq806x-chromium-tplink_onhub-squashfs-factory.bin root@192.168.1.1:
ssh root@192.168.1.1 -C "dd if=/dev/zero bs=512 seek=7552991 of=/dev/mmcblk0 count=33 && \
dd if=/root/openwrt-ipq806x-chromium-tplink_onhub-squashfs-factory.bin of=/dev/mmcblk0"
3. Reboot and remove the USB drive.
== Developer mode beep ==
Note that every time you boot the OnHub in developer mode, the device
will play a loud "beep" after a few seconds. This is described in the
Chromium docs [2], and is intended to make it clear that the device is
not running Google software. It is nontrivial to completely disable this
beep, although it's possible to "acknowledge" developer mode (and skip
the beep) by using a USB keyboard to press CTRL+D every time you boot.
[1] https://openwrt.org/toh/google/wifi
[2] https://chromium.googlesource.com/chromiumos/docs/+/HEAD/developer_mode.md
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For IPQ8064 systems based off the "Google Storm" reference platform,
such as the TP-Link OnHub.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This fixes device tree registration for 'qcom,lpass-cpu' as used by
qcom-ipq8064 SoCs, and allows speaker audio to function.
This patch has been submitted (and merged, for -next; likely v6.3)
upstream.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Refresh target config with `make kernel_menuconfig`, then save the
result. This drops missing symbols or otherwise accounts for defaults.
It should not change any functionality.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Similar to commit 4d8b42d8a7 ("ipq40xx: point to externally compiled
dtbs in recipes").
Currently, we patch our DTS files into the kernel source tree, so the
kernel build process will produce DTBs for us. The kernel-to-DTS
dependency can cause buildroot to perform excessive rebuilds of the
kernel though, which slows down device development iteration.
Buildroot also compiles DTBs on its own, to
$(KDIR)/image-$(DEVICE_DTS).dtb. With small adjustments, we can leverage
this, and stop patching DTS files into the kernel Makefile at the same
time.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Refresh upstreamed patch with kernel version tag and replace them with
the upstream version.
For krait-cc patch rework them with the upstream changes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Removed upstreamed:
pending-5.15/101-Use-stddefs.h-instead-of-compiler.h.patch[1]
ipq806x/patches-5.15/122-01-clk-qcom-clk-krait-fix-wrong-div2-functions.patch[2]
bcm27xx/patches-5.15/950-0198-drm-fourcc-Add-packed-10bit-YUV-4-2-0-format.patch[3]
Manually rebased:
ramips/patches-5.15/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch[4]
Added patch/backported:
ramips/patches-5.15/107-PCI-mt7621-Add-sentinel-to-quirks-table.patch[5]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=c160505c9b574b346031fdf2c649d19e7939ca11
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=a051e10bfc6906d29dae7a31f0773f2702edfe1b
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=ec1727f89ecd6f2252c0c75e200058819f7ce47a
4. Quilt gave this output when I applied the patch to rebase it:
% quilt push -f
Applying patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch
patching file arch/mips/ralink/Kconfig
patching file drivers/pci/controller/Kconfig
patching file drivers/pci/controller/Makefile
patching file drivers/staging/Kconfig
patching file drivers/staging/Makefile
patching file drivers/staging/mt7621-pci/Kconfig
patching file drivers/staging/mt7621-pci/Makefile
patching file drivers/staging/mt7621-pci/TODO
patching file drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt
patching file drivers/staging/mt7621-pci/pci-mt7621.c
Hunk #1 FAILED at 1.
Not deleting file drivers/staging/mt7621-pci/pci-mt7621.c as content differs from patch
1 out of 1 hunk FAILED -- saving rejects to file drivers/staging/mt7621-pci/pci-mt7621.c.rej
patching file drivers/pci/controller/pcie-mt7621.c
Applied patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch (forced; needs refresh)
Upon inspecting drivers/staging/mt7621-pci/pci-mt7621.c.rej, it seems that
the original patch wants to delete drivers/staging/mt7621-pci/pci-mt7621.c
but upstream's version was not an exact match. I opted to delete that
file.
5. Suggestion by hauke: 19098934f9
"This patch is in upstream kernel, but it was backported to the old
staging driver in kernel 5.15."
Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Signed-off-by: John Audia <therealgraysky@proton.me>
Compex WPQ864 contains a non standard partition table. Each partition
node should be named partition and should contain a valid reg.
Fix an extra "-" present after the reg for SBL2_1 partition.
Also add "0:" to each qcom default partition following smem naming.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The refreshed patch actually use the format of <start size start size>
instead of <start end start end>. This cause boot fail since the rootfs
can't be mounted with these wrong values.
Fix it to the correct format in each affected dts.
Fixes: #11498
Fixes: 6134ba4a34 ("ipq806x: 5.15: add boot-partitions binding to fix block warning")
Tested-by: Matt Buczko <mbuczko@hotmail.com> # Askey RT4230W
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
It was tested that cache scaling currently cause instability problem.
This is probably caused by a latent misconfiguration that cause the L2
cache to be sourced from the wrong source and runs at an unstable freq
compared to the original QSDK fw.
To improve stability while the problem is bisected, disable the devfreq
drivers with minimal perf penality.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Define the kernel crash log storage ramoops/pstore feature
for C2600/AD7200 and add kmod-ramoops to default.
Tested with C2600 only.
Signed-off-by: Edward Matijevic <motolav@gmail.com>
Manually rebased:
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
[Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.
Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.
The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.
Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.
The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch was wrongly dropped with the assumption that it was moved to
generic. This wasn't the case and caused the malfunction of the Asrock
G10 router.
Reintroduce it to fix Asrock G10 functionality.
Fixes: 8cc2caed58 ("ipq806x: 5:15: add testing kernel version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Zyxel NGB6817 is the only router that use mmc for rootfs. Upstream
kernel dtsi have mmc-ddr-1_8v enabled for sddc1. This is wrong as mmc on
ipq806x is supplied by a fixed 3.3v regulator and can't operate at 1.8v.
This cause the sddc1 to malfunction and cause kernel panic.
In old 5.15 version this was disabled but it was put in addition to many
other changes so it was dropped silently. Restore this patch to fix
working condition of such router.
Fixes: 88bf652 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Fixes: #11000
Tested-by: Hendrik Koerner <koerhen@web.de>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In refreshing DTS to the upstream version an unwanted change slipped in
the commit. The ASRock G10 dts got converted to DSA without any support.
Revert this to swconfig driver to restore normal functionality.
Fixes: 88bf652525 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
We currently ignore ret of the nandc partition parser if unprotected
spare data is true. This is the case for ipq806x nand.
Backport patch that fix this error and correctly handle error from
partition parser.
Fixes: ae6a63bc97 ("ipq806x: 5.15: replace nandc patch with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add 6.1 tag to upstream patch now that 6.1 got tagged. This permits to
track patch in a better way and directly drop them on kernel bump.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add multiple patch for krait-cc modernization and multiple fixup for the
driver. Also modify a patch to enable the qsb fixed clock and add pxo to
krait-cc node.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
nand_pins definition is now shipped in ipq8064 dtsi. Rework the
nand_pins definition for wg2600hp3 5.15 files.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The patch has changed implementation and now the binding has changed.
Replace the old binding with boot-partitions and reimplement the
definition with the new definition.
The new definition is:
<offset1 size1 offset2 size2 offset3 ...>
and now supports sparsed patch.
Also add missing binding in some dts and add the backup boot partition
to the boot-partitions list.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Remove useless spm patch as using the normal qcom,spm compatible is
enough to register it with no clks.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Use a new implementation by using a devfreq driver to scale the shared
cache of the krait cpu cores.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport devfreq new cpufreq based PASSIVE governor needed for devfreq
based fab and cache scaling.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reorganize dtsi patches with upstream version and drop dtsi in 5.15
files.
Also add an additional upstream patch for hwspinlock support.
Refresh all the dts with needed changes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This doesn't cause any panic anymore and no regression are observed with
ath10k. Remove this additional patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Remove qcom adm Documentation patch that is not needed for the target.
Probably a leftover when the adm bus was added, now merged upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In preparation for a cleanup of 5.15 patches copy the files dir to 5.10
and 5.15 kernel version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Removed following upstreamed patch:
* bcm53xx: 081-next-ARM_dts_BCM53015-add-mr26.patch
All other patches automagically rebased.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add missing scaling_available_frequencies sysfs entry for dedicated
cpufreq driver.
This sysfs entry is not standard and each cpufreq driver needs to
provide it and declare it in the cpufreq driver struct attr.
Fixes: 5dbbefcbcc ("ipq806x: introduce dedicated krait cpufreq")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The order of LAN ports shown in Luci is reversed compared to what is
written on the case of the device. Fix the order so that they match.
Fixes: #10275
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware specs:
SoC: Qualcomm IPQ8065 (dual core Cortex-A15)
RAM: 512 MB DDR3
Flash: 256 MB NAND, 32 MB NOR
WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz
Switch: QCA8337
Ethernet: 5x 10/100/1000 Mbit/s
USB: 1x USB 3.0 Type-A
Buttons: WPS, Reset
Power: 12 VDC, 2.5 A
Ethernet ports:
1x WAN: connected to eth2
4x LAN: connected via the switch to eth0 and eth1
(eth0 is disabled in OEM firmware)
MAC addresses (OEM and OpenWrt):
fw_env @ 0x00 d4🆎82:??:??:?a LAN (eth1)
fw_env @ 0x06 d4🆎82:??:??:?b WAN (eth2)
fw_env @ 0x0c d4🆎82:??:??:?c WLAN 2.4 GHz (ath1)
fw_env @ 0x12 d4🆎82:??:??:?d WLAN 5 GHz (ath0)
fw_env @ 0x18 d4🆎82:??:??:?e OEM usage unknown (eth0 in OpenWrt)
OID d4🆎82 is registered to:
ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US
More info:
https://openwrt.org/inbox/toh/arris/tr4400_v2
IMPORTANT:
This port requires moving the 'fw_env' partition prior to first boot to
consolidate 70% of the usable space in flash into a contiguous partition.
'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords.
Its contents must be copied to 'rootfs_1' prior to booting via initramfs.
Note that the stock 'fw_env' partition will be wiped during sysupgrade.
A writable 'stock_fw_env' partition pointing to the old, stock location
is included in the port to help rolling back this change if desired.
Installation:
- Requires serial access and a TFTP server.
- Fully boot stock, press ENTER, type in:
mtd erase /dev/mtd21
dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21
umount /config && ubidetach -m 23 && mtd erase /dev/mtd23
- Reboot and interrupt U-Boot by pressing a key, type in:
set mtdids 'nand0=nand0'
set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)'
set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm'
env save
- Setup TFTP server serving initramfs image as 'recovery.bin', type in:
set ipaddr 192.168.1.1
set serverip 192.168.1.2
tftpboot recovery.bin && bootm
- Use sysupgrade to install squashfs image.
This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
[add 5.15 changes for 0069-arm-boot-add-dts-files.patch]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Converts extraction entries from 11-ath10k-caldata into
nvmem-cells in the individual board's device-tree file.
Same as commit 2047058 ("ipq806x: utilize nvmem-cells
for pre-calibration data")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
There is a mr25h256 spi flash on this machine. From the mtd backup
of the stock firmware, this spi flash is empty.
[ 3.652745] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16,
fifo:64
[ 3.653925] spi-nor spi0.0: mr25h256 (32 Kbytes)
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Fix wrong CPU OPP for ipq8062. Revision of the SoC added an
extra 25mV for every pvs. Also fix the voltage min/max value
that were wrong.
Reviewed-by: Robert Marko robimarko@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The existing device tree has incorrect definitions for usb3_0 and usb3_1
and the blocks they depend upon: their addresses and interrupts are
swapped. However, their clocks and resets are not. The result is that
the USB blocks are non-functional if only one of them is enabled.
This fix backports the definitions from mainline Linux 5.15 to
OpenWrt's 5.10 dtsi additions. See the relevant mainline code here:
https://github.com/torvalds/linux/blob/v5.17/arch/arm/boot/dts/qcom-ipq8064.dtsi#L1062-L1148
This fix does not break existing ports. But some ports may have enabled
both USB blocks even thought their board only implements one, because
enabling a single USB block would not have worked before this fix.
This means that revisiting all ports of ipq806x devices that implement
a single USB port is advised. This work must be done by maintainers that
can determine which USB block corresponds to the implemented port on
their hardware.
Note that this fix swaps the names of the hardware ports. This is
unfortunate, but will happen anyway when switching to kernel 5.15. Thus,
it is best to do this ASAP, before users get to depend on port names.
It is strongly recommended that this fix is backported to 22.03 before
its release. This will minimize the number of users affected by the port
name swap.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
This commit add some enabled symbols to generic config.
LTO is only supported by clang compiler and therefore should
be disabled in the generic config instead of duplicating this
symbol in each target. CONFIG_LTO_NONE do this job.
The second group of symbols is enabled by the options available
in the generic config and is therefore added here:
* CONFIG_AF_UNIX_OOB is selected by CONFIG_NET && CONFIG_UNIX,
* CONFIG_BINARY_PRINTF is selected by CONFIG_BPF_SYSCALL,
* CONFIG_NET_SOCK_MSG is selected by CONFIG_BPF_SYSCALL && CONFIG_NET.
The other symbols are disabled and should be in the generic config.
This commit also removes these symbols from subtargets.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Fix dedicated cpufreq for kernel 5.15 as they changed module
order and now it can happen that cpufreq probe after cache driver.
Also add lock between cache scaling in set_target as it's now required
by opp functions.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Now that smem actually free the leaked parts, when
a rootfs partition is detected, the kernel panics as
it try to free the static space allocated for the "ubi"
name. Change the logic and fix the name at the allocate_partition
function to correctly free the space allocated by smem.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Refresh patch for 5.15
Rework tweak patch to sync with upstream ipq8064 dtsi and fix
regression introduced.
Rename nand_controller to nand in every dts.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Timo Schroeder reported:
"The TP-Link Archer VR2600v is stuck in a boot loop on written
snapshot image. It's able to boot using the snapshot uimage
though, but there ath10k firmware can't be found.
21.02.2 release version doesn't have either problem."
The VR2600v has a 512 byte header at the beginning of the
firmware that needs to be accounted for.
Fixes: f6a01d7f5c ("ipq806x: convert TP-Link Archer VR2600v to denx,uimage")
Reported-by: Timo Schroeder <der.timosch@gmail.com>
References: <https://github.com/openwrt/openwrt/issues/9467>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add kmod-ramoops to the default set of device packages in
R7800 and XR500, so that the ramoops kernel crash logs
are provided by default for these routers.
The capability was earlier defined by 97158fe1 and cf346dfa,
but the feature was not yet turned on by default.
The possible kernel crashes are stored into /sys/fs/pstore/*
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Enable support for allocating user space page table entries in high memory [1],
for the targets which support this feature. This saves precious low memory
(permanently mapped, the only type of memory directly accessible by the kernel).
[1] https://www.kernel.org/doc/html/latest/vm/highmem.html
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Fixes following warning message during image building process:
Finalizing root filesystem...
root-ipq806x/lib/upgrade/asrock.sh: line 1: /lib/functions.sh: No such file or directory
Enabling boot
root-ipq806x/lib/upgrade/asrock.sh: line 1: /lib/functions.sh: No such file or directory
Enabling bootcount
Fixes#9350
Fixes: 98b86296e6 ("ipq806x: add support for ASRock G10")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Increase the kernel size from 3 MB to 4 MB for EA8500 and EA7500v1.
* modify the common .dtsi
* modify the kernel size in the image recipes
Define compat-version 2.0 to force factory image usage for sysupgrade.
Add explanation message. Reenable both devices.
As for 4MiB (and not more): Hannu Nyman noted that:
"We have lots of ipq806x devices with 4 MB kernel, so will
need action at that point in future in any case.
(Assuming that the bootloader did not have a 4 MB limit that
has been tested...)"
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
(squashed, added 4MiB notice of support in ipq806x)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Define the kernel crash log storage ramoops/pstore feature
for R7800 and its sister XR500.
Reference to the ramoops admin guide in upstream Linux:
https://www.kernel.org/doc/html/v5.10/admin-guide/ramoops.html
Tested with R7800.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The kernel of both images will no longer fit into
the 3072KiB / 3MiB kernel partition:
|Image Name: ARM OpenWrt Linux-5.10.100
|Created: Sat Feb 19 00:11:55 2022
|Image Type: ARM Linux Kernel Image (uncompressed)
|Data Size: 3147140 Bytes = 3073.38 KiB = 3.00 MiB
Disable both targets for now, until a solution is available.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Enabled `CONFIG_ALL_KMODS` and ran `make kernel_menuconfig` against
ipq806x to update defconfig.
The removed symbols are in fact present in
target/linux/generic/config-5.10. CONFIG_MDIO_DEVRES
was likely added due to this:
<https://elixir.bootlin.com/linux/v5.10.100/source/drivers/net/phy/Kconfig#L16>
Signed-off-by: John Audia <graysky@archlinux.us>
This device still had the legacy flash partitioning.
This is a problem, because neither the nvmem-cells
for mac-address and calibration. Nor the denx,uimage
mtd-splitter compatible would be picked up.
The patch also changes the node-names of the flash
and partition nodes to hopefully meet all the
current FDT trends.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Increase the available flash memory size in Netgear R7800
by repurposing the unused "netgear" partition that is
located after the firmware partition.
Available flash space for kernel+rootfs+overlay increases
by 68 MB from 32 MB to 100 MB.
In a typical build, overlay space increases from 15 to 85,
increasing the package installation possibilities greatly.
Reverting to the OEM firmware is still possible, as the OEM
firmware contains logic to initialise the "netgear" partition
if its contents do not match expectations. In OEM firmware,
"netgear" contains 6 UBI sub-partitions that are defined in
/etc/netgear.cfg and initialisation is done by /etc/preinit
This is based on fb8a578aa7
Signed-off-by: Mike Lothian <mike@fireburn.co.uk>
The recent device-tree modification that added pre-cal
nvmem-cells pushed the device's kernel+dtb over the
allotted 3072k KERNEL_SIZE.
> WARNING: Image file tplink_vr2600v-uImage is too big: 3147214 > 3145728
There was a previous kernel partition size upgrade:
commit 0c967d92b3 ("ipq806x: increase kernel partition size for the TP-Link Archer VR2600v")
It has been seemingly upgraded from a 2048k KERNEL_SIZE in the past.
The commit talks about using the MTD_SPLIT_TPLINK_FW. But looking at
the image make recipe, there is no code that adds a TPLINK header.
So instead the board will use "denx,umimage". This requires
MTD_SPLIT_UIMAGE_FW, but this is present thanks to some NEC devices.
(Maybe the MTD_CONFIG_ARGS can be removed as well? But it could be
there because of the padding at the beginning. This needs testing.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
brings back the ath10k QCA9980 wifi nodes to which
it adds ASROCK's wifi calibration data. These are
now provided by the ath10k_firmware.git's board-2.bin.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
converts extraction entries from 11-ath10k-caldata into
nvmem-cells in the individual board's device-tree file.
The patch also moves previously existing referenced
nvmem-cells data nodes which were placed at the end
back into the partitions node. As well as removing
some duplicated properties from qcom-ipq8065-xr500.dts's
art (the included nighthawk.dtsi defines those already).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Commit d284e6ef0f ("treewide: convert mtd-mac-address-increment* to
generic implementation") renamed "mtd-mac-address-increment" property
to "mac-address-increment". Convert remaining usages that have been
added after that.
Fixes: f44e933458 ("ipq806x: provide WiFI mac-addresses from dts")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This moves bootargs-append support patch from ipq40xx and ipq806x to
generic. This way we can append additional boot arguments from DTS instead
of only being able to overwrite them.
This is a preparation for kirkwood support of ipTIME NAS1.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This board has 512MiB of RAM like the R7800, and the VDSL modem is
attached to the second PCIe port.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
