MT7981B /256MB /16MB SPI (XM25QH128C)
AX 2.4Ghz
AX 5Ghz 160Mhz wide
1Gbit LAN
OEM:
root@RE3000:~# ifconfig |grep HWaddr
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 (label)
br-wan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra2 Link encap:Ethernet HWaddr 82:XX:XX:28:XX:X0
rax0 Link encap:Ethernet HWaddr 82:XX:XX:38:XX:X0
rax2 Link encap:Ethernet HWaddr 82:XX:XX:58:XX:X0
OpenWrt
root@OpenWrt:/# ifconfig |grep HW
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy0-ap0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy1-ap0 Link encap:Ethernet HWaddr 82:XX:XX:08:XX:X1
tftp Installation via u-boot:
Connect TTL3.3V converter
connector is under the radiator Set speed 115200 8 N 1
Interrupt boot process by holding down-arrow key during boot then
>> 6. Load image
>> 0 - TFTP client (Default)
enter IP adresses and initramfs-kernel.bin
write to flash via sysupgrade or gui
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Now that we got fitblk_get_bootdev in /lib/upgrade/common.sh we don't
need platform_get_bootdev in each of the subtargets any longer.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use newly added support for NVMEM-on-UBI instead of extracting MAC
address and WiFi EEPROM data in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use newly added support for NVMEM-on-UBI instead of extracting MAC
address and WiFi EEPROM data in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use newly added support for NVMEM-on-UBI instead of extracting MAC
address and WiFi EEPROM data in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that we can reference MMC partitions in device tree, use that
to get rid of Wi-Fi EEPROM and MAC address setup in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware specification
----------------------
SoC: MediaTek MT7986A 4x A53
Flash: 128MB SPI-NAND, 8GB eMMC
RAM: 2GB DDR4
Ethernet: 2x 2.5GbE (Airoha EN8811H)
WiFi: MediaTek MT7976C 2x2 2.4G + 3x3 5G
Interfaces:
* M.2 Key-M: PCIe 2.0 x2 for NVMe SSD
* M.2 Key-B: USB 3.0 with SIM slot
* front USB 2.0 port
LED: Power, Status, WLAN2G, WLAN5G, LTE, SSD
Button: Reset, internal boot switch
Fan: PWM-controlled 5V fan
Power: 12V Type-C PD
Installation instructions for eMMC
----------------------------------
0. Set boot switch to boot from SPI-NAND (assuming stock rom or immortalwrt
running there).
1. Write GPT partition table to eMMC
Move openwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-gpt.bin to
the device /tmp using scp and write it to /dev/mmcblk0:
dd if=/tmp/openwrt-*-r3-mini-emmc-gpt.bin of=/dev/mmcblk0
2. Reboot (to reload partition table)
3. Write bootloader and OpenWrt images
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate partitions:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb of=/dev/mmcblk0p4
dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb of=/dev/mmcblk0p5
sync
4. Remove the device from power, set boot switch to eMMC and boot into
OpenWrt. The device will come up with IP 192.168.1.1 and assume the
Ethernet port closer to the USB-C power connector as LAN port.
5. If you like to have Ethernet support inside U-Boot (eg. to boot via
TFTP) you also need to write the PHY firmware to /dev/mmcblk0boot1:
echo 0 > /sys/block/mmcblk0boot1/force_ro
dd if=/lib/firmware/airoha/EthMD32.dm.bin of=/dev/mmcblk0boot1
dd if=/lib/firmware/airoha/EthMD32.DSP.bin bs=16384 seek=1 of=/dev/mmcblk0boot1
Installation instructions for NAND
----------------------------------
0. Set boot switch to boot from eMMC (assuming OpenWrt is installed there
by instructions above. Using stock rom or immortalwrt does NOT work!)
1. Write things to NAND
Move files to the device /tmp using scp:
- openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin
- openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
- openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
- openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
Write them to the appropriate locations:
mtd write /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin /dev/mtd0
ubidetach -m 1
ubiformat /dev/mtd1
ubiattach -m 1
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip)
ubimkvol /dev/ubi0 -N fip -n 0 -s $volsize -t static
ubiupdatevol /dev/ubi0_0 /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
cd /lib/firmware/airoha
cat EthMD32.dm.bin EthMD32.DSP.bin > /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -N en8811h-firmware -n 1 -s 147456 -t static
ubiupdatevol /dev/ubi0_1 /tmp/en8811h-fw.bin
ubimkvol /dev/ubi0 -n 2 -N ubootenv -s 126976
ubimkvol /dev/ubi0 -n 3 -N ubootenv2 -s 126976
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb)
ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
3. Remove the device from power, set boot switch to NAND, power up and
boot into OpenWrt.
Partially based on immortalwrt support for the R3 mini, big thanks for
doing the ground work!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Switch to all-UBI layout on SPI-NAND
* use fitblk driver instead of uImage.FIT partition parser
* adapt sysupgrade
* bump COMPAT_VERSION
Remove BROKEN mark now that all needed changes are done.
Boards running images generated before this commit will require
full reflash of the bootloader, re-install from SD card is the
easiest way to achieve that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
SOC: MediaTek MT7988A (4x Cortex-A73)
RAM: 4 GiB DDR4
Flash: 128 MiB Winbond SPI-NAND
MMC: 8 GiB eMMC *or* microSD (cannot be used both)
ETH: 4x 1GE (1x WAN, 3x LAN)
2x SFP+ (10G, 5G, 2.5G, 1G)
USB: on-board USB 3.2 4-port hub
1x USB 3.2 port (type A connector)
1x M.2 for 4G/5G modem
2x mPCIe for additional modems
WiFi: optional MediaTek MT7996 Wi-Fi 7 module
(using 2x PCIe gen3 x2 on the mPCIe slots and 12V power)
Installation
------------
1. Decompress and write the sdcard image to a micro SD card and use that
to boot the R4 (both dip switches in upper position).
2. Use the bootloader menu accessible via the serial console to install
to SPI-NAND.
3. Switch to boot from SPI-NAND and install to eMMC.
Known issues
------------
- The RST button is hard-wired to the SoC reset and can't be read
from software. This can be changed by modifying the board (ie.
moving a 0-ohm resistor). However, in order to maintain compatibility
with the board as it comes from factory the button isn't used by
OpenWrt and the WPS button is used as factory/reset button instead.
- various small things still need to be fixed in DT
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point.
Oem firmware is a custom openwrt 21.02 snapshot version.
We can gain access via ssh once we remove the root password.
Hardware specification:
SoC: MediaTek MT7981A 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN)
1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN)
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976D
LEDS: 1x (Red, Blue and Green)
Button: Reset
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC GND TX RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface (http://apipaddress/computer/login.html),
and download the
configuration(http://apipaddress/computer/config.html).
2. Rename downloaded backup config - 'backup.file to backup.tar.gz',
Enter 'fakeroot' command then decompress the configuration:
tar -zxf backup.tar.gz
3. Edit 'etc/shadow', update (remove) root password:
With password =
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
to
Without password =
'root::0:99999:7:::'
'root::0:99999:7:::'
4. Repack 'etc' directory back to a new backup file:
tar -zcf backup-ssh.tar.gz etc/
5. Rename new config tar.gz file to 'backup-ssh.file'
Exit fakeroot - 'exit'
6. Upload new configuration via web interface, now you
can SSH with the following:
'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'.
Backup the mtd partitions
- https://openwrt.org/docs/guide-user/installation/generic.backup
7. Copy openwrt factory firmware to the tmp folder to install via ssh:
'scp -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa \
*-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \
root@192.168.10.1:/tmp/'
'sysupgrade -n -F \
/tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin'
8. Once led has stopped flashing - Connect via ssh with the
default openwrt ip address - 'ssh root@192.168.1.1'
9. SSH copy the openwrt sysupgrade firmware and upgrade
as per the default instructions.
Signed-off-by: David Bentham <db260179@gmail.com>
This reverts commit dcdcfc1511.
This is a firmware for third-party u-boot mod, which should not
be carried here by us.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Setting/clearing bits on the first byte of the mac address causes collisions
when using multiple SSIDs on both PHYs. Change the allocation to alter the
last byte instead.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 16MB NOR
RAM: 256MB
Ethernet: 2x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
Power: DC 12V 1A, PoE 802.3af 48V
Flash instructions:
Option #1 - SSH
I was able to SSH into the stock firmware of my device.
1. Attach the router to the network
2. Use scp (-O) to copy the sysupgrade image
3. Connect using SSH and run `sysupgrade -n`
Option #2 - U-Boot
One way to use the bootloader for flashing is using TFTP:
1. Connect to the router using an ethernet cable
2 Spin up a TFTP server serving the sysupgrade file
3. Open the case and attach a UART
4. Attach power to the router and interrupt the countdown by pressing
any key
5. Select option #2 (Upgrade firmware)
6. Enter IP address information and image name
7. Wait patiently
Co-Authored-By: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
Co-Authored-By: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
(based on support for ASUS RT-AX59U by liushiyou006)
SOC: MediaTek MT7986
RAM: 512MB DDR4
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Upgrade from AsusWRT to OpenWRT using UART
Download the OpenWrt initramfs image.
Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to rtax59u.bin.
Connect the PC with TFTP server to the RT-AX59U.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted.
Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 rtax59u.bin
$ bootm 0x46000000
Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Upgrade from AsusWRT to OpenWRT using WebUI
Download transit TRX file from https://drive.google.com/drive/folders/1A20QdjK7Udagu31FSszpWAk8-cGlCwsq
Upgrade firmware from WebUI (192.168.50.1) using downloaded TRX file
Wait for OpenWRT to boot (192.168.1.1).
Upgrade system with sysupgrade image using luci or uploading it through scp and executing sysupgrade command
MAC Address for WLAN 5g is not following the same algorithm as in AsusWRT.
We have increased by one the WLAN 5g to avoid collisions with other networks from WLAN 2g
when bit 28 is already set.
: Stock : OpenWrt
WLAN 2g (1) : C8:xx:xx:0D:xx:D4 : C8:xx:xx:0D:xx:D4
WLAN 2g (2) : : CA:xx:xx:0D:xx:D4
WLAN 2g (3) : : CE:xx:xx:0D:xx:D4
WLAN 5g (1) : CA:xx:xx:1D:xx:D4 : CA:xx:xx:1D:xx:D5
WLAN 5g (2) : : CE:xx:xx:1D:xx:D5
WLAN 5g (3) : : C2:xx:xx:1D:xx:D5
WLAN 2g (1) : 08:xx:xx:76:xx:BE : 08:xx:xx:76:xx:BE
WLAN 2g (2) : : 0A:xx:xx:76:xx:BE
WLAN 2g (3) : : 0E:xx:xx:76:xx:BE
WLAN 5g (1) : 0A:xx:xx:76:xx:BE : 0A:xx:xx:76:xx:BF
WLAN 5g (2) : : 0E:xx:xx:76:xx:BF
WLAN 5g (3) : : 02:xx:xx:76:xx:BF
Signed-off-by: Xavier Franquet <xavier@franquet.es>
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit)
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
No. of Antennas: 6
Note: Upon opening the router, only 5 antennas were connected
to the mainboard.
Led Layout:
Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi
Buttons:
Reset-Mesh
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Signed-off-by: Ian Oderon <ianoderon@gmail.com>
The Bonanza Peak series are a couple of MT7986-powered 2.5 GBit/s
Wi-Fi 6 residential gateway, access point and mesh router products.
All of them come with an eMMC to boot from, are powered via USB-C and
got a USB 3.0 type-A port. All of them got a Dialog (Renesas) DA14531
Bluetooth module connected via UART. If the device was previously
running stock firmware, the BT chip's internal flash has been loaded
with firmware and it can be attached using hciattach when using
OpenWrt.
SOC: MediaTek MT7986A
RAM: 2 GiB DDR4
eMMC: 8 GiB
Bluetooth: BLE5 (DA14531)
Serial: 3.3V level, 115200 8n1 on 4-pin connector
* SDG-8612 - Dual-band RJ-45 gateway
2x 2.5G MaxLinear PHY for WAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8614 - Dual-band SFP gateway
1x SFP cage with up to 2.5G speed
1x 2.5G MaxLinear PHY for LAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8622 - Tri-band mesh router
2x 2.5G MaxLinear PHY
The MT7986 2G and 5G are used as 2G and 5G high band.
There’s a MT7915 PCIe card for 5G low band.
* SDG-8632 - Tri-band mesh router with 6 GHz
2x 2.5G MaxLinear PHY
The MT7986 serves the 2G and 6G bands.
There’s a MT7915 PCIe card for 5G.
Installation via U-Boot serial console:
0. setup TFTP server with IP 192.168.1.10/24, place initramfs image
renamed to openwrt.XXX where XXX is the internal product number:
SDG-8612: XXX = 412
SDG-8614: XXX = 414
SDG-8622: XXX = 422
SDG-8632: XXX = 432
1. connect to the serial console and power on the device.
Interrupt the bootloader by pressing 'st'
2. setenv boot_mode openwrt ; saveenv
3. run boot1
Load firmware via TFTP and write to flash
4. run boot2
Now OpenWrt initramfs should boot
5. upload sysupgrade.bin via scp to /tmp
6. sysupgrade
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acelink EW-7886CAX is an MT7986A (AKA Filogic 830) based access point.
It has 512 MiB of RAM, one 2.5 Gbps PoE (802.3at) Ethernet port and
on-SoC Wi-Fi. There is no printed MAC label (on my unit).
My unit came with Mediatek's firmware (based on OpenWrt 21.02)
installed. It was possible to simply upgrade using OpenWrt's sysupgrade
tool.
Another verified upgrade method is using U-Boot (requires UART). During
every boot there is "U-Boot Boot Menu". Selecting option "2. Upgrade
firmware" allows using U-Boot's tftp client to load and flash factory
image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Change permissions of the bootcount init script from old mode 100644
to new mode 100755 to ensure its executability.
Fixes: 6cc14bf66a ("filogic: support Telenor branded ZyXEL EX5700")
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Confiabits MT7981 is a Wi-Fi 6 router based on MediaTek MT7981.
Specification:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 256 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 4x 10/100/1000 Mbps MT7531AE (3xLAN, 1xWAN)
- USB 2.0 port
- Buttons: 1 Reset button, 1 Mesh button.
- LEDs: 7x light-blue, 2x warm-white
- Serial console: internal 4-pin header, 115200 8n1
- Power: 12 VDC, 1.5 A
MAC addresses in stock firmware and in this commit:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 00:0c:43:xx:xx:e1 | label+1 |
| LAN | 00:0c:43:xx:xx:e0 | label |
| WLAN 2g | 00:0c:43:xx:xx:e0 | label |
| WLAN 5g | 02:0c:43:xx:xx:e0 | |
+---------+-------------------+-----------+
The label MAC was found in 'Factory', 0x4
Installation:
The stock firmware is OpenWrt-based. If you can reach LuCI or SSH, just use the sysupgrade image
with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
Hardware
--------
SoC: MediaTek MT7981BA
RAM: 1GB DDR4 (NANYA NT5AD512M16C4-JR)
MMC: 8GB eMMC (Samsung 8GTF4R)
ETH: 1000Base-T LAN (ePHY)
2500Base-T WAN (MaxLinear GPY211C)
BTN: 1x Reset Button
LED: System (blue/white)
VPN (white)
USB: 1x USB-A (USB 3.0)
UART: 115200 8N1 - Pinout on board next to LAN port
Don't connect 3.3V!
Known Issues
------------
U-Boot vendor recovery does not seem to accept any images, neither
GL.iNet images nor OpenWrt images. Recovery requires serial access!
Installation
------------
Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to
not retain existing settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
The PGIO configuration should be added for the ZBT-Z8102AX and not the ZBT-Z8103AX
Fixes: c8c2f52262 ("mediatek: add support for Zbtlink ZBT-Z8102AX")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The flash procedure is similar to the Xiaomi AX6000 router.
Load openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb from original Zyxel U-Boot:
tftpboot openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
bootm 0x46000000
Load mtd-rw
insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1
Format ubi and create ubootenv partitions
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
Copy openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb to /tmp and create recovery partition.
If your recovery image is larger than 10MiB, size the recovery partition accordingly to make it fit.
ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
Copy preloader and uboot to /tmp and write them in the mtd
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip
Now write the firmware:
sysupgrade -n /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-squashfs-sysupgrade.itb
To create a correct BL2, I had to add a profile for 'spim:4k+256' as I could not find a way to value the variable 'NAND_TYPE'.
Features and fixes from hitech95 tree has been squashed, I'm attaching his commit message:
The Power LED was not working correctly and not reacting
to the boot process and statuses.
The board has space (footprint) for an unpopulated Zigbee chip,
while we dont know the device model having this chip populated
we have to assure that the common dts doesnt enable
interfaces that share pins with such device.
In this instance the PCIe and the uart1 and uart2 are disabled.
Some of the control PCIE pins seems to be used for the Zigbee chip,
UART1 seems to be used as a flash port while UART2 should be the
main comunication interface of Zigbee chip.
The Zigbee chip should be a EFR32MG21. But the pins used for UART
seems to be not on standard PINS used by other adapters.
So it cannot run firmwares shared on the web.
But it should be possible to build a custom firmware with
the corrtect pinmux.
This commit also contains the following squashed commit from hitech95
- mediatek: fix sysupgrade for Zyxel EX7601-T0 ubootmod
Changes and fixes added in common board:
- added aliases for boot status leds.
- added aliases for the mac-label-device.
- added pin claims for core features (MDIO and UART 0)
- added default LEDs configuration (01_leds)
- added default network configuration (02_network)
- added missing kmod-usb3 module for USB3
- fixed LED names
- fixed reset pin for SLIC chip
- removed unused pinmux configurations and devices
- fix LAN (switch) port numbering
- using nvmem cells for wifi eeprom, dropping deprecated "mediatek,mtd-eeprom"
- proper factory partition and mac address handling
- cleaned up spi_nand sections and partition
Changes and fixxes added in stock layout:
- added NMBM, if u-boot has it, the kernel must be informed.
Co-authored-by: Nicolò Veronese <nicveronese@gmail.com>
Co-developed-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by
Ian Ishmael C. Oderon.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: Winbond 128MB
RAM: DDR3 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
Power: DC 12V 1A
Flash instructions:
1. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
2. Attach UART, pause at u-boot menu.
3. Select "Upgrade ATF BL2", then use preloader.bin
4. Select "Upgrade ATF FIP", then use bl31-uboot.fip
5. Download the initramfs image, and type "reset",
waiting for tftp recovery to complete.
6. After openwrt boots up, perform sysupgrade.
Note:
1. Since NMBM is disabled, we must back up all partitions.
2. Although we can upgrade new firmware in the stock firmware,
we need the special fit image signature of MediaTek and
dual boot (hack kernel) to make u-boot boot it. So just
abandon these hacks and flash it via the serial port.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The router use mt7986_eeprom_mt7976_dual.bin
Fixes: d522ccecb2 ("filogic: add support for ASUS TUF AX6000")
Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
Hardware
========
SOC: MediaTek MT7986
RAM: 512MB DDR3
FLASH: 256MB SPI-NAND
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz 4T4R
ETH: MediaTek MT7530 Switch (LAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (WAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (LAN)
UART: 3V3 115200 8N1 (Do not connect VCC)
USB 3.1
Installation
============
Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to TUF-AX6000.bin.
Connect to the serial console, interrupt the auto boot process by
pressing '4' when prompted or press '1' and set client IP, server
IP and name of the image.
yOU don't need to open the case or even soldering anything.
use three goldpin wires, remove their plastic cover and connect
them to the console pinout via the case holes.
You can see three holes
From Bottom: RX, TX, Ground - partially covered
Download & Boot the OpenWrt initramfs image.
In case of option '4'
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 TUF-AX6000.bin
$ bootm 0x46000000
In case of option '1'
1: Load System code to SDRAM via TFTP.
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (TUF-AX6000.trx) ==:
Wait for OpenWrt to boot. Transfer the sysupgrade
image to the device using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
================
2.5Gb LAN port LED is ON during boot or when the LAN cable is disconnected
The cover yellow light is not supported. (only blue one)
Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 64GB eMMC or 128 MB SPI-NAND
RAM: 512MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
- UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | GND TX VCC RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
tar -zcf cfg_export_config_file.conf etc/
* If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.
Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH CMIIT ID: xxxx" is NAND version
eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
('data' partition can be ignored, it's useless.)
2. Write new GPT table:
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync
NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
mtd erase BL2
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
mtd erase FIP
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
ubidetach -p /dev/mtd0
ubiformat -y /dev/mtd0
ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Commit mt76: drop default eeprom file for mt7986-firmware
(e3aa645b26) breaks eeprom loading for
Mercusys MR90X v1. As a result WiFi is not working at all.
This commit adds Mercusus MR90x to the caldata script (it works after the
commit mentioned above). And we can safely drop "81_fix_eeprom" script
as it's no longer required.
Fixes: e3aa645b26
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Add build for the MTK3943 reference board for MT7981B+MT7976C.
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: various options
- RAM: 256MB DDR3
- Ethernet: 4 x 10/100/1000 Mbps via MT7531AE switch
EITHER 1 x 10/100/1000 Mbps built-in PHY
OR 1 x 10/100/1000/2500 Mbps MaxLinear GPY211C
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: RST, WPS
**Flash instructions for SPIM-NAND:**
- write *mt7981-rfb-spim-nand-preloader.bin to 'BL2' partition
- write *mt7981-rfb-spim-nand-bl31-uboot.fip to 'FIP' partition
- erase 'ubi' partition
- reset board
- create ubootenv and ubootenv2 UBI volumes in U-Boot
- edit environment and set bootcmd, e.g.
setenv bootconf 'config-1#mt7981-rfb-spim-nand#mt7981-rfb-mxl-2p5g-phy-eth1'
setenv bootcmd 'ubi read $loadaddr fit; bootm $loadaddr#$bootconf'
- load initramfs image via TFTP:
setenv serverip 192.168.1.254
setenv ipaddr 192.168.1.1
setenv bootfile openwrt-mediatek-filogic-mediatek_mt7981-rfb-initramfs.itb
saveenv ; saveenv
tftpboot
bootm $loadaddr#$bootconf
- Now use sysupgrade to write OpenWrt firmware to flash.
SNFI-NAND, SPIM-NOR and eMMC all work very similar, a bootable SD card image
is also being generated. However, as the board I've been provided only comes
with SPIM-NAND all other boot media are untested.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
| Layout: |
| :-------- |
| <Antenna> |
| VCC |
| GND |
| Tx |
| Rx |
**Flash instructions:**
1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.
**Notes:**
If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.
Signed-off-by: Patricia Lee <patricialee320@gmail.com>
The NMBM-Enabled layout did not use fit image,
it just need default process. So it was been removed in platform.sh.
It will fix sysupgrade error for xiaomi,mi-router-wr30u-112m-nmbm.
Signed-off-by: Hank Moretti <mchank9999@gmail.com>
When adapting the network configuration for MT7988 RFB a stray quote
was left in a script. Remove it to fix generating the default network
configuration.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Switch to OpenWrt uImage.FIT bootmethod and include various bootloader
artifacts with the generated binaries.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable building a factory image which can be flashed through the OEM
firmware's web interface. It seems that the web interface requires a
minimum file size of 10MiB, otherwise it will not accept the image.
The update image is a regular sysupgrade tarball packed in a Netgear
encrypted image. The Netgear encrypted image is the same as used in
WAX202 or WAX206, including the encryption keys and IV.
This adds a script which creates the rootfs_data volume on first
startup. This is required since the OEM firmware's sysupgrade scripts
do not create such a paritition. Note that any script ordered after
70_initramfs_test will not get executed on initramfs. Hence this new
script 75_rootfs_prepare won't create the rootfs_data volume when
using the recovery initramfs.
Also, this deletes the kernel_backup and rootfs_backup volumes in case
we have to create the rootfs_data volumes. This makes sure that
OpenWrt is the actual backup firmware instead of the stock firmware.
References in WAX220 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX220-V1.0.2.8-gpl-src.tar.gz
* package/base-files/files/lib/upgrade/nand.sh:186
Creation of rootfs_data is disabled
* Uboot-upstream/board/mediatek/common/ubi_helper.c
Automatic creation of UBI backup volumes
Signed-off-by: Stefan Agner <stefan@agner.ch>
Telenor quirks
--------------
The operator specific firmware running on the Telenor branded
ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt
installation.
Notable changes to U-Boot include
- environment is stored in RAM and reset to defaults when power
cycled
- dual partition scheme with "nomimal" or "rescue" systems, falling
back to "rescue" unless the OS signals success in 3 attempts
- several runtime additions to the device-tree
Some of these modifications have side effects requiring workarounds
- U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash
unless this node exists
- U-Boot verifies that the selected rootfs UBI volume exists, and
refuses to boot if it doesn't. The chosen "rootfs" volume must contain
a squashfs signature even for tftp or initramfs booting.
- U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr"
variable to the label mac. But "factoryparams" does not always
exist. Instead there is a "RIP" volume containing all the factory
data. Copying the "RIP" volume to "factoryparams" will fix this
Hardware
--------
SOC: MediaTek MT7986
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Mikron xxx)
WIFI: Mediatek MT7986 802.11ax 5 GHz
Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.2/24. Rename the image to C0A80101.img.
2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial
console, Interrupt the autoboot process by pressing ESC when prompted.
3. Download and boot the OpenWrt initramfs image.
$ env set uboot_bootcount 0
$ env set firmware nominal
$ tftpboot
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
----------------
- The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but
OpenWrt does not correctly configure the output.
- The "lan4" and "wan" port LEDs are driven by the GPH211C phys and
not configured by OpenWrt.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Implement the functionality of
target/linux/ramips/patches-5.15/700-net-ethernet-mediatek-support-net-labels.patch
in userspace, since the driver patch has been rejected as a generic solution:
https://github.com/openwrt/openwrt/pull/11435
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Hardware
--------
SOC: MediaTek MT7986A
RAM: 1GB DDR4
FLASH: 4GB eMMC
WiFi: 2x2 2.4 GHz 802.11 b/g/n/ax MT7916 DBDC
4x4 5 GHz 802.11 a/n/ac/ax MT7986
2x2 6 GHz 802.11ax MT7916 DBDC
ETH: 4x LAN 1Gbit/s (MT7531)
1x WAN 2.5Gbit/s (GPY211)
BTN: RESET, WPS
LED: Antenna LEDs (GPIO)
Mood-LED (Kinetic KTD2601) - unsupported
UART: Header nest to USB port - 3V3 115200 8N1
[BUTTON] GND - RX - TX [USB]
Installation
------------
1. Connect to the device using serial console.
2. Interrupt the Autoboot process when promted by sending '0' twice.
3. Serve the OpenWrt initramfs image using TFTP at 192.168.1.66. Name
the image "predator.bin" and conenct the TFTP server to the routers
LAN port.
4. Configure U-Boot to allow loading unsigned images from MMC
$ setenv bootcmd 'mmc read 0x40000000 0x00004400 0x0010000;
fdt addr $(fdtcontroladdr); fdt rm /signature; bootm 0x40000000';
saveenv
5. Transfer the image from U-Boot
$ setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1;
tftpboot 0x46000000 predator.bin; fdt addr $(fdtcontroladdr);
fdt rm /signature; bootm
6. Wait for OpenWrt to boot
7. Transfer the OpenWrt sysupgrade image to the router using scp.
8. Install OpenWrt using sysupgrade.
Signed-off-by: David Bauer <mail@david-bauer.net>
Changes introduced in commit 54dc1cde48 ("mediatek: filogic: add
support for Xiaomi WR30U") missed to end the case item with mandatory
`;;` which lead to a broken sysupgrade.
Fixes: 54dc1cde48 ("mediatek: filogic: add support for Xiaomi WR30U")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
