Commit Graph

23208 Commits

Author SHA1 Message Date
Petr Štetiar
c7b750e7ac treewide: kernel: drop redundant USB_EHCI_HCD=n config symbol
Commit e53ec043ba ("kirkwood: move usb support to modules") has moved
this config symbol into generic configs, so it could be removed from
other configs.

Suggested-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-09 10:28:40 +02:00
Sebastian Schaper
361c670a46 ath79: add support for D-Link DAP-1330/DAP-1365 A1
Port device support for DAP-1330 from the ar71xx target to ath79.

Additionally, images are generated for the European through-socket
case variant DAP-1365. Both devices run the same vendor firmware, the
only difference being the DAP_SIGNATURE field in the factory header.
The vendor's Web UI will display a model string stored in the flash.

Specifications:

 * QCA9533, 8 MiB Flash, 64 MiB RAM
 * One Ethernet Port (10/100)
 * Wall-plug style case (DAP-1365 with additional socket)
 * LED bargraph RSSI indicator

Installation:

 * Web UI: http://192.168.0.50 (or different address obtained via DHCP)
   There is no password set by default
 * Recovery Web UI: Keep reset button pressed during power-on
   until LED starts flashing red, upgrade via http://192.168.0.50
 * Some modern browsers may have problems flashing via the Web UI,
   if this occurs consider booting to recovery mode and flashing via:
   curl -F \
     files=@openwrt-ath79-generic-dlink_dap-1330-a1-squashfs-factory.bin \
     http://192.168.0.50/cgi/index

The device will use the same MAC address for both wired and wireless
interfaces, however it is stored at two different locations in the flash.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2020-07-09 10:28:40 +02:00
Sungbo Eo
358aec7775 ath79: add support for Arduino Yun
Arduino Yun is a microcontroller development board, based on Atmel
ATmega32u4 and Atheros AR9331.

Specifications:
- MCU: ATmega32U4
- SoC: AR9331
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: SoC internal
- Ethernet: 1x 10/100Mbps
- USB: 1x 2.0
- MicroSD: 1x SDHC

Notes:
- Stock firmware is based on OpenWrt AA.
- The SoC UART can be accessed only through the MCU.
  YunSerialTerminal is recommended for access to serial console.
- Stock firmware uses non-standard 250000 baudrate by default.
- The MCU can be reprogrammed from the SoC with avrdude linuxgpio.

Installation:
1.  Update U-Boot environment variables to adapt to new partition scheme.
    > setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
    > setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
    > saveenv
2.  Boot into stock firmware normally and perform sysupgrade with
    sysupgrade image.
    # sysupgrade -n -F /tmp/sysupgrade.bin

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-08 23:22:30 +02:00
David Woodhouse
af9932c9b7 mediatek: Implement sysupgrade support for Banana Pi R2
Based on work by Alexey Loukianov <lx2@lexa2.ru> and others.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
e19ffb25d9 mediatek: store MAC address in boot partition on Banana Pi R2
Like many boards, the Banana Pi R2 doesn't have permanant storage of
its MAC address, and we store the first random one that the kernel
generates in order to use it later and at least be consistent.

Store it in the FAT boot partition, just as the U7623 board (and others)
do.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
7adc29f59e mediatek: add SD card image creation for Banana Pi R2
Based on work by Alexey Loukianov <lx2@lexa2.ru> and others.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
91e43a1d7a mediatek: enable SATA for mt7623
The MT7623 SoC has the same SATA block as the MT7622, so enable it in
MT7623 builds too and add it to the DEVICE_PACKAGES for those boards.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
c848bc6cd5 mediatek/mt7623: unify features and packages, add ext4 and usb
The supported MT7623 boards are mostly identical (what with being a
System-on-Chip and all), so unify the DEVICE_PACKAGES for them, and add
ext4 and usb support for them.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
c07d0d7f3e mediatek: mt7623: refresh 5.4 kernel config
Some options were not explicitly specified, causing the kernel build to
drop to interactive mode. Set the missing options.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
Sebastian Schaper
14599c5945 ath79: add support for D-Link DCH-G020 Rev. A1
The DCH-G020 is a Smart Home Gateway for Z-Wave devices.

Specifications:

 * QCA9531, 16 MiB Flash, 64 MiB RAM
 * On-Board USB SD3503A Z-Wave dongle
 * GL850 USB 2.0 Hub (one rear port, internal Z-Wave)
 * Two Ethernet Ports (10/100)

Installation:

 * Web UI: http://192.168.0.60 (or different address obtained via DHCP)
   Login with 'admin' and the 6-digit PIN Code from the bottom label
 * Recovery Web UI: Keep reset button pressed during power-on
   until LED starts flashing red, upgrade via http://192.168.0.60
 * Some modern browsers may have problems flashing via the Web UI,
   if this occurs consider booting to recovery mode and flashing via:
   curl -F \
     files=@openwrt-ath79-generic-dlink_dch-g020-a1-squashfs-factory.bin \
     http://192.168.0.60/cgi/index

Known issues:

 * Real-Time-Clock is not working as there is currently no matching driver
   It is still included in the dts as compatible = "pericom,pt7c43390";
 * openzwave was tested on v19.07 (running MinOZW as a proof-of-concept),
   but the package grew too big as lots of device pictures were included,
   thus any use of Z-Wave is up to the user (e.g. extroot and domoticz)

The device will use the same MAC address for both wired and wireless
interfaces, however it is stored at two different locations in the flash.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2020-07-08 22:54:34 +02:00
John Audia
3e992ea790 ipq806x: compile in schedutil governor
Gives users a third option to augment ondemand and performance. Kernel
docs[1] explain differences and this PR empowers users w/ the choice to
select between the older ondemand and newer and more simplistic schedutil
should they wish to use one that is not the performance governor.

1. Documentation/admin-guide/pm/cpufreq.rst

Signed-off-by: John Audia <graysky@archlinux.us>
[fixed From: to match SoB:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 22:54:13 +02:00
Furkan Alaca
541faf2c93 ramips: mt7621: use lzma-loader for ra21s & rg21s
The rg21s fails to boot if the kernel is larger than about
2,376 KiB. The ra21s is virtually identical hardware.
Enabling lzma-loader resolves the issue on both the rg21s
and ra21s (see FS#3057 on the issue tracker).

Fixes: FS#3057
Signed-off-by: Furkan Alaca <furkan.alaca@queensu.ca>
2020-07-08 22:52:40 +02:00
Sergei Burakov
4dc9ad4af8 ramips: add support for ZyXEL Keenetic Lite Rev.B
Device specification:

SoC: RT5350
CPU Frequency: 360 MHz
Flash Chip: Macronix MX25L6406E (8192 KiB)
RAM: Winbond W9825G6JH-6 (32768 KiB)
5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
1x external antenna
UART (J1) header on PCB (57800 8n1)
Wireless: SoC-intergated: 2.4GHz 802.11bgn
USB: None
8x LED, 2x button

Flash instruction:

Configure PC with static IP 192.168.99.8/24 and start TFTP server.
Rename "openwrt-ramips-rt305x-zyxel_keenetic-lite-b-squashfs-sysupgrade.bin"
to "rt305x_firmware.bin" and place it in TFTP server directory.
Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
Router will download file from TFTP server, write it to flash and reboot.

Signed-off-by: Sergei Burakov <senior.anonymous@ya.ru>
2020-07-08 22:52:40 +02:00
Adrian Schmutzler
9e6257c26c ramips: move adslr_g7 in image/mt7621.mk to keep sorting
Move this device to the top to maintain alphabetic sorting in the
file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 21:20:19 +02:00
Adrian Schmutzler
7de08be913 ramips: add missing kmod-mt7615-firmware for TP-Link RE500 v1
Adding this has been overlooked when rebasing the commit prior to
merge.

Fixes: ba0f4f0cfd ("ramips: add support for TP-Link RE500 v1")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 21:20:19 +02:00
Adrian Schmutzler
f3921acdf0 ipq40xx: fix patches on dts Makefile
The patches for arch/arm/boot/dts/Makefile have not been updated
in a syntactically correct way (just body was changed). Fix it.

Fixes: 4a77a060ab ("ipq40xx: add support for Buffalo WTR-M2133HP")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 17:50:12 +02:00
Bjørn Mork
c1794d653c ramips: add support for ZyXEL WAP6805 (Altibox WiFi+)
Hardware
--------
SoC:   MediaTek MT7621ST
WiFi:  MediaTek MT7603
       Quantenna QT3840BC
Flash: 128M NAND
RAM:   64M
LED:   Dual colour red and green
BTN:   Reset
       WPS
Eth:   4 x 10/100/1000 connected to MT7621 internal switch
       MT7621 RGMII port connected to Quantenna module
GPIO:  Power/reset of Quantenna module

Quantenna module
----------------

The Quantenna QT3840BC (or QV840) is a separate SoC running
another Linux installation.  It is mounted on a wide mini-PCIe
form factor module, but is connected to the RGMII port of
the MT7621.  It loads both a second uboot stage and an os
image from the MT7621 using tftp.  The module is configured
using Quantenna specific RPC calls over IP, using 802.1q
over the RGMII link to support multiple SSIDs.

There is no support for using this module as a WiFi device
in OpenWrt. A package with basic firmware and management
tools is being prepared.

Serial ports
------------

Two serial ports with headers:

RRJ1 - 115200 8N1 - Connected to the Quantenna console
J1   -  57600 8N1 - Connected to the MT7621 console

Both share pinout with many other Zyxel/Mitrastar devices:

1 - NC (VDD)
2 - TX
3 - RX
4 - NC (no pin)
5 - GND

Dual system partitions
----------------------

The vendor firmware and boot loader use a dual partition
scheme storing a counter in the header of each partition. The
partition with the highest number will be selected for boot.

OpenWrt does not support this scheme and will always use the
first OS partition.  It will reset both counters to zero the
first time sysupgrade is run, making sure the first partition
is selected by the boot loader.

Installation from vendor firmware
---------------------------------

1. Run a DHCP server. The WAP6805 is configured as a client device
   and does not have a default static IP address. Make a note of
   which address it is assigned

2. tftp the OpenWrt initramfs-kernel.bin image to this address.
   Wait for the WAP6805 to reboot.

3. ssh to the OpenWrt initramfs system on 192.168.1.1. Make a
   backup of all mtd partitions now.  The last used OEM image is
   still present in either "Kernel" or "Kernel2" at this point,
   and can be restored later if you save a copy.

4. sysupgrade to the OpenWrt sysupgrade.bin image.

Installation from U-Boot
------------------------

This requires serial console access

1. Copy the OpenWrt initramfs-kernel.bin image as "ras.bin" to
   your tftp server directory.  Configure the server address as
   192.168.0.33/24

2. Hit ESC when the message "Hit ESC key to stop autoboot"
   appears

3. Type "ATGU" + Enter, and then "2" immediately after pressing enter.

4. Answer Y to the question "Erase Linux in Flash then burn new
   one. Are you sure?", and answer the address/filename questions.
   Defaults:
        Input device IP (192.168.0.2)
        Input server IP (192.168.0.33)
        Input Linux Kernel filename ("ras.bin")

5. Wait until after you see the message "Done!" and power cycle
   the device.  It will hang after flashing.

6. Continue with step 3 and 4 from the vendor firmware procedure.

Notes on the WAP6805 U-Boot
---------------------------
The bootloader has been modified with both ZyXELs zyloader and the
device specific dual partition scheme.  These changes appear to have
broken a few things.  The zyloader shell claims to support a number
of ZyXEL AT commands, but not all of them work.  The image selection
scheme is unreliable and inconsistent.  A limited U-Boot menu is
available - and used by the above U-Boot install procedure.  But
direct booting into an uploaded image does not work, neither with
ram nor with flash.  Flashing works, but requires a hard reset after
it is finished.

Reverting to OEM firmware
-------------------------

The OEM firmware can be restored by using mtd write from OpenWrt,
flashing it to the "Kernel" partition. E.g.

  ssh root@192.168.1.1 "mtd -r -e Kernel write - Kernel" < oem.bin

OEM firmwares for the WAP6805 are not avaible for public download,
so a backup of the original installation is required.  See above.

Alternatively, firmware for the WAP6806 (Armor X1) may be used. This
is exactly the same hardware.  But the branding features do obviously
differ.

LED controller
--------------

Hardware implementation is unknown.  The dual-color LED is controlled
by 3 GPIOs:

  4: red
  7: blinking green
 13: green

Enabling both red and green makes the LED appear yellow.

The boot loader enables hardware blinking, causing the green LED to blink
slowly on power-on, until the OpenWrt boot mode starts a faster software
blink.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
[fix alphabetic sorting for image build statement]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 16:07:05 +02:00
Pawel Dembicki
20c7abd4b7 ipq806x: add support for Linksys EA7500 V1
This patch adds support for the Linksys EA7500 V1 router.

Specification:
 - CPU: Qualcomm IPQ8064
 - RAM: 256MB
 - Flash: NAND 128MB
 - WiFi: QCA9982 an+ac + QCA9983 bgn
 - Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337)
 - USB: 1x USB 3.0 1x USB2.0
 - Serial console: RJ-45 115200 8n1 (1V8 Voltage level)
 - 2 Buttons
 - 1 LED

Known issues:
 - Some devices won't flash via web gui

Installation:
- Newer stock images doesn't allow to install custom firmware.
- Please downgrade software to 1.1.2 version. Official firmware:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img
- Do it two times to downgrade all stored images.
- Apply factory image via web-gui.

Serial + TFTP method:
 - downgrade to 1.1.2 two times
 - connect ehternet and serial cable
 - set ip address of tftp server to 192.168.1.254
 - put openwrt factory image to tftp folder and rename it to macan.bin
 - stop device while booting in u-boot
 - run command: "run flashimg"
 - run command: "setenv boot_part 1"
 - run command "saveenv"
 - reset

Back to stock:
- Please use old non-gpg image like this 1.1.2:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img
- ssh to router and copy image to tmp
- use sysupgrade -n -F

Tested by github users: @jack338c and @grzesiczek1

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 16:07:05 +02:00
Yanase Yuki
4a77a060ab ipq40xx: add support for Buffalo WTR-M2133HP
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.

Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A

Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
   and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
    # ubidetach -p /dev/mtd15
    # ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
    # fw_setenv bootcmd bootipq
8. Perform reboot.

Recover to stock firmware
-------------------------
1. Execute the following command.
    # fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2020-07-08 16:07:05 +02:00
Pawel Dembicki
d2c3131b3f kirkwood: add support for Zyxel NSA310S
Zyxel NSA310S is a NAS based on Marvell kirkwood SoC.

Specification:
 - Processor Marvell 88F6702 1 GHz
 - 256MB RAM
 - 128MB NAND
 - 1x GBE LAN port (PHY: Marvell 88E1318)
 - 2x USB 2.0
 - 1x SATA
 - 3x button
 - 7x leds
 - serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC)

Known issues:
 - no kernel module for RTC. [*]
 - buzzer (connected to MPP43) need to be drived by 1kHz signal
 - no kernel module for internal MCU connected via I2C[**]

[*]
Karoly Pocsi made simple, unofficial driver for HT1382.
It can be found here:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/

[**]
Karoly Pocsi found how CPU talk with MCU:
It is possible to query the MCU-controlled fan speed and temperature:
i2cget -y 0x0 0x0a 0x07
i2cget -y 0x0 0x0a 0x08
The first value (0x07) is the temperature in ° C, the second (0x08) is
the time in milliseconds to complete one fan revolution (rpm = 60,000 / value).
Info translated from:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/

Installation:

TFTP:
1. Run serial console and go to u-boot.
2. Copy u-boot via tftp and write to NAND:
	=> mw 0x0800000 0xffff 0x100000
	=> nand erase 0x0 100000
	=> setenv ipaddr 192.168.1.2
	=> setenv serverip 192.168.1.4
	=> tftp 0x0800000 nsa310s-u-boot.kwb
	=> nand write 0x0800000 0x0 0x100000
	=> reset
3. Run new u-Boot, repair bootcmd and restore MAC address from sticker
	=> setenv ethaddr AA:BB:CC:DD:EE:FF
	=> saveenv
4. Copy and run initramfs image
	=> setenv ipaddr 192.168.1.2
	=> setenv serverip 192.168.1.4
	=> tftpboot zyxel_nsa310s-initramfs-uImage
	=> bootm 0x800000
5. Download sysupgrade image and perform sysupgrade

USB:

1. Prepare usb fat32 drive with u-boot.kwb and initramfs image.
   Stick it to USB 2.0 port.
2. Run serial console and go to u-boot.
3. Copy u-boot from usb and write to NAND:
	=> mw 0x0800000 0xffff 0x100000
	=> nand erase 0x0 100000
	=> usb start
	=> fatload usb 0 0x0800000 u-boot.kwb
	=> nand write 0x0800000 0x0 0x100000
	=> reset
4. Run new u-Boot, repair bootcmd and restore MAC address from sticker
	=> setenv ethaddr AA:BB:CC:DD:EE:FF
	=> saveenv
5. Copy and run initramfs image:
	=> usb start
	=> fatload usb 0 0x0800000 initramfs-uImage
	=> bootm 0x800000
6. Download sysupgrade image and perform sysupgrade.

Based on work ThBexx <thomas.beckler@hotmail.com>
DTS based on dropped support in 0ebdf0c.

Tested-by: Lech Perczak <lech.perczak@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[NSA310s -> NSA310S in DEVICE_MODEL]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 16:07:05 +02:00
Andrey Bondar
ba59021d64 ath79: add support for 8devices Lima board
Specification:

  • 650/600/216 MHz (CPU/DDR/AHB)
  • 64 MB of RAM (DDR2)
  • 32 MB of FLASH
  • 2T2R 2.4 GHz
  • 2x 10/100 Mbps Ethernet
  • 1x USB 2.0 Host socket
  • 1x miniPCIe slot
  • UART for serial console
  • 14x GPIO

Flash instructions:

Upgrading from ar71xx target:

  • Upload image into the board:
    scp openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin
    root@192.168.1.1/tmp/
  • Run sysupgrade
    sysupgrade -F /tmp/openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin

Upgrading from u-boot:

  • Set up tftp server with
    openwrt-ath79-generic-8dev_lima-initramfs-kernel.bin
  • Go to u-boot (reboot and press ESC when prompted)
  • Set TFTP server IP
    setenv serverip 192.168.1.254
  • Set device ip from the same subnet
    setenv ipaddr 192.168.1.1
  • Copy new firmware to board
    tftpboot 0x82000000 initramfs.bin
  • Boot OpenWRT
    bootm 0x82000000
  • Upload image openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin into
    the board
  • Run sysupgrade.

Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
2020-07-08 16:07:05 +02:00
Sergio E. Nemirowski
645b1ec3e2 build: add 'make kernel_xconfig' command
This adds the kernel_xconfig make target.

Signed-off-by: Sergio E. Nemirowski <sergio@outerface.net>
2020-07-08 16:07:05 +02:00
Dongming Han
f103321349 ipq40xx: add support for GL.iNet GL-S1300
Specifications:
SOC:        Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core
RAM:        512 MiB
FLASH1:     16 MiB NOR - SPI0
FLASH2:     8 GiB eMMC
ETH:        Qualcomm QCA8075
WLAN1:      Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2
WLAN2:      Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2
INPUT:      Reset, WPS
LED:        Power, Mesh, WLAN
UART1:      On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
UART2:      On board with BLE module
SPI1:       On board socket for Zigbee module

Install via tftp
- NB: need to flash transition image firstly

Firstly install transition image:
(IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script

Secondly install openwrt sysupgrade bin:
(IPQ40xx) # run lf

Revert to factory image:
(IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script

The kernel and rootfs of factory firmware are on eMMC, and openwrt
firmware is on NOR flash. The transition image includes U-boot
and partition table, which decides where to load kernel and rootfs.
After you firstly install openwrt image, you can switch between
factory and openwrt firmware by flashing transition image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2020-07-08 16:07:05 +02:00
Emir Efe Kucuk
53a1fede1f ramips: Add support for Xiaomi Mi Router(Black,R2100)
The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many
characteristics (apart from its looks and the GPIO ports) with the 6-antenna
*white* "Xiaomi Redmi Router AC2100"

See the visual comparison of the two routers here:
https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg

Specification of R2100:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN in Yellow and Blue
- UART: On board (Don't know where is should be confirmed by anybody else)
- Modified u-boot

Hacking of official firmware process is same at both RM2100 and R2100.
Thanks to @namidairo

Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide
Guide is written for MacOS but it will work at linux.
needed packages: python3(with scapy), netcat, http server, telnet client

1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware
2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0

other than these I specified in here. Everything is same with:
f3792690c4
Thanks for all community and especially for this device:
@Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com)

MAC Locations:
WAN *:b5 = factory 0xe006
LAN *:b6 = factory 0xe000
WIFI 5ghz *:b8 = factory 0x8004
WIFI 2.4ghz *:b7 = factory 0x0004

Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com>
[refactored common image bits into Device/xiaomi-ac2100, fixed From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 16:07:05 +02:00
Thibaut VARÈNE
78fffc2dfd generic: platform/mikrotik: add partial AR71xx cpufreq support
This patch adds cpu frequency setting for AR724x and AR7161.
It is unknown if all the AR71xx devices support the same value range,
so support is only enabled for AR7161 at this stage.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-07-08 16:07:05 +02:00
Thibaut VARÈNE
a874c87f4c generic: platform/mikrotik: add board_revision tag
Tag was discovered exploring the hard_config of a "r2" board.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-07-08 16:07:05 +02:00
Thibaut VARÈNE
0217a9be0d generic: platform/mikrotik: graceful fallback for cpufreq_index
The current code would return an error on ath79 when the SoC isn't known
to the driver. Return the raw hex value instead, as happens with non
supported targets.
Also return the correctly incremented value from
sc_tag_cpufreq_ath79_arraysize()

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-07-08 16:07:05 +02:00
Thibaut VARÈNE
2714a4faab generic: platform/mikrotik: match RouterBOOT nomenclature
RouterBOOT cpu frequency settings are letter-indexed. Follow the
same logic for the sysfs interface.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-07-08 16:07:05 +02:00
Thibaut VARÈNE
5c4b431a3c generic: platform/mikrotik: fix routerboot_tag_show_u32s()
The routine would only accurately print out the first word.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fixes: 5ecf7d96 ("generic: routerboot sysfs platform driver")
2020-07-08 16:07:05 +02:00
Davide Fioravanti
8c13ebd3ad ramips: add support for Edimax Gemini RE23S
Hardware
--------
SoC:   Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM:   128MB
FLASH: 16MB NOR (Macronix MX25L12805D)
ETH:   1x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
  - 2.4GHz: 1x MT7615 (4x4:4)
  - 5GHz:   1x MT7615 (4x4:4)
  - 4 antennas: 2 external detachable and 2 internal
BTN:
  - 1x Reset button
  - 1x WPS button
LEDS:
  - 1x Green led (Power)
  - 1x Green-Amber-Red led (Wifi)
UART:
  - 57600-8-N-1

Everything works correctly.

Installation
------------
Flash the factory image directly from OEM web interface.
(You can login using these credentials: admin/1234)

Restore OEM Firmware
--------------------
Flash the OEM "bin" firmware directly from LUCI.
The firmware is downloadable from the OEM web page.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Restoring procedure tested with RE23_1.08.bin

MAC addresses
-------------
factory 0x4     *:24
factory 0x8004  *:25
Cimage  0x07    *:24
Cimage  0x0D    *:24
Cimage  0x13    *:24
Cimage  0x19    *:25

No other addresses were found in factory partition.

Since the label contains both the 2.4GHz and 5GHz mac address I decided
to set the 5GHz one as label-mac-device. Moreover it also corresponds
to the lan mac address.

Notes
-----
The wifi led in the OEM firmware changes colour depending on the signal
strength. This can be done in OpenWrt but just for one interface.
So for now will not be any default action for this led.

If you want to open the case, pay attention to the antenna placed on
the bottom part of the front cover.
The wire is a bit short and it breaks easily. (I broke it)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[fix two typos and add extended MAC address section to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 13:28:17 +02:00
Hauke Mehrtens
66e04abbb6 ar71xx: Fix mikrotik NAND compile problem
This Fixes the folowing compile error:
drivers/mtd/nand/rb91x_nand.c: In function 'rb91x_nand_remove':
drivers/mtd/nand/rb91x_nand.c:445:16: error: 'rbni' undeclared (first use in this function)
  nand_release(&rbni->chip);

Fixes: ce958dd88a ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-07 23:38:10 +02:00
Petr Štetiar
ae2d249056 ath79: nand: disable images for glinet_gl-ar750s
Fixes following build failures:

 WARNING: Image file glinet_gl-ar750s-nor-kernel.bin is too big
 WARNING: Image file glinet_gl-ar750s-nor-nand-kernel.bin is too big

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-07 19:47:24 +02:00
Andrey Bondar
326e488c7b ath79: add support for 8devices Rambutan board
Rambutan is a Wifi module based on QCA9550/9557
http://www.8devices.com/products/rambutan

Specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of DDR2 RAM
- 128 MB of NAND Flash
- 1x 100Mbps Ethernet
- 1x 1000Mbps Ethernet (PHY on dev-kit)
- 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz
- 2x U.FL connectors on module, chip antennas on dev-kit
- 1x miniPCIe slot
- 2x USB2.0 host
- 2x UART
- SPI, I2C, GPIO

Flash instructions:

Upgrade from ar71xx target:
 sysupgrade -F /tmp/openwrt-ath79-nand-8dev_rambutan-squashfs-sysupgrade.tar
or upgrade from GUI (don't save config)

Use factory image to flash from U-Boot:
 tftpboot 80060000 openwrt-ath79-nand-8dev_rambutan-squashfs-factory.ubi
 nand erase.part ubi
 nand write 80060000 ubi ${filesize}

Signed-off-by: Petr Štetiar <ynezz@true.cz> [copy&pasted missing commit description]
Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
2020-07-07 19:47:24 +02:00
Adrian Schmutzler
7cb721c03f ramips: use WiFi LED DT triggers for TP-Link RE650 v1
This moves WiFi LED triggers from 01_leds to device tree.

While at it, convert the labels there to lower case; this is
more commonly used and the change will actually remove competition
between DT trigger and leftover uci config on already installed
systems.

Suggested-by: Georgi Vlaev <georgi.vlaev@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-07 11:57:48 +02:00
David Bauer
d8ab3216e6 ath79: switch to kernel 5.4
As the reported major bugs are ironed out, switch to the new kernel to
begin testing with a broader audience.

Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-07 10:33:17 +02:00
Aleksander Jan Bajkowski
f496939f15 lantiq: set port numbers corresponding to reg value
Fix inconsistencies found in DTS files and sort ethernet ports based on
updated names.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[squash two separate patches, rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-07 01:03:59 +02:00
Aleksander Jan Bajkowski
3866fefa38 lantiq: remove redundant includes from fritz736x DTS files
The removed lines are already included in vr9_avm_fritz736x.dtsi

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-07 00:59:51 +02:00
Christoph Krapp
ba0f4f0cfd ramips: add support for TP-Link RE500 v1
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.

Hardware specification:

- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
  Serial console @ 57600,8n1

Flash instructions:

Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.

TFTP recovery to stock firmware:

Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-07 00:40:04 +02:00
Martin Blumenstingl
982468de35 lantiq: dts: Move the &usb_vbus nodes out of &gpio
Move the USB VBUS regulator nodes out of the GPIO controller node. This
fixes a problem where the "regulator-fixed" driver wasn't probed for
these regulators because the GPIO driver doesn't scan the child-nodes
and based on the dt-bindings documentation it's not supposed to.

This fixed the following error reported by Luca Olivetti:
  ...
  dwc2 1e101000.usb: DWC OTG Controller
  dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
  dwc2 1e101000.usb: irq 62, io mem 0x1e101000
  dwc2 1e101000.usb: startup error -517
  dwc2 1e101000.usb: USB bus 1 deregistered
  dwc2 1e101000.usb: dwc2_hcd_init() FAILED, returning -517

Fixes: FS#1634
Cc: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2020-07-06 20:23:33 +02:00
Matthew Gyurgyik
bb14d44039 kernel/pcengines-apu2: detect apuv4 board
Upstream commit 3d00da1de3 ("platform/x86: pcengines-apuv2: detect apuv4
board")

On 5.4, this module fails on APUv4 due to non-matching DMI data. With this
patch, the module will match DMI data for the APUv4.

Signed-off-by: Matthew Gyurgyik <matthew@gyurgyik.io>
[include upstream patch description]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-06 17:57:33 +02:00
Lars Wessels
f855eb91b3 lantiq: added switch-config for ARV752DPW
Add missing switch config (4 LAN-Ports + CPU).

Grey WAN port (used for ADSL) is not part of the switch.

Signed-off-by: Lars Wessels <software@bytebox.org>
[rework commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-06 17:57:24 +02:00
Lars Wessels
702366a30b lantiq: wifi mac fix for ARV752DPW
Set wifi mac from flash partition 'board_config' to
match the label on the device (Easybox 802).

Currently the wifi mac is always set to 00:0c:43:28:60:00.
eth0 and WiFi will now share the same mac (as in original firmware).

Signed-off-by: Lars Wessels <software@bytebox.org>
[improve commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-06 17:57:13 +02:00
Sunguk Lee
2d378703f1 ramips: reduce spi-max-frequency for ipTIME A8004T
Reduce spi-max-frequency for ipTIME A8004T and disable
m25p,fast-read option.

A8004T uses `en25qh128` for the MTD.
This flash memory would allow 80MHz, sometimes kernel received
wrong id value in initramfs installed router.
(kernel expected `1c 70 18 1c 70 18`, but one of cases, it
was `9c 70 18 1c 70 18`)

In this case, openwrt can't detect the partition information,
it would write the inccorect data to the firmware partition and
also it would occur the bootlooping after sysupgrade.

Signed-off-by: Sunguk Lee <d3m3vilurr@gmail.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-06 16:25:32 +02:00
Adrian Schmutzler
883250014d ipq806x: move serial0 to DTSI files
All device DTS files in the target set the serial0 property to the
same value (*). So, let's move the definitions to the DTSI files.

That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).

* The only exception is ipq8064-db149, which defines
  "serial0 = &uart2;", but inside a block called "alias" instead of
  "aliases". It must be assumed that this is broken anyway, so we
  don't touch it here.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-06 16:24:30 +02:00
Adrian Schmutzler
74e339f118 ipq806x: move stdout-path to DTSI files
All device DTS files in the target set the stdout-path to the same
value. So, let's move the definitions to the DTSI files.

That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-06 16:23:23 +02:00
Adrian Schmutzler
ed761344d2 ipq806x: disentangle and clean up SoC DTSI files
So far, the DTSI files on ipq806x had a linear inheritance:

  qcom-ipq8064.dtsi
  v
  qcom-ipq8064-v1.0.dtsi
  v
  qcom-ipq8064-v2.0.dtsi
  v
  qcom-ipq8065.dtsi

This poses problems when one wants to set something that is specific
to an architecture closer to the top of the tree.

In this patch, we remove the chain-like inheritance and have all
other files derived from qcom-ipq8064.dtsi (changing this name to
something more generic is not possible due to upstream use).

The removal of inheritance will require a few entries to be copied
from qcom-ipq8064-v2.0.dtsi to qcom-ipq8065.dtsi. However, it also
opens an opportunity for some clean-up:

- Many definitions can be improved by just using the innermost labels.

- Instead of disabling the CPU_SPC node for ipq8065, it is now off by
  default and enabled where needed.

- Instead of patching phy-tx0-term-offset into qcom-ipq8064.dtsi and
  then having it changed for qcom-ipq8064-v2.0/qcom-ipq8065, just have
  the appropriate settings done in the lower DTSI files directly.

- For the opp_table0 adjustments for ipq8065, just redefine what's
  changed, but don't add all the untouched properties again.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-06 16:21:15 +02:00
Sungbo Eo
19c8f11d92 ipq806x: move common pinmux nodes to SoC DTSI
As almost same pinmux nodes are repeated in each device dts,
let's define them once in the ipq8064 dtsi and remove the rest.

* uart0_pins : Did not touch.
* i2c4_pins  : This node seems to be not used at all in dts.
               Added the most common form in the dtsi. Did not touch rpm_pins.
* spi_pins   : The common mux node is already present in the dtsi.
               Removed the duplicate nodes from dts.
* nand_pins  : Moved the entire node.
* mdio0_pins : Moved the common mux node.
* rgmii2_pins: Moved the common mux node. "pins" property is overrided in ap161.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-06 16:08:18 +02:00
Hauke Mehrtens
014d3f593a ar71xx: Fix mikrotik NAND compile problem
There is one closing bracket too much.

Fixes: ce958dd88a ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-06 00:07:38 +02:00
Scott Roberts
d31bbe40e2 mvebu: config define i2c pxa slave
We are setting CONFIG_I2C_PXA is not set
If you do set pxa to y then you have issues if you do not have
CONFIG_I2C_PXA_SLAVE is not set

Fixes: dd13add3ce ("kernel: i2c-pxa: remove slave")
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
2020-07-04 21:12:42 +02:00
Daniel González Cabanelas
a902e6a657 mvebu: LS421DE: use automatic fan control with thermal zones
The Buffalo Linkstation LS421DE has a chassis fan for cooling two internal
hard drives. Currently there is no control over this fan, running always
at fixed medium speed.

With the recent jump to the kernel 5.4, now we can monitor the hard drive
temperature and control the fan with thermal zones.

Install the kmod-hwmon-drivetemp module and wire up a thermal zone on the
dts file to allow automatic fan control by the kernel.

Tested succesfully using a single Crucial BX500 SSD drive.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-07-04 21:12:42 +02:00