Specifications:
SOC: QCA9563 775 MHz + QCA9880
Switch: QCA8337N-AL3C
RAM: Winbond W9751G6KB-25 64 MiB
Flash: Winbond W25Q128FVSG 16 MiB
WLAN: Wi-Fi4 2.4 GHz 3*3 + 5 GHz 3*3
LAN: LAN ports *4
WAN: WAN port *1
Buttons: reset *1 + wps *1
LEDs: ethernet *5, power, wlan, wps
MAC Address:
use address source1 source2
label 40:9b:xx:xx:xx:3c lan && wlan u-boot,env@ethaddr
lan 40:9b:xx:xx:xx:3c devdata@0x3f $label
wan 40:9b:xx:xx:xx:3f devdata@0x8f $label + 3
wlan2g 40:9b:xx:xx:xx:3c devdata@0x5b $label
wlan5g 40:9b:xx:xx:xx:3e devdata@0x76 $label + 2
Install via Web UI:
Apply factory image in the stock firmware's Web UI.
Install via Emergency Room Mode:
DIR-859 A1 will enter recovery mode when the system fails to boot
or press reset button for about 10 seconds.
First, set computer IP to 192.168.0.5 and Gateway to 192.168.0.1.
Then we can open http://192.168.0.1 in the web browser to upload
OpenWrt factory image or stock firmware. Some modern browsers may
need to turn on compatibility mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 0ffbef9317)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
1. Remove unnecessary new lines in the dts.
2. Remove duplicate included file "gpio.h" in the device dts.
3. Add missing button labels "reset" and "wps".
4. Unify the format of the reg properties.
5. Add u-boot environment support.
6. Reduce spi clock frequency since the max value suggested by the
chip datasheet is only 25 MHz.
7. Add seama header fixup for DIR-859 A1. Without this header fixup,
u-boot checksum for kernel will fail after the first boot.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit e5d8739aa8)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch enables NVMEM u-boot-env driver (COFNIG_NVMEM_U_BOOT_ENV) on
generic subtarget to use from devices, for MAC address and etc.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(cherry picked from commit e8f7957450)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The x86_64 UML target wants to include SSSE3 optimized
crypto code which lives under /arch/x86/crypto.
However, these are not built and this causes an error.
| ERROR: module '[...]/arch/x86/crypto/sha512-ssse3.ko' is missing.
| make[3]: *** [modules/crypto.mk:990: [...]/kmod-crypto-sha512_5.15.112-1_x86_64.ipk] Error 1
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 959563fb81)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
the UML build fails during the kernel build:
| arch/um/drivers/net_kern.c: In function 'compute_hash':
| arch/um/drivers/net_kern.c:322:1: error: the frame size of 1072 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
| 322 | }
| | ^
|cc1: all warnings being treated as errors
The compute_hash() function is added by our patch:
102-pseudo-random-mac.patch
Instead of allocating a 1024 byte buffer on the stack for the SHA1
digest input, let's allocate the data on the heap. We should be
able to do that since crypto_alloc_ahash and ahash_request_alloc
also need to allocate structures on the heap.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit aed2569d37)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
That was a workaround for OpenWrt generation of config files. This patch
was used to postpone returning from probe function until loading
firmware and calling register_wiphy().
All of that is not needed anymore thanks to the ieee80211 hotplug.d
script introduced in the commit 5f8f8a3661 ("base-files, mac80211,
broadcom-wl: wifi detection and configuration"). That takes care of
generating /etc/config/wireless entries even if wireless device appears
late in the booting process.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit bd26266314)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently, SSDK is rather special in the sense that its not being built as
a proper out of tree module at all but rather like a userspace application
and that involves a lot of make magic which unfortunately broke with make
version 4.4 and newer.
Luckily QCA finally added a way to build SSDK as an out of tree module
and it uses the kernel buildsystem which makes it compile with make 4.4
as well.
So lets backport the support for it and switch to using it.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 957f1ee85e)
Currently all 23.05 related CI jobs are failing as the containers are
not available, so lets fix it by pushing those containers when the
version.mk changes.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 8fc2a0f00f)
Tony has reported, that CI tools job is failing for him in macOS
container due to prereq check failure for GNU `install` utility.
Michael diagnosed it and from his traces it was clear, that the issue is
caused by a wrong return value in the success check case, so lets fix it
accordingly.
Fixes: f75204036c ("prereq-build: allow host command symlinks to update")
Reported-by: Tony Ambardar <itugrok@yahoo.com>
Diagnosed-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 7855378fcd)
This reverts commit 3b68fb57c9.
After refactoring build checks to update old symlinks,
and after a long time of no python 2 support,
this is no longer needed.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit e2f9fa4204)
This makes the prereq stage update the symlinks
installed into staging_dir/host/bin
by rearrainging the way they are verified.
Before, seeing or installing a symlink would result in
a successful exit code, and not installing a symlink
would result is a failed exit code. However,
that is not able to account for the difference
between existing good and bad links, or whether
the link would be the same if it was reinstalled,
because the check can match the program to a different path.
Instead, let a success exit code represent
identifying an existing symlink as exactly the same
as what would be installed if it did not exist,
and let a fail exit code represent
needing to install the symlink
or not having a match to the check criteria.
The failing exit code is caught by a new second attempt
for all of the check-* targets which will then indicate
to the user that there was an update by having a success
exit code when the check is run again and the link is the same.
When there is nothing to update, the checks will run only once.
This relies on the ls command to be POSIX-conformant with long format:
"path/to/link -> target/of/link"
Also, make sure the symlink is executable, not just a file,
and the directory only needs to be created once.
Fixes: #12610
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit f75204036c)
Commit 54070a1 was added to allow building proper SDKs with kernels <
5.10. Now that all targets use at least kernel 5.10 it can be reverted.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
IGD is only useful when accelerating a VM guest that wants to direct
render to memory in the host's framebuffer, but since OpenWrt
typically runs on headless hardware, this serves no purpose.
Also build vfio with VFIO_NOIOMMU undefined (to get all of the code
enabled), but allow it to be enabled via boot-time modparams
settings (or at run-time via sysfs writes to
"/sys/module/vfio/parameters/enable_unsafe_noiommu_mode".
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
The PHY name has been changed to "mt7530-0" since IRQ support
was added to MT7530 driver.
Fixes: f9cfe7af1f ("kernel: backport MT7530 IRQ support")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
(node names, added color, function+function-enumerator properties)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
adds ForceCommand option. If the command is specified,
it forces users to execute the command when they log in.
Signed-off-by: Nozomi Miyamori <inspc43313@yahoo.co.jp>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The Sophos SG/XG-135 revision 3 has odd numbering of eth ports
where the WAN port (as marked on the case) is:
`eth6` and `eth0`, `eth1`, `eth2`, `eth3`, `eth5`, `eth7`, `eth8` are LAN ports.
Port `eth4` seems to be the SFP port.
Also add the missing LED definition for supported Sophos devices.
Original discussion at:
https://forum.openwrt.org/t/openwrt-on-revision-3-of-sophos-desktop-appliances/152912
Signed-off-by: Stan Grishin <stangri@melmac.ca>
A missing '\' caused the remaining parameters not to be passed to make.
This fixes the following error:
| gcc -c [...] fiptool.c -o fiptool.o
| In file included from fiptool.h:16,
| from fiptool.c:19:
|fiptool_platform.h:19:11: fatal error: openssl/sha.h: No such file or directory
| 19 | # include <openssl/sha.h>
| | ^~~~~~~~~~~~~~~
|compilation terminated.
|make[3]: *** [Makefile:58: fiptool.o] Error 1
as the HOST_CFLAGS are no longer passed.
then, HOST_CFLAGS is specified as a command argument, this
is a specific problem of our built since appending these
needs the override directive.
Fixes: df28bfe03247 ("tfa-layerscape: Change to github and use the latest tag")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Some U-Boot checks for a specified uImage time and refuses to boot if
mismatched. This patch fixes it by recognizing UIMAGE_TIME parameter.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Iomega Storcenter ix4-200d is a four-bay SATA NAS powered by a Marvell
Kirkwood SoC clocked at 1.2GHz. It has 512MB of RAM and 32MB of
flash memory, 3x USB 2.0 and 2x 1Gbit/s NIC
Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1200Mhz
- Flash size: 32 MiB
- RAM: 512MB
- LAN: 2x 1Gbit/s
- 3x USB 2.0
Notes:
- The blue drive LED is triggered by HDD activity, it can not be controlled
via GPIO.
- The LCD screen requires proprietary code and does not function at this time.
- Due to a kernel-related issue with the Marvell 88SE6121 SATA controller,
currently only trays numbered #3 and #4 work, #1 and #2 do not. [1]
Serial pinout:
CN4
--------------
| 10 8 6 4 2 |
| 9 7 5 3 1 |
-------------- PIN 1 Mark (fat line)
1 = RXD
4 = TXD
6 = GND
9 = 3.3V (not necessary to connect)
Installation instructions:
1. download initramfs-uImage and copy into tftp server
2. connect the tftp server to network port #1
3. access uboot environment with serial cable and run
setenv mainlineLinux yes
setenv arcNumber 1682
setenv console 'console=ttyS0,115200n8'
setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
setenv bootargs_root 'root='
setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
saveenv
setenv serverip 192.168.1.1
setenv ipaddr 192.168.1.2
tftpboot 0x00800000 [initramfs-uImage filename]
bootm 0x00800000
4. connect to LAN on network port #2, log into openwrt and sysupgrade to install into flash
[1] https://bugzilla.kernel.org/show_bug.cgi?id=216094
Signed-off-by: Sander van Deijck <sander@vandeijck.com>
(aligned FROM from signed-off. LED+key rename, whitespace removal)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This removes unneeded kernel version switches from the targets after
kernel 5.10 has been dropped.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
The default location of tfa-layerscape has been changed from
codeuaurora to github. Also use the latest tag for Layerscape
Linux Development POC from NXP.
v2:
* restored ls1021a-afrdm board
* added platform defines to fiptool so ls-ddr-phy can be built
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of ppfe-firmware has been changed
from codeuaurora to github. Also use the latest tag for
Layerscape Linux Development POC from NXP.
Tested on:
* NXP FRWY-LS1012A
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of fman-ucode has been changed from
codeuaurora to github. Also use the latest tag for Layerscape
Linux Development POC from NXP.
Tested on:
* NXP LS1046A-RDB
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of uboot-layerscape has been changed
from codeuaurora to github. Also use the latest tag for
Layerscape Linux Development POC from NXP.
Tested on:
* NXP FRWY-LS1012A
* NXP LS1028A-RDB
* NXP LS1046A-RDB
V2: Remove ls1028ardb specifix fixups not needed with new uboot
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of ls-rcw has been changed from codeuaurora
to github. The reason is that the old codeaurora source no longer
resolves. Also use the latest tag for Layerscape Linux Development
POC from NXP.
Tested on:
* NXP FRWY-LS1012A
* NXP LS1046A-RDB
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE, Mention that previous codeaurora source is
no longer available)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Prevents subshell commands from failing to parse options
when having defined a whitespace in the VERSION_DIST.
As the called resulting images unlikely will handle
whitespace correctly, we replace them by "-".
Signed-off-by: Sven Roederer <S.Roederer@colvistec.de>
Recently, a strange variant of ZTE MF286 was discovered, having QCA9886
radio instead of QCA9882 - like MF286A, but having MF286 flash layout
and rest of hardware.
To support both variants in one image, bind calibration data at offset
0x5000 both as "calibration" and "pre-calibration" nvmem-cells, so
ath10k can load caldata for both at runtime.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Specifications
The D-Link EXO AC1750 (DIR-869) router released in 2016.
It is powered by Qualcomm Atheros QCA9563 @ 750 MHz chipset, 64 MB RAM and 16 MB flash.
10/100/1000 Gigabit Ethernet WAN port
Four 10/100/1000 Gigabit Ethernet LAN ports
Power Button, Reset Button, WPS Button, Mode Switch
Flashing
1. Upload factory.bin via D-link web interface (Management/Upgrade).
Revert to stock
Upload original firmware via OpenWrt sysupgrade interface.
Debricking
D-Link Recovery GUI (192.168.0.1)
Signed-off-by: Jan Forman <forman.jan96@gmail.com>
For D-link DIR-859 and DIR-869
Replace the mtd-cal-data by an nvmem-cell.
Add the PCIe node for the ath10k radio to the devicetree.
Thanks to DragonBlue for this patch
Signed-off-by: Jan Forman <jforman@tuta.io>
gpio-export for the switch reset pin replaced with a reset pin definition for the driver, within the phy node.
Signed-off-by: Jan Forman <forman.jan96@gmail.com>
Tested-By: Sebastian Schaper <openwrt@sebastianschaper.net>
The 'KERNEL' is not referenced by other objects, so double '$$' will
cause shell unable to parse the variable 'BLOCKSIZE':
dd ... bs=$(BLOCKSIZE) conv=sync
bash: line 1: BLOCKSIZE: command not found
Fixes: 09a0efbe83(ramips: set default BLOCKSIZE to 64k for nor flash devices)
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The getrandom syscall is not hanging at bootup any more if there is
not enough entropy. This was fixed upstream in 2018 in commit:
a9cf659e05
This OpenWrt patch is not needed any more.
This reverts commit e64463ebde ("util-linux: avoid using the getrandom syscall")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the following error:
* check_data_file_clashes: Package taskset wants to install file build_dir/target-powerpc_8548_musl/root-mpc85xx/usr/bin/taskset
But that file is already provided by package * busybox
* opkg_install_cmd: Cannot install package taskset.
Fixes: 3c3d797c4d ("busybox: enable taskset by default")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes errors in the form of:
/Users/user/src/openwrt/openwrt/build_dir/hostpkg/json-c-0.16/json_util.c:63:35: error: a function declaration without a prototype is deprecated in all versions of C [-Werror,-Wstrict-prototypes]
const char *json_util_get_last_err()
^
void
1 error generated.
ninja: build stopped: subcommand failed.
Reported-by: Paul Spooren <mail@aparcar.org>
Suggested-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Remove upstramed patches:
- 100-configure.ac-fix-AC_ARG_WITH.patch
- 101-configure.ac-fix-cross-compilation.patch
Remove deprecated f2fstat tool:
https://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs-tools.git/commit/?id=77bf7ed29f1dd1341079913f3b36fc62f812c4f5
Changelog:
06c027a f2fs-tools: upgrade version 1.16.0
542cc57 fsck.f2fs: fix sanity check logic for cp_payload
a7df89e mkfs.f2fs: remove indentation
c82985a fsck.f2fs: don't call report_zone on normal partition
0ac168e f2fs-tools: relax zone size of power of 2
641be32 mkfs.f2fs: trim all the devices except the first one
3835fef f2fs-tools: fix # of total segments
5b08ca9 f2fs_io: support AES_256_HCTR2
ae3301c f2fs_io: Fix out of tree builds
ddbde27 fsck.f2fs: relocate chksum verification step during f2fs_do_mount()
77bf7ed f2fs-tools: Remove deprecated f2fstat
fb6575e Remove sg_write_buffer
1bb669e fsck.f2fs: avoid uncessary recalculation
ccd2361 fsck.f2fs: fix potential overflow of copying i_name
cd6b133 fsck.f2fs: add parentheses for SB_MASK
399600a dump.f2fs: remove unavailable option -g
3e6e178 f2fs-tools: define HAVE_CLOCK_GETTIME properly
907b972 f2fs-tools: support F2FS_IOC_START_ATOMIC_REPLACE
9ff70fb f2fs-tools: give less overprovisioning space
844f821 f2fs-tools: set host-aware zoned device similar to host-managed one
88ac76d fsck.f2fs: fix missing to assign c.zoned_model
8cbe34e fsck.f2fs: trigger repairing if filesystem has inconsistent errors
2f1dde2 fsck.f2fs: trigger repairing if filesystem was forced to stop
465159f fsck.f2fs: export valid image size
3486b62 mkfs.f2fs: update allocation policy for ro feature
bdd51e5 fsck.f2fs: fix __end_block_addr()
5a5e419 Always use sparse/sparse.h when building for Android
19f77c6 f2fs-tools: fix build error on lz4-1.9.4
986c1f1 Fix format strings in log messages
0d6acbe fsck.f2fs: use elapsed_time in checkpoint for period check
9b7a4c5 mkfs.f2fs: catch total_zones=0 instead of crashing
6148db3 f2fs-tools: use F2FS_BLKSIZE instead of PAGE_*_SIZE
f09c2b7 f2fs_io: support triggering filesystem GC via ioctl
32e7d27 configure.ac: fix cross compilation
65fe94e configure.ac: fix AC_ARG_WITH
6325cf7 Use F2FS_BLKSIZE as the size of struct f2fs_summary_block
c89be7a Use F2FS_BLKSIZE for dev_read_block() buffers
5317d18 Improve compile-time type checking for f2fs_report_zone()
92e2e52 Fix f2fs_report_zone()
648a491 Fix the struct f2fs_dentry_block definition
c964547 resize.f2fs: add option to manually specify new overprovision
a741438 fsck.f2fs: drop compression bit if inline_data is set
406b1c9 f2fs-tools: fix cannot get bdev information
9d0cb9e f2fs_io: add dsync option for write
a7b8b46 tools: fix file too large causing overflow
bddca6f dump.f2fs: add -I nid to dump inode by scan full disk
ebc3879 android_config: add time headers
c1144bf Check fallthrough in mount.h for Mac
bcb9929 avoid unnecessary function
7d902f4 Fix dependencies on linux/blkzoned.h when using Bionic.
274abbb Remove unnecessary config.h
8c97ab3 libzone: remove duplicate header
adcec10 Support zoned device if libc exists
efc2bc7 mkfs.f2fs: fix typo
3034a41 mkfs.f2fs: split unused parameter
dd8d8e5 f2fs-tools: do not use SG_IO in Android
4f216e6 f2fs-tools: move android_config before defining them
48c5dbb f2fscrypt: adjust config file first
4b55459 android_config: add missing uuid library
Signed-off-by: Nick Hainke <vincent@systemli.org>
Replace the fall through comment with fallthrough; in the ar2315 flash
driver.
This fixes a compile warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of defining an own virt_to_phys() use the version from the
generic MIPS arch code which does the same.
This fixes a compile warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
