Use realtek,extif property instead of realtek,extif0 and realtek,extif1
by extending it with the cpu_port parameter.
The extif number is automatically calculated based on cpu_port.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit f444dea428.
It seems that some devices using GPIO WDT have really short WDT timeouts
and when using module_platform_driver registration it happens too late
and thus WDT will timeout and reset the board.
So, for now lets return the postcore_initcall hack for now.
Fixes: f444dea428 ("ath79: remove GPIO driver earlier registration hack")
Signed-off-by: Joan Moreau <jom@grosjo.net>
Link: https://github.com/openwrt/openwrt/pull/16035
Signed-off-by: Robert Marko <robimarko@gmail.com>
NEC Aterm WG600HP is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Hynix H5PS5162GFR-S6C)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EMI-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Atheros AR9382
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 10x/4x
- note : all LEDs are controlled by ath9k chip (AR9382)
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 16 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WG600HP with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WG600HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9382) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : A4:12:42:xx:xx:A0 (config, 0x6 (hex))
WAN : A4:12:42:xx:xx:A1 (config, 0xc (hex))
2.4 GHz: A4:12:42:xx:xx:A2 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : A4:12:42:xx:xx:A3 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NEC Aterm WR9500N is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 2T2R, Atheros AR9344 (SoC)
- 5 GHz : 3T3R, Atheros AR9380
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 12x/4x
- note : all LEDs are controlled by ath9k chip (AR9380)
- UART : pad on PCB (near shielded ath9k chip, white circle)
- assignment : 3.3V, GND, TX, RX from AR8327 side
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WR9500N with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WR9500N and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9380) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : 1C:B1:7F:xx:xx:60 (config, 0x6 (hex))
WAN : 1C:B1:7F:xx:xx:61 (config, 0xc (hex))
2.4 GHz: 1C:B1:7F:xx:xx:62 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : 1C:B1:7F:xx:xx:63 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NEC Aterm WR8750N is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.
Specification:
- SoC : Atheros AR9344
- RAM : DDR2 128 MiB (2x Hynix H5PS5162GFR-S6C)
- Flash : SPI-NOR 8 MiB (Macronix MX25L6406EMI-12G)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Atheros AR9344 (SoC)
- 5 GHz : Atheros AR9382
- Ethernet : 5x 10/100/1000 Mbps
- switch : Atheros AR8327
- LEDs/Keys (GPIO): 10x/4x
- note : all LEDs are controlled by ath9k chip (AR9382)
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- hub (internal): NEC uPD720114
- Power : 12 VDC, 1.5 A (Max. 16 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image (StockFW WebUI):
1. Boot WR8750N with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
7. Perform sysupgrade with a sysupgrade.bin image
sysupgrade <sysupgrade image>
8. Wait ~120 seconds to complete flashing
Flash instruction using initramfs-factory.bin image (bootloader CLI):
1. Connect and open serial console
2. Power on WR8750N and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the GPIO controller on the ath9k chip
(AR9382) and controlled by it. Those LEDs are probed after probing of
ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
booting.
- A reset pin of the internal USB hub is connected to the GPIO
controller of the ath9k chip, like LEDs above. That hub will be
detected after probing of the ath9k chip.
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
MAC Addresses:
LAN : 1C:B1:7F:xx:xx:00 (config, 0x6 (hex))
WAN : 1C:B1:7F:xx:xx:01 (config, 0xc (hex))
2.4 GHz: 1C:B1:7F:xx:xx:02 (config, 0x0 (hex) / art, 0x1002 (hex))
5 GHz : 1C:B1:7F:xx:xx:03 (config, 0x12 (hex) / art, 0x5002 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix PCIe initialization on AR934x by clearing PLL_PWD bit in addition to
PPL(PLL?)_RESET bit of AR724x.
Refresh patches by `make target/linux/refresh`.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In make menuconfig the name is [Amplifi Router HD], and
is missing Ubiquiti. Lets fix that by adding
DEVICE_VENDOR := Ubiquiti to generic-ubnt.mk so the name is:
[Ubiquiti Amplifi Router HD].
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15932
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Huawei AP6010DN is a dual-band, dual-radio 802.11a/b/g/n 2x2 MIMO
enterprise access point with one Gigabit Ethernet port and PoE
support.
Hardware highlights:
- CPU: AR9344 SoC at 480MHz
- RAM: 128MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: AR9344-internal radio
- Wi-Fi 5GHz: AR9580 PCIe WLAN SoC
- Ethernet: 10/100/1000 Mbps Ethernet through Atheros AR8035 PHY
- PoE: yes
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: CAT706SVI (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- radio0 (Wi-Fi 2.4GHz) = label MAC + 1
- radio1 (Wi-Fi 5GHz) = label MAC + 2
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script "run ramboot".
Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile openwrt-ath79-generic-huawei_ap6010dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap6010dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP6X10XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap6010dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues:
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the AHB_CLK/2 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/15941
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Silence ath79 GPIO driver warning by setting GPIO numberspace base
dynamically. This patch also reorganize and fix the GPIO numbers on
6.6 kernel. The new gpio chip base number algorithm:
gpiochip ath79-SOC ath9k-0 ath9k-1
base 512 512+ngpios 512+ngpios+10
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/15784
Signed-off-by: Robert Marko <robimarko@gmail.com>
Each ath9k device only has 10 gpios. ath9k-0 gpio number range is
502-511, and ath9k-1 gpio number range is 492-501. So "5GHz External
Antenna A" gpio line number should be 492 instead of 489.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/15784
Signed-off-by: Robert Marko <robimarko@gmail.com>
This hack is used to make sure that the mfd device starts before the
mtd driver[1]. Now the linux driver framework "struct spi_driver {}"
can always ensure this.
[1] 47f8fd1dde ("ar71xx: rewrite SPI drivers for the RB4xx boards")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
After porting the ar71xx target to the new ath79 target, we are now
using the device tree instead of the device mach file. And the
platform drivers already support deferred probe. So there is no need
to keep it.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Currently, information from MikroTik hard_config is only available via
sysfs, meaning that we have to rely on userspace to for example setup MACs.
So, lets provide a basic NVMEM layout based driver to expose the same cells
as sysfs driver exposes.
Do note that the we dont extract the WLAN caldata and BDF-s at this point.
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/15665
Signed-off-by: Robert Marko <robimarko@gmail.com>
This driver has already been packed as a software package. There is
no need to build it into the kernel.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Currently, of_get_ethdev_address() return is checked for any return error
code which means that trying to get the MAC from NVMEM cells that is backed
by MTD will fail if it was not probed before ag71xx.
So, lets check the return error code for EPROBE_DEFER and defer the ag71xx
probe in that case until the underlying NVMEM device is live.
Link: https://github.com/openwrt/openwrt/pull/15752
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, trying to upgrade on a MikroTik NAND device will force you to
use sysupgrade -n due to:
upgrade: The device is supported, but the config is incompatible to the new image (1.0->1.1). Please upgrade without keeping config (sysupgrade -n).
upgrade: NAND images switched to yafut. If running older image, reinstall from initramfs.
So instead of having users manually set the new compat version lets do
what other targets do and set it for all NAND devices after good boot.
Link: https://github.com/openwrt/openwrt/pull/15754
Signed-off-by: Robert Marko <robimarko@gmail.com>
gpio is deprecated. Found with dtc's -Wdeprecated_gpio_property
Used git grep -E $'\tgpio = <' to make the changes.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15681
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
We haven't received any bug reports in the past few weeks. So it's
time to set kernel 6.6 as the default and remove kernel 6.1 support.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
0db4f9785c changed the variable name from
athaddr to ethaddr. Restore.
Fixes: 0db4f9785c ("ath79: convert ath10k calibration data to NVMEM (ASCII MAC)")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Before the nvmem rework, this was already handled in dts with
mtd-cal-data instead of qca,no-eeprom. No need to duplicate. Also, the
800 size value seems nonsensical. 440 is the standard.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Userspace handling is deprecated.
Also fix a bug with userspace handling where the wrong calibration data
was being used for the PCI card. The dts was correct but userspace was
not.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The Yafut tool now has limited capabilities for working on filesystem
images stored in regular files. This enables preparing Yaffs2 images
for devices with NOR flash using upstream Yaffs2 filesystem code instead
of the custom kernel2minor tool.
Since minimizing the size of the resulting filesystem image size is
important and upstream Yaffs2 code requires two allocator reserve blocks
to be available when writing a file to the filesystem, a trick is
employed while preparing an OpenWRT image: the blank filesystem image
that Yafut operates on initially contains two extra erase blocks that
are chopped off after the kernel file is written. This is safe to do
because Yaffs2 has a true log structure and therefore only ever writes
sequentially (and the size of the kernel file is known beforehand).
While the two extra erase blocks are necessary for writes, Yaffs2 code
seems to be perfectly capable of reading back files from a "truncated"
filesystem that does not contain these extra erase blocks.
In terms of image size, this new approach is only marginally worse than
the current kernel2minor-based one: specifically, upstream Yaffs2 code
needs to write three object headers (each of which takes up an entire
data chunk) when the kernel file is written to the filesystem:
- an object header for the kernel file when it is created,
- an object header for the root directory when the kernel file is
created,
- an updated object header for the kernel file when the latter is
fully written (so that its new size can be recorded).
kernel2minor only writes two of these headers, which is the absolute
minimum required for reading the file back. This means that the
Yafut-based approach causes firmware images to be at most one erase
block (64 kB) larger than those created using kernel2minor, but only in
the very unfortunate scenario where the size of the kernel file is
really close to a multiple of the erase block size.
The rest of the calculations performed when the empty filesystem image
is first prepared stems from the Yaffs2 layout used by MikroTik NOR
devices: each 65,536-byte erase block contains 63 chunks, each of which
consists of 1024 bytes of data followed by 16-byte Yaffs tags without
ECC data; each such group of 63 chunks is then followed by 16 bytes of
padding, which translates to "-C 1040 -B 64k -E" in the Yafut
invocation. Yaffs2 checkpoints and summaries are disabled (using
Yafut's -P and -S switches, respectively) as they are merely performance
optimizations that require extra storage space. The -L and -M switches
are used to force little-endian or big-endian byte order (respectively)
in the resulting filesystem image, no matter what byte order the build
host uses. The tr invocation is used to ensure that the filesystem
image is initialized with 0xFF bytes (which are an indicator of unused
space for Yaffs2 code).
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Link: https://github.com/openwrt/openwrt/pull/13453
Signed-off-by: Robert Marko <robimarko@gmail.com>
Dell/SonicWall APL26-0AE (marketed as SonicPoint ACe) is a dual band
wireless access point. End of life as of 2022-07-31.
Specification
SoC: QualcommAtheros QCA9550
RAM: 256 MB DDR2
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9890 oversized Mini PCIe card
Ethernet: 2x 10/100/1000 Mbps QCA8334
port labeled lan1 is PoE capable (802.3at)
USB: 1x 2.0
LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color
Buttons: 2x GPIO controlled
Serial: RJ-45 port, SonicWall pinout
baud: 115200, parity: none, flow control: none
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
All described procedures were done in following environment:
ROM Version: SonicROM (U-Boot) 8.0.0.0-11o
SafeMode Firmware Version: SonicOS 8.0.0.0-14o
Firmware Version: SonicOS 9.0.1.0
In case of other versions, following installation instructions might be
ineffective.
Installation
1. Prepare TFTP server with OpenWrt sysupgrade image and rename that
image to "sp_fw.bin".
2. Connect to one of LAN ports.
3. Connect to serial port.
4. Hold the reset button (small through hole on side of the unit),
power on the device and when prompted to stop autoboot, hit any key.
The held button can now be released.
5. Alter U-Boot environment with following commands:
setenv bootcmd bootm 0x9F110000
saveenv
6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip"
(TFTP server, default is 192.168.1.10) addresses in U-Boot
environment, then run following commands:
tftp 0x80060000 sp_fw.bin
erase 0x9F110000 +0x1EF0000
cp.b 0x80060000 0x9F110000 $filesize
7. After successful flashing, execute:
boot
8. The access point will boot to OpenWrt. Wait few minutes, until the
wrench LED will stop blinking, then it's ready for configuration.
Known issues
Initramfs image can't be bigger than specified kernel size, otherwise
bootloader will throw LZMA decompressing error. Switching to lzma-loader
should workaround that.
This device has Winbond 25Q256FVFG and doesn't have reliable reset, which
causes hang on reboot, thus broken-flash-reset needs to be added. This
property addition causes dispaly of "scary" warning on each boot, take
this warnig into consideration.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Hardware:
SoC: Qualcomm Atheros QCA956X ver 1 rev 0
CPU clock: 775.000 MHz
Memory: 128 MB DDR2
Flash: 32 MB SPI NOR mx25l25635e
Switch: Atheros AR8327 rev. 4
Ethernet: 5x 10/100/1000 Mbps (1 WAN + 4 LAN)
Buttons: 1x Reset
Serial: TX, RX, GND, VCC
Baudrate: 115200
Wifi: Qualcomm Atheros qca988x 802.11ac/n - 3x3
Qualcomm Atheros AR9561 802.11b/g/n - 3x3
Not working:
Leds: 1x via a SPI controller
Display: ST7789V or ILI9341V
controlled by stm32f205.
Note:
DSA changes are ready, but we have an issue with
ports not working after 20-30 minutes. So for now
we use swconfig.
Installation: serial connection only
There is a J11 four pin connector. You need to connect TX, RX and GND.
You can find very good information about the device here
https://github.com/alexanderhenne/AFi-R?tab=readme-ov-file#finding-j11
Upgrading via serial port:
1. Download the kernel initramfs image. Copy the image to a TFTP server
2. Connect to console on the AP, and connect the LAN1 port to your PC LAN
3. Stop autoboot to get to U-boot shell
Interrupt the autoboot process by pressing any key when prompted
4. Transfer the kernel image with TFTP
Set your ip address on your TFTP server to 192.168.1.254
# tftpboot 0x81000000 amplifi-router-hd-initramfs-kernel.bin
5. Load the image
# bootm 0x81000000
6. SCP sysupgrade image from your PC to the Amplifi HD
(If you use a newer mac use scp -O)
# scp openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Write sysupgrade to the firmware partition
# mtd write /tmp/openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin firmware
8. Reboot your device
# reboot
Credit to alexanderhenne for all the information.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Carambola3 is a WiFi module based on Qualcomm/Atheros QCA4531
http://wiki.8devices.com/carambola3
Specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- 1x USB 2.0 Host socket
- UART for serial console
- 12x GPIO
Flash instructions:
Upgrading from ar71xx target:
- Upload image into the board:
scp openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin \
root@192.168.1.1/tmp/
- Run sysupgrade
sysupgrade -F /tmp/openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin
Upgrading from u-boot:
- Set up tftp server with openwrt-ath79-generic-8dev_carambola3-initramfs-kernel.bin
- Go to u-boot (reboot and press ESC when prompted)
- Set TFTP server IP
setenv serverip 192.168.1.254
- Set device ip from the same subnet
setenv ipaddr 192.168.1.1
- Copy new firmware to board
tftpboot 0x82000000 initramfs.bin
- Boot OpenWRT
bootm 0x82000000
- Upload image openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin into the board
- Run sysupgrade.
Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/15514
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is no need to use 'list_for_each_entry_safe' here, as nothing is
removed from the list in the 'for' loop.
Use 'list_for_each_entry' instead, it is slightly less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://github.com/openwrt/openwrt/pull/15435
Link: https://github.com/openwrt/openwrt/pull/15435
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
FCC ID: A8J-EWS660AP
Engenius ENS1750 is an outdoor wireless access point with
2 gigabit ethernet ports, dual-band wireless,
internal antenna plates, and 802.3at PoE+
Engenius EWS660AP, ENS1750, and ENS1200 are "electrically identical,
different model names are for marketing purpose" according to docs
provided by Engenius to the FCC.
**Specification:**
- QCA9558 SOC 2.4 GHz, 3x3
- QCA9880 WLAN mini PCIe card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- AR8033 PHY SGMII GbE with PoE+ OUT
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM
- UART at J1 populated, RX grounded
- 6 internal antenna plates (5 dbi, omni-directional)
- 5 LEDs, 1 button (power, eth0, eth1, 2G, 5G) (reset)
**MAC addresses:**
Base MAC addressed labeled as "MAC"
Only one Vendor MAC address in flash
eth0 *:d4 MAC art 0x0
eth1 *:d5 --- art 0x0 +1
phy1 *:d6 --- art 0x0 +2
phy0 *:d7 --- art 0x0 +3
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
**Format of OEM firmware image:**
The OEM software of ENS1750 is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-ar71xx-generic-ens1750-uImage-lzma.bin
openwrt-ar71xx-generic-ens1750-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Tested-by: Kevin Abraham <kevin@westhousefarm.com>
Signed-off-by: Kevin Abraham <kevin@westhousefarm.com>
