Commit Graph

1044 Commits

Author SHA1 Message Date
Felix Fietkau
22c0206044 lantiq: add image build template for NAND devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau
8058e4778b lantiq: simplify image building code
Specifying the device profile in PROFILES is unnecessary, and for all
devices the DEVICE_PROFILE variable matched the device name.
Get rid of this useless variable and set DEVICE_DTS to $(1)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau
cc88df1a38 lantiq: fix building NAND images in default config
Remove remaining references to $(PROFILE)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau
ceee47ba64 lantiq: disable jffs2 support on xrx200
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau
8e2764ce9b image.mk: clean up redundant code related to DEVICE_DTS
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-15 14:14:11 +02:00
Ben Mulvihill
1cc092f72b lantiq: mac address setting on BTHOMEHUBV3A
Rename uboot environment partition on BT Home Hub 3A so that mac address
setting works correctly.

Also, the mac address field in the ath9k calibration data is not used,
and should not be referenced in the dts.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
2016-07-05 22:59:14 +02:00
Felix Fietkau
2270fc5947 Revert "lantiq: enable SMP for XRX200"
This reverts commit cc3bfdb62f.

Apparently the ethernet driver is not SMP safe, as reported in
https://bugs.lede-project.org/index.php?do=details&task_id=27

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-27 13:06:56 +02:00
Hauke Mehrtens
bf32177a1d kernel: remove full cache flush in fuse_copy_do() for MIPS
This patch was introduced in commit r16412 for the brcm47xx target only
and then moved to generic in commit r32395. It was initially added
because of ticket #5186 and should fix some problems with fuse file
systems and MIPS caches. The commit comment in r32395 says that this a
generic problem in MIPS CPUs, but does not name any specifics about
that. There was a fix added to kernel 2.6.21 in commit commit
7575a49f20 "[MIPS] Implement flush_anon_page()." that should fix this
problem, but that was already available before both commits were done
to OpenWrt.

I just tested fuse with ntfs.3g without this patch on a BCM4704
(BMIPS3300 V0.6) SoC and haven't seen any problems. Someone reported
that removing this patch improves some fuse operations by 5 times on
some modern MIPS cores.
My test was only a simple "dd if=/dev/zero of=/mnt/zero bs=5000" to an
USB stick.

This patch removes the patch to OpenWrt, because I assume that it is
not needed any more and Felix, the orginal author, also thinks so.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-26 18:22:23 +02:00
Hauke Mehrtens
84d489f64f kernel: update to version 4.4.14
Changelog: https://cdn.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.4.14

Some manual changes to target/linux/generic/patches-4.4/610-
netfilter_match_bypass_default_checks.patch were needed.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-26 18:20:37 +02:00
Mathias Kresin
f080cfab72 lantiq: fix network in failsafe
So far the network in failsafe is setup only for one board. Use the
eth0 interface as lan interface for all boards for now.

If a board has its lan interface(s) on another eth, a special
handling based on the board name can be added.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-06-22 19:32:06 +02:00
Oswald Buddenhagen
9759fde40a lantiq: add support for ARV7506PW11 (Alice/O2 IAD 4421)
Ethernet, ADSL2+ and LEDs are fully functional.

Supporting the two TAE ports and SIP gateway was not attempted.

The WiFi is unreliable, due to experimental support for rt35xx family
devices by the rt2800pci driver.

Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
[rebase to LEDE HEAD]
[switch to normal image instead of brnboot image]
[remove not required pinmux child nodes keys, leds, ebu, exin, pci_in and pci_out]
[remove switch_rst pinmux child node (no support for hw reset in driver/setting a default GPIO value in DT]
[enable usage of the wireless LED]
[fixup mac address configuration]
Sgned-off-by: Mathias Kresin <dev@kresin.me>
2016-06-22 19:32:06 +02:00
Ben Whitten
b7baaaf782 kernel: Move append-dtb to common image-commands
This build step is used by various targets, move it to a common section.

Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
2016-06-22 19:32:06 +02:00
Daniel Gimpelevich
34fdfbf328 lantiq: Slow down SPI flash on the DGN3500
The bootloader uses 30 MHz as the SPI frequency for flash on the Germany and
North America models, and 50 MHz for it on the worldwide model, but the Lantiq
SPI driver in OpenWrt and LEDE may access the flash differently such that
writes are capped at 20 MHz, leading to read errors reported on the worldwide
model at 30 MHz.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Acked-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2016-06-22 19:32:06 +02:00
John Crispin
f054e82bdc lantiq: remove gr7000 support
this seems to have never worked as the wrong SoC is selected

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-22 19:32:06 +02:00
Hauke Mehrtens
84b3d92180 lantiq: make EASY80920 work with both chip versions
The EASY80920 is available with the A1X and the A2X chip version
depending on the board version. Add both firmware versions to device
tree and make the driver load the correct version depending on the chip
version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-21 21:58:59 +02:00
Hauke Mehrtens
7f5b8cc376 lantiq: use new partition layout for EASY80920NAND
This matches the EASY80920NAND boards with UGW.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-21 21:58:59 +02:00
Hauke Mehrtens
8bfa230e9f lantiq: build fullimage.img for EASY80920NAND
This image format is used by Lantiq's / Intel's UGW version 6.1 to 7.1.
These images can be flashed onto a board with the SoC vendor boot
loader as a replacement for the vendor firmware.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-21 21:58:59 +02:00
Hauke Mehrtens
ecdfbeae85 lantiq: remove patch adding support for building without reset controller
The lantiq kernel arch code selects CONFIG_RESET_CONTROLLER always, so
it is always selected when the lantiq target is build. we do not need
support for unselected CONFIG_RESET_CONTROLLER option.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-06-21 21:58:59 +02:00
Ben Mulvihill
7df43d88ec lantiq: fix typo in new image generation
Fix typo in commit a6f7536a73
(new image generation)

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
2016-06-21 13:49:54 +02:00
Mathias Kresin
153b3f05d4 lantiq: BTHOMEHUBV5A - use the power event code for the restart button
The restart event code is used in LEDE to trigger a factory reset on
long press as well.

By using the power event code, the restart functionality can be used
without being prone to trigger a factory reset.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-06-20 11:45:44 +02:00
Mathias Kresin
551c9c8300 lantiq: diag - switch off the power led on failsafe
This patch is a follow up to commit 4cf3fd4 "add support for indicating
the boot state using three leds".

At the time of writing the patch, I wasn't aware that it's possible to
switch info failsafe after boot (factory reset).

Enabling the failsafe led without disabling the running led causes an
unexpected led colour on devices using a single multicolour led to
indicate the boot state.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-06-20 11:45:44 +02:00
Mathias Kresin
32012decc3 lantiq: fix build of NAND sysupgrade images
The *_UBIFS_OPTS variables need to be prefixed with DEVICE_ to match
the profile name.

The conditions need to be evaluated after the *_UBIFS_OPTS are set,
otherwise the variables are always empty.

Do not append or pass the DEVICE_ prefixed profile name to the images.
Use the name that is passed by the Image/Build/Profile/ step.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-06-20 11:45:44 +02:00
Felix Fietkau
982108f7e5 lantiq: clean up / fix LegacyDevice template handling
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-17 20:23:11 +02:00
Felix Fietkau
f4c59a204e lantiq: get rid of ifneq() checks inside command templates
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-17 20:23:11 +02:00
John Crispin
9a0381f969 lantiq: small fix for legacy profile builds
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-17 20:11:24 +02:00
John Crispin
a6f7536a73 lantiq: convert remaining legacy targets to the new image generation code
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-17 04:13:07 +02:00
Felix Fietkau
a285f1895b Revert "lantiq: Use correct macaddr generating logic for the DGN3500"
This reverts commit 492964e741, which
makes no sense. /etc/board.d cannot be used for system init stuff.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-15 18:40:48 +02:00
Felix Fietkau
3a75777e86 lantiq: refresh patches
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-15 14:36:47 +02:00
John Crispin
9233db23f3 lantiq: the io space was still not big enough for UHCI
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 08:34:05 +02:00
John Crispin
88019c6c77 lantiq: add ARV4525PW wifi led
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 06:43:02 +02:00
John Crispin
90c48dd49d lantiq: fix VG3503J loader generation
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 06:43:02 +02:00
John Crispin
d5666b98fa lantiq: fix fritz7320 wifi support
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 06:43:02 +02:00
John Crispin
98d00c35e3 lantiq: fix io_space_limit
this broke uhci pci support on some arv units

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-14 06:43:02 +02:00
John Crispin
d57990e071 lantiq: fix ARV452CQW button gpio setup
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:43 +02:00
John Crispin
d5143a49b7 lantiq: add AVM image mageic to sysupgrade script
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:43 +02:00
John Crispin
239ad94165 lantiq: add xway_legacy target
due to bloat recent builds fail to fit into the flash of the old danube units

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:43 +02:00
John Crispin
2ae06f3013 lantiq: gpio-export fails to build if GPIO_SYSFS is not enabled
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:43 +02:00
John Crispin
bf007a480a lantiq: Add Support for Fritz!Box 7360 SL
Signed-off-by: Sebastian Ortwein <krone@animeland.de>
Tested-by: Guido Lipke <lipkegu@gmail.com>
2016-06-13 22:51:43 +02:00
John Crispin
b50b0cff2d lantiq: use new property name for eiu irqs
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:41 +02:00
John Crispin
d61af50cf3 lantiq: fix a regression in the eiu irq loading code
this worked in 3.18 but broke at some point. the old code that loaded a
irq table was incorrewct anyhow as it mapped the irqs int he domain which
should really be done when the driver using them loads them and not the
irq driver itself.

Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:41 +02:00
John Crispin
027da34957 lantiq: add default lan setup to board.d script
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-13 22:51:41 +02:00
Felix Fietkau
c536da365b lantiq: add VLAN handling fixes to xrx200 ethernet driver
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-13 17:58:07 +02:00
Felix Fietkau
172eebbd28 lantiq: fold 0400-xrx200-net-multi-phy.patch into 0025-NET-MIPS-lantiq-adds-xrx200-net.patch
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-13 17:58:07 +02:00
Felix Fietkau
1da87516e5 lantiq: change xrx200 ethernet driver WRED signal to global to fix spurious packet loss issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-12 14:53:18 +02:00
Felix Fietkau
69c99a423a lantiq: enable swconfig LED support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-11 09:49:13 +02:00
Felix Fietkau
cc3bfdb62f lantiq: enable SMP for XRX200
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-11 09:49:13 +02:00
Felix Fietkau
2d48f93ff4 lantiq: add Buffalo WBMR-300HPD support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-11 09:49:13 +02:00
Felix Fietkau
cc87d144e1 lantiq: refresh xrx200 kernel config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-11 09:49:13 +02:00
Felix Fietkau
2cf67832ec lantiq: remove dummy ltq_machine_power_off to fix gpio-poweroff drivers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-11 09:49:13 +02:00
Felix Fietkau
97e3d10df9 lantiq: fix image DEVICE_DTS handling, add proper default value
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-07 09:42:11 +02:00
Felix Fietkau
821ccd2b36 lantiq: only call Image/Prepare/Profile for defined profiles
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-07 09:35:18 +02:00
John Crispin
ba42c1db41 lantiq: un-macro the image building code
Signed-off-by: John Crispin <john@phrozen.org>
2016-06-05 23:23:57 +02:00
Alexander Couzens
1616bb2a7d lantiq/image: move tplink specific image into own file
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-06-05 23:23:57 +02:00
Alexander Couzens
aa930ba3dd lantiq: unmacro tp-link boards
even it's a little bit verbose, unmacrod board descriptions are much
easier to read and to understand.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-06-05 23:23:57 +02:00
Daniel Gimpelevich
2b4e5d478b kernel: remove a hack that was obsoleted upstream
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2016-05-27 16:08:47 +02:00
Daniel Gimpelevich
492964e741 lantiq: Use correct macaddr generating logic for the DGN3500
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2016-05-27 16:08:47 +02:00
Daniel Gimpelevich
8b321d45be lantiq: Fix macaddr-setting code on DGN3500 and possibly other devices
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2016-05-27 16:08:47 +02:00
Daniel Gimpelevich
e8780b643b lantiq: Use the correct SPI flash speed for the Netgear DGN3500
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2016-05-27 16:08:47 +02:00
Mathias Kresin
b2b917cd06 lantiq: do not build images which exceed the flash size
The user benpicco in #openwrt reported that images are build which are
bigger that the available flash size.

He provided a proof of concept fix and gave permission to me to send it
for inclusion.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:17 +02:00
Mathias Kresin
db66b157db lantiq: VGV7510KW22 - enable the IP101A phy
The RJ45 WAN port is used for xDSL as well as the IP101A.

The pins 1,2,3,6 of the RJ45 are connected to the IP101A and the
pins 4,5 are connected to the xdsl chip.

Drop the ip101a-rst node. It can't be controlled and is not required
at all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:17 +02:00
Mathias Kresin
4d5db712e3 lantiq: VGV7510KW22 - fix pinmux configuration
The STP pinmux was initially added in assumption LAN2 led is driven by
it. It worked somehow because STP group and gphy0 led0 share the GPIO.
Do it the right way by adding the gphy0 led0 the gphy function.

According to the author, the SPI node is a copy & paste leftover. Which
makes sense since nothing is connected to the SPI bus on this device.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:17 +02:00
Mathias Kresin
a9f7586ad2 lantiq: VGV7519 - fix brn partition layout
Use the brnboot partition layout as it is listed in the OpenWrt wiki
article for this board.

Configure the brnboot root selector for this device as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:17 +02:00
Mathias Kresin
28faa3f292 lantiq: VGV7519 - get mac address from board_config partition
Use the mac address stored in the board_config partition instead of a
static one.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:17 +02:00
Mathias Kresin
1e395608cc lantiq: VGV7519 - add vlan support
Add the lantiq,switch property to enable vlans and setup them up.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:16 +02:00
Mathias Kresin
1deab53d88 lantiq: VGV7519 - add second usb port
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:16 +02:00
Mathias Kresin
79d92bb7ac lantiq: VGV7519 - cleanup pinmux configuration
Cleanup the pinmux configuration by removing the unused spi node. Nothing is connected to the SPI bus on devices.

The stp_out pinmux child node covers the same GPIOs as the already used
stp group.

The same applies to the gphy-leds_out pinmux node and the "gphy0
led1" as well as "gphy1 led0" groups.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:16 +02:00
Mathias Kresin
8a382f1221 lantiq: VGV7519 - remove/merge redundant parts in dts
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:16 +02:00
Mohammed Berdai
f778cdd9c9 lantiq: fix ARV4518PWR01 network
This patch fixes the missing Lan interface config in the file
/etc/config/network for ARV4518PWR01/A which results in eth0 and br-lan
being down and therefore no way to access the router unless via UART-TTL.

Signed-off-by: Mohammed Berdai <mohammed.berdai@gmail.com>
2016-05-27 15:50:16 +02:00
John Crispin
a42e84b2db lantiq: fix regression in VG3503J.dts
9d0608eef3 - "lantiq: VG3503J - merge profiles"

resulted in the dts file missing the version string.

Signed-off-by: John Crispin <john@phrozen.org>
2016-05-24 17:17:36 +02:00
Mathias Kresin
abfdddfb3c lantiq: VG3503J - use the 11G firmware
Use the 11G firmware for the phys as the oem firmware does.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-23 11:03:25 +02:00
Mathias Kresin
9d0608eef3 lantiq: VG3503J - merge profiles
The only difference between the VG3503J profiles is the version of the
gphy firmware that gets loaded. This can be handled perfect fine in one
device tree source file.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-23 11:03:24 +02:00
Mathias Kresin
21bdd79b33 lantiq: disable phy led complex (test) functions by default
They can be added using the phy led device tree bindings if required.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-23 11:03:23 +02:00
Felix Fietkau
311faaa1bd lantiq: move ubi/ubifs options to the image makefile
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-19 15:13:29 +02:00
John Crispin
b8ab6af1a9 global: change my email address
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-12 03:29:36 +02:00
Álvaro Fernández Rojas
b062266ad6 kernel: update kernel 4.4 to version 4.4.9
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-10 10:43:17 +02:00
blogic
d4de9f72f3 lantiq: VGV7510KW22BRN - set the phy clock source
VGV7510KW2 with VRX288 v1.2 has brnboot 1.8 installed. Starting with
this brnboot version, the "GPHY Clock Source" isn't set anymore by
brnboot, with the result that xrx200-net fails to probe/initialize the
phys.

Use the phy clock source device tree binding to specify the clock source.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49284
2016-05-10 10:43:12 +02:00
blogic
44cace4dab lantiq: add device tree binding for the phy clock source
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49283
2016-05-10 10:43:12 +02:00
blogic
60ac485274 lantiq: VGV7510KW22BRN - support dual-image
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49282
2016-05-10 10:43:12 +02:00
blogic
d7438ce315 lantiq: handle the dual-firmware layout of brnboot
brnboot based devices can have two Image partitions. When flashing
images via the brnboot recovery web interface, the Image partitions are
written alternating.

The current active Image partition is stored in the first byte of the
Primary_Setting partition by using 0x00 for Code_Image_0 and 0x01 for
Code_Image_1.

By using the information about the active "Code Image", it is possible
to ensure that the rootfs belongs to the current booted Image/Kernel.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49281
2016-05-10 10:43:12 +02:00
blogic
b7fc892eb5 lantiq: move partitions into partion table node
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49280
2016-05-10 10:43:12 +02:00
blogic
b695ce2999 lantiq: use sysupgrade.bin postfix for tplink images
Use the same name for TP-Link images as it was with the old image build
code.

Move the BOARD_ID export to the TP-Link image build recipe, to indicate
that the variable is only related in this context.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49279
2016-05-10 10:43:12 +02:00
blogic
5ed2140162 lantiq: VG3503J - use the same PHY led functionality as the OEM firmware
Based on the vg3503j_gphy_led.sh script published in the VG3503J wiki
article, the OEM Firmware uses the following PHY led functionality:

    gphy led 0: LINK/ACTIVITY
    gphy led 1: LINK
    gphy led 2: ACTIVITY

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49278
2016-05-10 10:43:12 +02:00
blogic
b529387d8c lantiq: use the same functionality for all ethernet phys led
The VGV7510KW22 has the leds for LAN1-3 connected to pin1 of the phys
and the led for LAN4 connect to pin0 of the phy. This results with the
current configuration in a fast flashing LAN4 led as soon as a network
cable is connected. Something similar was reported on the forum[1] for
the VGV7519 as well.

Since it isn't predicable to which pin a (single) phy led is connected,
use the (default) pin1 functionality

    Constant On: 10/100/1000MBit
    Blink Fast: None
    Blink Slow: None
    Pulse: TX/RX

for all ethernet phy leds.

After checking pictures of all vr9 boards, it looks like only the VG3503J
has more than one led connected per phy. Using the phy led device tree
bindings to assign the functionality to the "additional" leds, the
VG3503J phy leds should behave as before.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

[1] https://forum.openwrt.org/viewtopic.php?pid=321523

SVN-Revision: 49270
2016-05-10 10:43:12 +02:00
blogic
6249269322 lantiq: fix minor typos in 11G/22F phy driver
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49269
2016-05-10 10:43:12 +02:00
Jo-Philipp Wich
eb529d2625 lantiq: fix xway image building
Commit 8c130dd (lantiq: use new image build process for some images) broke
image generation for the xway target since the generated macros reference not
existing WBMRA.dts and WBMRB.dts files leading to the following build error:

  mips-openwrt-linux-musl-cpp: error: ../dts/WBMRA.dts: No such file or directory
  mips-openwrt-linux-musl-cpp: warning: '-x assembler-with-cpp' after last input file has no effect
  mips-openwrt-linux-musl-cpp: fatal error: no input files

Previously both the WBMRA and WBMRB profiles shared a common WBMR DT since
the only difference is the embedded firmware kmod package.

Extend the lantiqImage macro to optionally support specifying a different
DTS file and use this facility to let the both WBMR profiles reference the
correct device tree file.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-04-27 01:22:32 +02:00
Álvaro Fernández Rojas
3faf65e928 kernel: update kernel 4.4 to version 4.4.8
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-04-24 11:32:17 +02:00
John Crispin
dc92917409 image / basefiles: make console password configurable
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
Signed-off-by: John Crispin <john@phrozen.org>
2016-04-18 21:53:07 +02:00
John Crispin
27c10641a0 lantiq: use dwc2 by default on all ar9 boards
The dwc2 USB driver now works on Lantiq ar9, but the
default is still ltq-hcd-ar9. This patch switches to
dwc2 by default.

v2: all ar9 boards (v1 was just for BTHOMEHUBV3A and WBMR)

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 49254
2016-04-26 11:44:17 +00:00
John Crispin
fa1927839e lantiq: install uboot-envtools by default on BTHOMEHUBV3A
The only way to access the u-boot console on the BTHOMEHUBV3A
is by soldering a serial console onto some really tiny pads.

To enable installation without soldering it would be helpful
to be able to modify the uboot environment from within
the ramdisk image used as part of the installation process.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 49253
2016-04-26 11:44:13 +00:00
John Crispin
544efb9ad1 lantiq: remove read-only flag on two partitions on BTHOMEHUBV3A
Remove read-only flag on two partitions on BTHOMEHUBV3A:
  uboot-config - otherwise fw_setenv command cannot be used.
  ath9k-cal    - so that ath9k calibration data can be copied
                 to the partition on a newly installed board.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 49250
2016-04-26 11:44:03 +00:00
John Crispin
0a4f2b5920 lantiq: Fix typo in LED diag script.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Acked-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49242
2016-04-26 11:43:31 +00:00
John Crispin
517a6fab5f lantiq: use new image build process for brnImages
LZMA compress the kernel without dictionary, otherwise brnboot fails to
uncompress the kernel.

The filesystem parameter of mkbrncmdline was dropped since the used
filesystem isn't exported in the kernel build step and at least in my
tests everything works without the parameter. If the parameter is
required for some reason, the static keyword "squashfs" can be used.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49241
2016-04-26 11:43:28 +00:00
John Crispin
6ade87df0a lantiq: remove orphaned tp-link image build steps
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49239
2016-04-26 11:43:21 +00:00
John Crispin
2ef2a6aaf6 lantiq: build sysupgrade images for lantiqImage
Tested with VGV7510KW22NOR.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49238
2016-04-26 11:43:18 +00:00
John Crispin
ef66c8d72e lantiq: new image build process - fix kernel entry address
Set the kernel entry address to the same value as it is used for the old
image build build process.

Fixes boot of uImages on VGV7510KW22NOR and others.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 49237
2016-04-26 11:43:15 +00:00
John Crispin
8c130dd3c1 lantiq: use new image build process for some images
This adds for some easy images the new build process.

This was only tested on some TP-Link devices, please test.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 49210
2016-04-21 19:46:53 +00:00
Hauke Mehrtens
f0b3964f1b kernel: update kernel 4.4 to version 4.4.7
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 49176
2016-04-16 21:05:48 +00:00
John Crispin
0039bc665c lantiq-dsl: add missing blank in dsl output
blank inserted before ACTATP

Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>

SVN-Revision: 49137
2016-04-09 10:25:29 +00:00
John Crispin
c701c3ce77 lantiq-dsl: bugfix latency values swapped for lucistat
swapped wrong latency output

Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>

SVN-Revision: 49136
2016-04-09 10:25:24 +00:00
John Crispin
7beb53b1a5 lantiq-dsl: bugfix db negative sign after comma
If db is negative minus sign was shown after comma

Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>

SVN-Revision: 49135
2016-04-09 10:25:20 +00:00
Gabor Juhos
4d0681d865 lantiq: lzma-loader: fix O32 ABI conformance
According to the calling convention of the o32 ABI the
caller function must reserve stack space for $a0-$a3
registers in case the callee needs to save its arguments.

The assembly startup code does not reserve stack space
for these registers thus when the main C function needs
to save its arguments, that will cause a stack overflow.

Fix the assembly code to reserve stack space for the
registers to avoid that.

Compile tested only.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 49061
2016-03-21 13:15:25 +00:00
John Crispin
d6d0597cdf lantiq: use upstream mechanism to append device tree file
Instead of using our patch-dtb program just place the device tree
behind the kernel binary and then let the in kernel mechanism fetch it.
This also adds support for having the device tree file in the boot
loader.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 49050
2016-03-20 14:41:54 +00:00
Felix Fietkau
dc3a7131a9 lantiq: print profile name in dsl lucistat
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 48949
2016-03-07 11:03:44 +00:00
Felix Fietkau
06b630047f lantiq: add dsl firmware to default packages
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 48942
2016-03-07 11:03:21 +00:00
Felix Fietkau
4ac99abeb3 lantiq: do not set default firmware file
We are now shipping a DSL firmware, do not set it by default to some
file name.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 48941
2016-03-07 11:03:18 +00:00
Hauke Mehrtens
cb04b8d582 kernel: update kernel 4.4 to version 4.4.3
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 48783
2016-02-25 21:54:39 +00:00
John Crispin
48f82b53d0 use "-gt" instead of ">" with [ in /lib/functions/lantiq_dsl.sh
Avoids inadvertent file creation when executing
`/etc/init.d/dsl_control status`.

Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>

SVN-Revision: 48700
2016-02-12 08:29:44 +00:00
John Crispin
a0e8833cb5 lantiq: VGV7510KW22/VGV7519 update spi pinmux group
With the backport of the kernel 4.5 pinctrl-xway patches (3551609d &
826bca29) the pinmux group "spi" was splitted into "spi_di", "spi_do" &
"spi_clk". But the no longer existing group "spi" is still used by some
device tree source files.

This fixes the detection of the wireless chipset of the VGV7510KW22.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48658
2016-02-08 08:25:31 +00:00
John Crispin
7c0009a52e lantiq: BTHOMEHUBV5A - explicit select the flash device
The stock u-boot doesn't disable unused flash banks. Therefore, the nand
driver tries to initialize a not connected NOR flash and the device
hangs on boot.

Workaround the issue by selecting the second flash bank (NAND).

Signed-off-by: Mathias Kresin <openwrt@kresin.me>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48657
2016-02-08 08:25:22 +00:00
John Crispin
c3fc71527d lantiq: fix wrong parameter order in xway_nand driver
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48656
2016-02-08 08:25:15 +00:00
Felix Fietkau
6fd5449198 lantiq: Make the ar9.dtsi sram node match "simple-bus"
All other SoC types are using "lantiq,sram" and "simple-bus" to ensure
that all child nodes are set up correctly during linux kernel
initialization (plat_of_setup(void) in arch/mips/lantiq/prom.c). Without
this some of sram child nodes might not be parsed.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48548
2016-01-29 00:42:50 +00:00
Felix Fietkau
022855baf2 lantiq: Move the definition of the xrx200-net node to vr9.dtsi
This removes a lot of duplicate register and interrupt definitions by
moving the xrx200-net definition to vr9.dtsi and making all devices re-
use it.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48547
2016-01-29 00:42:45 +00:00
Felix Fietkau
d4fe52c16d lantiq: fix PHY state handling issue
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48546
2016-01-29 00:42:38 +00:00
Felix Fietkau
57776e68ce base-files: remove default /etc/config/network, generate it via board.d instead
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48493
2016-01-25 16:30:41 +00:00
Felix Fietkau
d4ca4ae070 lantiq: Fix enabling CONFIG_MTD_UIMAGE_SPLIT
r48381 added CONFIG_MTD_SPLIT_UIMAGE_FW=Y to the lantiq kernel
configuration. That unfortunately contains a typo since the "y" has to
be lower-case. This leads to the kernel asking whether the config
symbol should be enabled and thus breaking the build.

FIXES: r48381/feab990887b4: lantiq: Enable the uImage mtd splitter
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48389
2016-01-20 08:40:44 +00:00
Felix Fietkau
e3b3b7fb0a lantiq: Enable the uImage mtd splitter
Until linux 4.1 the lantiq target used CONFIG_MTD_UIMAGE_SPLIT=y. That
option however is only available until linux 4.3 - thus it was not added
to lantiq's 4.4 kernel config (in r48307). This results in broken images
for devices which are using uImages. This fixes #21652

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48381
2016-01-19 22:48:37 +00:00
Hauke Mehrtens
13b8b8c2e7 lantiq: add support for TP-Link VR200v
This adds basic support for TP-Link VR200v.
Currently the following parts are not working: FXO, Voice, DECT, WIFI (both)

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 48328
2016-01-18 20:40:03 +00:00
Felix Fietkau
e7846156f2 lantiq: drop linux 4.1 support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48323
2016-01-18 15:54:23 +00:00
Felix Fietkau
9b4b2b4e17 lantiq: switch to linux 4.4
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48322
2016-01-18 15:54:18 +00:00
Felix Fietkau
6cec31da3c lantiq: fix VDSL device detection with Linux 4.4
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48319
2016-01-18 15:35:17 +00:00
Felix Fietkau
f577cb25c0 lantiq: Add support for linux 4.4
The following patches were dropped because they are already applied
upstream:
- 0038-MIPS-lantiq-fpi-on-ar9.patch
- 0039-MIPS-lantiq-initialize-usb-on-boot.patch
- 0042-USB-DWC2-big-endian-support.patch
- 0043-gpio-stp-xway-fix-phy-mask.patch

All other patches were simply refreshed, except the following:
- 0001-MIPS-lantiq-add-pcie-driver.patch
  Changes to arch/mips/lantiq/xway/sysctrl.c (these changes disabled
  some PMU gates for the vrx200 / VR9 SoCs) were removed since the
  upstream kernel disables unused PMU gates automatically (since
  95135bfa7ead1becc2879230f72583dde2b71a0c
  "MIPS: Lantiq: Deactivate most of the devices by default").
- 0025-NET-MIPS-lantiq-adds-xrx200-net.patch
  Since OpenWrt commit 55ba20afcc drivers
  should use of_get_mac_address(). of_get_mac_address_mtd is not
  available for drivers anymore since it's called automatically within
  of_get_mac_address().
- 0028-NET-lantiq-various-etop-fixes.patch
  Same changes as in 0025-NET-MIPS-lantiq-adds-xrx200-net.patch

While refreshing the kernel configuration SPI support had to be moved to
config-4.4 because otherwise M25P80 was disabled.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48307
2016-01-18 11:40:19 +00:00
Felix Fietkau
d64465556c lantiq: Remove incorrect PCIe compatible strings
Re-defining the compatible property is not required since the correct
value is inherited from vr9.dtsi.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48295
2016-01-17 19:56:16 +00:00
Felix Fietkau
720f599c9a lantiq: Remove the old SPI driver patch
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48294
2016-01-17 19:56:10 +00:00
Felix Fietkau
04ad02d132 lantiq: Switch to the new SPI driver
Compared to the "old" driver:
- Each device must assign a pinctrl setting to the SPI node to allow the
  new SPI driver to configure the SPI pins.
  While here we are also using separate input and output settings so we
  are independent of whether the bootloader configures the pins correctly.
- We use the new "compatible" strings to make the driver choose the
  correct number of chip-selects for each SoC.
- The new driver starts counting the chip-selects at 1 (instead of 0, like
  the old one did). Thus we have to adjust the devices accordingly.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48293
2016-01-17 19:56:03 +00:00
Felix Fietkau
5985c56ec6 lantiq: Add a rewritten version of the SPI driver
The new driver provides a few improvements over the old one:
- Separate compatible strings per SoC type (this allows removing some
  hardcoded of_device_is_compatible() checks)
- It does not rely upon spi-bitbang anymore
- chip-selects are numbered as in the datasheet (= starting at 1 instead
  of 0)

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48292
2016-01-17 19:55:55 +00:00
Felix Fietkau
af857db692 lantiq: Disable CONFIG_SPI_GPIO
All devices are now using the HW SPI driver, so this is not necessary
anymore.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48291
2016-01-17 19:55:48 +00:00
Felix Fietkau
d5c5928d6b lantiq: Enable the hardware SPI driver on the DGN3500/DGN3500B
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48290
2016-01-17 19:55:42 +00:00
Felix Fietkau
d8b74320bd lantiq: Enable SPI for the EASY80920 board again
Also switch to the SPI definition provided by vr9.dtsi

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48289
2016-01-17 19:55:37 +00:00
Felix Fietkau
be8f9ad6f4 lantiq: Switch FRITZ3370 from spi-gpio to the hardware SPI driver
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48288
2016-01-17 19:55:31 +00:00
Felix Fietkau
9d558fb48e lantiq: Re-use the SPI node from vr9.dtsi in TDW89X0.dtsi
This removes the duplicate SPI register definition.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48287
2016-01-17 19:55:25 +00:00
Felix Fietkau
a5c177943b lantiq: Add the SPI node to ar9.dtsi and vr9.dtsi
This allows devices to use SPI without having to re-define (and thus
duplicating) the whole SPI node.
By default SPI is disabled (as before) because only few devices need it.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48286
2016-01-17 19:55:17 +00:00
Felix Fietkau
3f8a426056 lantiq: Configure the PCIe reset GPIO using OF
After the latest pinctrl backports there are only 50 (instead of 56 as
before) GPIOs/pins exported (thus the first GPIO on VRX200 SoCs is now
462, before it was 456). This means that any hardcoded GPIOs have to be
adjusted.
This broke the PCIe driver (which seems to be the only driver which uses
hardcoded GPIO numbers), it only reports:
	ifx_pcie_wait_phy_link_up timeout
	ifx_pcie_wait_phy_link_up timeout
	ifx_pcie_wait_phy_link_up timeout
	ifx_pcie_wait_phy_link_up timeout
	ifx_pcie_wait_phy_link_up timeout
	pcie_rc_initialize link up failed!!!!!

To prevent more of these issues in the future we remove the hardcoded
PCIe reset GPIO definition and simply pass it via device-tree (like the
PCI driver does).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48285
2016-01-17 19:55:10 +00:00
Felix Fietkau
1204a1b1e5 lantiq: Use the new pinctrl compatible strings
These were introduced in upstream commit
be14811c03cf "pinctrl/lantiq: introduce new dedicated devicetree
bindings" and finally allow us to use the individual pins within our dts
(for example spi_clk, etc.).
Please note that this changes the number of GPIOs which are available for
some SoCs. VRX200 SoCs for example only have 50 pins, but previously 56
pins were exposed. This means that all places which are using hardcoded
GPIO numbers (which are not passed via device-tree) need to be adjusted
(because the first GPIO number is now 462, instead of 456).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48284
2016-01-17 19:55:04 +00:00
Felix Fietkau
ee03fc430d lantiq: Backport upstream pinctrl-xway patches from 4.5
Upstream commit be14811c03cf2 "pinctrl/lantiq: introduce new dedicated
devicetree bindings" allows us to use each pin in the pinmux. This is
useful for example in the "spi" group which contains some pins which
are inputs, and some which are outputs.
These can only be used once the new compatible strings for the pinctrl
node are used.
Additionally 0150-lantiq-pinctrl-xway.patch and the "GPIO PORT3 fix"
(which was part of 0012-pinctrl-lantiq-fix-up-pinmux.patch) were
replaced with their upstream variants which are also in 4.5.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48283
2016-01-17 19:54:59 +00:00
Felix Fietkau
deb4c31da4 lantiq: Fixed brnImage signature for the VGV7510KW22BRN images
The old signature only worked because brnboot ignores the leading "5" in
the signature. We can see the correct signature when flashing a brnImage
via recovery web-interface, in this case brnboot reports:
	[CGI-Signature Check] buf:[BRNDA6431], sigInFlash:[BRNDA6431]

Thanks to Mathias Kresin for reporting this.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48269
2016-01-17 10:47:10 +00:00
Felix Fietkau
7c0260117f lantiq: Switch to the generic mtdsplit parser implementations
This removes the arch-specific mtdsplit parsers and enables the generic
implementations for brnImage, EVA and TP-Link instead.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 48264
2016-01-17 10:41:46 +00:00
Hauke Mehrtens
cb6b7be43f lantiq: remove clk_round_rate() patch
This patch was merged into upstream Linux 4.1.
This fixes #21587 and was introduced in r48223.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 48229
2016-01-13 20:46:12 +00:00
Hauke Mehrtens
93b50ade93 kernel/4.1: update to version 4.1.15
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 48223
2016-01-12 20:51:34 +00:00
John Crispin
8c80e915a0 lantiq: Add the xbar to vr9.dts
linux 4.4 (since commit 08b3c894e56580b8ed3e601212a25bda974c3cc2
"MIPS: lantiq: Disable xbar fpi burst mode") requires that the xbar is
defined in the .dts of vrx200 (VR9) SoCs.

SVN-Revision: 48056
2016-01-01 21:21:00 +00:00
John Crispin
6f95d749d6 lantiq: match default xdsl mode and default wan interface
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48047
2016-01-01 21:19:32 +00:00
John Crispin
a9896bf106 lantiq: convert vendorid into human readable form
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48046
2016-01-01 21:19:27 +00:00
John Crispin
436fdee272 lantiq: add the current profile to the stats output
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48045
2016-01-01 21:19:21 +00:00
John Crispin
28a700de9b lantiq: TDW8980 - use devicename:colour:function led naming scheme
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48044
2016-01-01 21:19:12 +00:00
John Crispin
c584aed6b1 lantiq: P2812HNUFX - move usb leds to P2812HNU-F1
The P2812HNU-F3 doesn't have usb leds. Only the P2812HNU-F1 has those
leds.

Reported-by: Sylwester Petela <sscapi@gmail.com>
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48043
2016-01-01 21:18:59 +00:00
John Crispin
3cbfc74cde lantiq: use devicename:colour:function led naming scheme
The leds of the following boards are not renamed due to lack of
manuals/informations:

- ARV7519PW
- ARV7510PW22
- ARV4510PW

The leds of the ARV4518PWR01* boards are unchanged, since the leds doesn't
match the leds from the manual or pictures (e.g. there shouldn't be a wps led).

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48042
2016-01-01 21:18:54 +00:00
John Crispin
4cf3fd49fc lantiq: add support for indicating the boot state using three leds
The BTHOMEHUBV5A has a RGB power led, where every colour is perfect to
indicate the current boot state. This patch adds support for such cases.

The existing led sequences should be the same as before.

Boards which are using a led different from power (like TDW89x0) are
changed to switch of the led after boot

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48041
2016-01-01 21:18:47 +00:00
John Crispin
ebc71a4d16 lantiq: use dsl led defined in DTS
dsl_control (dsl_notify.sh) is the only process which is aware of the
state of the atm/ptm interface. Use the dsl led exclusive for the dsl
line state.

On boards which don't have a distinct internet and a dsl led, let the
netdev status of the atm interface trigger the shared led.

Triggering the shared led according to the status of the ppp interface
isn't suitable, since the led would be switched of if the ppp
connection goes down, but the line is still in sync.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48040
2016-01-01 21:18:38 +00:00
John Crispin
a3c3b2a9a8 lantiq: use power leds defined in DTS
Use the power leds defined in the dts file instead of hardcoded led names.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48039
2016-01-01 21:18:30 +00:00
John Crispin
d7a5d66ea1 lantiq: use default leds defined in DTS
Remove all now double defined leds from the led board file. Use pppoe
as default for all broadband connections, since it's the default in
OpenWrt now.

Rename the the wifi leds to make sure, the not applicable default
values get overwritten.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48038
2016-01-01 21:18:21 +00:00
John Crispin
a3042500ab lantiq: define default leds in dts files
- ARV7525PW: use the power led as dsl led as done by the stock firmware
- FRITZ3370: use the info led as internet led
- FRITZ7320: use the power led as dsl led as done by the stock firmware

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48037
2016-01-01 21:18:08 +00:00
John Crispin
5b6f0250f6 lantiq: ARV752DPW - fix dts file
Use the same led logic and labels as the OEM firmware (red = okay,
blue = failure).

Add the red internet led.

Remove missing usb led workaround. The workaround shouldn't be in the
default configuration.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48036
2016-01-01 21:18:00 +00:00
John Crispin
aa99acdb46 lantiq: ARV752DPW22 - fix dts file
No need to switch (and keep) on all leds at boot. Use the same led
logic and labels as the OEM firmware (red = okay, blue = failure).

Add the red internet led.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48035
2016-01-01 21:17:55 +00:00
John Crispin
2eead1c891 lantiq: DGN1000B - fix typo in dts file
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48034
2016-01-01 21:17:50 +00:00
John Crispin
e557011041 lantiq: ARV4518PWR01* move redundant parts to dtsi
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48033
2016-01-01 21:17:42 +00:00
John Crispin
b6b128f63d lantiq: BTHOMEHUBV2B - remove missing usb led workaround
The workaround shouldn't be in the default configuration.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48032
2016-01-01 21:17:34 +00:00
John Crispin
56fa6d8241 lantiq: P2812HNUFX - move leds to dtsi
Beside the used labels, they are the same on both boards.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48031
2016-01-01 21:17:26 +00:00
John Crispin
8d5ac2d0f1 lantiq: fix Image Builder
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 48002
2015-12-23 19:25:55 +00:00
John Crispin
c01ca020ea lantiq: fix PCI_DEVICE_ID_LANTIQ_PCIE
It's not necessary to define PCI_* if pci_ids.h is included a few
lines above.

The change to pci_ids.h doesn't look intentional to me, especially
since the former value is added to the top of ifxmips_fixup_pcie.c.

Both changes were introduced with the kernel 4.1 support patches and
were not present in the 3.18 patches.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 47996
2015-12-23 18:25:22 +00:00
John Crispin
e33aa71045 lantiq: TDW89x0 - increase spi frequency
Use the same max spi frequency as set in u-boot.

According to the datasheets, the Q64-104HIP as well as the Winbond
25Q64FVSIG support spi frequencies up to 50 MHz. During my tests, the
Q64-104HIP couldn't be recognized/initialized if the frequency
was > 40MHz.

Both chips do support fast read as well.

While touching the dts file, I fixed the dtc compiler warnings.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 47994
2015-12-23 18:24:56 +00:00
John Crispin
3af2cf661b lantiq: disable SW_PORTMAP usage in the ethernet driver
using the special tag in this way lead to port mirroring for certain types of traffic.
fallback to using th PMAC_EWAN register for the wan portmap.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47993
2015-12-23 18:24:43 +00:00
John Crispin
5e10f67b67 lantiq: Configure LED polarity for TDW8970 and TDW8980.
This patch configures the correct ath9k WLAN LED polarity for the TDW8970,
and for the TDW8980 as well.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 47969
2015-12-23 14:42:25 +00:00
John Crispin
21493c984a lantiq: fix ARV7519RW22 buttons
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47918
2015-12-17 09:28:29 +00:00
John Crispin
0a6a37be83 lantiq: add the TDW8980 5GHz led
Still unused, but u-boot doesn't take care of the led, which results in a
permanent switched on 5GHz LED.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 47915
2015-12-17 09:28:01 +00:00
John Crispin
ab77d4bcb9 lantiq: Fix LED handling.
- Use common OpenWrt blink patterns instead of custom ones
- Add preinit_regular hook
- Handle the TDW89X0 that does not have a configurable power LED

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 47914
2015-12-17 09:27:52 +00:00
John Crispin
34934609f9 lantiq: Configure LED polarity for TDW8970.
This patch configures the correct ath9k WLAN LED polarity for the TDW8970.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 47913
2015-12-17 09:27:46 +00:00
John Crispin
ec21c9821c lantiq: Configure disabled WLAN bands for TDW89X0.
The TDW8970 has a AR9381, which is the bgn 3x3:3 variant of the AR938x family.

The TDW8980 has a AR9287, which is the bgn 2x2:2 variant of the AR928x family.

This means that the chip for both routers is 2.4 GHz only.

Anyway, the manufacturer didn't disable the 5 GHz band in the EEPROM partition
(at least on my TDW8970).

So this patch disables the 5 GHz band.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 47912
2015-12-17 09:27:40 +00:00
John Crispin
f2fd516d72 lantiq: Allow configuration of ath9k disabled bands and LED polarity from the device tree.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 47911
2015-12-17 09:27:31 +00:00
Jo-Philipp Wich
67e1c87012 all: drop old uci-defaults.sh
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47867
2015-12-11 15:26:06 +00:00
John Crispin
0938233fcd lantiq: get rid of ltq-vdsl-fw
Because of dsl-vrx200-firmware-xdsl-* there's no need anymore to
download a dsl firmware at runtime.

Signed-off-by: Andre Heider <a.heider@gmail.com>

SVN-Revision: 47851
2015-12-11 15:05:40 +00:00
John Crispin
787120e3a3 lantiq: fix led setup after switch to uci-defaults-new.sh
The switch to uci-defaults-new.sh revealed a bug in the former used
uci-defaults.sh, which failed to add leds with colons in the led name.

This bug isn't any longer present in uci-defaults-new.sh and therefore
all via DT defined leds will be added to /etc/config/system with their initial
on/off state, regardless whether they are already added by the board specific
led mappings.

This results for a BTHOMEHUBV5A into the following led configuration:

- soc:blue:power is added as led_power with the initial state "switched on"
- soc:blue:power is added as led_soc_blue_power with the initial state "switched off"

With the final result of a switched off power led after boot.

The only led that needs to be added is the BTHOMEHUBV5A specific dimmed led.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 47850
2015-12-11 15:05:30 +00:00
Jo-Philipp Wich
9157360ac5 lantiq: fix logic error in dsl board.d code
Starting with r47755 the pppoe wan interface section isn't any longer added to
the network config on firstboot, using the default configuration. Since the
commit message does not mention such a change, I assume that this wasn't
intentionally.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 47793
2015-12-06 08:41:22 +00:00
Felix Fietkau
ec1b121769 lantiq: add VDSL2 vectoring status information
Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 47785
2015-12-05 09:52:42 +00:00
Felix Fietkau
e82404ce6c lantiq: get rid of the dsl_fw mtd partition
Now that we have redistributable vdsl/adsl firmware blobs in /lib/firmware,
we can drop the dsl_fw partition and extend the firmware partition.

Signed-off-by: Andre Heider <a.heider@gmail.com>

SVN-Revision: 47783
2015-12-05 09:52:30 +00:00
Felix Fietkau
fff859a1f6 lantiq: remove 3.18 support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47774
2015-12-05 09:51:25 +00:00
Felix Fietkau
8b30afb005 lantiq: fix a race condition in the SPI driver leading to rx FIFO overflows (and subsequent timeouts)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47770
2015-12-04 20:26:22 +00:00
Felix Fietkau
9330296932 lantiq: re-enable spi-xway for TD-W89X0 now that it is fixed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47768
2015-12-04 18:35:20 +00:00
Felix Fietkau
b963cec01c lantiq: fix xway spi driver timeout issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47767
2015-12-04 18:35:12 +00:00
Felix Fietkau
ae10274239 lantiq: clean up the xrx200 ethernet driver and fix stability issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47766
2015-12-04 17:44:06 +00:00
Felix Fietkau
435e7fb295 lantiq: move esi calls to dsl_cpe_control scripts to fix ordering wrt. loading vr9 drivers
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47764
2015-12-04 17:42:51 +00:00
Jo-Philipp Wich
5ebc5de49d lantiq: switch from uci-defaults to board.d
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47755
2015-12-04 12:32:44 +00:00
Felix Fietkau
46112609d0 lantiq: fix up m25p80 device ids (#20975)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47690
2015-12-02 17:20:39 +00:00
Hauke Mehrtens
34e0d3cb5a lantiq: fix compile error
This fixes a problem introduced in r47624.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47628
2015-11-24 20:12:21 +00:00
Felix Fietkau
bb1c915f1e kernel: update m25p80 in 4.1 to the latest version from 4.4-rc1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47624
2015-11-24 18:59:28 +00:00
John Crispin
570c35a599 lantiq: add phy led config support over devicetree bindings
This patch adds the posibility to config the led behaviour of the lantiq phys
over the devicetree bindings.It patches the 0023-NET-PHY-adds-driver-for-lantiq-PHY11G
for 3.18 and 4.1. I have also added a register description overview for
applicable values. This goes to the documentation folder in the linux kernel.

Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>

SVN-Revision: 47566
2015-11-21 21:25:43 +00:00
John Crispin
0206a400cf lantiq: tweak DWC2 default parameters
This patch improves the default configuration of DWC2 on lantiq SoCs
somewhat:
 * Set maximum packet count to largest allowed value by the DWC2 (511)
 * Use 16-bit DMA bursts
 * Divide fifo buffers more evenly

Default fifo buffer sizes from original ltq-hcd driver seem really
irrational. For example according to DWC2 data book rxfifo size of 240
will not fit even a single full length USB packet. On the other hand
non-periodic tx fifo size of 240 is more than enough to fit one complete
packet.

Change the sizes around to improve the situation and to fix some issues
especially with isochronous USB transfers.

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>

SVN-Revision: 47563
2015-11-21 21:25:20 +00:00
Hauke Mehrtens
ff64ae8293 lantiq: add clk_round_rate()
This adds a basic implementation of clk_round_rate()
The clk_round_rate() function is called by multiple drivers and
subsystems now and the lantiq clk driver is supposed to export this,
but doesn't do so, this causes linking problems like this one:
ERROR: "clk_round_rate" [drivers/media/v4l2-core/videodev.ko] undefined!

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47254
2015-10-25 22:46:46 +00:00
Hauke Mehrtens
da94b00df5 kernel: update kernel 4.1 to version 4.1.11
https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.11

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47252
2015-10-25 17:32:01 +00:00
John Crispin
e1d585d99f lantiq: Synchronize access to the DSL command pipe
Whenever two processes were executing different commands at the same
time then one of the commands sometimes got the response of the other
command.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 47213
2015-10-19 10:08:56 +00:00
John Crispin
b7e4c8d3bf lantiq: Print the status register whenever an error occurs
This should help finding potential problems with the SPI driver.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 47209
2015-10-19 10:08:29 +00:00
John Crispin
2c7d536780 lantiq: Fixed reading the number of RX FIFOs in the SPI driver
Until now the SPI driver used the TX bits for the RX FIFO. This seems
uncritical for now since both are equals on my devices (VR9), but this
could cause problems on other SoCs.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 47208
2015-10-19 10:08:18 +00:00
John Crispin
42c9a85e8e Revert "lantiq: activate spi-xway on TDW89X0"
This reverts commit 68c2e4789b4f071ee75d39248f4d08fe8283eb28.

commit r47159 was bad

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47207
2015-10-19 10:08:12 +00:00
John Crispin
f457ae99f2 lantiq: fix use of IRQF_DISABLED in lantiq kmods
The IRQF_DISABLED flag was removed in kernel 4.1 with commit
"genirq: Remove the deprecated 'IRQF_DISABLED' request_irq() flag entirely" [1].

Therefore the compilation of ltq-hcd and ltq-vmmc kmods fails.

[1] https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=d8bf368d0631d4bc2612d8bf2e4e8e74e620d0cc

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 47180
2015-10-11 16:24:43 +00:00
John Crispin
2fc473cf3f lantiq: bugfix wrong non pre-emptive crc errors output
This patch fixes a wrong non pre-emptive crc errors output of
dsl_control.sh status.

Signed-off-by: Luca Debernardi <luca.debernardi@gmail.com>

SVN-Revision: 47172
2015-10-11 16:23:26 +00:00
John Crispin
02197db96f lantiq: activate spi-xway on TDW89X0
use the hardware spi core in favour of spi-gpio.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47159
2015-10-07 12:12:48 +00:00
John Crispin
33f9165a63 lantiq: spi driver fix
adds a missing wait busy. based on the UGW patch 2060..

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47158
2015-10-07 12:12:35 +00:00
John Crispin
2210e821e1 lantiq: bugfix luci lantiq_dsl status
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Helge Mader <hmader@tdt.de>
Reported-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47152
2015-10-07 08:00:54 +00:00
John Crispin
a0543c2bdc lantiq: several ARV7519RW22 fixes
Fixes ARV7519RW22 flash register (only 1 flash).
Power LED is green, not red.
Rename message LEDs to internet.
Add LEDs configuration (lan, wan, power).
Enable switch VLANs.
Fix secondary USB.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com>

SVN-Revision: 47132
2015-10-05 10:28:34 +00:00
John Crispin
2795592d91 lantiq: make v4.1 the default kernel
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47131
2015-10-05 10:28:26 +00:00
John Crispin
161179f40b lantiq: Add target TP-Link TD-W8980
The device is similar to the TD-W8970, beside a different Atheros 2.4 GHz
wireless chip and the additional, PCI connected, WAVE300 5 GHz wireless.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 47130
2015-10-05 10:28:19 +00:00
John Crispin
f2f50ad762 lantiq: fix ath_pci_fixup hang on bridged devices
Port of r41856.

In contrast to the brcm63xx target, it isn't sufficient to enable/disable
the bridge. The device needs to be enabled/disabled to fix the hang. The
bridge will be automatically enabled by the time the connected device is
enabled.

Fixes boot on TD-W8980.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 47129
2015-10-05 10:28:12 +00:00
John Crispin
c5cc3d9610 lantiq: Change the data-type of mac address in ETOP driver
This adds the changes from r46219 to the linux 4.1 patches as well.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 47128
2015-10-05 10:28:07 +00:00
John Crispin
cea7c66ef8 lantiq: bugfix uninitialized variables
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Reported-by: Sylwester Petela <sscapi@gmail.com>

SVN-Revision: 47127
2015-10-05 10:27:55 +00:00
Matteo Croce
70da7324cd lantiq: fix binutils 2.15.1 build
SVN-Revision: 47105
2015-10-04 22:03:04 +00:00
Hauke Mehrtens
0cd478518f kernel: update 4.1 to 4.1.10
Fixes a regression on spi flash devices (upstream commit 1583eaece6fa).

Changelogs:
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.7
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.8
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.9
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.10

096-ipv4-off-by-one-in-continuation-handling-in-proc-net.patch was applied
upstream and dropped.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>
[update from 4.1.9 to 4.1.10]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47104
2015-10-04 11:34:39 +00:00
Rafał Miłecki
90e1b84f15 lantiq: update list on NAND devices in platform_pre_upgrade
Meanwhile BTHOMEHUBV5A board was added.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46941
2015-09-15 11:49:33 +00:00
John Crispin
57c8708d64 lantiq: add platform_pre_upgrade for sysupgrade
As explained in recent sysupgrade/nand.sh commits, current NAND
sysupgrade is a bit misleading because of nand_do_platform_check
behavior. It leaves a special mark in /tmp/sysupgrade-nand-path
triggering some diffent code path in nand_upgrade_stage1.

The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.

Please note that because of current nand_upgrade_stage1 implementation
this patch doesn't change any behaior yet. It only prepares lantiq
target for changing nand_do_platform_check (it will be possible after
preparing all other targets as well).

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46939
2015-09-15 06:13:07 +00:00
John Crispin
06a180d027 lantiq: get more status information from xDSL
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Helge Mader <hmader@tdt.de>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Andre Heider <a.heider@gmail.com>

SVN-Revision: 46917
2015-09-14 20:08:39 +00:00
John Crispin
404b183aa8 lantiq: Add AR9 compatibility bits to DWC2 driver
Add AR9 DTS definition to be recognized by the DWC2 driver.

The same driver parameters can be mostly used except that some boards
seem to erroneously report OTG HNP/SRP capability of the USB HCD.
Forcing the HNP/SRP off allows these boards to work with the DWC2 as well.

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>

SVN-Revision: 46915
2015-09-14 20:08:15 +00:00
John Crispin
4595440215 lantiq: Introduce DWC2 compatible DTS definitions for AR9 USB
Since the AR9 USB is very similar to the VR9 USB it too can be used with
the upstream DWC2 driver.

Here are the DTS definitions which make it compatible with the DWC2
driver.

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>

SVN-Revision: 46914
2015-09-14 20:08:07 +00:00
John Crispin
1f4124ceb0 lantiq: Initialize USB on AR9 platform
Based on the ltq-hcd driver the AR9 USB can be initialized the same way
as the VR9 platform. Use the same initialization bits for both
platforms.

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>

SVN-Revision: 46913
2015-09-14 20:07:23 +00:00
Hauke Mehrtens
89ce027c08 kernel: add CONFIG_MIPS_CDMM config option
This driver was added in kernel 4.1.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 46881
2015-09-11 20:31:32 +00:00
Felix Fietkau
6c1adb3eec lantiq: Use the BAR0 base address in the ath PCI fixup code
Fixes support for AR9287 on TP-Link TD-W8980 and possibly other devices
which have an ath wifi chip at a PCI address other than 0xb8000000
(TD-W8980 for example has it's wifi chip at 0xbc000000).

Signed-off-by: Geoffrey McRae <geoff@spacevs.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 46869
2015-09-11 16:35:46 +00:00
Jonas Gorski
7d6cff4882 kernel: update 3.18 to 3.18.21
Changelog:
 * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.21

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46768
2015-09-02 10:18:15 +00:00
Jonas Gorski
1bc35a08d1 lantiq: remove dead EASY33016 image recipe
Support for lantiq_svip_be has been removed a while ago, so EASY33016
images weren't buildable anymore. Remove the recipes as well as gzip
compressed kernel support, as EASY33016 was the last user of it.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46760
2015-08-30 12:18:22 +00:00
Jonas Gorski
2d379e796f kernel: update 4.1 to 4.1.6
Changelog:
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.6

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46713
2015-08-23 18:06:11 +00:00
John Crispin
4582d7e8f5 lantiq: Support newer versions of the PEF7071 ethernet PHYs
The BT Home Hub 5A uses three PEF7071 with PHY ID 0xd565a401. Daniel's
PHY driver (for his u-boot sources) already supports that PHY because
it uses a PHY ID mask of 0xfffffff8.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 46670
2015-08-17 11:25:57 +00:00
Jonas Gorski
bed330204a image.mk: move KDIR_TMP definition to a central location
Instead of each target defining it the same, move the KDIR_TMP
definition to include/image.mk. In addition Image/Build/SysupgradeNAND
already requires KDIR_TMP to be set, so it makes sense to have it
globally defined.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46592
2015-08-14 10:20:53 +00:00
Jonas Gorski
dbe4173b20 image: fix jffs2(_nand) image generation
Variables dependend on JFFS2_BLOCKSIZE and NANDBLOCK_SIZE are used
for template generation, so need to be present before inclusion of
image.mk in target image Makefiles.
So move all declarations to before any includes.

Fixes: r42878 ("image.mk: clean up and parallelize mkfs calls")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46564
2015-08-05 13:55:52 +00:00
Jonas Gorski
caa73eb95c kernel: update 4.1 to 4.1.4
Changelog:
 * https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.4

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[jogo: fix brcm2708 patches, refresh target patches]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46560
2015-08-05 13:55:14 +00:00
John Crispin
9c0ed4ce5c lantiq: Silence the PCIe error interrupt printk also in 4.1
This ports 9e2a7b779e6f0914395da3657b00f0ac00209bfd to the 4.1 patches.
I forgot this when preparing the initial 4.1 patch.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 46453
2015-07-24 09:09:07 +00:00
Jonas Gorski
cc42b1049b kernel: refresh patches for 4.1
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46441
2015-07-22 12:51:11 +00:00
Hauke Mehrtens
29039f51b3 kernel: refresh patches on linux 3.18
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 46308
2015-07-12 13:47:16 +00:00
John Crispin
b9963bbe80 lantiq: Add support for Arcadyan ARV8539PW22 (Speedport W 504V)
lantiq: Add support for Arcadyan ARV8539PW22 (Speedport W 504V)

Signed-off-by: Jannis Pinter <jannis@pinterjann.is>

SVN-Revision: 46224
2015-07-07 13:44:58 +00:00
John Crispin
6bdd209f15 lantiq: Add support for the BT Home Hub 5A
u-boot support depends on the next "upstream" version ([0]) from
Daniel Schwierzeck.
Since the installation process is quite complicated a "how to" was
added to the wiki: [1]

[0] https://github.com/danielschwierzeck/u-boot-lantiq/tree/openwrt/v2014.01-next
[1] http://wiki.openwrt.org/toh/bt/homehub_v5a

V2: Use the correct PCI interrupt (fixes 2.4GHz wifi)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 46223
2015-07-07 13:44:53 +00:00
John Crispin
2748df1c98 lantiq: Silence the printk when a PCIe error interrupt arrives
Basically the only error I am seeing is "Correctable Error". Also newer
lantiq PCIe drivers have this message wrapped in a "if debug enabled"
block. So it should be safe to disable this warning.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 46222
2015-07-07 13:44:37 +00:00
John Crispin
415fe71d00 lantiq: Make the MEI address available for kernel drivers
Newer DSL driver versions depend on the address information.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 46221
2015-07-07 13:44:32 +00:00
John Crispin
fa9e259729 lantiq: Change the data-type of mac address in ETOP driver
Make it consistent with the net_device struct and the xrx200 driver

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 46219
2015-07-07 13:44:12 +00:00
John Crispin
ff08b09570 lantiq: Add support for linux 4.1
All (still relevant) patches were refresh.
The following patches were dropped because they are applied upstream:
- 0003-MIPS-lantiq-handle-vmmc-memory-reservation.patch
- 0005-MIPS-lantiq-add-reset-controller-api-support.patch
- 0006-MIPS-lantiq-reboot-gphy-on-restart.patch
- 0009-MIPS-lantiq-command-line-work-around.patch
- 0010-MIPS-lantiq-export-soc-type.patch
- 0011-lantiq-add-support-for-xrx200-firmware-depending-on-.patch
- 0037-MIPS-lantiq-move-eiu-init-after-irq_domain-register.patch

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 46216
2015-07-07 13:43:47 +00:00
Jonas Gorski
901a7fa067 kernel: update 3.18 to 3.18.17
Changelog:
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.17

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46150
2015-06-30 23:26:09 +00:00
Jonas Gorski
9a59b350b7 kernel: update 3.18 to 3.18.16
Changelogs:

* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.15
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.16

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46011
2015-06-17 09:54:55 +00:00
John Crispin
262f6869a2 lantiq: Backport gpio-stp-xway to fix the highest bits of the PHY LEDs
This fixes the LAN2 LED on Arcadyan VGV7510KW22.

SVN-Revision: 45899
2015-06-05 14:11:51 +00:00
John Crispin
ca1db6b5ce lantiq: Add support for Arcadyan VGV7510KW22 (known as o2 Box 6431)
SVN-Revision: 45897
2015-06-05 14:11:36 +00:00
John Crispin
2575637497 lantiq: Make the CRC32 poly value configurable per device
This also adds the old hardcoded value to the VGV7519BRN profile to make
sure that images are still generated correctly.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 45882
2015-06-03 13:58:57 +00:00
Jonas Gorski
43c0a725af lantiq: fix VG3503J rootfs offset
In r44391 the kernel partion size was increased to allow larger kernels,
but the rootfs partition offset was missed. Fix this by setting the
rootfs offset to the expected value.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45868
2015-06-01 12:37:24 +00:00
John Crispin
b34988d5d0 lantiq: fix imagebuilder
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45851
2015-05-30 20:28:57 +00:00
John Crispin
230efe318f lantiq: Fix initialization of the PCI IRQs when PCIe is also enabled
There are already ifx_pcie_bios_{map_irq,plat_dev_init} hooks defined in
ifxmips_pcie.c. Instead of defining a new hook we simply re-use the
existing ones (this is basically what the lantiq BSP code does).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 45718
2015-05-23 15:25:59 +00:00
John Crispin
390924e662 lantiq: Fix PCIe bus when PCI is also enabled.
The PCIe bus seems to require a hack/workaround when PCI is enabled as
well. Unfortunately this is guarded by an CONFIG_IFX_PCI ifdef, which is
only defined in lantiq's BSP code. The config symbol for the upstream
lantiq PCI driver is CONFIG_PCI_LANTIQ.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 45717
2015-05-23 15:25:51 +00:00
Jonas Gorski
76d079204d kernel: update 3.18 to 3.18.14
Changelogs:

* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.12
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.13
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.14

Build tested on brcm63xx and ipq806x, runtested on brcm63xx.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45711
2015-05-21 19:32:46 +00:00
Imre Kaloz
f86c07d8d4 The ability to read MAC addresses from MTD is useful for other targets besides ramips and lantiq as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 45596
2015-05-03 17:56:32 +00:00
John Crispin
85bf288428 lantiq: remove arphaned folder
the new buildbot was picking this up as a valid target.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45068
2015-03-27 19:47:22 +00:00
John Crispin
29cf72ac07 lantiq/xrx200: cleanup default packages
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44867
2015-03-17 09:44:06 +00:00
John Crispin
986af9e64e lantiq: make xrx200 targets use the upstream dwc2 driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44857
2015-03-17 09:42:56 +00:00
John Crispin
257671615b lantiq: drop 3.14 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44812
2015-03-16 07:39:52 +00:00
Felix Fietkau
d8d9282372 lantiq: add a better fix to strip FCS from ethernet packets on XRX200
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 44771
2015-03-15 09:47:34 +00:00
Felix Fietkau
55cdb4dbb3 lantiq: enable atm-esi by default for xrx200
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 44769
2015-03-15 07:57:51 +00:00
John Crispin
da3fd5dbf9 kenrel: refresh patches
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44678
2015-03-11 17:08:46 +00:00
John Crispin
d5c250b91a lantiq: make the new dwc2 support only work for vr9
danube needs to be added

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44677
2015-03-11 17:08:40 +00:00
John Crispin
2a390925df lantiq: Convert Zyxel P-2812HNU-FX and TP-Link TD-W8970 to support dwc2
Here the device tree entry for ifxhcd is listed as compatible with one
supported in dwc2 (after patching the dwc driver appropriately).

A second entry is added to support the second core of the hcd. This
entry is listed to be compatible with only dwc2. Done this way there
should be backwards support for both hcd drivers (ltq-hcd and dwc2)

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>

SVN-Revision: 44676
2015-03-11 17:08:32 +00:00
John Crispin
72822d0192 lantiq: Use platform endianness when accessing dwc2 registers
This patch switches calls to readl/writel to their
dwc2_readl/dwc2_writel equivalents which preserve platform endianness.

This patch is necessary to access dwc2 registers correctly on big
endian systems such as the mips based SoCs made by Lantiq. Then dwc2
can be used to replace ifx-hcd driver for Lantiq platforms found e.g.
in OpenWrt.

The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>

SVN-Revision: 44675
2015-03-11 17:08:26 +00:00
John Crispin
d77c857509 lantiq: Add sensible hw-defaults for dwc2
Lantiq driver does not work with autodetected fifo sizes so use ones
from original ltq-hcd driver in dwc2. Other values can be
autodetected.

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>

SVN-Revision: 44674
2015-03-11 17:08:15 +00:00
John Crispin
2ddcf4c46e lantiq: Configure gpio power output pin when initializing dwc2 usb
Port gpio code from original ltq-hcd driver to dwc2.

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>

SVN-Revision: 44673
2015-03-11 17:08:08 +00:00
John Crispin
a23da431dc lantiq: Add usb initialization bits from ltq-hcd to platform init
Add VR9 specific usb initialization bits from ltq-hcd to platform
initialization.

This patch is more of a proof-of-concept than production quality
since the initialization registers are different on other lantiq
platforms.

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>

SVN-Revision: 44672
2015-03-11 17:08:02 +00:00
John Crispin
d15ac306fa kernel: move KERNFS to generic config
KERNFS symbol is selected by SYSFS, so place it in generic config.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 44615
2015-03-06 07:56:47 +00:00
John Crispin
f04a268a04 kernel: disable ARCH_NEEDS_CPU_IDLE_COUPLED
Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since
only one platfrom (omap) needs them.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 44614
2015-03-06 07:56:34 +00:00
John Crispin
6617845711 kernel: move MTD_SPLIT_SUPPORT to generic config
CONFIG_MTD_SPLIT_SUPPORT symbol default value is 'y' and many platform
specific configs explicitly enables it, while no one platform disables
this symbol. So place it in generic config and remove from platform
specific configs.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 44612
2015-03-06 07:56:08 +00:00
John Crispin
7886cced18 kernel: remove GENERIC_NET_UTILS from platform configs
CONFIG_GENERIC_NET_UTILS is selected by CONFIG_NET and already enabled
in generic config, so we don't need this symbol in platform specific
configurations.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 44611
2015-03-06 07:55:57 +00:00
Jonas Gorski
3139140339 kernel: move CONFIG_MIPS_O32_FP64_SUPPORT to generic configs
Most MIPS targets have it disabled, so move the symbol to the generic
configs to keep target configs small.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 44583
2015-03-01 11:37:15 +00:00
John Crispin
e07c4f2150 lantiq: disable buffered writes on Intel command set flash
Some Lantiq SoCs are not able to use buffered writes properly with
Intel command set flash due to the way NOR addresses on EBU are
manipulated. This patch disables buffered writes on those devices.
The only device affected at the moment is ARV4510PW, others use
AMD/Fujitsu command set.

Signed-off-by: Matti Laakso <malaakso@elisanet.fi>

SVN-Revision: 44451
2015-02-14 20:48:32 +00:00
John Crispin
a15dd8ec78 lantiq: Fix flash for targets with NO_XIP
For targets with NO_XIP ltq_mtd->map[i].phys equals -1 and devm_ioremap fails.
Fix this by using pdev->resource[i].start instead.

Signed-off-by: Matti Laakso <malaakso@elisanet.fi>

SVN-Revision: 44450
2015-02-14 20:48:26 +00:00
John Crispin
440d9ddf7f lantiq: fix DGN3500 root device
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>

SVN-Revision: 44428
2015-02-13 07:29:17 +00:00
John Crispin
dbfb21ee90 lantiq: make m25p80 work again
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44421
2015-02-12 11:15:56 +00:00
John Crispin
1eb616764e lantiq: fix mac addr assignment inside lantiq_etop
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44420
2015-02-12 09:17:04 +00:00
John Crispin
c5b7e1aaf4 lantiq: PCI should be enabled on vrx200
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44419
2015-02-12 08:23:45 +00:00
John Crispin
f90d9d486a lantiq: fix VG3503J partition table for newer kernels
the kernel has increased and does not fit into the 1,5MB anymore.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44391
2015-02-11 10:17:38 +00:00
John Crispin
1c0c1ebc6b lantiq: td-w8970: fix failsafe mode
Fix failsafe mode for TD-W8970, register interface for preinit.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 44353
2015-02-09 12:14:48 +00:00
John Crispin
1c9dc26ce9 lantiq: td-w8970: fix reset button
For TP-LINK TD-W8970 button should work as "reset", not "BTN_1".

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 44352
2015-02-09 12:14:32 +00:00
John Crispin
826b461427 lantiq: add 3.18 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44348
2015-02-09 12:13:25 +00:00
Luka Perkov
683da1384b lantiq: fix patches after 3.14.32 bump
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44320
2015-02-08 15:09:45 +00:00
John Crispin
74b3597d07 lantiq: correct value for fpi clock on ar9
This adds a patch to target/linux/lantiq/patches-3.14
fixing a bug clock code on ar9. The current version returns
the wrong value for the fpi clock frequency in some
cases.

See discussion for further details:
https://lists.openwrt.org/pipermail/openwrt-devel/2015-January/030688.html

I'm not sure about the patch naming and numbering convention.
Do please let me know it this is not OK.

Many thanks,

Ben Mulvihill

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 44083
2015-01-23 12:32:28 +00:00
John Crispin
fcbc21890c lantiq: DGN3500 cleanups
This patch builds on the previous three to streamline support for the
Netgear DGN3500.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>

SVN-Revision: 44032
2015-01-18 09:41:04 +00:00
John Crispin
4424620c51 lantiq: Restore call to orphaned etop function
It seems the call to ltq_get_eth_mac() disappeared at some point. This
patch puts it where it currently most makes sense.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>

SVN-Revision: 44031
2015-01-18 09:40:58 +00:00
John Crispin
c80b429fc1 lantiq: Fix initscript issue
Currently this initscript fails if the macaddr has any leading zeroes.
This patch corrects the problem.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>

SVN-Revision: 44029
2015-01-18 09:40:47 +00:00
John Crispin
8cbf97e936 Remove old P2812HNUFX dts
Remove unused P2812HNUFX board definition.

Signed-off-by: Sylwester Petela <sscapi@gmail.com>

SVN-Revision: 43988
2015-01-17 07:07:21 +00:00
John Crispin
7f77870c19 Add profile and userspace for P2812HNUF1/3, switch from UBI_GLUEBI to UBI_BLOCK
Add profile and userspace for P2812HNUF1/3, switch from UBI_GLUEBI to UBI_BLOCK

Signed-off-by: Sylwester Petela <sscapi@gmail.com>

SVN-Revision: 43987
2015-01-17 07:07:15 +00:00
John Crispin
b4d2b69c43 lantiq: Add device tree for P2812HNUF1 and P2812HNUF3
Add device tree for P2812HNUF1 and P2812HNUF3.

Signed-off-by: Sylwester Petela <sscapi@gmail.com>

SVN-Revision: 43986
2015-01-17 07:07:06 +00:00
John Crispin
c9a390f9e1 lantiq: BT Home Hub 3A - userspace
BT Home Hub 3A - userspace

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 43879
2015-01-08 20:25:48 +00:00
John Crispin
9d7d29439b lantiq: BT Home Hub 3A - profile
BT Home Hub 3A - profile

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 43878
2015-01-08 20:25:41 +00:00
John Crispin
550784f1ea lantiq: BT Home Hub3A - device tree
BT Home Hub3A - device tree

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 43877
2015-01-08 20:25:35 +00:00
John Crispin
1ba71cbc14 lantiq: Fix adsl led on Home Hub 2B
This fixes the adsl led on the Home Hub 2B.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 43876
2015-01-08 20:25:28 +00:00
Felix Fietkau
5bbe758e4e lantiq: add missing NAND_WRITE_DATA in NAND driver.
Signed-off-by: Sylwester Petela <sscapi@gmail.com>

SVN-Revision: 43856
2015-01-05 21:37:21 +00:00
Felix Fietkau
c7e8b5ebbd lantiq: remove linux 3.10 support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43685
2014-12-13 11:54:57 +00:00
Felix Fietkau
9a495f6bbb kernel: refresh patches
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43564
2014-12-08 12:04:25 +00:00
John Crispin
44d703160b lantiq: Concatenate multiple flash chips for lantiq-flash
Signed-off-by: Maikel Bloemendal <openwrt@maikelenyvonne.nl>
Tested-by: Eddi De Pieri <eddi@depieri.net>

SVN-Revision: 43272
2014-11-14 17:06:04 +00:00
John Crispin
4b5c23e1e3 lantiq: vgv7519 - set some defaults for leds
Signed-off-by: Eddi De Pieri <eddi@depieri.net>

SVN-Revision: 43256
2014-11-14 16:53:53 +00:00
John Crispin
901dddce31 lantiq: set default led configuration from /sys entry later, after per board settings
Signed-off-by: Eddi De Pieri <eddi@depieri.net>

SVN-Revision: 43255
2014-11-14 16:53:48 +00:00
John Crispin
c466262d53 vgv7519: fix profile, this board have a rt2800-pci board
SVN-Revision: 43115
2014-10-30 08:08:09 +00:00
John Crispin
36e862da17 lantiq: vgv7519: fix board_config on dts, read mac address and set
Signed-off-by: Eddi De Pieri <eddi@depieri.net>

SVN-Revision: 43109
2014-10-29 20:50:40 +00:00
John Crispin
9762c54914 lantiq_dsl.sh: properly detect vdsl_cpe_control and add missing quotes
lantiq_dsl.sh didn't work with VDSL chipsets for now, fix that by
detecting whether vdsl_cpe_control or dsl_cpe_control should be used.
Also add missing quotes around shell string comparision.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 43101
2014-10-29 08:23:47 +00:00
John Crispin
4d7ae64b73 vgv7519: support more recent board release with vrx288 v1.2
The existance of this new board has been confirmed and tested by the guy on this commit

76fdd8e638

SVN-Revision: 43072
2014-10-26 17:18:41 +00:00
Felix Fietkau
c288d2d6d9 kernel: makefiles: make use of new var KERNEL_PATCHVER
replace all occurences of LINUX_VERSION with the cleaner
approach. future kernel upgrades must mostly touch only
one file. the only platform left is netlogic, because it
uses a intermediate kernel 3.14.16

Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>

SVN-Revision: 43047
2014-10-24 19:34:02 +00:00
John Crispin
ddb9bf4bac lantiq xway: generate ramdisk image by default
The installation process on nand-based boards using ubi
like the BTHOMEHUBV2B makes use of a ramdisk image, so it
makes sense to generate this by default.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 42920
2014-10-14 19:01:10 +00:00
John Crispin
0f790247e3 lantiq: allow pcie to be disabled by dts + vgv7519 fix pci irq + disable pcie by dts
Signed-off-by: Eddi De Pieri <eddi@depieri.net>

SVN-Revision: 42907
2014-10-14 11:04:25 +00:00
John Crispin
c085d07ee3 lantiq - vgv7519: load rt5362 eeprom from bootloader param patition
SVN-Revision: 42824
2014-10-06 20:08:30 +00:00
John Crispin
6a961da231 lantiq - vgv7519: enable pci bus
SVN-Revision: 42823
2014-10-06 20:08:18 +00:00
John Crispin
c2e4007bc1 lantiq - vgv7519: remove spi_cs4, since the board use this line for something else
SVN-Revision: 42822
2014-10-06 20:08:11 +00:00
John Crispin
4cdf861521 lantiq - vgv7519: fix open-drain configuration for stp
SVN-Revision: 42821
2014-10-06 20:08:04 +00:00
John Crispin
1e7962ceaf lantiq - vgv7519: add pci-rst entry into dts
SVN-Revision: 42820
2014-10-06 20:07:56 +00:00
John Crispin
ea9aec2fa9 lantiq - vgv7519: remove exin definition copied from dev-board dts
SVN-Revision: 42819
2014-10-06 20:07:45 +00:00
John Crispin
9483a322dd lantiq - vgv7519: we don't have pcie bus so we don't need the reset device tree for this board
SVN-Revision: 42818
2014-10-06 20:07:30 +00:00
John Crispin
48d67fe650 lantiq - vgv7519: we don't have dual minipci-card so we don't need gnt1-req1 for pci handling
SVN-Revision: 42817
2014-10-06 20:07:19 +00:00
John Crispin
d0606948cb lantiq - vgv7519: fix gphy led configuration (this set correct alt function to gpio and let peripherials on pci bus to comes up)
SVN-Revision: 42816
2014-10-06 20:07:04 +00:00
John Crispin
7103d61271 lantiq: fix some alt function on pinctrl-xway
SVN-Revision: 42815
2014-10-06 20:06:51 +00:00
John Crispin
36faa5b145 lantiq: led name has changed from adsl -> dsl
make the notify script aware of this.

https://dev.openwrt.org/ticket/18005

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42798
2014-10-06 05:18:52 +00:00
John Crispin
d731d14362 lantiq: set 3.14 as default
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42618
2014-09-19 10:52:47 +00:00
John Crispin
944820584a Lantiq: fix build warning from dsl_fs script
fix inclusion of functions.sh in dsl_fs init script

without this, the following error is seen during build:
./etc/init.d/dsl_fs: line 4: /lib/functions.sh: No such file or directory

Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>

SVN-Revision: 42575
2014-09-16 14:53:06 +00:00
John Crispin
3dd93e8336 lantiq: move the lantiq,switch property into the interface node
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42574
2014-09-16 14:53:01 +00:00
John Crispin
b520e9b8d4 lantiq: fix switch init on vr9 SoC (3.10)
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42551
2014-09-15 10:19:27 +00:00
John Crispin
32f47538b9 lantiq: fix switch init on vr9 SoC
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42550
2014-09-15 10:19:20 +00:00
John Crispin
f16f310306 lantiq: add default switch setup to td8970
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42544
2014-09-15 10:18:37 +00:00
John Crispin
18b5d72d83 lantiq: update 3.14 patches
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42476
2014-09-11 17:49:57 +00:00
John Crispin
a4eae94a9c lantiq: add ath9k led pin support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42437
2014-09-08 14:29:18 +00:00
John Crispin
4d96ccd87a target: set myself as maintainer
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42335
2014-08-30 09:59:18 +00:00
John Crispin
e47fbcbf1d lantiq: BTHOMEHUBV2B use bigger mtd partition for kernel
The bb-rc3 image for the BTHOMEHUBV2B is too big for its
mtd partition. This patch corrects the partition sizes in
the device tree. This patch should really go in before
bb-final, otherwise the BTHOMEHUBV2B images won't be useable.
I do apologise for not spotting this straight away.

Many thanks,

Ben

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 42316
2014-08-28 06:27:41 +00:00
John Crispin
12b73579e4 lantiq: update to 3.14
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42188
2014-08-18 13:09:30 +00:00
John Crispin
b796ff6ef3 lantiq: generate unique ARV7519RW22 firmware
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 42183
2014-08-18 13:09:11 +00:00
John Crispin
c2668207de lantiq: add support for xrx200 firmware depending on soc type
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 42182
2014-08-18 13:09:08 +00:00
John Crispin
db2e450ab5 lantiq: export soc type
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 42181
2014-08-18 13:08:59 +00:00
John Crispin
5f71dbb005 lantiq: improve ARV7519RW22 support
- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 42180
2014-08-18 13:08:56 +00:00
John Crispin
c21a20cd78 lantiq: fix dgn3500 and td8970 wifi
ath9k failed to come up due to a bad mac addr

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41860
2014-07-28 15:26:41 +00:00
John Crispin
3836d40a8a lantiq: fix dgn3500 ethernet
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41854
2014-07-28 08:06:40 +00:00
John Crispin
ba63338d3f kernel: update to 3.10.49 Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41776
2014-07-20 17:31:11 +00:00
John Crispin
4beb468f11 lantiq: fix board_id/boardname for VGV7519
Signed-off-by: Eddi De Pieri <eddi@depieri.net>

SVN-Revision: 41672
2014-07-16 11:36:02 +00:00
John Crispin
85cacfd753 lantiq: vgv7519 add missing wps label to dts
Signed-off-by: Eddi De Pieri <eddi@depieri.net>

SVN-Revision: 41655
2014-07-14 18:43:02 +00:00
John Crispin
c8bde9da4a lantiq: detect board in preinit state
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41638
2014-07-14 07:38:52 +00:00
Gabor Juhos
d0ad8c00b6 kernel: sort Kconfig options in kernel configs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41614
2014-07-13 16:25:54 +00:00
John Crispin
6134a3de30 target/linux/*: more dead package cleanups
found 2 more

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41574
2014-07-10 20:15:50 +00:00
John Crispin
32e93efc73 target/linux/*: more dead package cleanups
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41571
2014-07-10 20:05:43 +00:00
John Crispin
332b4d556f lantiq: generate /tmp/sysinfo/lantiq_board_name if missing
Run lantiq_board_detect from lantiq_board_name and lantiq_board_model.

This was the one thing missing from r41474 for sysupgrade board
detection to work properly.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 41567
2014-07-10 19:16:43 +00:00
John Crispin
03fef9a2d2 lantiq: enable SysupgradeNAND for BTHOMEHUBV2B
Enables SysupgradeNAND for BTHOMEHUBV2B.

Depends on the following patches:
http://patchwork.openwrt.org/patch/5817/
http://patchwork.openwrt.org/patch/5848/
http://patchwork.openwrt.org/patch/5851/

Many thanks everyone for your help the last couple of days.

Ben

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 41566
2014-07-10 19:16:39 +00:00
John Crispin
4e35eef1d7 lantiq xway: disable gluebi and enable ubiblock
Disables gluebi and enables ubiblock on lantiq xway. Squashfs
images on nand use ubifs instead of jffs2 for the overlay.

I'll leave the equivalent patch for xrx200 to someone who has a
board to test.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 41565
2014-07-10 19:16:35 +00:00
John Crispin
1179d4f924 lantiq: UbinizeImage instead of lantiq-specific ubinize.cfg files
New make target in lantiq to use UbinizeImage and SysupgradeNand.
Only enabled for BTHOMEHUBV2B for the moment but should be useable
for other lantiq nand boards.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 41474
2014-07-02 16:37:23 +00:00
John Crispin
e2915c6981 lantiq: add support for /tmp/sysinfo
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41472
2014-07-02 16:33:11 +00:00
John Crispin
313db9d0ee lantiq: fix missing symbols
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41454
2014-07-02 07:43:32 +00:00
John Crispin
5f31f01853 lantiq: Enable LANTIQ_PHY and LANTIQ_XRX200 only in XRX200 subtarget
Enable LANTIQ_PHY and LANTIQ_XRX200 only in XRX200 subtarget.

These drivers are not needed for ASE, Danube and AR9.
As side effect PHY11G and PHY22F firmwares are not included in the
kernel image, which saves 64 KB.

Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41449
2014-07-01 13:18:38 +00:00
John Crispin
994e5ce2f9 kernel: update 3.10.36->3.10.44
205-fix-headers_install.patch is obseleted by upstream commit 3246a0352e3d58380b9386570f1db1faf7edf8a8

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41351
2014-06-26 13:47:42 +00:00
John Crispin
d219e055be lantiq: remove deprecated jffs2_nand configuration
As far as I am aware, amongst the lantiq boards, jffs2_nand was
only used on the BTHOMEHUBV2B. Ubi-related modifications to the
device tree for that board mean that the resulting jffs2 images
no longer work, and are no longer required anyway. So I suggest
removing the related configuration, which this patch does.

If anyone else is using jffs2_nand on a lantiq target please speak
up!

Incidentally, for a jffs2 rootfs partition concatenated to the
kernel image to be recognised and mounted correctly on nand
this patch or something equivalent is required:
http://patchwork.openwrt.org/patch/5110/
It is marked as accepted in patchwork but doesn't seem to have
been committed. As far as I am concerned it too is deprecated.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 41312
2014-06-24 18:12:52 +00:00
John Crispin
aca708e4e6 lantiq: ubinize autoresize flag for rootfs_data
Setting this flag allows rootfs_data to expand on first boot
to fill remaining free space on nand.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 41310
2014-06-24 18:12:41 +00:00
John Crispin
432f7e52db lantiq: copy rootfs-overlay.ubi to bin/lantiq
At the moment, an rootfs.ubi is copied over to bin/lantiq
but rootfs-overlay.ubi is not. This adds it.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 41270
2014-06-19 14:13:04 +00:00
John Crispin
6c46a10246 lantiq: refresh patches
this adds ben's ath9k fixup

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41269
2014-06-19 14:12:59 +00:00
John Crispin
575127fe1c lantiq: DGN3500 (all known variants) factory and sysupgrade image building support
This patch adds factory image building for the DGN3500, all variants,
and fixes sysupgrade images to make them play nice with the sercomm
secondary boot loader.

The factory images can be used directly in the update dialog in the
interface of the stock firmware and via the special Sercomm bootmode
and a special windows flashing utility (allegedly present in the CD
that came with the device -- but it's also compatible with the NSLU2
Upgrade_207_XP utility.) The special bootmode can be activated by
turning the device on while holding the reset button pressed, then
releasing it when the power led starts blinking red and green. Please
notice that if using the 207 utility, it will always report that the
flashing failed even though it completed successfully. Just power
cycle the router manually after the utility reports the failure and
OpenWRT will boot. This same utility (despite reporting failure in
this case too) can revert a DGN3500 (any variant) to the appropriate
stock Netgear firmware.

This patch is a heavily modified version of a package I found on the
OpenWRT forum with a couple fixes and features added -- mainly the
generation of all the different image variants to support all known
models directly, atm known variants are AnnexA-WW, AnnexA-NA and
AnnexB-DE/GR.

I tested the patch successfully on my device.

Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>

SVN-Revision: 41236
2014-06-17 15:38:54 +00:00
John Crispin
85ca75decd lantiq BTHOMEHUBV2B - update dts for automatic detection of ubi partition and rootfs type
This patches the BTHOMEHUB2B device tree to make use of the
new code for automatic detection of the ubi partition and the
rootfs type within it. Gets rid of the ugly alternative bootargs
lines.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 41214
2014-06-16 18:54:38 +00:00
John Crispin
e6c46554bb lantiq: fixup vgv7519 usb support
https://dev.openwrt.org/ticket/16800

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41213
2014-06-16 18:54:33 +00:00
John Crispin
e9f664c879 kernel: make sure the new UBIBLOCK symbol does not break builds
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41134
2014-06-11 13:00:17 +00:00
John Crispin
ac5d5cbc79 kernel: add a NAND_SUPPORT symbol
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41122
2014-06-11 12:59:22 +00:00
John Crispin
7a03f41940 lantiq: fix eep handling patch
0b79a4a66d17d2c7c12cde8d13637c1b0e5152c2 broke the patch

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41005
2014-06-05 08:19:52 +00:00
John Crispin
f09ac641d6 lantiq: ath5k fix in wifi and ethernet eeprom handling patch.
ath5k fix in wifi and ethernet eeprom handling patch.

Without the line that adds the patch of_ath5k_eeprom_probe cause a
kernel panic, at least with the ARV4518PW.
Tested only in the modem-router mentioned above.

This patch is based in Bruno's hack present in patch #5454.

Signed off by: Bruno Rodríguez <bruno.rodriguez.1980@gmail.com>
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>

SVN-Revision: 40999
2014-06-04 07:20:22 +00:00
John Crispin
fa48c0db1d lantiq: fix up eth_mac and ath_eep support
this patch got messed up by the last rebase

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 40948
2014-06-02 12:45:29 +00:00
John Crispin
7ba5188fe9 lantiq: Fix ARV7510PW22 etop
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 40920
2014-06-02 12:43:43 +00:00
John Crispin
d4ec98c2cc lantiq: Fix ARV4518 etop
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 40919
2014-06-02 12:43:35 +00:00
John Crispin
f933a741a9 target/linux/*/base-files/lib/upgrade/platform.sh - wrong check for ARGC
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:

root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0

Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>

SVN-Revision: 40915
2014-06-02 12:43:22 +00:00