Many changes were done in drivers/pinctrl/bcm/pinctrl-bcm2835.c between
5.4.171 and 5.4.179.
The following 3 patches do not apply any more:
* target/linux/bcm27xx/patches-5.4/950-0316-pinctrl-bcm2835-Add-support-for-BCM2711-pull-up-func.patch
This was already integrated in kernel v5.4-rc1, it was never needed.
* target/linux/bcm27xx/patches-5.4/950-0328-Revert-pinctrl-bcm2835-Pass-irqchip-when-adding-gpio.patch
* target/linux/bcm27xx/patches-5.4/950-0362-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch
I think these were done to fix the problem which was really fixed in
commit 75278f1aff5e ("pinctrl: bcm2835: Change init order for gpio
hogs") from v5.4.175
target/linux/generic/backport-5.4/716-v5.5-net-sfp-move-fwnode-parsing-into-sfp-bus-layer.patch
Move fwnode_device_is_available to the same position as in kernel 5.10.
target/linux/layerscape/patches-5.4/302-dts-0083-arm64-ls1028a-qds-correct-bus-of-rtc.patch
Applied in commit 65816c1034769e714edb70f59a33bc5472d9e55f ("arm64: dts:
ls1028a-qds: move rtc node to the correct i2c bus")
Compile-tested: lantiq/xrx200, bcm27xx/bcm2710
Run-tested: lantiq/xrx200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Removed upstreamed:
target/linux/mvebu/patches-5.4/001-PCI-aardvark-Wait-for-endpoint-to-be-ready-before-tr.patch
target/linux/mvebu/patches-5.4/016-PCI-aardvark-Train-link-immediately-after-enabling-t.patch
target/linux/mvebu/patches-5.4/017-PCI-aardvark-Improve-link-training.patch
target/linux/mvebu/patches-5.4/018-PCI-aardvark-Issue-PERST-via-GPIO.patch
target/linux/mvebu/patches-5.4/020-arm64-dts-marvell-armada-37xx-Set-pcie_reset_pin-to-.patch
The following patch does not apply to upstream any more and needs some
more work to make it work fully again. I am not sure if we are still
able to set the UART to a none standard baud rate.
target/linux/ath79/patches-5.4/921-serial-core-add-support-for-boot-console-with-arbitr.patch
These patches needed manually changes:
target/linux/generic/pending-5.4/110-ehci_hcd_ignore_oc.patch
target/linux/ipq806x/patches-5.4/0065-arm-override-compiler-flags.patch
target/linux/layerscape/patches-5.4/804-crypto-0016-MLKU-114-1-crypto-caam-reduce-page-0-regs-access-to-.patch
target/linux/mvebu/patches-5.4/019-PCI-aardvark-Add-PHY-support.patch
target/linux/octeontx/patches-5.4/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch
All others updated automatically.
Compile-tested on: malta/le, armvirt/64, lantiq/xrx200
Runtime-tested on: malta/le, armvirt/64, lantiq/xrx200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The patch 434-nand-brcmnand-fix-OOB-R-W-with-Hamming-ECC.patch is
integrated in the kernel update 5.4.119 and not needed any more.
Fixes: 9d21eccc6b ("kernel: bump 5.4 to 5.4.119")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_FORTIFY_SOURCE=y is already set in the generic kernel
configuration, but it is not working for MIPS on kernel 5.4, support for
MIPS was only added with kernel 5.5, other architectures like aarch64
support FORTIFY_SOURCE already since some time.
This patch adds support for FORTIFY_SOURCE to MIPS with kernel 5.4,
kernel 5.10 already supports this and needs no changes.
This backports one patch from kernel 5.5 and one fix from 5.8 to make
fortify source also work on our kernel 5.4.
The changes are not compatible with the
306-mips_mem_functions_performance.patch patch which was also removed
with kernel 5.10, probably because of the same problems. I think it is
not needed anyway as the compiler should automatically optimize the
calls to memset(), memcpy() and memmove() even when not explicitly
telling the compiler to use the build in variant.
This increases the size of an uncompressed kernel by less than 1 KB.
Acked-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9ffa2f8193)
The current driver has some troubles:
- Some groupings are wrong.
- The pinctrl group0 owns pins never used (at least in Openwrt) for any
pinmux. The driver hijacks all the pins on the group avoiding any other
use, spite they're free. I.e. for buttons, causing this kernel error:
[ 4.735928] gpio-keys-polled keys: unable to claim gpio 479, err=-22
[ 4.742642] gpio-keys-polled: probe of keys failed with error -22
- Minor errors about groupings on the documentation
- Missing "diag" grouping in dtsi
- Wrong groupings in dtsi
Fix it by setting the correct groups.
And relax the pin capturing, letting the gpios belonging to any group to
be used for other purposes like buttons. This was the behavior with stock
firmwares and old OpenWrt versions which never caused any trouble.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(Cherry-picked from commit 50cb3a750f)
The PCI device ID detected by the wifi drivers on devices using a fallback
SPROM is wrong. Currently the chipnum is used for this parameter.
Most SSB based Broadcom wifi chips are 2.4 and 5GHz capable. But on
devices without a physical SPROM, the only one way to detect if the device
suports both bands or only the 5GHz band, is by reading the device ID from
the fallback SPROM.
In some devices, this may lead to a non working wifi on a 5GHz-only card,
or in the best case a working 2.4GHz-only in a dual band wifi card.
The offset for the deviceid in SSB SPROMs is 0x0008, whereas in BCMA is
0x0060. This is true for any SPROM version.
Override the PCI device ID with the one defined at the fallback SPROM, to
detect the correct wifi card model and allow using the 5GHz band if
supported.
The patch has been tested with the following wifi radios:
BCM43222: b43: both 2.4/5GHz working
brcm-wl: both 2.4/5GHz working
BCM43225: b43: 2.4GHz, working
brcmsmac: working
brcm-wl: it lacks support
BCM43217: b43: 2.4GHz, working
brcmsmac: it lacks support
brcm-wl: it lacks support
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[amend commit description, rework patch to avoid using a new global variable
and keep ssb sprom extraction code as close to ssb/pci.c as possible]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
New upstream changes extract more SPROM values and fix the antenna gain.
These changes can be found in linux drivers/ssb/pci.c.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Calling netdev_reset_queue() from _stop() functions is causing sporadic kernel
panics on bcm63xx, which happen mainly on BCM6318 and BCM6328.
This reverts to the previous behaviour, which called netdev_reset_queue() from
_open() functions.
Tested on Comtrend AR-5315u (BCM6318).
Fixes: 1d6f422e34 ("bcm63xx: sync ethernet driver with net-next")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sync ethernet driver code with upstream Linux kernel:
-Reduce xmit_more code changes.
-Combine rx cleanup code into a function.
-Convert to build_skb.
-Improve rx loop by optimizing loop tracking.
https://lore.kernel.org/netdev/20210106144208.1935-1-liew.s.piaw@gmail.com/
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
[Amend commit description, move patches to the top since they are going to be
upstreamed]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Hamming ECC devices do not cover OOB data, as opposed to BCH ECC devices.
Therefore, disabling ECC for all devices is preventing BCH devices from
correctly reading and writing the OOB data.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Netgear DGND3700v1/DGND3800B shows kernel redundant info at the board
message, already provided by the machine info message.
Use the real board name which is silkscreened on the PCB and used in the
stock firmware header.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Innacomm W3400V6 is an xDSL B/G wireless router based on Broadcom BCM6328 SoC.
Hardware:
SoC: Broadcom BCM6328
CPU: BMIPS4350 V8.0, 320 MHz, 1 core
Flash: SPI-NOR 8MB, MX25L6406E
RAM: 64 MB
Ethernet: 4x 10/100 Mbps
Switch: Integrated
Wireless: 802.11b/g, BCM4312
LEDs/Buttons: 9x / 2x
Flash instruction, web UI:
1) Set a static IP on your computer compatible
with 192.168.1.1, i.e 192.168.1.100
2) Connect the ethernet cable from your computer to the router.
3) Make sure the router is powered off.
4) Press the reset button, don't release it yet!
5) While pressing reset, power on the router.
6) Wait 10 seconds or more.
Note: The power LED is red at first then turns to solid
green when ready.
8) Release the reset button.
9) Browse to 192.168.1.1
10) Select .bin file.
10) Upgrade the image.
11) Wait for it to reboot.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
[Ammend commit description, merge patches, DT improvements]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Technicolor TG582n Telecom Italia branded a.k.a.
Telecom Italia ADSL2+ Wi-Fi N (AGTWI)
has the same PCB as the unbranded Technicolor TG582n with LEDs
connected to different GPIO PINs in active low configuration and
different LED names. It has a PCB similar to the OpenWrt's ADB P.DG A4001N1 one.
Hardware:
* Board ID: DANT-V
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - EtronTech EM68B16CWQD-25H
* Serial flash: 16 Mbyte - Spansion FL 128SAIF00
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30)
* LEDs: 2x Power, 1x ADSL, 2x Internet, 2x Wi-Fi, 2x Service, 4x ethernet
* Buttons: 1x Reset, 1x WPS (named WiFi/LED)
* UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63)
Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
.bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the CFE boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file
PCB: |GPIO: |TG582n: |AGTWI:
LED2R |488(08) |red Power |red Power
LED2G |484(04) |green Power |green Power
LED10R |486(06) | |missing R85 end LED
LED13G |485(05) |green Ethernet |green ADSL
LED11R |494(14) | |red Internet
LED14G |491(11) |green Broadband |green Internet
LED5R |487(07) |red Internet |red Wi-Fi
LED5G |481(01) |green Internet |green Wi-Fi
LED12R |498(18) | |red Service
LED12G |499(19) | |green Service
LED6R |482(02) |red Wi-Fi |missing R108 end LED
LED6G |483(03) |green Wi-Fi |missing R107 end LED
LED7R |490(10) |red WPS |missing R91 end LED
LED7G |489(09) |green WPS |missing R92 end LED
LED4 |508(28) |ethernet port 4 |ethernet port 4
LED3 |507(27) |ethernet port 3 |ethernet port 3
LED9 |506(26) |ethernet port 2 |ethernet port 2
LED8 |505(25) |ethernet port 1 |ethernet port 1
SW3 |503(23) |key Reset |key Reset
SW5 |504(24) |key WPS |key Wi-Fi/LED
SW4 |495(15) |key Wi-Fi |missing R127 end key
SW6 |493(13) | |missing R171 end key
SW1 |492(12) | |missing R1 end key
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[DT fixes, base-files fixes and device variant]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
ADB P.DG A4101N A-000-1A1-AE has a similar PCB as the OpenWrt's ADB P.DG A4001N1
with LEDs connected to different GPIO PINs in active low configuration.
Hardware:
* Board ID: 96328avngv
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - Winbond W9751G6KB-25
* Serial flash: 16 Mbyte - Winbond 25Q128BVFG
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43225 Wireless Network Adapter (rev 23)
* LEDs: 1x Power, 1x DSL, 1x Internet, 4x ETH, 1x USB, 1x WLAN, 1x WPS, 1x TEL
* Buttons: 1x Reset, 1x WPS, 1x unnamed
* UART: 1x TTL 115200n8, VCC RX TX GND, on J502 connector
Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
.bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the cfe boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file
A4101N GPIO LAYOUT:
Power always on
DSL GPIO483(03)
Internet GPIO491(11)
ETH1 GPIO505(25)
ETH2 GPIO506(26)
ETH3 GPIO507(27)
ETH4 GPIO508(28)
USB GPIO490(10)
WLAN controlled by BCM43225
WPS GPIO489(09)
TEL GPIO511(31)
Key RESET GPIO503(23)
Key WPS GPIO504(24)
Key unnamed GPIO492(12)
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[Amend commit description, DTS improvements, refresh patches]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds support for the D-Link DSL-2750u rev C1.
(https://deviwiki.com/wiki/D-Link_DSL-2750U_rev_C1)
It uses the same hardware as ADB P.DG A4001N.
CPU: Broadcom BCM63281 (320 MHz)
RAM: 32M (Winbond W9725G6JB)
Flash: 8M (MXIC MX25L6445E)
Ethernet: 4x 100 Mbps
Wireless: 802.11b/g/n: BCM43225
USB: 1x 2.0
Flash instructions:
1. Assign static IP 192.168.1.100 to PC
2. Unplug the power source
3. Press the RESET button at the router, don't release it yet!
4. Plug the power source.Wait some seconds
5. Release the RESET button
6. Browse to http://192.168.1.1
7. Send the openwrt-bcm63xx-generic-DSL2750U-C1-squashfs-cfe.bin and
wait some minutes until the firmware upgrade finish.
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
[DTS improvements, proper board patch, refresh patches]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
At the moment, bcm63xx creates one patch for each board to add to
board_bcm963xx.c. While this is not really helpful to get an overview
in the first place, it is particularly painful if you want to change
something for an early file and have to refresh all the later patches
accordingly.
Since it does not look like these board patches are upstreamed either,
this commit consolidates all board additions into one patch per "board".
By this, both adding and editing boards should become much simpler,
and we drop about 1300 lines of "code" from patches as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x, lantiq/xrx200 and ath79/generic
Run-tested: ipq806x (R7800), lantiq (Easybox 904 xDSL)
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add test on lantiq]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This PR is a blend of several kernel bumps authored by ldir taken from his
staging tree w/ some further adjustments made by me and update_kernel.sh
Summary:
Deleted upstreamed patches:
generic:
742-v5.5-net-sfp-add-support-for-module-quirks.patch
743-v5.5-net-sfp-add-some-quirks-for-GPON-modules.patch
bcm63xx:
022-v5.8-mtd-rawnand-brcmnand-correctly-verify-erased-pages.patch
024-v5.8-mtd-rawnand-brcmnand-fix-CS0-layout.patch
mediatek:
0402-net-ethernet-mtk_eth_soc-Always-call-mtk_gmac0_rgmii.patch
Deleted patches applied differently upstream:
generic:
641-sch_cake-fix-IP-protocol-handling-in-the-presence-of.patch
Manually merged patches:
generic:
395-v5.8-net-sch_cake-Take-advantage-of-skb-hash-where-appropriate.patch
bcm27xx:
950-0132-lan78xx-Debounce-link-events-to-minimize-poll-storm.patch
layerscape:
701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch
Build system: x86_64
Build-tested: ath79/generic, bcm27xx/bcm2708, bcm27xx/bcm2711,
imx6, mvebu/cortexa9, sunxi/a53
Run-tested: Netgear R7800 (ipq806x)
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-By: Lucian Cristian <Lucian.cristian@gmail.com> [mvebu]
Tested-By: Curtis Deptuck <curtdept@me.com> [x86/64]
[do not remove 395-v5.8-net-sch_cake-Take-advantage-... patch,
adjust and refresh patches, adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-By: John Audia <graysky@archlinux.us> [ipq806x]
This renames board patches to make finding devices easier
and reorders them based on their board.
The devices are grouped based on the board/cpu_id. New device
patches should be numbered based on their group.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This allows better context for board patches and we no longer need a
downstream patch for that.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The patch adding support for the second LED HW blinking interval has been
merged (linux 5.9).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sercomm H500-s is an xDSL dual band wireless router based on Broadcom
BCM63167 SoC.
Hardware:
SoC: Broadcom BCM63167
CPU: BMIPS4350 V8.0, 400 MHz, 2 cores
Flash: NAND 128 MiB
RAM: DDR3 128 MiB
Ethernet: 4x 10/100/1000 Mbps
Switch: BCM53134S
Wireless: 802.11b/g/n: BCM435f (integrated)
802.11ac: Quantenna QT3740BC (onboard SoC)
USB: 1x 2.0
LEDs/Buttons: 11x / 2x
Flash instruction, web UI:
1. Reset to defaults using the reset button if the admin password is
unknown
2. Login into the web UI as admin.
Address: http://192.168.0.1
User: admin
Password: VF-ESVodafone-H-500-s or l033i-h500s
3. Go to Settings -> Firmware Update, and select the Openwrt factory
firmware
4. Update the firmware.
5. Wait until it finish, the device will reboot with Openwrt installed
on the alternative image partitions keeping the stock firmware in
the former.
Notes:
- The patch also adds support for the lowi version. Only the factory
firmware is different.
- The integrated Wifi in the Broadcom Soc isn't still supported.
- The Quantenna 802.11ac wifi works ok, but needs to be configured with
the Quantenna client application. It can't be configured with Luci
nor any iw command since it's a separated subsystem linked via
ethernet.
- The BCM53134S external switch is managed via MDIO which isn't
supported in this target. Therefore it will behave as a dumb switch.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The BCM63167 is a BCM63268 SoC with a different physical packaging.
Add the CPU ID to allow supporting routers with this SoC (i.e Sercomm
H500-s)
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI)
has the same PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected
to different GPIO PINs in active low configuration.
OpenWrt's ADB P.DG A4001N image is made for the ADB P.DG A4001N A-000-1A1-AE.
It has different LEDs configuration and flash size/layout
w.r.t the ADB P.DG A4001N A-000-1A1-AX.
Hardware:
* Board ID: 96328avng
* SoC: Broadcom BCM6328
* RAM DDR2-800: 32 Mbyte - winbond W9725G6KB-25
* Serial flash: 16 Mbyte - MXIC MX25L 12845EMI-10G
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43224/5 Wireless Network Adapter (rev 01)
* LEDs: 2x Power, 2x ADSL, 2x Internet, 2x Wi-Fi, 2x Service
* Buttons: 1x Reset, 1x WPS (named WiFi/LED)
* UART: 1x TTL 115200n8, TX NC RX, on J5 connector (short R192 and R193)
NC GND NC
Installation via CFE:
* Stock CFE has to be overwriten with one for 96328avng boards that can upload
.bin images with no signature check (cfe-A4001N-V0000_96328avng.bin)
* connect a serial port to the board
* Stop the boot process after power on by pressing enter
* set static IP 192.168.1.2 and subnet mask 255.255.255.0
* navigate to http://192.168.1.1/
* upload the OpenWrt image file
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
There are older devices which require overriding the RGMII ports, so this
shouldn't be limited and forced to BCM63268.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
