Commit Graph

124 Commits

Author SHA1 Message Date
Davide Fioravanti
bb505d82ad ramips: add support for Wavlink WL-WN531A3
The Wavlink WL-WN531A3 is an AC1200 router with 5 fast ethernet ports
and one USB 2.0 port.
It's also known as Wavlink QUANTUM D4.

Hardware
--------
SoC:   Mediatek MT7628AN
RAM:   64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CSIG3)
ETH:
  - 5x 10/100 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
  - 2.4GHz: 1x (integrated in SOC) (2x2:2)
  - 5GHz:   1x MT7612E (2x2:2)
  - 4 external antennas
BTN:
  - 1x Reset button
  - 1x WPS button
  - 1x Turbo button
  - 1x Touchlink button
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
  - 1x USB 2.0 port
UART:
  - 57600-8-N-1
    J1
      O VCC +3,3V (near lan ports)
      o RX
      o TX
      o GND

Everything works correctly.

Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.

Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on M31A3.V4300.200420 firmware version.

1) Go to http://192.168.10.1/webcmd.shtml

2) Type the following line in the "Command" input box and then press enter:
	mkdir /etc_ro/lighttpd/www/dev; cp /dev/mtd0ro /etc_ro/lighttpd/www/dev/mtd0ro; ls -la /etc_ro/lighttpd/www/dev/mtd0ro

3) After few seconds in the textarea should appear this output:
	-rw-r--r--    1 0        0         8388608 /etc_ro/lighttpd/www/dev/mtd0ro

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
   content of the whole NOR. If the file size is 0 byte, stop reading
   and ask for help in the forum.

5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
	rm /etc_ro/lighttpd/www/dev/mtd0ro; for i in 1 2 3 4 ; do cp /dev/mtd${i}ro /etc_ro/lighttpd/www/dev/mtd${i}ro; done; ls -la /etc_ro/lighttpd/www/dev/

6) After few seconds, in the textarea should appear this output:
	-rw-r--r--    1 0        0          196608 mtd1ro
	-rw-r--r--    1 0        0           65536 mtd2ro
	-rw-r--r--    1 0        0           65536 mtd3ro
	-rw-r--r--    1 0        0         8060928 mtd4ro
	drwxr-xr-x    7 0        0               0 ..
	drwxr-xr-x    2 0        0               0 .

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

7) Open the following links to download the partitions of the OEM FW:
	http://192.168.10.1/dev/mtd1ro
	http://192.168.10.1/dev/mtd2ro
	http://192.168.10.1/dev/mtd3ro
	http://192.168.10.1/dev/mtd4ro

   If one (or more) of these files are 0 byte, stop reading and ask
   for help in the forum.

8) Store these downloaded files in a safe place.

9) Reboot your router to remove any temporary file in ram.

Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.

Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) Router mac addresses:
   LAN		XX:XX:XX:XX:XX:9B (factory @ 0x28)
   WAN		XX:XX:XX:XX:XX:9C (factory @ 0x2e)
   WIFI 2G	XX:XX:XX:XX:XX:9D (factory @ 0x04)
   WIFI 5G	XX:XX:XX:XX:XX:9E (factory @ 0x8004)

   LABEL	XX:XX:XX:XX:XX:9D

2) There is just one wifi led for both wifi interfaces.
   It currently shows only the 2.4 GHz wifi activity.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2022-04-16 14:02:11 +02:00
Ray Wang
3c4810fecc ramips: add support for Asus RT-AC1200
Asus RT-AC1200 is a 2.4/5GHz dual band AC router,
based on MediaTek MT7628AN.

Specification:
* SoC: MT7628AN
* RAM: DDR2 64 MiB
* Flash: 16 MiB NOR (W25Q128BV)
* Wi-Fi:
  * 2.4GHz: SoC Built-in
  * 5GHz: MT7612EN
* Ethernet: 5x 100Mbps
  * Switch: SoC built-in
* USB: 1x 2.0

Flash Layout:
 0x0000000-0x0030000 : "bootloader"
 0x0030000-0x0040000 : "nvram"
 0x0040000-0x0050000 : "factory"
 0x0050000-0x1000000 : "firmware"

MAC address:
 LAN: factory 0x28
 WAN: factory 0x22
 2.4G: factory 0x4
 5G: factory 0x8004

Installation via **recovery** mode:
1. Download the Asus recovery firmware (windows) tool from
   http://dlcdnet.asus.com/pub/ASUS/LiveUpdate/Release/Wireless/Rescue.zip
2. Set your ethernet IP manually 192.168.1.5 / 255.255.255.0 with NO
   gateway.
3. Plug in your ethernet to LAN port 1 on the router.
4. Load up the recovery software with the firmware file, but don't press
   "Upload" yet.
5. Plug in the router to power WHILE HOLDING the reset button in. While
   CONTINUING to hold the button, select "Upload" Continue to hold the
   reset button in until it finishes and verifies!
6. If that doesn't work try pressing "Upload" first just before you do
   step 5. At some point while holding reset the rescue tool will finally
   detect and upload the firmware. That's when you can let go of the
   reset button.
7. The router will reboot and not much will happen. Wait a minute or 2.
8. Power off and on the router again. Voila. Set everything your Ethernet
   IP back to DHCP (automatically) and you're good to go.

Revert to stock firmware:
1. Install stock image via recovery mode.

Tested-by: Ivan Pavlov <AuthorReflex@gmail.com>
Signed-off-by: Ray Wang <raywang777@foxmail.com>
2022-03-09 15:38:28 +09:00
INAGAKI Hiroshi
f7f9e6bd20 ramips: use parser_trx for Buffalo WCR-1166DS
Buffalo WCR-1166DS uses trx-fomatted firmware and the custom magic
number (0x5C436F74, "\Cot") is required for OpenWrt installation from
OEM WebUI.
But the current mtdsplit_trx doesn't support the custom magic number and
fail to parse and split to kernel and rootfs when the factory image is
flashed. Then, the kernel fails to mount rootfs automatically and panics.

Before the commit fddc78bc11, mtdsplit_trx
was patched in ramips target and the device-specific magic number was
supported only for WCR-1166DS[1].
But the patch was not inherited to the later version of the kernel and
deleted by the above commit, then, the custom magic number support was
broken.

[1]: 05d6e92594/target/linux/ramips/patches-4.4/0400-mtd-mtdsplit-add-support-for-custom-trx-magic-for-Buffalo-WCR-1166DS.patch (L27)

log (factory image):

[    1.165312] spi-mt7621 10000b00.spi: sys_freq: 193333333
[    1.195782] spi-nor spi0.0: w25q128 (16384 Kbytes)
[    1.205353] 7 fixed-partitions partitions found on MTD device spi0.0
[    1.217938] Creating 7 MTD partitions on "spi0.0":
[    1.227436] 0x000000000000-0x000000030000 : "u-boot"
[    1.238427] 0x000000030000-0x000000040000 : "u-boot-env"
[    1.250123] 0x000000040000-0x000000050000 : "factory"
[    1.261306] 0x000000050000-0x000000810000 : "firmware"
[    1.282051] 0x000000810000-0x000000fd0000 : "firmware2"
[    1.293594] 0x000000fd0000-0x000000fe0000 : "glbcfg"
[    1.304719] 0x000000fe0000-0x000000ff0000 : "board_data"
...
[    1.452424] /dev/root: Can't open blockdev
[    1.460619] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    1.475434] Please append a correct "root=" boot option; here are the available partitions:
[    1.491986] 1f00             192 mtdblock0
[    1.491989]  (driver?)
[    1.504938] 1f01              64 mtdblock1
[    1.504941]  (driver?)
[    1.517885] 1f02              64 mtdblock2
[    1.517888]  (driver?)
[    1.530831] 1f03            7936 mtdblock3
[    1.530834]  (driver?)
[    1.543777] 1f04            7936 mtdblock4
[    1.543781]  (driver?)
[    1.556724] 1f05              64 mtdblock5
[    1.556727]  (driver?)
[    1.569672] 1f06              64 mtdblock6
[    1.569675]  (driver?)
[    1.582617] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    1.598976] Rebooting in 1 seconds..

This patch fixes this issue by using parser_trx with specifying custom
magic number in dts instead of mtdsplit_trx.

log (fixed factory image):

[    1.202044] spi-mt7621 10000b00.spi: sys_freq: 193333333
[    1.225369] spi-nor spi0.0: w25q128 (16384 Kbytes)
[    1.235015] 7 fixed-partitions partitions found on MTD device spi0.0
[    1.247603] Creating 7 MTD partitions on "spi0.0":
[    1.257106] 0x000000000000-0x000000030000 : "u-boot"
[    1.269447] 0x000000030000-0x000000040000 : "u-boot-env"
[    1.281192] 0x000000040000-0x000000050000 : "factory"
[    1.294208] 0x000000050000-0x000000810000 : "firmware"
[    1.305774] 2 trx partitions found on MTD device firmware
[    1.316540] Creating 2 MTD partitions on "firmware":
[    1.326399] 0x00000000001c-0x000000214754 : "linux"
[    1.336063] mtd: partition "linux" doesn't start on an erase/write block boundary -- force read-only
[    1.357070] 0x000000214754-0x0000007c0000 : "rootfs"
[    1.366994] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
[    1.386368] mtd: device 5 (rootfs) set to be root filesystem
[    1.398700] 1 squashfs-split partitions found on MTD device rootfs
[    1.411027] 0x000000520000-0x0000007c0000 : "rootfs_data"
[    1.422841] 0x000000810000-0x000000fd0000 : "firmware2"
[    1.436282] 0x000000fd0000-0x000000fe0000 : "glbcfg"
[    1.447408] 0x000000fe0000-0x000000ff0000 : "board_data"
...
[    1.611216] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-03-06 20:40:35 +01:00
Rodrigo Araujo
7c8ade1765 ramips: correct vendor name for COMFAST/Joowin
When Joowin WR758AC V1 and V2 devices were added, they should have been
added with the primary manufacturer name which is COMFAST, since Joowin
is just an alternate vendor name on some coutries or stores.

Fix this by changing the the vendor name on the respective files and set
Joowin as ALT0 variants while ensuring compatibility for early users.
Also adjust the model names to better follow the naming rules.

As a side effect, fix mt76x8 network script which was left incorrectly
unsorted on the case block conditions.

Fixes: 766733e172 ("ramips: add support for Joowin WR758AC V1 and V2")
Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
2022-01-22 01:17:04 +01:00
Rodrigo Araujo
766733e172 ramips: add support for Joowin WR758AC V1 and V2
This commit adds support for Joowin (aka Comfast) WR758AC V1 and V2
devices.

Both have the same wall AP/repeater form factor and differ only
in the 5Ghz chipset (V1 has MT7662, V2 has MT7663).

OpenWrt developers forum page:
https://forum.openwrt.org/t/87355

Specifications:

 - CPU: MediaTek MT7628AN (580MHz)
 - Flash: 8MB
 - RAM: 64MB DDR2
 - 2.4 GHz: 802.11b/g/n (MT7603)
 - 5 GHz: 802.11ac (V1 has MT7662, V2 has MT7663)
 - Antennas: 4x external single band antennas
 - LAN: 1x 10/100M
 - LED: Wifi 3x blue. Programmable
 - Button: WPS

MAC addresses as verified by OEM firmware:

use address source
LAN *:83 factory 0xe000
2g *:85 factory 0x4
5g *:86 factory 0x8004

How to install:
1- Setup a TFTP server on a machine with IP address 192.168.1.10/24
2- Name the image as `firmware_auto.bin` and place it on the root of the
TFTP server
3- Connect the device via Ethernet, it should pick and flash the image

Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
2022-01-08 00:49:59 +01:00
Thomas Aldrian
b28443f82e ramips: add support for Wavlink WL-WN576A2
This commit adds support for the Wavlink WL-WN576A2 wall-plug wireles
repeater / router. It is also sold under the name SilverCrest SWV 733 B1.

Device specs:

- CPU: MediaTek MT7628AN
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 1x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- 5 GHz: a/n/ac MT7610EN
- Buttons: WPS, reset, sliding switch (ap/repeater)
- LEDs: 5x wifi status, 1x LAN/WAN, 1x WPS

Flashing:

U-Boot launches a TFTP client if WPS button is held during boot.

- Server IP: 192.168.10.100
- Firmware file name: firmware.bin

Device will reboot automatically. First boot takes about 90s.

Coelner (waenger@gmail.com) is the original author, but I have made some
fixes. He does not wish to sign off using his real name.

Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
2021-11-20 21:08:25 +01:00
Eduardo Santos
3c97fb4346 ramips: add support for Xiaomi MiWifi 3C
This commit adds support for Xiaomi MiWiFi 3C device.

Xiaomi MiWifi 3C has almost the same system architecture
as the Xiaomi Mi WiFi Nano, which is already officially
supported by OpenWrt.

The differences are:

 - Numbers of antennas (4 instead of 2). The antenna management
   is done via the µC. There is no configuration needed in the
   software code.
 - LAN port assignments are different. LAN1 and WAN are
   interchanged.

OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c

OpenWrt developers forum page:
https://forum.openwrt.org/t/support-for-xiaomi-mi-3c

Specifications:

 - CPU: MediaTek MT7628AN (575MHz)
 - Flash: 16MB
 - RAM: 64MB DDR2
 - 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
 - Antennas: 4x external single band antennas
 - WAN: 1x 10/100M
 - LAN: 2x 10/100M
 - LED: 1x amber/blue/red. Programmable
 - Button: Reset

MAC addresses as verified by OEM firmware:

use address source
LAN *:92 factory 0x28
WAN *:92 factory 0x28
2g *:93 factory 0x4

OEM firmware uses VLAN's to create the network interface for WAN and LAN.

Bootloader info:
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader start OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".

How to install:
1- Use OpenWRTInvasion to gain telnet, ssh and ftp access.
   https://github.com/acecilia/OpenWRTInvasion
   (IP: 192.168.31.1 - Username: root - Password: root)
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command  "dd if=/dev/mtd0 of=/tmp/mtd0".
   Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin
   to /tmp in router using ftp.
5- Enable UART access and change start image for OS1.
```
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
```
6- Installing Openwrt on OS1 and free OS2.
```
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1
```

Limitations: For the first install the image size needs to be less
than 7733248 bits.

Thanks for all community and especially for this device:
minax007, earth08, S.Farid

Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com>
[wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to
 &wmac, convert to nvmem]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-31 21:24:47 +01:00
Michal Kozuch
c12ef2f760 ramips: add support for TP-Link RE305 v3
Specs (same as in v1):
- MT7628AN (575 MHz)
- 64MB RAM
- 8MB of flash (SPI NOR)
- 1x 10/100Mbps Ethernet (MT7628AN built-in switch with vlan)
- 1x 2.4GHz wifi (MT7628AN)
- 1x 5Ghz wifi (MT7612E)
- 4x LEDs (5 GPIO-controlled)
- 1x reset button
- 1x WPS button

The only and important difference between v1 & v3 is in flash memory
layout, so pls don't interchange these 2 builds!

Installation through web-ui (on OEM factory firmware):
1. Visit http://tplinkrepeater.net or the configured IP address of
   your RE305 v3 (default 192.168.0.254).
2. Log in with the password you've set during initial setup of the
   RE305 (there is no default password).
3. Go to Settings -> System Tools -> Firmware upgrade
4. Click Browse and select the OpenWRT image with factory.bin suffix
   (not sysupgrade.bin)
5. A window with a progress bar will appear. Wait until it completes.
6. The RE305 will reboot into OpenWRT and serve DHCP requests on the
   ethernet port.
7. Connect an RJ45 cable from the RE305 to your computer and access
   LuCI at http://192.168.1.1/ to configure (or use ssh).

Disassembly:
Just unscrew 4 screws in the corners & take off the back cover.
Serial is exposed to the right side of the main board (in the middle)
and marked with TX/RX/3V3/GND, but the holes are filled with solder.

Installation through serial:
1. connect trough serial (1n8, baudrate=57600)
2. setup the TFTP server and connect it via ethernet
   (ipaddr=192.168.0.254 of device, serverip=192.168.0.184 - your pc)
3. boot from a initramfs image first (choose 1 in the bootloader
   options)
4. test it a bit with that, then proceed to run sysupgrade build

MAC addresses as verified by OEM firmware:

  use  OpenWrt  address  reference
  LAN  eth0     *:d2     label
  2g   wlan0    *:d1     label - 1
  5g   wlan1    *:d0     label - 2

  The label MAC address can be found in config 0x2008.

Signed-off-by: Michal Kozuch <servitkar@gmail.com>
[redistribute WLAN node properties between DTS/DTSI, remove
 compatible on DTSI, fix indent/wrapping, split out firmware-utils
 change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-30 22:05:25 +02:00
Giovanni Cascione
d57ba86e48 ramips: add support for D-Link DAP-1325-A1
This patch adds support for D-Link DAP-1325-A1 (Range Extender Wi-Fi N300)

Specifications:
- SoC: 580Mhz MT7628NN
- RAM: 64MB, DDR2 SDRAM
- Storage: 8MB, SPI (W25Q64JVSSIQ)
- Ethernet: 1x 10/100 LAN port
- WIFI: 2.4 GHz 802.11bgn
- LED: Status (2x to provide 3 colors), Wi-Fi Signal Strength (4x)
- Buttons: Reset, WPS
- UART: Serial console (57600, 8n1)
Row of 4 holes near LAN port, starting from square hole:
3.3V, TX,RX,GND
- FCC ID: fccid.io/KA2AP1325A1/

Installation:

Failsafe UI
Firmware can be uploaded with Failsafe UI web page:
- turn device off
- press and hold reset button
- turn device on
- keep holding reset until red wifi strength led turns on (ab. 10sec)
- connect to device through LAN port
PC must be configured with static ip (192.168.0.x)
- connect to 192.168.0.50
- select image to be flashed and upload.
Device will reboot after successful update

Serial port/TFTP server
- Connect through serial connectors on PCB (e.g. with teraterm)
- Set up a TFTP server, and connect through LAN with static IP
- Put image file in the root of the server
- Boot the device and select '2' at U-Boot startup
- Set device IP, server IP and image file name
- Start upload and flash

Signed-off-by: Giovanni Cascione <ing.cascione@gmail.com>
[fix whitespaces in DTS, convert to nvmem, add mtd-eeprom]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-25 01:42:17 +02:00
Shiji Yang
09143282bd ramips: add support for Motorola MWR03
Specifications:
* SOC: MT7628AN + MT7612E
* ROM: 8 MiB Flash
* RAM: 64 MiB DDR2
* WAN: 10/100M *1
* LAN: 10/100M *3
* Button: Reset *1
* LEDs: orange *1, white *1
* Antennas: 2.4 GHz *2 + 5 GHz *2
* TTL Baudrate: 57600
* TFTP Upgrade: IP: 192.168.51.1, Server: 192.168.51.100

MAC addresses as verified by OEM firmware:

use   address   source
2g    *:d8      factory 0x0004 (label)
5g    *:d9      factory 0x8004
LAN   *:d7      factory $label -1
WAN   *:da      factory $label +2

Installation (TFTP + U-Boot):
 * Connect device with a TTL cable and open a serial session by
   PuTTY.
 * Press "2" when booting to select "Load system code then write
   to Flash via TFTP".
 * Configure the IP of local host server.
 * Upload firmware by tftpd64, it will boot when write instruction
   is executed.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix DTS line endings, fix label MAC address, adjust status LED
 names, convert mtd-mac-address-increment to mac-address-increment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-25 01:41:35 +02:00
Alexander Couzens
0fac6f5562
ramips: minew g1-c: add the old device name to the supported devices
Allow to use the sysupgrade image as factory image without
additional force.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2021-07-07 18:32:14 +02:00
Alexander Couzens
8d497b6570
ramips: add support for minew g1-c
The minew g1-c is a smart home gateway / BLE gateway.
A Nordic nRF52832 is available via USB UART (cp210x) to support BLE.
The LED ring is a ring of 24x ws2812b connect to a generic GPIO (unsupported).
There is a small LED which is only visible when the device is open which
will be used as LED until the ws2812b is supported.
The board has also a micro sdcard/tfcard slot (untested).
The Nordic nRF52832 exposes SWD over a 5pin header (GND, VCC, SWD, SWC, RST).
The vendor uses an older OpenWrt version, sysupgrade can be used via
serial or ssh.

CPU:		MT7628AN / 580MHz
RAM:		DDR2 128 MiB RAM
Flash:		SPI NOR 16 MiB W25Q128
Ethernet:	1x 100 mbit (Port 0) (PoE in)
USB:		USB hub, 2x external, 1x internal to USB UART
Power:		via micro usb or PoE 802.11af
UART:		3.3V, 115200 8n1

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2021-07-05 17:27:13 +02:00
Thomas Aldrian
f755d81999 ramips: add support for Wavlink WL-WN578A2
This commit adds support for the Wavlink WL-WN578A2 dual-band wall-plug
wireless router. This device is also sold under the name SilverCrest
SWV 733 A2.

Device Specifications:

- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: WPS/Power, LAN, WAN, wifi-low, wifi-med, wifi-high
- Buttons: Reset, WPS
- Sliding mode switch: AP, repeater, client
- Small sliding power switch

Flashing instructions:

U-Boot launches TFTP client if WPS button is pressed during power-on.
Configure as follows:

- Server IP: 192.168.10.100
- Filename (rename sysupgrade file to this): firmware.bin

Flashing should not take more than a minute, device will reboot
automatically.

Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
2021-05-28 01:12:21 +02:00
Piotr Dymacz
cf3f1f82ea ramips: fix SUPPORTED_DEVICES for ALFA Network devices
Vendor firmware expects model name without manufacturer name inside
'supported_devices' part of metadata. This allows direct upgrade to
OpenWrt from vendor's GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-05-16 23:59:13 +02:00
Adrian Schmutzler
9397b22df1 treewide: make AddDepends/usb-serial selective
Make packages depending on usb-serial selective, so we do not have
to add kmod-usb-serial manually for every device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 12:38:38 +01:00
INAGAKI Hiroshi
08768b44d9 ramips: add support for ELECOM WRC-1167FS
ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on
MT7628AN.

Specification:

- SoC		: MediaTek MT7628AN
- RAM		: DDR2 64 MiB (NT5TU32M16FG-AC)
- Flash		: SPI-NOR 16 MiB (W25Q128JVSIQ)
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: MediaTek MT7628AN (SoC)
  - 5 GHz	: MediaTek MT7612E
- Ethernet	: 10/100 Mbps x2
  - Switch	: MT7628AN (SoC)
- LEDs/Keys	: 6x, 3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J1: 3.3V, GND, TX, RX from "J1" marking
  - 57600n8
- Power		: 12 VDC, 1 A

Flash instruction using factory image:

1. Boot WRC-1167FS normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button to
   perform firmware update
4. Wait ~120 seconds to complete flashing

Notes:

- Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware

- Additional padding in factory image is required to avoid incomplete
  flashing on stock firmware

MAC addresses:

- LAN	: BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28   (hex))
- WAN	: BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22   (hex))
- 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac    (text) / Factory, 0x4    (hex))
- 5GHz	: BC:5C:4C:xx:xx:6B (Config, rmac2   (text) / Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-02-11 16:37:53 +01:00
Ewan Parker
ddafcc7947 ramips: add support for Hi-Link HLK-7688A
Specifications:

  - SoC: MediaTek MT7688AN
  - RAM: 128 MB
  - Flash: 32 MB
  - Ethernet: 5x 10/100 (1x WAN, 4x LAN)
  - Wireless: built in 2.4GHz (bgn)
  - USB: 1x USB 2.0 port
  - Buttons: 1x Reset
  - LEDs: 1x (WiFi)

Flash instructions:

  - Configure TFTP server with IP address 10.10.10.3
  - Name the firmware file as firmware.bin
  - Connect any Ethernet port to the TFTP server's LAN
  - Choose option 2 in U-Boot
  - Alternatively choose option 7 to upload firmware to the built-in
    web server

MAC addresses as verified by OEM firmware:

  use   address   source
  2g    *:XX      factory 0x4
  LAN   *:XX+1    factory 0x28
  WAN   *:XX+1    factory 0x2e

Notes:

This board is ostensibly a module containing the MediaTek MT7688AN SoC,
128 MB DDR2 SDRAM and 32 MB flash storage.  The SoC can be operated in
IoT Gateway Mode or IoT Device Mode.

From some vendors the U-Boot that comes installed operates on UART 2
which is inaccessible in gateway mode and operates unreliably in the
Linux kernel when using more than 64 MB of RAM.  For those, updating
U-Boot is recommended.

Signed-off-by: Ewan Parker <ewan@ewan.cc>
[add WLAN to 01_leds]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 14:54:47 +01:00
Adrian Schmutzler
6d4382711a ramips: use full names for Xiaomi Mi Router devices
This aligns the device/image names of the older Xiaomi Mi Router
devices with their "friendly" model and DEVICE_MODEL properties.

This also reintroduces consistency with the newer devices already
following that scheme.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-12-08 17:18:57 +01:00
Ataberk Özen
4287f73989 ramips: add support for Xiaomi Mi Router 4C
This commit adds support for Xiaomi's Mi Router 4C device.

Specifications:

- CPU: MediaTek MT7628AN (580MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LEDs: 2x yellow/blue. Programmable (labelled as power on case)
                      - Non-programmable (shows WAN activity)
- Button: Reset

How to install:

1- Use OpenWRTInvasion to gain telnet and ftp access.
2- Push openwrt firmware to /tmp/ using ftp.
3- Connect to router using telnet. (IP: 192.168.31.1 -
   Username: root - No password)
4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into
   the router..
5- It takes around 2 minutes. After that router will restart itself
   to OpenWrt.

Signed-off-by: Ataberk Özen <ataberkozen123@gmail.com>
[wrap commit message, bump PKG_RELEASE for uboot-envtools, remove
dts-v1 from DTS, fix LED labels]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-25 19:34:13 +01:00
Filip Moc
b641eb6ecf ramips: add support for TP-Link MR6400 v5
TL-MR6400v5 is very similar to TL-MR6400v4. Main differences are:
  - smaller form factor
  - different LED GPIOs
  - different switch connections

You can flash via tftp recovery:
 - serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24
 - connect to any ethernet port
 - power on the device while holding the reset button
 - wait at least 8 seconds before releasing reset button

Flashing via OEM web interface does not work.

LTE module does not support DHCP so it must be configured via QMI.

Hardware Specification (v5.0 EU):
 - SoC: MT7628NN
 - Flash: Winbond W25Q64JVS (8MiB)
 - RAM: ESMT M14D5121632A (64MiB)
 - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
 - Ethernet: 1NIC (4x100M)
 - WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
 - Power: DC 9V 0.85A

Signed-off-by: Filip Moc <lede@moc6.cz>
2020-11-25 13:23:06 +01:00
Filip Moc
0d65177658 ramips: add support for TP-Link MR6400 v4
You can flash via tftp recovery:
 - serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24
 - connect to any ethernet port
 - power on the device while holding the reset button
 - wait at least 8 seconds before releasing reset button

Flashing via OEM web interface does not work.

LTE module does not support DHCP so it must be configured via QMI.

Hardware Specification (v4.0 EU):
 - SoC: MT7628NN
 - Flash: Winbond W25Q64JVS (8MiB)
 - RAM: ESMT M14D5121632A (64MiB)
 - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
 - Ethernet: 1NIC (4x100M)
 - WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
 - Power: DC 9V 0.85A

Signed-off-by: Filip Moc <lede@moc6.cz>
2020-11-23 00:46:40 +00:00
Marc Egerton
f276395cda ramips: add support for the Hak5 WiFi Pineapple Mark 7
This patch adds support for the WiFi Pineapple Mark 7, a wireless
penetration testing tool.

Specifications:
    * SoC: MediaTek MT7628 (580MHz)
    * RAM: 256MiB (DDR2)
    * Storage 1: 32MiB NOR (SPI)
    * Storage 2: 2GB eMMC
    * Wireless 1: 802.11b/g/n 2.4GHz (Built In)
    * Wireless 2: 802.11b/g/n 2.4GHz (MT7601)
    * Wireless 3: 802.11b/g/n 2.4GHz (MT7601)
    * USB: 1x USB Type-A 2.0 Host Port
    * Ethernet: 1x USB Type-C AX88772C Ethernet
    * UART: 57600 8N1 on PCB
    * Inputs: 1x Reset Button
    * Outputs: 1x RGB LED
    * FCCID: 2AA52MK7

Flash Instructions:
    Original firmware is based on OpenWRT.
    Use sysupgrade via SSH to flash.

Signed-off-by: Marc Egerton <foxtrot@realloc.me>
[pepe2k@gmail.com: set only required/used gpio groups to gpio function]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-11-18 23:49:34 +01:00
Richard Fröhning
33b76d66d1 ramips: add support for TP-Link RE200 v4
TP-Link RE200 v4 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas.
It's based on MediaTek MT7628AN+MT7610EN like the v2/v3.

Specifications
--------------

- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button
- UART connection holes on PCB (57600 8n1)

There are 2.4G and 5G LEDs in red and green which are controlled
separately.

MAC addresses
-------------

The MAC address assignment matches stock firmware, i.e.:

LAN : *:8E
2.4G: *:8D
5G  : *:8C

MAC address assignment has been done according to the RE200 v2.

The label MAC address matches the OpenWrt ethernet address.

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Recovery
--------

Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.

Instructions for serial console and recovery may be checked out in
commit 6d6f36ae78 ("ramips: add support for TP-Link RE200 v2") or on
the device's Wiki page.

Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[removed empty line, fix commit message formatting]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-10-20 03:01:13 +02:00
Adrian Schmutzler
4527f59428 ramips: move ravpower-wd009-factory recipe to mt76x8.mk
The recipe is only used for a single device, so put it in the
subtarget file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-11 18:40:44 +02:00
Andrew Freeman
ff5dd32164 ramips: add support for TP-Link TL-WR850N v2
This patch adds support for the TP-Link TL-WR850N v2. This device
is very similar to TP-Link TL-WR840 v4 and TP-Link TL-WR841 v13.

Specifications:
SOC: MediaTek MT7628NN
Flash: 8 MiB SPI
RAM: 64 MiB
WLAN: MediaTek MT7628NN
Ethernet: 5 ports (100M)

Installation Using the integrated tftp capability of the router:
1. Turn off the router.
2. Connect pc to one of the router LAN ports.
3. Set your PC IPv4 address to 192.168.0.66/24.
4. Run any TFTP server on the PC.
5. Put the recovery firmware on the root directory of TFTP server
   and name the file tp_recovery.bin
6. Start the router by pressing power button while holding the
   WPS/Reset button (or both WPS/Reset and WIFI buttons)
7. Router connects to your PC with IPv4 address 192.168.0.2,
   downloads the firmware, installs it and reboots. LEDs are
   flashing. Now you have OpenWrt installed.
8. Change your IPv4 PC address to something in 192.168.1.0/24
   network or use DHCP to get an address from your OpenWrt router.
9. Done! You can login to your router via ssh.

Forum link:
https://forum.openwrt.org/t/add-support-for-tp-link-tl-wr850n-v2/66899

Signed-off-by: Andrew Freeman <labz56@gmail.com>
[squash an tidy up commits, sort nodes]
Signed-off-by: Darsh Patel <darshkpatel@gmail.com>
[minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-27 16:36:18 +02:00
Adrian Schmutzler
3b89849b57 ramips: add common definition netgear_sercomm_nor
Like NAND-based devices, SPI-NOR based Netgear devices also share
a common setup for their images. This creates a common defition
for them in image/Makefile, so it can be reused across subtargets.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 16:56:06 +02:00
Tobias Welz
816973f42a ramips: enable flashing WizFi630S via OEM firmware
WIZnet WizFi630s board name is written slightly different it its OEM
OpenWrt firmware. This causes an incompatibility warning during flashing
with sysupgrade. This patch is adding the vendor board name to the
supported devices list to avoid this warning. For initial flashing you
can use sysupgrade via command line or luci beside of TFTP.
Do not keep the OEM configuration during sysupgrade.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
2020-08-05 23:08:03 +02:00
Richard Fröhning
009e62c92c ramips: add support for TP-Link RE200 v3
TP-Link RE200 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2.

Specifications
--------------

- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button

Unverified:
- UART header on PCB (57600 8n1)

There are 2.4G and 5G LEDs in red and green which are controlled
separately.

MAC addresses
-------------

MAC address assignment has been done according to the RE200 v2.

The label MAC address matches the OpenWrt ethernet address.

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Recovery
--------

Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.

The device has not been opened for adding support. However, it is expected
that the behavior is similar to the RE200 v2. Instructions for serial console
and recovery may be checked out in commit 6d6f36ae78 ("ramips: add support
for TP-Link RE200 v2") or on the device's Wiki page.

Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[adjust commit title/message, sort support list]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 23:34:34 +02:00
Adrian Schmutzler
1deaf695ec ramips: fix/tidy up 4M tplink-v2-image flash layouts
For the TP-Link 4M devices with tplink-v2-image recipe
(mktplinkfw2.c), there are two different flash layouts based
on the size of the (u)boot partition:

device         uboot    OEM firmware  OpenWrt (incl. config)
tl-wr840n-v5   0x20000  0x3c0000      0x3d0000
tl-wr841n-v14  0x10000  0x3d0000      0x3e0000

In both cases, the 0x10000 config partition is used for the firmware
partition as well due to the limited space available and since it's
recreated by the OEM firmware anyway.

However, the TFTP flashing process will only copy data up to the
size of the initial (OEM) firmware size. Therefore, while we can
use the bigger partition to have additional erase blocks on the
device, we have to limit the image sizes to the TFTP limits.

So far, only one layout definition has been set up in mktplinkfw2.c
for 4M mediatek devices. This adds a second one and assigns them
to the devices so the image sizes are correctly restrained.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 12:17:08 +02:00
Robinson Wu
84cb0f7ace ramips: add support for JS76x8 series DEV boards
This commit adds support for the Jotale JS76x8 series development boards.
These devices have the following specifications:

- SOC: MT7628AN/NN, MT7688AN, MT7628DAN
- RAM of MT7628AN/NN and MT7688AN: 64/128/256 MB (DDR2)
- RAM of MT7628DAN: 64 MB (DDR2)
- FLASH:8/16/32 MB (SPI NOR)
- Ethernet:3x 10/100 Mbps ethernet ports (MT76x8 built-in switch)
- WIFI:1x 2T2R 2.4 GHz Wi-Fi
- LEDs:1x system status green LED, 1x wifi green LED,
       3x ethernet green LED
- Buttons:1x reset button
- 1x microSD slot
- 4x USB 2.0 port
- 1x mini-usb debug UART
- 1x DC jack for main power (DC 5V)
- 1x TTL/RS232 UART
- 1x TTL/RS485 UART
- 13x GPIO header
- 1x audio codec(wm8960)

Installation via OpenWrt:

The original firmware is OpenWrt, so both LuCI and sysupgrade can be used.

Installation via U-boot web:

1. Power on board with reset button pressed, release it
   after wifi led start blinking.
2. Setup static IP 192.168.1.123/4 on your PC.
3. Go to 192.168.1.8 in browser and upload "sysupgrade" image.

Installation via U-boot tftp:
1. Connect to serial console at the mini usb, which has been connected to UART0
   on board (115200 8N1)
2. Setup static IP 192.168.1.123/4 on your PC.
3. Place openwrt-firmware.bin on your PC tftp server (192.168.1.123).
3. Connect one of LAN ports on board to your PC.
4. Start terminal software (e.g. screen /dev/ttyUSB0 115200) on PC.
5. Apply power to board.
6. Interrupt U-boot with keypress of "2".
7. At u-boot prompts:
   Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
   Input device IP (192.168.1.8) ==:192.168.1.8
   Input server IP (192.168.1.123) ==:192.168.1.123
   Input Linux Kernel filename (root_uImage) ==:openwrt-firmware.bin
8. board will download file from tftp server, write it to flash and reboot.

Signed-off-by: Robinson Wu <wurobinson@qq.com>
[add license to DTS files, fix state_default and reduce to the mimimum,
move phy0tpt trigger to DTS, drop ucidef_set_led_timer, fix network ports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Adrian Schmutzler
b057862e24 Revert "ramips: fix flash layout for TP-Link TL-WR841N v14"
This reverts commit 1623defbdb.

As already stated in the reverted patch, the OEM firmware will
properly recreate the config partition if it is overwritten by
OpenWrt.

The main reason for adding the partition was the image size
restriction imposed by the 0x3d0000 limitation of the TFTP
flashing process. Addressing this by shrinking the firmware
partition is not a good solution to that problem, though:

1. For a working image, the size of the content has to be smaller
   than the available space, so empty erase blocks will remain.

2. Conceptually, the restriction is on the image, so it makes sense
   to implement it in the same way, and not via the partitioning.
   Users could e.g. do initial flash with TFTP restriction with
   an older image, and then sysupgrade into a newer one, so TFTP
   restriction does not apply.

3. The (content) size of the recovery image is enforced to 0x3d0000
   by the tplink-v2-image command in combination with
   TPLINK_FLASHLAYOUT (flash layout in mktplinkfw2.c) anyway.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-22 18:59:44 +02:00
Alexander Müller
1623defbdb ramips: fix flash layout for TP-Link TL-WR841N v14
The config partition was missing from the flash layout of the device.

Although the stock firmware resets a corrupted config partition to the
default values, the TFTP flash with an image bigger than 0x3d0000 will
truncate the image as the bootloader only copies 0x3d0000 bytes to flash
during TFTP flashing.

Fixed by adding the config partition and shrinking the firmware
partition.

Fixes: 3fd97c522b ("ramips: add support for TP-Link TL-WR841n v14")

Signed-off-by: Alexander Müller <donothingloop@gmail.com>
2020-07-19 02:01:06 +02:00
Adrian Schmutzler
11478524a2 ramips: consolidate Netgear devices for mt7628
This creates a common DTSI and shared image definition for the
relatively similar Netgear devices for mt7628 platform.

As a side effect, this raises SPI flash frequency for the R6120,
as it's expected to work there as well if it works for R6080 and
R6020.

Based on the data from the other devices, it also seems probable
the 5g MAC address for R6120 could be extracted from the caldata,
and the mtd-mac-address there could be dropped.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-13 10:37:22 +02:00
Tim Thorpe
edbc8e5512 ramips: add support for Netgear R6020
This adds support for the Netgear R6020, aka Netgear AC750.

The R6020 appears to be the same hardware as the Netgear R6080,
aka Netgear AC1000, but it has a slightly different flash layout,
and no USB ports.

Specification:

SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB

MAC addresses based on vendor firmware:
LAN      *:88   0x4
WAN      *:89
WLAN2    *:88   0x4
WLAN5    *:8a   0x8004

The factory partition might have been corrupted beforehand. However,
the comparison of vendor firmware and OpenWrt still allowed to retrieve
a meaningful assignment that also matches the other similar devices.

Installation:

Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6020, and power the R6020 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6020-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6020. After flashing has finished,
power cycle the R6020, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.

Signed-off-by: Tim Thorpe <timfthorpe@gmail.com>
[slightly extend commit message, fix whitespaces in DTS, align From:
with Signed-off-by]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-10 11:39:05 +02:00
Rowan Border
33fae8421e ramips: add support for TP-Link RE220 v2
TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.

This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at>
for the TP-Link RE200 v2 as both devices share the same SoC, flash layout
and GPIO pinout.

Specifications

MediaTek MT7628AN (580 Mhz)
64 MB of RAM
8 MB of FLASH
2T2R 2.4 GHz and 1T1R 5 GHz
1x 10/100 Mbps Ethernet
UART header on PCB (57600 8n1)
8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled separately.

Web Interface Installation

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Signed-off-by: Rowan Border <rowanjborder@gmail.com>
2020-06-30 17:23:32 +02:00
David Bauer
1ba0466d43 package: add ravpower-mcu package
This package allows to read battery status information and control the
power state of the RAVPower RP-WD009 power management IC.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 12:24:04 +02:00
David Bauer
e959048c12 ramips: add support for RAVPower RP-WD009
The RAVPower RP-WD009 is a batter-powered pocket sized router with SD
card lot and USB port.

Hardware
--------
CPU:   MediaTek MT7628AN
RAM:   64M DDR2
FLASH: 16M GigaDevices SPI-NOR
WLAN:  MediaTek MT7628AN 2T2R b/g/n
       MediaTek MT7610E  1T1R n/ac
ETH:   1x FastEthernet
SD:    SD Card slot
USB:   USB 2.0

Custom PMIC on the I2C bus (address 0x0a).

Installation
------------

1. Press and hold down the reset button.

2. Power up the Device. Keep pressing the reset button for 10
   more seconds until the Globe LED lights up.

3. Attach your Computer to the Ethernet port. Assign yourself the
   address 10.10.10.1/24.

4. Access the recovery page at 10.10.10.128 and upload the OpenWrt
   factory image.

5. The flashing will take around 1 minute. The device will reboot
   automatically into OpenWrt.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 12:24:01 +02:00
Lars Wessels
dbaf0d20bb ramips: add support for WAVLINK WL-WN577A2
This commit adds support for the Wavlink WL-WN577A2 (black case) dual-band
wall-plug wireless router. In Germany this device is sold under the brand
name Maginon WL-755 (white case):

Device specifications:

- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps (Ralink RT3050)
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: 1 programmable (WPS) + LAN, WAN, POWER
- Buttons: Reset, WPS
- Small sliding power switch

Flashing instructions (U-boot):

- Configure a TFTP server on your PC/Laptop and set its IP
  to 192.168.10.100

- Rename the OpenWrt image to firmware.bin and place it in the
  root folder of the TFTP server

- Power off (using the small sliding power switch on the left
  side) the device and connect an ethernet cable from its LAN
  or WAN port to your PC/Laptop

- Press the WPS button (and keep it pressed)

- Power on the device (using the small power switch)

- After a few seconds, when the WAN/LAN LED stops blinking
  very fast, release the WPS button

- Flashing OpenWrt takes less than a minute, system will
  reboot automatically

- After reboot the WPS LED will indicate the current OpenWrt
  running status

Signed-off-by: Lars Wessels <software@bytebox.org>
[removed unused labels - fix whitespace errors - wrap commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 01:08:01 +02:00
Alex Lewontin
bd49f2c984 ramips: add support for Netgear R6080
This adds support for the Netgear R6080, aka Netgear AC1000.

The R6080 has almost the same hardware as the Netgear R6120,
aka Netgear AC1200, but it lacks the USB port, has only 8 MiB flash and
uses a different SERCOMM_HWID.

Specification:

SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB

Installation:

Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6080, and power the R6080 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6080-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6080. After flashing has finished,
power cycle the R6080, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[rebase and adjust for 5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-27 00:29:45 +02:00
Alex Lewontin
2e47a05d87 ramips: clean up Netgear R6120 code formatting
This commit performs minor janitorial work to clean up some code
formatting for the Netgear R6120.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
2020-06-23 21:56:44 +02:00
Ernst Spielmann
c3dc52e39a ramips: add support for Asus RT-N10P V3 / RT-N11P B1 / RT-N12 VP B1
Specifications:

- MT7628NN @ 580 MHz
- 32 MB RAM
- 8 MB Flash
- 5x 10/100 Mbps Ethernet (built-in switch)
- 2.4 GHz WLAN
- 2x external, non-detachable antennas (1x for RT-N10P V3)

Flash instructions:

1. Set PC network interface to 192.168.1.75/24.
2. Connect PC to the router via LAN.
3. Turn router off, press and hold reset button, then turn it on.
4. Keep the button pressed till power led starts to blink.
5. Upload the firmware file via TFTP. (Any filename is accepted.)
6. Wait until the router reboots.

Signed-off-by: Ernst Spielmann <endspiel@disroot.org>
[fix node/property name for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-24 18:14:59 +02:00
Sungbo Eo
a5720d3276 ramips: tidy up image subtarget Makefiles
- use tab indent in image build recipes for consistency
- harmonize line wrapping

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[use different line wrapping for one recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-08 18:58:39 +02:00
Sungbo Eo
d16a486766 ramips: fix SUPPORTED_DEVICES for Mercury MAC1200R v2
Currently SUPPORTED_DEVICES only contains the old device string. Fix it by
removing the first assignment.

Fixes: c2334ad60d ("ramips/mt76x8: Synchronize Makefiles with DTS compatible")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-26 21:10:24 +02:00
Chuanhong Guo
d7d46da938 ramips: disable images for 4M devices
default initramfs for 5.4 kernel is larger than 4M, causing build error
for oversized initramfs image.
disable these images because we have no mechanism for ignoring initramfs
errors and the squashfs image will be larger than initramfs anyway.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Sungbo Eo
3f14f034fb treewide: omit IMAGE_SIZE argument from check-size
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-21 20:02:55 +01:00
Sungbo Eo
6410c30dc7 ramips: add support for TOTOLINK A3
TOTOLINK A3 is a clone of ipTIME A3. The only difference is the model name.

Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
  - Switch: SoC internal

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Tested on device by JasonHCH <hsuan670629@gmail.com>

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-03-13 14:05:00 +01:00
Andreas Böhler
6d6f36ae78 ramips: add support for TP-Link RE200 v2
TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.

Specifications
--------------

- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled), 2x button

There are 2.4G and 5G LEDs in red and green which are controlled
separately.

MAC addresses
-------------

The MAC address assignment matches stock firmware, i.e.:
LAN : *:0D
2.4G: *:0E
5G  : *:0F

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Serial console
--------------

Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.

Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.

Additonal notes
---------------

It is possible to flash back to stock by using tplink-safeloader to create
a sysupgrade image based on a stock update. After the first boot, it is
necessary upgrade to another stock image, otherwise subsequent boots
fail with LZMA ERROR 1 and you have to attach serial to recover the device.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
[remove DEVICE_VARS change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-01 19:41:51 +01:00
Adrian Schmutzler
3227afbbab ramips: collect and harmonize TP-Link image variants in common file
This moves the various variants of common device definitions for
TP-Link devices to a common Makefile common-tp-link.mk. This
provides the opportunity to reorganize and move parameters between
individual device definitions and the common ones.

While at it, also use the common definitions for previously
independent definitions where appropriate.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-01 19:35:35 +01:00
David Bauer
b30f2281cc ramips: add support for GL.iNet microuter-N300
The GL.iNet microuter-N300 (internally referred as MT300N-v4) is a
pocket-size travel router. It is essentially identical to the VIXMINI
(internally referred as MT300N-v3) but with double the RAM and
SPI-flash.

Additionally, set the label-mac for both the VIXMINI as well as the
microuter-N300.

Hardware
--------
SoC:   MediaTek MT7628NN
RAM:   128M DDR2
FLASH: 16M
LED:   Power - WLAN
BTN:   Reset
UART:  115200 8N1
       TX and RX are labled on the board as pads next to the SoC

Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
   Note: The ethernet port is by default WAN. So you need to connect to
   the router via WiFi

2. Navigate to the Update tab on the left side.

3. Select "Local Update"

4. Upload the OpenWrt sysupgrade image.
   Note: Make sure you select not to preserve the configuration.

Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
   Wait for the LED to flash 5 times.

2. Assign yourself a static IPv4 in 192.168.1.0/24

3. Upload the OpenWrt sysupgrade image at 192.168.1.1.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-01-29 15:10:54 +01:00
Adrian Schmutzler
dc862be301 ramips: define SOC only once for uniform targets
In ramips, all devices in mt7621, mt76x8 and rt288x subtarget have
the same value set to the SOC variable for each device individually.

This patch introduces a non-device-dependent variable DEFAULT_SOC,
which is used if no specific SOC is set for a device, and thus reduces
the number of redundant definitions drastically.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-24 17:16:11 +01:00