Commit Graph

167 Commits

Author SHA1 Message Date
Stefan Kalscheuer
b308bd50ef kernel: migrate FORCE_MAX_ZONEORDER to ARCH_FORCE_MAX_ORDER for 6.1
The flag FORCE_MAX_ZONEORDER was renamed to ARCH_FORCE_MAX_ORDER in
Kernel 6.1 [1]. Rename the flag in generic Kconfig and remove it from
target configs.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=0192445cb2f7ed1cd7a95a0fc8c7645480baba25

Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
2023-06-25 11:26:50 +02:00
John Audia
e0fb38f4ee kernel: bump 6.1 to 6.1.35
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-06-23 23:07:17 +02:00
John Audia
1f5fce27c1 kernel: bump 5.15 to 5.15.118
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-06-23 23:05:45 +02:00
Daniel González Cabanelas
df8e4b6c2e bmips: add support for Arcadyan AR7516
The Arcadyan AR7516, AKA Orange Bright Box or EE Bright Box 1, is a wifi
fast ethernet router, 2.4 GHz single band with two internal antennas. It
comes with a horizontal stand black shiny casing.

Newer Bright Box 1 model stands vertically, and comes with a totally
different board inside, not compatible with this firmware.

Hardware:
 - SoC: Broadcom BCM6328
 - CPU: single core BMIPS4350 V7.5 @ 320Mhz
 - RAM: 64 MB DDR2
 - Flash: 8 MB SPI NOR
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4 GHz: Broadcom BCM43227 802.11bgn (onboard)
 - USB: 1x 2.0
 - ADSL: yes, unsupported
 - Buttons: 2x
 - LEDs: 9x, power LED is hardware controlled
 - UART: yes

Installation in two steps, new CFE bootloader and firmware:

Install new CFE:
  1. Power off the router and press the RESET button
  2. Power on the router and wait some seconds
  3. Release the RESET button
  3. Browse to http://192.168.1.1, this web interface will offer both
     firmware (“Software”) upgrade and bootloader upgrade; be sure to
     use the bootloader section of the upload form.
  4. Upload the new CFE (availabe at the wiki page)
  5. Wait about a minute for flashing to finish and reboot into the new bootloader.

Install OpenWrt via new CFE web UI:
  1. After installing the new CFE, visit http://192.168.1.1
  2. Upload the Openwrt cfe firmware
  5. Wait a few minutes for it to finish

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-22 17:53:32 +02:00
Daniel González Cabanelas
6cb3328b4f bmips: add support for NuCom R5010UNv2
The NuCom R5010UNv2 is a wifi fast ethernet router, 2.4 GHz single band
with two external antennas.

Hardware:
 - SoC: Broadcom BCM6328
 - CPU: single core BMIPS4350 V7.5 @ 320Mhz
 - RAM: 64 MB DDR2
 - Flash: 16 MB SPI NOR
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4 GHz: Broadcom BCM43217 802.11bgn (onboard)
 - USB: 1x 2.0
 - Buttons: 2x
 - ADSL: yes, unsupported
 - LEDs: 7x
 - UART: yes

Installation via CFE web UI:
  1. Power off the router and press the RESET button
  2. Power on the router and wait 12 or more seconds
  3. Release the RESET button
  4. Browse to http://192.168.1.1 and upload the Openwrt cfe firmware
  5. Wait a few minutes for it to finish

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-19 20:39:52 +02:00
Daniel González Cabanelas
6d1265b148 bmips: enable the data Read Ahead Cache for BMIPS4350
The data RAC is left disabled by the bootloader in some SoCs, at least in
the core it boots from. Enabling this feature increases the performance up
to +30% depending on the task.

The kernel enables the whole RAC unconditionally on BMIPS3300 CPUs. Enable
the data RAC in a similar way also for BMIPS4350.

Tested on DGND3700 v1 (BCM6368) and HG556a (BCM6358).

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-18 20:06:06 +02:00
Álvaro Fernández Rojas
62cdca25ed bmips: fix DMA RAC flush
BMIPS_GET_CBR() returns an invalid address on some SoCs.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-18 19:50:23 +02:00
Álvaro Fernández Rojas
47cc09aa7a bmips: add support for Comtrend VG-8050
The Comtrend VG-8050 is a wifi gigabit ethernet router, 2.4 GHz single band with
two external antennas.

Hardware:
 - SoC: Broadcom BCM63169
 - CPU: dual core BMIPS4350 @ 400Mhz
 - RAM: 128 MB DDR
 - Flash: 128 MB NAND
 - LAN switch: Broadcom BCM53125, 5x 1Gbit
 - Wifi 2.4 GHz: SoC (BCM63268) 802.11bgn
 - USB: 1x 2.0 (optional)
 - Buttons: 2x (reset)
 - LEDs: yes
 - UART: yes

Installation via CFE web UI:
  1. Power off the router.
  2. Press reset button near the power switch.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Browse to http://192.168.1.1 and upload the firmware.
  5. Wait a few minutes for it to finish.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-16 09:48:53 +02:00
Álvaro Fernández Rojas
d9210c5ff7 bmips: dts: dgnd3700: fix WAN port
All switch ports are labeled as port@address so let's follow the same pattern.

Fixes: ed79519b8d ("bmips: add support for Netgear DGND3700 v1, DGND3800B")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-15 20:53:11 +02:00
Álvaro Fernández Rojas
38ebb2eafd bmips: add support for Sercomm AD1018
The Sercomm AD1018 is a wifi fast ethernet router, 2.4 GHz single band with
two internal antennas.

Hardware:
 - SoC: Broadcom BCM6328
 - CPU: single core BMIPS4350 @ 320Mhz
 - RAM: 64 MB (v1) / 128 MB (v2) DDR
 - Flash: 128 MB NAND
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4 GHz: miniPCI Broadcom BCM43217 802.11bgn
 - USB: 1x 2.0
 - Buttons: 3x (reset)
 - LEDs: yes
 - UART: yes

Installation via OEM web UI:
  1. Use the admin credentials to login via web UI
  2. Go to Managament->Update firmware and select the OpenWrt CFE firmware
  3. Press "Update Firmware" button and wait some minutes until it finish

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-15 20:47:40 +02:00
Álvaro Fernández Rojas
434434ca47 bmips: bump LOADER_ENTRY to RAM + 16M
This is needed on devices like Sercomm AD1018 for booting recent kernels due
to bigger kernels.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-15 20:47:40 +02:00
Daniel González Cabanelas
e1a55de7a7 bmips: add support for Actiontec R1000H
The  Actiontec R1000H is a gigabit wifi router, 2.4 GHz single band with
two external antennas. It comes with a coaxial HomePNA port.

Hardware:
 - SoC: Broadcom BCM6368
 - CPU: dual core BMIPS4350 V3.1 @400Mhz
 - RAM: 64 MB DDR
 - Flash: 32 MB parallel NOR
 - LAN switch: Broadcom BCM53115, 5x 1Gbit
 - LAN coaxial : 1x HPNA 3.1, CG3211 + CG3213
 - Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
 - USB: 1x 2.0
 - Buttons: 2x, 1 reset
 - LEDs: 7x
 - UART: yes

The HPNA hardware probably needs a firmware to make the coaxial port work.
In the OEM firmware, it's apparently sent with an utility (inhpna) through
the ethernet port.

Installation via CFE web UI:
  1. Connect the UART serial port.
  2. Power on the router and press enter at the console prompt to stop the
     bootloader.
  4. Browse to http://192.168.1.1 and upload the OpenWrt CFE firmware
  5. Wait a few minutes for it to finish

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-15 17:58:58 +02:00
Álvaro Fernández Rojas
464dfac049 bmips: switch to standard nand_do_upgrade
Now that JFFS2 cleanmarkers are supported on the standard nand_do_upgrade
function we can start using it on bmips.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-15 10:51:21 +02:00
Álvaro Fernández Rojas
915e914cfa bmips: fix NETGEAR DGND3700v2 boot loop
The DGND3700v2 renames the cferam bootloader from cferam to cfeXXX, where XXX
is the number of firmware upgrades performed by the bootloader. Other bcm63xx
devices rename cferam.000 to cferam.XXX, but this device is special because
the cferam name isn't changed on the first firmware flashing but it's changed
on the subsequent ones.
Therefore, we need to look for "cfe" instead of "cferam" to properly detect
the cferam partition and fix the bootlop.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-14 23:23:14 +02:00
Álvaro Fernández Rojas
bcdf861519 bmips: add support for Comtrend AR-5381u
The Comtrend AR-5381u is a wifi fast ethernet router, 2.4 GHz single band with
two internal antennas.

Hardware:
 - SoC: Broadcom BCM6328
 - CPU: single core BMIPS4350 @ 320Mhz
 - RAM: 64 MB DDR
 - Flash: 16 MB SPI NOR
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4 GHz: miniPCI Broadcom BCM43225 802.11bgn
 - USB: 1x 2.0
 - Buttons: 1x (reset)
 - LEDs: yes
 - UART: yes

Installation via CFE web UI:
  1. Power off the router.
  2. Press reset button near the power switch.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Browse to http://192.168.1.1 and upload the firmware.
  5. Wait a few minutes for it to finish.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-12 18:53:00 +02:00
Álvaro Fernández Rojas
c3b1ef2dfd bmips: add support for Comtrend WAP-5813n
The Comtrend WAP-5813n is a wifi gigabit router, 2.4 GHz single band with
two external antennas.

Hardware:
 - SoC: Broadcom BCM6369
 - CPU: dual core BMIPS4350 @ 400Mhz
 - RAM: 64 MB DDR
 - Flash: 8 MB parallel NOR
 - LAN switch: Broadcom BCM53115, 5x 1Gbit
 - Wifi 2.4 GHz: miniPCI Broadcom BCM4322 802.11bgn
 - USB: 1x 2.0 (optional)
 - Buttons: 3x (reset)
 - LEDs: yes
 - UART: yes

Installation via CFE web UI:
  1. Power off the router.
  2. Press reset button near the power switch.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Browse to http://192.168.1.1 and upload the firmware.
  5. Wait a few minutes for it to finish.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-11 18:31:23 +02:00
Álvaro Fernández Rojas
3baa45fbd8 bmips: add support for Comtrend VR-3025un
The Comtrend VR-3025un is a wifi gigabit router, 2.4 GHz single band with
two external antennas.

Hardware:
 - SoC: Broadcom BCM6368
 - CPU: dual core BMIPS4350 @ 400Mhz
 - RAM: 64 MB DDR
 - Flash: 8 MB parallel NOR
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4 GHz: miniPCI Broadcom BCM43222 802.11bgn
 - USB: 1x 2.0
 - Buttons: 1x (reset)
 - LEDs: yes
 - UART: yes

Installation via CFE web UI:
  1. Power off the router.
  2. Press reset button near the antenna.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Browse to http://192.168.1.1 and upload the firmware.
  5. Wait a few minutes for it to finish.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-11 12:09:40 +02:00
Álvaro Fernández Rojas
79844637df bmips: dgnd3700v1/dgnd3800b: add missing kmod-leds-gpio
Commit ed79519b8d missed adding kmod-leds-gpio to these devices.

Fixes: ed79519b8d ("bmips: add support for Netgear DGND3700 v1, DGND3800B")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-11 10:25:03 +02:00
Álvaro Fernández Rojas
389f7802db bmips: image: rename Device/bcm63xx_netgear
Every other Device definition in the target is using hyphens instead of
underscores.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-11 10:17:50 +02:00
Álvaro Fernández Rojas
130e5c63c7 bmips: dts: improve and align device tree files
Align all the device tree files and follow the same criteria before more
devices are ported from bcm63xx and this goes out of control.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-11 10:14:25 +02:00
Daniel González Cabanelas
71a6f45fdf bmips: add support for Netgear EVG2000
The Netgear EVG2000 is a wifi gigabit router, 2.4 GHz single band with
two internal antennas integrated in the main PCB.

Hardware:
 - SoC: Broadcom BCM6369
 - CPU: dual core BMIPS4350 V3.1 @400Mhz
 - RAM: 64 MB DDR
 - Flash: 16 MB parallel NOR
 - LAN switch: Broadcom BCM53115, 5x 1Gbit
 - Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
 - USB: 2x 2.0
 - Buttons: 2x, 1 reset
 - LEDs: 10x
 - FXS: 2x
 - UART: yes

Installation via CFE web UI:
  1. Power off the router and make a temporal TX-RX shortcircuit on the
     serial pins.
  2. Power on the router and wait 3 or more seconds
  3. Remove the TX-RX shortcircuit
  4. Browse to http://192.168.1.1 or http://192.168.0.1 and upload the
     firmware
  5. Wait a few minutes for it to finish

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-11 09:54:52 +02:00
Daniel González Cabanelas
ed79519b8d bmips: add support for Netgear DGND3700 v1, DGND3800B
The Netgear DGND3700 v1 and DGND3800B are the same device but with
different factory firmwares. It's an xDSL wifi router with a slim black
shiny casing and 4 PCB internal antennas connected via UFL to a miniPCI
detachable card.

Hardware:
 - SoC: Broadcom BCM6368
 - CPU: dual core BMIPS4350 V3.1 @400Mhz
 - RAM: 128 MB DDR
 - NOR Flash: 32 MB parallel (CFE and OS)
 - NAND flash: 128 MB (empty)
 - Ethernet LAN: 5x 1Gbit
 - Wifi 2.4 GHz: Broadcom BCM43222 802.11bgn
 - Wifi 5 GHz: Broadcom BCM43222 802.11abgn
 - USB: 2x 2.0
 - Buttons: 3x, 1 reset
 - LEDs: 11x
 - UART: yes

Installation via OEM web UI:
  1. Open the Netgear administration web interface, by default:
        http://192.168.0.1
	user: admin
        password: password
  2. Look for "upgrade firmware" and proceed
  3. Wait some minutes until it finishes

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-10 15:37:52 +02:00
Álvaro Fernández Rojas
47ca33a0be bmips: bump LZMA Loader address
This allows booting bigger ramdisk images via TFTP at the cost of breaking 32M
RAM compatibility, but those devices have been unable to boot ramdisks on this
target for some time anyway due to not having enough RAM.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-09 19:48:42 +02:00
Daniel González Cabanelas
e7a0b61397 bmips: add support for Observa VH4032N
The Observa VH4032N is an xDSL wifi router with a vertical white casing
and two internal antennas connected via UFL.

Hardware:
 - SoC: Broadcom BCM6368
 - CPU: dual core BMIPS4350 V3.1 @400MHz
 - RAM: 128 MB DDR
 - Flash: 32 MB parallel NOR
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4/5 GHz: onboard Broadcom BCM43222 802.11abgn
 - USB: 3x 2.0
 - Buttons: 2x, 1 reset
 - LEDs: 8x, blue and red
 - UART: 1x

Installation via OEM web UI:
  1. Use the admin credentials to login via web UI
  2. Go to Managament->Update firmware and select the OpenWrt CFE firmware
  3. Press "Update Firmware" button and wait some minutes until it finish

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-09 19:44:28 +02:00
Robert Marko
b81045a818 kernel: bump 6.1 to 6.1.31
All patches automatically rebased.

Build system: x86_64/Fedora 38
Build-tested: ipq807x/Qnap 301W, ipq807x/Dynalink DL-WRX36
Run-tested: ipq807x/Qnap 301W, ipq807x/Dynalink DL-WRX36

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-06-02 21:23:12 +02:00
Álvaro Fernández Rojas
2aca88ef8d bmips: enable testing kernel version with 6.1 version
Enable testing kernel version with 6.1 kernel version.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-05-30 21:00:34 +02:00
Álvaro Fernández Rojas
f6c02b014d bmips: 6.1: refresh config and add missing symbols
Refresh config for kernel 6.1 and add missing symbols.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-05-30 21:00:24 +02:00
Álvaro Fernández Rojas
959d3f0582 bmips: 6.1: refresh kernel patches
Refresh kernel patches for version 6.1.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-05-30 20:55:12 +02:00
Álvaro Fernández Rojas
a937eef305 bmips: 6.1: copy patches, config from 5.15
Copy patches and config from 5.15 kernel version.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-05-30 20:55:12 +02:00
Álvaro Fernández Rojas
8f6033e287 bmips: enet: add compatibility with kernel 6.1
Make bmips ethernet drivers compatible with 6.1 kernel.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-05-30 20:54:54 +02:00
Álvaro Fernández Rojas
0dd5505a17 bmips: improve kernel patches
Add missing patch headers and regenerate the ones that contain an obsolete
patch header.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-05-17 18:25:40 +02:00
Christian Marangi
150508e47c
bmips: 5.15: comment unused macronix_nand_block_protection_support
Comment unused function macronix_nand_block_protection_support since it
does cause boot problem
Fix compilation error:
drivers/mtd/nand/raw/nand_macronix.c:220:13: error: 'macronix_nand_block_protection_support' defined but not used [-Werror=unused-function]
  220 | static void macronix_nand_block_protection_support(struct nand_chip *chip)
      |             ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-05-12 03:15:42 +02:00
Álvaro Fernández Rojas
c3549b9319 bmips: fix external interrupt controller
- irq_domain_add_simple() can't be used on bmips since interrupts aren't
hardcoded with specific offsets for internal and external as opposed to
bcm63xx. This is needed to avoid collisions with other interrupts.
- remove unused bcm63xx-specific code.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-27 15:39:09 +02:00
Álvaro Fernández Rojas
e9f5b773d2 bmips: document GPIO external interrupts
BCM63xx SoCs have an external interrupt controller which can be used for
specific GPIO keys.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-27 15:39:09 +02:00
Álvaro Fernández Rojas
11de53729a bmips: increment polled keys interval to 100
There's no need to poll the gpio keys every 20 ms and the linux kernel
documentation suggests 100 ms.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-27 15:39:09 +02:00
Álvaro Fernández Rojas
3132eff000 bmips: shg2500: add BCM4360 fallback SPROM
Apart from the embedded BCM63268 wireless, this device has an external BCM4360
connected by PCIe which needs a fallback SPROM.
b43 isn't enabled for this device because BCM4360 isn't supported (AC PHY).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-23 12:19:02 +02:00
Álvaro Fernández Rojas
0cecebd413 bmips: dgnd3700v2: add b43 wireless driver
Apart from the embedded BCM6362 wireless, Netgear DGND3700v2 has external
BCM43228 wireless connected by PCIe.
Fallback SPROM isn't needed for this one because it has a physical SPROM.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-23 12:19:02 +02:00
Álvaro Fernández Rojas
7f285b9c1d bmips: leds-sercomm-msp430: improve driver
- Add missing module functions.
- Fix infinite pattern trigger by converting negative values to 0.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-23 12:19:02 +02:00
Álvaro Fernández Rojas
f6f4db6e4d bmips: enet: add missing module functions
- Add missing MODULE_DEVICE_TABLE().
- Switch bcm6348-iudma to module_platform_driver().
- Add missing MODULE_AUTHOR, MODULE_DESCRIPTION, MODULE_LICENSE and
MODULE_ALIAS.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-23 12:19:02 +02:00
Álvaro Fernández Rojas
b98955c623 bmips: pci: use standard module functions
late_initcall_sync() is no longer needed so standard module functions can be
used on all bmips PCI/PCIe drivers.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-23 12:19:02 +02:00
Álvaro Fernández Rojas
7872a0ee2c bmips: drop custom b43-sprom fixups
b43-sprom fixups and no longer used and can be removed from bmips targets.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-23 12:18:36 +02:00
Álvaro Fernández Rojas
7122609082 bmips: switch to generic bcma/ssb fallback SPROM
Stop using bmips b43-sprom fixups and switch to generic bcma/ssb fallback
SPROMs. This way we don't need to include the b43-sprom fixups on devices
without Broadcom wireless.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-23 12:18:35 +02:00
Álvaro Fernández Rojas
5ec781c444 bmips: pci-bcm6348: load IO resource from DT ranges
Correctly load IO resource from DT ranges and remove the specific IO resource.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-18 20:11:28 +02:00
Álvaro Fernández Rojas
16b0cbbde0 bmips: drop unneeded ath9k fixup
We no longer need the custom ath9k fixup now that we're using the standard
kmod-owl-loader.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-18 19:45:04 +02:00
Álvaro Fernández Rojas
db4f158c03 bmips: hg556a: switch to kmod-owl-loader
Stop using custom ath9k fixup and switch to standard kmod-owl-loader

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-18 19:45:04 +02:00
Álvaro Fernández Rojas
457549665f bmips: dts: add missing phy modes
PHY modes should be defined in the device tree for the bcm63xx internal switch.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-10 10:06:22 +02:00
Álvaro Fernández Rojas
2c824b4615 bmips: remove source-only flag
bmips target is now more stable and it's time to start generating buildbot
images in order to receive a wider testing, which will be essential to replace
bcm63xx target in the future.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-10 10:04:08 +02:00
Álvaro Fernández Rojas
6fd8e0f943 bmips: add subtargets for each SoC
BMIPS is a generic arch that can be used for multiple Broadcom SoCs, each one
with its own specific drivers, so instead of having a huge kernel supporting
all of them, let's switch to a subtarget per SoC like other OpenWrt targets.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-10 10:04:08 +02:00
Álvaro Fernández Rojas
e76556d967 bmips: b43-sprom: fix build when SSB/BCMA disabled
Fix build of B43 SPROM fallback when SSB or BCMA are disabled.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-10 10:04:08 +02:00
Álvaro Fernández Rojas
95b846fbc0 bmips: allow disabling mdio-mux-bcm6368
This controller is only present on SoCs with B53 MMAP switch.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-10 10:04:08 +02:00