Bumping package version has been overlooked in a previous commit.
While at it, use PKG_RELEASE instead of PKG_VERSION, as the latter
is meant for upstream version number only.
(The effective version string for the package would be "3" in both
cases, so there is no harm done for version comparison.)
Fixes: 0453c3866f ("vxlan: fix udp checksum control")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the Ubiquiti PowerBridge M, which has the same
board/LEDs as the Bullet M XM, but different case and antennas.
Specifications:
- AR7241 SoC @ 400 MHz
- 64 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- Internal antenna: 25 dBi
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via WebUI:
Upload the factory image via the stock firmware web UI.
Attention: airOS firmware versions >= 5.6 have a new bootloader with
an incompatible partition table!
Please downgrade to <= 5.5 _before_ flashing OpenWrt!
Refer to the device's Wiki page for further information.
Flashing via TFTP:
Same procedure as other Bullet M (XM) boards.
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbridge-m-squashfs-factory.bin
Signed-off-by: Vieno Hakkerinen <vieno@hakkerinen.eu>
So far, passing "rxcsum" and "txcsum" had no effect.
Fixes: 95ab18e012 ("vxlan: add options to enable and disable UDP
checksums")
Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Feature detection doesn't recognize ipset v7 use on kernel v5.x systems
and thus disables the tc ematch function em_ipset.
- backport patch:
* 002-configure-support-ipset-v7.patch:
650591a7a70c configure: support ipset version 7 with kernel version 5
Fixes: 4e0c54bc5b ("kernel: add support for kernel 5.4")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Recent iproute2 5.x versions modified the symbols resolved for plugins,
causing "tc .. action xt .." to fail. Update the list of symbols to fix.
Fixes: b61495409b ("iproute2: tc: reduce size of dynamic symbol table")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
As the the SoC uses implicit vlan tagging for dual MAC support, the
offload feature breaks when using double tagging.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: John Crispin <john@phrozen.org>
Having looked at this again, it appears that only gsbi2_serial
is actually enabled for this device, so the entry in the broken
aliases node was correct.
Therefore, this needs to set its own serial0 instead of inheriting
"serial0 = &gsbi4_serial;" from DTSI. Do this with the correctly
named aliases node now.
Fixes: c83f7b6d21 ("ipq806x: fix aliases node name for Qualcomm
IPQ8064/DB149")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Kernel uses the label gsbiX_serial, so let's adjust our labels to
this naming scheme.
This is cosmetic, and actually only already existing gsbi4_serial
has been used at all.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device uses a node incorrectly named "alias" instead of
"aliases" since it was introduced.
Remove it without replacement, as the definitions in it don't
seem to be required anyway:
The serial0 definition has never been effective anyway and this
would be the only device deviating from the common setting
"serial0 = &gsbi4_serial;" for ipq8064. (So, maybe the wrong
node prevented us from finding out about the wrong serial
definition?)
The mdio-gpio0 alias was supposed to be removed in d2a2eb7e48
anyway, the redundant definition in the alias node was just
overlooked back then.
Fixes: 0fd202f3e5 ("ipq806x: add db149 dts files")
Fixes: d2a2eb7e48 ("ipq806x: replace caf nss-gmac driver by upstream stmmac")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Optional instance watchdog timeout and watchdog mode can be set by
adding: procd_set_param $mode $timeout
$mode is an integer [0-1] representing instance watchdog mode of
operation:
0 = disabled
1 = passive mode, client must periodically poke watchdog via ubus
$timeout is an integer representing how often, in seconds, the watchdog must be poked.
Signed-off-by: Daniel Bailey <danielb@meshplusplus.com>
Since commit 6f2e1b7485 (ath79: disable delays on AT803X config init)
the incoming incoming traffic on the ubnt,lap-120 devices Ethernet
port was not making it through. Using rgmii-id instead of rgmii (same
configuration as ubnt,litebeam-ac-gen2) fixes it.
Fixes FS#2893.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
The f-string feature was introduced in Python 3.6. As Buildbots may run
on Debian 9, which comes per default with Python 3.5, this would cause
an issue. Instead of f-strings use the *legacy* `.format()` function.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Specifications:
SoC: MT7621AT
RAM: 128MB
Flash: 16MB NOR SPI flash
WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
LAN: 5x1000M
Firmware layout is Uboot with extra 96 bytes in header
Base PCB is AP-MTKH7-0002
LEDs Power Green,Power Orange,Internet Green,Internet Orange
LEDs "2.4G" Green & "5G" Green connected directly to wifi module
Buttons Reset,WPS,WIFI
Flashing instructions:
Upload image via emergency recovery mode
Push and hold reset button (on the back of the device) until power led
starts flashing (about 10 secs or so) while powering the device on.
Give it ~30 seconds, to boot the recovery mode GUI
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
Call the recovery page for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device. Some browsers/OS combinations are known not to work, so if
you don't see the percentage complete displayed and moving within a few
seconds, restart the procedure from scratch and try anoher one,
or try the command line way.
Alternative method using command line on Linux:
curl -v -i -F "firmware=@openwrt-xxxx-squashfs-factory.bin" 192.168.0.1
Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com>
[use of generic uimage-padhdr in image generation code]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The timer LED trigger is enabled in all targets (except for lantiq
xway-legacy). It's necessary for the OpenWrt preinit LED pattern to
work.
Signed-off-by: David Bauer <mail@david-bauer.net>
Use the OpenWrt netlink GPIO button implementation to forward button
presses to procd. This is necessary to make failsafe-mode access
using a button possible.
Signed-off-by: David Bauer <mail@david-bauer.net>
aed7fb3 procd: fix compilation with uClibc-ng
9d0f831 jail: fix segfault with len(uidmap/gidmap) > 1
42a6217 jail: consider PATH for argv in OCI container
83f4b72 jail: actually chdir into OCI defined CWD
fc9f614 jail: parse and run OCI hooks
02eec92 jail: memory allocation fixes
71e75f4 jail: refactor mount support to cover OCI spec
b586e7d jail: don't make mount source read-only
dacab12 uxc: fix 'stop' command
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The device can only hold 3.6 MB, but newer images (since 18.06)
are bigger, so flashing a new version fails.
This disables default build for this device based on the bug report
referenced below.
Fixes: FS#1963
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This creates a common DTSI and shared image definition for the
relatively similar Netgear devices for mt7628 platform.
As a side effect, this raises SPI flash frequency for the R6120,
as it's expected to work there as well if it works for R6080 and
R6020.
Based on the data from the other devices, it also seems probable
the 5g MAC address for R6120 could be extracted from the caldata,
and the mtd-mac-address there could be dropped.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This release brings parity with the commits Linus released a few hours
ago into 5.8-rc5.
* receive: account for napi_gro_receive never returning GRO_DROP
The napi_gro_receive function no longer returns GRO_DROP ever, making
handling GRO_DROP dead code. This commit removes that dead code.
Further, it's not even clear that device drivers have any business in
taking action after passing off received packets; that's arguably out of
their hands.
* device: implement header_ops->parse_protocol for AF_PACKET
WireGuard uses skb->protocol to determine packet type, and bails out if
it's not set or set to something it's not expecting. For AF_PACKET
injection, we need to support its call chain of:
packet_sendmsg -> packet_snd -> packet_parse_headers ->
dev_parse_header_protocol -> parse_protocol
Without a valid parse_protocol, this returns zero, and wireguard then
rejects the skb. So, this wires up the ip_tunnel handler for layer 3
packets for that case.
* queueing: make use of ip_tunnel_parse_protocol
Now that wg_examine_packet_protocol has been added for general
consumption as ip_tunnel_parse_protocol, it's possible to remove
wg_examine_packet_protocol and simply use the new
ip_tunnel_parse_protocol function directly.
* compat: backport ip_tunnel_parse_protocol and ip_tunnel_header_ops
These are required for moving wg_examine_packet_protocol out of
wireguard and into upstream.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
We don't need to see how git will be executed and it produces non silent
output on 'scripts/env diff' commands when there are no differences
unlike before.
Re-introduce original silent behaviour.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
upstream changed dt-bindings for marvell 88e6060 to use mdio-device
and dropped support for legacy bindings.
fix it in our local dts.
Fixes: FS#2524
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Linux phy subsystem provides support for a phy regulator defined via
phy-supply property. Use it to turn on usb power only when usb is
probed.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Add support for Marvell MACCHIATObin Single Shot, cortex-a72 based
Marvell ARMADA 8040 Community board. Single Shot was broken as the
device tree is different on the Double Shot Board.
Specifications:
- Quad core Cortex-A72 (up to 2GHz)
- DDR4 DIMM slot with optional ECC and single/dual chip select support
- Dual 10GbE (1/2.5/10GbE) SFP+
2.5GbE (1/2.5GbE) via SFP
1GbE via copper
- SPI Flash
- 3 X SATA 3.0 connectors
- MicroSD connector
- eMMC
- PCI x4 3.0 slot
- USB 2.0 Headers (Internal)
- USB 3.0 connector
- Console port (UART) over microUSB connector
- 20-pin Connector for CPU JTAG debugger
- 2 X UART Headers
- 12V input via DC Jack
- ATX type power connector
- Form Factor: Mini-ITX (170 mm x 170 mm)
More details at http://macchiatobin.net
Installation:
Write the Image to your Micro SD Card and insert it in the
MACCHIATObin Single Shot SD Card Slot.
In the U-Boot Environment:
1. reset U-Boot environment:
env default -a
saveenv
2. prepare U-Boot with boot script:
setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000"
saveenv
or manually (hanging lines indicate wrapped one-line command):
setenv fdt_name armada-8040-mcbin-singleshot.dtb
setenv image_name Image
setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr
$image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv
bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
$kernel_addr - $fdt_addr'
saveenv
On newer Bootloaders (18.12) the Variables have been changed, use:
setenv fdt_name armada-8040-mcbin-singleshot.dtb
setenv image_name Image
setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr_r
$image_name;ext4load mmc 1:1 $fdt_addr_r $fdt_name;setenv
bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
$kernel_addr_r - $fdt_addr_r'
Reported-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: Alexandra Alth <alexandra@alth.de>
[add specs and installation as provided by Alexandra Alth]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Due to a line break, printf was accidentally called with three
arguments instead of two, causing a different output than before.
Fix it by splitting the printf command into two lines.
Fixes: 907053193a ("scripts/mkits.sh: replace echo -e with printf")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There are already two very similar recipes using uimage_padhdr
in ramips target, and a third one is about to be added.
Make the recipe more generic, so redefinitions are not necessary
anymore.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Bjørn Mork <bjorn@mork.no> [Zyxel WAP6805]
Between kernels 4.20 and 5.0, a new variant of this board has been
introduced ("Single Shot"), and the existing one has been renamed
with the appendix "Double Shot". [1]
This also adjusted the first compatible in the list:
marvell,armada8040-mcbin -> marvell,armada8040-mcbin-doubleshot
This patch updates the OpenWrt implementation of this device by
adjusting the relevant references to that compatible (i.e., our
board name).
To still provide support for 4.19 with our setup, this adds a
small patch to change the compatible there as well.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b1f0bbe2700051886b954192b6c1751233fe0f52
Cc: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The router Nucom R5010UN v2 has the partitions defined for a 8MB flash,
but the flash chip is 16MB size. We are wasting half of the flash.
Fix it and use generic names for partitions.
Fixes: 474cde6123 ("brcm63xx: probe SPI flash through DT")
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Set CCACHE_DIR to $(TOPDIR)/.ccache and CCACHE_BASEDIR to $(TOPDIR).
This allows to do clean and dirclean. Cache hit rate for test build
after dirclean is ~65%.
If CCACHE is enabled stats are printed out at the end of building process.
CCACHE_DIR config variable allows to override default, which could be useful
when sharing cache with many builds.
cacheclean make target allows to clean the cache.
Changes from v1:
- remove ccache directory using CCACHE_DIR variable
- remove ccache leftovers from sdk and toolchain make files
- introduce CONFIG_CCACHE_DIR variable
- introduce cacheclean make target
Signed-off-by: Roman Yeryomin <roman@advem.lv>
The current one only looks for mt76x2e and mt7603e, and
does not work for 2 or more same Wi-Fi chips.
Refactor the script to cover those cases.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
The firmware is currently just copied. It can end up with o= on the
device (this is the case for voice_ar9_firmware.bin for instance).
Instead of copying it the Makefile is changed to use the macro
"$(INSTALL_DATA)" in order for the file to be world-readable.
While at it refactor the device node creation in the init script with
loop.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
[removed 2nd part with custom group handling for device nodes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Define 64m IMAGE_SIZE for flash firmware.bin since the flash size
is 64MB. Define 48m LS_SYSUPGRADE_IMAGE_SIZE for flash sysupgrade.bin
which contains maximum 16MB kernel and 32MB rootfs according to
memory map.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Many Layerscape boards support both flash boot and SD card boot.
And different firmware and sysupgrade.bin are built for the two
boot methods. To identify them, a fix could be done on board name
by adding a postfix "-sdboot" for SD card boot.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
There had been an issue in Layerscape QSPI driver for very long
time, which made squashfs,jffs2 rootfs not work on QSPI NOR.
And the ubifs had been used as a workaround.
Now the issue has been fixed. So convert to use squashfs,jffs2
rootfs on QSPI NOR for Layerscape boards (LS1012ARDB/LS1046ARDB/
LS1088ARDB), and update u-boot bootargs for booting.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The rootfs squashfs is already highly (XZ) compressed. Storing the applet
messages in compressed form will increase the entropy and reduce the overall
image compression ratio.
Size diffs (compressed vs uncompressed):
busybox (the executable): 364596 vs 384804 bytes.
OpenWrt target images (the kernel image is unchanged, obviously):
omnia-medkit-openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs.tar.gz:
9163597 vs 9162531 bytes (1066 bytes difference).
openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin:
9161688 vs 9160600 bytes (1088 bytes difference).
openwrt-mvebu-cortexa9-cznic_turris-omnia-sysupgrade.img.gz:
9729550 vs 9729230 bytes (320 bytes difference).
All in all, we save just a little bit over 1 kiB. As an added bonus, we
also don't have to decompress the messages twice, (first from squashfs,
then from the bzip2 message storage).
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[added additional size comparision diff detaisl]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes following shellcheck warning:
In scripts/mkits.sh line 19:
"-k kernel [-D name -d dtb] -o its_file" "$(basename $0)"
^-- SC2086: Double quote to prevent globbing and word splitting.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
