DTS variable is not used in any device. Just drop it.
UBIFS_OPTS is not device-dependent here. Remove it from DEVICE_VARS.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
IMAGE_SIZE is widely used in many targets. Declare it in the default template to
clean up redundant code. This also prevents deriving IMAGE_SIZE unintentionally
from the previously defined device.
While at it, remove duplicate KERNEL_SIZE declaration.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The labels on the LAN ports of the TP-Link Archer C60 v1/v2 are
actually inverted compared to the ports of the internal switch.
Add this information to 02_network.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The labels on the LAN ports of the TP-Link Archer C60 v1/v2 are
actually inverted compared to the ports of the internal switch.
Add this information to 02_network.
This is the same for to-be-supported v3 of this device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The adjustment of the MAC address for Archer C60 v2 in 10_fix_wifi_mac
is broken since a "mac" partition is not set up for this device on
ar71xx. Instead, the MAC address is already patched correctly in
11-ath10k-caldata.
Remove the useless adjustment.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MAC addresses for lan/wan are swapped compared to the vendor
firmware. This adjusts to vendor configuration, which is:
lan *:7b label
wan *:7c label+1
2.4g *:7b label
5g *:7a label-1
Only one address is stored in <&mac 0x8>, corresponding to the label.
This has been checked on revisions v1, v2 and v3.
Since ar71xx calculates the ath10k MAC address based on the ethernet
addresses, the number there is adjusted, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MAC addresses for lan/wan are swapped compared to the vendor
firmware. This adjusts to vendor configuration, which is:
lan *:7b label
wan *:7c label+1
2.4g *:7b label
5g *:7a label-1
Only one address is stored in <&mac 0x8>, corresponding to the label.
This has been checked on revisions v1, v2 and v3.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fixes following error uncovered while building armvirt/64 on 5.4:
Package kmod-hwmon-sch5627 is missing dependencies for the following libraries:
watchdog.ko
That dependency was introduced in upstream via 2d8c7ff52c24
("hwmon/sch56xx: Depend on watchdog for watchdog core functions") in
v3.5.
The issue emerged in 5.4 because the kconfig symbol CONFIG_WATCHDOG_CORE
is now a tristate value. Previously it was a bool.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
SoC: MediaTek MT7621AT
WiFi: MediaTek MT7603 bgn 2T2R
MediaTek MT7615 ac 4T4R
Flash: 32M SPI (Macronix MX25L25635F)
RAM: 128M DDR3 (Winbond W631GG6KB)
LED: Dome (Blue / White)
BTN: Reset
Installation
------------
These instructions were written for firmware version v3.9.27.
Downgrade if necessary.
1. Copy the OpenWrt sysupgrade image to the devices /tmp folder
via scp. On factory defaults, user and password is "ubnt" at
192.168.1.20/24.
2. Write the bootselect flag. Otherwise, the device might boot from the
wrong partition. Verify the mtd partition used in the command below
is the one labled "bs" in /proc/mtd (as this might change in the
future).
> dd if=/dev/zero bs=1 count=1 of=/dev/mtd4
3. Write the OpenWrt sysupgrade to the mtd partitions labled
"kernel0" and "kernel1".
> dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock6
> dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock7
4. Reboot or powercycle the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
When sharing a common build directory between different build platforms
eg. macos v docker based linux v virtual machine, a 'make dirclean'
isn't quite enough to clean all the platform related binaries. The
'conf' and 'mconf' aka 'make menuconfig/defconfig & friends' utilities
remain.
Clean those as part of 'dirclean' so they get rebuilt for the current
platform on the next 'make'
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Ethernet, switch, LEDs, buttons, USB, sysupgrade & LuCI were
successfully tested on BCM4706.
WARNING: Hack for BCM4710 adding BCM4710_PROTECTED_FILL_TLB() to the
local_r4k_flush_cache_sigtramp() could not be ported. That function has
been dropped in:
commit adcc81f148d7 ("MIPS: math-emu: Write-protect delay slot emulation pages")
commit 3315b6b336c8 ("MIPS: Delete unused flush_cache_sigtramp()")
it's unsure if that chipset will still work reliably.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Bump to latest release candidate and drop 2 local patches that have been
upstreamed.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Generate a cpximg that is compatible with the cpximg loader in Compex' u-boot.
The cpximg loader can be started either by holding the reset button during power
up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept an image
appropriate for the board revision that is etched on the board (e.g. 6A04).
The image can be pushed using tftp:
tftp -v -m binary 192.168.1.1 -c put openwrt-ipq40xx-generic-compex_wpj428-squashfs-cpximg-6a04.bin
cpximg files can also be used with the sysupgrade utility in stock images.
(add SSH key in luci for root access)
In mkmylofw_32m, the calculation of the "partition size" has been preferred
to just padding the partition as this will result in less block transfers
during flashing (while the additional complexity is bearable).
Signed-off-by: Leon M. George <leon@georgemail.eu>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fixes following error uncovered while building malta/be on 5.4:
Package kmod-hwmon-sch5627 is missing dependencies for the following libraries:
watchdog.ko
That dependency was introduced in upstream via 2d8c7ff52c24
("hwmon/sch56xx: Depend on watchdog for watchdog core functions") in
v3.5.
The issue emerged in 5.4 because the kconfig symbol CONFIG_WATCHDOG_CORE
is now a tristate value. Previously it was a bool
Cc: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(drop the config-4.19 change. reword about the cause)
Hardware
--------
SoC: MediaTek MT7620A
RAM: 64MB
FLASH: 8MB SPI
WLAN: 2G: MediaTek MT7620A
5G: MediaTek MT7610EN
ETH: 1x 10/100/1000M (Atheros AR8035)
LED: RSSI (orange/green)
WiFi 2G (green)
WiFi 5G (green)
Power (green)
System (red / green)
BTN: Power
Reset
LED
WPS
Serial
------
P1 - Tx
P2 - Rx
P3 - GND
P4 - VCC
Pin 4 is the one closest to the LAN port.
MAC overview
------------
WAN *:4c uboot 0x1fc00
2.4 *:4c uboot 0x1fc00
5 *:4e uboot 0x1fc00 +2
Installation
------------
Web interface:
It is possible to upgrade to OpenWrt via the web interface. However, the
OEM firmware upgrade file is required and a tool to fix the MD5 sum of
the header. This procedure overwrites U-Boot and there is not failsafe /
recovery mode present! To prepare an image, you need to take the header
and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and
attach the factory image to it. Then fix the header MD5Sum1.
Serial/TFTP:
You can use initramfs for booting via RAM or flash the image directly.
Additional Notes:
If the web interface upgrade fails, you have to open your device and
attach serial console. Since the web upgrade overwrites the boot loader,
you might also brick your device.
In order to flash back to stock, the first header and U-Boot needs to be
stripped from the original firmware.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[change rssi LED labels]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This was available since kernel 5.4. The one provided in packages feed
will be considered deprecated and renamed to kmod-fs-exfat0.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(use name kmod-fs-exfat. use "@!(LINUX_4_4||LINUX_4_19)" for dependency)
This patch adds support for the 8devices Habanero development board.
Specs are:
CPU: QCA IPQ4019
RAM: DDR3L 512MB
Storage: 32MB SPI-NOR and optional Parallel SLC NAND(Some boards ship with it and some without)
WLAN1: 2.4 GHz built into IPQ4019 (802.11n) 2x2
WLAN2: 5 GHz built into IPO4019 (802.11ac Wawe-2) 2x2
Ethernet: 5x Gbit LAN (QCA 8075)
USB: 1x USB 2.0 and 1x USB 3.0 (Both built into IPQ4019)
MicroSD slot (Uses SD controller built into IPQ4019)
SDIO3.0/EMMC slot (Uses the same SD controller)
Mini PCI-E Gen 2.0 slot (Built into IPQ4019)
5x LEDs (4 GPIO controllable)
2x Pushbutton (1 is connected to GPIO, other to SoC reset)
LCD ZIF socket (Uses the LCD controller built into IPQ4019 which has no driver support)
1x UART 115200 rate on J18
2x breakout development headers
12V DC Jack for power
DIP switch for bootstrap configuration
Installation instructions:
Since boards ship with vendors fork of OpenWrt sysupgrade can be used.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit finally adds support for the built in SD/MMC controller in IPQ4019 SoC.
Controller is supported by the upstream SDHCI-MSM driver with a minor clock setting patch.
Patch is special to the IPQ4019 and cannot be upstreamed.
LDO and SDHCI node are upstreamed, and LDO node is awaiting to be accepted.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Also update the U-Boot BSP patch for I2SE Duckbill devices.
Run tested on I2SE Duckbill and Olimex OLinuXino Maxi boards.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Add missing kernel config symbol probably some dependency uncovered by
my local perf related and enabled kernel config options.
ARM PMU framework (ARM_PMU) [Y/n/?] y
Freescale i.MX8 DDR perf monitor (FSL_IMX8_DDR_PMU) [N/m/y/?] (NEW)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
I've added `set_blkcnt` environment variable which is needed for every
`mmc write` command as we need to always specify size in block count.
That `set_blkcnt` variable was previously present in the U-Boot's
default environment, but that needed patching U-Boot every time, so that
patch was dropped with 2020.01 version bump.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
U-Boot 2020.01 has changed names for same variables, adjust the
bootscript accordingly. Added boot_file variable as the default value is
zImage.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Update U-Boot to latest release, remove `100-wandboard-enable-fit.patch`
as FIT support was added in commit 5b8585825128 ("wandboard: Add FIT
image support").
Rework `110-mx6cuboxi-mmc-fallback.patch` into two patches as there was
new config option `CONFIG_SPL_FORCE_MMC_BOOT` added upstream which
should provide the same functionality as the previous patch hunk.
Moving Apalis towards generic distro_bootcmd.
Cc: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Removes one of the duplicate `gpio-keys` words found in the logs:
gpio-keys gpio-keys: gpio-keysdoes not support key code:143
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Adds into 4.19 backported kernel module from 5.1 for Sensirion SPS30
particulate matter sensor, for kernel 5.4 backported dependency fix.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Otherwise we would need to enable IIO_TRIGGERED_BUFFER symbol in all
kernels in order to be able to use any of the IIO modules which are
utilizing triggered buffer based data acquisition method.
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
