Commit Graph

23088 Commits

Author SHA1 Message Date
Adrian Schmutzler
65305cb448 kirkwood: use real model names for Linksys devices
This replaces the internal device names "Audi" and "Viper" with the
real model names, which a user would look for. This makes the
Linksys devices on this target consistent with the names recently
changed for mvebu based on the same idea.

As a consequence, the "viper" device definition is split into two
separate definitions with the correct names for both real models.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 15:03:43 +02:00
Tony Ambardar
a4856dab0d kernel: mips: restore missing MIPS32 cBPF JIT
Kernel v5.1 included an eBPF JIT for MIPS32 kernels, but problems were
discovered [1] and the changes later reverted in kernel v5.5 with commits:

  * f8fffebdea75 ("MIPS: BPF: Disable MIPS32 eBPF JIT")
  * 36366e367ee9 ("MIPS: BPF: Restore MIPS32 cBPF JIT")

Only the first of these was backported to LTS kernel 5.4, leaving cBPF
programs without a JIT and introducing a performance regression for any
such users e.g. libpcap, tcpdump, etc.

Restore cBPF performance by backporting the second commit above:
  * 070-v5.5-MIPS-BPF-Restore-MIPS32-cBPF-JIT.patch

[1] https://lore.kernel.org/bpf/20191205182318.2761605-1-paulburton@kernel.org/

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2020-07-31 13:42:14 +01:00
Adrian Schmutzler
664237deaa mvebu: fix alphabetic sorting in 02_network
This has been overlooked when removing solidrun,clearfog-a1 entry.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Adrian Schmutzler
e496eefccc mvebu: increase compat version for SolidRun ClearFog Base
When changing the Pro variant to DSA, the ethernet interface rename
script was dropped by all devices to keep them in sync:

  be309bfd74 ("mvebu: drop 06_set_iface_mac preinit script")

Therefore, network config will be broken after upgrade for the
Base variant as well. Increase the compat version and provide a
message to signal that to the users.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Adrian Schmutzler
090779b24e kirkwood: implement compatibility version for DSA migration
This implements the newly introduced compat-version to prevent
upgrade between swconfig and DSA for kirkwood.

Just define a compat version with minor increment and an appropriate
message for both image (in Makefile) and device (in base-files).

Since we never removed SUPPORTED_DEVICES for this target, we don't
have to add it back either.

Attention:

All users that already updated to the DSA versions in master will
receive the same incompatibility warning since their devices are still
"1.0" as far as fwtool can tell.
Those, and only those, can bypass the upgrade check by using force (-F)
without having to reset config again. In addition, the new version
string needs to be put into uci config manually, so the new fwtool
knows that it actually deals with a "1.1":

   uci set "system.@system[-1].compat_version=1.1"
   uci commit system

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Adrian Schmutzler
494f12c52d mvebu: implement compatibility version for DSA migration
This implements the newly introduced compat-version to prevent
upgrade between swconfig and DSA for mvebu.

Just define a compat version with minor increment and an appropriate
message for both image (in Makefile) and device (in base-files).

Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES
that have been removed in previous patches to prevent broken config.

Attention:

All users that already updated to the DSA versions in master will
receive the same incompatibility warning since their devices are still
"1.0" as far as fwtool can tell.
Those, and only those, can bypass the upgrade check by using force (-F)
without having to reset config again. In addition, the new version
string needs to be put into uci config manually, so the new fwtool
knows that it actually deals with a "1.1":

   uci set "system.@system[-1].compat_version=1.1"
   uci commit system

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Robinson Wu
84cb0f7ace ramips: add support for JS76x8 series DEV boards
This commit adds support for the Jotale JS76x8 series development boards.
These devices have the following specifications:

- SOC: MT7628AN/NN, MT7688AN, MT7628DAN
- RAM of MT7628AN/NN and MT7688AN: 64/128/256 MB (DDR2)
- RAM of MT7628DAN: 64 MB (DDR2)
- FLASH:8/16/32 MB (SPI NOR)
- Ethernet:3x 10/100 Mbps ethernet ports (MT76x8 built-in switch)
- WIFI:1x 2T2R 2.4 GHz Wi-Fi
- LEDs:1x system status green LED, 1x wifi green LED,
       3x ethernet green LED
- Buttons:1x reset button
- 1x microSD slot
- 4x USB 2.0 port
- 1x mini-usb debug UART
- 1x DC jack for main power (DC 5V)
- 1x TTL/RS232 UART
- 1x TTL/RS485 UART
- 13x GPIO header
- 1x audio codec(wm8960)

Installation via OpenWrt:

The original firmware is OpenWrt, so both LuCI and sysupgrade can be used.

Installation via U-boot web:

1. Power on board with reset button pressed, release it
   after wifi led start blinking.
2. Setup static IP 192.168.1.123/4 on your PC.
3. Go to 192.168.1.8 in browser and upload "sysupgrade" image.

Installation via U-boot tftp:
1. Connect to serial console at the mini usb, which has been connected to UART0
   on board (115200 8N1)
2. Setup static IP 192.168.1.123/4 on your PC.
3. Place openwrt-firmware.bin on your PC tftp server (192.168.1.123).
3. Connect one of LAN ports on board to your PC.
4. Start terminal software (e.g. screen /dev/ttyUSB0 115200) on PC.
5. Apply power to board.
6. Interrupt U-boot with keypress of "2".
7. At u-boot prompts:
   Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
   Input device IP (192.168.1.8) ==:192.168.1.8
   Input server IP (192.168.1.123) ==:192.168.1.123
   Input Linux Kernel filename (root_uImage) ==:openwrt-firmware.bin
8. board will download file from tftp server, write it to flash and reboot.

Signed-off-by: Robinson Wu <wurobinson@qq.com>
[add license to DTS files, fix state_default and reduce to the mimimum,
move phy0tpt trigger to DTS, drop ucidef_set_led_timer, fix network ports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
David Bauer
ced167d729 ramips: limit 5GHz channels for RAVPower RP-WD009
When selecting a channel below 100 on the 5GHz radio, the channel will
be detected as busy all the time.

Survey data from wlan1
	frequency:			5240 MHz [in use]
	channel active time:		165729 ms
	channel busy time:		158704 ms
	channel transmit time:		0 ms

Channels 100 and above work fine:

Survey data from wlan1
	frequency:			5500 MHz
	channel active time:		133000 ms
	channel busy time:		21090 ms
	channel transmit time:		0 ms

Limit the available channels, so users do not have the impression
their device is broken.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-30 22:33:53 +02:00
Petr Štetiar
e9f7923a1d treewide: mark devices as BROKEN instead of commenting out
This adds the newly introduced BROKEN flag to a bunch of devices
that previously just had TARGET_DEVICES commented out. By this, we
can select them in make menuconfig when BROKEN developer config option
is selected, instead of having to edit the code.

In contrast to DEFAULT := n, this is meant to cover devices that
don't boot or don't compile at all.

ath25: np25g, wpe53g
  both disabled during kernel bump 3.18->4.4 without reason given
  f89a20a89a ("ath25: update kernel from 3.18 to 4.4")

bcm53xx: linksys-ea6300-v1, linksys-ea9200, linksys-ea9500
  broken due to insufficient/broken TRX support
  55ff15cfd5 ("bcm53xx: disable building Linksys EA6300 V1 image")
  cd0f9900a4 ("bcm53xx: parepare for building more Linksys images")

bcm63xx: tplink-archer-c5-v2, tplink-archer-c9-v1
  disabled when kernel 5.4 support was added, probably broken
  50c6938b95 ("bcm53xx: add v5.4 support")

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[limit to subset of devices, use BROKEN, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-30 21:49:22 +02:00
Petr Štetiar
504000d520 treewide: use DEFAULT := n to disable non-broken devices
This uses DEFAULT := n on a bunch of devices that previously were
"disabled" by commenting out TARGET_DEVICES. This will allow to
build them without having to modify the code, but they will not
be selected for default build or buildbots.

The change is applied to all devices that are not "broken", but suffer
from image site limitations or similar, or have been added in the past
but never confirmed to run on the device properly:

at91: at91-q5xr5:
  kernel image too big
  31aeae0774 ("at91: do not build image for at91-q5xr5")

bcm47xx: asus-rt-ac66u:
  disabled since it was added in 2015
  69aefc771f ("brcm47xx: build images for Asus devices")

bcm47xx: netgear-wndr3400-vcna, netgear-wnr3500u, netgear-wnr3500-v2-vc
  added disabled in 2012, but never confirmed to work on devices
  5dec9dd3b2 ("brcm47xx: add code to generate images for some netgear
    devices")

bcm53xx: netgear-r8500
  added disabled: "start working on Netgear R8500"
  3b76c7cf0b ("bcm53xx: start working on Netgear R8500")

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[limit to subset of devices, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-30 21:48:38 +02:00
Adrian Schmutzler
bf5c56ba57 ath79: cosmetic fixes for partition node of D-Link DIR-825 B1
Make the node name match the reg property and remove the unused
DT label.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-30 21:43:56 +02:00
Daniel Golle
d1a8217d87 kernel: clean-up build-configurable kernel config symbols
Don't explicitely disable options in target/linux/generic/config-* if
they are already controlled in config/Config-kernel.in.
Add a bunch of new symbols  and prepare defaults for using only unified
hierarchy (ie. cgroup2). Update symbol dependencies while at it

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-07-30 16:59:47 +01:00
Luochongjun
68ac3f2cdd ath79: add support for gl-e750
The gl-e750 is a portable travel router that gives you safe access to
the internet while traveling.

Specifications:
- SoC: Qualcomm Atheros AR9531 (650MHz)
- RAM: 128 MB DDR2
- Flash: 16 MB SPI NOR (W25Q128FVSG) + 128 MB SPI NAND (GD5F1GQ4UFYIG)
- Ethernet: 10/100: 1xLAN
- Wireless: QCA9531 2.4GHz (bgn) + QCA9887 5GHz (ac)
- USB: 1x USB 2.0 port
- Switch: 1x switch
- Button: 1x reset button
- OLED Screen: 128*64 px

MAC addresses based on vendor firmware:
LAN *:a0 art 0x0
2.4GHz *:a1 art 0x1002
5GHz *:a2 art calculated from art 0x0 + 2

Flash firmware:
Since openwrt's kernel already exceeds 2MB, upgrading from the official
version of GL-inet (v3.100) using the sysupgrade command will break the
kernel image. Users who are using version 3.100 can only upgrade via
uboot. The official guidance for GL-inet is as follows:
https://docs.gl-inet.com/en/3/troubleshooting/debrick/

In the future, GL-inet will modify the firmware to support the sysupgrade
command, so users will be able to upgrade directly with the sysupgrade
command in future releases.

OLED screen control:
OLED controller is connected to QCA9531 through serial port, and can send
instructions to OLED controller directly through serial port.
Refer to the links below for a list of supported instructions:
https://github.com/gl-inet/GL-E750-MCU-instruction

Signed-off-by: Luochongjun <luochongjun@gl-inet.com>
[fix alphabetic sorting in 10-fix-wifi-mac, drop check-kernel-size]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 20:49:48 +02:00
Adrian Schmutzler
6da5356195 lantiq: disable default build for devices with 4M flash
It has been decided that the 19.07 release will be last one to include
4/32 devices.

This disables default build for all devices with 4M flash on lantiq.
Note that this will affect _all_ devices for amazonse ("ase") and
xway_legacy subtarget.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 12:08:16 +02:00
Adrian Schmutzler
55e2d5eb3b ath79: disable default build for devices with 4M flash
It has been decided that the 19.07 release will be last one to include
4/32 devices.

This disables default build for the remaining devices with 4M flash
on ath79. Note that this will leave exactly one enabled device for
ath79/tiny subtarget, PQI Air-Pen, which was moved there due to
kernel size restrictions.

All 4M TP-Link devices have already been disabled in
8819faff47 ("ath79: do not build TP-Link tiny images by default")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 12:08:16 +02:00
Adrian Schmutzler
01a3e891d7 ath79: reorganize common image definitions for Netgear
Netgear currently has a special definition for tiny devices, which
is only used by two devices. Despite, it sets ups the IMAGE/default
definition individually for all devices, although there is actually
only one exception.

This merges the common parts into a single netgear_generic definition
(in contrast to netgear_ath79_nand), and adjusts the individual
definitions accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 12:08:16 +02:00
David Bauer
c5360894dc rockchip: enable rockchip-thermal
Enable the rockchip-thermal driver to allow reading the temperature of
the SoC.

Tested on NanoPi R2S

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-29 01:40:20 +02:00
David Bauer
7a4fc8906c rockchip: distribute net interrupts
This adds a hotplug script for distributing interrupts of eth0 and eth1
across different cores. Otherwise the forwarding performance between
eth0 and eth1 is severely affected.

The existing SMP distribution mechanic in OpenWrt can't be used here, as
the actual device IRQ has to be moved to dedicated cores. In case of
eth1, this is in fact the USB3 controller.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
5a57a1ac1f arm64: dts: rockchip: Add txpbl node for RK3399/RK3328
Some rockchip SoCs like the RK3399 and RK3328 exhibit an issue
where tx checksumming does not work with packets larger than 1498.

The default Programmable Buffer Length for TX in these GMAC's is
not suitable for MTUs higher than 1498. The workaround is to disable
TX offloading with 'ethtool -K eth0 tx off rx off' causing performance
impacts as it disables hardware checksumming.

This patch sets snps,txpbl to 0x4 which is a safe number tested ok for
the most popular MTU value of 1500.

For reference, see https://lkml.org/lkml/2019/4/1/1382.

Signed-off-by: Carlos de Paula <me@carlosedp.com>
Link: https://lore.kernel.org/r/20200218221040.10955-1-me@carlosedp.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
6242ac4735 rockchip: enable LAN LED configuration
This enables the LEDs on the LAN interfaces.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
b7a9a183fb rockchip: add NanoPi R2S support
Hardware
--------
RockChip RK3328 ARM64 (4 cores)
1GB DDR4 RAM
2x 1000 Base-T
3 LEDs (LAN / WAN / SYS)
1 Button (Reset)
Micro-SD slot
USB 2.0 Port

Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.

MAC-address
-----------
The vendor code supports reading a MAC address from an EEPROM connected
via i2c0 of the SoC. The EEPROM (address 0x51) should contain the MAC
address in binary at offset 0xfa. However, my two units didn't come with
such an EEPROM soldered on. The EEPROM should be placed between the SoC
and the GPIO pins on the board. (U10)

Generating rendom MAC addresses works around this issue. Otherwise, all
boards running the same image have identical MAC addresses.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
b72f7c64a4 rockchip: allow for multiple boot-scripts
Add support for select a bootscript depending on the device built. This
is necessary, as the FriendlyARM NanoPi R2S needs a different bootcmd in
order to produce output on the debug UART.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
Adrian Schmutzler
bcd7a0c095 arc770: update kernel version to 5.4
Update config with make kernel_oldconfig and copy/refresh patch.

Add CONFIG_WATCHDOG_CORE=y to fix the following error as done for
several targets already:

 Package kmod-hwmon-sch5627 is missing dependencies for the following
 libraries:
 watchdog.ko

Directly switch to kernel 5.4.

This patch is compile-tested only. However, the target is essentially
pure upstream with a single patch, and it has been reported that
kernel 5.4 has been run on this target successfully already.

Note that in my local tests building with all packages/kmods failed
since openvswitch selects libunwind, which doesn't build for arc with
the following error:

checking if we should build libunwind-ptrace... yes
checking if we should build libunwind-setjmp... yes
checking for build architecture... x86_64
checking for host architecture... arc
checking for target architecture... arc
checking for target operating system... linux-gnu
checking for ELF helper width... configure: error: Unknown ELF target: arc
make[3]: *** [Makefile:65: /data/openwrt/build_dir/target-arc_arc700_uClibc/
   libunwind-1.3.1/.configured_68b329da9893e34099c7d8ad5cb9c940] Error 1

Deselecting all kmod-openvswitch* packages will have the build run through.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 20:15:10 +02:00
Adrian Schmutzler
88689da65f lantiq: fix cosmetic issues with partition offsets and sizes
This fixes a few cosmetic issues with partition offset and size
that are inconsistent probably due to copy/pasting.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 13:02:47 +02:00
Josh Bendavid
11bff24b3e ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.

Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
        WiFi 5G (white), USB 3.0 (white)

Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips

Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
  button, then re-plug it. Keep the reset button pressed until the power
  LED starts flashing orange, manually assign a static IP address under
  the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1

* Some modern browsers may have problems flashing via the Recovery GUI,
  if that occurs consider uploading the firmware through cURL:

    curl -v -i -F "firmware=@file.bin" 192.168.0.1

MAC addresses:

lan   factory 0xe000     *:EB (label)
wan   factory 0xe006     *:EE
2.4   factory 0xe000 +1  *:EC
5.0   factory 0xe000 +2  *:ED

Seems like vendor didn't replace the dummy entrys in the calibration data.

Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 12:37:07 +02:00
Adrian Schmutzler
8126e572dd imx6: use device-tree compatible for board name
In imx6, we currently use the model from DTS to derive a board name
manually in /lib/imx6.sh.

However, if we have individual DTS files anyway, we can exploit
generic 02_sysinfo and use the compatible as board name directly.

While at it, remove the wildcards from /lib/upgrade/platform.sh as
these might make code shorter, but are quite unpleasant when grepping
for a specific device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 12:10:45 +02:00
Adrian Schmutzler
0f3c3a5fb2 layerscape: harmonize device strings
OpenWrt lately has harmonized device (definition) names to the
pattern vendor_model to improve overall consistency, also with
other values like the DTS compatible.

This patch applies that scheme to the layerscape target.

Since this (intentionally) creates a bigger overlap between DTS names,
compatible, and device definition name, it also moves DEVICE_DTS and
SUPPORTED_DEVICES definitions to the Device/Default blocks.

Apart from that, it also modifies several packages to use consistent
naming in order to keep the $(1) file references working.

While at it, remove one layer of complexity for the setup in
tfa-layerscape package.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 12:06:52 +02:00
Adrian Schmutzler
a1eb2c4633 mvebu: only disable WRT1900AC v1 and WRT32X for buildbots
Use "DEFAULT := n" to only disable devices for buildbots, but
keep them available for manual build.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 11:05:25 +02:00
Jo-Philipp Wich
ac9730c495 mvebu: disable WRT1900AC v1 and WRT32X images for now
The kernel appears to have grown too large, breaking the build for the
entire target.

Disable the affected images for now until the situation is dealt with.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-07-26 18:58:22 +02:00
David Woodhouse
b36422b914 mediatek: mt7623: add full system image for UniElec U7623
This adds a full eMMC image including U-Boot, which means that the
kernel can inherit the true RAM size detected by the preloader.

As implemented in previous commits, sysupgrade to this image from
the legacy layout (and via that, from the vendor-installed image)
is supported.

Rename the legacy image for the 512MiB board, for clarity.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:08:31 +08:00
David Woodhouse
1113dcab05 mediatek: mt7623: rename gen_banana_pi_img.sh → gen_mtk_mmc_img.sh
As I buy more hardware and continue to work on consolidation, This will
apply to a lot of MediaTek platforms; rename it accordingly.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:08:21 +08:00
David Woodhouse
f5cebbe2e4 mediatek: mt7623: make gen_banana_pi_img.sh more generic
This actually covers fairly much all the MediaTek platforms; they
only have different images because they don't include the preloader
and U-Boot, and rely on preinstalled stuff from the vendor.

So this script can slowly take over the world as we complete the
support for various other platforms, starting with UniElec U7623…

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:08:21 +08:00
David Woodhouse
5787684cb4 mediatek: mt7623: add scatter file for unbricking with SP Flash Tool
Many MediaTek SoCs can be unbricked by using the SP Flash Tool from
http://spflashtool.com/ along with a "scatter list" file, which is
just a text file listing which image gets loaded where.

We use a trivial partition layout for the tool, with the whole eMMC
image as a single "partition", which means users just need to unzip
the sysupgrade image. Doing the real partition layout would be overly
complex and would require the individual partitions to be shipped
as artifacts — or users to extract them out of the sysupgrade image
just for the tool to put them adjacent to each other on the eMMC
anyway.

The tool does require a copy of the preloader in order to operate,
even when it isn't flashing the preloader to the eMMC boot region.
So drop that into the bin directory as an artifact too.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:07:52 +08:00
Chuanhong Guo
65fc47cac5 mediatek: mt7623: build lzma fit for bpi-r2
bpi-r2 images are shipped with mainline u-boot which can extract lzma
with no problem.
remove custom kernel recipe to build lzma fit image instead of
uncompressed fit with zboot.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-07-26 17:04:49 +08:00
David Woodhouse
29fa5526a2 mediatek: mt7623: prepare for full sysupgrade support on UniElec U7623
An upcoming commit will add a full system image for U7623 which will
contain the MBR partition table and U-Boot too.

That contrasts with the current image which only owns the eMMC from
sector 0xa00 onwards, and must start with a legacy uImage.

Prepare for sysupgrade to the new images, and cope with the fact that
the recovery partition will be /dev/mmcblk0p2 instead of /dev/mmcblk0p1
after the upgrade.

This commit could potentially be backported to 19.07 to allow for direct
sysupgrade to the new image layout.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:36 +08:00
David Woodhouse
7a1eaa446b mediatek: mt7623: increase flexibility of finding recovery partition
I'm about to change the layout of the images for UniElec U7623 so make it
find the recovery partition based on which the root partition is too.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:36 +08:00
David Woodhouse
ff8cc137fb mediatek: mt7623: fix Ethernet setup for TRGMII mode
This fixes the TX performance issues seen on MT7623 boards.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:36 +08:00
David Woodhouse
be3c8f8b2b mediatek: fix Ethernet support on UniElec U7623
The definition of the switch in the device-tree was not correct. Make it
look more like the Banana Pi R2, which works.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:35 +08:00
David Woodhouse
6eb63019af mediatek: mt7623: fix sysupgrade from vendor OpenWrt on UniElec U7623
This board ships with an ancient 14.07-based OpenWrt using block2mtd, and
the MBR partition table contains nonsense.

It is possible to sysupgrade to an upstream OpenWrt image, but the
legacy layout of the OpenWrt images start at 0xA00 in the eMMC, with
a raw uImage. The legacy OpenWrt image doesn't "own" the beginning
of the device, including the MBR and U-Boot.

This means that when a user upgrades to upstream OpenWrt, it doesn't
boot because it can't find the right partitions. So hard-code them on
the kernel's command line using CONFIG_CMDLINE_PARTITION (for block).

Additionally, the vendor firmware doesn't cope with images larger than
about 36MiB, because it only overwrites the contents of its "firmware"
MTD partition. The current layout of the legacy image wastes a lot of
space, allowing over 32MiB for the kernel and another 10MiB for the FAT
recovery file system which is only created as 3MiB. So pull those in
to allow 4¾ MiB for the kernel, 3MiB for recovery, and then we have over
20MiB for the root file system.

This doesn't affect the new images which ship with a full eMMC image
including a different MBR layout and a partition for U-Boot, because
our modern U-Boot can actually pass the command line to the kernel, and
the built-in one doesn't get used anyway.

Tested by upgrading from vendor OpenWrt to the current legacy image,
from legacy to itself, to the previous legacy layout, and then to
finally the full-system image.

This commit probably wants backporting to 19.07, which also doesn't
install over the vendor OpenWrt and doesn't even have a full-system
installation option.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:35 +08:00
David Woodhouse
ea9ef8c945 mediatek: mt7623: add explicit console= to U7623 kernel
The bootloader for legacy builds can't set it, so we end up unable to
log in on the serial port.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:35 +08:00
Leon M. George
15f585afc5 ath79: add support for Compex WPJ563
Specifications:

SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 Gigabit ethernet ports
3×3 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 24V passive or 36V-56V passive with optional IEEE 802.3af/at
USB 3.0 header

Installation:

To install, either start tftp in bin/targets/ath79/generic/ and use
the u-boot prompt over UART:

tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj563-squashfs-sysupgrade.bin
erase 0x9f680000 +1
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
boot

The cpximg file can be used with sysupgrade in the stock firmware (add
SSH key in luci for root access) or with the built-in cpximg loader.
The cpximg loader can be started either by holding the reset button
during power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.

For example, if the board is labelled '7A02':

tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj563-squashfs-cpximg-7a02.bin

MAC addresses:

<&uboot 0x2e010>  *:71  (label)
<&uboot 0x2e018>  *:72
<&uboot 0x2e020>  *:73
<&uboot 0x2e028>  *:74

Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.

Signed-off-by: Leon M. George <leon@georgemail.eu>
2020-07-26 02:14:45 +02:00
Aleksander Jan Bajkowski
f8ea7c53fd lantiq: xrx200: disable unused switch and phy
xrx200 has a 6 port built-in switch with 2 integrated PHY. None of the
xrx200 router uses external switch. Most boards use integrated or Lantiq
(Intel) PEF7071 PHY. Only some FritzBox routers use AT803X PHY and
VGV7510KW22 use ICPLUS PHY. Other unused PHY drivers may be removed.

This patch enables these symbols only on xway and xway_legacy subtargets:
 - CONFIG_PSB6970_PHY (Driver for PHY in PSB6970 - 7 port FE Switch)
 - CONFIG_RTL8366RB_PHY (Driver for PHY in RTL8366 - 6 port GE Switch)
 - CONFIG_RTL8366_SMI (Driver for RTL8366 - 6 port GE Switch)

Reduces image size by 7.3kB.

Continuation of 58a6f06978 (PR: #2983)

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[fix sorting in config files, small fix in commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-26 02:14:38 +02:00
Adrian Schmutzler
739d282c2f mediatek: remove condition in Device/Default
The current condition with part of the variables set dependent on
the subtarget in Device/Default isn't really nice to read and also
defeats the purpose of having a default node.

This removes the special settings for mt7623 and moves them to the
individual devices, which is not much of a problem as there are
actually just two of them and they partly use different settings
anyway.

While at it, slightly adjust the order of variables and wrap some
long lines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-25 23:19:19 +02:00
Bjoern Dobe
d38d345c72 ath79: mikrotik: use base mac on lan for RBwAPG-5HacT2HnD
The Mikrotik RBwAPG-5HacT2HnD has only a single ethernet interface
(lan), and the vendor uses the base (label) MAC address for it.

Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>
[commit title/message improvement]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-25 22:01:34 +02:00
Sungbo Eo
ab78694fe8 treewide: rename POWER_ON_STRIP register
AR8327 datasheet[1] calls the register at address 0x0010
"Power-on Strapping Register". As it has nothing to do with "strip",
let's rename it to "POWER_ON_STRAP" to make it easier to grasp.

[1] https://lafibre.info/images/doc/201106_spec_AR8327.pdf

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-25 21:50:50 +02:00
John Thomson
8484d6da1e ramips: remove non-existant poe_passthrough for RouterBOARD 750Gr3
This 750gr3 GPIO17 switch was added based on vendor source,
but only the 760iGS (which shares the rbsysfs board identifier)
device has the physical wiring. The 750Gr3 actually does not
support PoE out.

Apart from that, note that the gpio base (480) would have required
this GPIO to be referenced as 497 if it was kept.

Fixes: 6ba58b7b02 ("ramips: cleanup the RB750Gr3 support")

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-25 21:41:07 +02:00
Davide Fioravanti
92780d80ab ramips: add support for Winstars WS-WN583A6
The Winstars WS-WN583A6 is a wireless repeater with 2 gigabit ethernet
ports. Even if mine is branded as "Gemeita AC2100", the sticker on the
back says WS-WN583A6. So I will refer to it as Winstars WS-WN583A6.
Probably the real product name is the Wavlink WL-WN583A6 because of
the many references to Wavlink in the OEM firmware and bootlog.

Hardware
--------
SoC:   Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM:   128MB
FLASH: 8MB NOR (GigaDevice GD25Q64B)
ETH:   2x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
  - 2.4GHz: 1x MT7603E (2x2:2)
  - 5GHz:   1x MT7615E (4x4:4)
  - 6 internal antennas
BTN:
  - 1x Reset button
  - 1x WPS button
  - 1x ON/OFF switch (working but unmodifiable)
  - 1x Auto/Schedule switch (working but unmodifiable. Read Note #3)
LEDS:
  - 1x White led
  - 1x Red led
  - 1x Amber led
  - 1x Blue led
  - 2x Blue leds (lan and wan port status: working but unmodifiable)
UART:
  - 57600-8-N-1

Everything works correctly.

Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.

Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on M83A6.V5030.191210 firmware version.

1) Go to http://192.168.10.1/webcmd.shtml

2) Type the following line in the "Command" input box:
	mkdir /etc_ro/lighttpd/www/dev; for i in /dev/mtd*ro; do dd if=${i} of=/etc_ro/lighttpd/www${i}; done

3) Click "Apply"

4) After few seconds, in the textarea should appear this output:
		16384+0 records in
	16384+0 records out
	8388608 bytes (8.0MB) copied, 4.038820 seconds, 2.0MB/s
	384+0 records in
	384+0 records out
	196608 bytes (192.0KB) copied, 0.095180 seconds, 2.0MB/s
	128+0 records in
	128+0 records out
	65536 bytes (64.0KB) copied, 0.032020 seconds, 2.0MB/s
	128+0 records in
	128+0 records out
	65536 bytes (64.0KB) copied, 0.031760 seconds, 2.0MB/s
	15744+0 records in
	15744+0 records out
	8060928 bytes (7.7MB) copied, 3.885280 seconds, 2.0MB/s
	dd: can't open '/dev/mtd5ro': No such device
	dd: can't open '/dev/mtd6ro': No such device
	dd: can't open '/dev/mtd7ro': No such device

   Excluding the "X.XXXXXX seconds" part, you should get the same
   exact output. If your output doesn't match mine, stop reading
   and ask for help in the forum.

5) Open the following links to download the partitions of the OEM FW:
	http://192.168.10.1/dev/mtd0ro
	http://192.168.10.1/dev/mtd1ro
	http://192.168.10.1/dev/mtd2ro
	http://192.168.10.1/dev/mtd3ro
	http://192.168.10.1/dev/mtd4ro

   If one (or more) of these files weight 0 byte, stop reading and ask
   for help in the forum.

6) Store these downloaded files in a safe place.

7) Reboot your router to remove any temporary file from your router.

Installation
------------
Flash the initramfs image in the OEM firmware interface.
When openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.

Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) The "System Command" page allows to run every command as root.
   For example you can use "dd" and "nc" to backup the OEM firmware.
   PC (SERVER):
	nc -l 5555 > ./mtdXro
   ROUTER (CLIENT):
	dd if=/dev/mtdXro | nc PC_IP_ADDRESS 5555

2) The OEM web interface accepts only images containing the string
   "WN583A6" in the filename.
   Currently the OEM interface accepts only the initramfs image
   probably because it checks if the ih_size in the image header is
   equal to the whole image size (instead of the kernel size)
   Read more here:
   https://forum.openwrt.org/t/support-for-strong-1200/22768/19

3) The white led (namely "Smart Night Light") can be controller by the
   user only if the side switch is set to "Schedule" otherwise it will
   be activated by the light condition (there is a photodiode on the
   top side of the router)

4) Router mac addresses:

   LAN		XX:XX:XX:XX:XX:8F
   WAN		XX:XX:XX:XX:XX:90
   WIFI 2G	XX:XX:XX:XX:XX:91
   WIFI 5G	XX:XX:XX:XX:XX:92

   LABEL	XX:XX:XX:XX:XX:91

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove chosen node, fix whitespace]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-25 21:04:11 +02:00
Adrian Schmutzler
1e55df2e41 oxnas: use vendor_model scheme for ox810se
Most newer targets have been converted to consistently use
vendor_model scheme for device definitions/image names, ox820 is
using it as well, so let's just convert ox810se for consistency.

While at it, use generic setup for DEVICE_DTS and add SUPPORTED_DEVICES.
The latter have been introduced for ox820 already in
cf7896117b ("oxnas: enable image metadata by setting SUPPORTED_DEVICES")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-25 21:04:11 +02:00
Hauke Mehrtens
64de3076c3 lantiq: Fix warning in SPI driver
This fixes a warning in the SPI driver at bootup. This warning is seen
in kernel 5.4 on lantiq deives.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-23 23:39:56 +02:00
Phi Nguyen
eda9751d86 ipq40xx: support reset button for WPJ419
Compex WPJ419 has a reset button on a GPIO pin.

Signed-off-by: Phi Nguyen <phind.uet@gmail.com>
2020-07-23 12:56:58 +02:00
Adrian Schmutzler
b057862e24 Revert "ramips: fix flash layout for TP-Link TL-WR841N v14"
This reverts commit 1623defbdb.

As already stated in the reverted patch, the OEM firmware will
properly recreate the config partition if it is overwritten by
OpenWrt.

The main reason for adding the partition was the image size
restriction imposed by the 0x3d0000 limitation of the TFTP
flashing process. Addressing this by shrinking the firmware
partition is not a good solution to that problem, though:

1. For a working image, the size of the content has to be smaller
   than the available space, so empty erase blocks will remain.

2. Conceptually, the restriction is on the image, so it makes sense
   to implement it in the same way, and not via the partitioning.
   Users could e.g. do initial flash with TFTP restriction with
   an older image, and then sysupgrade into a newer one, so TFTP
   restriction does not apply.

3. The (content) size of the recovery image is enforced to 0x3d0000
   by the tplink-v2-image command in combination with
   TPLINK_FLASHLAYOUT (flash layout in mktplinkfw2.c) anyway.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-22 18:59:44 +02:00
Adrian Schmutzler
0a5d74fa68 arc770: use generic 02_sysinfo
Currently arc770 sets a board name from compatible for no apparent
reason. Just use the compatible directly instead.

This theoretically removes a board name "generic" when no compatible
was present, however, there is no case where this "generic" board
name was actually used.

This also fixes an issue where snps,axs101 would not have been
properly detected anyway, as its case was not set up syntactically
correct.

Fixes: 576621f1e3 ("linux: add support of Synopsys ARC770-based boards")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-22 18:28:09 +02:00
Adrian Schmutzler
3c190ef112 archs38: use generic 02_sysinfo
Currently archs38 sets a board name from compatible for no apparent
reason. Just use the compatible directly instead.

This theoretically removes a board name "generic" when no compatible
was present, however, there is no case where this "generic" board
name was actually used.

This also fixes an issue where snps,axs103 would not have been
properly detected anyway, as its case was not set up syntactically
correct.

Fixes: 73015c4cb3 ("linux: add support of Synopsys ARCHS38-based boards")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-22 18:28:09 +02:00
David Bauer
9662b9d688 ramips: switch MT7620 subtarget to 5.4
MT7620 seems to work fine with kernel 5.4. Set the default kernel
version to 5.4 to bring this to a broader audience.

Tested on Archer C2 v1 / Archer C20i

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-22 17:20:38 +02:00
David Bauer
4cd5ce5a7f ramips: increase SPI frequency for MT7620 Archer
Increase the SPI frequency for the MT7620 based TP-Link Archer
series to 30MHz.

TP-Link uses different SPI flash chips for the same board
revision, so be conservative to not break boards with a
different chip. 30MHz should be well supported by all chips.

Tested on Archer C2 v1 (GD25Q64B) and Archer C20i (W25Q64FV).

Archer C20i (before)
====================
root@OpenWrt:~# time dd if=/dev/mtd1 of=/tmp/test.bin bs=64k
122+0 records in
122+0 records out
real	0m 15.30s
user	0m 0.00s
sys	0m 15.29s

Archer C20i (after)
===================
root@OpenWrt:~# time dd if=/dev/mtd1 of=/tmp/test.bin bs=64k
122+0 records in
122+0 records out
real	0m 5.99s
user	0m 0.00s
sys	0m 5.98s

Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-22 17:20:24 +02:00
David Bauer
9a9cdc65c4 ath79: re-enable image generation for GL-AR750S
The bootloader only writes the first 2MB of the image to the NOR flash
when installing the NAND factory image. The bootloader is capable of
booting larger kernels as it boots from the memory mapped SPI flash.

Disable the NAND factory image. The NAND can be bootstrapped by writing
the NAND initramfs image using the NOR upgrade method in the bootloader
web-recovery and sysupgrading from there. The NOR variant is not
affected.

Also refactor the partition definitions in the DTS to make them less
annoying to read.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-22 17:18:55 +02:00
Adrian Schmutzler
5e86877f36 ath79: correctly define WiFi switch for TL-WR841ND v8
The TL-WR841ND v8 feature a WiFi switch instead of a button.
This adds the corresponding input-type to prevent booting into
failsafe regularly.

This has been defined correctly in ar71xx, but was overlooked
when migrating to ath79. In contrast, the TL-WR842ND v2, which
has the key set up as switch in ar71xx, actually has a button.
The TL-MR3420 v2 has a button as well and is set up correctly
for both targets. (Information based on TP-Link user guide)

Note:

While looking into this, I found that support PR for TL-MR3420 v2
switched reset button to ACTIVE_HIGH. However, the other two
device still use ACTIVE_LOW. This seems strange, but I cannot
verify it lacking the affected devices.

Fixes: FS#2733
Fixes: 9601d94138 ("add support for TP-Link TL-WR841N/ND v8")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-21 12:02:35 +02:00
Adrian Schmutzler
42dc5c2a3f ramips: improve LED support for D-Link DIR-615 D series
This patch adds a trigger for the WAN LED and enhances support for
the WiFi LED by enabling activity indication.

This is based on bug report feedback (see reference below).

While at it, update the LED node names in DTS file.

Fixes: FS#732

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-21 11:59:17 +02:00
Adrian Schmutzler
05c74e4000 omap: derive DEVICE_DTS from device name
In most cases the DEVICE_DTS name can be derived easily from the
node name, so let's do this to enforce harmonized names where
possible.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-21 11:57:22 +02:00
Adrian Schmutzler
eff0a0e39e apm821xx: derive DEVICE_DTS from device name
The DEVICE_DTS variable always matches the device definition name,
just with "_" replaced by "-". Thus, create a DEVICE_DTS definition
in Device/Default and drop all the individual statements.

If necessary in the future, local DEVICE_DTS will still overwrite
that default.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-21 11:56:35 +02:00
Adrian Schmutzler
a2fee73e27 bcm47xx: fix switch setup for Linksys WRT610N v2
WRT610N V2 is not detected by the initial network configuration script.
The switch remains unconfigured and wlan/lan vlans are not created.

This adds the correct setup for the device.

Fixes: FS#1869

Suggested-by: Alessandro Radicati
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-21 11:55:31 +02:00
Adrian Schmutzler
683193cfb7 layerscape: fix indent
Fix indent to be consistent with the rest of the file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-21 11:51:51 +02:00
Nelson Cai
6269f10ea4 ramips: fix network setup for Ubiquiti ER-X/ER-X-SFP
The function name ucidef_set_interface_lan_wan does not exist,
use the proper name by adding an "s" and thereby fix network
setup on these devices.

Fixes: 22468cc40c (ramips: erx and erx-sfp: fix missing WAN interface)

Signed-off-by: Nelson Cai <niphor@gmail.com>
[commit message/title facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-20 17:16:47 +02:00
Dustin Gathmann
d5a148f5c8 lantiq/xrx200: make WLAN button responsive on Fritzbox 7360 & 7362
Pressing the 'WLAN' button should enable/disable wireless activity.
Currently, the button is mapped to the KEY_WLAN, which will not
have this effect.
This patch changes the mapping of the WLAN button, so a button
press will emit an action for the 'rfkill' key instead of 'wlan'.
Apparently, this is what stock OpenWRT expects.

This fix is analogous to the preceding patch for Fritzbox 3370.

Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
2020-07-20 00:58:30 +02:00
Dustin Gathmann
0ee30adb46 lantiq/xrx200: fix WLAN button actions for Fritzbox 3370
The WLAN button actions are reversed, i.e. pressing the button emits a
'released' action, and vice versa.
This can easily be checked by adding
logger -t button_action "$BUTTON $ACTION"
as the second line of /etc/rc.button/rfkill, and using logread to read
the events (assuming the preceding patch has been applied).
Defining the GPIO as ACTIVE_LOW corrects this behavior.

Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
2020-07-20 00:58:30 +02:00
Dustin Gathmann
a53bf63756 lantiq/xrx200: make WLAN button responsive on Fritzbox 3370
Pressing the 'WLAN' button should enable/disable wireless activity.
However, on the Fritzbox 3370 this doesn't have an effect.
This patch changes the mapping of the physical WLAN button, so a button
press will emit an action for the 'rfkill' key instead of 'wlan'.
Apparently, this is what stock OpenWRT expects, and also what is
implemented for most other devices.

Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
2020-07-20 00:58:30 +02:00
Alexander Müller
1623defbdb ramips: fix flash layout for TP-Link TL-WR841N v14
The config partition was missing from the flash layout of the device.

Although the stock firmware resets a corrupted config partition to the
default values, the TFTP flash with an image bigger than 0x3d0000 will
truncate the image as the bootloader only copies 0x3d0000 bytes to flash
during TFTP flashing.

Fixed by adding the config partition and shrinking the firmware
partition.

Fixes: 3fd97c522b ("ramips: add support for TP-Link TL-WR841n v14")

Signed-off-by: Alexander Müller <donothingloop@gmail.com>
2020-07-19 02:01:06 +02:00
Adrian Schmutzler
2e4626ae77 ramips: remove incorrect mtd-eeprom for TP-Link TL-WR841N v14
The factory partition on this device is only 64k in size, so having
mediatek,mtd-eeprom = <&factory 0x10000> would place the EEPROM data
after the end of the flash. As can be verified against the TP-Link
GPL sources, which contain the EEPROM data as binary blob, the actual
address for the EEPROM data is 0x0.

Since 0x0 is default for MT7628, the incorrect line is just removed.

This error is the reason for the abysmal Wifi performance that people
are complaining about for the WR841Nv14.

Fixes: 3fd97c522b ("ramips: add support for TP-Link TL-WR841n v14")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-19 02:01:06 +02:00
David Bauer
612d5282b5 ramips: don't create switch config for VIXMINI
Don't create UCI switch config for the GL.iNet microuter-N300 and
VIXMINI. These devices only have a single LAN port.
Creating the switch config makes usage of VLANs more complicated,
as they would have to be configured on the MAC as well as the "switch".

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-18 22:12:19 +02:00
Adrian Schmutzler
b78a266888 lantiq: move 01_led_migration script to subtargets
Split the /etc/uci-defaults/01_led_migration scripts into subtargets
as already done for most of the other base-files.

While this introduces a minor amount of code duplication, it still
is considered an improvement, as device-specific settings are kept
together in the subtargets' base-files and the script at hand can be
removed entirely for two of the subtargets not needing it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-17 12:14:32 +02:00
Martin Schiller
4d8552c265 lantiq: move dsl related base-files into own package
It does not make sense to install this components on lantiq systems
where the dsl subsystem is not needed/used.

This also makes it possible to use the files also on other targets.
(hopefully ipq401x / FritzBox 7530 in the near future)

Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
2020-07-17 12:14:32 +02:00
Adrian Schmutzler
1de9cac2f9 ramips: move redundant console setup to mt7621 SoC DTSI
For mt7621, console is set up via DTS bootargs individually in
device DTS/DTSI files. However, 44 of 74 statements use the
following setting:

	chosen {
		bootargs = "console=ttyS0,57600";
	};

Therefore, don't repeat ourselves and move that definition to the SoC
DTSI file to serve as a default value.

This patch is cosmetic.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-17 12:14:32 +02:00
John Audia
b6443367d8 kernel: bump 5.4 to 5.4.52
update_kernel.sh refreshed all patches, no human interaction was needed

Build system: x86_64
Run-tested: Netgear R7800 (ipq806x)

Signed-off-by: John Audia <graysky@archlinux.us>
2020-07-17 11:00:33 +02:00
Salvatore Mesoraca
2a43ab4a18 ramips: add arl_table support for MT7530
Use switch.h API to expose MT7530's ARL table to
user space.

Signed-off-by: Salvatore Mesoraca <salvatore@samknows.com>
2020-07-17 11:00:33 +02:00
Alberto Bursi
480003e9eb mvebu: add Kobol Helios 4 device
The Helios 4 is a NAS from Kobol
that is powered by an Armada 38x
MicroSOM from Solidrun, similarly
to Clearfog.

This device has:
-Armada 38x CPU
 (dual core ARMv7 1.6 Ghz)
-2 GB of ECC RAM
-Gigabit ethernet (Marvell)
-2x USB 3.0 ports
-4x Sata 3.0 ports
-i2c header (J9 |>GND|SDA|SCL|VCC)
-2x 3-pin fan headers with PWM
-micro-usb port is a TTL/UART to
 USB converter connected to TTL
-MicroSD card slot
-System, 4xSata and 1xUSB LEDs

NOT WORKING: fan control

Fan Control requires a kernel patch
that is available in the Armbian
project (the "default firmware"
of this device) and named
mvebu-gpio-remove-hardcoded
-timer-assignment
This patch isn't acceptable
by OpenWrt, it should be upstreamed.
I also have that patch in my own
local OpenWrt builds,
in case you want a more
clean and less confusing patch
for upstreaming.

To install, write the disk image
on a micro SD card with dd or
win32 disk imager, insert the
card in the slot.
Check that the dip switch battery
for boot selection is as follows
Switch 1 and 2 down/off, switches
3, 4, 5 up/on.

Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
2020-07-17 11:00:33 +02:00
Mateus B. Cassiano
73e8f23579 ramips: add support for D-Link DIR-867/DIR-882 A1
This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given
the similarity of these devices, this patch also introduces a common DTS
shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1.

Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
        WiFi 5G (green), USB 2.0 (green), USB 3.0 (green)

Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
* DIR-867 wireless chips are limited to 3x3 streams at hardware level
* USB ports and related LEDs available only on DIR-882

Serial port:
* Parameters: 57600, 8N1
* Location: J1 header (close to the Reset, WiFi and WPS buttons)
* Pinout: 1 - VCC
          2 - RXD
          3 - TXD
          4 - GND

Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
  button, then re-plug it. Keep the reset button pressed until the power
  LED starts flashing orange, manually assign a static IP address under
  the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1

* Some modern browsers may have problems flashing via the Recovery GUI,
  if that occurs consider uploading the firmware through cURL:

    curl -v -i -F "firmware=@file.bin" 192.168.0.1

Signed-off-by: Mateus B. Cassiano <mbc07@live.com>
[move DEVICE_VARIANT to individual definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-16 18:40:20 +02:00
Santiago Rodriguez-Papa
ed087cba8a ramips: add support for Linksys EA7300 v1
Specifications:

* SoC:      MediaTek MT7621A              (880 MHz 2c/4t)
* RAM:      Nanya NT5CC128M16IP-DIT       (256M DDR3-1600)
* Flash:    Macronix MX30LF1G18AC-TI      (128M NAND)
* Eth:      MediaTek MT7621A              (10/100/1000 Mbps x5)
* Radio:    MT7615N                       (2.4 GHz & 5 GHz)
            4 antennae: 1 internal and 3 non-deatachable
* USB:      3.0 (x1)
* LEDs:
    White   (x1 logo)
    Green   (x6 eth + wps)
    Orange  (x5, hardware-bound)
* Buttons:
    Reset   (x1)
    WPS     (x1)

Everything works! Been running it for a couple weeks now and haven't had
any problems. Please let me know if you run into any.

Installation:

Flash factory image through GUI.

This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.

Reverting to factory firmware:

Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.

Signed-off-by: Santiago Rodriguez-Papa <contact@rodsan.dev>
[use v1 only, minor DTS adjustments, use LINKSYS_HWNAME and add it to
DEVICE_VARS, wrap DEVICE_PACKAGES, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-16 13:39:44 +02:00
Adrian Schmutzler
95a05b12d7 ramips: provide common definition for ELECOM WRC GS devices
Add a common definition for ELECOM WRC "GS" devices to mt7621.mk
to not repeat the same assignments five times.

To keep the naming consistent, slightly rename the DTSI and the
factory image recipe as well.

Note that elecom_wrc-1167ghbk2-s uses a slightly different build
recipe for the factory image, so we keep it separate.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> [WRC-1750GSV]
2020-07-16 13:39:44 +02:00
INAGAKI Hiroshi
a79f55e7e0 ramips: add support for ELECOM WRC-1750GS/GSV
ELECOM WRC-1750GS is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.

WRC-1750GSV has the same hardware with WRC-1750GS.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: SPI-NOR 16 MiB
- WLAN		: 2.4/5 GHz 3T3R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LED/keys	: 4x/6x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, GND, TX, RX from ethernet port side
  - 57600n8
- Power		: 12VDC, 1.5A

Flash instruction using factory image:

1. Boot WRC-1750GS (or WRC-1750GSV) normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
   for WRC-1750GS : wrc-1750gs-squashfs-factory.bin
   for WRC-1750GSV: wrc-1750gsv-squashfs-factory.bin
4. Wait ~120 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-07-16 13:39:44 +02:00
John Crispin
eff87b8f93 mediatek: backport latest pci/e driver from upstream
Signed-off-by: John Crispin <john@phrozen.org>
2020-07-16 09:18:28 +02:00
John Crispin
5a5031e70b mediatek: generate UBI images for the rev board
Signed-off-by: John Crispin <john@phrozen.org>
2020-07-16 09:16:34 +02:00
John Crispin
ea2884e018 mediatek: minor fix to eip97 driver
This patch makes the driver work on the newer v2.3 core.

Signed-off-by: John Crispin <john@phrozen.org>
2020-07-16 09:14:49 +02:00
Adrian Schmutzler
9f3415d30b ath79: harmonize model names for Ubiquiti devices
This harmonizes the model names for the ath79 Ubiquiti devices by
applying a few minor cosmetic adjustments:

- Removes hyphens where they are not found in the product names
  (Ubiquiti uses hyphens only for the abbreviated version names
  like UAP-AC-PRO which we don't use anyway.)

- Add (XM) suffix for DTS model strings to help with distinguishing
  them from their XW counterparts.

- Remove DEVICE_VARIANT for LAP-120 which actually was an alternate
  device name.

- Generally make DTS model names and those from generic-ubnt.mk
  more consistent.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 18:41:57 +02:00
Vieno Hakkerinen
8c7e9cc6b5 ath79: add support for Ubiquiti PowerBridge M
This adds support for the Ubiquiti PowerBridge M, which has the same
board/LEDs as the Bullet M XM, but different case and antennas.

Specifications:
- AR7241 SoC @ 400 MHz
- 64 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- Internal antenna: 25 dBi
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB

Flashing via WebUI:
Upload the factory image via the stock firmware web UI.

Attention: airOS firmware versions >= 5.6 have a new bootloader with
an incompatible partition table!

Please downgrade to <= 5.5 _before_ flashing OpenWrt!
Refer to the device's Wiki page for further information.

Flashing via TFTP:
Same procedure as other Bullet M (XM) boards.

- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
  tftp> bin
  tftp> trace
  tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbridge-m-squashfs-factory.bin

Signed-off-by: Vieno Hakkerinen <vieno@hakkerinen.eu>
2020-07-15 18:33:56 +02:00
John Crispin
9da2b56760 ipq40xx: fix ethernet vlan double tagging
As the the SoC uses implicit vlan tagging for dual MAC support, the
offload feature breaks when using double tagging.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: John Crispin <john@phrozen.org>
2020-07-14 18:31:48 +02:00
John Crispin
2557d2eb4c ipq40xx: merge all ar40xx patches into one single patch
Signed-off-by: John Crispin <john@phrozen.org>
2020-07-14 18:31:12 +02:00
Adrian Schmutzler
3635f7efc1 ipq806x: really fix aliases node for Qualcomm IPQ8064/DB149
Having looked at this again, it appears that only gsbi2_serial
is actually enabled for this device, so the entry in the broken
aliases node was correct.

Therefore, this needs to set its own serial0 instead of inheriting
"serial0 = &gsbi4_serial;" from DTSI. Do this with the correctly
named aliases node now.

Fixes: c83f7b6d21 ("ipq806x: fix aliases node name for Qualcomm
IPQ8064/DB149")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 17:02:40 +02:00
Adrian Schmutzler
e363470d1a ipq806x: use consistent DT labels for gsbiX_serial
Kernel uses the label gsbiX_serial, so let's adjust our labels to
this naming scheme.

This is cosmetic, and actually only already existing gsbi4_serial
has been used at all.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 12:38:24 +02:00
Adrian Schmutzler
c83f7b6d21 ipq806x: fix aliases node name for Qualcomm IPQ8064/DB149
This device uses a node incorrectly named "alias" instead of
"aliases" since it was introduced.

Remove it without replacement, as the definitions in it don't
seem to be required anyway:

The serial0 definition has never been effective anyway and this
would be the only device deviating from the common setting
"serial0 = &gsbi4_serial;" for ipq8064. (So, maybe the wrong
node prevented us from finding out about the wrong serial
definition?)

The mdio-gpio0 alias was supposed to be removed in d2a2eb7e48
anyway, the redundant definition in the alias node was just
overlooked back then.

Fixes: 0fd202f3e5 ("ipq806x: add db149 dts files")
Fixes: d2a2eb7e48 ("ipq806x: replace caf nss-gmac driver by upstream stmmac")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 12:38:24 +02:00
Roger Pueyo Centelles
26fda610f3 ath79: use rgmii-id instead of rgmii in ubnt,lap-120
Since commit 6f2e1b7485 (ath79: disable delays on AT803X config init)
the incoming incoming traffic on the ubnt,lap-120 devices Ethernet
port was not making it through. Using rgmii-id instead of rgmii (same
configuration as ubnt,litebeam-ac-gen2) fixes it.

Fixes FS#2893.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-07-13 23:35:51 +02:00
Mathieu Martin-Borret
d7233b0a6a ramips: add support for D-Link DIR-878 A1
Specifications:

    SoC: MT7621AT
    RAM: 128MB
    Flash: 16MB NOR SPI flash
    WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
    LAN: 5x1000M
    Firmware layout is Uboot with extra 96 bytes in header
    Base PCB is AP-MTKH7-0002
    LEDs Power Green,Power Orange,Internet Green,Internet Orange
    LEDs "2.4G" Green & "5G" Green connected directly to wifi module
    Buttons Reset,WPS,WIFI

Flashing instructions:

Upload image via emergency recovery mode
Push and hold reset button (on the back of the device) until power led
starts flashing (about 10 secs or so) while powering the device on.
Give it ~30 seconds, to boot the recovery mode GUI
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
Call the recovery page for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device. Some browsers/OS combinations are known not to work, so if
you don't see the percentage complete displayed and moving within a few
seconds, restart the procedure from scratch and try anoher one,
or try the command line way.

Alternative method using command line on Linux:
curl -v -i -F "firmware=@openwrt-xxxx-squashfs-factory.bin" 192.168.0.1

Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com>
[use of generic uimage-padhdr in image generation code]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-13 22:45:04 +02:00
Mathieu Martin-Borret
96761ecc2f kernel: mtdsplit_uimage: add SGE parser
Adding SGE parser for SGE (T&W) Shenzhen Gongjin Electronics
to add 96 bytes padding the the firmware image

Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com>
2020-07-13 22:45:04 +02:00
David Bauer
0485fb3925 rockchip: don't disable timer LED trigger
The timer LED trigger is enabled in all targets (except for lantiq
xway-legacy). It's necessary for the OpenWrt preinit LED pattern to
work.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-13 17:50:53 +02:00
David Bauer
875a04478c rockchip: use downstream GPIO button implementation
Use the OpenWrt netlink GPIO button implementation to forward button
presses to procd. This is necessary to make failsafe-mode access
using a button possible.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-13 17:50:35 +02:00
Adrian Schmutzler
eb15b0e0c9 bcm47xx: disable image for Linksys WRT160n v3
The device can only hold 3.6 MB, but newer images (since 18.06)
are bigger, so flashing a new version fails.

This disables default build for this device based on the bug report
referenced below.

Fixes: FS#1963

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-13 10:37:22 +02:00
Adrian Schmutzler
11478524a2 ramips: consolidate Netgear devices for mt7628
This creates a common DTSI and shared image definition for the
relatively similar Netgear devices for mt7628 platform.

As a side effect, this raises SPI flash frequency for the R6120,
as it's expected to work there as well if it works for R6080 and
R6020.

Based on the data from the other devices, it also seems probable
the 5g MAC address for R6120 could be extracted from the caldata,
and the mtd-mac-address there could be dropped.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-13 10:37:22 +02:00
Chuanhong Guo
28893f5878 ath79: fix dsa binding for TP-Link TL-WR941ND v2
upstream changed dt-bindings for marvell 88e6060 to use mdio-device
and dropped support for legacy bindings.
fix it in our local dts.

Fixes: FS#2524
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-07-12 16:17:28 +08:00
Chuanhong Guo
0997342f24 ath79: qihoo,c301: use phy-supply for usb vbus
Linux phy subsystem provides support for a phy regulator defined via
phy-supply property. Use it to turn on usb power only when usb is
probed.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-07-12 15:39:18 +08:00
Tomasz Maciej Nowak
2dc5ce622a mvebu: add support for MACCHIATObin Single Shot
Add support for Marvell MACCHIATObin Single Shot, cortex-a72 based
Marvell ARMADA 8040 Community board. Single Shot was broken as the
device tree is different on the Double Shot Board.

Specifications:
- Quad core Cortex-A72 (up to 2GHz)
- DDR4 DIMM slot with optional ECC and single/dual chip select support
- Dual 10GbE (1/2.5/10GbE) SFP+
  2.5GbE (1/2.5GbE) via SFP
  1GbE via copper
- SPI Flash
- 3 X SATA 3.0 connectors
- MicroSD connector
- eMMC
- PCI x4 3.0 slot
- USB 2.0 Headers (Internal)
- USB 3.0 connector
- Console port (UART) over microUSB connector
- 20-pin Connector for CPU JTAG debugger
- 2 X UART Headers
- 12V input via DC Jack
- ATX type power connector
- Form Factor: Mini-ITX (170 mm x 170 mm)

More details at http://macchiatobin.net

Installation:

Write the Image to your Micro SD Card and insert it in the
MACCHIATObin Single Shot SD Card Slot.

In the U-Boot Environment:
   1. reset U-Boot environment:
      env default -a
      saveenv

   2. prepare U-Boot with boot script:
      setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000"
      saveenv

   or manually (hanging lines indicate wrapped one-line command):
      setenv fdt_name armada-8040-mcbin-singleshot.dtb
      setenv image_name Image
      setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr
         $image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv
         bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
         $kernel_addr - $fdt_addr'
      saveenv

   On newer Bootloaders (18.12) the Variables have been changed, use:
      setenv fdt_name armada-8040-mcbin-singleshot.dtb
      setenv image_name Image
      setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr_r
         $image_name;ext4load mmc 1:1 $fdt_addr_r $fdt_name;setenv
         bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
         $kernel_addr_r - $fdt_addr_r'

Reported-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: Alexandra Alth <alexandra@alth.de>
[add specs and installation as provided by Alexandra Alth]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-12 02:06:02 +02:00
Adrian Schmutzler
479adb0929 ramips: consolidate recipes with uimage_padhdr
There are already two very similar recipes using uimage_padhdr
in ramips target, and a third one is about to be added.

Make the recipe more generic, so redefinitions are not necessary
anymore.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Bjørn Mork <bjorn@mork.no> [Zyxel WAP6805]
2020-07-11 18:38:42 +02:00