In order to support SAE/WPA3-Personal in default images. Replace almost
all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for
consistency. Keep out ar71xx from the list as it won't be in the next
release and would only make backports harder.
Build-tested (build-bot settings):
ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway,
sunxi: a53
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This PR is a blend of several kernel bumps authored by ldir taken from his
staging tree w/ some further adjustments made by me and update_kernel.sh
Summary:
Deleted upstreamed patches:
generic:
742-v5.5-net-sfp-add-support-for-module-quirks.patch
743-v5.5-net-sfp-add-some-quirks-for-GPON-modules.patch
bcm63xx:
022-v5.8-mtd-rawnand-brcmnand-correctly-verify-erased-pages.patch
024-v5.8-mtd-rawnand-brcmnand-fix-CS0-layout.patch
mediatek:
0402-net-ethernet-mtk_eth_soc-Always-call-mtk_gmac0_rgmii.patch
Deleted patches applied differently upstream:
generic:
641-sch_cake-fix-IP-protocol-handling-in-the-presence-of.patch
Manually merged patches:
generic:
395-v5.8-net-sch_cake-Take-advantage-of-skb-hash-where-appropriate.patch
bcm27xx:
950-0132-lan78xx-Debounce-link-events-to-minimize-poll-storm.patch
layerscape:
701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch
Build system: x86_64
Build-tested: ath79/generic, bcm27xx/bcm2708, bcm27xx/bcm2711,
imx6, mvebu/cortexa9, sunxi/a53
Run-tested: Netgear R7800 (ipq806x)
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-By: Lucian Cristian <Lucian.cristian@gmail.com> [mvebu]
Tested-By: Curtis Deptuck <curtdept@me.com> [x86/64]
[do not remove 395-v5.8-net-sch_cake-Take-advantage-... patch,
adjust and refresh patches, adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-By: John Audia <graysky@archlinux.us> [ipq806x]
It is deactivated everywhere, just set this in the generic config.
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ifconfig is effectively deprecated for quite some time now. Let's
replace the remaining occurrences for our target setup by the
corresponding ip commands now.
Note that this does not touch ar71xx, as it will be dropped anyway,
and changing it would only make backports harder.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds a full eMMC image including U-Boot, which means that the
kernel can inherit the true RAM size detected by the preloader.
As implemented in previous commits, sysupgrade to this image from
the legacy layout (and via that, from the vendor-installed image)
is supported.
Rename the legacy image for the 512MiB board, for clarity.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
As I buy more hardware and continue to work on consolidation, This will
apply to a lot of MediaTek platforms; rename it accordingly.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This actually covers fairly much all the MediaTek platforms; they
only have different images because they don't include the preloader
and U-Boot, and rely on preinstalled stuff from the vendor.
So this script can slowly take over the world as we complete the
support for various other platforms, starting with UniElec U7623…
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Many MediaTek SoCs can be unbricked by using the SP Flash Tool from
http://spflashtool.com/ along with a "scatter list" file, which is
just a text file listing which image gets loaded where.
We use a trivial partition layout for the tool, with the whole eMMC
image as a single "partition", which means users just need to unzip
the sysupgrade image. Doing the real partition layout would be overly
complex and would require the individual partitions to be shipped
as artifacts — or users to extract them out of the sysupgrade image
just for the tool to put them adjacent to each other on the eMMC
anyway.
The tool does require a copy of the preloader in order to operate,
even when it isn't flashing the preloader to the eMMC boot region.
So drop that into the bin directory as an artifact too.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
bpi-r2 images are shipped with mainline u-boot which can extract lzma
with no problem.
remove custom kernel recipe to build lzma fit image instead of
uncompressed fit with zboot.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
An upcoming commit will add a full system image for U7623 which will
contain the MBR partition table and U-Boot too.
That contrasts with the current image which only owns the eMMC from
sector 0xa00 onwards, and must start with a legacy uImage.
Prepare for sysupgrade to the new images, and cope with the fact that
the recovery partition will be /dev/mmcblk0p2 instead of /dev/mmcblk0p1
after the upgrade.
This commit could potentially be backported to 19.07 to allow for direct
sysupgrade to the new image layout.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I'm about to change the layout of the images for UniElec U7623 so make it
find the recovery partition based on which the root partition is too.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The definition of the switch in the device-tree was not correct. Make it
look more like the Banana Pi R2, which works.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This board ships with an ancient 14.07-based OpenWrt using block2mtd, and
the MBR partition table contains nonsense.
It is possible to sysupgrade to an upstream OpenWrt image, but the
legacy layout of the OpenWrt images start at 0xA00 in the eMMC, with
a raw uImage. The legacy OpenWrt image doesn't "own" the beginning
of the device, including the MBR and U-Boot.
This means that when a user upgrades to upstream OpenWrt, it doesn't
boot because it can't find the right partitions. So hard-code them on
the kernel's command line using CONFIG_CMDLINE_PARTITION (for block).
Additionally, the vendor firmware doesn't cope with images larger than
about 36MiB, because it only overwrites the contents of its "firmware"
MTD partition. The current layout of the legacy image wastes a lot of
space, allowing over 32MiB for the kernel and another 10MiB for the FAT
recovery file system which is only created as 3MiB. So pull those in
to allow 4¾ MiB for the kernel, 3MiB for recovery, and then we have over
20MiB for the root file system.
This doesn't affect the new images which ship with a full eMMC image
including a different MBR layout and a partition for U-Boot, because
our modern U-Boot can actually pass the command line to the kernel, and
the built-in one doesn't get used anyway.
Tested by upgrading from vendor OpenWrt to the current legacy image,
from legacy to itself, to the previous legacy layout, and then to
finally the full-system image.
This commit probably wants backporting to 19.07, which also doesn't
install over the vendor OpenWrt and doesn't even have a full-system
installation option.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The current condition with part of the variables set dependent on
the subtarget in Device/Default isn't really nice to read and also
defeats the purpose of having a default node.
This removes the special settings for mt7623 and moves them to the
individual devices, which is not much of a problem as there are
actually just two of them and they partly use different settings
anyway.
While at it, slightly adjust the order of variables and wrap some
long lines.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
update_kernel.sh refreshed all patches, no human interaction was needed
Build system: x86_64
Run-tested: Netgear R7800 (ipq806x)
Signed-off-by: John Audia <graysky@archlinux.us>
There was a bashism in the script. This fixes the script so that it
doesn't actually require bash, and can be run with any POSIX shell as
its shebang suggests.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch is required for pcie@2,0 in mt7623 to work. The patch was originally
added in kernel 4.14, but it has not been ported to 4.19 and later.
Fixes: FS#3217
Tested-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Since commit 298814e6be ("base-files: config_generate: split macaddr with
multiple ifaces") uci MAC address setup will create a device node for each
member iface. But this script might override the device nodes and interfere
with the MAC address setup.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Commit e53ec043ba ("kirkwood: move usb support to modules") has moved
this config symbol into generic configs, so it could be removed from
other configs.
Suggested-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Like many boards, the Banana Pi R2 doesn't have permanant storage of
its MAC address, and we store the first random one that the kernel
generates in order to use it later and at least be consistent.
Store it in the FAT boot partition, just as the U7623 board (and others)
do.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The MT7623 SoC has the same SATA block as the MT7622, so enable it in
MT7623 builds too and add it to the DEVICE_PACKAGES for those boards.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The supported MT7623 boards are mostly identical (what with being a
System-on-Chip and all), so unify the DEVICE_PACKAGES for them, and add
ext4 and usb support for them.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Some options were not explicitly specified, causing the kernel build to
drop to interactive mode. Set the missing options.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fixes:
- CVE-2020-10757
The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.
Run tested: ath79
Build tested: ath79
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The uci config section network.globals set up in /bin/config_generate
will only be created if /proc/sys/net/ipv6 exists.
Correspondingly, lacking IPv6 support, the command
uci set network.globals.packet_steering=1
will fail with "uci: Invalid argument" as the network.globals config
has not been set up.
Fix that by adding the setup there as well.
While at it, limit the uci commit to the network config file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- sort device recipes alphabetically
- adjust board name of ELECOM WRC-2533GENT
- harmonize line wrapping
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebased]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
