5211264 odhcpd: add support for dhcpv6_pd_min_len parameter
c6bff6f router: Add PREF64 (RFC 8781) support
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix a typo where the wrong KCONFIG was used and fix selecting the
correct kernel config option to use these packages.
Fixes: 4f443c885d ("netfilter: separate packages for kmod-ipt-socket and kmod-ipt-tproxy")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
1571e18e4a69 bridge: add support for configuring extra tagged vlans on member devices
b719f189f243 bridge: make hotplug-added vlans default to tagged
edf3aced9f9a bridge: add support for adding vlan ranges via hotplug
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ath10k does not report excessive loss in case of broken block-ack
sessions. The loss is communicated to the host-os, but ath10k does not
trigger a low-ack events by itself.
The mac80211 framework for loss detection however detects this
circumstance well in case of ath10k. So use it regardless of ath10k's
own loss detection mechanism.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
========
CPU Qualcomm Atheros QCA9558
RAM 256MB DDR2
FLASH 2x 16M SPI-NOR (Macronix MX25L12805D)
WIFI Qualcomm Atheros QCA9558
Atheros AR9590
Installation
============
1. Attach to the serial console of the AP-105.
Interrupt autoboot and change the U-Boot env.
$ setenv rb_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66;
netget 0x80060000 ap115.bin; go 0x80060000"
$ setenv fb_openwrt "bank 1;
cp.b 0xbf100040 0x80060000 0x10000; go 0x80060000"
$ setenv bootcmd "run fb_openwrt"
$ saveenv
2. Load the OpenWrt initramfs image on the device using TFTP.
Place the initramfs image as "ap105.bin" in the TFTP server
root directory, connect it to the AP and make the server reachable
at 192.168.1.66/24.
$ run rb_openwrt
3. Once OpenWrt booted, transfer the sysupgrade image to the device
using scp and use sysupgrade to install the firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
077e05f2b129 vlan/vlandev: pass through extra vlan information passed via hotplug
40fad91eb5be wireless: add network_vlan config attribute
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hardware
--------
SOC: MediaTek MT7986
RAM: 1024MB DDR3
FLASH: 128MB SPI-NAND (Winbond)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: Realtek RTL8221B-VB-CG 2.5 N-Base-T PHY with PoE
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect the TFTP server to the WAX220. Conect to the serial console,
interrupt the autoboot process by pressing '0' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.2.1
$ setenv serverip 192.168.2.2
$ tftpboot openwrt.bin
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Now that qualcommax exists as a target and dependencies have been updated
let move ipq807x support to subtarget of qualcommax.
This is mostly copy/paste with the exception of having to update SSDK and
NSS-DP to use CONFIG_TARGET_SUBTARGET.
This is a preparation for later addition of IPQ60xx and IPQ50xx support.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, ipq807x only covers Qualcomm IPQ807x SoC-s.
However, Qualcomm also has IPQ60xx and IPQ50xx SoC-s under the AX WiSoC-s
and they share a lot of stuff with IPQ807x, especially IPQ60xx so to avoid
duplicating kernel patches and everything lets make a common target with
per SoC subtargets.
Start doing that by renaming ipq807x to qualcommax so that dependencies
on ipq807x target can be updated.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add an UCI option to enable Multiple BSSID Advertisement. Enabling this
will announce all BSSIDS on a phy in a single beacon frame. The
interface that is brought up first will be the transmitting profile, all
others are non-transmitting profiles and will be advertised in the
Multiple BSSID element in Beacon and Probe Response frames of the first
interface.
This depends on driver and client support. Enabling this will result in
all but the first interface not being visible at all for clients that do
not support it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Some Broadcom MIPS devices require JFFS2 cleanmarkers to be present on the
kernel partition or the bootloader will identify the partition as corrupt and
won't boot the kernel.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
openssl sets additional cflags in its configuration script. We need to
make it aware of our custom cflags to avoid adding conflicting cflags.
Fixes: #12866
Signed-off-by: Jitao Lu <dianlujitao@gmail.com>
Backport patches improving ppp interface creation. As a side effect this
also fix a bug from using netdev trigger that suffer from LED state
wrongly set due to using old ioctl for ppp creation.
Tested-by: Csaba Sipos <metro4@freemail.hu>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
source.codeaurora.org project has been shut down and the nxp
repositories has been moved to github. Update the repository
link to the new location.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
source.codeaurora.org project has been shut down and the nxp
repositories has been moved to github. Update the repository
link to the new location.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
If dual-stack configuration is in use, and dhcpv6 option is set, do not start
464xlat sub-interface for dhcpv6 sub-interace , as the configuration already
provides IPv4 connectivty, be it through single or dual APN configuration.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add two new "v6apn" and "v6profile" properties, to support split-APN
dual-stack onfiguration. This extends the existing ipv4v6 PDP type,
allowing simultaneous connection to two distinct APNs,
one for IPv4 and one for IPv6.
The parameters override existing 'apn' and 'profile' respectively,
if set, but only for IPv6 part of the connection.
If unset, they default to their original values, constituting a standard
IPv4v6 setup.
If a different APN is set for IPv6, a corresponding profile MUST also be
configured, with a different ID, than the IPv4 profile, for example,
profile 2.
Both APNs must match ones configured through QMI or through 'AT+CGDCONT'
command.
Example configuration in UCI:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option autoconnect '1'
option pdptype 'ipv4v6'
option apn 'internet'
option v6apn 'internetipv6'
option profile '1'
option v6profile '2'
Corresponding profile configuration:
AT+CGDCONT?
+CGDCONT: 1,"IP","internet","0.0.0.0",0,0,0,0
+CGDCONT: 2,"IPV6","internetipv6","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
The cli is a one-time run, and memory leaks would have been irrelevant. But people call libsw with cli programs as samples.
Doing a good job of memory management calls means that people who call libsw are not so easy to make mistakes.
Signed-off-by: nichel Chen <nichelnich@gmail.com>
This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router.
Device specification
--------------------
SoC Type: MediaTek MT7621AT (880 MHz, 2 cores)
RAM (Nanya NT5CC64M16GP): 128 MiB
Flash (Macronix MX30LF1G18AC): 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615N): a/n/ac, 4x4
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
USB ports: 1xUSB3.0
Buttons: 2 button (reset, wps)
LEDs: Red, Green, Blue
Zigbee (EFR32MG1B232GG): 3.0
Stock bootloader: U-Boot 1.1.3
Power: 12 VDC, 1.5 A
Installation (fw 2.0.9)
-----------------------
1. Login to the web interface under SuperUser (root) credentials.
Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the
device written on the backplate stick.
2. Navigate to Setting -> WAN. Add:
Name - WAN1
Connection Type - Static
IP Address - 172.16.0.1
Netmask - 255.255.255.0
Save -> Apply. Set default: WAN1
3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add:
Protocol - SSH
Port - 22
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN Interface - WAN1
Save ->Apply
Add:
Protocol - HTTP
Port - 80
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN interface - WAN1
Save -> Apply
4. Set up your PC ethernet:
Connection Type - Static
IP Address - 172.16.0.2
Netmask - 255.255.255.0
Gateway - 172.16.0.1
5. Connect PC using ethernet cable to the WAN port of the router
6. Connect to the router using SSH shell under SuperUser account
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface under admin account
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 171.16.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses (fw 2.0.9)
------------------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:e8 |
| WAN | label + 1 | *:e9 |
| 2g | label + 4 | *:ec |
| 5g | label + 5 | *:ed |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
Factory image format
--------------------
+---+-------------------+-------------+--------------------+
| # | Offset | Size | Description |
+---+-------------------+-------------+--------------------+
| 1 | 0x0 | 0x200 | Tag Header Factory |
| 2 | 0x200 | 0x100 | Tag Header Kernel1 |
| 3 | 0x300 | 0x100 | Tag Header Kernel2 |
| 4 | 0x400 | SIZE_KERNEL | Kernel |
| 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) |
+---+-------------------+-------------+--------------------+
Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
The armvirt target has been renamed to armsr (Arm SystemReady),
so the GRUB configuration also needs to change.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Contains following updates:
* ipq8074: update RegDB in new submitted BDF
* Revert "ipq8074: update RegDB in new submitted BDF"
* qcn9074: update RegDB in new submitted BDF
* ipq8074: update RegDB in new submitted BDF
* qca-wireless: ipq40xx: add BDFs for ZTE MF287+
* Add BDFs for prpl Foundation Haze board
Signed-off-by: Petr Štetiar <ynezz@true.cz>
There is no need for SSDK to support 5.15 anymore since the only user and
possible future ones are on 6.1.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit add u-boot env config for GL-MT3000, so
that we can use fw_printenv to print u-boot env and
use fw_setenv to set u-boot env in GL-MT3000.
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
CVE-2023-2650 fix
Remove upstreamed patches
Major changes between OpenSSL 3.0.8 and OpenSSL 3.0.9 [30 May 2023]
* Mitigate for very slow OBJ_obj2txt() performance with gigantic OBJECT IDENTIFIER sub-identities. (CVE-2023-2650)
* Fixed buffer overread in AES-XTS decryption on ARM 64 bit platforms (CVE-2023-1255)
* Fixed documentation of X509_VERIFY_PARAM_add0_policy() (CVE-2023-0466)
* Fixed handling of invalid certificate policies in leaf certificates (CVE-2023-0465)
* Limited the number of nodes created in a policy tree (CVE-2023-0464)
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
One is never to write to dev->addr directly. In 6.1 it will be a const and
with the newly enabled WERROR, we get a failing grade.
Lets fix this ahead of time.
Ref: adeef3e321
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Update bootloader environment for BPi-R3 and BPi-R64 to adapt to new
device tree overlay mechanism now that support for multiple device
tree overlays has been added.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 5d2de00555.
I received multiple reports that in various configurations this FW version
is not stable and crashes, so lets revert to 01385 revision which works.
Fixes#12815
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [fixes tag]
Currently kernel crashes when of_phy_connect has issues:
Unable to handle kernel access to user memory outside uaccess routines at virtual address 0000000000000308
...
pc : phy_attached_print+0x28/0x1b0
lr : phy_attached_info+0x14/0x20
...
Call trace:
phy_attached_print+0x28/0x1b0
phy_attached_info+0x14/0x20
nss_dp_adjust_link+0x544/0x6c4 [qca_nss_dp]
of_phy_connect returns either pointer or NULL, so can't be checked with
IS_ERR macro.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
b09b316aeaf6 blobmsg: add blobmsg_parse_attr function
eac92a4d5d82 blobmsg: add blobmsg_parse_array_attr
ef5e8e38bd38 usock: fix poll return code check
6fc29d1c4292 jshn.sh: Add pretty-printing to json_dump
5893cf78da40 blobmsg: Don't do at run-time what can be done at compile-time
362951a2d96e uloop: fix uloop_run_timeout
75a3b870cace uloop: add support for integrating with a different event loop
Signed-off-by: Felix Fietkau <nbd@nbd.name>
412d03012f13 network: prevent adding endpoint routes for addresses on the network
faaf9cee6ef4 utils: fix ipv4 checksum issue
0e1c2fad3540 pex-msg: fix memory leak on fread fail in pex_msg_update_request_init
51be0ed659d0 host: fix crash parsing gateway when no endpoint is specified
ca17601dc24e wg-linux: add support for splitting netlink messages for allowed ips
7d3986b7a5a2 wg-linux: increase default messages size
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Synchronize the ath11k backports with the current ath-next tree.
This introduces support for MBSSID and EMA, adds factory test mode and
some new HTT stats.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport EMA beacon support from kernel 6.4.
It is required for MBSSID/EMA suport in ath11k that will follow.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
QCA released a point update for the 2.9.0.1 firmware, so lets update to it.
Runtime tested on Dynalink DL-WRX36.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Built-in engine configs are added in libopenssl-conf/install stage
already, postinst/add_engine_config is just duplicating them, and
due to the lack of `config` header it results a broken uci config:
> uci: Parse error (invalid command) at line 3, byte 0
```
config engine 'devcrypto'
option enabled '1'
engine 'devcrypto'
option enabled '1'
option builtin '1'
```
Add `builtin` option in libopenssl-conf/install stage and remove
duplicate engine configuration in postinst/add_engine_config to
fix this issue.
Fixes: 0b70d55a64 ("openssl: make UCI config aware of built-in engines")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
