Commit Graph

51228 Commits

Author SHA1 Message Date
Michael Pratt
01bbed7444 ramips: mt7620: fix ethernet driver GMAC port init
A workaround was added to the switch driver
to set SOC port 4 as an RGMII GMAC interface
based on the DTS property mediatek,port4-gmac.
(previously mediatek,port4)

However, the ethernet driver already does this,
but is being blocked by a return statement
whenever the phy-handle and fixed-link properties
are both missing from nodes that define the port properties.

Revert the workaround, so that both the switch driver
and ethernet driver are not doing the same thing
and move the phy-handle related lines down
so nothing is ending the function prematurely.

While at it, clean up kernel messages
and delete useless return statements.

Fixes: f6d81e2fa1 ("mt7620: gsw: make IntPHY and ExtPHY share mdio addr 4 possible")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit afd60d650e)
2022-04-19 14:48:21 +02:00
Michael Pratt
6491212ea7 ramips: mt7620: remove useless GMAC nodes
These nodes are used for configuring a GMAC interface
and for defining external PHYs to be accessed with MDIO.

None of this is possible on MT7620N, only MT7620A,
so remove them from all MT7620N DTS.

When the mdio-bus node is missing, the driver returns -NODEV
which causes the internal switch to not initialize.
Replace that return so that everything works without the DTS node.

Also, an extra kernel message to indicate for all error conditions
that mdio-bus is disabled.

Fixes: d482356322 ("ramips: mt7620n: add mdio node and disable port4 by default")
Fixes: aa5014dd1a ("ramips: mt7620n: enable port 4 as EPHY by default")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit a2acdf9607)
2022-04-19 14:48:21 +02:00
Michael Pratt
a14c2d409c ramips: mt7620: simplify DTS properties for GMAC
There are only 2 options in the driver
for the function of mt7620 internal switch port 4:

  EPHY mode (RJ-45, internal PHY)
  GMAC mode (RGMII, external PHY)

Let the DTS property be boolean instead of string
where EPHY mode is the default.

Fix how the properties are written
for all DTS that use them,
and add missing nodes where applicable,
and remove useless nodes,
and minor DTS formatting.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit 953bfe2eb3)
2022-04-19 14:48:21 +02:00
Gaspare Bruno
c652a06eef ramips: mt7620: enable autonegotiation for all ports
This enables autonegotiation for all ephy ports on probe.
Some devices do not configure the ports, particularly port 4.

Signed-off-by: Gaspare Bruno <gaspare@anlix.io>
[replace magic values ; reword commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 0056ffb468)
2022-04-19 14:48:21 +02:00
David Bauer
08ec622c46 ramips: make PHY initialization more descriptive
The basic mode control register of the ESW PHYs is modified in this
codeblock. Use the respective macros to make this code more readable.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 6a15abbc75)
2022-04-19 14:48:21 +02:00
Ben Gainey
4123f177f9 ramips: add support for the Wavlink WL-WN579X3
About the device
----------------

SoC: MediaTek MT7620a @ 580MHz
RAM: 64M
FLASH: 8MB
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 2x (RTL8211F)
BTN: - WPS
- Reset
- Router/Repeater/AP (3-way slide-switch)
LED: - WPS (blue)
- 3-segment Wifi signal representation (blue)
- WiFi (blue)
- WAN (blue)
- LAN (blue)
- Power (blue)
UART: UART is present as Pads with through-holes on the PCB. They are
located next to the reset button and are labelled Vcc/TX/RX/GND as
appropriate. Use 3.3V, 57600-8N1.

Installation
------------

Using the webcmd interface
--------------------------

Warning: Do not update to the latest Wavlink firmware (version
20201201) as this removes the webcmd console and you will need to
use the serial port instead.

You will need to have built uboot/sqauashfs image for this device,
and you will need to provide an HTTP service where the image can
be downloaded from that is accessible by the device.
You cannot use the device manufacturers firmware upgrade interface
as it rejects the OpenWrt image.

1. Log into the device's admin portal. This is necessary to
   authenticate you as a user in order to be able to access the
   webcmd interface.
2. Navigate to http://<device-ip>/webcmd.shtml - you can access
   the console directly through this page, or you may wish to
   launch the installed `telnetd` and use telnet instead.
   * Using telnet is recommended since it provides a more
     convenient shell interface that the web form.
   * Launch telnetd from the form with the command `telnetd`.
   * Check the port that telnetd is running on using
     `netstat -antp|grep telnetd`, it is likely to be 2323.
   * Connect to the target using `telnet`. The username should
     be `admin2860`, and the password is your admin password.
3. On the target use `curl` to download the image.
   e.g.  `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\
          wavlink_wl-wn579x3-squashfs-sysupgrade.bin`.
   Check the hash using `md5sum`.
4. Use the mtd_write command to flash the image.
   * The flash partition should be mtd4, but check
     /sys/class/mtd/mtd4/name first. The partition should be
     called 'Kernel'.
   * To flash use the following command:
     `mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>`
     Where mtd<n> is the Kernel partition, and <image-file> is
     the OpenWrt image previously downloaded.
   * The command above will erase, flash and then reboot the
     device. Once it reboots it will be running OpenWrt.

Connect via ssh to the device at 192.168.1.1 on the LAN port.
The WAN port will be configured via DHCP.

Using the serial port
---------------------

The device uses uboot like many other MT7260a based boards. To
use this interface, you will need to connect to the serial
interface, and provide a TFTP server. At boot follow the
bootloader menu and select option 2 to erase/flash the image.
Provide the address and filename details for the tftp server.
The bootloader will do the rest.

Once the image is flashed, the board will boot into OpenWrt. The
console is available over the serial port.

Signed-off-by: Ben Gainey <ba.gainey@googlemail.com>
(cherry picked from commit a509b80065)
2022-04-19 14:48:21 +02:00
Shiji Yang
92af15077f ramips: split Youku YK1 to YK-L1 and YK-L1c
Device specifications:
* Model: Youku YK-L1/L1c
* CPU: MT7620A
* RAM: 128 MiB
* Flash: 32 MiB (YK-L1)/ 16 MiB (YK-L1c)
* LAN: 2* 10M/100M Ports
* WAN: 1* 10M/100M Port
* USB: 1* USB2.0
* SD: 1* MicroSD socket
* UART: 1* TTL, Baudrate 57600

Descriptions:
  Previous supported device YOUKU yk1 is actually Youku YK-L1. Though they look
  really different, the only hardware difference between the two models is flash
  size, YK-L1 has 32 MiB flash but YK-L1c has 16MiB. It seems that YK-L1c can
  compatible with YK-L1's firmware but it's better to split it to different models.

  It is easy to identify the models by looking at the label on the bottom of the
  device. The label has the model number "YK-L1" or "YK-L1c". Due to different flash
  sizes, YK-L1c that using previous YK-L1's firmware needs to apply "force update"
  to install compatible firmware, so please backup config file before system upgrade.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[use more specific name for DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 4a9f389ed2)
2022-04-19 14:48:21 +02:00
Shiji Yang
55f8eb84d2 ramips: improve pinctrl for Youku YK-L1
1. rename led pin "air" to a more common name "wlan" and use "phy0tpt" to trigger it.
2. led "wan" can be triggered by ethernet pinctrl by default so just drop it.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 882a6116d3)
2022-04-19 14:48:21 +02:00
Shiji Yang
92489b4f82 ramips: speed up spi frequency for Youku YK-L1
Youku YK-L1 has a huge storage space up to 32 MB. It is better to
use a higher spi clock to read or write serial nor flash chips.
Youku YK-L1 has Winbond w25q256fvfg on board that can support
104 MHz spi clock so 48 MHz is safe enough.
The real frequency can only be sysclk(580MHz ) /3 /(2^n) so 80 MHz
defined in dts file will set only 48 MHz in spi bus.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit bf7ddb18f1)
2022-04-19 14:48:21 +02:00
DENG Qingfang
bea1891182 ramips: remove obsolete mx25l25635f compatible hack
The kernel bump to 5.4 has removed the mx25l25635f hack, and the
mx25l25635f compatible is no longer required.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
(cherry picked from commit 06af45ec05)
2022-04-19 14:48:21 +02:00
Josef Schlehofer
6c44b157e5 mvebu: kernel: enable CONFIG_BLK_DEV_NVME
CONFIG_BLK_DEV_NVME [1]:
- This is a kernel driver for SSD connected to PCI or PCIe bus [1].
By default, it is enabled for targets "ipq807x", "rockchip/armv8"
and "x86/64".

With miniPCIe adapter, there is a possibility to connect NVMe disk
to Turris Omnia (cortex-a9), Turris MOX (cortex-a53).

It allows to boot system from NVMe disk, because of that it can not
be kmod package as you can not access the disk to be able to boot from
it.

CONFIG_NVME_CORE [2]:
- This is selected by CONFIG_BLK_DEV_NVME
It does not need to be explicitly enabled, but it is done for "ipq807",
"x64_64" and rockchip/armv8", which has also enabled the previous config
option as well.

Kernel increase: ~28k KiB on mamba kernel

Reference:
[1] https://cateee.net/lkddb/web-lkddb/BLK_DEV_NVME.html
[2] https://cateee.net/lkddb/web-lkddb/NVME_CORE.html

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 9d530ac4bf)
[rebased for config-5.4]
2022-04-19 14:40:24 +02:00
Hauke Mehrtens
f0f9b7ac5c OpenWrt v21.02.3: revert to branch defaults
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-04-17 21:00:07 +02:00
Hauke Mehrtens
42a15ca378 OpenWrt v21.02.3: adjust config defaults
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-04-17 21:00:03 +02:00
Joe Mullally
1d4dea6d4f ath79: Move TPLink WPA8630Pv2 to ath79-tiny target
These devices only have 6MiB available for firmware, which is not
enough for recent release images, so move these to the tiny target.

Note for users sysupgrading from the previous ath79-generic snapshot
images:

The tiny target kernel has a 4Kb flash erase block size instead
of the generic target's 64kb. This means the JFFS2 overlay partition
containing settings must be reformatted with the new block size or else
there will be data corruption.

To do this, backup your settings before upgrading, then during the
sysupgrade, de-select "Keep Settings". On the CLI, use "sysupgrade -n".

If you forget to do this and your system becomes unstable after
upgrading, you can do this to format the partition and recover:

* Reboot
* Press RESET when Power LED blinks during boot to enter Failsafe mode
* SSH to 192.168.1.1
* Run "firstboot" and reboot

Signed-off-by: Joe Mullally <jwmullally@gmail.com>
Tested-by: Robert Högberg <robert.hogberg@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit message facelift]
(cherry picked from commit 44e1e5d)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-04-16 14:59:34 +02:00
Torsten Duwe
41a97c2074 bcm27xx: add AMP2 to HifiBerry DAC+ / DAC+ Pro package
According to the vendor [1] these HATs share the same DT overlay:
hifiberry-dacplus. The PCM512x-compatible control unit is attached to
I2C, so the additional snd-soc-pcm512x-i2c kernel module is required.
Also explicitly note the Amp2 support to reduce confusion for those
users.

[1] <https://www.hifiberry.com/docs/software/configuring-linux-3-18-x/>
Signed-off-by: Torsten Duwe <duwe@lst.de>
(added bcm27xx tag, changed commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 7ea9936f7f)
2022-04-16 14:55:27 +02:00
Thibaut VARÈNE
9a765554f4 ath79: add support for MikroTik RouterBOARD mAP lite
The MikroTik RouterBOARD mAPL-2nd (sold as mAP Lite) is a small
2.4 GHz 802.11b/g/n PoE-capable AP.

See https://mikrotik.com/product/RBmAPL-2nD for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9533
 - RAM: 64 MB
 - Storage: 16 MB NOR
 - Wireless: Atheros AR9531 (SoC) 802.11b/g/n 2x2:2, 1.5 dBi antenna
 - Ethernet: Atheros AR8229 (SoC), 1x 10/100 port, 802.3af/at PoE in
 - 4 user-controllable LEDs:
   · 1x power (green)
   · 1x user (green)
   · 1x lan (green)
   · 1x wlan (green)

Flashing:
 TFTP boot initramfs image and then perform sysupgrade. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Note: following 781d4bfb39
 The network setup avoids using the integrated switch and connects the
 single Ethernet port directly. This way, link speed (10/100 Mbps) is
 properly reported by eth0.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit eb38af7881)
2022-04-16 14:51:57 +02:00
Thibaut VARÈNE
2cc9ee8000 ath79: add support for Yuncore A930
Specification:

- QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR
- 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN)
- 2T2R 802.11b/g/n 2.4GHz

Flash instructions:

If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):

  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
  sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin

In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:

1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
   'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
   seconds, recovery mode should start downloading image from server
   (unfortunately, there is no visible indication that recovery got
   enabled - in case of problems check TFTP server logs)

Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry-picked from commit a05dcb0724)
[switch to mtd-mac-address instead of nvmem-cells]
2022-04-16 14:48:45 +02:00
Thibaut VARÈNE
06874171d1 ath79: add support for Yuncore XD3200
Specification:

- QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR
- 2T2R 802.11b/g/n 2.4GHz
- 2T2R 802.11n/ac 5GHz
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)

LED for 5 GHz WLAN is currently not supported as it is connected directly
to the QCA9882 radio chip.

Flash instructions:

If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):

  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
  sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin

In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:

1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
   'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
   seconds, recovery mode should start downloading image from server
   (unfortunately, there is no visible indication that recovery got
   enabled - in case of problems check TFTP server logs)

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry-picked from commit c91df224f5)
2022-04-16 14:48:29 +02:00
Eneas U de Queiroz
c5ef62a218 wolfssl: bump to 5.2.0
Fixes two high-severity vulnerabilities:

- CVE-2022-25640: A TLS v1.3 server who requires mutual authentication
  can be bypassed.  If a malicious client does not send the
  certificate_verify message a client can connect without presenting a
  certificate even if the server requires one.

- CVE-2022-25638: A TLS v1.3 client attempting to authenticate a TLS
  v1.3 server can have its certificate heck bypassed. If the sig_algo in
  the certificate_verify message is different than the certificate
  message checking may be bypassed.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit e89f3e85eb)
2022-04-11 22:52:57 +02:00
Hauke Mehrtens
99b00edf35 mac80211: Update to version 5.10.110-1
This updates mac80211 to version 5.10.110-1 which is based on kernel
5.10.110.
The removed patches were applied upstream.

This new release contains many fixes which were merged into the upstream
Linux kernel.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-04-11 22:51:57 +02:00
Tony Ambardar
9132344444 bpftools: fix feature override for masking clang
Rename feature variable clang-bpf-global-var following upstream changes.
This restores the HAVE_CLANG feature override and should avoid rare build
errors where a recent host clang and BTF-enabled host kernel are present.

Fixes: 23be333401 ("bpftools: update to 5.10.10")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
(cherry picked from commit cf20f1bb5f)
2022-04-11 22:51:57 +02:00
Michael Pratt
169c9e3a88 ramips: fix reboot for remaining 32 MB boards
The following devices have a Winbond W25Q256FV flash chip,
which does not have the RESET pin enabled by default,
and otherwise would require setting a bit in a status register.

Before moving to Linux 5.4, we had the patch:
0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch
which kept specific flash chips with explicit 3-byte and 4-byte address modes
to stay in 3-byte address mode while idle (after an erase or write)
by using a custom flag SPI_NOR_4B_READ_OP that was part of the patch.

this was obsoleted by the patch:
481-mtd-spi-nor-rework-broken-flash-reset-support.patch
which uses the newer upstream flag SNOR_F_BROKEN_RESET
for devices with a flash chip that cannot be hardware reset with RESET pin
and therefore must be left in 3-byte address mode when idle.

The new patch requires that the DTS of affected devices
have the property "broken-flash-reset", which was not yet added for most of them.

This commit adds the property for remaining affected devices in ramips target,
specifically because of the flash chip model.

However, it is possible that there are other devices
where the flash chip uses an explicit 4-byte address mode
and the RESET pin is not connected to the SOC on the board,
and those DTS would also need this property.

Ref: 22d982ea00 ("ramips: add support for switching between 3-byte and 4-byte addressing")
Ref: dfa521f129 ("generic: spi-nor: rework broken-flash-reset")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
[pepe2k@gmail.com: backported to 21.02]
Fixes: #9655, #9636, #9547
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(backported from commit 74516f4357)
2022-04-08 10:31:32 +02:00
Hauke Mehrtens
39bf2aee0e kernel: bump 5.4 to 5.4.188
Added the new configuration options:
CONFIG_HARDEN_BRANCH_HISTORY=y
CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY=y

Manually adapted:
target/linux/generic/hack-5.4/220-gc_sections.patch

Compile-tested: lantiq/xrx200, armvirt/64
Run-tested: lantiq/xrx200, armvirt/64

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-04-07 20:42:34 +02:00
Petr Štetiar
3008f1f441 imagebuilder: fix broken image generation with external targets
When using external targets there is a symlink being created for the
target under target/linux which then becomes dangling under Image
Builder. Fix it by dereferencing the possible symlink.

Tested on IB with external target, ipq40xx and mvebu.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 621f39d1f4)
(cherry picked from commit ec9af870f3)
2022-04-05 22:06:41 +02:00
Jan-Niklas Burfeind
ee62912b2d
ath79: migrate Archer C5 5GHz radio device paths
When upgrading a TP-Link Archer C5 v1 from ar71xx to ath79,
the 5ghz radio stops working because the device path changed.

Same has been done for the Archer C7 before:

commit e19506f206 ("ath79: migrate Archer C7 5GHz radio device paths")

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
(cherry picked from commit c6eb63d48f)
2022-03-31 18:07:57 +02:00
Matthias Schiffer
f6513143ad
ath79: fix label MAC address for Ubiquiti UniFi AP Outdoor+
The label has the MAC address of eth0, not the WLAN PHY address. We can
merge the definition back into ar7241_ubnt_unifi.dtsi, as both DTS
derived from it use the same interface for their label MAC addresses
after all.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit aee9ccf5c1)
2022-03-30 17:49:43 +02:00
Christian Lamparter
5cf00adf21 apm821xx: fix crash/panic related to SATA/SSD choice
Ticerex on the OpenWrt Forum reported a gnarly crash when
he was using Samsung 840 and 850 EVOs with his MyBook Live:

| BUG: Kernel NULL pointer dereference at 0x00000000
| Faulting instruction address: 0xc03ed4b8
| Oops: Kernel access of bad area, sig: 11 [#1]
| BE PAGE_SIZE=4K PowerPC 44x Platform
| CPU: 0 PID: 362 Comm: scsi_eh_1 Not tainted 5.4.163 #0
| NIP:  c03ed4b8 LR: c03d27e8 CTR: c03ed36c
| REGS: cfa59950 TRAP: 0300   Not tainted  (5.4.163)
| MSR:  00021000 <CE,ME>  CR: 42000222  XER: 00000000
| DEAR: 00000000 ESR: 00000000
| GPR00: c03d27e8 cfa59a08 cfa55fe0 00000000 0fa46bc0 [...]
| [..]
| NIP [c03ed4b8] sata_dwc_qc_issue+0x14c/0x254
| LR [c03d27e8] ata_qc_issue+0x1c8/0x2dc
| Call Trace:
| [cfa59a08] [c003f4e0] __cancel_work_timer+0x124/0x194 (unreliable)
| [cfa59a78] [c03d27e8] ata_qc_issue+0x1c8/0x2dc
| [cfa59a98] [c03d2b3c] ata_exec_internal_sg+0x240/0x524
| [cfa59b08] [c03d2e98] ata_exec_internal+0x78/0xe0
| [cfa59b58] [c03d30fc] ata_read_log_page.part.38+0x1dc/0x204
| [cfa59bc8] [c03d324c] ata_identify_page_supported+0x68/0x130
| [...]

This turned out this is an issue with upstream changing
ATA_TAG_INTERNAL's value from 31 to 32 during 4.18 release.
Update "SATA_DWC_QCMD_MAX" to account for that.

Link: https://forum.openwrt.org/t/my-book-live-duo-reboot-loop/122464
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 5ac672cfab60e90ab8a0bf3491fa2a27619d22d6)
2022-03-26 21:26:07 +01:00
Marek Behún
0e5350db43 mvebu: SFP backports for GPON modules
This backports the following upstream Linux patches
  net: sfp: add mode quirk for GPON module Ubiquiti U-Fiber Instant
  net: sfp: relax bitrate-derived mode check
  net: sfp: cope with SFPs that set both LOS normal and LOS inverted
for 5.4 for mvebu platform.

This fixes GPON modules:
  Ubiquiti U-Fiber Instant SFP GPON
  VSOL V2801F
  CarlitoxxPro CPGOS03-0490 v2.0

Signed-off-by: Marek Behún <marek.behun@nic.cz>
2022-03-26 21:26:07 +01:00
Josef Schlehofer
52de8bf86e cypress-firmware: drop several packages
1. Drop package: cypress-firmware-4359-pcie
This binary is no longer provided and there are not many details what
happened.

2. Drop package: cypress-firmware-4359-sdio
This binary is no longer provided, but in this case, to compare it with
PCIe package mention as first, there was added
support in Linux-firmware [1], but no sign of firmware file.

4. Drop package: cypress-firmware-89459-pcie [2]
According to Infineon: "CYW89459 is an automotive Wi-Fi chip which is not
supported in the broad market community."

[1] https://patchwork.kernel.org/project/linux-wireless/patch/20191211235253.2539-6-smoch@web.de/

[2] https://community.infineon.com/t5/Wi-Fi-Bluetooth-for-Linux/the-wifi-driver-for-CYW89459-in-linux4-14-98-2-3-00/m-p/138971

Fixes: 7ca7e0b22d ("cypress-firmware:
update it to version 5.4.18-2021_0812")

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 8c66bf89d1)
2022-03-26 21:26:07 +01:00
Josef Schlehofer
41d36bb2d0 cypress-firmware: update it to version 5.4.18-2021_0812
- Binary files were renamed to cyfmac from brcmfmac, but the files needs
  to be on the router with the previous naming

[    6.656165] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[    6.665182] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.bin failed with error -2
[    6.674928] brcmfmac mmc1:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac43455-sdio.bin

- Cypress were acquired by Infineon Technologies
Thus change the project URL and switch to download files from their
GitHub repository. This is much better than the previous solution, which
requires finding new threads on their community forum about new driver
updates, and it will be necessary to change the URL each time.

Unfortunately, it seems that there is not published changelog, but
according to this forum thread [1], be careful by opening the link from
solution since it contains ending bracket ), it brings fixes for various
security vulnerabilities, which were fixed in 7_45_234.

Fixes:
- FragAttacks
- Kr00k

Also add LICENSE file

Run tested on Seeedstudio router powered by Raspberry Pi 4 CM with
package cypress-firmware-43455-sdio.

Before:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[    6.895050] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Mar 23 2020 02:20:01 version 7.45.206 (r725000 CY) FWID 01-febaba43

After:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[    6.829805] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Apr 15 2021 03:03:20 version 7.45.234 (4ca95bb CY) FWID 01-996384e2

[1] https://community.infineon.com/t5/Wi-Fi-Bluetooth-for-Linux/Outdated-brcmfmac-firmware-for-Raspberry-Pi-4-in-OpenWrt-21-02-1/m-p/331593#M2269

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 7ca7e0b22d)
2022-03-26 21:26:07 +01:00
David Bauer
cd17ca7d6f ath79: fix link for long cables with OCEDO Raccoon
The OCEDO Raccoon had significant packet-loss with cables longer than 50
meter. Disabling EEE restores normal operation.

Also change the ethernet config to reduce loss on sub-1G links.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4551bfd91f)
2022-03-26 19:09:17 +01:00
Matthias Schiffer
30e6f28853
ath79: fix TPLINK_HWREV field for TL-WR1043ND v4
Required to allow sysupgrades from OpenWrt 19.07.

Closes #7071

Fixes: 98fbf2edc0 ("ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloader")
Tested-by: J. Burfeind <git@aiyionpri.me>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 8ba71f1f6f)
2022-03-25 18:15:11 +01:00
Petr Štetiar
f65edc9b99 zlib: backport security fix for a reproducible crash in compressor
Tavis has just reported, that he was recently trying to track down a
reproducible crash in a compressor. Believe it or not, it really was a
bug in zlib-1.2.11 when compressing (not decompressing!) certain inputs.

Tavis has reported it upstream, but it turns out the issue has been
public since 2018, but the patch never made it into a release. As far as
he knows, nobody ever assigned it a CVE.

Suggested-by: Tavis Ormandy <taviso@gmail.com>
References: https://www.openwall.com/lists/oss-security/2022/03/24/1
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit b3aa2909a7)
(cherry picked from commit 3965dda0fa)
2022-03-24 09:40:12 +01:00
Petr Štetiar
fdd862f9ac sunxi: cortexa7: fix ethernet link detection on a20-olinuxino-lime2
a20-olinuxino-lime2 is currently having hard time with link detection of
certain 1000Mbit partners due to usage of generic PHY driver, probably
due to following missing workaround introduced in upstream in commit
3aed3e2a143c ("net: phy: micrel: add Asym Pause workaround"):

 The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
 Pause capability is set. This issue is described in a Silicon Errata
 (DS80000691D or DS80000692D), which advises to always disable the
 capability. This patch implements the workaround by defining a KSZ9031
 specific get_feature callback to force the Asymmetric Pause capability
 bit to be cleared.

 This fixes issues where the link would not come up at boot time, or when
 the Asym Pause bit was set later on.

As a20-olinuxino-lime2 has Micrel KSZ9031RNXCC-TR Gigabit PHY since
revision H, so we need to use Micrel PHY driver on those devices.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit ffa1088f63)
2022-03-24 09:40:12 +01:00
Robert Marko
4910ffa8e9 mvebu: udpu: include LM75 kmod by default
uDPU has 2 LM75 compatible temperature sensors, so include the driver for
them by default in order to utilize them.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase]
(cherry picked from commit a8b2d35903)
(cherry picked from commit b9e90935db)
2022-03-24 09:40:12 +01:00
Robert Marko
d38f7ec56f mvebu: udpu: fix initramfs booting
uDPU provides a FIT based initramfs, but currently gets stuck after U-boot
starts the kernel at "Starting kernel..".

It is due to the load address being too low, so increase it in order to get
the initramfs booting again.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 80f21e5336)
(cherry picked from commit d65269a732)
2022-03-24 09:40:12 +01:00
Matthias Schiffer
56d69ee70d
ath79: fix label MAC address for Ubiquiti UniFi
The label has the MAC address of eth0, not the WLAN PHY address.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 2a02b70499)
2022-03-24 09:35:55 +01:00
Felix Fietkau
c6256a6533 ramips: remove kmod-mt7663-firmware-sta from device packages
This firmware should only be used for mobile devices (e.g. laptops), where
AP mode functionality is typically not used. This firmware supports a lot
of power saving offload functionality at the expense of AP mode support.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a1ac8728f8)
2022-03-23 12:52:20 +00:00
Marek Behún
28343cfb7d kernel: backport DSA patches fixing null-pointer dereference
[ backport of master commit fbe2c3feaa ]

Backport patches
  381a730182f1 ("net: dsa: Move VLAN filtering syncing out of dsa_switch_bridge_leave")
  108dc8741c20 ("net: dsa: Avoid cross-chip syncing of VLAN filtering")
from upstream (currently in net-next) to fix null-pointer dereference.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [master commit detail]
2022-03-21 14:23:42 +01:00
David Bauer
180b750c02 hostapd: add STA extended capabilities to get_clients
Add the STAs extended capabilities to the ubus STA information. This
way, external daemons can be made aware of a STAs capabilities.

This field is of an array type and contains 0 or more bytes of a STAs
advertised extended capabilities.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 6f78723977)
2022-03-20 01:32:36 +01:00
David Bauer
411c73f748 hostapd: add op-class to get_status output
Include the current operation class to hostapd get_status interface.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2a31e9ca97)
2022-03-20 01:32:06 +01:00
David Bauer
e44a781e11 hostapd: add beacon_interval to get_status ubus output
Add the beacon interval to hostapd status output. This allows external
services to discover the beacon interval for a specific VAP.

This way, external wireless management daemons can correctly calculate
fields containing TBTT value from absolute time-values.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3ba9846842)
2022-03-20 01:31:47 +01:00
Martin Weinelt
95b0b8725c hostapd: remove unused mac_buff allocation
Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
(cherry picked from commit cde154c871)
2022-03-20 01:31:21 +01:00
Martin Weinelt
3731ffa0ee hostapd: report bssid, ssid and channel over ubus
Imports a function from iw to convert frequencies to channel numbers.

Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
[fix potential out of bounds read]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 398df62756)
2022-03-20 01:30:52 +01:00
David Bauer
53c60d4bfa hostapd: ubus: add notification for BSS transition response
To allow steering daemons to be aware of the STA-decided transition
target, publish WNM transition responses to ubus. This way, steerings
daemons can learn about STA-chosen targets and send a better selection
of transition candidates.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit a3de42e72c)
2022-03-20 01:29:59 +01:00
David Bauer
88075c87dc hostapd: ubus: add BSS transtiton request method
The existing wnm_disassoc_imminent ubus method only supports issuing a
bss transition request with the disassoc imminent flag set.
For use-cases, where the client is requested to roam to another BSS
without a pending disassoc, this existing method is not suitable.

Add a new bss_transition_request ubus method, which provides a more
universal way to dispatch a transition request. It takes the following
arguments:

Required:
addr: String - MAC-address of the STA to send the request to (colon-seperated)

Optional:
abridged - Bool - Indicates if the abridged flag is set
disassociation_imminent: Bool - Whether or not the disassoc_imminent
                         flag is set
disassociation_timer: I32 - number of TBTTs after which the client will
                      be disassociated
validity_period: I32 - number of TBTTs after which the beacon
                 candidate list (if included) will be invalid
neighbors: blob-array - Array of strings containing neighbor reports as
           hex-string

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 0eed96ca5d)
2022-03-20 01:29:09 +01:00
Martin Schiller
b1c3539868 openssl: bump to 1.1.1n
This is a bugfix release. Changelog:

  *) Fixed a bug in the BN_mod_sqrt() function that can cause it to loop
     forever for non-prime moduli. (CVE-2022-0778)

  *) Add ciphersuites based on DHE_PSK (RFC 4279) and ECDHE_PSK
     (RFC 5489) to the list of ciphersuites providing Perfect Forward
     Secrecy as required by SECLEVEL >= 3.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
(cherry picked from commit e17c6ee627)
2022-03-16 16:30:21 +01:00
Rafał Miłecki
864bba55d8 uboot-bcm4908: use "xxd" from staging_dir
This fixes:
bash: xxd: command not found
on hosts without xxd installed.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 9dbca6bf6e)
Fixes: 45b3f2aa0f ("uboot-bcm4908: add package with BCM4908 U-Boot")
2022-03-15 18:55:08 +01:00
Daniel Golle
92020d4242 tools: xxd: use more convenient source tarball
Don't download all of vim just to build xxd. Use a tight tarball
containing only xxd sources instead.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 2b94aac7a1)
2022-03-15 18:50:32 +01:00
Daniel Golle
17e9553284 tools: add xxd (from vim)
U-Boot requires xxd to create the default environment from an external
file as done in uboot-mediatek.
Build xxd (only, not the rest of vim) as part of tools to make sure it
is present on the buildhost.

Reported-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit c4dd2441e7)
2022-03-15 18:50:26 +01:00