Currently kmod-i2c-mux-* will not get into images unless kmod-i2c-mux is added
to DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-i2c-mux-pca954x
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
As it seeems these patches are for OpenWrt and they are not going to be merged
to mainline, let's merge them to improve maintainability.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Follow the guideline suggested in e417ff88f1 ("ramips: harmonize line breaks
in image Makefiles").
While at it, fix typos in the device title of Akitio MyCloud.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The mux need to be defined in a subnode to be considered by the pinctrl
framework. These muxes aren't set as expected and might cause not
working subsystems.
Fixes: 8e7b573b7a ("lantiq: dts: assign the PCI pins to the PCI controller node")
Fixes: dcb5e52209 ("lantiq: dts: assign the STP pins to the STP GPIO controller node")
Fixes: 660200e53d ("lantiq: dts: assign the GPHY LED pins to the Ethernet controller node")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Lets enable RAW NAND and Qcom NANDC drivers again in kernel 5.4.
They were dropped when 5.4 support was introduced due to upstream
changing the symbol names so refreshing was not enough.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[cut long line in commit message, enabled BCH as well]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Fixes following error uncovered while building ath79/tiny on 5.4:
Package kmod-hwmon-sch5627 is missing dependencies for the following
libraries:
watchdog.ko
See the similar commit e546e6252b ("malta: fix missing watchdog core
dependency for hwmon-sch5627") for a detailed explanation.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Ansuel Smith <ansuelsmth@gmail.com> [wrt3200acm @ 5.4]
The TP-Link RE450 as well as the UniFi AC series missed the phy-mode
property. Because of this, the incorrect MII phy-mode from the root dtsi
was used.
With Kernel 5.4, this leads to problems when used with a AR8033 PHY. The
bootloader seems to leave the fiber pages selected.
As there's not switch to copper pages happening in at803x_config_init
due to the incorrect phy-mode, the new at803x_read_status will interpret
the status of the SGMII side as the status of the copper side.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch removes the 4.14 kernel support from the apm821xx target.
The 4.19 kernel has been available and stable for a while and the 5.4
kernel support has been tested successfully on real hardware as well.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The ag71xx driver from Linux 5.4 currently has various shortcomings
when used with OpenWrt compared to our downstream version.
For example, the upstream driver does not support modifying the ethernet
clock and configuring RGMII delays on the MAC side.
While we should certainly switch to the upstream driver, the amount of
necessary patches would make it cumbersome to work with. It's also
highly likely we won't be able to finish patching the upstream driver in
time for a Linux 5.4 release.
Tested on Siemens WS-AP3610.
CC: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently kmod-i2c-* will not get into images unless kmod-i2c-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-lm75
- kmod-i2c-gpio
- kmod-i2c-gpio-custom
- kmod-i2c-mux
- kmod-i2c-ralink
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently kmod-hwmon-* will not get into images unless kmod-hwmon-core is added
to DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-gpiofan
- kmod-hwmon-lm63
- kmod-hwmon-lm75
- kmod-hwmon-lm85
- kmod-hwmon-lm90
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, adjust line wrapping]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TOTOLINK A3 is a clone of ipTIME A3. The only difference is the model name.
Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
- Switch: SoC internal
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Tested on device by JasonHCH <hsuan670629@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This adds support for the TP-Link TL-WR740N v5, a clone of the
v4 only with a different TPLINK_HWID. It was already supported
in ar71xx as well.
Specifications:
SOC: Atheros AR9331
CPU: 400MHz
Flash: 4 MiB
RAM: 32 MiB
WLAN: Atheros AR9330 bgn
Ethernet: 5 ports (100M)
Flashing instructions:
- Flash factory image from OEM WebUI:
openwrt-ath79-tiny-tplink_tl-wr740n-v5-squashfs-factory.bin
- Sysupgrade from ar71xx image:
openwrt-ath79-tiny-tplink_tl-wr740n-v5-squashfs-sysupgrade.bin
Signed-off-by: Jun Su <howard0su@gmail.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The NAND config symbols were removed unintentionally while adding
support for Linux 5.4.
Add the respective symbols for v4.19 as well as v5.4.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds support for GW5907/GW5910/GW5912/GW5913 IMX6 based boards
from the Gateworks Ventana Family[A]:
- backport upstream dt patches from 5.6 to 4.19 and 5.4
- add dtb's to ventana images
- add board-name and network config
A. https://www.gateworks.com/products/imx6-single-board-computer-gateworks-ventana-family
Flashing instructions for Ventana boards:
Using pre-flashed bootloader:
- Use appropriate ubi image depending on board NAND to flash via bootloader:
openwrt-imx6-ventana-squashfs-nand.ubi - 2KiB page size
openwrt-imx6-ventana-large-squashfs-nand.ubi - 4KiB page size
http://trac.gateworks.com/wiki/linux/ubi
Using Gateworks JTAG dongle:
- Use Gateworks mkimage_jtag script to create a JTAG image comprised of
pre-built bootloader and ubi image:
http://trac.gateworks.com/wiki/jtag_instructions
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The wildcard used in the network config matching is not necessary
given the board names returned by imx6_board_detect() in lib/imx6.sh.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Require the image metadata check so no invalid image could be fed to
sysupgrade without force option.
Cc: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Instead of dangerous rewriting full chip with firmware.bin image to
update OpenWrt, add sysupgrade image. This image will be used to update
kernel and rootfs, leaving bootloader intact and making recovery
possible, without resorting to external hardware tools.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Combine fixed sizes of "kernel" and "rootfs" partitions into one
partition managed by OpenWrt splitter, it will allow better management
of chip capacity and less maintenance burden when compiled kernel image
will outgrow allocated size for kernel partition. This also changes kernel
image format, since splitter only manages kernel and rootfs partitions,
the dtb needs to be updated with the kernel, so for convenience, kernel is
packed to FIT image.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This commit replaces UBIFS root partition with squashfs+overlay. It's
preparation for introducing dynamic partitioning.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Uncompressing of initramfs image fails on board with U-Boot from "QorIQ
SDK (FSL Reference Distro) 2.0".
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Re-add support for NXP FRDM-LS1012A, which mimics the flash layout of the
rest boards supported by LSDK.
0x000000000000-0x000000100000 : "bl2"
0x000000100000-0x000000500000 : "fip"
0x000000500000-0x000000600000 : "u-boot-env"
0x000000600000-0x000000a00000 : "reserved-1"
0x000000a00000-0x000000d00000 : "pfe"
0x000000d00000-0x000000f00000 : "reserved-2"
0x000000f00000-0x000001000000 : "dtb"
0x000001000000-0x000002000000 : "kernel"
0x000002000000-0x000004000000 : "ubifs"
Specification
SoC: LS1012A single core 800MHz
RAM: 512 MB DDR3
Flash: 64 MB QSPI NOR
Ethernet: 2x 10/100/1000 Mbps
Connectors: µUSB 3.0 OTG
µUSB 2.0 (debugging & power input)
2x 3.5mm jack for microphone & headphone (SGTL5000)
Arduino Shield expansion with I2C, SPI, UART, and GPIO
JTAG
LEDS: 3x (non-configurable)
Buttons: 1x (reset, non-configurable)
Be advised that erasing or writing 64MB flash takes some time to finish.
Do not reset the board until all operations end with success, otherwise
You'll need external tools to re-program the flash chip.
Installation
Follow the QSPI programing procedure for LS1012AFRWY board in
target/linux/layerscape/README, point 3.3.
Don't forget about updating U-Boot environment with MAC addresses of
ethernet interfaces, variable 'ethaddr' for eth0 and 'eth1addr' for eth1.
As the LSDK images do not support sysupgrade, nor do changes in this
commit, it's planed in upcoming submissions.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This patch adds a few symbols that I found that
need disabling in order to not break the build of octeontx
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This patch backports the upstream patch that adds the 4B_OPCODES flag to w25q256 under 5.4 kernel.
This is needed for ipq40xx and ramips.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch backports the upstream patch that adds the 4B_OPCODES flag to w25q256 under 4.19 kernel.
This is needed for ipq40xx and ramips.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Run-tested 5.4 on Shuttle KD20 for some days now, everything seems
fine so far. Let's have snapshot builds based on 5.4.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Currently kmod-ata-* will not get into images unless kmod-ata-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-ata-ahci
- kmod-ata-ahci-mtk
- kmod-ata-sunxi
While at it, use AddDepends/ata for kmod-ata-pdc202xx-old.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
All SUNXI_UBOOT usages were removed in e018c4d7ab ("uboot-sunxi: clean up,
switch to u-boot.mk"). Now drop the variable completely.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
DTS variable is not used in any device. Just drop it.
UBIFS_OPTS is not device-dependent here. Remove it from DEVICE_VARS.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
IMAGE_SIZE is widely used in many targets. Declare it in the default template to
clean up redundant code. This also prevents deriving IMAGE_SIZE unintentionally
from the previously defined device.
While at it, remove duplicate KERNEL_SIZE declaration.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The labels on the LAN ports of the TP-Link Archer C60 v1/v2 are
actually inverted compared to the ports of the internal switch.
Add this information to 02_network.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The labels on the LAN ports of the TP-Link Archer C60 v1/v2 are
actually inverted compared to the ports of the internal switch.
Add this information to 02_network.
This is the same for to-be-supported v3 of this device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The adjustment of the MAC address for Archer C60 v2 in 10_fix_wifi_mac
is broken since a "mac" partition is not set up for this device on
ar71xx. Instead, the MAC address is already patched correctly in
11-ath10k-caldata.
Remove the useless adjustment.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MAC addresses for lan/wan are swapped compared to the vendor
firmware. This adjusts to vendor configuration, which is:
lan *:7b label
wan *:7c label+1
2.4g *:7b label
5g *:7a label-1
Only one address is stored in <&mac 0x8>, corresponding to the label.
This has been checked on revisions v1, v2 and v3.
Since ar71xx calculates the ath10k MAC address based on the ethernet
addresses, the number there is adjusted, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MAC addresses for lan/wan are swapped compared to the vendor
firmware. This adjusts to vendor configuration, which is:
lan *:7b label
wan *:7c label+1
2.4g *:7b label
5g *:7a label-1
Only one address is stored in <&mac 0x8>, corresponding to the label.
This has been checked on revisions v1, v2 and v3.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fixes following error uncovered while building armvirt/64 on 5.4:
Package kmod-hwmon-sch5627 is missing dependencies for the following libraries:
watchdog.ko
That dependency was introduced in upstream via 2d8c7ff52c24
("hwmon/sch56xx: Depend on watchdog for watchdog core functions") in
v3.5.
The issue emerged in 5.4 because the kconfig symbol CONFIG_WATCHDOG_CORE
is now a tristate value. Previously it was a bool.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
SoC: MediaTek MT7621AT
WiFi: MediaTek MT7603 bgn 2T2R
MediaTek MT7615 ac 4T4R
Flash: 32M SPI (Macronix MX25L25635F)
RAM: 128M DDR3 (Winbond W631GG6KB)
LED: Dome (Blue / White)
BTN: Reset
Installation
------------
These instructions were written for firmware version v3.9.27.
Downgrade if necessary.
1. Copy the OpenWrt sysupgrade image to the devices /tmp folder
via scp. On factory defaults, user and password is "ubnt" at
192.168.1.20/24.
2. Write the bootselect flag. Otherwise, the device might boot from the
wrong partition. Verify the mtd partition used in the command below
is the one labled "bs" in /proc/mtd (as this might change in the
future).
> dd if=/dev/zero bs=1 count=1 of=/dev/mtd4
3. Write the OpenWrt sysupgrade to the mtd partitions labled
"kernel0" and "kernel1".
> dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock6
> dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock7
4. Reboot or powercycle the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Ethernet, switch, LEDs, buttons, USB, sysupgrade & LuCI were
successfully tested on BCM4706.
WARNING: Hack for BCM4710 adding BCM4710_PROTECTED_FILL_TLB() to the
local_r4k_flush_cache_sigtramp() could not be ported. That function has
been dropped in:
commit adcc81f148d7 ("MIPS: math-emu: Write-protect delay slot emulation pages")
commit 3315b6b336c8 ("MIPS: Delete unused flush_cache_sigtramp()")
it's unsure if that chipset will still work reliably.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Generate a cpximg that is compatible with the cpximg loader in Compex' u-boot.
The cpximg loader can be started either by holding the reset button during power
up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept an image
appropriate for the board revision that is etched on the board (e.g. 6A04).
The image can be pushed using tftp:
tftp -v -m binary 192.168.1.1 -c put openwrt-ipq40xx-generic-compex_wpj428-squashfs-cpximg-6a04.bin
cpximg files can also be used with the sysupgrade utility in stock images.
(add SSH key in luci for root access)
In mkmylofw_32m, the calculation of the "partition size" has been preferred
to just padding the partition as this will result in less block transfers
during flashing (while the additional complexity is bearable).
Signed-off-by: Leon M. George <leon@georgemail.eu>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fixes following error uncovered while building malta/be on 5.4:
Package kmod-hwmon-sch5627 is missing dependencies for the following libraries:
watchdog.ko
That dependency was introduced in upstream via 2d8c7ff52c24
("hwmon/sch56xx: Depend on watchdog for watchdog core functions") in
v3.5.
The issue emerged in 5.4 because the kconfig symbol CONFIG_WATCHDOG_CORE
is now a tristate value. Previously it was a bool
Cc: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(drop the config-4.19 change. reword about the cause)
Hardware
--------
SoC: MediaTek MT7620A
RAM: 64MB
FLASH: 8MB SPI
WLAN: 2G: MediaTek MT7620A
5G: MediaTek MT7610EN
ETH: 1x 10/100/1000M (Atheros AR8035)
LED: RSSI (orange/green)
WiFi 2G (green)
WiFi 5G (green)
Power (green)
System (red / green)
BTN: Power
Reset
LED
WPS
Serial
------
P1 - Tx
P2 - Rx
P3 - GND
P4 - VCC
Pin 4 is the one closest to the LAN port.
MAC overview
------------
WAN *:4c uboot 0x1fc00
2.4 *:4c uboot 0x1fc00
5 *:4e uboot 0x1fc00 +2
Installation
------------
Web interface:
It is possible to upgrade to OpenWrt via the web interface. However, the
OEM firmware upgrade file is required and a tool to fix the MD5 sum of
the header. This procedure overwrites U-Boot and there is not failsafe /
recovery mode present! To prepare an image, you need to take the header
and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and
attach the factory image to it. Then fix the header MD5Sum1.
Serial/TFTP:
You can use initramfs for booting via RAM or flash the image directly.
Additional Notes:
If the web interface upgrade fails, you have to open your device and
attach serial console. Since the web upgrade overwrites the boot loader,
you might also brick your device.
In order to flash back to stock, the first header and U-Boot needs to be
stripped from the original firmware.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[change rssi LED labels]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the 8devices Habanero development board.
Specs are:
CPU: QCA IPQ4019
RAM: DDR3L 512MB
Storage: 32MB SPI-NOR and optional Parallel SLC NAND(Some boards ship with it and some without)
WLAN1: 2.4 GHz built into IPQ4019 (802.11n) 2x2
WLAN2: 5 GHz built into IPO4019 (802.11ac Wawe-2) 2x2
Ethernet: 5x Gbit LAN (QCA 8075)
USB: 1x USB 2.0 and 1x USB 3.0 (Both built into IPQ4019)
MicroSD slot (Uses SD controller built into IPQ4019)
SDIO3.0/EMMC slot (Uses the same SD controller)
Mini PCI-E Gen 2.0 slot (Built into IPQ4019)
5x LEDs (4 GPIO controllable)
2x Pushbutton (1 is connected to GPIO, other to SoC reset)
LCD ZIF socket (Uses the LCD controller built into IPQ4019 which has no driver support)
1x UART 115200 rate on J18
2x breakout development headers
12V DC Jack for power
DIP switch for bootstrap configuration
Installation instructions:
Since boards ship with vendors fork of OpenWrt sysupgrade can be used.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit finally adds support for the built in SD/MMC controller in IPQ4019 SoC.
Controller is supported by the upstream SDHCI-MSM driver with a minor clock setting patch.
Patch is special to the IPQ4019 and cannot be upstreamed.
LDO and SDHCI node are upstreamed, and LDO node is awaiting to be accepted.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing kernel config symbol probably some dependency uncovered by
my local perf related and enabled kernel config options.
ARM PMU framework (ARM_PMU) [Y/n/?] y
Freescale i.MX8 DDR perf monitor (FSL_IMX8_DDR_PMU) [N/m/y/?] (NEW)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
I've added `set_blkcnt` environment variable which is needed for every
`mmc write` command as we need to always specify size in block count.
That `set_blkcnt` variable was previously present in the U-Boot's
default environment, but that needed patching U-Boot every time, so that
patch was dropped with 2020.01 version bump.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
U-Boot 2020.01 has changed names for same variables, adjust the
bootscript accordingly. Added boot_file variable as the default value is
zImage.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Adds into 4.19 backported kernel module from 5.1 for Sensirion SPS30
particulate matter sensor, for kernel 5.4 backported dependency fix.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 15a0701cdd.
It was reported that this patch breaks on some cases the JFFS2 overlay
filesystem on targets still using kernel 4.14. This includes ar71xx,
where spurious erase of the ART was reported.
Revert this commit for now. Re-adding should probaby also be done for
every currently supported kernel version.
Ref: FS#2837 FS#2862 FS#2864
Signed-off-by: David Bauer <mail@david-bauer.net>
This applies the common indent (one tab) for the wrapped lines of
domywifi_dw33d and glinet_gl-ar750s-nor-nand.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
patches-4.14/340-oxnas-pcie.patch was adapted for kernel 5.4 by
accident. Revert that change to restore 4.14 builds.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Sitecom WLR-8100 v1 002 (marketed as X8 AC1750) is a dual band wireless
router.
Specification:
- Qualcomm Atheros SoC QCA9558
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (Macronix MX25L12845EMI-10G - SPI NOR)
- 5x 10/100/1000 Mbps Ethernet
- 3T3R 2.4 GHz (QCA9558 WMAC)
- 3T3R 5.8 Ghz (QCA9880-BR4A)
- 1x USB 3.0 (Etron EJ168A)
- 1x USB 2.0
- 9x LEDs
- 2x GPIO buttons
Everything working.
Installation and restore procedure tested
Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Toolbox > Firmware,
4. Browse for OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
is ready for configuration.
Restore OEM FW (Linux only)
1. Download OEM FW from website (tested with WLR-8100v1002-firmware-v27.dlf)
2. Compile the FW for this router and locate the "mksenaofw" tool
in build_dir/host/firmware-utils/bin/ inside the OpenWrt buildroot
3. Execute "mksenaofw -d WLR-8100v1002-firmware-v27.dlf -o WLR-8100v1002-firmware-v27.dlf.out" where:
WLR-8100v1002-firmware-v27.dlf is the path to the input file
(use the downloaded file)
WLR-8100v1002-firmware-v27.dlf.out is the path to the output file
(you can use the filename you want)
4. Flash the new WLR-8100v1002-firmware-v27.dlf.out file. WARNING: Do not keep settings.
Additional notes.
The original firmware has the following button configuration:
- Press for 2s the 2.4GHz button: WPS for 2.4GHz
- Press for 2s the 5GHz button: WPS for 5GHz
- Press for 15s both 2.4GHz and 5GHz buttons: Reset
I am not able to replicate this behaviour, so I used the following configuration:
- Press the 2.4GHz button: RFKILL (disable/enable every wireless interfaces)
- Press the 5GHz button: Reset
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
This patch support Devolo Magic 2 WIFI, board devolo_dlan2-2400-ac.
This device is a plc wifi AC2400 router/extender with 2 Ethernet
ports, has a G.hn PLC and uses LCMP protocol from Home Grid Forum.
Hardware:
SoC: AR9344
CPU: 560 MHz
Flash: 16 MiB (W25Q128JVSIQ)
RAM: 128 MiB DDR2
Ethernet: 2xLAN 10/100/1000
PLC: 88LX5152 (MaxLinear G.hn)
PLC Flash: W25Q32JVSSIQ
PLC Uplink: 1Gbps MIMO
PLC Link: RGMII 1Gbps (WAN)
WiFi: Atheros AR9340 2.4GHz 802.11bgn
Atheros AR9882-BR4A 5GHz 802.11ac
Switch: QCA8337, Port0:CPU, Port2:PLC, Port3:LAN1, Port4:LAN2
Button: 3x Buttons (Reset, wifi and plc)
LED: 3x Leds (wifi, plc white, plc red)
GPIO Switch: 11-PLC Pairing (Active Low)
13-PLC Enable
21-WLAN power
MACs Details verified with the stock firmware:
Radio1: 2.4 GHz &wmac *:4c Art location: 0x1002
Radio0: 5.0 GHz &pcie *:4d Art location: 0x5006
Ethernet ðernet *:4e = 2.4 GHz + 2
PLC uplink --- *:4f = 2.4 GHz + 3
Label MAC address is from PLC uplink
OEM SSID: echo devolo-$(grep SerialNumber /dev/mtd1 | grep -o ...$)
OEM WiFi password: grep DlanSecurityID /dev/mtd1|tr -d -|cut -d'=' -f 2
Recommendations: Configure and link your PLC with OEM firmware
BEFORE you flash the device. PLC configuration/link should
remain in different memory and should work straight forward
after flashing.
Restrictions: PLC link detection to trigger plc red led is not
available. PLC G.hn chip is not compatible with open-plc-tools,
it uses LCMP protocol with AES-128 and requires different
software.
Notes: Pairing should be possible with gpio switch. Default
configuration will trigger wifi led with 2.4Ghz wifi traffic
and plc white led with wan traffic.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.100
2. Download the sysupgrade image and rename it to uploadfile
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Allow 1-2 minutes for the first boot.
Signed-off-by: Manuel Giganto <mgigantoregistros@gmail.com>
This commit ports the device from ar71xx to the ath79 target and
modifies the partition layout.
1. Firmware is installed to nand flash.
2. Modify the uboot-env parameter to boot from the nand flash.
3. The kernel size is extended to 5M.
4.nor flash retains the oem firmware.
oem partition layout
dev: size erasesize name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00e30000 00010000 "rootfs"
mtd3: 00170000 00010000 "kernel"
mtd4: 00010000 00010000 "art"
mtd5: 00f90000 00010000 "firmware"
mtd6: 06000000 00020000 "rootfs_data"
mtd7: 02000000 00020000 "backup"
new partition layout
dev: size erasesize name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00fa0000 00010000 "oem-firmware"
mtd3: 00010000 00010000 "art"
mtd4: 00500000 00020000 "kernel"
mtd5: 05b00000 00020000 "ubi"
mtd6: 02000000 00020000 "oem-backup"
MAC address overview:
All mac addresses are stored in the art partition.
eth0: 0x0
eth1: 0x6
ath9k: 0xc
ath10k: 0x12
No valid addresses in 0x1002 and 0x5006. All addresses match the OEM
firmware.
Install from oem firmware.
Enable ssh service:
Connect to the router web, click professional, click system-startup,
and add dropbear in the local startup input box. Click
system-administration, delete ssh-key, and replace your ssh pub key.
Restart the router.
1.Upload openwrt firmware to the device
scp openwrt-snapshot-r11365-df60a0852c-ath79-nand-domywifi_dw33d-\
squashfs-factory.bin root@192.168.10.1:/tmp
2.modify uboot-env.
ssh login to the device:
fw_setenv bootcmd 'nboot 0x8050000 0;bootm || bootm 0x9fe80000'
Run the fw_printenv command to check if the settings are correct.
3.Write openwrt firmware.
ssh login to the device:
mtd -r write /tmp/openwrt-snapshot-r11365-df60a0852c-ath79-nand-\
domywifi_dw33d-squashfs-factory.bin /dev/mtd6
The device will restart automatically and the openwrt firmware
installation is complete.
Restore oem firmware.just erase the kernel partition and the ubi
partition.
ssh login to the device:
mtd erase /dev/mtd4
mtd -r erase /dev/mtd5
Reboot the device
Signed-off-by: WeiDong Jia <jwdsccd@gmail.com>
[alter flash instruction in commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Add 5.4 kernel version as a new testing kernel option.
Run-tested on Shuttle KD20, seems to work just as well as kernel 4.14.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Patch 0061-tty-serial-ar933x-uart-rs485-gpio.patch wasn't included
when adding support for kernel 5.4. Re-add it and refresh patches.
Fixes: 53ab9865c2 ("ath79: add support for kernel 5.4")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Read times drop when increasing frequency to 25 MHz and 50 MHz,
but not in between or for further increase. So, use 50 MHz as the
lowest frequency with the fastest speed.
Test results (thanks to Roger):
The device reports a mx25l6405d flash chip. I tried all the maximum
values in the devices' datasheet (Table 10. AC CHARACTERISTICS). All of
them worked with and without "m25p,fast-read":
> 10 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 1m 33.00s
user 0m 0.01s
sys 1m 7.56s
> 25 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 34.42s
user 0m 0.02s
sys 0m 23.58s
> 25 MHz, fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 34.45s
user 0m 0.02s
sys 0m 23.59s
> 33 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 34.39s
user 0m 0.00s
sys 0m 23.60s
> 33 MHz, fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 34.46s
user 0m 0.01s
sys 0m 23.62s
> 50 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.81s
user 0m 0.01s
sys 0m 18.25s
> 50 MHz, fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.84s
user 0m 0.00s
sys 0m 18.25s
> 66 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.80s
user 0m 0.01s
sys 0m 18.23s
> 66 MHz, fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.80s
user 0m 0.02s
sys 0m 18.23s
> 86 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.84s
user 0m 0.01s
sys 0m 18.24s
> 86 MHz, fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.80s
user 0m 0.02s
sys 0m 18.23s
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch addresses several issues for D-Link DIR-810L:
- add correct button codes
- harmonize button node names
- use generic flash@0
- remove unused pin groups from state_default
- improve sorting of properties
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
The Jffs2 partition for the D-Link DIR-810L is currently off by
0x10000. Apply the correct offset based on the other partitions'
size/offset and the information about stock OS from the Wiki.
This is just based on the named information and _not_ verified
on device.
Fixes: 36e3424fa5 ("ramips: add support for dir810l and asus rp-n53")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This fixes a typo in the device string for MAC address setup in
02_network and corrects the indent in the device's DTS files.
While at it, move the aliases section before the keys section to
have it closer to the top of the file.
Fixes: a736d912e2 ("ipq40xx: add support for EnGenius EAP2200")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the Netgear R6800, aka Netgear AC1900 and
R6800-100PES.
Specification:
- SoC: MediaTek MT7621AT (880 MHz)
- Flash: 128 MiB NAND
- RAM: 256 MiB
- Wireless: MediaTek MT7615EN b/g/n , MediaTek MT7615EN an+ac
- LAN speed: 10/100/1000
- LAN ports: 4
- WAN speed: 10/100/1000
- WAN ports: 1
- USB 2.0
- USB 3.0
- Serial baud rate of Bootloader and factory firmware: 57600
Known issues:
- Device has 3 wifi LEDs: Wifi 5Ghz, Wifi 2.4Ghz and Wifi on/off.
Wifi on/off is not used.
Installation:
- apply factory image via stock web-gui.
Back to stock:
- nmrpflash can be used to recover to the stock Netgear firmware.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Add 5.4 kernel version as a new testing kernel option.
Ref: https://github.com/openwrt/openwrt/pull/2793
Tested-by: Hannu Nyman <hannu.nyman@iki.fi> [ipq8065, R7800]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065, NBG6817]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[added Tested-by tags]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Due to changes in syscon driver, the phy dwc3 driver
needs to use device_node_to_regmap since it has to skip
the new introduced clk check. This fix broken usb3 on this
target.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
As mdio0 is used in every dts move it to general ipq8064
dts and use label to set device specific definition.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Currently the watchdog timer is broken as it tries to
get an interrupt to setup pretimeout. Since our platform
have a different type of interrupt disable it and use
legacy watchdog probe.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This was created by Chunkeey some time ago. Since mdio driver
works or doesn't work and since this was tested by me for 1 year,
include it to remove the use of the generic bitbang gpio driver for
switch driver.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework tsens driver.
Since in the new kernel 5.4 init common do more than it
should, inizialize the kernel memory directly in the driver and
drop use of this function. Rework all the patch with the new
variable names.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework l2 scaling patch to fix some compile warning
and to imporve the caling timings by removing call to unnecessary
function.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Since this dtsi now have wrong definition in the upstream version,
include it to overwrite and remove any problem.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
5.4 support is ready and tested.
Compile tested: all target devices
Run tested: pogoplug v4, nsa310b and two unofficial supported devices
Tested-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Alberto Bursi <alberto.bursi@outlook.it> [pogoplug v4 and nsa310b]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed the switch, removed maintainer variable]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Changes made in switch nodes in d42c9ce commit causes problem with
correct mvsw61xx detection. This commit undo that changes.
mvsw61xx is platform driver, so it need to be in main root of dts.
Fixes: d42c9ce326 ("kirkwood: add kernel 4.19 support")
Tested-by: Marcin Fedan <mfedan@gmail.com> [EA4500]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This commit is simple copy config, files and patches from 4.19 to 5.4
kernel. No changes was done.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Leave as enabled by default for mediatek. Also remove obsolete
settings from when packet steering was moved from netifd to a
simplified hotplug script.
Signed-off-by: Alan Swanson <reiver@improbability.net>
Global attributes enable_mirror_tx/enable_mirror_rx depend on runtime
value of another global attribute mirror_source_port which just resides
in the memory
The same functionality can be achieved by directly setting port
attribute of the same names. E.g. the following two groups of commands
achieve the same thing
swconfig dev switch0 set mirror_source_port 3
swconfig dev switch0 set enable_mirror_tx 1
swconfig dev switch0 set mirror_source_port 4
swconfig dev switch0 set enable_mirror_tx 1
swconfig dev switch0 port 3 set enable_mirror_tx 1
swconfig dev switch0 port 4 set enable_mirror_tx 1
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Image building process was missing "asus-trx" step which resulted in raw
TRX files (without ASUS footer with device id).
Fixes: 0b9de8daa7 ("bcm53xx: add profiles for all other (SoftMAC) devices")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
When changing the LED names for the Archer C7 to represent the correct
color, a migration for existing UCI entries was not created.
Add a migration to keep existing LED configurations working.
Fixes commit c79c001b59 ("ar71xx: Archer C7 v1 LED names and RFKILL
fixes")
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit fills the void for current OpenWrt installations which will
be still on old bootloader version even after "x86: add bootloader
upgrade on sysupgrade", since it performs bootloader upgrade only on
sysupgrade. To keep all OpenWrt deploynents on the same GRUB version,
add preinit hook, which will perform upgrade of the bootloader on first
boot after sysupgrade.
It's temporary solution and should be deleted, when the first release
including this hook will no longer be supported by OpenWrt team.
We can assume that all installations should be on current bootolader
version and from there sysupgrade routine will be sufficient.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Currently bootloader always stays on the same version as when first
written to boot medium (not true if partition layout changed, which will
trigger sysupgrade process to write full disk image). That creates
inconveniences as it always stays with same features or/and bugs. Users
wishing to add support to additional modules or new version, would need
to write the whole image, potentially destroying previous system
configuration. To fix these, this commit adds additional routine to
sysupgrade which upgrades unconditionally the bootloader to the latest
state provided by OpenWrt.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
There can be some leftovers from other image recipes, if the same
directory names are used and multiply image types are selected.
Therefore remove directories used in the recipe, before contents for the
image are prepared.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Add one node for the accel/gyro i2c device and another for the separate
magnetometer device in the lsm9ds1.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
[commit subject/description tweaks, kernel version in patch filename]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Backport kernel module from 5.5 for FXOS8700CQ, which is a small,
low-power, 3-axis linear accelerometer and 3-axis magnetometer combined
into a single package. The device features a selectable I2C or
point-to-point SPI serial interface with 14-bit accelerometer and 16-bit
magnetometer ADC resolution along with smart-embedded functions.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
[added commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
If device recipe has specified DEVICE_DTS variable, the dtb is built
anyway by OpenWrt buildroot image rules. Drop the patch and adjust the
location of compiled dtb.
Cc: Scott Roberts <ttocsr@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tar has ability to change current dir, so use that instead additional
command invocation. Also being here, change tar arguments to make final
archive reproducible.
Cc: Scott Roberts <ttocsr@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This device receipe selects bunch of packages which some are re-defined,
unnecessary or irrelevant. Clean them up, so only basic functionality
persist.
Cc: Scott Roberts <ttocsr@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Don't rewrite global DTS_DIR, instead, use proper variable for
specifying devices dts directory. For consistency, also specify the
variable in default profile, as suggested by Adrian Schmutzler.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The AVM FRITZ!WLAN Repeater 450E's WPS button is not active low.
Correct the active low flag to avoid unintenional activation of
failsafe mode on boot.
Signed-off-by: David Bauer <mail@david-bauer.net>
Fixes the following warning for ARM targets:
WARNING: "return_address" [vmlinux] is a static EXPORT_SYMBOL_GPL
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The previous workaround for the unsupported mkimage xz compression
leads to the TP-Link TL-WDR4900s simpleImage bootwrapper being gzip
compressed, which does not fit the kernel partition.
Removing the uImage gerneration works around this problem.
Signed-off-by: David Bauer <mail@david-bauer.net>
This hunk became obsolete the moment when our
gpio-button-hotplug learned how to deal with
interrupt-supported gpio buttons. The gpio driver
never supported interrupt handling, so these
properties never served any use (outside of a
enhanced ppc4xx-gpio driver that was dropped).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This removes the assignment of setup and cleanup functions for the ath79
target. Assigning the setup-method will lead to 'setup_transfer' not
being assigned in spi_bitbang_init.
Also drop the redundant cleanup assignment, as this also happens in
spi_bitbang_init.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes some outstanding issues with the Kernel 5.4 build:
* Adds missing support patch for the Enterasys WS-AP3710i
* Fixes incorrect NAND symbols
* Adds patch for broken image wrapping
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds important NAND config symbols.
These are necessary as otherwise the devices
won't find the rootfs on the NAND chips.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch just refreshes the 5.4 patches. It seems as if
070-v4.20-soc-qcom-spm-add-SCM-probe-dependency.patch is
already applied, so drop it. It also does a quick
make kernel_oldconfig to get rid of unneeded symbols.
[Looks like USB and Ethernet need some more work].
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds a few more symbols that I found that
need disabling in order to not break the automatic build.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This backports commits from master that fix AES ciphers when using the
qce driver:
- A couple of simple fixes for CTR and XTS modes used with AES:
* 041-crypto-qce-fix-ctr-aes-qce-block-chunk-sizes.patch
* 042-crypto-qce-fix-xts-aes-qce-key-sizes.patch
- A fix for a bug that affected cases when there were more entries in
the input sg list than necessary to actually encrypt, resulting in
failure in gcm, where the authentication tag is present after the
encryption data:
* 043-crypto-qce-save-a-sg-table-slot-for-result-buf.patch
- A fix to update the IV buffer passed to the driver from the kernel:
* 044-crypto-qce-update-the-skcipher-IV.patch
- A patch that reduces memory footprint and driver initialization by
only initializing the fallback mechanism where it is actually used:
* 046-crypto-qce-initialize-fallback-only-for-AES.patch
- Three patches that make gcm and xts modes work with the qce driver,
and improve performance with small blocks:
* 047-crypto-qce-use-cryptlen-when-adding-extra-sgl.patch
* 048-crypto-qce-use-AES-fallback-for-small-requests.patch
* 049-crypto-qce-handle-AES-XTS-cases-that-qce-fails.patch
- A patch that allows the hashes/ciphers to be built individually.
* 051-crypto-qce-allow-building-only-hashes-ciphers.patch
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[renumbered patches, added patches from dropped commit, refreshed, 5.4]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds the neon based implementations of AES & SHA256.
For AES, according to the kernel config help:
Use a faster and more secure NEON based implementation of AES in CBC,
CTR and XTS modes.
Bit sliced AES gives around 45% speedup on Cortex-A15 for CTR mode
and for XTS mode encryption, CBC and XTS mode decryption speedup is
around 25%. (CBC encryption speed is not affected by this driver.)
This implementation does not rely on any lookup tables so it is
believed to be invulnerable to cache timing attacks.
...
The observed speedups on ipq40xx are more modest: speedup is around 20%
for CTR mode and for XTS mode encryption, CBC and XTS mode decryption
speedup is around 10%. Measurements were made using tcrypt, with
1024-bytes blocks for CTR & CBC, and 4096-bytes for XTS.
The aes-neon-bs driver uses a fallback for CBC encryption; that fallback
could be either the generic driver written in C, or the scalar arm-asm
one. Even though aes-arm is 1.9% slower, it is more resilient to timing
attacks (the reason for being slower), so it is being included here.
The neon sha256 module increases performance over the generic module by
33%.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[Enable only ciphers for now, reorder patch in series to help bisect
as new symbols could lead to build failures, 5.4]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This backports a commit updating the API of the QCE crypto engine to
what is used in current kerenl, easing future upstream backports.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[renumber patches, refreshed, added 5.4 patches]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch disables the CRYPTO KERNEL SYMBOLs that are touched
by the upcoming ipq40xx patch "ipq40xx: use neon crypto drivers"
from "Eneas U de Queiroz" and more so for his follow up patches
for the other ARM targets in this series. This should help to
prevent at least a few potential build errors on other archs.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SOC: IPQ4019 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
FLASH: NOR 4 MiB + NAND 128 MiB
ETH: Qualcomm Atheros QCA8072
WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11a/n/ac 2:2x2
WLAN2: Qualcomm Atheros QCA9888 5GHz 802.11a/n/ac 2:2x2
INPUT: WPS Button
LEDS: Power, LAN1, LAN2, WLAN 2.4GHz, WLAN 5GHz-1, WLAN 5GHz-2, OPMODE
1. Load Ramdisk via U-Boot
To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
* 115200bps
* 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports.
c. Set a static ip 192.168.99.8 for Ethernet that connects to board.
d. The PC must have a TFTP server launched and listening on the interface to which the board is connected.
e. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.
U-BOOT> set serverip 192.168.99.9 && tftpboot 0x84000000 192.168.99.8:openwrt.itb && bootm
Signed-off-by: Steven Lin <steven.lin@senao.com>
[copied 4.19 dts to 5.4]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Fix typedef clash on darwin.
HOSTCC scripts/mod/file2alias.o
scripts/mod/file2alias.c:47:3: error: typedef redefinition with different types ('struct uuid_t' vs '__darwin_uuid_t' (aka 'unsigned char [16]'))
} uuid_t;
^
/Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX.sdk/usr/include/sys/_types/_uuid_t.h:31:25: note: previous definition is here
typedef __darwin_uuid_t uuid_t;
^
scripts/mod/file2alias.c:1305:42: error: array initializer must be an initializer list or string literal
DEF_FIELD(symval, tee_client_device_id, uuid);
^
2 errors generated.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This is still missing a lot of love but people want to start working on it
so lets give them a common baseline.
Signed-off-by: John Crispin <john@phrozen.org>
* Fix some bugs in the driver
* Add missing clock and reset references in dts
* Rename mdio-bus to mdio so the driver find it
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
[refreshed]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* Sync the patches with the changes done for kernel 4.19
* Use KERNEL_TESTING_PATCHVER
* Refresh the configuration
* Fix multiple compile bugs in the patches
* Only add own ag71xx files for kernel 4.19 and use upstream version for
5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The nvmem framework is now used in net/ethernet/eth.c and the nvmem
sysfs is split into a separate Kconfig option. More work would be needed
to adapt this patch for the broader use. The current patch compiles fine
on ath79, but it breaks the x86 target.
nvmem is also compiled into the kernel for most of our targets for
example ath79 anyway, so patching the kernel to remove it is now harder
and not the case on multiple targets anyway. Instead of making this work
on kernel 5.4 just remove this hack patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This makes it possible to select CONFIG_CRYPTO_LIB_ARC4 directly. We
need this to be able to compile this into the kernel and make use of it
from mac80211 backports.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The configuration was refreshed and KERNEL_TESTING_PATCHVER was set to
make it easy to compile for kernel 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The following patches were removed because they are integrated in the upstream kernel 5.4:
* backport-5.4/047-v4.21-mtd-keep-original-flags-for-every-struct-mtd_info.patch
* backport-5.4/048-v4.21-mtd-improve-calculating-partition-boundaries-when-ch.patch
* backport-5.4/080-v5.1-0001-bcma-keep-a-direct-pointer-to-the-struct-device.patch
* backport-5.4/080-v5.1-0002-bcma-use-dev_-printing-functions.patch
* backport-5.4/095-Allow-class-e-address-assignment-via-ifconfig-ioctl.patch
* backport-5.4/101-arm-cns3xxx-use-actual-size-reads-for-PCIe.patch
* backport-5.4/200-v5.2-usb-dwc2-Set-lpm-mode-parameters-depend-on-HW-configuration.patch
* backport-5.4/210-arm64-sve-Disentangle-uapi-asm-ptrace.h-from-uapi-as.patch
* backport-5.4/380-v5.3-net-sched-Introduce-act_ctinfo-action.patch
* backport-5.4/450-v5.0-mtd-spinand-winbond-Add-support-for-W25N01GV.patch
* backport-5.4/451-v5.0-mtd-spinand-Add-initial-support-for-Toshiba-TC58CVG2.patch
* backport-5.4/452-v5.0-mtd-spinand-add-support-for-GigaDevice-GD5FxGQ4xA.patch
* backport-5.4/455-v5.1-mtd-spinand-Add-support-for-all-Toshiba-Memory-produ.patch
* backport-5.4/456-v5.1-mtd-spinand-Add-support-for-GigaDevice-GD5F1GQ4UExxG.patch
* backport-5.4/460-v5.0-mtd-spi-nor-Add-support-for-mx25u12835f.patch
* backport-5.4/460-v5.3-mtd-spinand-Define-macros-for-page-read-ops-with-thr.patch
* backport-5.4/461-v5.3-mtd-spinand-Add-support-for-two-byte-device-IDs.patch
* backport-5.4/462-v5.3-mtd-spinand-Add-support-for-GigaDevice-GD5F1GQ4UFxxG.patch
* backport-5.4/463-v5.3-mtd-spinand-Add-initial-support-for-Paragon-PN26G0xA.patch
* backport-5.4/700-v5.1-net-phylink-only-call-mac_config-during-resolve-when.patch
* backport-5.4/701-v5.2-net-phylink-ensure-inband-AN-works-correctly.patch
* backport-5.4/702-v4.20-net-ethernet-Add-helper-for-MACs-which-support-asym-.patch
* backport-5.4/703-v4.20-net-ethernet-Add-helper-for-set_pauseparam-for-Asym-.patch
* backport-5.4/704-v4.20-net-phy-Stop-with-excessive-soft-reset.patch
* backport-5.4/705-v5.1-net-phy-provide-full-set-of-accessor-functions-to-MM.patch
* backport-5.4/706-v5.1-net-phy-add-register-modifying-helpers-returning-1-o.patch
* backport-5.4/707-v5.1-net-phy-add-genphy_c45_check_and_restart_aneg.patch
* backport-5.4/708-v5.3-net-phylink-remove-netdev-from-phylink-mii-ioctl-emu.patch
* backport-5.4/709-v5.3-net-phylink-support-for-link-gpio-interrupt.patch
* backport-5.4/710-v5.3-net-phy-allow-Clause-45-access-via-mii-ioctl.patch
* backport-5.4/711-v5.3-net-sfp-add-mandatory-attach-detach-methods-for-sfp-.patch
* backport-5.4/712-v5.3-net-sfp-remove-sfp-bus-use-of-netdevs.patch
* backport-5.4/713-v5.2-net-phylink-avoid-reducing-support-mask.patch
* backport-5.4/714-v5.3-net-sfp-Stop-SFP-polling-and-interrupt-handling-duri.patch
* backport-5.4/715-v5.3-net-phylink-don-t-start-and-stop-SGMII-PHYs-in-SFP-m.patch
* backport-5.4/740-v5.5-net-phy-avoid-matching-all-ones-clause-45-PHY-IDs.patch
* backport-5.4/741-v5.5-net-phylink-fix-link-mode-modification-in-PHY-mode.patch
* pending-5.4/103-MIPS-perf-ath79-Fix-perfcount-IRQ-assignment.patch
* pending-5.4/131-spi-use-gpio_set_value_cansleep-for-setting-chipsele.patch
* pending-5.4/132-spi-spi-gpio-fix-crash-when-num-chipselects-is-0.patch
* pending-5.4/220-optimize_inlining.patch
* pending-5.4/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch
* pending-5.4/475-mtd-spi-nor-Add-Winbond-w25q128jv-support.patch
* pending-5.4/477-mtd-add-spi-nor-add-mx25u3235f.patch
* pending-5.4/479-mtd-spi-nor-add-eon-en25qh64.patch
Some bigger changes were done to this feature and we did not port this patch yet:
* hack-5.4/207-disable-modorder.patch
This depends on BOOTMEM which was removed from the kernel, this needs some bigger changes:
* hack-5.4/930-crashlog.patch
A different version of the FPU disable patch was merged upstream, OpenWrt needs some adaptations.
* pending-5.4/304-mips_disable_fpu.patch
- no crashlog support yet as a required file got deleted upstream
- Removed patch below, which is now seen as a recursive dependency [1]
- Removed patch below due to build error [2]
- fix still required to avoid identical function def [3]
- Fixes included from Blocktrron
- Fixes included from Chunkeey
- Fix included from nbd regarding "dst leak in Flow Offload"
[1] target/linux/generic/hack-5.4/260-crypto_test_dependencies.patch
[2] target/linux/generic/hack-5.4/207-disable-modorder.patch
[3] target/linux/generic/pending-5.4/613-netfilter_optional_tcp_window_check.patch
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No changes were done to the patches while coping them. Currently they do
not apply on top of kernel 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In accordance to ebc090e420 ("ath79: reduce spi-max-frequency to 50 MHz")
this also reduces the spi-max-frequency to 50 MHz for the last remaining
device with higher frequency in ath79. This will save us from having a
single special case that will require adjustment when the spi driver for
this device is changed in the future.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Chuanhong Guo <gch981213@gmail.com>
This applies some minor DTS style improvements to the files kept
in OpenWrt at the moment:
- harmonize/improve LED/pinmux node names
- harmonize empty lines between nodes
- change "ok" to "okay"
- some other minor formatting adjustments
Since changes are only cosmetical, they are only applied to the
"newer" DTS files for kernel 4.19.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move DTS files newly created by patch files to files directory. This will make
these files much more maintainable.
Patching the kernel Makefile is unnecessary, as the DTS files specified in
DEVICE_DTS will be compiled by OpenWrt buildroot anyway.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The introduction of ebf0d8dade ("ath79: add new ar934x spi driver")
made the SPI memory unusable on devices with very high spi-max-frequency
(104 MHz).
Here's how the actual clock is calculated: (AHB_CLK/((CLOCK_DIVIDER+1)*2))
where AHB_CLK is a fixed clock (e.g. 200MHz on AR9331) and CLOCK_DIVIDER
is the parameter we can set. Highest clock according to this formula is
AHB_CLK/2 (100MHz, but that didn't work in device tests).
The next possible value is AHB_CLK/4 (50MHz). Speeds between 50 MHz and
100 MHz will be rounded down, so using values higher than 50 MHz does
not provide any benefit.
Consequently, this patch reduces spi-max-frequency for all devices with
values higher than 50 MHz to 50 MHz (effectively, this only affects
devices with 104 MHz before this patch).
Tested on GL.inet GL-AR150:
Boot fails with 104 MHz but is successful with both 50 MHz and 80 MHz
(fast-read), where the latter two yield identical read speeds.
Fixes: ebf0d8dade ("ath79: add new ar934x spi driver")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The introduction of ebf0d8dade (ath79: add new ar934x spi driver)
made the SPI memory unusable. Reducing the spi-max-frequency to
a smaller value makes it work again.
Tested on two MikroTik RouterBOARD wAP G-5HacT2HnD devices.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch ports support for the MikroTik RouterBOARD 922UAGS-5HPacD
with a built-in 802.11ac High-Power radio (31dBm), which was already
available in the ar71xx target.
See https://mikrotik.com/product/RB922UAGS-5HPacD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9558 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9882 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE-in 24V
- SFP: 1x host
- USB: 1x 2.0 type A
- PCIe: 1x Mini slot (also contains USB 2.0 for 3G/LTE modems)
- SIM slot: 1x mini-SIM
Working:
- Board/system detection
- SPI and NAND storage
- PCIe
- USB type A host
- Wireless
- Ethernet
- LEDs (user, phy0)
- Reset button
- Sysupgrade to/from ar71xx
Not supported:
- RSSI LEDs
- SFP cage
Installation methods:
- Sysupgrade from ar71xx (it is advisable to use the -n option to
wipe any previous settings), or
- Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
The calgary IOMMU was only used on high-end IBM systems in the early
x86_64 age. This is an unlikely OpenWrt target and in fact upstream
are looking to drop the driver entirely with the bonus that we no
longer see:
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
When porting support from ar71xx to ath79, the reset-gpios option was
missed. Due to a hardware bug, this would eventually leave the devices
with RX-deaf Ethernet PHY.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Commit 9a1f441ac8 ("kirkwood: enable SoC drivers in the kernel config")
enabled I2C_MV64XXX in the kernel config, and the subsequent commit 0d5ba94088
("orion: enable SoC drivers in the kernel config") removed kmod-i2c-mv64xxx
package entirely. As the feature is now kernel built-in and the package does not
exist anymore, we can safely remove kmod-i2c-mv64xxx from DEVICE_PACKAGES.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
