Commit Graph

850 Commits

Author SHA1 Message Date
Adrian Schmutzler
91b1a625f4 ath79: add label MAC address for TP-Link RE450 v2/v3
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-31 15:44:05 +02:00
Andreas Wiese
c764c512ac ath79: add support for TP-Link RE450 v3
TP-Link RE450 v3 is a dual band router/range-extender based on
Qualcomm/Atheros QCA9563 + QCA9880.

This device is nearly identical to RE450 v2 besides a modified flash
layout (hence I think force-flashing a RE450v2 image will lead to at
least loss of MAC address).

Specification:

- 775 MHz CPU
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 1x 10/100/1000 Mbps Ethernet (AR8033 PHY)
- 7x LED, 4x button-
- possible UART header on PCB¹

Flash instruction:
Apply factory image in OEM firmware web-gui.

¹ Didn't check to connect as I didn't even manage to connect on
  RE450v2 (AFAIU it requires disconnecting some resistors, which I was
  too much of a coward to do).  But given the similarities to v2 I
  think it's the same or very similar procedure (and most likely also
  the only way to debrick).

Signed-off-by: Andreas Wiese <aw-openwrt@meterriblecrew.net>
[remove dts-v1 and compatible in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-31 15:44:05 +02:00
Lech Perczak
7e513136c6 ath79: add support for TP-Link TL-WR802N V1 and V2
Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of Flash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)

Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to web interface:
  [V1] http://192.168.0.1
  [V2] http://192.168.0.254
  Default user is "admin" & password is "admin".
  On V2, there is no DHCP server running by default, so remember to set
  IP manually.
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware:
  [V1] "*.factory.bin"
  [V2] "*.factory-us.bin" or  "*.factory-eu.bin" for eu model
  Web interface may complain if filename is too long. In such case,
  rename .bin to something shorter.
- Click upgrade

Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
      Serial Configuration 115200 8n1

- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
    (IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
    (e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
    (e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
    (e.g bootm 0x9f020000)

Notes:

When porting from ar71xx target to ath79, I found out that on V2,
reset button is on GPIO12 and active low, instead of GPIO11 and
active high. By cross-flashing V1 firmware to V2, I confirmed
the same is true for V1.
Also according to manual of V1, this one also has green
LED instead of blue - both of those issues were fixed accordingly.

The MAC address assignment has been checked with OEM firmware.

Installation manual based on ar71xx support by Thomas Roberts

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit message, add MAC address comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-31 15:44:05 +02:00
Roger Pueyo Centelles
95caa3436d ath79: update WA/XC devices UBNT_VERSION to 8.5.3
Ubiquiti WA devices with newer hw version 2011K require UBNT_VERSION
to be at least 8.5.3, otherwise the image is rejected:

   New ver: WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3
   Versions: New(525568) 8.5.0, Required(525571) 8.5.3
   Invalid version 'WA.ar934x.v8.5.0-42.OpenWrt-r10947-65030d81f3'

For consistency, also increase version number for XC devices.

Tested-by: Pedro <pedrowrt@cas.cat>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-05-31 15:44:05 +02:00
Adrian Schmutzler
705fe43522 ath79: fix LEDs for GL.inet GL-AR150
Since the wireless LED was used for boot and set up with a DT
trigger, the WiFi indication hasn't worked on ath79 at all.

In addition, a look into the manual revealed that the OEM
configuration is as follows:

LED 1 (green): power
LED 2 (green): configurable
LED 3 (red): wireless

So, let's just keep the WiFi trigger and convert the rest to its
"intended" use.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-31 15:44:05 +02:00
Thibaut VARÈNE
f10da7cb4d packages/boot: remove rbcfg
The new sysfs soft_config driver makes buggy rbcfg obsolete and
entirely replaces it.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-28 11:09:10 +02:00
Pavel Balan
ad84c09502 ath79: add support for COMFAST CF-E130N v2
This patch adds support for the COMFAST CF-E130N v2, an outdoor wireless
CPE with a single Ethernet port and a 802.11bgn radio.

Specifications:

 - QCA9531 SoC
 - 1x 10/100 Mbps Ethernet with PoE-in support
 - 64 MB of RAM (DDR2)
 - 16 MB of FLASH
 - 5 dBi built-in antenna
 - POWER/LAN/WLAN green LEDs
 - 4x RSSI LEDs (2x red, 2x green)
 - UART (115200 8N1) and GPIO (J9) headers on PCB

Flashing instructions:

 The original firmware is based on OpenWrt so a sysupgrade image can be
 installed via the stock web GUI.

 The U-boot bootloader also contains a backup TFTP client to upload the
 firmware from. Upon boot, it checks its ethernet network for the IP
 192.168.1.10. Host a TFTP server and provide the image to be flashed as
 file firmware_auto.bin.

MAC address setup:

The art partition contains four consecutive MAC addresses:

0x0    aa:bb:cc:xx:xx:c4
0x6    aa:bb:cc:xx:xx:c6
0x1002 aa:bb:cc:xx:xx:c5
0x5006 aa:bb:cc:xx:xx:c7

However, the manufacturer in its infinite wisdom decided that one address
is enough and both eth0 and WiFi get the MAC address from 0x0 (yes, that's
overwriting the existing and valid address in 0x1002). This is obviously
also the address on the device's label.

Signed-off-by: Pavel Balan <admin@kryma.net>
[fix configs partition, fix IMAGE_SIZE, add MAC address comment, rename
ATH_SOC to SOC]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-28 01:47:54 +02:00
Adrian Schmutzler
2b92ee36ae ath79: replace tab after DT label by space
The common separator in this case is a single space.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-28 00:48:39 +02:00
Sebastian Schaper
64d088d8f9 ath79: increase spi clock for D-Link DIR-842
AHB is 258 MHz for this device (CPU_PLL / 3), but there is no difference
between 64 MHz and 50 MHz for spi-max-frequency, thus increase to 50 MHz.

Tested on revisions C1 and C3.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2020-05-26 22:49:18 +02:00
Sebastian Schaper
8643c0b53d ath79: define switch reset-gpios for D-Link DIR-842
GPIO 11 needs to be pulled high for the external gigabit switch to work,
this is currently solved via gpio-hog. Replace with phy0 reset-gpios.

Tested on revisions C1 and C3. Reset button is still working for reboot,
to enter failsafe, and to enter bootloader http recovery.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2020-05-26 22:49:18 +02:00
Sebastian Schaper
6ce1e299be ath79: fix LEDs for D-Link DIR-842
The device has a total of 8 LEDs, 5 of which are controlled by the switch
(LAN 1-4, WAN). Only power, wifi and wps are controlled by the SoC.

 * led_power is on GPIO 5 (not 15), boot flashing sequence is now visible
 * remove led 'internet', since it is only connected to the switch
 * remove ucidef_set_led_switch for WAN from 01_leds, as it has no effect

Tested on revisions C1 and C3.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-26 22:49:18 +02:00
Roger Pueyo Centelles
8383e63808 ath79/mikrotik: add missing kernel config symbol for 5.4
The UBIFS_FS_ZSTD is exposed when UBIFS is enabled.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-26 11:46:46 +02:00
Adrian Schmutzler
4661b05390 kernel: properly insert local mtd partition parsers
Between 4.19 and 5.4, the kernel moved the partition parsers into
the parsers subdirectory. This led to some necessary rebasing of
our local patches for parsers, which partially has been performed
without caring about where the code was inserted.

This commit tries to adjust our local patches so that parsers are
inserted at the "proper" positions with respect to alphabetic sorting
(if possible). Thus, the commit is cosmetic.

While this might look useless now, it will make life easier when
adding other parsers in the future or for rebasing on kernel changes.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-25 21:11:47 +02:00
Stijn Segers
9a1f4b2f83 ath79/nand: add support for Netgear WNDR4300SW
This patch adds support for the WNDR4300SW, marketed by California ISP
SureWest (hence the 'SW' suffix). Hardware wise, it's identical to the
WNDR4300 v1.

Specifications:
* SoC: Atheros AR9344
* RAM: 128 MB
* Flash: 128 MB NAND flash
* WiFi: Atheros AR9580 (5 GHz) and AR9344 (2,4 GHz)
* Ethernet: 5x 1000Base-T
* LED: Power, WAN, LAN, WiFi, USB, WPS
* UART: on board, to the right of the RF shield at the top of the board

Installation:

* Flashing through the OEM web interface:
  + Connect your computer to the router with an ethernet cable and browse
    to http://192.168.1.1/
  + Log in with the default credentials are admin:password
  + Browse to Advanced > Administration > Firmware Upgrade in the Netgear
    interface
  + Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img
  + Proceed with the firmware installation and give the device a few
    minutes to finish and reboot.

* Flashing through TFTP:
  + Configure your wired client with a static IP in the 192.168.1.x range,
    e.g. 192.168.1.10 and netmask 255.255.255.0.
  + Power off the router.
  + Press and hold the RESET button (the factory reset button on the bottom
    of the device, with the red circle around it) and turn the router on
    while keeping the button pressed.
  + The power LED will start flashing orange. You can release the button
    once it switches to flashing green.
  + Transfer the image over TFTP:
    $ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2020-05-24 14:44:00 +02:00
David Bauer
ebddc5f984 ath79: add support for Enterasys WS-AP3705i
Hardware
--------
SoC:    Atheros AR9344
RAM:    128M DDR2
FLASH:  2x Macronix MX25L12845EM
        2x 16MiB SPI-NOR
WLAN2:  Atheros AR9344 2x2 2T2R
WLAN5:  Atheros AR9580 2x2 2T2R
SERIAL: Cisco-RJ45 on the back (115200 8n1)

Installation
------------

The U-Boot CLI is password protected (using the same credentials as the
OS). Default is admin/new2day.

1. Download the OpenWrt initramfs-image. Place it into a TFTP server
   root directory and rename it to 1401A8C0.img. Configure the TFTP
   server to listen at 192.168.1.66/24.

2. Connect the TFTP server to the access point.

3. Connect to the serial console of the access point. Attach power and
   interrupt the boot procedure when prompted (bootdelay is 1 second).

4. Configure the U-Boot environment for booting OpenWrt from Ram and
   flash:

   $ setenv boot_openwrt 'setenv bootargs; bootm 0xbf230000'
   $ setenv ramboot_openwrt 'setenv serverip 192.168.1.66;
     tftpboot 0x85000000; bootm'
   $ setenv bootcmd 'run boot_openwrt'
   $ saveenv

5. Load OpenWrt into memory:

   $ run ramboot_openwrt

   Wait for the image to boot.

6. Transfer the OpenWrt sysupgrade image to the device. Write the image
   to flash using sysupgrade:

   $ sysupgrade -n /path/to/openwrt-sysuograde.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-05-22 21:54:30 +02:00
Hauke Mehrtens
586661018e ath79: Do not build buffalo_whr-g301n by default
The squashfs partition is getting too big.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-05-21 22:16:17 +02:00
Adrian Schmutzler
4a61a88f90 ath79: add support for TP-Link TL-WA901ND v4 and v5
This ports support for the TL-WA901ND v4 and v5 from ar71xx to ath79.
They are similar to the TP9343-based TL-WR940N v3/v4 and TL-WR941ND v6.

Specifications:
  SoC: TP9343
  Flash/RAM: 4/32 MiB
  CPU: 750 MHz
  WiFi: 2.4 GHz b/g/n
  Ethernet: 1 port (100M)

Flashing instructions:
  Upload the factory image via the vendor firmware upgrade option.

Flash instruction (TFTP):
  1. Set PC to fixed ip address 192.168.0.66
  2. Download *-factory.bin image and rename it to * (see below)
  3. Start a tftp server with the image file in its root directory
  4. Turn off the router
  5. Press and hold Reset button
  6. Turn on router with the reset button pressed and wait ~15 seconds
  7. Release the reset button and after a short time
     the firmware should be transferred from the tftp server
  8. Wait ~30 second to complete recovery.

  * The image name for TFTP recovery is wa901ndv4_tp_recovery.bin for
  both variants.

In ar71xx, a MAC address with offset 1 was used for ethernet port.
That's probably wrong, but this commit sticks to it until we know
the correct value.

Like in ar71xx, this builds the default factory.bin with EU country
code.

Thanks to Leonardo Weiss for testing on the v5.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 13:35:38 +02:00
Roger Pueyo Centelles
a0ef42e77c ath79: add support for Ubiquiti PowerBeam 5AC 500
The Ubiquiti PowerBeam 5AC 500 (PBE-5AC-500) is an outdoor 802.11ac
5 GHz bridge with a radio feed and a dish antenna.

Specifications:
 - SoC: Qualcomm Atheros QCA9558
 - RAM: 128 MB DDR2
 - Flash: 16 MB SPI NOR (mx25l12805d)
 - Ethernet: 1x 10/100/1000 Mbps Atheros 8031, 24 Vdc PoE-in
 - WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff
 - Buttons: 1x (reset)
 - LEDs: 1x power, 1x Ethernet, 4x RSSI, all blue
 - UART: not tested

Not supported:
 - RSSI LEDs (probably through 74HC595 chip)

Installation from stock airOS firmware:
 - Follow instructions for XC-type Ubiquiti devices on OpenWrt wiki at
   https://openwrt.org/toh/ubiquiti/common

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-05-17 21:03:30 +02:00
Aleksander Jan Bajkowski
2f7118712e ath79: increase spi frequency on tp-link tl-wr1043nd v2
Increase SPI frequency to 33.333 MHz. It's maximum frequency supported
by SPI Flash memory chip without Fast read opcode.

Before:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real	0m 3.21s
user	0m 0.00s
sys	0m 3.21s

After:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real	0m 2.52s
user	0m 0.00s
sys	0m 2.52s

Tested on TP-Link TL-WR1043ND V2.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-05-15 10:00:32 +08:00
Koen Vandeputte
eb17ee294c kernel: bump 5.4 to 5.4.41
Refreshed all patches.

Compile-tested on: imx6
Runtime-tested on: imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-14 13:33:40 +02:00
Koen Vandeputte
7dd2d7289a kernel: bump 4.19 to 4.19.122
Refreshed all patches.

Remove upstreamed:
- 551-loop-Better-discard-support-for-block-devices.patch

Fixed:
- CVE-2020-11884
- CVE-2020-12114
- CVE-2019-3016
- CVE-2020-11669

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-12 12:36:28 +02:00
Lech Perczak
94f3449977 ath79: dts: add missing 'serial0' alias for TP-Link TL-MR3040v2
Out of all devices currently supported based on AR9331 chipset,
this one had the 'serial0' alias missing. Add it to fix setting of
/dev/console and login shell on the onboard UART.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2020-05-08 19:39:36 +02:00
Thibaut VARÈNE
9242d691ec ath79/mikrotik: load caldata via sysfs loader
This commit takes advantages of base-files 220 which introduces routines
to perform caldata loading directly via the kernel sysfs loader helper.
This has the benefits of not wasting flash space to store caldata.

Memory footprint is reduced to the bare minimum: for devices that don't
need MAC patching, the caldata is loaded directly, for devices that do
need MAC patching, the caldata is extracted to /tmp, patched and then
loaded.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
1e24af5638 ath79/mikrotik: use standard caldata functions
With the implementation of a sysfs interface to access WLAN data, this
target no longer needs a special wrapper to extract caldata.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
301bc3290d ath79/mikrotik: don't use mtd-mac-address in DTS
As evidenced here[1] the device MAC address can be stored at a random
offset in the hard_config partition. Rely on sysfs to update the MAC
address correctly.

To match sticker and vendor OS behavior, WAN MAC is set to the device
base MAC and LAN MAC is incremented from that.

Note: this will trigger a harmless kernel message during boot:
ag71xx 19000000.eth: invalid MAC address, using random address

There is no clean workaround to prevent this message from being emitted.

[1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
65d5053045 ath79/mikrotik: enable mikrotik platform driver
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
8f90dbfd1f ath79/mikrotik: use routerbootpart partitions
Enable routerbootpart partitions on MikroTik devices.

Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
c8b2ad4185 ath79/mikrotik: enable CONFIG_MTD_ROUTERBOOT_PARTS
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Daniel Golle
aa0526b5f2 ath79: fix dts of Teltonika RUT9xx devices
The previous commits were missing a semicolon.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-29 22:59:23 +01:00
Daniel Golle
aa4a33ac62 ath79: add support for Teltonika RUT955 H7V3C0
This board was previously supported in ar71xx as 'RUT9XX'. The
difference between that and the other RUT955 board already supported in
ath79 is that instead of the SPI shift registers driving the LEDs and
digital outputs that model got an I2C GPIO expander instead.

To support LEDs during early boot and interrupt-driven digital inputs,
I2C support as well as support for PCA953x has to be built-in and
cannot be kernel modules, hence select those symbols for ath79/generic.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by PCA9539)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector

Serial console (/dev/ttyS0) pinout:

- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side

Flash instruction:

Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.1".

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-29 21:32:35 +01:00
Daniel Golle
c8b309b53d ath79: split Teltonika RUT955 to support other RUT9xx models
Split device-tree of Teltonika RUT955 into a generic RUT9xx part and
a part specific to that version of RUT955 already supported.
Also harmonize GPIO and LED names with what is used by the vendor
firmware and assign RS485 DTR signal.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-29 21:32:35 +01:00
Adrian Schmutzler
522f6b7eee ath79: add SUPPORTED_DEVICES based on ar71xx for some devices
This adds some still-missing board names for old TP-Link devices
to ath79 SUPPORTED_DEVICES.

Fixes: FS#3017

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-28 20:28:06 +02:00
Álvaro Fernández Rojas
2e5e9b459e ath10k-ct-firmware: rename ct-htt packages
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-04-28 09:33:09 +02:00
Adrian Schmutzler
80a094aaf3 ath79: indicate boot/failsafe/upgrade for NanoBeam/Nanostation AC
Like for Ubiquiti PowerBeam 5AC Gen2, the highest RSSI LED can
be exploited to indicate boot/failsafe/upgrade for the NanoBeam AC
and Nanostation AC as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 23:28:51 +02:00
Roger Pueyo Centelles
e210fe91b1 ath79: add support for Ubiquiti PowerBeam 5AC Gen2
The Ubiquiti PowerBeam 5AC Gen 2 (PBE-5AC-Gen2) is an outdoor 802.11ac
5 GHz bridge with a radio feed and a dish antenna. The device is
hardware-compatible with the LiteBeam AC Gen2, plus the 4 extra LEDs.

Specifications:
 - SoC: Qualcomm Atheros AR9342 rev 2
 - RAM: 64 MB DDR2
 - Flash: 16 MB SPI NOR (mx25l12805d)
 - Ethernet: 1x 10/100/1000 Mbps Atheros 8035, 24 Vdc PoE-in
 - WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff
 - WiFi 2.4 GHz: Atheros AR9340 (SoC-based)
 - Buttons: 1x (reset)
 - LEDs: 1x power, 1x Ethernet, 4x RSSI via GPIO. All blue.
 - UART: not tested

Installation from stock airOS firmware:
 - Follow instructions for WA-type Ubiquiti devices on OpenWrt wiki

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[changed device name in commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 23:17:30 +02:00
David Bauer
654eec5a2d ath79: enable SGMII workaround for affected boards
These boards suffer from a sudden inability to establish a link on the
SGMII. Enable the workaround to fix the link when it dies.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:22:02 +02:00
David Bauer
c760469918 ath79: ag71xx: unify version dependent code
Use IS_ERR_OR_NULL macro to use the same code on kernel 4.19 as well as
5.4.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:21:45 +02:00
David Bauer
5358d8b995 ath79: ag71xx: remove code for legacy kernels
ath79 does not support kernels prior to 4.19 anymore.
Remove legacy code for those kernels from the ag71xx driver.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:20:41 +02:00
David Bauer
3f5997fb28 ath79: remove unused TP-Link partition parser
This parser was added with the target, but no device seems to use it
currently, as all partitions are specified in the device-tree.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:20:41 +02:00
David Bauer
1f45ed6c99 ath79: fix QCA953x DDR and GPIO compatible bindings
The memory as well as GPIO controller had the wrong SoC name used for
their compatible binding.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:03:18 +02:00
David Bauer
fceef288cf ath79: correct QCA9550 machine compatible binding
Some boards using a QCA9556 or QCA9558 had their machine compatible
binding incorrectly set to qca,qca9557.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:03:00 +02:00
David Bauer
c0a80b7125 ath79: rename qca9557.dtsi to qca955x.dtsi
There are at least 3 different chips in the Scorpion series of SoCs.
Rename the common DTSI to better reflect it's purpose for the whole
series.

Also rename the compatible bindings from qca,ar9557 and qca,qca9557
to qca,qca9550.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:02:29 +02:00
Adrian Schmutzler
d3c9630811 ath79: move tplinkpart.c parser to patches
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Like for myloader.c in the previous patch,
this patch moves tplinkpart.c to the kernel patches, so the
code and the kernel includes are at the same location and
the path can be adjusted per kernel.

While at it, remove some outdated kernel version switches from
the C code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-24 17:50:59 +02:00
Adrian Schmutzler
5f92349841 kernel: fix include of myloader.o since kernel 5.4
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Based on this, the selection of myloader.o in OpenWrt
was also moved to that subdirectory, while the Kconfig and our local
myloader.c file remained in /drivers/mtd.

This resulted in linking errors like the following (on ath25@5.4):

make[8]: *** No rule to make target 'drivers/mtd/parsers/myloader.o', ...
   needed by 'drivers/mtd/parsers/built-in.a'.  Stop.
make[7]: *** [scripts/Makefile.build:500: drivers/mtd/parsers] Error 2
make[6]: *** [scripts/Makefile.build:500: drivers/mtd] Error 2

Since myloader.c is not too big, this patch moves it to the kernel patches,
allowing to adjust the path for kernel 5.4 and keeping Makefiles and
file paths better in sync.

Other patches have been refreshed accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-24 17:50:12 +02:00
David Bauer
8d9c1087e4 ath79: add support for AVM FRITZ!WLAN Repeater 450E
SOC:    Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM:    64MB Zentel A3R12E40CBF DDR2
FLASH:  16MiB Winbond W25Q128 SPI NOR
WLAN1:  QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT:  WPS button
LED:    Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
        Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes.
You need to powercycle the device afterwards to boot OpenWRT.

Tested-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-19 16:45:40 +02:00
David Bauer
edf812e25c ath79: remove stray pipe
Fixes: 8918c038f3 ("ath79: add support for AVM FRITZ!WLAN Repeater 1750E")

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-17 14:15:09 +02:00
David Bauer
8918c038f3 ath79: add support for AVM FRITZ!WLAN Repeater 1750E
This commit adds support for the AVM Fritz!WLAN Repeater 1750E

SOC:	Qualcomm QCA9556 (Scorpion) 720MHz MIPS74Kc
RAM:    64MB Zentel A3R12E40CBF DDR2
FLASH:  16MiB Winbond W25Q128 SPI NOR
WLAN1:  QCA9556 2.4 GHz 802.11b/g/n 3x3
WLAN2:  QCA9880 5 GHz 802.11 n/ac 3x3
INPUT:  WPS button
LED:    Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
        Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi (correct MAC)
 - 5 GHz WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-17 13:27:40 +02:00
David Bauer
d883eaacd4 ath79: add QCA9550 reset sequence
The QCA9550 family of SoCs have a slightly different reset
sequence compared to older chips.

Normally the bootloader performs this sequence, however
some bootloader implementation expect the operating system
to clear the reset. Also get the PCIe resets from OF to
support the second RC of the QCA9558.

This is required for the AVM FRITZ!WLAN Repeater 1750E to work,
as EVA leaves the PCIe bus in reset.

Tested: AVM FRITZ!WLAN Repeater 1750E - OCEDO Koala

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-17 13:23:06 +02:00
Roger Pueyo Centelles
c0430b8da4 ath79: reduce spi-max-frequency for Mikrotik wAP G-5HacT2HnD
The previous spi-max-frequency value did not work with all the CPU speed
settings (configurable with rbcfg or from the stock firmware); the new
one does for the three of them.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-04-16 13:44:18 +02:00
Koen Vandeputte
20efd5614a ath79: MikroTik: fix missing nand on kernel 5.4
Following symbol got renamed upstream:
CONFIG_MTD_NAND --> CONFIG_MTD_RAW_NAND

Also add this renamed symbol so NAND also works on kernel 5.4.

After:
[    0.628372] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[    0.634862] nand: Samsung NAND 128MiB 3,3V 8-bit
[    0.639554] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.647263] Scanning device for bad blocks
[    0.656228] random: fast init done
[    0.789652] 3 fixed-partitions partitions found on MTD device ar934x-nand
[    0.796550] Creating 3 MTD partitions on "ar934x-nand":
[    0.801874] 0x000000000000-0x000000040000 : "booter"
[    0.807715] 0x000000040000-0x000000400000 : "kernel"
[    0.813551] 0x000000400000-0x000008000000 : "ubi"

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-16 13:23:11 +02:00