Do not include the dnsmasq and odhcpd-ipv6only package by default any
more. These services are not needed on a switch. If someone needs this
it is still possible to use opkg or image builder to add them.
This decreases the compressed image size by about 165KBytes.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 2acebbdcaa)
removes usb-port remains as neither the WAC510 nor the WAC505
come with a USB port. Update the LED properties to phase out
labels and introduce generic node-names as well as adding
the color, function and function-enumerator properties.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 026fda10a5)
This commit replaces patch number 0703 with the upstream accepted
version. This patch requires backporting an additional patch to
avoid conflicts.
The only significant change is the lower maximum MTU. Packets with
lengths over 2400 may be dropped.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
(cherry picked from commit b4970dab6b)
This commit builds on previous efforts to add support
for Sophos devices.
* Add support for Sophos XG 85 with/without wireless
* Add support for Sophos XG 86 with/without wireless
Tested on Sophos XG 85w rev1 and XG 86 rev 1
Signed-off-by: Raylynn Knight <rayknight@me.com>
(cherry picked from commit c7bcbcd492)
In commit ab143647ef ("kernel: generic: improve FIT partition parser")
part_bits was bumped to 2 in order to allow up to 3 additional FIT
sub-images mapped into sub-partitions.
This change has to be reflected also in our local patch
420-mtd-set-rootfs-to-be-root-dev.patch
which still assumed part_bits==1 for mtdblock devices in case of
CONFIG_FIT_PARTITION=y.
Fixes: #9557
Fixes: ab143647ef ("kernel: generic: improve FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 13960fb0e0)
* only map filesystems configured in 'loadables'
* allow mapping more than one filesystem (e.g. customization/branding
or localization in addition to rootfs)
* small cleaning here and there
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit ab143647ef)
If the selected boot configuration is stored by U-Boot in '/chosen'
node as 'bootconf' attribute, use that configuration to resolve the
block device used as rootfs. Fall back to use the default configuration
in case 'bootconf' is not present.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 503f3b9f0e)
at91/sama7 fails to build due to:
| Asymmetric (public-key cryptographic) key type (ASYMMETRIC_KEY_TYPE) [Y/?] y
| Asymmetric public-key crypto algorithm subtype (ASYMMETRIC_PUBLIC_KEY_SUBTYPE) [Y/?] y
| Asymmetric TPM backed private key subtype (ASYMMETRIC_TPM_KEY_SUBTYPE) [N/m/?] (NEW)
|Error in reading or end of file.
please note that asym_tpm (module) has been removed in 5.17:
<https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=d3cff4a9>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 6387715093)
Modified the radio frequency hardware part of e2600ac c1/c2,
need to cooperate with the modified board.bin file, the device
can work normally.
Signed-off-by: 张 鹏 <sd20@qxwlan.com>
(cherry picked from commit bdc786e82c)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tel(co Electronics) X1 Pro is preventing ipq40xx generic
from building due to the KERNEL_SIZE.
Whenever bigger kernels are possible, if lzma is supported
is unknown.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 4ce52de450)
The OCEDO Raccoon had significant packet-loss with cables longer than 50
meter. Disabling EEE restores normal operation.
Also change the ethernet config to reduce loss on sub-1G links.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4551bfd91f)
Required to allow sysupgrades from OpenWrt 19.07.
Closes#7071
Fixes: 98fbf2edc0 ("ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloader")
Tested-by: J. Burfeind <git@aiyionpri.me>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 8ba71f1f6f)
While it hasn't always been clear whether the "AP" is part of the model
name on the Ubiquiti website, we include it for all other pre-AC
variants (AP Pro and the AP Outdoor+). Add it to the original UniFi AP
as well for consistency.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit dc23df8a8c)
The label has the MAC address of eth0, not the WLAN PHY address.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 2a02b70499)
uDPU provides a FIT based initramfs, but currently gets stuck after U-boot
starts the kernel at "Starting kernel..".
It is due to the load address being too low, so increase it in order to get
the initramfs booting again.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 80f21e5336)
uDPU has 2 LM75 compatible temperature sensors, so include the driver for
them by default in order to utilize them.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit a8b2d35903)
Remove "a" character from the first line of patch
738-v5.14-01-net-dsa-qca8k-fix-an-endian-bug-in-qca8k-get-ethtool.patch
Otherwise `git am` fails to apply this patch which is annoying when
trying to do some development / rebasing.
Signed-off-by: Marek Behún <kabel@kernel.org>
(cherry picked from commit f811c33b19)
a20-olinuxino-lime2 is currently having hard time with link detection of
certain 1000Mbit partners due to usage of generic PHY driver, probably
due to following missing workaround introduced in upstream in commit
3aed3e2a143c ("net: phy: micrel: add Asym Pause workaround"):
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
As a20-olinuxino-lime2 has Micrel KSZ9031RNXCC-TR Gigabit PHY since
revision H, so we need to use Micrel PHY driver on those devices.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit ffa1088f63)
As the upcoming release will be based on Linux 5.10 only, remove all
kernel configuration as well as patches for Linux 5.4.
There were no targets still actively using Linux 5.4.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 3a14580411)
Also known as the "Xiaomi Router AX3200" in western markets,
but only the AX6S is widely installation-capable at this time.
SoC: MediaTek MT7622B
RAM: DDR3 256 MiB (ESMT M15T2G16128A)
Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG)
WLAN: 2.4/5 GHz 4T4R
2.4 GHz: MediaTek MT7622B
5 GHz: MediaTek MT7915E
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531B
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8
Power: 12 VDC, 1.5 A
Notes:
U-Boot passes through the ethaddr from uboot-env partition,
but also has been known to reset it to a generic mac address
hardcoded in the bootloader.
However, bdata is also populated with the ethernet mac addresses,
but is also typically never written to. Thus this is used instead.
Installation:
1. Flash stock Xiaomi "closed beta" image labelled
'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'.
(MD5: 5eedf1632ac97bb5a6bb072c08603ed7)
2. Calculate telnet password from serial number and login
3. Execute commands to prepare device
nvram set ssh_en=1
nvram set uart_en=1
nvram set boot_wait=on
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
4. Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://<IP>:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Stock Xiaomi recovery tftp that accepts their signed images,
with default ips of 192.168.31.1 + 192.168.31.100.
Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img)
Triggered by holding reset pin on powerup.
A simple implementation of this would be via dnsmasq's
dhcp-boot option or using the vendor's (Windows only)
recovery tool available on their website.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
(cherry picked from commit 9f9477b275)
Some units of the Xiaomi Redmi Router AX6S/Xiaomi Router AX3200 contain this part.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
(cherry picked from commit 4177de10df)
Telco X1 Pro is a Cat12 LTE-A Pro modem router.
Vendor firmware is based on a recent version of OpenWrt.
Flashing is possible via CLI using sysupgrade -F -n
The serial headers allow bootloader and console access
Serial setting: 115200 8N1
Brief Specifications:
IPQ4019 SoC
32MB flash
512MB RAM
4x gigabit LAN
1x gigabit WAN
Dual-band Wave-2 wifi
2x SMA LTE antenna connectors
2x RP-SMA wifi antennas
1x USB 2.0 port
1x Reset button
Serial headers installed
1x Nano SIM tray
1x Quectel EM-12G LTE-A Pro modem
1x M.2 slot attached to USB 3.0
1x internal micro SD card slot
Signed-off-by: Nicholas Smith <nicholas@nbembedded.com>
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G
The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed
Installation:
Update to the last D-Link firmware through web-ui before OpenWRT
installation then follow the instructions to patch your device using
D-Link FailsafeUI.
- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.1 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.
Signed-off-by: Igor Nazarov <tigron.dev@gmail.com>
Some vendors like Seeedstudio in their product [1] with Raspberry Pi
Compute Module 4 uses Microchip LAN7800 (USB 3.0 to Gigabit
Ethernet Bridge) - USB 3.0 extended from PCIe of CM4.
lsusb output:
```
Bus 002 Device 002: ID 0424:7800 Microchip LAN7800
```
Raspberry Pi 4 and even Compute Module 4 has many resources available
and for just one kernel module it is not necessary to add additional specific CM4 profiles.
Let's include it by default, so the both Ethernet ports will be usable
to have better user-experience. Because previous generation of Raspberry
Pi included LAN7800 Gigabit Ethernet by default and it is enabled there
[2] in kernel without additional kernel module, which was added recently [3].
After this commit in dmesg can be found this:
```
root@OpenWrt:~# dmesg | grep lan
[ 7.038889] lan78xx 2-3:1.0 (unnamed net_device) (uninitialized): int urb period 64
[ 7.090484] usbcore: registered new interface driver lan78xx
```
Tested and works with sysupgrade image.
[1] https://www.seeedstudio.com/Dual-GbE-Carrier-Board-with-4GB-RAM-32GB-eMMC-RPi-CM4-Case-p-5029.html
[2] 32c74552b2/target/linux/bcm27xx/bcm2709/config-5.4 (L437)
[3] 31647d8be8
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Kernel 5.6 introduced a new config symbol SERIAL_8250_16550A_VARIANTS.
In kernel 5.8, this symbol was changed to default to on on !x86, as some
embedded devices still use 16650A variants. Let's play safe here and
enable this symbol in the generic config, to avoid others from running
into this problem and having to spend several hours trying to bisect
this problem. While we could disable the symbol in the x86 target
configs, a 20ms boot time reduction really isn't worth the time wasted
on bisecting this issue.
Matt discovered this problem while working on adding support for the
WatchGuard Firebox M200 to the qoriq target, where it caused some
characters to be missing on the console output.
Reported-by: Matt Fawcett <mattytap@icloud.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
- fix eth0 eth1 sharing same mac so it conforms to the behavior stated
in the original commit and the way it is in vendor firmware :
WAN is label, LAN is label +1 and WLAN is label +2
- add default leds config
- add default network config
Signed-off-by: Pascal Coudurier <coudu@wanadoo.fr>
Buildbot has reported following issue while crunching mpc85xx/p1010
subtarget:
Extreme Networks WS-AP3825i (WS_AP3825I) [N/y/?] (NEW)
Fix it by disabling that config symbol in target kernel config and while
at it fix DTS whitespace issue.
Fixes: 7e614820a8 ("mpc85xx: add support for Extreme Networks WS-AP3825i")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Without a partition subnode ofpart_core still parses direct subnodes as
partitions, but it ignores nodes with a compatible property. Due to
this, the switch to nvmem-cells made the urlader partition inaccessible.
As a result, the wireless network was broken, as the calibration data
is read from that partition by a script.
Fixes: #8983
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The &spi node has #address-cells = <1> and #size-cells = <0>. Drop the
extra 0 in the reg property from the SPI flash node to ensure it's
number of cells matches the definition in the parent node. This also
makes the reg property for the SPI flash node consistent with all other
VR9 boards.
Fixes: eae6cac6a3 ("lantiq: add support for AVM FRITZ!Box 7362 SL")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Timo Schroeder reported:
"The TP-Link Archer VR2600v is stuck in a boot loop on written
snapshot image. It's able to boot using the snapshot uimage
though, but there ath10k firmware can't be found.
21.02.2 release version doesn't have either problem."
The VR2600v has a 512 byte header at the beginning of the
firmware that needs to be accounted for.
Fixes: f6a01d7f5c ("ipq806x: convert TP-Link Archer VR2600v to denx,uimage")
Reported-by: Timo Schroeder <der.timosch@gmail.com>
References: <https://github.com/openwrt/openwrt/issues/9467>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware:
- SoC: Freescale P1020
- CPU: 2x e500v2 @ 800MHz
- Flash: 64MiB NOR (1x Intel JS28F512)
- Memory: 256MiB (2x ProMOS DDR3 V73CAG01168RBJ-I9H 1Gb)
- WiFi1: 2.4+5GHz abgn 3x3 (Atheros AR9590)
- Wifi2: 5GHz an+ac 3x3 (Qualcomm Atheros QCA9890)
- ETH: 2x PoE Gigabit Ethernet (2x Atheros AR8035)
- Power: 12V (center-positive barrel) or 48V PoE (active or passive)
- Serial: Cisco-compatible RJ45 next to 12V power socket (115200 baud)
- LED Driver: TI LV164A
- LEDs: (not functioning)
- 2x Power (Green + Orange)
- 4x ETH (ETH1 + ETH2) x (Green + Orange)
- 2x WiFi (WiFi2 + WiFi1)
Installation:
1. Grab the OpenWrt initramfs <openwrt-initramfs-bin>, e.g.
openwrt-mpc85xx-p1020-extreme-networks_ws-ap3825i-initramfs-kernel.bin.
Place it in the root directory of a DHCP+TFTP server, e.g. OpenWrt
`dnsmasq` with configuration `dhcp.server.enable_tftp='1'`.
2. Connect to the serial port and boot the AP with options
e.g. 115200,N,8. Stop autoboot in U-Boot by pressing Enter after
'Scanning JFFS2 FS:' begins, then waiting for the prompt to be
interrupted. Credentials are identical to the one in the APs
interface. By default it is admin / new2day: if these do not work,
follow the OEM's reset procedure using the reset button.
3. Set the bootcmd so the AP can boot OpenWrt by executing:
```uboot
setenv boot_openwrt "cp.b 0xEC000000 0x2000000 0x2000000; interrupts off; bootm start 0x2000000; bootm loados; fdt resize; fdt boardsetup; fdt chosen; bootm prep; bootm go;"
setenv bootcmd "run boot_openwrt"
saveenv
```
If you plan on going back to the vendor firmware - the bootcmd for it
is stored in the boot_flash variable.
4. Load the initramfs image to RAM and boot by executing
```uboot
setenv ipaddr <ipv4 client address>;
setenv serverip <tftp server address>;
tftpboot 0x2000000 <openwrt-initramfs-bin>;
interrupts off;
bootm start 0x2000000;
bootm loados;
fdt resize;
fdt boardsetup;
fdt chosen;
bootm prep;
bootm go;
```
5. Make a backup of the "firmware" partition if you ever wish to go back
to the vendor firmware.
6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
folder.
7. Flash OpenWrt using sysupgrade.
```ash
sysupgrade /tmp/<openwrt-sysupgrade-bin>
```
Notes:
- We must step through the `bootm` process manually to avoid fdt
relocation. To explain: the stock U-boot (and stock Linux) are configured
with a very large CONFIG_SYS_BOOTMAPSZ (and the device's stock Linux
kernel is configured to be able to handle it). The U-boot version
predates the check for the `fdt_high` variable, meaning that upon fdt
relocation, the fdt can (and will) be moved to a very high address; the
default appears to be 0x9ffa000. This address is so high that when the
Linux kernel starts reading the fdt at the beginning of the boot process,
it encounters a memory access exception and panics[5]. While it is
possible to reduce the highest address the fdt will be relocated to by
setting `bootm_size`, this also has the side effect of limiting the
amount of RAM the kernel can use[3].
- Because it is not relocated, the flattened device tree needs to be
padded in the build process to guarantee that `fdt resize` has
enough space.
- The primary ethernet MAC address is stored (and set) in U-boot; they are
shimmed into the device tree by 'fdt boardsetup' through the
'local-mac-address' property of the respective ethernet node, so OpenWrt
does not need to set this at runtime. Note that U-boot indexes the
ethernet nodes by alias, which is why the device tree explicitly aliases
ethernet1 to enet2.
- LEDs do not function under OpenWrt. Each of 8 LEDs is connected to an
output of a TI LV164A shift register, which is wired to GPIO lines and
operates through bit-banged SPI. Unfortunately, I am unable to get the
spi-gpio driver to recognize the `led_spi` device tree node at all, as
confirmed by patching in printk messages demonstrating
spi-gpio.c::spi_gpio_probe never runs. It is possible to manually
articulate the shift register by exporting the GPIO lines and stepping
their values through the sysfs.
- Though they do not function under OpenWrt, I have left the pinout details
of the LEDs and shift register in the device tree to represent real
hardware.
- An archive of the u-boot and Linux source for the AP3825i (which is one
device of a range of devices code-named 'CHANTRY') be found here[1].
- The device has an identical case to both the Enterasys WS-AP3725i and
Adtran BSAP-2030[2] (and potentially other Adtran BSAPs). Given that
there is no FCC ID for the board itself (only its WLAN modules), it's
likely these are generic boards, and even that the WS-AP3725i is
identical, with only a change in WLAN card. I have ordered one to confirm
this.
- For additional information: the process of porting the board is
documented in an OpenWrt forum thread[4].
[1]: magnet:?xt=urn:btih:f5306a5dfd06d42319e4554565429f84dde96bbc
[2]: https://forum.openwrt.org/t/support-for-adtran-bluesocket-bsap-2030/48538
[3]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/29
[4]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168
[5]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/26
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This device seems to be same hardware as a WN3000RPv3
Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
(see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
(preferred method).
Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
powercycling the device
Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1
Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This reverts commit 7bc20cb614.
It adds support for Netgear WN3100RPv2, but the commit title is wrong.
It will be re-added with the correct title.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This device seems to be same hardware as a WN3000RPv3
Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
(see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
(preferred method).
Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
powercycling the device
Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1
Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The DWR-961 A1 Wireless Router is based on the MT7620A SoC.
It's a merge of two Amit boards: DWR-960 with ethernet part
of Lava LR-25G001.
ROMID it's taken from Telenor branded version and it works with tested
device. Images from D-Link site for this router are from DWR-953 and it
have ROMID DLK6E2424001. I don't know if it's mistake on web-site
or if it's will require different image.
Specification:
- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612 mpcie card)
- 5x 10/100/1000 Mbps Ethernet: 4xLAN and 1xWAN (QCA8337)
- 2x internal, non-detachable antennas (Wifi 2.4G)
- 3x external, detachable antennas (2x LTE, 1x Wifi 5G)
- 1x LTE modem cat 6
- UART (J5) header on PCB (57600 8n1)
- 13x LED, 2x button
- JBOOT bootloader
Installation:
Apply factory image via http web-gui or JBOOT recovery page
How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The I2C controller used in QorIQ PPC devices requires the mpc-i2c
driver, which is enabled by the I2C_MPC kernel config symbol. Enable
this and its dependencies in the target kernel config, as is done for
the mpc85xx target.
This fixes missing hwmon, rtc and tpm devices on the M300.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Seeing failure to build because of missing symbols related to provisioning
CONFIG_KEXEC and signed images. Without this, if you set
CONFIG_KERNEL_KEXEC=y and try to build, target/linux will hang at:
scripts/kconfig/conf --syncconfig Kconfig
...
kexec system call (KEXEC) [Y/n/?] y
kexec file based system call (KEXEC_FILE) [Y/n/?] y
Verify kernel signature during kexec_file_load() syscall (KEXEC_SIG) [N/y/?] (NEW)
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Backport patches
381a730182f1 ("net: dsa: Move VLAN filtering syncing out of dsa_switch_bridge_leave")
108dc8741c20 ("net: dsa: Avoid cross-chip syncing of VLAN filtering")
from upstream (currently in net-next) to fix null-pointer dereference.
Signed-off-by: Marek Behún <kabel@kernel.org>
FCC ID: 2AG6R-AN700APIAC
Araknis AN-700-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1750
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3
- QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:xb art 0x0
phy1 2.4G *:xc ---
phy0 5GHz *:xd ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: 2AG6R-AN500APIAC
Araknis AN-500-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1200
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9557 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- QCA9882 WLAN PCI card 168c:003c, 5 GHz, 2x2, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:e1 art 0x0
phy1 2.4G *:e2 ---
phy0 5GHz *:e3 ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: U2M-AN300APIN
Araknis AN-300-AP-I-N is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EWS310AP
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- AR9382 WLAN PCI on-board 168c:0030, 5 GHz, 2x2
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM 1839ZFG V59C1512164QFJ25
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:7d art 0x0
phy1 2.4G *:7e ---
phy0 5GHz *:7f ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
