This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router.
Device specification
--------------------
SoC Type: MediaTek MT7621AT (880 MHz, 2 cores)
RAM (Nanya NT5CC64M16GP): 128 MiB
Flash (Macronix MX30LF1G18AC): 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615N): a/n/ac, 4x4
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
USB ports: 1xUSB3.0
Buttons: 2 button (reset, wps)
LEDs: Red, Green, Blue
Zigbee (EFR32MG1B232GG): 3.0
Stock bootloader: U-Boot 1.1.3
Power: 12 VDC, 1.5 A
Installation (fw 2.0.9)
-----------------------
1. Login to the web interface under SuperUser (root) credentials.
Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the
device written on the backplate stick.
2. Navigate to Setting -> WAN. Add:
Name - WAN1
Connection Type - Static
IP Address - 172.16.0.1
Netmask - 255.255.255.0
Save -> Apply. Set default: WAN1
3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add:
Protocol - SSH
Port - 22
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN Interface - WAN1
Save ->Apply
Add:
Protocol - HTTP
Port - 80
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN interface - WAN1
Save -> Apply
4. Set up your PC ethernet:
Connection Type - Static
IP Address - 172.16.0.2
Netmask - 255.255.255.0
Gateway - 172.16.0.1
5. Connect PC using ethernet cable to the WAN port of the router
6. Connect to the router using SSH shell under SuperUser account
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface under admin account
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 171.16.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses (fw 2.0.9)
------------------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:e8 |
| WAN | label + 1 | *:e9 |
| 2g | label + 4 | *:ec |
| 5g | label + 5 | *:ed |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
Factory image format
--------------------
+---+-------------------+-------------+--------------------+
| # | Offset | Size | Description |
+---+-------------------+-------------+--------------------+
| 1 | 0x0 | 0x200 | Tag Header Factory |
| 2 | 0x200 | 0x100 | Tag Header Kernel1 |
| 3 | 0x300 | 0x100 | Tag Header Kernel2 |
| 4 | 0x400 | SIZE_KERNEL | Kernel |
| 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) |
+---+-------------------+-------------+--------------------+
Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
The armvirt target has been renamed to armsr (Arm SystemReady),
so the GRUB configuration also needs to change.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Contains following updates:
* ipq8074: update RegDB in new submitted BDF
* Revert "ipq8074: update RegDB in new submitted BDF"
* qcn9074: update RegDB in new submitted BDF
* ipq8074: update RegDB in new submitted BDF
* qca-wireless: ipq40xx: add BDFs for ZTE MF287+
* Add BDFs for prpl Foundation Haze board
Signed-off-by: Petr Štetiar <ynezz@true.cz>
There is no need for SSDK to support 5.15 anymore since the only user and
possible future ones are on 6.1.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit add u-boot env config for GL-MT3000, so
that we can use fw_printenv to print u-boot env and
use fw_setenv to set u-boot env in GL-MT3000.
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
CVE-2023-2650 fix
Remove upstreamed patches
Major changes between OpenSSL 3.0.8 and OpenSSL 3.0.9 [30 May 2023]
* Mitigate for very slow OBJ_obj2txt() performance with gigantic OBJECT IDENTIFIER sub-identities. (CVE-2023-2650)
* Fixed buffer overread in AES-XTS decryption on ARM 64 bit platforms (CVE-2023-1255)
* Fixed documentation of X509_VERIFY_PARAM_add0_policy() (CVE-2023-0466)
* Fixed handling of invalid certificate policies in leaf certificates (CVE-2023-0465)
* Limited the number of nodes created in a policy tree (CVE-2023-0464)
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
One is never to write to dev->addr directly. In 6.1 it will be a const and
with the newly enabled WERROR, we get a failing grade.
Lets fix this ahead of time.
Ref: adeef3e321
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Update bootloader environment for BPi-R3 and BPi-R64 to adapt to new
device tree overlay mechanism now that support for multiple device
tree overlays has been added.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 5d2de00555.
I received multiple reports that in various configurations this FW version
is not stable and crashes, so lets revert to 01385 revision which works.
Fixes#12815
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [fixes tag]
Currently kernel crashes when of_phy_connect has issues:
Unable to handle kernel access to user memory outside uaccess routines at virtual address 0000000000000308
...
pc : phy_attached_print+0x28/0x1b0
lr : phy_attached_info+0x14/0x20
...
Call trace:
phy_attached_print+0x28/0x1b0
phy_attached_info+0x14/0x20
nss_dp_adjust_link+0x544/0x6c4 [qca_nss_dp]
of_phy_connect returns either pointer or NULL, so can't be checked with
IS_ERR macro.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
b09b316aeaf6 blobmsg: add blobmsg_parse_attr function
eac92a4d5d82 blobmsg: add blobmsg_parse_array_attr
ef5e8e38bd38 usock: fix poll return code check
6fc29d1c4292 jshn.sh: Add pretty-printing to json_dump
5893cf78da40 blobmsg: Don't do at run-time what can be done at compile-time
362951a2d96e uloop: fix uloop_run_timeout
75a3b870cace uloop: add support for integrating with a different event loop
Signed-off-by: Felix Fietkau <nbd@nbd.name>
412d03012f13 network: prevent adding endpoint routes for addresses on the network
faaf9cee6ef4 utils: fix ipv4 checksum issue
0e1c2fad3540 pex-msg: fix memory leak on fread fail in pex_msg_update_request_init
51be0ed659d0 host: fix crash parsing gateway when no endpoint is specified
ca17601dc24e wg-linux: add support for splitting netlink messages for allowed ips
7d3986b7a5a2 wg-linux: increase default messages size
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Synchronize the ath11k backports with the current ath-next tree.
This introduces support for MBSSID and EMA, adds factory test mode and
some new HTT stats.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport EMA beacon support from kernel 6.4.
It is required for MBSSID/EMA suport in ath11k that will follow.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
QCA released a point update for the 2.9.0.1 firmware, so lets update to it.
Runtime tested on Dynalink DL-WRX36.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Built-in engine configs are added in libopenssl-conf/install stage
already, postinst/add_engine_config is just duplicating them, and
due to the lack of `config` header it results a broken uci config:
> uci: Parse error (invalid command) at line 3, byte 0
```
config engine 'devcrypto'
option enabled '1'
engine 'devcrypto'
option enabled '1'
option builtin '1'
```
Add `builtin` option in libopenssl-conf/install stage and remove
duplicate engine configuration in postinst/add_engine_config to
fix this issue.
Fixes: 0b70d55a64 ("openssl: make UCI config aware of built-in engines")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Release Notes:
https://valgrind.org/docs/manual/dist.news.html
This improves support for the memory allocator used in musl libc 1.2.2
and later which is currently used by OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Build and package kernel self-tests used for BPF testing, program and JIT
development. This package, together with the existing 'kmod-bpf-test', was
extensively used for past upstream Linux JIT submissions [1].
Currently this includes only 'test_verifier'; building 'test_progs' will
fail due to known endian limitations with bpftool skeletons.
[1]:https://lore.kernel.org/bpf/cover.1633392335.git.Tony.Ambardar@gmail.com
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Set net.core.bpf_jit_kallsyms=1 in /etc/sysctl.d/10-default.conf.
For privileged users, this exports addresses of JIT-compiled programs to
appear in /proc/kallsyms when present, allowing their use for debugging
and in traces.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The Amazon ENA network devices are also used on the
AWS Arm (Graviton) instance types, so move it from
the x86-only module file to the top level netdevices.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The MDIO bus multiplexing framework is used by some drivers
such as dwmac-sun8i.
As this is a per-driver requirement, set it to be hidden in the menu.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This adds a separate package for EFI on Arm SystemReady
compatible machines. 32-bit Arm UEFI is supported as well.
It is very similar to x86-64 EFI setup, without the
need for BIOS backward compatibility and slightly
different default modules.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
When using the Gemini, we apply patches that create a single
module that support both host and device mode these days.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(move module to gemini target, keep both 6.1+2-ish + 5.15 module
CONFIG and files around until 5.15 is dropped)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add support for the Xunlong Orange Pi R1 Plus LTS.
Manually generated of-platdata files to avoid swig dependency.
Tested-by: Volkan Yetik <no3iverson@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Add support for the Xunlong Orange Pi R1 Plus.
Manually generated of-platdata files to avoid swig dependency.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The smsc95xx driver got selftest support with kernel 5.18, add the new
dependency fixing the all kernel modules build on MIPS malta with kernel
6.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_PHYLINK Kconfig option in the kernel selects CONFIG_LIBPHY.
Add this dependency to fix the all kernel modules build on MIPS malta
and armvirt with kernel 6.1.
With kernel 5.15 mod-phylink and kmod-sfp are empty packages because
no OpenWrt kmod is selecting a module which needs sfp or phylink
support.
Fixes: #12758
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Contains following changes:
* bridge: bridge_dump_info: add dumping of bridge attributes
* bridge: make it more clear why the config was applied
* cmake: fix build by reordering the cflags definitions
* treewide: fix multiple compiler warnings
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It's required by bcm53xx. This allows dropping separated oseama package
and avoids some code duplication.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Some of firmware utils may be required on target devices. It's useful
e.g. for dealing with some firmware formats. That is often required
(supporting specific format) to provide an option to revert to original
firmware.
So far we had packaged "otrx" util only for use on Broadcom targets.
Refactor that to package the whole firmware-utils project so we can
package any single util needed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
At this moment loadaddr in most layerscape boards are configured to
0x81000000. 5.15 kernel on some boards is bigger than 5.10 and it cause error:
Loading kernel from FIT Image at 81000000 ...
Using 'config-1' configuration
Trying 'kernel-1' kernel subimage
Description: ARM64 OpenWrt Linux-5.15.112
Created: 2023-05-21 17:39:35 UTC
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x810000ec
Data Size: 7513944 Bytes = 7.2 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x80000000
Entry Point: 0x80000000
Hash algo: crc32
Hash value: 6fd69550
Hash algo: sha1
Hash value: ee34c753ffb615e199a428762824ad4a0aaef90a
Verifying Hash Integrity ... crc32+ sha1+ OK
Loading fdt from FIT Image at 81000000 ...
Using 'config-1' configuration
Trying 'fdt-1' fdt subimage
Description: ARM64 OpenWrt fsl_ls1088a-rdb-sdboot device tree blob
Created: 2023-05-21 17:39:35 UTC
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x8172a98c
Data Size: 19794 Bytes = 19.3 KiB
Architecture: AArch64
Hash algo: crc32
Hash value: 59792ba3
Hash algo: sha1
Hash value: 135585a49f86cd85acea559b78b0098ae99d5e12
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x8172a98c
Uncompressing Kernel Image
ERROR: new format image overwritten - must RESET the board to recover
resetting ...
This patch changes loadaddr to 0x88000000 (like LS1012A-FRDM board) to
avoid overlapping for bigger images (like initramfs) too.
Tested-by: Alexandra Alth <alexandra@alth.de> [LS1088ARDB]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
