Commit Graph

22617 Commits

Author SHA1 Message Date
Petr Štetiar
5562c5add2 ipq40xx: fix DAP-2610 boot failure
Albert has reported, that his DAP-2610 wont boot with the latest
snapshot and Fredrik has found out, that the device gets stuck at
"Waiting for root device ..." due to missing 5.4 kernel config symbol
CONFIG_MTD_SPLIT_WRGG_FW which was probably lost during the kernel
version bump.

Ref: https://forum.openwrt.org/t/dap-2610-bricked-help-needed
Fixes: 272e0a702a ("ipq40xx: add v5.4 support")
Suggested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-31 16:20:47 +02:00
李国
533b130adc x86/64: add cdrom and iso9660 drivers
The iso image need cdrom and iso9660 drivers to boot, otherwise it will
hang when mounting the root file system

Signed-off-by: 李国 <uxgood.org@gmail.com>
2020-03-31 16:20:47 +02:00
李国
a6b7c3e672 x86: generate EFI platform bootable images
Add EFI platform bootable images for x86 platforms. These images can
also boot from legacy BIOS platform.

EFI System Partition need to be fat12/fat16/fat32 (not need to load
filesystem drivers), so the first partition of EFI images are not ext4
filesystem any more.

GPT partition table has an alternate partition table, we did not
generate it. This may cause problems when use these images as qemu disk
(kernel can not find rootfs), we pad enough sectors will be ok.

Signed-off-by: 李国 <uxgood.org@gmail.com>
[part_magic_* refactoring, removed genisoimage checks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-31 16:20:47 +02:00
李国
d9228514cc grub2: make some change to add efi platform support
1.generate boot image at Package/install section
2.move boot image to $(STAGING_DIR_IMAGE)/grub2/
3.add efi variant to support efi platform

Signed-off-by: 李国 <uxgood.org@gmail.com>
2020-03-31 16:20:47 +02:00
Álvaro Fernández Rojas
49109cedab bcm27xx: update 5.4 patches from RPi foundation
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-03-31 13:18:08 +02:00
Yousong Zhou
437eb41f23 generic: mips: exclude more dsemul code when fpu-emu is not enabled
The patch is backported from mips-next.  In addition to minor reduction
of code size and runtime memory use, the more apparent difference is
that the delay slot emulation page will not be present for those targets
with fpu emulation disabled (CONFIG_MIPS_FP_SUPPORT=n)

Memory maps of busybox before and after this change

  root@OpenWrt:/# cat /proc/self/maps
  00400000-00449000 r-xp 00000000 00:02 23         /bin/busybox
  00458000-00459000 r-xp 00048000 00:02 23         /bin/busybox
  00459000-0045a000 rwxp 00049000 00:02 23         /bin/busybox
  77dc0000-77de2000 r-xp 00000000 00:02 273        /lib/libgcc_s.so.1
  77de2000-77de3000 r-xp 00012000 00:02 273        /lib/libgcc_s.so.1
  77de3000-77de4000 rwxp 00013000 00:02 273        /lib/libgcc_s.so.1
  77de4000-77e7b000 r-xp 00000000 00:02 271        /lib/libc.so
  77e8a000-77e8c000 rwxp 00096000 00:02 271        /lib/libc.so
  77e8c000-77e8e000 rwxp 00000000 00:00 0
  7fd86000-7fda7000 rw-p 00000000 00:00 0          [stack]
  7fefd000-7fefe000 r-xp 00000000 00:00 0
  7ffe6000-7ffe7000 r--p 00000000 00:00 0          [vvar]
  7ffe7000-7ffe8000 r-xp 00000000 00:00 0          [vdso]

  root@OpenWrt:/# cat /proc/self/maps
  00400000-00449000 r-xp 00000000 00:02 23         /bin/busybox
  00458000-00459000 r-xp 00048000 00:02 23         /bin/busybox
  00459000-0045a000 rwxp 00049000 00:02 23         /bin/busybox
  77d55000-77d77000 r-xp 00000000 00:02 274        /lib/libgcc_s.so.1
  77d77000-77d78000 r-xp 00012000 00:02 274        /lib/libgcc_s.so.1
  77d78000-77d79000 rwxp 00013000 00:02 274        /lib/libgcc_s.so.1
  77d79000-77e10000 r-xp 00000000 00:02 272        /lib/libc.so
  77e1f000-77e21000 rwxp 00096000 00:02 272        /lib/libc.so
  77e21000-77e23000 rwxp 00000000 00:00 0
  7fe23000-7fe44000 rw-p 00000000 00:00 0          [stack]
  7ff63000-7ff64000 r--p 00000000 00:00 0          [vvar]
  7ff64000-7ff65000 r-xp 00000000 00:00 0          [vdso]

Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2020-03-30 11:28:11 +08:00
Kevin Darbyshire-Bryant
af35205626 kernel: Enable CMOS RTC support on 5.4
Enable kernel symbol CONFIG_RTC_DRV_CMOS which was enabled in 4.14 &
4.19

Fixes FS#2905 and now my APU2 picks up time from RTC

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-03-29 21:41:43 +01:00
Hauke Mehrtens
f46a3c7b14 ramips: Deactivate NETGEAR WNCE2001 by default
The root file system is getting too big for this device and this breaks
the ramips/rt305x build.

Do not build images for this board by default to fix this problem.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-03-29 22:36:05 +02:00
Daniel Engberg
3a761c90af treewide: Don't diverge from upstream default HZ settings on 4.19
Most targets upstream use 250Hz or even 1000Hz by default while
100Hz is hardcoded in OpenWrt's default config. Use upstream default
except for apm821xx which hardsets 1000Hz instead of platform default of
250Hz.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[Apply same changes to 5.4]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-03-29 17:27:54 +01:00
Michal Cieslakiewicz
e2b89ea069 kernel: generic: 5.4: fix mtd concat panic on read/write functions
Commit 2431c4f5b46c32c4ac495456b1ef4ce59c0bb85d ("mtd: Implement
mtd_{read,write}() as wrappers around mtd_{read,write}_oob()") for kernel 5.4
restrict mtd devices to register only one type of read/write functions
(either generic or OOB).

mtd concat does not follow above rule and defines both methods at the same
time, causing this type of device to be rejected by kernel. For routers that
use mtd concat for root UBI volume that means kernel panic and boot loop with
following error:

[    0.767307] Creating 1 MTD partitions on "ubi-concat":
[    0.772547] 0x000000000000-0x000007500000 : "ubi"
[    0.777953] ------------[ cut here ]------------
[    0.782683] WARNING: CPU: 0 PID: 1 at drivers/mtd/mtdcore.c:621 add_mtd_device+0x84/0x5f4
[    0.790983] Modules linked in:
[    0.794093] CPU: 0 PID: 1 Comm: swapper Not tainted 5.4.24 #0
[    0.799932] Stack : 80680000 8062af20 00000000 00000000 8062a0f0 87c2dae4 87c282fc 8065fd23
[    0.808430]         805c64f4 00000001 807b32d8 80670000 80670000 00000001 87c2da98 25c15bcb
[    0.816909]         00000000 00000000 807e0000 0000006e 61696e74 00000000 2e342e32 34202330
[    0.825397]         0000006e cef2ada7 00000000 000c1ded 00000000 00000009 00000000 8034de64
[    0.833889]         00000009 80670000 80670000 80676d18 00000000 80320044 00000000 807b0000
[    0.842381]         ...
[    0.844861] Call Trace:
[    0.847367] [<80069994>] show_stack+0x30/0x100
[    0.851913] [<8007e8ac>] __warn+0xc0/0x10c
[    0.856072] [<8007e954>] warn_slowpath_fmt+0x5c/0xac
[    0.861134] [<8034de64>] add_mtd_device+0x84/0x5f4
[    0.866001] [<80352a50>] add_mtd_partitions+0xd8/0x1b8
[    0.871231] [<803527b8>] parse_mtd_partitions+0x238/0x3f8
[    0.876717] [<8034e51c>] mtd_device_parse_register+0x48/0x1b0
[    0.882586] [<8038dd2c>] virt_concat_probe+0x170/0x1ec
[    0.887820] [<803334c8>] platform_drv_probe+0x40/0x94
[    0.892970] [<80331638>] really_probe+0x104/0x35c
[    0.897766] [<80331d54>] device_driver_attach+0x70/0x98
[    0.903072] [<80331ddc>] __driver_attach+0x60/0x100
[    0.908042] [<8032f668>] bus_for_each_dev+0x68/0xa4
[    0.912989] [<803309d4>] bus_add_driver+0x1f0/0x200
[    0.917952] [<80332448>] driver_register+0x84/0x148
[    0.922906] [<80060a1c>] do_one_initcall+0x7c/0x1dc
[    0.927870] [<80684e14>] kernel_init_freeable+0x158/0x23c
[    0.933361] [<805387d8>] kernel_init+0x10/0xf0
[    0.937883] [<80064dd8>] ret_from_kernel_thread+0x14/0x1c
[    0.943375] ---[ end trace 62e0927fba490f68 ]---
[...]
[    2.266513] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    2.274893] Rebooting in 1 seconds..

This patch makes mtd concat to follow new mtd requirements by registering
either normal or oob versions of read/write functions, but not both at the
same time. OOB is used only when underlying mtd devices provide such
functionality (like NAND chips) - otherwise generic methods are used.

Tested successfully on Netgear WNDR4300.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2020-03-29 16:23:57 +02:00
Evgeniy Didin
521ab1b97b archs38: switch to kernel 5.4 by default
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Petr Štetiar <ynezz@true.cz>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
2020-03-29 16:23:57 +02:00
Evgeniy Didin
b47f3bf7ec archs38: Add patch for gcc8 compilance
Building Linux kernel version 5.4.x with GCC8 ends up
with internal compiler error. The workaround on this issue
can be introdution of additional compiler option "--mmpy-option=2"

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Petr Štetiar <ynezz@true.cz>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
2020-03-29 16:23:57 +02:00
Evgeniy Didin
e3bcb83720 archs38: add kernel 5.4 config
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Petr Štetiar <ynezz@true.cz>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
[run make kernel_oldconfig CONFIG_TARGET=target]
[Do not deactivate CONFIG_NET_VENDOR_*]
[Activate CONFIG_HARDENED_USERCOPY]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-03-29 16:23:36 +02:00
Evgeniy Didin
55eb9cb72e kernel: update arc-specific patch
This patch updates arc-specific patch by moving declaration
of struct object before it's usage.

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Petr Štetiar <ynezz@true.cz>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
2020-03-29 16:05:30 +02:00
Tomasz Maciej Nowak
2d61f8821c mvebu: cortexa9: correct cpu subtype
Armada 370  processors have only 16 double-precision registers. The
change introduced by 8dcc108760 ("toolchain: ARM: Fix toolchain
compilation for gcc 8.x") switched accidentally the toolchain for mvebu
cortexa9 subtarget to cpu type with 32 double-precision registers. This
stems from gcc defaults which assume "vfpv3-d32" if only "vfpv3" as mfpu
is specified. That change resulted in unusable image, in which kernel
will kill userspace as soon as it causing "Illegal instruction".

Ref: https://forum.openwrt.org/t/gcc-was-broken-on-mvebu-armada-370-device-after-commit-on-2019-03-25/43272
Fixes: 8dcc108760 ("toolchain: ARM: Fix toolchain compilation for
gcc 8.x")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-03-28 22:58:36 +01:00
Tomasz Maciej Nowak
43d1d88510 tegra: correct cpu subtype
Tegra 2 processors have only 16 double-precision registers. The change
introduced by 8dcc108760 ("toolchain: ARM: Fix toolchain compilation
for gcc 8.x") switched accidentally the toolchain for tegra target to cpu
type with 32 double-precision registers. This stems from gcc defaults
which assume "vfpv3-d32" if only "vfpv3" as mfpu is specified. That
change resulted in unusable image, in which kernel will kill userspace as
soon as it causing "Illegal instruction".

Ref: https://forum.openwrt.org/t/gcc-was-broken-on-mvebu-armada-370-device-after-commit-on-2019-03-25/43272
Fixes: 8dcc108760 ("toolchain: ARM: Fix toolchain compilation for
gcc 8.x")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-03-28 22:58:36 +01:00
Paul Spooren
258f070d1a x86: fix missing squashfs and ext4 rootfs images
The previous rework of x86 image creation done in commit cb007a7bf6
("x86: switch image generation to new code") removed images of separate
squashfs and ext4 filesystems which are handy for example in testing
under QEMU.

So this patch adds back creation of those missing rootfs images for ext4
and squashfs based filesystems.

Fixes: cb007a7bf6 ("x86: switch image generation to new code")
Signed-off-by: Paul Spooren <mail@aparcar.org>
[commit subject and description tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:20:05 +01:00
Paul Spooren
6fcca31fc3 x86: fix padding in images
The previous rework of x86 image creation done in commit  cb007a7bf6
("x86: switch image generation to new code") broke the padding in
images.

 sda: p2 size 212992 extends beyond EOD, enabling native capacity
 sda: p2 size 212992 extends beyond EOD, truncated
 sd 0:0:0:0: [sda] Attached SCSI disk
 SQUASHFS error: squashfs_read_data failed to read block 0x2cc556
 unable to read id index table
 VFS: Cannot open root device "PARTUUID=ac5c9cd8-02" or unknown-block(8,2): error -5
 Please append a correct "root=" boot option; here are the available partitions:
 0800           19761 sda
  driver: sd
   0801           16384 sda1 ac5c9cd8-01

   0802            2865 sda2 ac5c9cd8-02

 Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,2)

Tested with x86/64 with Docker (squashfs), qemustart (ext4/squashfs) and
virtualbox (ext4/squashfs).

Ref: FS#2935
Fixes: cb007a7bf6 ("x86: switch image generation to new code")
Suggested-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Paul Spooren <mail@aparcar.org>
[commit subject and description tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Baptiste Jonglez
247043c968 ar71xx: Fix gigabit switch support for Mikrotik RB951G-2HnD
Without this patch, when using rev 3 of the Atheros AR9344 SoC, the
gigabit switch (AR8327) does not work or works very erratically.

This is a re-spin of http://patchwork.ozlabs.org/patch/419857/ with a
different PLL value, according to the feedback from several users
(including myself) as shown here:

  https://openwrt.org/toh/mikrotik/rb2011uias#tracking_reported_experience_with_suggested_patch_for_the_5_gige_ports

Performance is acceptable: testing L3 forwarding without NAT yields a
performance of 370 Mbit/s (iperf3 TCP) and 41 Kpps (iperf3 UDP with 64
bytes payload). Both tests show that 100% of CPU time is spent on softirq.

A similar fix for a different device (RB2011) was added in e457d22261
("Make GBit switch work on RB2011").

Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
2020-03-28 13:03:02 +01:00
Petr Štetiar
5ecc0cfd6f kernel: bump 5.4 to 5.4.28
Changelog since 5.4.24 mentions CVE-2019-19769, CVE-2020-8648,
CVE-2020-8649 and CVE-2020-8647.

Removed upstreamed:

 generic: 507-v5.6-iio-chemical-sps30-fix-missing-triggered-buffer-depe.patch
 generic: 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch
 bcm27xx: 950-0435-ASoC-pcm512x-Fix-unbalanced-regulator-enable-call-in.patch
 ipq806x: 701-stmmac-fix-notifier-registration.patch
 lantiq: 002-pinctrl-falcon-fix-syntax-error.patch
 octeontx: 0002-net-thunderx-workaround-BGX-TX-Underflow-issue.patch

Run tested: apu2, qemu-x86-64, apalis, a64-olinuxino, nbg6617
Build tested: sunxi/a53, imx6, x86/64, ipq40xx

Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> [apu2]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Petr Štetiar
bf15557f8a ipq40xx: switch to 5.4 kernel
5.4.24 seems to be working fine on my zyxel,nbg6617, so let's start
wider userbase testing.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Leon M. George
d59137d1d9 ipq40xx: wpj428: fix missing MDIO GPIO reset and pinmux
The bootloader does not always initialize the MDIO pins before booting
Linux. E.g. on version "U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Jul
25 2017 - 11:36:26)" this is the case when booting automatically without
activating the U-Boot console.

Without this change, the kernel boot will complain about missing PHYs:

 libphy: ipq40xx_mdio: probed
 ar40xx c000000.ess-switch: Probe failed - Missing PHYs!
 libphy: Fixed MDIO Bus: probed

With this change it will work as expected:

 libphy: ipq40xx_mdio: probed
 ESS reset ok!
 ESS reset ok!
 libphy: Fixed MDIO Bus: probed

Ref: GH-2835
Tested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit description from Fredrik, subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Petr Štetiar
c3178110b5 sunxi: switch to 5.4 kernel
Seems to be working fine on my a64-olinuxino, it's 99.9% upstream stuff
anyway. Lets start wider userbase testing.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Petr Štetiar
153a6b8c34 sunxi: a53: fix ethernet on a64-olinuxino
a64-olinuxino board has Micrel KSZ9031 Gigabit PHY so add support for
this PHY into kernel.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Petr Štetiar
8ac614fe96 sunxi: 5.4: dts: a64: olinuxino: add bank supply regulators
This is backport of v5.6 patch.

Allwinner A64 SoC has separate supplies for PC, PD, PE, PG and PL. This
patch adds regulators for them to the pinctrl node.

Exception is PL which is used by the RSB bus. To avoid circular
dependencies, VCC-PL is omitted.

On boards with eMMC, VCC-PC is supplied by ELDO1, instead of DCDC1.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Petr Štetiar
8743a9c9b9 sunxi: 5.4: a64-olinuxino: use red LED for status signalization
There is a red LED marked as `GPIO_LED1` on the silkscreen and connected
to PE17, so use this LED for status signalization.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Petr Štetiar
0784d07c11 sunxi: a53: add support for Olimex A64-Olinuxino eMMC
Specifications:

 SoC: Allwinner A64 (1.2 GHz Quad-Core ARM Cortex-A53 64-bit)
 RAM: 1GB or 2GB RAM DDR3L @ 672Mhz
 Flash: 0/4/16GB eMMC flash memory for storage and boot
 MicroSD card connector for cards up to 32GB
 Debug: serial UART debug header with 0.1" pins
 Wired connectivity: 10/100/1000Mbps GbE Ethernet
 Wireless connectivity: on-board RTL8723BS 1T1R 802.11bgn WiFi and
                        Bluetooth 4.0 module with built-in antenna
                        (only available in the A64-OLinuXino-1G4GW)

Flashing instructions:

 Standard sunxi SD card installation procedure - copy eMMC image to SD
 card, insert in into SD card slot on the device and boot. You should see
 something like following if the eMMC is detected correctly:

  mmcblk2: mmc2:0001 P1XXXX 3.60 GiB
  mmcblk2boot0: mmc2:0001 P1XXXX partition 1 16.0 MiB
  mmcblk2boot1: mmc2:0001 P1XXXX partition 2 16.0 MiB

 Then flash SD card eMMC image straight into the mmcblk2 device:

  dd if=/mnt/openwrt...a64-olinuxino-emmc-squashfs-sdcard.img of=/dev/mmcblk2

 It also possible to boot from boot0 partition[1]:

  1. Compile U-Boot with CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x40
     otherwise the U-Boot will get stuck in bootloop
  2. Configure eMMC to boot from boot0 partition inside U-Boot:

     mmc bootbus 1 1 0 0; mmc partconf 1 1 1 0

  3. echo 0 > /sys/block/mmcblk2boot0/force_ro
  4. Write U-Boot from offset 0 (not offset 8k as with SD card) into
     boot0 partition

     dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk2boot0

Known issues:

 Wireless doesn't work properly via netifd.

1. https://linux-sunxi.org/index.php?title=Bootable_eMMC

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Petr Štetiar
c31954f1cf sunxi: a53: add support for Olimex A64-Olinuxino
Specifications:

 SoC: Allwinner A64 (1.2 GHz Quad-Core ARM Cortex-A53 64-bit)
 RAM: 1GB or 2GB RAM DDR3L @ 672Mhz
 Flash: 0/4/16GB eMMC flash memory for storage and boot
 MicroSD card connector for cards up to 32GB
 Debug: serial UART debug header with 0.1" pins
 Wired connectivity: 10/100/1000Mbps GbE Ethernet
 Wireless connectivity: on-board RTL8723BS 1T1R 802.11bgn WiFi and
                        Bluetooth 4.0 module with built-in antenna
                        (only available in the A64-OLinuXino-1G4GW)

Flashing instructions:

 Standard sunxi SD card installation procedure - copy image to SD card,
 insert in into SD card slot on the device and boot.

Known issues:

 Wireless doesn't work properly via netifd.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Petr Štetiar
5217aa78f1 sunxi: a53: image: make it DRY
Replace same copy&pasted lines with the appropriate reusable bits.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Petr Štetiar
aeb6941773 bcm27xx: 5.4: add support for Sensirion SPS30 in i2c-sensor overlay
Add support for Sensirion SPS30 particulate matter sensor with fixed
address 0x69.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Thibaut VARÈNE
92616c4227 ath79: rename Mikrotik RB 922UAGS-5HPacD mtd partition
In RouterBOARD parlance there never was an "art" partition.
This partition has always been named 'hard_config' on ar71xx.

This partition contains more than just ART (Atheros Radio Test) data. It
includes the hardware description (product code, serial, board
identifier, name, hardware options, MAC address), as well as other bits
affecting the operation of RouterBoot.
To avoid confusion with regular ART data, this partition is renamed in
line with historical ar71xx and ramips nomenclature as 'hard_config'.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-27 17:12:46 +01:00
Thibaut VARÈNE
9a122df07e ath79: fix Mikrotik wAP G-5HacT2HnD mtd partitions
In RouterBOARD parlance there never was an "art" partition.
This partition has always been named 'hard_config' on ar71xx.

This partition contains more than just ART (Atheros Radio Test) data. It
includes the hardware description (product code, serial, board
identifier, name, hardware options, MAC address), as well as other bits
affecting the operation of RouterBoot.
To avoid confusion with regular ART data, this partition is renamed in
line with historical ar71xx and ramips nomenclature as 'hard_config'.

This commit fixes the previous support files and implements the nested
RouterBoot partition scheme as already used by ramips-based SPI-NOR
RouterBOARD DTSes, as previously reviewed and implemented in
bbe2cf657c ("ramips: fix RBM11G partitioning").

Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-27 17:12:46 +01:00
Alberto Bursi
43105f24eb kirkwood: fix DTS partitions for Pogoplug E02
The Pogoplug E02 was not using the correct partitions
in device tree, but used the ones from upstream and
thus could not boot OpenWrt images.

In contrast, uboot-kirkwood is using the correct
partitions since d3fc4fbd74 ("uboot-kirkwood: re-add
Pogoplug E02 support").

This patch corrects the partitions in DTS for kernels
4.14, 4.19 and 5.4.

Fixes: 2b0fa00da8 ("kirkwood: add Pogoplug E02 Kernel support")

Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[commit title/message facelift, refresh 4.14 patch]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-27 17:12:46 +01:00
John Crispin
3a8dbcf5c2 mediatke: add support for elecom-wrc-2533gent
This commit adds support for the MT7622-based Elecom WRC-2533gent router,
with spi-nand storage and 512MB RAM.

The device has the following specifications:

* MT7622 (arm64 dual-core)
* 512MB RAM (DDR3)
* 4GB storage (spi-nand)
* 5x 1Gbps Ethernet (RTL8337C switch)
* 1x UART header
* 1x USB 3.0 port
* 5x LEDs
* 1x reset button
* 1x WPS button
* 1x slider switch
* 1x DC jack for main power (12V)

The following has been tested and is working:
* Ethernet switch
* 2.4g and 5g wifi
* USB 3.0 port
* sysupgrade
* buttons/leds

Not working:
* bluetooth firmware does not load even though it is present int he rootfs

Signed-off-by: John Crispin <john@phrozen.org>
2020-03-27 16:18:57 +01:00
John Crispin
d3f058db1c mediatek: more v5.4 mtd fixes
Signed-off-by: John Crispin <john@phrozen.org>
2020-03-27 16:18:57 +01:00
Jan Alexander
d394c354ee ar71xx: use status led for GL.iNet GL-AR750S
Use power led for device status.

The status led behavior has already been fixed in af28d8a539
("ath79: add support for GL.iNet GL-AR750S") when porting the
device to ath79. This fixes it for ar71xx as well.

Signed-off-by: Jan Alexander <jan@nalx.net>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-26 19:14:25 +01:00
Adrian Schmutzler
385f4868bc ath79: add support for TP-Link TL-WA860RE v1
This ports support for the TL-WA860RE v1 range extender from ar71xx
to ath79.

Specifications:
  Board: AP123 / AR9341 rev. 3
  Flash/RAM: 4/32 MiB
  CPU: 535 MHz
  WiFi: 2.4 GHz b/g/n
  Ethernet: 1 port (100M)
  Two external antennas

Flashing instructions:
  Upload the factory image via the vendor firmware upgrade option.

Recovery:
  Note that this device does not provide TFTP via ethernet like many
  other TP-Link devices do. You will have to open the case if you
  require recovery beyond failsafe.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Sebastian Knapp <sebastian4842@outlook.com>
2020-03-26 19:14:15 +01:00
Adrian Schmutzler
676ca94c3c ath79: add support for TP-Link TL-WDR4310 v1
This device seems to be identical to the TL-WDR4300, just with
different release date/region and TPLINK_HWID.

Support is added based on the ar71xx implementation.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-26 15:05:49 +01:00
Paul Spooren
6f01d3334e x86/geode: fixup FEATURE inheritance
In the geode subtarget all default x86 features were overwritten via :=
instead of extending them via +=.

This patch fixes the inheritance and thereby the compilation of
x86/geode target.

Compile tested x86/geode.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-03-23 18:56:26 +00:00
Paul Spooren
3f3a754c68 x86/geode: add missing include after rebase
The x86 image generation was refacted via cb007a7bf6 and accidently not
included `geode.mk` when selected as subtarget.

Now the file is included and image compilation for x86/geode works
again.

Thanks to Russell Senior <russell@personaltelco.net> for reporting the
problem and suggesting a patch!

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-03-23 10:42:53 +00:00
Álvaro Fernández Rojas
340fc3a1c6 bcm27xx: refresh linux 5.4 configs
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-03-23 09:14:36 +01:00
Álvaro Fernández Rojas
6c9b5d6972 bcm27xx: sync 5.4 patches with RPi Foundation
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-03-23 08:48:08 +01:00
Christian Lamparter
8a92ae8e4b apm821xx: switch to 5.4 kernel
This patch switches the APM821XX target to the linux kernel 5.4 variant.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-03-22 23:02:09 +01:00
Christian Lamparter
3509d4ec56 apm821xx: wndr4700: add preliminary drivetemp sensor
This patch prepares the WNDR4700 to use the HDD sensor for
the thermal zone. While the kernel's thermal.txt device-tree
binding documentation files talks about supporting multiple
sensors for a zone. This sadly is NOT the case. Even the most
current upstream kernels (5.6-rc) supports just >one< sensor
per zone: (driver/base/of-thermal.c:886)
| * REVIST: for now, the thermal framework supports only
| * one sensor per thermal zone. Thus, we are considering
| * only the first two values as slope and offset.

I do hope that this warning will prevent others wasteing time
on trying to figure out why their multi-sensor thermal-zones
definitions are not working as specified.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-03-22 23:02:09 +01:00
Christian Lamparter
01fe7a2b64 apm821xx: add drivetemp sensor for the WD MyBook Series
This patch adds the hwmon-drivetemp to the device.
It also adds device-tree bindings. This can be useful to
automate external fans which can be controlled for example
by either an unused sata-port or by the usb-power regulator.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-03-22 23:02:09 +01:00
Christian Lamparter
0409fe64cf x86: geode/legacy: fix missing watchdog core dependencies
This patch follows the other patches that added the watchdog
core to various (armvirt, malta, ath79, ...) targets that
have been hit by the following build error:

Package kmod-hwmon-sch5627 is missing dependencies for the following libraries:
watchdog.ko

In theory, we could have just added the CONFIG_WATCHDOG_CORE=y
to the Kconfig variable of kmod-hwmon-sch5627's package definition.
This would have forced the watchdog core to be builtin and less
architectures would need to be updated. But we might as well follow
through here.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-03-22 23:02:09 +01:00
David Bauer
f1f8700d54 ath79: fix missing return statement in ar934x_nand
The reset assert and deassert methods currently miss
a return value, leading to a compilation warning.

Return the return-value of reset_control_assert and
reset_control_deassert to fix these warnings.

Suggested-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-03-22 20:09:44 +01:00
David Bauer
94c0926106 ath79: fix NAND driver compilation for kernel 5.4
This fixes the compilation of the AR934x NAND controller
driver for kernel 5.4 while leaving it untouched for
kernel 4.19.

This change is currently not run-tested, as i do not have such
a device at hand.

CC: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
CC: André Valentin <avalentin@marcant.net>
CC: WeiDong Jia <jwdsccd@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2020-03-22 20:03:18 +01:00
Daniel Golle
9e5a25846f oxnas: yet another irqchip related patch
This time DTS fix, again from Sungbo Eo <mans0n@gorani.run>
  ARM: dts: oxnas: Fix clear-mask property

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-03-22 13:37:37 +00:00
David Bauer
280868e54d ath79: align Ubiquiti AC Pro ethernet map to factory
The Uniquiti AC Pro and Ubiquiti AC Mesh Pro currently have the
"Primary" and "Secondary" ethernet ports configured to offer LAN as well
as WAN. However, Uiquiti describes the following behavior for the
devices Ethernet ports:

 > Secondary UniFi Access Point (UAP) Ethernet ports don't
 > provide PoE passthrough (to run current to a second powered
 > device), but they do support data passthrough.
 > It serves as a bridged interface between main / secondary
 > Ethernet port.

To reduce confusion for users (as LAN and WAN functionality is not
visible on the device itself), configure both ports to offer LAN
functionality. Users can still configure a WAN interface on a port they
are able to choose.

CC: Lucian Cristian <lucian.cristian@gmail.com>
Reported-by: Florian Klink <flokli@flokli.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-03-22 02:08:02 +01:00
Roger Pueyo Centelles
1775d50bde ath79: add support for Ubiquiti NanoBridge M (XM)
This patch adds support for the Ubiquiti NanoBridge M (XM), a
802.11n wireless with a feed+dish form factor, with the same board
definition as the Bullet M (XM).

Specifications:
 - Atheros AR7241 SoC
 - 32 MB RAM
 - 8 MB SPI flash
 - 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in
 - Power and LAN green LEDs
 - 4x RSSI LEDs (red, orange, green, green)
 - UART (115200 8N1)

Flashing via stock GUI:
 - WARNING: flashing OpenWrt from AirOS v5.6 or newer will brick your
   device! Read the wiki for more info.
 - Downgrade to AirOS v5.5.x (latest available is 5.5.11) first.
 - Upload the factory image via AirOS web GUI.

Flashing via TFTP:
 - WARNING: flashing OpenWrt from AirOS v5.6 or newer will brick your
   device! Read the wiki for more info.
 - Downgrade to AirOS v5.5.x (latest available is 5.5.11) first.
 - Use a pointy tool (e.g., pen cap, slotted screwdriver) to keep the
   reset button pressed.
 - Power on the device (keep reset button pressed).
 - Keep pressing until LEDs flash alternatively LED1+LED3 =>
   LED2+LED4 => LED1+LED3, etc.
 - Release reset button.
 - The device starts a TFTP server at 192.168.1.20.
 - Set a static IP on the computer (e.g., 192.168.1.21/24).
 - Upload via tftp the factory image:
    $ tftp 192.168.1.20
    tftp> bin
    tftp> trace
    tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanobridge-m-squashfs-factory.bin

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, fix includes in DTS, add label MAC address, add SOC and
fix sorting in generic-ubnt.mk]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-22 00:54:44 +01:00
Rafał Miłecki
8abefc8896 bcm53xx: sysupgrade: optimize building UBI image
Use "truncate" to adjust size of existing file instead of "dd" which
required creating a copy. This saves space on tmpfs. It may be as low
as 2.1 MiB when using OpenWrt default user space and way more (20+ MiB)
when flashing vendor firmware.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-03-21 22:31:35 +01:00
Sungbo Eo
3f14f034fb treewide: omit IMAGE_SIZE argument from check-size
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-21 20:02:55 +01:00
Sungbo Eo
5b392c7119 treewide: gather DEVICE_VARS into one place
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.

For ramips, remove redundant values already present in parent file.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-21 19:55:12 +01:00
Russell Senior
d5812478ad ath79: add support for ubnt_bullet-m-ar7240 variant
This adds support for the Ubiquiti Bullet M (AR7240).

Specifications:
- AR7240 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- External antenna
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB

Flashing via WebUI:
  Upload the factory image via the stock firmware web UI.

  Attention: airOS firmware versions >= 5.6 have a new bootloader with
  an incompatible partition table!

  Please downgrade to <= 5.5 _before_ flashing OpenWrt!
  Refer to the device's Wiki page for further information.

Flashing via TFTP:
  Same procedure as other Ubiquiti M boards.

- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
  button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
  LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
  $ tftp 192.168.1.20
  tftp> bin
  tftp> trace
  tftp> put openwrt-ath79-generic-xxxxx-ubnt_bullet-m-ar7240-squashfs-factory.bin

The "fixed-link" section of the device tree is needed to avoid errors like this:

  Generic PHY mdio.0:1f:04: Master/Slave resolution failed, maybe conflicting manual settings?

With "fixed-link", the errors go away and eth0 comes up reliably.

Signed-off-by: Russell Senior <russell@personaltelco.net>
[fix SUPPORTED_DEVICES]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-21 19:22:21 +01:00
Linus Walleij
349ad62341 gemini: Bump kernel to v5.4
The v5.4 kernel already works much better than v4.19
as so many things got upstreamed so let's just bump
it to kernel v5.4.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-03-21 18:17:04 +01:00
Linus Walleij
7fc155fd41 gemini: Add kernel config for kernel v5.4
This adds a kernel config file for the v5.4 gemini
kernel.

No major changes compared to v4.19, mainly
CONFIG_MTD_PHYSMAP_OF_GEMINI was renamed to
CONFIG_MTD_PHYSMAP_GEMINI.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[select UNWINDER_ARM, set CONFIG_DRM_FBDEV_OVERALLOC, drop
dropped 4.19 symbols, kernel config refreshed]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-03-21 18:16:49 +01:00
Linus Walleij
ea2d284082 gemini: Add v5.4 kernel patches
This adds the kernel patches needed for the Gemini.
Just 7 patches, 5 of them are already upstream.

Notably we incorperate the temperature sensor on the
hard drive to drive temperature control of the NAS
chassis. This is required for the DIR-685 which has
no external temperature sensor.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[use the drivetemp package over the backport]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-03-21 17:50:43 +01:00
Christian Lamparter
711bd33cd1 kernel: 5.4: disable more symbols
These have been discovered by the gemini 5.4 patches.
This is because one of the devices uses the FBDEV emulation.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-03-21 17:50:43 +01:00
Christian Lamparter
d107aaa910 kernel: backport and package drivetemp hwmon from v5.5
This patch backports the hwmon drivetemp sensor module from vanilla
linux 5.5 to be available on OpenWrt's 5.4 kernel.

Extract from The upstream commit by Guenter Roeck <linux@roeck-us.net>:
hwmon: Driver for disk and solid state drives with temperature sensors

"Reading the temperature of ATA drives has been supported for years
by userspace tools such as smarttools or hddtemp. The downside of
such tools is that they need to run with super-user privilege, that
the temperatures are not reported by standard tools such as 'sensors'
or 'libsensors', and that drive temperatures are not available for use
in the kernel's thermal subsystem.

This driver solves this problem by adding support for reading the
temperature of ATA drives from the kernel using the hwmon API and
by adding a temperature zone for each drive.

With this driver, the hard disk temperature can be read [...]
using sysfs:

$ grep . /sys/class/hwmon/hwmon9/{name,temp1_input}
/sys/class/hwmon/hwmon9/name:drivetemp
/sys/class/hwmon/hwmon9/temp1_input:23000

If the drive supports SCT transport and reports temperature limits,
those are reported as well.

drivetemp-scsi-0-0
Adapter: SCSI adapter
temp1:        +27.0<C2><B0>C (low  =  +0.0<C2><B0>C, high = +60.0<C2><B0>C)
                             (crit low = -41.0<C2><B0>C, crit = +85.0<C2><B0>C)
                             (lowest = +23.0<C2><B0>C, highest = +34.0<C2><B0>C)

The driver attempts to use SCT Command Transport to read the drive
temperature. If the SCT Command Transport feature set is not available,
or if it does not report the drive temperature, drive temperatures may
be readable through SMART attributes. Since SMART attributes are not well
defined, this method is only used as fallback mechanism."

This patch incorperates a patch made by Linus Walleij:
820-libata-Assign-OF-node-to-the-SCSI-device.patch
This patch is necessary in order to wire-up the drivetemp
sensor into the device tree's thermal-zones.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-03-21 17:48:34 +01:00
Daniel Golle
19af00850f oxnas: backport another fix for irqchip
Sungbo Eo <mans0n@gorani.run> submitted another patch fixing an error
on reboot:
  irqchip/versatile-fpga: Apply clear-mask earlier

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-03-21 14:26:26 +00:00
Paul Spooren
30a2488290 x86: allow non gzipped images
The previous image generation code would always gzipped images.

This patch changes the behaviour and only compresses images when
selected in menuconfig.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-03-21 10:36:00 +00:00
Paul Spooren
33cc7e763b x86: use qemu-image command from image-commands.mk
The `qemu-image` command converts images to the specified type and
reduces redundant code.

Adaption from Alexander Couzens <lynxis@fe80.eu> work[0].

[0]: https://git.openwrt.org/?p=openwrt/staging/lynxis.git;a=blob;f=target/linux/x86/image/Makefile;h=83b8140b7aefbe708fd09c9c61827e7e39bda8b4;hb=416cccf398e9589e3de386e05b61b1c46cace20d#l51

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-03-21 10:36:00 +00:00
Paul Spooren
b2207e267b x86: remove obsolete legacy profiles
Rely on device profiles instead for packages selection.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rebase, adjusted commit title]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-03-21 10:36:00 +00:00
Paul Spooren
cb007a7bf6 x86: switch image generation to new code
This commit introduces few related changes which need to be done in
single commit to keep images buildable between git revisions. In result
it retains all previous image creation possibilities with slight name
change of generated images. Brief summary of the commit:

* Split up image generation recipe to smaller chunks to make it more
  generic and reusable.

* Make iso images x86 specific and drop their definition as root
  filesystem.

* Convert image creation process to generic code specified in image.mk.

* Make geode subtarget inherit features from the main target instead of
  redefining them.

* For subtargets create device definitions with basic packages set.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rebased]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-03-21 10:36:00 +00:00
Paul Spooren
5a5df62d95 x86/grub2: move grub2 image creation to package
Let the grub2 package take care of creating installable grub2 images,
this will allow creating grub2 images without first calling x86 image
generation recipe. Also as side effect, since those images are now
shared, it'll reduce the number of calling grub-mkimage.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rebase, adjusted commit title]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-03-21 10:36:00 +00:00
Kevin Darbyshire-Bryant
e6e1e12dc3 kernel: connmark set-dscpmark fix build on 5.4
Fix header change that was done for kernel but 4.19 got missed for 5.4.

Solves nasty errors like:

8.4.0_musl/include/linux/netfilter/xt_CONNMARK.h:5,
                from connmark_listener.c:30:
/builder/shared-workdir/build/sdk/staging_dir/toolchain-aarch64_cortex-a53_gcc-8.4.0_musl/include/linux/netfilter/xt_connmark.h:23:2: error: enumerator value for 'XT_CONNMARK_VALUE' is not an integer constant
 XT_CONNMARK_VALUE = BIT(0),
 ^~~~~~~~~~~~~~~~~
/builder/shared-workdir/build/sdk/staging_dir/toolchain-aarch64_cortex-a53_gcc-8.4.0_musl/include/linux/netfilter/xt_connmark.h:25:1: error: enumerator value for 'XT_CONNMARK_DSCP' is not an integer constant
};

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-03-21 09:51:40 +00:00
Chuanhong Guo
ed7751f968 mediatek: move mt76 and wpad-bacic to mt7622 subtarget
mt76 is a target default package for mt7622-wmac only.
mt7623 doesn't have integrated wireless support and wifi drivers for
pcie cards should be added as device specific package.
mt7629-wmac isn't supported by mt76 yet.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-03-21 12:58:29 +08:00
Chuanhong Guo
b7fe92b915 mediatek: mt7629: fix firmware partition
rename "kernel" partition in upstream dts to "firmware" and add
denx,fit as compatible string for mtdsplit.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-03-21 12:58:29 +08:00
Chuanhong Guo
2d2e9d2956 mediatek: backport spi-mem based mtk spinor driver
This new driver has full quadspi and DMA support, providing way better
reading performance.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-03-21 12:58:29 +08:00
Chuanhong Guo
a73ee0fe35 mediatek: mt7629: refresh config for linux 5.4
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-03-21 12:58:29 +08:00
Chuanhong Guo
1bbb8807fa mediatek: mt7629: fix ethernet default config
1. fix typo: ucidef_set_interfaces_wan -> ucidef_set_interface_wan
2. change board name to mt7629-rfb to match upstream dts

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-03-21 12:58:29 +08:00
Serge Vasilugin
9801d61c4a kernel: rtl8367b: add configuration for extif2
Both rtl8367b and rtl8367s have two extended interface
rtl8367rb: 5 port + 2*RGMII/MII
rtl8367s:  5 port + SGMII/HSGMI + RGMII/MII
(?)rtl8367sb:  5 port + 2*RGMII/MII
These interfaces correspond to EXT1 and EXT2 (ports 6 and 7 respectivly).

This patch allow to configure EXT2 in dts-file:

	rtl8367rb {
		compatible = "realtek,rtl8367b";
		cpu_port = <7>;
		realtek,extif2 = <1 0 1 1 1 1 1 1 2>;
		mii-bus = <&mdio0>;
		phy_id = <29>;
	};

Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
[fix indent, replace magic value, alter commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-03-21 12:58:29 +08:00
Chuanhong Guo
c0bc706c31 generic: rtl8367b: add definition of debug reg
This commit adds definition of DEBUG0 and DEBUG1 registers and replace
magic values with proper register modifying.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-03-21 12:58:29 +08:00
Daniel Golle
67b04e767a oxnas: backport patch fixing hang after reboot
Sungbo Eo <mans0n@gorani.run> posted a patch fixing the long-standing
reboot problem on the OXNAS OX820 platform:
  irqchip/versatile-fpga: Handle chained IRQs properly

It got queued for 5.7. Import it to oxnas target patches for now.

Fixes: b4917fa907 ("oxnas: fix oxnas-rps-timer dt-match")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-03-19 22:48:23 +00:00
Davide Fioravanti
213250b56b ath79: add support for TP-Link Archer D7/D7b v1
TP-Link Archer D7 v1 is a dual-band AC1750 router + modem.
The router section is based on Qualcomm/Atheros QCA9558 + QCA9880.
The "DSL" section is based on BCM6318 but it's currently not supported.

The Archer D7b seems to differ from the Archer D7 only in the
partition table.

Router section - Specification:

775/650/258 MHz (CPU/DDR/AHB)
128 MB of RAM (DDR2)
16 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
4x 10/100/1000 Mbps Ethernet
7x LED, 2x button
UART header on PCB

Known issues:

- Broadband LED (missing GPIO - probably driven by the BCM6318)
- Internet LED (missing GPIO - probably driven by the BCM6318)
- WIFI LED (working only for one interface at a time, while in the
  OEM firmware works for both wifi interfaces; thus, this patch does
  not set a trigger by default)
- DSL not working (eth0)

UART connection
---------------
J1 HEADER (Qualcomm CPU)
. VCC
. GND
. RX
O TX

J41 HEADER (Broadcom CPU)
. VCC
. GND
. RX
O TX

The following instructions require a connection to the J1 UART header
and are tested for the Archer D7 v1.
For the Archer D7b v1, names should be changed accordingly.

Flash instructions under U-Boot, using UART
------------------------------------------
 1. Press "tpl" to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-squashfs-sysupgrade.bin
	erase 0x9f020000 +f90000
	cp.b 0x81000000 0x9f020000 0xf90000
	reset

Initramfs instructions under U-Boot for testing, using UART
----------------------------------------------------------
 1. Press "tpl" to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-initramfs-kernel.bin
	bootm 0x81000000
 4. Here you can backup the original firmware and/or flash the sysupgrade openwrt if you want

Restore the original firmware
-----------------------------
 0. Backup every partition using the OpenWrt web interface
 1. Download the OEM firmware from the TP-Link website
 2. Extract the bin file in a folder (eg. Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin)
 3. Remove the U-Boot and the Broadcom image part from the file.
    Issue the following command:
	dd if="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin" of="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod" skip=257 bs=512 count=31872
 4. Double check the .mod file size. It must be 16318464 bytes.
 5. Flash it using the OpenWrt web interface. Force the update if needed.
    WARNING: Remember to NOT keep settings.

 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
     Issue below commands in the U-Boot:
	tftpboot 0x81000000 Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod
	erase 0x9f020000 +f90000
	cp.b 0x81000000 0x9f020000 0xf90000
	reset

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[cosmetic DTS changes, remove TPLINK_HWREVADD := 0, do not use two
phyXtpt at once, add missing buttons, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-18 14:25:38 +01:00
Adrian Schmutzler
646d95c374 ath79: add support for TP-Link Archer C60 v3
TP-Link Archer C60 v3 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561 + QCA9886.

It seems to be identical to the v2 revision, except that
it lacks a WPS LED and has different GPIO for amber WAN LED.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 2x button
- UART header on PCB

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
   directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server
8. Wait ~30 second to complete recovery

While TFTP works for OpenWrt images, my device didn't accept the
only available official firmware "Archer C60(EU)_V3.0_190115.bin".

In contrast to earlier revisions (v2), the v3 contains the (same)
MAC address twice, once in 0x1fa08 and again in 0x1fb08.
While the partition-table on the device refers to the latter, the
firmware image contains a different partition-table for that region:

name           device            firmware
factory-boot   0x00000-0x1fb00   0x00000-0x1fa00
default-mac    0x1fb00-0x1fd00   0x1fa00-0x1fc00
pin            0x1fd00-0x1fe00   0x1fc00-0x1fd00
product-info   0x1fe00-0x1ff00   0x1fd00-0x1ff00
device-id      0x1ff00-0x20000   0x1ff00-0x20000

While the MAC address is present twice, other data like the PIN isn't,
so with the partitioning from the firmware image the PIN on the device
would actually be outside of its partition.
Consequently, the patch uses the MAC location from the device (which
is the same as for the v2).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-18 13:49:06 +01:00
Russell Senior
8cacb84041 ath79: rename ubnt_bullet-m to ubnt_bullet-m-ar7241
Since there exists another variant of the Bullet M with AR7240 SoC
under the same name, this patch introduces the SoC into the device
name to be able to distinguish these variants.

Signed-off-by: Russell Senior <russell@personaltelco.net>
[add commit message, adjust model in DTS, fix 02_network and
SUPPORTED_DEVICES]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-18 13:45:57 +01:00
Russell Senior
572278d3a0 ath79: generalize ubnt_xm dtsi for ar7240 and ar7241
* Prepare to support the AR7240 variant of ubiquiti bullet m, by
  reorganizing the related dtsi files.

* Distribute SOC variable across ubnt-xm devices.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2020-03-18 13:45:57 +01:00
Bjørn Mork
dabe8471fc bcm27xx: enable THERMAL_WRITABLE_TRIPS on bcm2710 and bcm2711
The PoE hat supported on the RPi 3B+ and 4B comes with a rather
loud fan, tripped in two steps by the brcmstb_thermal
thermal_zone driver.  Enabling writable trip points allow
users to adjust the fan trip points according to their
preferred temp/noise ratio.

This setting is enabled on most other targets with similar
thermal_zone controlled cooling devices.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2020-03-18 12:19:13 +01:00
Mathias Kresin
132ff90f1d ramips: do not add metadata to factory images
The image metadata are openwrt specific and not required for factory
images.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-17 22:17:59 +01:00
Mathias Kresin
b66af9ac2d lantiq: kernel 5.4: enable JFFS2
We do not build images with a jffs2 rootfs, but jffs2 is still used as
filesystem for the rootfs_data.

Fixes: e3eaf57808 ("lantiq: kernel 5.4: debloat kernel config")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-17 20:36:39 +01:00
Adrian Schmutzler
a57fcd880e ath79: fix execute bit for 02_network on mikrotik subtarget
When creating the mikrotik subtarget, the execute bit on 02_network
was not set. Fix it.

Fixes: a66eee6336 ("ath79: add mikrotik subtarget")

Reported-by: Christopher Hill <ch6574@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-17 19:24:29 +01:00
Adrian Schmutzler
3d8be08939 ath79: get rid of BOARD_NAME for Mikrotik RouterBOARD
So far, specifying "BOARD_NAME := routerboard" is required by the
upgrade code of Mikrotik NAND devices, as "sysupgrade-routerboard"
is hardcoded in platform_do_upgrade_mikrotik_nand().

This patch replaces the latter with a grep for the name like it
is already done in nand_upgrade_tar() in /lib/upgrade/nand.sh.

By that, BOARD_NAME is obsolete now for this device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-17 12:05:45 +01:00
Adrian Schmutzler
281785d74f ar71xx: remove hard-coded folder name from Mikrotik RB upgrade
So far, specifying "BOARD_NAME := routerboard" is required by the
upgrade code of Mikrotik NAND devices, as "sysupgrade-routerboard"
is hardcoded in platform_do_upgrade_mikrotik_rb().

This patch replaces the latter with a grep for the name like it
is already done in nand_upgrade_tar() in /lib/upgrade/nand.sh.

This should enable upgrades from ar71xx to ath79 without setting
BOARD_NAME for the latter.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-17 12:02:14 +01:00
Roger Pueyo Centelles
a66eee6336 ath79: add mikrotik subtarget
This commit creates the ath79/mikrotik subtarget in order to support
MikroTik devices based on Qualcomm Atheros MIPS SoCs.

MikroTik devices need a couple of specific features: the split MiNOR
firmware MTD format, which is not used by other devices, and the 4k
sector erase size on SPI NOR storage, which can not be added to the
ath79/generic and ath79/nand subtargets now.

Additionally, the commit moves the two MikroTik devices already in
the generic and nand subtargets to this new one.

Tested on the RB922 board and the wAP AC router.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-03-17 11:50:47 +01:00
Sungbo Eo
9e129c9d95 oxnas: enable sata on Pogoplug V3/Pro
Pogoplug V3/Pro has an interanl SATA port. To use it, DTS sata node should be
enabled, and kmod-ata-oxnas-sata package needs to be installed.

Fixes: FS#2542

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-03-17 17:36:34 +09:00
Tomasz Maciej Nowak
6e64039a87 tegra: switch to kernel 5.4
Build the latest kernel by default, since testing did not show any
regressions.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[fix merge conflict in tegra/Makefile]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-17 00:51:48 +01:00
Tomasz Maciej Nowak
d42abe544e tegra: refresh patches and kernel config for 5.4
This commit also disables Trusted Foundations firmware support as this
feature won't be used by any device.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[fix merge conflict in tegra/Makefile]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-17 00:51:48 +01:00
Tomasz Maciej Nowak
86c939841c tegra: copy kernel config and patches for 5.4
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-03-17 00:51:48 +01:00
Tomasz Maciej Nowak
ddc0e87fae kernel: move TEO governor to generic config
This new symbol popped up in few places. Disable it in generic config.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[fixed merge conflict in generic/config-5.4]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-17 00:51:48 +01:00
Michael Heimpold
c8946a5baf mxs: fix user led for OLinuXino boards
More testing after kernel upgrade to 5.4 uncovered a regression: the user
led is not present anymore due to a pin mux "collision" in device tree.

A patch sent to upstream kernel was accepted now. Integrate this
pending fix as platform specific patch so that user led is available again.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2020-03-17 00:51:48 +01:00
Luis Araneda
c48cf5ddb3 zynq: switch to kernel 5.4
Use kernel 5.4 by default

compile-tested: all devices from target
run-tested: Digilent Zybo Z7-20

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2020-03-17 00:51:48 +01:00
Luis Araneda
badedbf007 zynq: refresh kernel 5.4 config
By running make kernel_oldconfig and selecting relevant options

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2020-03-17 00:51:48 +01:00
Luis Araneda
2cad8341da zynq: copy config from kernel 4.19 to 5.4
Refreshed kernel 4.19 config before copying the file

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2020-03-17 00:51:48 +01:00
Mathias Kresin
e3eaf57808 lantiq: kernel 5.4: debloat kernel config
The etop driver is used by all targets except xrx200.

Remove the UBIFS compression support for zlib and zstd from the xway
subtarget. The hardware is EOL for a long time and it's unlikely to ever
see a board shipped with an UBIFS using these compression methods.

Remove the JFFS2 support. Support for jjfs2 images was dropped years
ago.

It shrinks the compressed kernel up to 130 KByte.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-16 22:28:17 +01:00
Mathias Kresin
6bf179b270 lantiq: add Linux 5.4 support as testing kernel version
Switch to the mainline Lantiq PCIe PHY driver and update the vr9.dtsi
accordingly.

The Lantiq IRQ SMP support added upstream required changes to the SoC
dtsi as well.

Following changes are made to the Lantiq kernel patches:

  0005-lantiq_etop-pass-struct-device-to-DMA-API-functions.patch
  0006-MIPS-lantiq-pass-struct-device-to-DMA-API-functions.patch
    applied upstream

  0008-MIPS-lantiq-backport-old-timer-code.patch
    access_ok API update because it lost it's type (which was the first)
    parameter in upstream commit 96d4f267e40f95 ("Remove 'type' argument
    from access_ok() function")

  0024-MIPS-lantiq-autoselect-soc-rev-matching-fw.patch
    merged into 0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch

  0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch
    revert upstream changes required for upstream xrx200 ethernet and
    xrx200 (DSA) switch driver but breaking our driver

  0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch
    required for our driver but dropped upstream, add former upstream
    version

  0028-NET-lantiq-various-etop-fixes.patch
    now has to use the phy_set_max_speed API instead of modifying
    phydev->supported. Also call ltq_dma_enable_irq() in
    ltq_etop_open() based on upstream commit cc973aecf0b054 ("MIPS:
    lantiq: Do not enable IRQs in dma open")

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2020-03-16 22:28:17 +01:00
Martin Blumenstingl
3d5d56487d lantiq: linux 5.4: remove support for the linux,mtd-name OF property
This is referenced in two .dts but never actually used from userspace.
Drop support for this property because it's not used and because it
makes updating to Linux 5.4 harder (as the patch doesn't apply anymore).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2020-03-16 22:28:16 +01:00
Mathias Kresin
005dedd348 lantiq: copy target to kernel 5.4
Duplicate kernel 4.19 config and patches for kernel 5.4.

Duplicate the devicetree source files as well, they need kernel 5.4
specific adjustments.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-16 22:28:16 +01:00
Mathias Kresin
095598ce00 generic: make all phy drivers kernel 5.0 compatible
It adjusts the code to upstream changes from the commit 3c1bcc8614db
("net: ethernet: Convert phydev advertize and supported from u32 to link
 mode")

Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-16 22:28:16 +01:00