Removed following upstreamed patch:
* bcm53xx: 081-next-ARM_dts_BCM53015-add-mr26.patch
All other patches automagically rebased.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There are forum reports that 2 LAN ports are still not working,
the phy-mode settings are adjusted to fix the problem.
Fixes: #10371
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
There are forum reports that 2 LAN ports are not working, the
GPIO settings are adjusted to fix the problem.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
lantiq,bus-clock, interrupt-map-mask and interrupt-map are already
defined with these exact values in vr9.dtsi. Drop them from
vr9_tplink_tdw8980.dts to just have one place where these are
maintained.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ar9.dtsi and danube.dtsi only have one reset controller and they are
naming it "reset". This is equivalent to "reset0" in vr9.dtsi. Fix the
references to the reset controller in the recently added PCI controller
reset line.
Fixes: 087f2cba26 ("lantiq: dts: Add the reset line for the PCI controller")
Reported-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
The PCI controller has it's reset line wired up to bit 13 of RCU.
Describe this in our .dtsi files.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
FRITZ!Box 7360 V2 and FRITZ!Box 7360 SL both use GPIOs 37 (for &phy0)
and GPIO 44 (for &phy1) to control the PHY's reset lines. FRITZ!Box 7362
SL however uses GPIO 45 (for &phy0) and GPIO 44 (for &phy1). Move the
GPIO reset definitions to each individual board .dts and while at it,
fix the GPIOs for the FRITZ!Box 7362 SL.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This commit replaces patch number 0703 with the upstream accepted
version. This patch requires backporting an additional patch to
avoid conflicts.
The only significant change is the lower maximum MTU. Packets with
lengths over 2400 may be dropped.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Without a partition subnode ofpart_core still parses direct subnodes as
partitions, but it ignores nodes with a compatible property. Due to
this, the switch to nvmem-cells made the urlader partition inaccessible.
As a result, the wireless network was broken, as the calibration data
is read from that partition by a script.
Fixes: #8983
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The &spi node has #address-cells = <1> and #size-cells = <0>. Drop the
extra 0 in the reg property from the SPI flash node to ensure it's
number of cells matches the definition in the parent node. This also
makes the reg property for the SPI flash node consistent with all other
VR9 boards.
Fixes: eae6cac6a3 ("lantiq: add support for AVM FRITZ!Box 7362 SL")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
The skb->len field is read after the packet is sent to the network
stack. In the meantime, skb can be freed. This patch fixes this bug.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
After enhancing ltq-deu, build it by default for the devices
using it.
Reverts: 964863b ("ltq-deu: Mark lantiq DEU broken")
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This patch includes a series of performance improvements. All patches
were accepted and should land in 5.17.
NAT Performance results on BT Home Hub 5A (kernel 5.10.89, mtu 1500):
Down Up
Before 539 Mbps 599 Mbps
After 624 Mbps 695 Mbps
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
xrx200 max MTU is reduced so that it works correctly when set to the
max, and the max MTU of the switch is increased to match.
In 5.10, the switch driver now enables non-standard MTUs on a per-port
basis, with the overall frame size set based on the cpu port. When the
MTU is not used, this should have no effect. The maximum packet size is
limited as large packets cause the switch to lock up.
0702-net-lantiq-add-support-for-jumbo-frames.patch comes from net-next
commit 998ac358019e491217e752bc6dcbb3afb2a6fa3e.
In 5.4, all switch ports are configured to accept the max MTU, as 5.4
does not have port_max_mtu/port_change_mtu callbacks.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
It was reported the caldata on the FritzBox 7430 is not only stored at
different offsets, but is also larger than the current output size
limit.
Increase the output file size limit (after deflate) by 1024 bytes.
Ref: FS#3604 ("ath9k firmware is 0 bytes on Fritzbox 7430")
Signed-off-by: David Bauer <mail@david-bauer.net>
It was reported the AVM FritzBox 7430 has different offsets for the
caldata depending on the device.
Whether this is due to custom bad-block handling or up to the installed
bootloader-version is unknown.
Try both known caldata offsets like it is already done for the ipq40xx
NAND based models. Use the same approach for the FritzBox 7412. While it
is currently unknown, whether it is affected, applying the same logic
has no downsides.
Signed-off-by: David Bauer <mail@david-bauer.net>
All buttons of the FritzBox 7360 family are active-low, not active-high.
Corrent the GPIO flag. This fixes release triggers upon push of a button.
Reported-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Signed-off-by: David Bauer <mail@david-bauer.net>
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2
either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
adds the correct offset for the calibration data.
The values are according to the OpenWrt Forum Thread:
"Fritzbox 7430 and wifi".
Link: <https://forum.openwrt.org/t/fritzbox-7430-and-wifi/86944>
Reported-by: RENErica
Signed-off-by: Joel Linn <jl@conductive.de>
[changed commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The xway_legacy subtarget only supports 5 devices. Most compiled
switch drivers are unused by any of these devices. The same drivers
are compiled into the xway subtarget. They were probably copied
from there when creating this subtarget.
Switches used by devices:
Arcadyan ARV4518PWR01 Realtek RTL8306SD
Arcadyan ARV4518PWR01A Realtek RTL8306SD
Arcadyan ARV4520PW Infineon ADM6996I
Arcadyan ARV4525PW only PHY(IC+ IP101A)
Arcadyan ARV452CQW Realtek RTL8306
The CONFIG_ETHERNET_PACKET_MANGLE symbol has also been disabled,
as it is only needed by the driver for AR8216.
Reduces kernel size by 19.9 kB.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
The board has a fixed size kernel partition but do not limit the kernel
size during image building.
Disable image building for both boards as well, since the kernel of the
last release as well as master are to big to fit into the 2 MByte kernel
partition.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The current state of the kernel 5.4 support is in the openwrt-21.02
branch. No need to keep a not default used kernel in this branch.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [VRX268/ bthub5]
With Kernel 5.10 the ar7 FRITZ!Box are not booting the initramfs nor the
sysupgrade image any more. Presumably due to the grown kernel.
Use the okli preloader to workaround the bootloader issue. No solution
so far for the initramfs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Removed due to being unused with 1f7a03a706, but now required for the
ar7 FRITZ!Box.
Could be used for the ARV7519RW22 as well, for which the image
generation was disabled due to a stock u-boot issue with kernel bigger
than 2 MByte.
The code is combination of the ath79 and ramips okli loader.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit contains a series of fixes for DMA. The burst length
patch significantly improves Ethernet performance. Patches were
tested on the xRX200 and xRX330.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
The devicetree property mac-address is expected to be set by the
bootloader and has priority over the nvmem supplied one.
Drop the mac-address address property from the dtsi files, to let the
mac address from nvmem-cells get used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
OpenWrt maintains two special out-of-tree DT properties:
"qca,disable-5ghz" and "qca,disable-2ghz". These are implemented
in a mac80211 ath9k patch "550-ath9k-disable-bands-via-dt.patch".
With the things being what they are, now might be a good
point to switch the devices to the generic and upstream
"ieee80211-freq-limit" property. This property is much
broader and works differently. Instead of disabling the
drivers logic which would add the affected band and
channels. It now disables all channels which are not
within the specified frequency range.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # HH5A
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
When trying to add support for another device with Micron NAND chips,
it was discovered that the default setting in the kernel source does
not work with Micron Chips, since the device trees setting is
overwritten and hard coded by the kernel xway_nand driver. This was
the original reason for this PR.
A kernel patch sets the default ECC mode to soft without overwriting
the device tree settings and the device tree for devices using it
are updated with new parameters because the old ones are deprecated
by torvalds/linux@533af69.
A patch for kernel 5.4 is provided to support the new settings
because kernel 5.4 does not support it.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This backports a fix proposed for upstream kernel to fix overwriting
the NAND ECC engine in device tree.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
In the current state, nvmem cells are only detected on platform device.
To quickly fix the problem, we register the affected problematic driver
with the of_platform but that is more an hack than a real solution.
Backport from net-next the required patch so that nvmem can work also
with non-platform devices and rework our current patch.
Drop the mediatek and dsa workaround and rework the ath10k patches.
Rework every driver that use the of_get_mac_address api.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework patch 681-NET-add-mtd-mac-address-support to implement
only the function to read the mac-address from mtd.
Generalize mtd-mac-address-increment function so it can be applied
to any source of of_get_mac_address.
Rename any mtd-mac-address-increment to mac-address-increment.
Rename any mtd-mac-address-increment-byte to mac-address-increment-byte.
This should make simplify the conversion of target to nvmem implementation.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
sysupgrade metadata is not flashed to the device, so check-size
should be called _before_ adding metadata to the image.
While at it, do some obvious wrapping improvements.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
When the ltq_deu_vr9 kernel module is loaded, hostapd does not start any
more. It fails with this error message:
daemon.err hostapd: nl80211: kernel reports: key addition failed
daemon.err hostapd: Interface initialization failed
OpenWrt uses the standard Linux crypto API in the wifi drivers now
and this probably makes the system offload more crypto operations to
special hardware like the Lantiq DEU. There is probably a bug in the DEU
and these operations fail and then hostapd does not start the interface.
Do not include the Lantiq DEU by default any more.
Fixes: FS#3901
Fixes: 53b6783907 ("mac80211: remove patches stripping down crypto support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Notupus <notpp46@gmail.com>
Enable the XRX200 PMAC, GSWIP DSA tag and GSIP DSA drivers in the 5.4
kernel config. Update the existing vr9_*.dts{,i} to use the new
Ethernet and switch drivers. Drop the swconfig package from the xrx200
target because swconfig doesn't manage DSA based switches.
The new /etc/config/network format for the DSA driver is not compatible
with the old (swconfig) based one. Show a message during sysupgrade
notifying users about this change and asking them to start with a fresh
config (or forcefully update and then migrate the config manually).
Failsafe mode can now automatically bring up the first lan interface
based on board.json including DSA based setups. Drop
05_set_preinit_iface_lantiq from the xRX200 sub-target as this is not
needed anymore. For now we are keeping it for the ase, xway and
xway_legacy until there's some confirmation that it can be dropped from
there as well.
While here, some boards also receive minor fixups:
- Use LAN1 as LAN1 (according to a photo this port can also be
configured as WAN) on the Buffalo WBMR-300HPD. This makes it easier to
read the port mapping because otherwise we would have LAN{2,3,4} and
WAN (which was the case for the non-DSA version previously).
- vr9_avm_fritz3390.dts: move the "gpio" comment from port 0 and 1 to
their corresponding PHYs
- vr9_tplink_vr200.dtsi: move the "gpio" comment from port 0 to PHY 0
- vr9_tplink_tdw89x0.dtsi: move the "gpio" comment from port 0 to PHY 0
Acked-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Tested-by: Notupus <notpp46@googlemail.com> # TD-W9980/DM200/FRITZ 7430
Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on TDT VR2020
Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on TP-Link TD-W8980B
Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on ZyXEL P-2812HNU-F1
Tested-by: Daniel Kestrel <kestrel1974@t-online.de> # tested on Fritzbox 7490
Tested-by: Daniel Kestrel <kestrel1974@t-online.de> # tested on Fritzbox 3490
Tested-by: @jospezial <jospezial@gmx.de> # tested on VGV7510KW22 (o2 Box 6431)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Many people appear to use an unneeded "+" prefix for the increment
when calculating a MAC address with macaddr_add. Since this is not
required and used inconsistently [*], just remove it.
[*] As a funny side-fact, copy-pasting has led to almost all
hotplug.d files using the "+", while nearly all of the
02_network files are not using it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Removed upstreamed:
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
bcm63xx/patches-5.4/434-nand-brcmnand-fix-OOB-R-W-with-Hamming-ECC.patch*
Removed/code was included upstream and therefore redundant:
ramips/patches-5.4/999-fix-pci-init-mt7620.patch
All other patches automatically rebased.
* update_kernel.sh did not flag this yet it was included in 5.4.119[1], as a
result of the rebase, I removed my testing lines since I did not go back to
test built or to run test 5.4.119 with the removed patch present.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.4.119&id=e5b3e69eb36ac1178a7a2392616fd29afd288c4e
Signed-off-by: John Audia <graysky@archlinux.us>
ath79, lantiq, ipq40xx, ramips all use the OpenWrt-specific gpio-export
functionality. Consolidate the patch that adds it under hack-5.10 since
this logic is obviously not target-specific. For those who want to
disable it, unsetting CONFIG_GPIO_SYSFS symbol will disable this code.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
CONFIG_FORTIFY_SOURCE=y is already set in the generic kernel
configuration, but it is not working for MIPS on kernel 5.4, support for
MIPS was only added with kernel 5.5, other architectures like aarch64
support FORTIFY_SOURCE already since some time.
This patch adds support for FORTIFY_SOURCE to MIPS with kernel 5.4,
kernel 5.10 already supports this and needs no changes.
This backports one patch from kernel 5.5 and one fix from 5.8 to make
fortify source also work on our kernel 5.4.
The changes are not compatible with the
306-mips_mem_functions_performance.patch patch which was also removed
with kernel 5.10, probably because of the same problems. I think it is
not needed anyway as the compiler should automatically optimize the
calls to memset(), memcpy() and memmove() even when not explicitly
telling the compiler to use the build in variant.
This increases the size of an uncompressed kernel by less than 1 KB.
Acked-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Manually rebased*
generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch
Added new backport*
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
All others updated automatically.
The new backport was included based on this[1] upstream commit that will be
mainlined soon. This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
*Credit to Alexander Lobakin
1. https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=7ad18ff6449cbd6beb26b53128ddf56d2685aa93
Signed-off-by: John Audia <graysky@archlinux.us>
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Following changes are made to the Lantiq kernel patches:
0001-MIPS-lantiq-add-pcie-driver.patch
The pci header isn't included by the of_pci header any longer
0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch
Due to the merge of grx390 and ar10 clocks, extend support to grx390
0025-NET-MIPS-lantiq-adds-xrx200-legacy.patch
The do_carrier arguments was dropped from phy_link_change. The
phylib has always sets the third parameter to true so the flag is
always changed anyway.
of_get_phy_mode() returns an error, or 0 on success, and pass a
pointer, of type phy_interface_t, where the phy mode should be
stored now. So far an error wasn't considered. Print at least an
error message if something unexpected happens.
The stuck queue is now passed to xrx200_tx_timeout (the timeout
handler) but not used so far.
0028-NET-lantiq-various-etop-fixes.patch
ioremap has provided non-cached semantics by default since the Linux
2.6 days and was removed with kernel version 5.6.
of_get_phy_mode() returns an error, or 0 on success, and pass a
pointer, of type phy_interface_t, where the phy mode should be
stored now. So far an error wasn't considered. Print at least an
error message if something unexpected happens.
0042-arch-mips-increase-io_space_limit.patch
Move IO space extension to laniq specific file
Signed-off-by: Mathias Kresin <dev@kresin.me>
Duplicate kernel 5.4 config and patches for kernel 5.10.
Duplicate the devicetree source files as well, they need kernel 5.10
specific adjustments.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the device_type property to mark PCI host bridges as such. With
linux 5.10 it is mandatory, otherwise the PCI IO space is flages as PCI
memory and the PCI init fails.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The FRITZ!Box 3390 actually contains two SoCs, one Lantiq with a
5GHz WiFi and one AR9342 with a 2.4GHz WiFi. Only the Lantiq
has access to the flash memory, the Atheros runs fully from RAM.
Specifications
--------------
- Lantiq 500 MHz
- 128MiB RAM
- 128MiB NAND
- 256k Flash
- AR9580 5GHz WiFi
- AR9342 560 MHz
- 64MiB RAM
- AR9328 2.4GHz WiFi
Remarks
-------
This commit only adds support for the Lantiq side of things and
prepares the drivers for communication with the Atheros SoC. Thus,
only 5GHz WiFi works by default, the 2.4GHz WiFi will be added via
another target.
Some kernel patches will be required to add support for the Atheros SoC.
Installation
------------
Use the eva_ramboot.py script to boot the initramfs image. Then, transfer
the sysupgrade image to the device and run sysupgrade to flash it to the
NAND.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Acked-by: Aleksander Jan Bajkowski A.Bajkowski@stud.elka.pw.edu.pl
Signed-off-by: Joachim Cerny <cocktail_yogi@web.de>
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Some users report that current snapshot producies non-bootable images.
Stock uboot can boot images if the kernel is smaller than 2MB.
Set maximum kernel size and disable image building for this board.
Ref: https://forum.openwrt.org/t/astoria-arv7519rw22-bootloops-after-upgrade/89843
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
It's meant to provide upstream support for mtd & NVMEM. It's required
e.g. for reading MAC address from mtd partition content. It seems to be
in a final shape so it's worth testing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
5.4.102 backported a lot of stuff that our WireGuard backport already
did, in addition to other patches we had, so those patches were
removed from that part of the series. In the process other patches were
refreshed or reworked to account for upstream changes.
This commit involved `update_kernel.sh -v -u 5.4`.
Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This adds the latest version of ofpart commit. It hopefully
1. Doesn't break compilation
2. Doesn't break partitioning
(this time).
It's required to implement fixed partitioning with some quirks. It's
required by bcm53xx, bcm4908, kirkwood, lantiq and mvebu.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Assign the usbdev trigger via devicetree and drop the userspace
handling of the usb leds.
Drop the now unused userspace helper code as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These boards have a fixed size kernel partition but do not limit the
kernel size during image building.
Disable image building for both boards as well, since the kernel of the
last release as well as master are to big to fit into the 2 MByte kernel
partition.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Assign the usbdev trigger via devicetree and drop the userspace
handling of the usb leds
Add the PCI attached usb controller as trigger sources for the usb led
as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The USB ports if a FRIZZ!Box 7320 do not supply power to connected
devices.
Add the GPIOs enabling USB power as regulator, to enable USB power
supply as soon as the USB driver is loaded.
Fixes FS#3624
Signed-off-by: Mathias Kresin <dev@kresin.me>
FRITZ!Box 7412 loads the firmware for fast ethernet PHY and mii is
more accurate in this case.
Gmii is used by Gigabit ethernet PHYs.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Reviewed-by: Mathias Kresin <dev@kresin.me>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops the shebang from another bunch of files in various /lib
folders, as these are sourced and the shebang is useless.
Fix execute bit in one case, too.
This should cover almost all trivial cases now, i.e. where /lib is
actually used for library files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The following four led triggers are enabled in generic config.
* kmod-ledtrig-default-on
* kmod-ledtrig-heartbeat
* kmod-ledtrig-netdev
* kmod-ledtrig-timer
Drop the packages and remove them from DEVICE_PACKAGES.
There's no other package depending on them in this repo.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Those targets have already enabled some other LED triggers, so enabling
a few more won't be a big problem.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The heartbeat trigger is used by luci-mod-system, which is installed
as a part of the standard luci package set. It seems the LED trigger
will be required quite often, so let's enable it by default.
This increases uncompressed kernel size by about 100 bytes on ath79/generic.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
These parameters are the same as in vr9.dtsi. This patch removes
redundant parameters.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
The sub target does not support network and there are not so many users
out there, just mark it as source only, so we do jot have to build it.
The quality is not worse than before, it just does not make much sense
to build this automatically.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes build of squashfs image on lantiq. Currently the FEATURE
variable is overwritten by the subtarget.
Fixes: FS#3480
Fixes: f1c6523376 ("lantiq: clean up target/subtarget features")
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[reformat Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The feature "squashfs" is defined for target and all subtargets
individually. Remove the redundant entries in the subtargets.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[split patch, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware:
- SoC: Lantiq VRX 220
- CPU: 2x MIPS 34Kc 500 MHz
- RAM: 128 MiB 250 MHz
- Flash: 128 MiB NAND
- Ethernet: Built-in Fast Ethernet switch, 4 ports used
- Wifi: Atheros AR9381-AL1A b/g/n with 2 pcb/internal and 1 external antennas
- USB: 1x USB 2.0
- DSL: Built-in A/VDSL2 modem
- DECT: Dialog SC14441
- LEDs: 1 two-color, 4 one-color
- Buttons: 1x DECT, 1x WIFI
- Telephone connectors: 1 FXS port via TAE or RJ11 connector
With the exception of FXS/DECT everything works
(there are no drivers for AVM's FXS or DECT implementation),
DSL is yet untested.
Installation:
Boot up the device and wait a few seconds. Run the eva_ramboot.py script
in scripts/flashing/ to load the initramfs image on the device:
$ ./scripts/flashing/eva_ramboot.py 192.168.178.1 <path to your initramfs image>
If the script fails to reach the device, maybe try 169.254.120.1.
Wait until booting is complete. You should now be able to reach your device
under the default ip address 192.168.1.1.
Before flashing, check if linux_fs_start is not set to 1 in the tffs partition:
$ fritz_tffs_nand -d /dev/mtd1 -n linux_fs_start
If linux_fs_start is 1, you will need to reset it to 0, either by FTP,
upgrading FritzOS or doing a recovery.
Now you should be able to flash the device using sysupgrade.
Signed-off-by: Leon Maurice Adam <leon.adam@aol.de>
Acked-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[drop BOARD_NAME, use wpad-basic-wolfssl, drop 4.19, drop dts-v1,
remove model prefix from LED names]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The target uses 5.4 as default kernel since 06/2020.
Kernel 4.19 support is not really maintained anymore, it does not
seem to be needed and upcoming changes (mainly DSA) will break
backward-compatibility anyway.
Thus, make maintaining of old stuff and reviewing of new stuff
easier by removing support for kernel 4.19.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like in the previous patches for other targets, this will remove
the "devicename" from LED labels in lantiq.
The devicename is removed in DTS files and 01_leds, consolidation
of definitions into DTSI files is done where (easily) possible,
and migration scripts are updated. The DTS/DTSI consolidation is
only performed for files-5.4.
For lantiq,easy98020 some LED definitions have the form
"devicename:function" without the color, so we need to implement
explicit migration for that one.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Seemingly unneeded based on new upstream code so manually deleted:
layerscape:
820-usb-0007-usb-dwc3-gadget-increase-timeout-value-for-send-ep-c.patch
Manually merged:
generic-hack:
251-sound_kconfig.patch
All other modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add lantiq test report, minor commit message clarification]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
In lantiq, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent SoC-based DTSI files already determines the DTS
version, so putting it into the DTS files is just a useless repetition.
Consequently, this patch puts the dts-v1 statement into the top-level
SoC-based DTSI files, and removes all other occurences.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes accordingly where necessary.
Changes are applied to files-5.4 only, files-4.19 remains untouched.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x, lantiq/xrx200 and ath79/generic
Run-tested: ipq806x (R7800), lantiq (Easybox 904 xDSL)
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add test on lantiq]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is the most popular choice in the linux kernel tree.
Within OpenWrt, this change will establish consistency with ath79
and ramips targets.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[extend commit message, include netgear_dm200, update base-files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As described in commit commit 891a700759 ("lantiq: enable second VPE
on Fritz!Box 7412"):
The AVM Fritz!Box 7412 does not use the VMMC part of the Lantiq chip but
rather a proprietary solution based on the DECT chip for the FXS ports.
We can remove last traces of vmmc in dts.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
In order to support SAE/WPA3-Personal in default images. Replace almost
all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for
consistency. Keep out ar71xx from the list as it won't be in the next
release and would only make backports harder.
Build-tested (build-bot settings):
ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway,
sunxi: a53
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This PR is a blend of several kernel bumps authored by ldir taken from his
staging tree w/ some further adjustments made by me and update_kernel.sh
Summary:
Deleted upstreamed patches:
generic:
742-v5.5-net-sfp-add-support-for-module-quirks.patch
743-v5.5-net-sfp-add-some-quirks-for-GPON-modules.patch
bcm63xx:
022-v5.8-mtd-rawnand-brcmnand-correctly-verify-erased-pages.patch
024-v5.8-mtd-rawnand-brcmnand-fix-CS0-layout.patch
mediatek:
0402-net-ethernet-mtk_eth_soc-Always-call-mtk_gmac0_rgmii.patch
Deleted patches applied differently upstream:
generic:
641-sch_cake-fix-IP-protocol-handling-in-the-presence-of.patch
Manually merged patches:
generic:
395-v5.8-net-sch_cake-Take-advantage-of-skb-hash-where-appropriate.patch
bcm27xx:
950-0132-lan78xx-Debounce-link-events-to-minimize-poll-storm.patch
layerscape:
701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch
Build system: x86_64
Build-tested: ath79/generic, bcm27xx/bcm2708, bcm27xx/bcm2711,
imx6, mvebu/cortexa9, sunxi/a53
Run-tested: Netgear R7800 (ipq806x)
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-By: Lucian Cristian <Lucian.cristian@gmail.com> [mvebu]
Tested-By: Curtis Deptuck <curtdept@me.com> [x86/64]
[do not remove 395-v5.8-net-sch_cake-Take-advantage-... patch,
adjust and refresh patches, adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-By: John Audia <graysky@archlinux.us> [ipq806x]
It has been decided that the 19.07 release will be last one to include
4/32 devices.
This disables default build for all devices with 4M flash on lantiq.
Note that this will affect _all_ devices for amazonse ("ase") and
xway_legacy subtarget.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes a few cosmetic issues with partition offset and size
that are inconsistent probably due to copy/pasting.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
xrx200 has a 6 port built-in switch with 2 integrated PHY. None of the
xrx200 router uses external switch. Most boards use integrated or Lantiq
(Intel) PEF7071 PHY. Only some FritzBox routers use AT803X PHY and
VGV7510KW22 use ICPLUS PHY. Other unused PHY drivers may be removed.
This patch enables these symbols only on xway and xway_legacy subtargets:
- CONFIG_PSB6970_PHY (Driver for PHY in PSB6970 - 7 port FE Switch)
- CONFIG_RTL8366RB_PHY (Driver for PHY in RTL8366 - 6 port GE Switch)
- CONFIG_RTL8366_SMI (Driver for RTL8366 - 6 port GE Switch)
Reduces image size by 7.3kB.
Continuation of 58a6f06978 (PR: #2983)
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[fix sorting in config files, small fix in commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes a warning in the SPI driver at bootup. This warning is seen
in kernel 5.4 on lantiq deives.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Pressing the 'WLAN' button should enable/disable wireless activity.
Currently, the button is mapped to the KEY_WLAN, which will not
have this effect.
This patch changes the mapping of the WLAN button, so a button
press will emit an action for the 'rfkill' key instead of 'wlan'.
Apparently, this is what stock OpenWRT expects.
This fix is analogous to the preceding patch for Fritzbox 3370.
Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
The WLAN button actions are reversed, i.e. pressing the button emits a
'released' action, and vice versa.
This can easily be checked by adding
logger -t button_action "$BUTTON $ACTION"
as the second line of /etc/rc.button/rfkill, and using logread to read
the events (assuming the preceding patch has been applied).
Defining the GPIO as ACTIVE_LOW corrects this behavior.
Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
Pressing the 'WLAN' button should enable/disable wireless activity.
However, on the Fritzbox 3370 this doesn't have an effect.
This patch changes the mapping of the physical WLAN button, so a button
press will emit an action for the 'rfkill' key instead of 'wlan'.
Apparently, this is what stock OpenWRT expects, and also what is
implemented for most other devices.
Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
Split the /etc/uci-defaults/01_led_migration scripts into subtargets
as already done for most of the other base-files.
While this introduces a minor amount of code duplication, it still
is considered an improvement, as device-specific settings are kept
together in the subtargets' base-files and the script at hand can be
removed entirely for two of the subtargets not needing it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It does not make sense to install this components on lantiq systems
where the dsl subsystem is not needed/used.
This also makes it possible to use the files also on other targets.
(hopefully ipq401x / FritzBox 7530 in the near future)
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
This fixes the gphy LED pins for Zyxel P-2812 devices. The have
been accidentally altered during a tidy-up operation (see Fixes:
below).
No ports were available, dmesg reported:
[ 0.658577] pinctrl-xway 1e100b10.pinmux: pin io5 already requested by
1e100bb0.stp; cannot claim for 1e108000.eth
[ 0.667566] pinctrl-xway 1e100b10.pinmux: pin-5 (1e108000.eth) status -22
[ 0.685238] lantiq,xrx200-net 1e108000.eth: Error applying setting,
reverse things back
[ 0.693270] lantiq,xrx200-net: probe of 1e108000.eth failed with error -22
Fixes: FS#3188
Fixes: 660200e53d ("lantiq: dts: assign the GPHY LED pins to the
Ethernet controller node")
Suggested-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Willem van den Akker <wvdakker@wilsoft.nl>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit e53ec043ba ("kirkwood: move usb support to modules") has moved
this config symbol into generic configs, so it could be removed from
other configs.
Suggested-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fix inconsistencies found in DTS files and sort ethernet ports based on
updated names.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[squash two separate patches, rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The removed lines are already included in vr9_avm_fritz736x.dtsi
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move the USB VBUS regulator nodes out of the GPIO controller node. This
fixes a problem where the "regulator-fixed" driver wasn't probed for
these regulators because the GPIO driver doesn't scan the child-nodes
and based on the dt-bindings documentation it's not supposed to.
This fixed the following error reported by Luca Olivetti:
...
dwc2 1e101000.usb: DWC OTG Controller
dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
dwc2 1e101000.usb: irq 62, io mem 0x1e101000
dwc2 1e101000.usb: startup error -517
dwc2 1e101000.usb: USB bus 1 deregistered
dwc2 1e101000.usb: dwc2_hcd_init() FAILED, returning -517
Fixes: FS#1634
Cc: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Add missing switch config (4 LAN-Ports + CPU).
Grey WAN port (used for ADSL) is not part of the switch.
Signed-off-by: Lars Wessels <software@bytebox.org>
[rework commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Set wifi mac from flash partition 'board_config' to
match the label on the device (Easybox 802).
Currently the wifi mac is always set to 00:0c:43:28:60:00.
eth0 and WiFi will now share the same mac (as in original firmware).
Signed-off-by: Lars Wessels <software@bytebox.org>
[improve commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Fixes:
- CVE-2020-10757
The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.
Run tested: ath79
Build tested: ath79
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All boards on xrx200 use builtin switch and there is no supported device
with external switch.
It was copy paste from xway subtarget and was added in commit 18b76c66fb.
Save 20.3 kB flash memory.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.
The previous patch in 36f628910b was only applied to the 4.19 file,
so let's just make it consistent with this patch.
Cc: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CONFIG_HZ_100 is not set to "y" in generic config anymore since
3a761c90af ("treewide: Don't diverge from upstream default HZ
settings on 4.19"), so we don't need to disable it anymore either.
This was the only remaining case in the entire tree.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The additional supported device isn't required since this is a new
device. Some board contains an addtional device,
those device were supported in earlier versions which used the
"old" image builder code.
To support an sysupgrade from such old version, there is the all caps
additional device.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Use similiar naming scheme as ath79.
Since the fritz 7360 v2 was only in the tree for 2 days, there
is no compatibility for the old image.
Users which has installed the fritz 7360 v2 before this change, must
use sysupgrade --force to skip checks on the board.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops some ancient kernel version switches from patches on
lantiq target. The patch only adjusts the latest kernel 5.4, as
doing it a second time for an older kernel seems a waste of time
for a cosmetic change.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the Fritzbox 7360v2
CPU: VR9 500MHz Cores: 2
RAM: 128 MB
NOR-Flash: 32 MB
WLAN: AR9287-BL1A
DECT is not working.
Thanks Sebastian Ortwein for adding 7360SL.
The dts file is derived from avm_fritz7360sl.dts.
Firmware can be flashed with this method:
1.) Set your client IP to 192.168.178.2
2.) Power on your your Fritzbox and connect to 192.168.178.1
via ftp in the first 5 seconds.
3.) login with adam2/adam2
4.) type into the ftp prompt:
passive
binary
debug 1
quote MEDIA FLSH // (not FLASH)
put openwrt-lantiq-xrx200-avm_fritz7360v2-squashfs-sysupgrade.bin mtd1
// using the correct location for the squashfs-sysupgrade-firmware.bin
5.) wait till red light flashing turns off.
6.) type: exit
Run tested with kernel 4.19 and 5.4 on Fritzbox 7360 V2.
Issue:
Ethernet speed is slow, (iperf between a Xiaomi mir3g
and this router results in <80Mbits throughput
with a wired cable when using the gbit ports.)
Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.
For ramips, remove redundant values already present in parent file.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
We do not build images with a jffs2 rootfs, but jffs2 is still used as
filesystem for the rootfs_data.
Fixes: e3eaf57808 ("lantiq: kernel 5.4: debloat kernel config")
Signed-off-by: Mathias Kresin <dev@kresin.me>
The etop driver is used by all targets except xrx200.
Remove the UBIFS compression support for zlib and zstd from the xway
subtarget. The hardware is EOL for a long time and it's unlikely to ever
see a board shipped with an UBIFS using these compression methods.
Remove the JFFS2 support. Support for jjfs2 images was dropped years
ago.
It shrinks the compressed kernel up to 130 KByte.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Switch to the mainline Lantiq PCIe PHY driver and update the vr9.dtsi
accordingly.
The Lantiq IRQ SMP support added upstream required changes to the SoC
dtsi as well.
Following changes are made to the Lantiq kernel patches:
0005-lantiq_etop-pass-struct-device-to-DMA-API-functions.patch
0006-MIPS-lantiq-pass-struct-device-to-DMA-API-functions.patch
applied upstream
0008-MIPS-lantiq-backport-old-timer-code.patch
access_ok API update because it lost it's type (which was the first)
parameter in upstream commit 96d4f267e40f95 ("Remove 'type' argument
from access_ok() function")
0024-MIPS-lantiq-autoselect-soc-rev-matching-fw.patch
merged into 0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch
0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch
revert upstream changes required for upstream xrx200 ethernet and
xrx200 (DSA) switch driver but breaking our driver
0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch
required for our driver but dropped upstream, add former upstream
version
0028-NET-lantiq-various-etop-fixes.patch
now has to use the phy_set_max_speed API instead of modifying
phydev->supported. Also call ltq_dma_enable_irq() in
ltq_etop_open() based on upstream commit cc973aecf0b054 ("MIPS:
lantiq: Do not enable IRQs in dma open")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This is referenced in two .dts but never actually used from userspace.
Drop support for this property because it's not used and because it
makes updating to Linux 5.4 harder (as the patch doesn't apply anymore).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
