Avoid shipping ath10k board file in Mikrotik initram images
Most will only ever need to use these initram images once—to initially
load OpenWrt, but fix these images for more consistent Wi-Fi performance
between the initram and installed squashfs images.
OpenWrt BUILDBOT config ignores -cut packages in the initram images build.
This results in BUILDBOT initram images including the linux-firmware
qca4019 board-2.bin, and (initram image booted) Mikrotik devices loading
a generic BDF, rather than the intended BDF data loaded
from NOR as an api 1 board_file.
buildbot snapshot booted as initram image:
cat /etc/openwrt_version
r19679-810eac8c7f
dmesg | grep ath10k | grep -E board\|BDF
[ 9.794556] ath10k_ahb a000000.wifi: Loading BDF type 0
[ 9.807192] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:16
crc32 11892f9b
[ 12.457105] ath10k_ahb a800000.wifi: Loading BDF type 0
[ 12.464945] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:17
crc32 11892f9b
CC: Robert Marko <robimarko@gmail.com>
Fixes: 5eee67a72f ("ipq40xx: mikrotik: dont include ath10k-board-qca4019 by default")
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Reviewed-by: Robert Marko <robimarko@gmail.com>
ucidef_set_bridge_device is needed for DGND3700v2 network config since VLAN 1
must be used for the switch to be correctly configured.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Patches to support the SoC's GPIO controller for RTL930x and RTL931x
devices have been accepted upstream. Replace the current preliminary
patch with the upstream ones, excluding devictree binding changes.
The updated patches add GPIO IRQ balancing support on RTL930x, but this
cannot be used until these devices also support SMP.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Update the name of for the Ubiquiti NanoBeam M5 to match the
auto-generated one at runtime. Otherwise sysupgrade complains about
mismatching device names.
This also required renaming the DTS.
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Ubiquiti NanoBeam M5 devices are CPE equipment for customer locations
with one Ethernet port and a 5 GHz 300Mbps wireless interface.
Specificatons:
- Atheros AR9342
- 535 MHz CPU
- 64 MB RAM
- 8 MB Flash
- 1x 10/100 Mbps Ethernet with passive PoE input (24 V)
- 6 LEDs of which four are rssi
- 1 reset button
- UART (4-pin) header on PCB
Notes:
The device was supported by OpenWrt in ar71xx.
Flash instructions (web/ssh/tftp):
Loading the image via ssh vias a stock firmware prior "AirOS 5.6".
Downgrading stock is possible.
* Flashing is possible via AirOS software update page:
The "factory" ROM image is recognized as non-native and then installed correctly.
AirOS warns to better be familiar with the recovery procedure.
* Flashing can be done via ssh, which is becoming difficult due to legacy
keyexchange methods.
This is an exempary ssh-config:
KexAlgorithms +diffie-hellman-group1-sha1
HostKeyAlgorithms ssh-rsa
PubkeyAcceptedKeyTypes ssh-rsa
User ubnt
The password is ubnt.
Connecting via IPv6 link local worked best for me.
1. scp the factory image to /tmp
2. fwupdate.real -m /tmp/firmware_image_file.bin -d
* Alternatively tftp is possible:
1. Configure PC with static IP 192.168.1.2/24.
2. Enter the rescue mode. Power off the device, push the reset button on
the device (or the PoE) and keep it pressed.
Power on the device, while still pushing the reset button.
3. When all the leds blink at the same time, release the reset button.
4. Upload the firmware image file via TFTP:
tftp 192.168.1.20
tftp> bin
tftp> trace
Packet tracing on.
tftp> put firmware_image.bin
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
The MikroTik hAP (product code RB951Ui-2nD) is
an indoor 2.4Ghz AP with a 2 dBi integrated antenna built around the
Atheros QCA9531 SoC.
Specifications:
- SoC: Atheros QCA9531
- RAM: 64 MB
- Storage: 16 MB NOR - Winbond 25Q128FVSG
- Wireless: Atheros QCA9530 (SoC) 802.11b/g/n 2x2
- Ethernet: Atheros AR934X switch, 5x 10/100 ports,
10-28 V passive PoE in port 1, 500 mA PoE out on port 5
- 8 user-controllable LEDs:
· 1x power (green)
· 1x user (green)
· 4x LAN status (green)
· 1x WAN status (green)
· 1x PoE power status (red)
See https://mikrotik.com/product/RB951Ui-2nD for more details.
Notes:
The device was already supported in the ar71xx target.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Maciej Krüger <mkg20001@gmail.com>
The MikroTik RB952Ui-5ac2nD (sold as hAP ac lite) is an indoor 2.4Ghz
and 5GHz AP/router with a 2 dBi integrated antenna.
See https://mikrotik.com/product/RB952Ui-5ac2nD for more details.
Specifications:
- SoC: QCA9533
- RAM: 64MB
- Storage: 16MB NOR
- Wireless: QCA9533 802.11b/g/n 2x2 / QCA9887 802.11a/n/ac 2x2
- Ethernet: AR934X switch, 5x 10/100 ports,
10-28 V passive PoE in port 1, 500 mA PoE out on port 5
- 6 user-controllable LEDs:
- 1x user (green)
- 5x port status (green)
Flashing:
TFTP boot initramfs image and then perform sysupgrade. The "Internet"
port (port number 1) must be used to upload the TFTP image, then
connect to any other port to access the OpenWRT system.
Follow common MikroTik procedure as in
https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
A devent amount of patches have been upstreamed, so maintaining linux 5.10 on
this target makes no sense.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Use the same order for /etc/board.d/02_network and
/lib/preinit/05_set_preinit_iface_brcm2708.
- Add missing RPi 400 and CM4 to /lib/preinit/05_set_preinit_iface_brcm2708.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Since MikroTik subtarget now uses dynamic BDF loading its crucial that it
doesnt include the board-2.bin at all which is provided by the
ath10k-board-qca4019 package.
So to resolve this dont include the ath10k-board-qca4019 package on the
MikroTik subtarget.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since we now provide the BDF-s for MikroTik IPQ40xx devices on the fly,
there is noneed to include package and ship them like we do now.
This also resolves the performance issues that happen as MikroTik
changes the boards and ships them under the same revision but they
actually ship with and require a different BDF.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since we now can pass the API 1 BDF-s aka board.bin to the ath10k
driver per radio lets use that to provide the BDF-s for MikroTik devices.
This also resolves the performance issues that happen as MikroTik changes
the boards and ships them under the same revision but they actually ship
with and require a different BDF.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove redundant target-level entries, noting that these settings will be
configured from "Kernel build options" of Kconfig.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[remove from new configs introduced after patch submission]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add DEBUG_INFO_REDUCED as a kernel config option and remove it from the
kernel configs. This is in preparation of the upcoming option to enable
BTF typeinfo, which is incompatible with DEBUG_INFO_REDUCED.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
We currently enable DEBUG_INFO_REDUCED for all targets via the generic
kernel config. There is only one subtarget, layerscape/armv8_64b, that
overrides this setting. As there is no explanation for this in the
commit message that introduced this, and question to its author went
unanswered, let's simply drop this symbol from the subtarget config.
This way, we have consistency across the tree, and we do not have to
introduce a special case when moving this symbol to an OpenWrt kernel
config option.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Building tools/resolve_btfids requires libelf and zlib. Without this
build fix, the kernel build system will not find these dependencies.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This backports a patch from Linux 5.10.116 to fix a compile problem
introduced in 5.10.114.
drivers/usb/phy/phy-generic.c could not find
devm_regulator_get_exclusive().
Fixes: 8592df67f4 ("kernel: bump 5.10 to 5.10.114")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold
under different brands (among others, A1 Telekom Austria SmartHome Premium
Gateway). It has multi-protocol radio support in addition to LAN and WiFi.
Note: BLE and audio are currently unsupported.
Specifications
--------------
- MT7621ST 880MHz, Single-Core, Dual-Thread
- MT7603EN 2.4GHz WiFi
- MT7662EN 5GHz WiFi + BLE
- 128MiB NAND
- 256MiB DDR3 RAM
- SD3503 ZWave Controller
- EM357 Zigbee Coordinator
- Telit UMTS module
- Rechargeable battery
- speaker and microphone
MAC address assignment
----------------------
LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches
the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the
OEM firmware does not enable 5GHz WiFi.
Installation
------------
Attach serial console, then boot the initramfs image via TFTP.
Once inside OpenWrt, run sysupgrade -n with the sysupgrade file.
Attention: The device has a dual-firmware design. We overwrite kernel2,
since kernel1 contains an automatic recovery image.
If you get NAND ECC errors and are stuck with bad eraseblocks, try to
erase the mtd partition first with
mtd unlock ubi
mtd erase ubi
This should only be needed once.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
this adds the mediatek,led_source dts binding for
Asus RT-AC1200 devices' dtsi, for correct switch LED
behavior.
The dts-binding is introduced in commit:
65dc9e0980
Without this, we only have constantly very fast
blinking LEDs, which don't react on any traffic or
LAN events at all.
Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC in
contrast to the Macronix NAND with 4 bit ECC. This removes the hardcoded
ECC strength and step size as set in qcom-ipq4019.dtsi, thus relying on the
kernel NAND detection routines to correclty set up the ECC parameters.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
The Toshiba TC58NVG0S3HTA00 is detected with 64 byte OOB while the flash
has 128 byte OOB. This adds a static NAND ID entry to correct this.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
ZTE MF286A and MF286R feature a "power switch override" GPIO in stock
firmware as means to prevent power interruption during firmware update,
especially when used with internal battery.
To ensure that this GPIO is
properly driven as in stock firmware, configure it with userspace GPIO
switch.
It was observed that on some units, the modem would not be
restarted together with the board itself on reboot, this should help
with that as well.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
On GL-AR300M Series GPIO17 described as I2C SDA in Device Tree.
Because of GPIO_OUT_FUNCTION4 register was not initialized on start,
GPIO17 was uncontrollable, it always in high state. According to QCA9531
documentation, default setting of GPIO17 is SYS_RST_L. In order to make
GPIO17 controllable, it should write value 0x00 on bits [15:8] of
GPIO_OUT_FUNCTION4 register, located at 0x1804003C address.
Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
All Freescale processors used in this target are capable to detect error
and correction. [1] It can not be used as kernel module. [2] This is
helpful to report hardware errors.
It enables three kernel options:
- EDAC, which is a subsystem
- EDAC_LEGACY_SYSFS, it enables sysfq nodes
- MP85XX, support for Freescale MPC8349, MPC8560, MPC8540, MPC8548, T4240
EDAC is already enabled for following targets:
qoriq, octeon, octeontx and zynq.
[1] https://cateee.net/lkddb/web-lkddb/EDAC.html
[2] https://patchwork.ozlabs.org/patch/554908/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This makes it possible to fix Netgear WNDAP620+660 DTS ugliness.
Bring back the dtb and firmware partitions for the WNDR4700.
Thank you, mans0n.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.
Fixes: #9824
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Do not reset the RTL930x SerDes on link changes, instead set up
the SDS with internal PHYs for the SFP+ ports only.
This fixes the 8 1GBit ports on the Zyxel XGS1250 which
do not work without this patch.
A complete SerDes reset was performed on all SerDes links. For copper
1Gbit ports, this is commonly a single XGMII link to an RTL8218D. There
is however no support for setting up the XGMII link on RTL9300/RTL9310,
thereby wiping the (RX/TX) setup done by u-boot and breaking the 1GBit
ports. No SerDes reset should be done for these links.
The handling of SGMII/HiSGMII, 1000BX or 10GR links is actually entirely
different. All these modes need to be suitably RX calibrated and the
pre- main and post- amplifiers set up properly for TX.
The 10GBit SFP+ fiber links are recalibrated instead of reset, which
e.g. is necessary when someone pulls a module out and puts another in.
This makes swapping out 10GBit fiber modules possible. 1GBit modules are
not yet supported, nor any modules with an internal phy.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
[rewrite commit message based on discussion]
Link: http://lists.infradead.org/pipermail/openwrt-devel/2022-May/038623.html
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Specifications:
SoC: MediaTek MT7621
RAM: 256 MB
Flash: 32 MB
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0
Buttons: Reset, WPS
LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
Power: DC 12V 1A tip positive
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
Loads only signed manufacture firmware due to bootloader RSA verification
serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
connect to any lan ethernet port
power on the device while holding the reset button
wait at least 8 seconds before releasing reset button for image to
download
Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com>
[ensure unique wireless MAC, fix GPIO pingroup]
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes a bug where frames sent to the switch itself were
flooded to all ports unless the MAC address of the CPU-port
was learned otherwise.
Tested-by: Wenli Looi <wlooi@ucalgary.ca>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
[fix code formatting]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The ZyXEL GS1900-16 is a 16 port gigabit switch similar to other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-16
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8HE
* Ethernet: 16x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
16 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J12) with populated standard pin connector on
the right back of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
file amd select open so File Path is update with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-16 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Raylynn Knight <rayknight@me.com>
[removed duplicate patch title, align RAM specification]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This workaround will allow the MA5671A to function, ignoring the
persistently asserted tx-fault.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
(added 5.15 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch copies over refreshed config and patches from 5.10
with the following changes:
- dropped superfluous tc654/tc655 variant detection patch
(tc654 support will become available upstream starting with
5.17-rc7+).
- dropped xhci msi(x) workaround... as the broken MSI(X)
is now gone.
- dropped dwc2 workaround since the driver was fixed and it
works without it.
Please note: Netgear WNDAP660 & WNDAP620 users:
Due to the kernel's size increase, uboot will likely break
because it is overwrite the kernel during decompression.
To fix this (and debrick affected devices, no reflash
necessary), attach the RJ45-Serial-Console cable and
enter the following in the uboot prompt during bootup:
setenv kernel_addr_r 1100000
saveenv
run bootcmd
to restore the old/previous behavior:
setenv kernel_addr_r 600000
saveenv
run bootcmd
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
upstream linux have these watchdogs locked behind X86.
These will not build on other architectures. So move them
to target/linux/x86/modules.mk
drivers/watchdog/Kconfig:
|config F71808E_WDT
| tristate "Fintek F718xx, F818xx Super I/O Watchdog"
| depends on X86
|[...]
|config IT87_WDT
| tristate "IT87 Watchdog Timer"
| depends on X86
|[...]
|config ITCO_WDT
| tristate "Intel TCO Timer/Watchdog"
| depends on (X86 || IA64) && PCI
|[...]
|config W83627HF_WDT
| tristate "Watchdog timer for W83627HF/W83627DHG and compatibles"
| depends on X86
|[...]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Grommish reported the dreaded build error that happend with 5.4
since the kernel didn't have the cgpio v2 interface. His reason
for the removed 5.4 was that the octeon target had a memory leak
issue, so he had to backport the removed 5.4 kernel for his tests.
Chen Minqiang chimed in and noted that no matter what (i.e.
@TARGET_x86 in depends) didn't prevent the package from being build
on other targets.
From what I can tell, the reason for this was that +nu801 meant
that kmod-meraki-mx100 pulled in an unconditional dependency as
part of to the kernel build.
|scripts/package-metadata.pl mk tmp/.packageinfo
|
|$(curdir)/kernel/linux/compile += $(curdir)/firmware/linux-firmware/compile \
| $(curdir)/firmware/prism54-firmware/compile \
| $(curdir)/kernel/gpio-button-hotplug/compile \
| >>> $(curdir)/system/gpio-cdev/nu801/compile <<<
change this by making the dependency conditional on the
meraki-mx100 module itself. Note that the nu801 enables/sets
the KCONFIG for the cgpio v2 interface itself, since the
userspace program and not the kernel meraki-mx100 relies on it.
Reference: <https://github.com/openwrt/openwrt/commit/eeb8fd4ce7e9>
Reported-by: Grommish <grommish@gmail.com>
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
QEMU+Libvirt can emulate the ib700wdt watchdogs
which due to its I/O-Port mapping makes it x86
specific.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
QEMU can emulate several watchdogs:
aspeed SoC, i6300esb, ib700wdt, imx2, cmsdk-apb and sbsa_gwdt.
Out of these, the ARM SBSA Generic Watchdog (sbsa_gwdt)
makes the most sense for the armvirt' 64 target. Both imx2 and
aspeed are guarded by special vendor specific CONFIG_ in the
upstream kernel.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Commit f4fb63d2ab ("ipq40xx: 5.10: move AR40xx to MDIO drivers") moved
the ar40xx driver files to kernel version specific directories to place
them in different subdirectory in kernel tree. But now kernel 5.4 is
gone and there is no reason to keep them separate. Move them back to
common files/ directory.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Also apply commit ab7e53e5cc ("ipq40xx: 5.10: fix ar40xx driver") to
5.15 driver.
The commit fixes the data corruption on TX packets. Packets are
transmitted, but their contents are replaced with zeros. This error is
caused by the lack of guard (50 ms) intervals between calibration phases.
This error is treated by adding mdelay(50) to the calibration function
code. In the original qca-ssda code, these mdelays were existing, but in
the ar41xx.c they are gone.
Fixes: 87318eb179 ("ipq40xx: 5:15: copy config and patch from 5.10")
Signed-off-by: Nick Hainke <vincent@systemli.org>
According wiki https://docs.gl-inet.com/en/2/hardware/mt300n-v2/
GL-MT300N-V2 have I2C interface on GPIO4, GPIO5.
Adding I2C in device tree make possible using I2C on this device.
Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
Hardware specs:
SoC: Qualcomm IPQ8065 (dual core Cortex-A15)
RAM: 512 MB DDR3
Flash: 256 MB NAND, 32 MB NOR
WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz
Switch: QCA8337
Ethernet: 5x 10/100/1000 Mbit/s
USB: 1x USB 3.0 Type-A
Buttons: WPS, Reset
Power: 12 VDC, 2.5 A
Ethernet ports:
1x WAN: connected to eth2
4x LAN: connected via the switch to eth0 and eth1
(eth0 is disabled in OEM firmware)
MAC addresses (OEM and OpenWrt):
fw_env @ 0x00 d4🆎82:??:??:?a LAN (eth1)
fw_env @ 0x06 d4🆎82:??:??:?b WAN (eth2)
fw_env @ 0x0c d4🆎82:??:??:?c WLAN 2.4 GHz (ath1)
fw_env @ 0x12 d4🆎82:??:??:?d WLAN 5 GHz (ath0)
fw_env @ 0x18 d4🆎82:??:??:?e OEM usage unknown (eth0 in OpenWrt)
OID d4🆎82 is registered to:
ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US
More info:
https://openwrt.org/inbox/toh/arris/tr4400_v2
IMPORTANT:
This port requires moving the 'fw_env' partition prior to first boot to
consolidate 70% of the usable space in flash into a contiguous partition.
'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords.
Its contents must be copied to 'rootfs_1' prior to booting via initramfs.
Note that the stock 'fw_env' partition will be wiped during sysupgrade.
A writable 'stock_fw_env' partition pointing to the old, stock location
is included in the port to help rolling back this change if desired.
Installation:
- Requires serial access and a TFTP server.
- Fully boot stock, press ENTER, type in:
mtd erase /dev/mtd21
dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21
umount /config && ubidetach -m 23 && mtd erase /dev/mtd23
- Reboot and interrupt U-Boot by pressing a key, type in:
set mtdids 'nand0=nand0'
set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)'
set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm'
env save
- Setup TFTP server serving initramfs image as 'recovery.bin', type in:
set ipaddr 192.168.1.1
set serverip 192.168.1.2
tftpboot recovery.bin && bootm
- Use sysupgrade to install squashfs image.
This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
[add 5.15 changes for 0069-arm-boot-add-dts-files.patch]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Add NVRAM quirks script for the bcm53xx target. Split NVRAM quirks for the
bcm47xx and bcm53xx targets. Move clear partialboot NVRAM quirk for Linksys
EA9500 here. Add set wireless LED behaviour quirk for Asus RT-AC88U.
Use boot() instead of start() as nvram commands are meant to be executed
only once, at boot.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
this adds the new dts-binding "mediatek,led_source"
currently for MT7628AN and MT7688 built-in switches,
which is documented as a 3-bit field configuring the
switch LEDs for various control schemes from 0 to 3.
Normally this is not needed, but e.g. for Asus RT-AC1200-V2
it is a must to set it to the anyway undocumented value
of 4, to have the switch LEDs react correctly on link/act
events. This is an MT7628DAN device, but I doubt this is
a speciality of this particular SoC.
Also added the RT305X_ESW_LED_OFF value to LED states.
Did also rename the register RT5350_EWS_REG_LED_POLARITY
to RT5350_EWS_REG_LED_CONTROL, which is the correct name.
Also making use of defines for some hardcoded values.
Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
This patch configures kernel testing version for kirkwood target.
Compile tested: all
Run tested: Endian 4i
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This patch makes only a copy of 5.10 config and patches.
Patches merged in upstream was omited.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Patch that corrects sleep clock frequency has already been backported
to 5.15 stable so remove the duplicate patch.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add 5.15 kernel as a testing kernel version in the Makefile.
Linksys EA6350v3/EA8300/MR8300 will not build with buildbot settings and
should be disabled when the target is switched, unless the image size is
reduced again.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
[add comment for increased kernel size]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Kernel 5.15 have some new api for ethtool and phy.
Add ifdef to fix compilation error.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
The 2.4GHz interface doesn't come up properly with the log showing:
mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
As seen on other MT7621 boards this is caused by a missing reset GPIO.
The MT7621 dtsi set GPIO 19 as PCIe reset GPIO, which on this board
reset the 5GHz interface on port 0. Add GPIO 8 to the PCIe reset GPIO
list to also reset the 2.4GHz interface on port 1.
Signed-off-by: Alban Bedel <albeu@free.fr>
SoC: Atheros AR7161
RAM: DDR 128 MiB (hynix h5dU5162ETR-E3C)
Flash: SPI-NOR 8 MiB (mx25l6406em2i-12g)
WLAN: 2.4/5 GHz
2.4 GHz: Atheros AR9220
5 GHz: Atheros AR9223
Ethernet: 4x 10/100/1000 Mbps (Atheros AR8021)
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: RJ45 9600,8N1
Power: 12 VDC, 1.0 A
Installation instruction:
0. Make sure you have latest original firmware (3.7.11.4)
1. Connect to the Serial Port with a Serial Cable RJ45 to DB9/RS232
(9600,8N1)
screen /dev/ttyUSB0 9600,cs8,-parenb,-cstopb,-hupcl,-crtscts,clocal
2. Configure your IP-Address to 192.168.1.42
3. When device boots hit spacebar
3. Configure the device for tftpboot
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.42
saveenv
4. Reset the device
reset
5. Hit again the spacebar
6. Now load the image via tftp:
tftpboot 0x81000000 INITRAMFS.bin
7. Boot the image:
bootm 0x81000000
8. Copy the squashfs-image to the device.
9. Do a sysupgrade.
https://openwrt.org/toh/netgear/wndap360
The device should be converted from kmod-owl-loader to nvmem-cells in the
future. Nvmem cells were not working. Maybe ATH9K_PCI_NO_EEPROM is missing.
That is why this commit is still using kmod-owl-loader. In the future
the device tree may look like this:
&ath9k0 {
nvmem-cells = <&macaddr_art_120c>, <&cal_art_1000>;
nvmem-cell-names = "mac-address", "calibration";
};
&ath9k1 {
nvmem-cells = <&macaddr_art_520c>, <&cal_art_5000>;
nvmem-cell-names = "mac-address", "calibration";
};
&art {
...
cal_art_1000: cal@1000 {
reg = <0x1000 0xeb8>;
};
cal_art_5000: cal@5000 {
reg = <0x5000 0xeb8>;
};
};
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add USB power control in DTS for GL.iNet models:
- AR300M;
- AR300M-Ext;
- AR300M16;
- AR300M16-Ext.
Signed-off-by: PtilopsisLeucotis <PtilopsisLeucotis@yandex.com>
This commit adds support for the TP-Link Deco M4R (it can also be M4,
TP-Link uses both names) v1 and v2. It is similar hardware-wise to the
Archer C6 v2. Software-wise it is very different. V2 has a bit different
layout from V1 but the chips are the same and the OEM firmware is the same
for both versions.
Specifications:
SoC: QCA9563-AL3A
RAM: Zentel A3R1GE40JBF
Wireless 2.4GHz: QCA9563-AL3A (main SoC)
Wireless 5GHz: QCA9886
Ethernet Switch: QCA8337N-AL3C
Flash: 16 MB SPI NOR
Flashing:
The device's bootloader only accepts images that are signed using
TP-Link's RSA key, therefore this way of flashing is not possible. The
device has a web GUI that should be accessible after setting up the device
using the app (it requires the app to set it up first because the web GUI
asks for the TP-Link account password) but for unknown reasons, the web
GUI also refuses custom images.
There is a debug firmware image that has been shared on the device's
OpenWrt forum thread that has telnet unlocked, which the bootloader will
accept because it is signed. It can be used to transfer an OpenWrt image
file over to the device and then be used with mtd to flash the device.
Pre-requisites:
- Debug firmware.
- A way of transferring the file to the router, you can use an FTP server
as an example.
- Set a static IP of 192.168.0.2/255.255.255.0 on your computer.
- OpenWrt image.
Installation:
- Unplug your router and turn it upside down. Using a long and thin object
like a SIM unlock tool, press and hold the reset button on the router and
replug it. Keep holding it until the LED flashes yellow.
- Open 192.168.0.1. You should see the bootloader recovery's webpage.
Choose the debug firmware that you downloaded and flash it. Wait until the
router reboots (at this stage you can remove the static IP).
- Open a terminal window and connect to the router via telnet (the primary
router should have a 192.168.0.1 IP address, secondary routers are
different).
- Transfer the file over to the router, you can use curl to download it
from the internet (use the insecure flag and make sure your source accepts
insecure downloads) or from an FTP server.
- The router's default mtd partition scheme has kernel and rootfs
separated. We can use dd to split the OpenWrt image file and flash it with
mtd:
dd if=openwrt.bin of=kernel.bin skip=0 count=8192 bs=256
dd if=openwrt.bin of=rootfs.bin skip=8192 bs=256
- Once the images are ready, you have to flash the device using mtd
(make sure to flash the correct partitions or you may be left with a
hard bricked router):
mtd write kernel.bin kernel
mtd write rootfs.bin rootfs
- Flashing is done, reboot the device now.
Signed-off-by: Foica David <superh552@gmail.com>
The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports
and one USB 3.0 port.
It's also known as Wavlink QUANTUM T8.
Hardware
--------
SoC: Mediatek MT7621A
RAM: 128MB (Nanya NT5CB64M16GP-EK)
FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3)
ETH:
- 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
- 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC
- 1x MT7615NE (4x4:4) 5GHz
- 8 external antennas
BTN:
- 1x Reset button
- 1x WPS button
- 1x Turbo button
- 1x Touchlink button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
- 1x USB 3.0 port
UART:
- 57600-8-N-1
J4
Everything works correctly.
Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
(Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204)
Restore OEM Firmware
--------------------
Flash the firmware update available online directly from LUCI.
You can download it from:
https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:63 (factory @ 0xe006)
WAN XX:XX:XX:XX:XX:64 (factory @ 0xe000)
WIFI 2G/5G XX:XX:XX:XX:XX:65 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:66 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:65
In OEM firmware the DBDC wifi interfaces have these mac addresses:
2G) 82:XX:XX:XX:XX:65
5G) 80:XX:XX:XX:XX:65
While in OpenWrt the addresses are:
2G) 80:XX:XX:XX:XX:65
5G) 02:XX:XX:XX:XX:65
2) radio0 will show as 2G/5G interface but only 2G is really usable.
3) There is just one wifi led for all wifi interfaces.
It currently shows only the radio0 GHz wifi activity.
4) My unit was shipped with M33A8.V5030.190716 firmware which contains
the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in
the input box it will start the telnet daemon. Now you can access
the telnet console on port 2323 with these credentials:
username: admin2860
password: admin
5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the
webcmd.shtml page. If your router is shipped with a previous firmware
version and you want to back it up, you can follow the back up
procedure of the WS-WN583A6.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Most of the definitions for WN531A6 will be shared with WN533A8 in a
future commit, so put them in a shared DTSI.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
In commit 7e614820a8 ("mpc85xx: add support for Extreme Networks
WS-AP3825i"), we borrowed a recipe convention from apm821xx for device
tree blob padding. Unfortunately, in the apm821xx target, the image
recipes name the device tree blob differently, meaning that in
mpc85xx, the padded dtb is never consumed.
Change the definition of `Build/dtb` so that it outputs the padded dtb
to the correct location for it to be consumed.
Also, rename the recipe to `Build/pad-dtb`, so it is clear we
are building and padding the device tree blob.
This change fixes Github issue #9779 [1].
[1]: https://github.com/openwrt/openwrt/issues/9779
Fixes: 7e614820a8 ("mpc85xx: add support for Extreme Networks WS-AP3825i")
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
The config for LEDS_UBNT_LEDBAR doesn't stay in mt7629 kconfig because
of its I2C dependency. Build it as a module and let buildroot handle
this config option instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Disable support for joysticks, micee and tablets. There's no actual
driver selected in kconfig, and including kernel support is just a
waste of space. Besides that, I believe nobody wants these on a router.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>