If logfacility is a path to a file it needs to be r/w mounted in the
sandbox as well for dnsmasq to work.
Reported-by: @iointerrupt
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
There are two versions which are identical apart from the enclosure:
YunCore AX820: indoor ceiling mount AP with integrated antennas
YunCore HWAP-AX820: outdoor enclosure with external (N) connectors
Hardware specs:
SoC: MediaTek MT7621DAT
Flash: 16 MiB SPI NOR
RAM: 128MiB (DDR3, integrated)
WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax
Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN)
LED: Status (green)
Button: Reset
Power: 802.11af/at PoE; DC 12V,1A
Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external
Flash instructions:
The "OpenWRT support" version of the AX820 comes with a LEDE-based
firmware with proprietary MTK drivers and a luci webinterface and
ssh accessible under 192.168.1.1 on LAN; user root, no password.
The sysupgrade.bin can be flashed using luci or sysupgrade via ssh,
you will have to force the upgrade due to a different factory name.
Remember: Do *not* preserve factory configuration!
MAC addresses as used by OEM firmware:
use address source
2g 44:D1:FA:*:0b Factory 0x0004 (label)
5g 46:D1:FA:*:0b LAA of 2g
lan 44:D1:FA:*:0c Factory 0xe000
wan 44:D1:FA:*:0d Factory 0xe000 + 1
The wan MAC can also be found in 0xe006 but is not used by OEM dtb.
Due to different MAC handling in mt76 the LAA derived from lan is used
for 2g to prevent duplicate MACs when creating multiple interfaces.
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Replace pending patch with version accepted upstream.
Other than in the first suggested version, the new property is now
called 'u-boot,bootconf' instead of 'bootconf'.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove '0x' prefix from pstore node in dts, just like it was done
for the device tree used by Linux on MT7622.
This change is done in preparation to update U-Boot to 2022.04.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Attempt to minimize the time during which an interrupted nand sysupgrade
can lead to a non-functional device by flushing caches before starting
the upgrade procedure.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Fix issues while retaining configuration during nand sysupgrade:
- abort configuration saving if data partition is not found
- generate diagnostics if saving fails (eg, because of lack of space)
- do not output "sysupgrade successful" in case of errors
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Remove redundant check from nand ubinized sysupgrade code. This check
has already been done in the only caller of the affected function:
nand_do_upgrade.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Prepares code for ubirename-based safe sysupgrade implementation.
Fixes several issues:
- the special CI_KERNPART value "none" is ignored if an MTD partition
named "none" exists
- misleading variable names (such as has_kernel to mean "tar has kernel
and it should not be written to an MTD partition but a UBI volume")
- inconsistent treatment of zero-length tar member files
- inconsistent meaning of "0" and "" variable values
- redundant operations (unneeded untaring, repeated untaring, unneeded
partition lookups)
- inconsistent variable quoting
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Ensure that the kernel CRC is invalidated while rootfs is being updated.
This allows the bootloader to detect an interrupted sysupgrade and fall
back to an alternate booting method, such as TFTP, instead of just going
ahead with normal boot and effectively bricking the device.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Ensure that the kernel CRC is invalidated while rootfs is being updated.
This allows the bootloader to detect an interrupted sysupgrade and fall
back to an alternate booting method, instead of just going ahead with
normal boot and effectively bricking the device.
Possible fallbacks include a recovery initramfs partition or UBI volume
and TFTP. See here for an example U-Boot configuration with fallbacks:
https://shorturl.at/befsA (https://github.com/Lanchon/openwrt-tr4400-v2/
blob/e7d707d6bd7839fbd0b8d0bd180fce451df77e47/install-recovery.sh#L52-L63)
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Emit diagnostics if nand sysupgrade is aborted because UBI partition
cannot be attached. Also avoid redudndant checks.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
This reverts commit f9ff282d17 as during
upstream patch review process nbd pointed out, that this patch needs
more work:
"The patch looks wrong to me. I'm pretty sure that AR_CH0_TOP2 is the
correct register, the definition has an explicit check for 9561 as well.
I believe this patch works by accident because it avoids writing a wrong
value to that register."
1. https://lore.kernel.org/all/91c58969-c60e-2f41-00ac-737786d435ae@nbd.name
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The ZyXEL GS1900-24HP v1 is a 24 port PoE switch with two SFP ports,
similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HP v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 24 ethernet port PoE status LEDs
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* PoE:
* Management MCU: ST Micro ST32F100 Microcontroller
* 6 BCM59111 PSE chips
* 170W power budget
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a TI or SIPEX 3232C for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HP v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[Add info on PoE hardware to commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The Sophos AP100, AP100C, AP55, and AP55C are dual-band 802.11ac access
points based on the Qualcomm QCA9558 SoC. They share PCB designs with
several devices that already have partial or full support, most notably the
Devolo DVL1750i/e.
The AP100 and AP100C are hardware-identical to the AP55 and AP55C, however
the 55 models' ART does not contain calibration data for their third chain
despite it being present on the PCB.
Specifications common to all models:
- Qualcomm QCA9558 SoC @ 720 MHz (MIPS 74Kc Big-endian processor)
- 128 MB RAM
- 16 MB SPI flash
- 1x 10/100/1000 Mbps Ethernet port, 802.3af PoE-in
- Green and Red status LEDs sharing a single external light-pipe
- Reset button on PCB[1]
- Piezo beeper on PCB[2]
- Serial UART header on PCB
- Alternate power supply via 5.5x2.1mm DC jack @ 12 VDC
Unique to AP100 and AP100C:
- 3T3R 2.4GHz 802.11b/g/n via SoC WMAC
- 3T3R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)
AP55 and AP55C:
- 2T2R 2.4GHz 802.11b/g/n via SoC WMAC
- 2T2R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)
AP100 and AP55:
- External RJ45 serial console port[3]
- USB 2.0 Type A port, power controlled via GPIO 11
Flashing instructions:
This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.
To flash via XG appliance:
- Register on Sophos' website for a no-cost Home Use XG firewall license
- Download and install the XG software on a compatible PC or virtual
machine, complete initial appliance setup, and enable SSH console access
- Connect the target AP device to the XG appliance's LAN interface
- Approve the AP from the XG Web UI and wait until it shows as Active
(this can take 3-5 minutes)
- Connect to the XG appliance over SSH and access the Advanced Console
(Menu option 5, then menu option 3)
- Run `sudo awetool` and select the menu option to connect to an AP via
SSH. When prompted to enable SSH on the target AP, select Yes.
- Wait 2-3 minutes, then select the AP from the awetool menu again. This
will connect you to a root shell on the target AP.
- Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
- Run `mtd -r write /tmp/openwrt.bin astaro_image`
- When complete, the access point will reboot to OpenWRT.
To flash via U-Boot serial console:
- Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
netmask 255.255.255.0
- Copy the firmware .bin to the TFTP server and rename to 'uImage_AP100C'
- Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
- Connect the AP ethernet to your PC's ethernet port
- Connect a terminal to the UART at 115200 8/N/1 as usual
- Power on the AP and press a key to cancel autoboot when prompted
- Run the following commands at the U-Boot console:
- `tftpboot`
- `cp.b $fileaddr 0x9f070000 $filesize`
- `boot`
- The access point will boot to OpenWRT.
MAC addresses as verified by OEM firmware:
use address source
LAN label config 0x201a (label)
2g label + 1 art 0x1002 (also found at config 0x2004)
5g label + 9 art 0x5006
Increments confirmed across three AP55C, two AP55, and one AP100C.
These changes have been tested to function on both current master and
21.02.0 without any obvious issues.
[1] Button is present but does not alter state of any GPIO on SoC
[2] Buzzer and driver circuitry is present on PCB but is not connected to
any GPIO. Shorting an unpopulated resistor next to the driver circuitry
should connect the buzzer to GPIO 4, but this is unconfirmed.
[3] This external RJ45 serial port is disabled in the OEM firmware, but
works in OpenWRT without additional configuration, at least on my
three test units.
[4] On AP100/AP55 models the UART header is accessible after removing
the device's top cover. On AP100C/AP55C models, the PCB must be removed
for access; three screws secure it to the case.
Pin 1 is marked on the silkscreen. Pins from 1-4 are 3.3V, GND, TX, RX
Signed-off-by: Andrew Powers-Holmes <andrew@omnom.net>
This device is from now-defunct BOLT! ISP in Indonesia.
The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision.
Specifications:
- SoC: MediaTek MT7621
- Flash: 32 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 2x internal, non-detachable
- LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1)
Non-programmable "Power" LED
- Buttons: Reset and WPS
Instalation:
Install from TFTP
Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123
Press "1" when turning on the router, and type the initramfs file name
You also need to solder pin header or cable to J4 or neighboring test points (T19-T21)
Pinouts from top to bottom: GND, TX, RX, VCC (3.3v)
Baudrate: 57600n8
There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB.
Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
Python seems to fail to link to libreadline properly because of this.
Not a fatal error but an error nontheless.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The modem is based on Marvell PXA1826 and uses ACM+RNDIS interface to
establish connection with custom commands specific to ZTE modems.
Two variants of modems were discovered, some identifying themselves
as "ZTE", and others as plain "Marvell", the chipset manufacturer.
The modem itself runs a fork of OpenWrt inside, which root shell can be
accessed via ADB interface.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Some modems expose ttyACM as their control ports, which have the
"device" symlink pointing one level down in sysfs tree. Try to find
network interfaces for them as well, this is commonly used for modems
exposing ACM + RNDIS or ACM + ECM interface combinations.
Co-developed-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Some modems expose multiple network interfaces on the same USB device,
causing the connection setup script to fail, because glob matching in
the detection phase causes 'ls' to output more than one interface name
plus their base directories in sysfs. Avoid that by listing the
directories explicitly and then selecting first available interface.
This is the case for some variants of ZTE MF286R built-in modem, which
exposes both RNDIS and CDC-ECM network interfaces, causing the
connection setup to fail.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add ifname property to UCI, which can be used to override the
autodetected interface name in case the detection fails due to having
none or more than one interface exposed by the modem, which is not
explicitly linked to TTY port. This is needed on certain variants of ZTE
MF286R built-in modem, which exposes both RNDIS and CDC-ECM interfaces
on the modem, on which the automatic detection may select the wrong
network interface.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Specification:
- QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR
- 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN)
- 2T2R 802.11b/g/n 2.4GHz
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
ath9k is setting the TX PA DC bias level different on QCA9561 and QCA9565
although they have the same radio IP-core, which results in a very low
output power and very low throughput as devices are further away from
the AP (compared to other 2.4GHz APs.)
In real life testing, without this patch the 2.4GHz throughput on Yuncore
XD3200 is around 10Mbps sitting close to the AP, and close to theoretical
maximum with the patch applied.
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
[edit commit message]
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Specification:
- QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR
- 2T2R 802.11b/g/n 2.4GHz
- 2T2R 802.11n/ac 5GHz
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
LED for 5 GHz WLAN is currently not supported as it is connected directly
to the QCA9882 radio chip.
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Upstream in commit 34a1dee6bc44 ("net: usb: asix: ax88772: add generic
selftest support") in version 5.14 added dependency on generic selftest
functionality and armvirt/64 when compiled with ALL_KMODS=y reports following:
Package kmod-usb-net-asix is missing dependencies for the following libraries:
mdio_devres.ko
selftests.ko
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Upstream in commit 3e1e58d64c3d ("net: add generic selftest support") in
version 5.13 added generic selftests module and usb-net-asix already
depends on it, in version 5.18 via commit 1710b52d7c13 ("net: usb:
smsc95xx: add generic selftest support") it will be used by
usb-net-smsc95xx as well.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
armvirt/64 when compiled with ALL_KMODS=y reports following:
Package kmod-usb-net-smsc95xx is missing dependencies for the following libraries:
libphy.ko
Signed-off-by: Petr Štetiar <ynezz@true.cz>
armvirt/64 when compiled with ALL_KMODS=y reports following:
Package kmod-mdio-devres is missing dependencies for the following libraries:
of_mdio.ko
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Upstream in commit bc1bee3b87ee ("net: mdiobus: Introduce
fwnode_mdiobus_register_phy()") in version 5.14 introduced new
dependency:
Package kmod-of-mdio is missing dependencies for the following libraries:
fwnode_mdio.ko
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 2edc017a6e.
We shouldn't be using a shell script here, but the SeedRNG integration
into OpenWRT requires a bit more thought. Etienne raised some important
points immediately after this was merged and planned to send some follow
up commits, but became busy with other things. The points he raised are
important enough that we should actually back this out until it's ready
to go, and then merge it as a cohesive unit. So let's revert this for
now, and come back to it later on.
Cc: Etienne Champetier <champetier.etienne@gmail.com>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Checking whether /sbin/udhcpc is a symbolic link breaks using the
DHCP proto handler inside procd-ujail where bind-mounts are used for
the resolved link. Check whether /sbin/udhcpc is executable instead
to allow using the proto handler for DHCP-provisioned containers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make sure sysupgrade on NAND also works in case of UBI volumes having
index >9. While at it, also make sure UBI device is detected and abort
in case it isn't. Use Shell built-in shorthand ':' instead of 'true'.
Fixes#9708
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
4cd7d4f Revert "firewall3: support table load on access on Linux 5.15+"
50979cc firewall3: remove unnecessary fw3_has_table
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Both legacy iptables and nftables require nf-log modules for rule logging,
so move them into a separate package both firewall implementations can
depend on.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fixes two high-severity vulnerabilities:
- CVE-2022-25640: A TLS v1.3 server who requires mutual authentication
can be bypassed. If a malicious client does not send the
certificate_verify message a client can connect without presenting a
certificate even if the server requires one.
- CVE-2022-25638: A TLS v1.3 client attempting to authenticate a TLS
v1.3 server can have its certificate heck bypassed. If the sig_algo in
the certificate_verify message is different than the certificate
message checking may be bypassed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This updates mac80211 to version 5.15.33-1 which is based on kernel
5.15.33.
The removed patches were applied upstream.
This new release contains many fixes which were merged into the upstream
Linux kernel.
This also contains the following new drivers which are needed for ath11k:
* net/qrtr/
* drivers/bus/mhi/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
As anyway only the default is called now we can as well also just remove
the override for Build/Configure.
Fixes: e2cffbb805 ("arm-trusted-firmware-mediatek: update to 2021-03-10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix compilation and usage under kernel 5.15 for the mwlwifi driver.
For detailed description of changes, check individual patches.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Changes:
Duncan Roe (5):
nlmsg: Fix a missing doxygen section trailer
build: doc: "make" builds & installs a full set of man pages
build: doc: get rid of the need for manual updating of Makefile
build: If doxygen is not available, be sure to report "doxygen: no" to ./configure
src: doc: Fix messed-up Netlink message batch diagram
Fernando Fernandez Mancera (1):
src: fix doxygen function documentation
Florian Westphal (1):
libmnl: zero attribute padding
Guillaume Nault (1):
callback: mark cb_ctl_array 'const' in mnl_cb_run2()
Kylie McClain (1):
examples: nfct-daemon: Fix test building on musl libc
Laura Garcia Liebana (4):
examples: add arp cache dump example
examples: fix neigh max attributes
examples: fix print line format
examples: reduce LOCs during neigh attributes validation
Pablo Neira Ayuso (3):
doxygen: remove EXPORT_SYMBOL from the output
include: add MNL_SOCKET_DUMP_SIZE definition
build: libmnl 1.0.5 release
Petr Vorel (1):
examples: Add rtnl-addr-add.c
Stephen Hemminger (1):
examples: rtnl-addr-dump: fix typo
igo95862 (1):
doxygen: Fixed link to the git source tree on the website.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Changes:
c63f193 bump version to 1.0.2
3cffa84 libnfnetlink: Check getsockname() return code
90ba679 include: Silence gcc warning in linux_list.h
bb4f6c8 Make it clear that this library is deprecated
e46569c Minimally resurrect doxygen documentation
5087de4 libnfnetlink: hide private symbols
62ca426 autogen: don't convert __u16 to u_int16_t
efa1d8e src: Use stdint types everywhere
7a1a07c include: Sync with kernel headers
7633f0c libnfnetlink: initialize attribute padding to resolve valgrind warnings
94b68f3 configure: uclinux is also linux
617fe82 src: get source code license header in sync with current licensing terms
97a3960 build: resolve automake-1.12 warnings
Removed the patch 100-missing_include.patch, libnfnetlink compiles fine
with musl without this patch.
Signed-off-by: Nick Hainke <vincent@systemli.org>
bh_event_add_var can be called by multiple threads concurrently,
so it shall not use a static char buffer
Signed-off-by: Andrey Erokhin <a.erokhin@inango-systems.com>
92f5e18675bf interface: fix ifname present check in interface status
ef82defaae26 ubus: add active devices to bridger blacklist
Signed-off-by: Felix Fietkau <nbd@nbd.name>
33f1e0b treewide: move json-c compat shims into internal header file
e0e9431 vm: move unhandled exception reporting out of `uc_vm_execute_chunk()`
2b59140 vm: fix callframe double free on unhanded exceptions
7d7e950 main: abort when failing to load a preload library
1032a67 lib: let `json()` accept input objects implementing `read()` method
5ee68d5 fs: implement `fs.readfile()` and `fs.writefile()`
df6b861 ci: debian: change path before attempting to invoke Git operations
dfaf05a ci: debian: automatically update changelog from Git tag
34f3c45 ci: fix YAML syntax of Debian workflow
e956bcf fs: fix off-by-one in fs.dirname() function
6fc4b6c .gitignore: fix overmatching patterns, blacklist cram .venv
7c2e082 build: remove legacy json-c check
77942af build: add polyfills for older libjson-c versions
0b4aaa3 CI: build Debian package
f404285 debian: Add package definition
a37f654 types: fix escape sequence encoding of high byte values in JSON strings
aae5312 Update README.md
8134e25 build: fix symlink install target
87c7296 treewide: replace some leftover "utpl" occurrences, update .gitignore
7d27ad5 build: only stage ucc symlink if compile support is enabled
171402f lib: add date and time related functions
8b5dc60 lib: provide API function to obtain stdlib function implementations
eb0d2f1 main: turn ucode into multicall executable
28ee7e1 uloop: add support for tasks
753dea9 CI: build on macOS
668c5c0 lib: add argument position support (`%m$`) to `sprintf()` and `printf()`
ab46fdf treewide: remove legacy json-c include directives
b8f49b1 tests: 21_regex_literals: generalize syntax error test case
fd2e5e7 tests: 16_sort: fix logic flaw exposed on OS X
2c71bf2 tests: run_tests.sh: pass dummy value to `-T` flag
55c4a90 lib: disallow zero padding for %s formats
0d05cb5 tests: run_tests.sh: use greadlink if available
271e520 resolv: make OS X compatible
d13c320 fs: avoid Linux specific sys/sysmacros.h include on OS X
33397a3 uloop: use execvp() on OS X
bafdc8f lib: add naive sigtimedwait() stub for OS X
ada1585 build: consolidate CMakeLists.txt and cover OS X deviations
befbb69 include: add OS X compatible endian.h header
49838a8 include: rename include guards to avoid clashes with system headers
91f65de nl80211: add missing attributes and correct some attribute flags
b4a1fd5 lib: adjust require(), render() and include() raw mode semantics
4618807 main: rework CLI frontend
73dcd78 lib: fix potential integer underflow on empty render output
c402551 vm: fix crash on object literals with non-string computed properties
efe8a02 syntax: support add new operators
078d686 ubus: add event support
6c66c83 ubus: refactor error and argument handling
1cb04f9 ubus: add object publishing, notify and subscribe support
0e85974 uloop: clear errno before integer conversion attempts
05bd7ed types: treat resource type prototypes as GC roots
a2a26ca lib: introduce uloop binding
6b6d01f vm: release this context on exception in managed method call
1af23a9 tests: fix proto() testcase
4ce69a8 fs: implement access(), mkstemp(), file.flush() and proc.flush()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add a ubus method to request link-measurements from connected STAs.
In addition to the STAs address, the used and maximum transmit power can
be provided by the external process for the link-measurement. If they
are not provided, 0 is used as the default value.
Signed-off-by: David Bauer <mail@david-bauer.net>
5beb87716e70 mt76: dma: add wrapper macro for accessing queue registers
e0bc736d5617 mt76: add support for overriding the device used for DMA mapping
b8c842daa081 mt76: make number of tokens configurable dynamically
87a962e0608f mt76: mt7915: add Wireless Ethernet Dispatch support
2accb74e6be3 mt76: mt7915: fix using null pointer when wfsys on
e5227f2f3120 mt76: mt7921: Fix the error handling path of mt7921_pci_probe()
ec0e9f4da32f mt76: mt7915: fix possible uninitialized pointer dereference in mt7986_wmac_gpio_setup
5a87be892ba7 mt76: mt7915: fix possible NULL pointer dereference in mt7915_mac_fill_rx_vector
fe441e5d3dcf mt76: mt7915: do not pass data pointer to mt7915_mcu_muru_debug_set
f3ddfe886283 mt76: mt7915: report rx mode value in mt7915_mac_fill_rx_rate
2a0d370cb5fe mt76: mt7915: use 0xff to initialize bitrate_mask in mt7915_init_bitrate_mask
506bb0605e3e mt76: mt7921: Add AP mode support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Two patches were removed because of the changes introduced in upstream:
1. 110-mx6cuboxi-mmc-fallback.patch
Looks like similar changes were introduced in 6c3fbf3e456c ("mx6cuboxi:
customize board_boot_order to access eMMC").
2. 111-mx6cuboxi_defconfig-force-mmc-boot.patch
The 'CONFIG_SPL_FORCE_MMC_BOOT' was removed in 15aec318ef03 ("Revert
"imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC boot on falcon
mode").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The host-build of libselinux requires libsepol/host.
Add the libsepol/host to HOST_BUILD_DEPENDS to allow build on hosts
which don't have libsepol installed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Problem exist when dnsmasq is exclusively bind to particular interface.
After reconfiguring or restarting this interface, its index changes, but
dnsmasq uses the old one. When this problem occurs, dnsmasq does not
listen on the correct interface so DHCP does not work, and clients do not
get an IP address. Procd netdev param can be added to restart dnsmasq when
the interface index is changed.
Signed-off-by: Valentyn Datsko <valikk.d@gmail.com>
[combined into a single &&-connected statement]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This package uses BPF to create a fast path which improves bridging performance
by bypassing the bridge layer. It also supports creating tc offload rules for
hardware that supports it.
Hardware offload support can be used with MT7622 + MT7915 once it is merged
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Replace the tc-full dependency with tc + libnl-tiny
1cd5e12eecdc loader/interface: attach bpf program directly using netlink
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MHI WWAN CTRL allows QCOM-based PCIe modems to expose different modem
control protocols/ports to userspace, including AT, MBIM, QMI, DIAG
and FIREHOSE. These protocols can be accessed directly from userspace
(e.g. AT commands) or via libraries/tools (e.g. libmbim, libqmi, libqcdm)
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This driver provides MHI PCI controller driver for devices
such as Qualcomm SDX55 based PCIe modems
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Previously commit openwrt/packages@3abb7cb ("lvm2: Added script and updated Makefile[...]")
couldn't actually work and allow rootfs_data to be stored on a LVM2 as
the necessary kernel modules had not been loaded at this point.
Fix this by loading device-mapper modules early at boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the kernel's built-in formula for computing this value.
The value applied by OpenWRT's sysctl configuration file does not scale
with the available memory, under-using hardware capabilities.
Also, that formula also influences net.netfilter.nf_conntrack_buckets,
which should improve conntrack performance in average (fewer connections
per hashtable bucket).
Backport upstream commit for its effect on the number of connections per
hashtable bucket.
Apply a hack patch to set the RAM size divisor to a more reasonable value (2048,
down from 16384) for our use case, a typical router handling several thousands
of connections.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
A Python script containing an unreproducible path is copied by default.
Remove it before generating the package.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The first argument for snprintf is the buffer and the 2. one is the
size. Fix the order. This broke the lock application.
Fixes: 34567750db ("busybox: fix busybox lock applet pidstr buffer overflow")
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes following issue:
Package kmod-drm-imx-ldb is missing dependencies for the following libraries:
drm_dp_aux_bus.ko
Introduced upstream in commit aeb33699fc2c ("drm: Introduce the DP AUX
bus") in kernel version 5.15.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes following issue:
Package kmod-drm is missing dependencies for the following libraries:
fb.ko
Introduced upstream in commit f611b1e7624c ("drm: Avoid circular
dependencies for CONFIG_FB") in 5.14.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Kernel setting `/proc/sys/kernel/pid_max` can be set up to 4194304 (7
digits) which will cause buffer overflow in busbox lock patch, this
often happens when running in a rootfs container environment.
This commit enlarges `pidstr` to 12 bytes to ensure a sufficient buffer
for pid number and an additional char '\n'.
Signed-off-by: Qichao Zhang <njuzhangqichao@gmail.com>
Fixes following build issues:
Package kmod-r8169 is missing dependencies for the following libraries:
mdio_devres.ko
Package kmod-ixgbe is missing dependencies for the following libraries:
mdio_devres.ko
Package kmod-amd-xgbe is missing dependencies for the following libraries:
mdio_devres.ko
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The RNG can't actually be seeded from a shell script, due to the
reliance on ioctls. For this reason, the seedrng project provides a
basic script meant to be copy and pasted into projects like OpenWRT
and tweaked as needed: <https://git.zx2c4.com/seedrng/about/>.
This commit imports it into the urandom-seed package and wires up the
init scripts to call it. This also is a significant improvement over the
current init script, which does not robustly handle cleaning up of seeds
and syncing to prevent reuse. Additionally, the existing script creates
a new seed immediately after writing an old one, which means that the
amount of entropy might actually regress, due to failing to credit the
old seed.
Closes: https://github.com/openwrt/openwrt/issues/9570
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [fixed missing INSTALL_DIR]
List of changes since previous release from 2018 is quite long:
* Fix crc32.c to compile local functions only if used.
* Check for cc masquerading as gcc or clang in configure.
* Remove destructive aspects of make distclean.
* Separate out address sanitizing from warnings in configure.
* Eliminate use of ULL constants.
* Add fallthrough comments for gcc.
* Clean up minizip to reduce warnings for testing.
* Fix unztell64() in minizip to work past 4GB. (Daniël Hörchner)
* minizip warning fix if MAXU32 already defined. (gvollant)
* Replace black/white with allow/block. (theresa-m)
* Fix indentation in minizip's zip.c.
* Improve portability of contrib/minizip.
* Correct typo in blast.c.
* Change macro name in inflate.c to avoid collision in VxWorks.
* Clarify gz* function interfaces, referring to parameter names.
* Fix error in comment on the polynomial representation of a byte.
* Fix memory leak on error in gzlog.c.
* Avoid adding empty gzip member after gzflush with Z_FINISH.
* Explicitly note that the 32-bit check values are 32 bits.
* Use ARM crc32 instructions if the ARM architecture has them.
* Add use of the ARMv8 crc32 instructions when requested.
* Correct comment in crc32.c.
* Don't bother computing check value after successful inflateSync().
* Use atomic test and set, if available, for dynamic CRC tables.
* Speed up software CRC-32 computation by a factor of 1.5 to 3.
* Add crc32_combine_gen() and crc32_combine_op() for fast combines.
* Add tables for crc32_combine(), to speed it up by a factor of 200.
* Fix the zran.c example to work on a multiple-member gzip file.
* Add gznorm.c example, which normalizes gzip files.
* Show all the codes for the maximum tables size in enough.c.
* Clarify that prefix codes are counted in enough.c.
* Use inline function instead of macro for index in enough.c.
* Clean up code style in enough.c, update version.
* Use a macro for the printf format of big_t in enough.c.
* Use a structure to make globals in enough.c evident.
* Assure that the number of bits for deflatePrime() is valid.
* Fix a bug that can crash deflate on some input when using Z_FIXED.
* Correct the initialization requirements for deflateInit2().
* Emphasize the need to continue decompressing gzip members.
* Add legal disclaimer to README.
* Fix deflateEnd() to not report an error at start of raw deflate.
* Remove old assembler code in which bugs have manifested.
* Make the names in functions declarations identical to definitions.
* Avoid an undefined behavior of memcpy() in _tr_stored_block().
* Avoid undefined behaviors of memcpy() in gz*printf().
* Avoid an undefined behavior of memcpy() in gzappend().
* Avoid the use of ptrdiff_t.
* Handle case where inflateSync used when header never processed.
* Don't compute check value for raw inflate if asked to validate.
* Add address checking in clang to -w option of configure.
* Return an error if the gzputs string length can't fit in an int.
* Small speedup to inflate [psumbera].
* Update use of errno for newer Windows CE versions.
* Avoid some conversion warnings in gzread.c and gzwrite.c.
* Have Makefile return non-zero error code on test failure.
* Avoid a conversion error in gzseek when off_t type too small.
* Fix CLEAR_HASH macro to be usable as a single statement.
* Fix bug when window full in deflate_stored().
* Limit hash table inserts after switch from stored deflate.
* Permit a deflateParams() parameter change as soon as possible.
* Cygwin does not have _wopen(), so do not create gzopen_w() there.
Removed 006-fix-compressor-crash-on-certain-inputs.patch which was
hotfix for CVE-2018-25032 and is now included in this release.
This release is not available on @SF (yet?) so the sources are now
pulled from GitHub.
Fixes: CVE-2018-25032
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The inclusion of the kmod-leds-uleds into the userspace
nu801 package causes a circular dependency inside the
buildsystem... which causes it to be picked regardless
of other DEPENDS values.
In case of the mx100, this could be solved by moving the
kmod-leds-uled dependency to the kmod-meraki-mx100.
Bonus: drop @!LINUX_5_4 from kmod-meraki-mx100
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Chen Minqiang reported that he has troubles downloading nu801.
His logs showed the followin TLS Handshake failure.
|Checking out files from the git repository...
|Cloning into 'nu801-d9942c0c'...
|fatal: unable to access 'https://github.com/chunkeey/nu801.git/':
| gnutls_handshake() failed: The TLS connection was non-properly terminated.
|Makefile:39: recipe for target '[...]/dl/nu801-d9942c0c.tar.xz' failed
This can be fixed by providing a PKG_MIRROR_HASH. The download
scripts will now be able to pull the source from OpenWrt's source
archive, which should be available through HTTP.
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
intl is not included in libc, disable it as is done with the target
package.
argp is also not included. Add build depends for argp-standalone.
fts is also not included. Add build depends for musl-fts.
Disable shared libraries to avoid having to manually add rpath.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Getting rid of shared libraries for hostpkg avoids having to use rpath
hacks to find the library. It also fixes compilation with host glib2
binaries.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Avoids having to add rpath to the various packages using it. Also add
PIC to fix compilation as static libraries do not use PIC by default.
Fixes: 1fb099341e ("musl-fts: add host build")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Add new module require in 5.15
- Changes in block module
- Changes in netfilter module (log module unified)
- Changes in fs module (mainly new depends for cifs and new ntfs3 module)
- Changes in lib add shared lib now used by more than 1 kmod
- Changes in crypto, dropped one crypto algo added arm crypto accellerator
- Changes in other, add zram default compressor choice and missing lib
by tpm module
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Modified the radio frequency hardware part of e2600ac c1/c2,
need to cooperate with the modified board.bin file, the device
can work normally.
Signed-off-by: 张 鹏 <sd20@qxwlan.com>
This reverts commit 80b7a8a7f5.
Now that 5.10 is the default kernel for all platforms, we can
bring back the NU801 userspace driver for platforms that rely
on it. Currently it's used on the MX100 x86_64 target, but
other Meraki platforms use this controller.
Note that we also now change how we load nu801. The way we did
this previously with procd worked, but it meant it didn't load
until everything was up and working.
To fix this, let's call nu801 from boot and re-trigger the
preinit blink sequence. Since nu801 runs as a daemon this is
now something we can do.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
(removed empty line, currently only MX100 uses it so: @TARGET_x86)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
See firmware-utils.git commits [1], which implemented the cros-vbutil
verified-boot payload-packing tool, and extended ptgen for the CrOS
kernel partition type. With these, it's now possible to package kernel +
rootfs to make disk images that can boot a Chrome OS-based system (e.g.,
Chromebooks, or even a few AP models).
Regarding PARTUUID= changes: Chromium bootloaders work well with a
partition number offset (i.e., relative to the kernel partition), so
we'll be using a slightly different root UUID line.
NB: I've made this support specific to ip40xx for now, because I only
plan to support an IPQ4019-based AP that uses a Chromium-based
bootloader, but this image format can be used for essentially any
Chromebook, as well as the Google OnHub, a prior Chromium-based AP using
an IPQ8064 chipset.
[1]
ptgen: add Chromium OS kernel partition support
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=6c95945b5de973026dc6f52eb088d0943efa96bb
cros-vbutil: add Chrome OS vboot kernel-signing utility
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=8e7274e02fdc6f2cb61b415d6e5b2e1c7e977aa1
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
From a manufacturer's image (version R89-13729.57.27), with appopriate
',variant=' appended to the board names:
$ .../qca-swiss-army-knife/tools/scripts/ath10k/ath10k-bdencoder \
-i ./board-google_wifi.qca4019
FileSize: 48596
FileCRC32: 3966df5d
FileMD5: d54161b0fb9e93691c4272649c37535a
BoardNames[0]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=GO_GALE'
BoardLength[0]: 12064
BoardCRC32[0]: e117f336
BoardMD5[0]: ea35e78c88a8571201da8b75edc9b881
BoardNames[1]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=GO_GALE'
BoardLength[1]: 12064
BoardCRC32[1]: 6c751ec9
BoardMD5[1]: 44cbc4ca6cb7141ba4249615f7065582
BoardNames[2]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=GO_BREEZE'
BoardLength[2]: 12064
BoardCRC32[2]: 24fba117
BoardMD5[2]: b4ac055b3ab67d5a6f5607a96af39a1f
BoardNames[3]: 'bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=GO_BREEZE'
BoardLength[3]: 12064
BoardCRC32[3]: a3e16b2a
BoardMD5[3]: 8b26cb285032314247304114b8ac50e7
Naming follows existing Google projects included in upstream board-2.bin
-- GO(ogle) prefix, an underscore (_), and the project code name, all in
caps.
Note that I only tested the "gale" model; the "breeze" model is a later
revision (same marketing name) with very small hardware changes but
otherwise using the same firmware image.
Submitted upstream here:
ath10k-firmware: QCA4019: hw1.0: Add Google Wifi BDFs
http://lists.infradead.org/pipermail/ath10k/2022-March/013465.htmlhttps://lore.kernel.org/ath10k/YjaNGW252Ls%2FyDw8@localhost/
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fixes compilation under musl based distros like Alpine Linux.
Also add pcre/host as a build dependency as it's needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Some configure scripts look for msgfmt and gmsgfmt. As we don't install
the latter, configure might pick up one from staging_dir/hostpkg, and
the other from the host:
checking for msgfmt... /home/stijn/Development/OpenWrt/openwrt/staging_dir/hostpkg/bin/msgfmt
checking for gmsgfmt... /usr/bin/gmsgfmt
This could potentially lead to hard to debug undefined behaviour.
Install a symlink in the host install phase to avoid this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Evaluating the return value of 'json_load' didn't work in the
intended way resulting in PIN status no longer being read on modems
where --get-pin-status doesn't fail.
Fix this by trying --get-pin-status first and checking if pin1_status
field exists in JSON, and if it doesn't try again with
--uim-get-sim-state.
Fixes: #9501
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tavis has just reported, that he was recently trying to track down a
reproducible crash in a compressor. Believe it or not, it really was a
bug in zlib-1.2.11 when compressing (not decompressing!) certain inputs.
Tavis has reported it upstream, but it turns out the issue has been
public since 2018, but the patch never made it into a release. As far as
he knows, nobody ever assigned it a CVE.
Suggested-by: Tavis Ormandy <taviso@gmail.com>
References: https://www.openwall.com/lists/oss-security/2022/03/24/1
Signed-off-by: Petr Štetiar <ynezz@true.cz>
engine.mk is supposed to be included by engine packages, but it will not
be present in the SDK in the same place as in the main repository.
Move it to include/openssl-engine.mk to avoid this.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
860ca90 odhcpd: Support for Option NTP and SNTP
83e14f4 router: advertise removed addresses as invalid in 3 consecutive RAs
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Albeit a separate crypto module, lzo-rle uses the same kernel library as lzo.
Crypto API users (zram, for example) expect both lzo and lzo-rle to be
available, so let's include lzo-rle (about 5.5 kiB) in the lib-lzo package.
Based on e9hack's original patch: https://patchwork.ozlabs.org/project/openwrt/patch/541cbfbd-76f2-59b3-a867-47b6f0fc7da9@gmail.com/
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Store selected boot configuration in '/chosen' node in device tree, so
it can be accessed by Linux (and used for fine-tuning the FIT partition
parser).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Shuttle KD20 has NAND flash with 0x20000 (128KiB) erase blocks.
Correctly set that in uboot-envtools as well to allow writing to the
bootloader environment using fw_setenv.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
391a9fbd5ace dns: fix parsing vlan encapsulated protocol
6aeeddbc91ad interface: extend dns filters to cover vlan tagged traffic as well
1ab53d4ca601 bpf: return TC_ACT_UNSPEC to allow other filters to proceed
ca21e729af23 interface: switch to using clsact for filters
5d158f6b3c15 interface: run ingress bpf filter on main device ingress instead of ifb egress
bdfcb11847ce interface: fix duplicated dns filter line
b97405aa632a Revert "ubus: remove dnsmasq subscriber"
8fbaf39dbc95 interface: rework adding/removing filters, do not delete clsact
d7ba5804eae4 interface: replace open-coded ifb-dns string with QOSIFY_DNS_IFNAME
91cf440db9e2 loader: fix use of deprecated functions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
v2022.01 has a regression that broke eMMC usage on most if not all Armada
SoC-s, thus breaking boards like uDPU which use eMMC for storage.
Fix it by backporting a recent upstream patch.
Fixes: 782d4c8306 ("uboot-mvebu: update to version 2022.01")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Some users noticed repeated resyncs at random intervals, which go away
when the MEI driver is configured to use polling instead of interrupts.
Debugging shows that this seems to be caused by concurrent calls to
MEI_ReadMailbox (in the interrupt handler) and MEI_WriteMailbox. This
appears to be mostly triggered when there is an interrupt for vectoring
error reports.
In polling mode, calls to MEI_ReadMailbox are protected by the same
semaphore as is used in MEI_WriteMailbox. When interrupts are used,
MEI_WriteMailbox appears to rely on MEI_DisableDeviceInt and
MEI_EnableDeviceInt to provide mutual exclusion with the interrupt
handler. These functions mask/unmask interrupts, and there is an
additional check of the mask in the interrupt handler itself. However,
this is not sufficient on systems with SMP, as the interrupt handler
may be running in parallel, and could already be past the interrupt
mask check at this point.
This adds a lock to the interrupt handler, and also acquires this lock
in MEI_DisableDeviceInt. This should make sure that after a call to
MEI_DisableDeviceInt the interrupt is masked, and the interrupt handler
is either not running, has alread finished its work, or is still before
the interrupt mask check, and is thus going to detect the change.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
This tells the modem about the WAN MAC address, which is used as source
address for vectoring error reports that are generated by the firmware.
It needs to be set early, as the MEI driver only actually writes the
value to the modem when is in reset state (i.e. the firmware has been
loaded, but connection has not started yet).
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
This re-enables the vectoring error sample callback and adds a
dependency to the corresponding driver.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
In order to calculate the required pre-distortion for downstream
vectoring, the vectoring control entity (VCE) at the carrier office
needs error samples from the modem. On Lantiq VR9 modems, error reports
are generated by the firmware, but need to be multiplexed into the data
stream by the driver on the main processor when L2 encapsulation is
selected by the VCE.
This driver provides the necessary callback function, which is called by
the MEI driver after receiving an error report from the firmware.
Originally, it is part of the Lantiq PPA driver, but after a few changes
it also works with the PTM driver used in OpenWrt. The direct call to
ndo_start_xmit needs to be replaced, as the PTM driver relies on locks
from the kernel. Instead dev_queue_xmit is used, which is called from a
work queue, as it is not safe to call from an interrupt handler.
Additional changes include fixes to support recent kernel versions and
a change of the used interface from ptm0 to dsl0.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Also known as the "Xiaomi Router AX3200" in western markets,
but only the AX6S is widely installation-capable at this time.
SoC: MediaTek MT7622B
RAM: DDR3 256 MiB (ESMT M15T2G16128A)
Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG)
WLAN: 2.4/5 GHz 4T4R
2.4 GHz: MediaTek MT7622B
5 GHz: MediaTek MT7915E
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531B
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8
Power: 12 VDC, 1.5 A
Notes:
U-Boot passes through the ethaddr from uboot-env partition,
but also has been known to reset it to a generic mac address
hardcoded in the bootloader.
However, bdata is also populated with the ethernet mac addresses,
but is also typically never written to. Thus this is used instead.
Installation:
1. Flash stock Xiaomi "closed beta" image labelled
'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'.
(MD5: 5eedf1632ac97bb5a6bb072c08603ed7)
2. Calculate telnet password from serial number and login
3. Execute commands to prepare device
nvram set ssh_en=1
nvram set uart_en=1
nvram set boot_wait=on
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
4. Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://<IP>:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Stock Xiaomi recovery tftp that accepts their signed images,
with default ips of 192.168.31.1 + 192.168.31.100.
Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img)
Triggered by holding reset pin on powerup.
A simple implementation of this would be via dnsmasq's
dhcp-boot option or using the vendor's (Windows only)
recovery tool available on their website.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
A service managed by procd does have a json object with usefull information.
This information could by dumped with the following command.
ubus call service list "{ 'verbose':true, 'name': '<service-name>)'". }"
This line is long and complicated to enter. This commit adds a wrapper
call to the procd service section tool to simplify the input and get the
output faster.
We could now enter the command /etc/initd/<service> info to get the info
faster.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The service command belongs to the procd and does not belong in the
shinit. In the course of the move, the script was also checked with
shellcheck and cleaned up.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Add a patch to add some missing init_extensions{a,b}() calls
Package lib{arp,eb}t_*.so
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
This allows to install ip6tables-nft without iptables-nft
This prepare the addition of {arp,eb}tables-nft
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
This prepare the introduction of ebtables-nft.
Add PROVIDES so dependencies are not broken,
use ALTERNATIVES.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
This prepare the introduction of arptables-nft.
Add PROVIDES so dependencies are not broken,
use ALTERNATIVES.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
- Binary files were renamed to cyfmac from brcmfmac, but the files needs
to be on the router with the previous naming
[ 6.656165] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 6.665182] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.bin failed with error -2
[ 6.674928] brcmfmac mmc1:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac43455-sdio.bin
- Cypress were acquired by Infineon Technologies
Thus change the project URL and switch to download files from their
GitHub repository. This is much better than the previous solution, which
requires finding new threads on their community forum about new driver
updates, and it will be necessary to change the URL each time.
Unfortunately, it seems that there is not published changelog, but
according to this forum thread [1], be careful by opening the link from
solution since it contains ending bracket ), it brings fixes for various
security vulnerabilities, which were fixed in 7_45_234.
Fixes:
- FragAttacks
- Kr00k
Also add LICENSE file
Run tested on Seeedstudio router powered by Raspberry Pi 4 CM with
package cypress-firmware-43455-sdio.
Before:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[ 6.895050] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Mar 23 2020 02:20:01 version 7.45.206 (r725000 CY) FWID 01-febaba43
After:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[ 6.829805] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Apr 15 2021 03:03:20 version 7.45.234 (4ca95bb CY) FWID 01-996384e2
[1] https://community.infineon.com/t5/Wi-Fi-Bluetooth-for-Linux/Outdated-brcmfmac-firmware-for-Raspberry-Pi-4-in-OpenWrt-21-02-1/m-p/331593#M2269
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
drop the use of LIB_SUFFIX
Fixes: 00cbf6f6ab ("bpftools: update to standalone bpftools + libbpf, use the latest version")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rootfs overlays get created at a ROOTDEV_OVERLAY_ALIGN (64KiB)
alignment after the rootfs, but emmc_do_upgrade() is assuming
it comes at the very next 512-byte sector.
Suggested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
(move spaces around, mention fstools' libtoolfs)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This is a bugfix release. Changelog:
*) Fixed a bug in the BN_mod_sqrt() function that can cause it to loop
forever for non-prime moduli. (CVE-2022-0778)
*) Add ciphersuites based on DHE_PSK (RFC 4279) and ECDHE_PSK
(RFC 5489) to the list of ciphersuites providing Perfect Forward
Secrecy as required by SECLEVEL >= 3.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
378b638c70c0 mt76: mt7915: fix unused variable with testmode disabled
4f4309542862 mt76: mt7915: only use u32_get_bits with constant value
de06d828a0bf mt76: mt7921: fix injected MPDU transmission to not use HW A-MSDU
c007ba3ec7a9 mt76: mt7915: simplify conditional
64c74dc93f68 mt76: fix dfs state issue with 160 MHz channels
d3471b0d92c1 mt76: mt7615: honor ret from mt7615_mcu_restart in mt7663u_mcu_init
f4c87b32e0e9 mt76: mt7663u: introduce mt7663u_mcu_power_on routine
82de5987af54 mt76: mt7921: fix up the monitor mode
c501df4086e1 mt76: mt7921: use mt76_hw instead of open coding it
594ee03d5a11 mt76: mt7915: fix DFS no radar detection event
d8d2b383a241 mt76: split single ldpc cap bit into bits
0f336fba20fe mt76: mt7921: make mt7921_init_tx_queues static
00a066ce9914 mt76: mt7921: fix xmit-queue dump for usb and sdio
d6d2479568b2 mt76: mt7921: fix mt7921_queues_acq implementation
d17b74420199 mt76: fix monitor mode crash with sdio driver
c374559eae6f mt76: mt7915: allow beaconing on all chains
b219af63b9ce mt76: connac: add 6 GHz support for wtbl and starec configuration
630384cb3246 mt76: mt7915: add 6 GHz support
28ff1bddc7e8 mt76: mt7915: fix eeprom fields of txpower init values
d4b226cc15e7 mt76: mt7915: add txpower init for 6GHz
31e820d4ce4b mt76: mt7921: get rid of mt7921_wait_for_mcu_init declaration
9fee1faf6028 mt76: mt7915: check for devm_pinctrl_get() failure
31a970940b97 mt76: connac: make read-only array ba_range static const
e49af7036bbc mt76: use le32/16_get_bits() whenever possible
0664d39039c2 mt76: fix invalid rssi report
f16fc9d96105 mt76: mt7915: set band1 TGID field in tx descriptor
67ce2708dcef mt76: mt7915: fix beamforming mib stats
6e899abec818 mt76: mt7915: fix phy cap in mt7915_set_stream_he_txbf_caps()
c6780c85cff2 mt76: mt7915: fix typos in comments
aa6eadc09a83 mt76: usb: add req_type to ___mt76u_rr signature
74a519ab8353 mt76: usb: add req_type to ___mt76u_wr signature
2651d2c66cbd mt76: usb: introduce __mt76u_init utility routine
c03e095eee27 mt76: mt7921: disable runtime pm for usb
41085cdcd7e3 mt76: mt7921: update mt7921_skb_add_usb_sdio_hdr to support usb
e700aba6bae3 mt76: mt7921: move mt7921_usb_sdio_tx_prepare_skb in common mac code
056b7f4ebcc6 mt76: mt7921: move mt7921_usb_sdio_tx_complete_skb in common mac code.
0abf682a3def mt76: mt7921: move mt7921_usb_sdio_tx_status_data in mac common code.
b0c60d5252de mt76: mt7921: add mt7921u driver
053668acdaf8 mt76: mt7921: move mt7921_init_hw in a dedicated work
Signed-off-by: Felix Fietkau <nbd@nbd.name>
LOCK_STATE_HELD define was omitted during backport of
lockdep_assert_not_held() which leads to build failures of kernels with
CONFIG_LOCKDEP=y:
backports-5.15.8-1/backport-include/linux/lockdep.h:16:47: error: 'LOCK_STATE_HELD' undeclared (first use in this function)
Fix it by adding missing LOCK_STATE_HELD define.
References: PR#9373
Reported-by: Oskari Rauta <oskari.rauta@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
FCC ID: 2AG6R-AN700APIAC
Araknis AN-700-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1750
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3
- QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:xb art 0x0
phy1 2.4G *:xc ---
phy0 5GHz *:xd ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: 2AG6R-AN500APIAC
Araknis AN-500-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1200
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9557 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- QCA9882 WLAN PCI card 168c:003c, 5 GHz, 2x2, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:e1 art 0x0
phy1 2.4G *:e2 ---
phy0 5GHz *:e3 ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: U2M-AN300APIN
Araknis AN-300-AP-I-N is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EWS310AP
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- AR9382 WLAN PCI on-board 168c:0030, 5 GHz, 2x2
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM 1839ZFG V59C1512164QFJ25
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:7d art 0x0
phy1 2.4G *:7e ---
phy0 5GHz *:7f ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
The ZyXEL GS1900-24 v1 is a 24 port switch with two SFP ports, similar to
the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24 v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a SIPEX 3232EC for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
> Since the GS1900-24 v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
Add option to compile kmod-inet-diag, support for INET (TCP, DCCP, etc)
socket monitoring interface used by native Linux tools such as ss.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
When porting mwan3 from iptables to nftables I tried the new translation
tool for ipset ipset-translate. I noticed that no IPv6 ipset can be
created with the tool. I have reported the problem to the upstream
project and the following patch fixes the problem.
Until this upsream is included in a new release, this patch should be
used in Openwrt.
https://lore.kernel.org/netfilter-devel/20220228190217.2256371-1-pablo@netfilter.org/T/#m09cc3cb738f2e42024c7aecf5b7240d9f6bbc19c
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
OpenWrt uses a lot of (b)ash scripts for initial setup. This isn't the
best solution as they almost never consider syncing files / data. Still
this is what we have and we need to try living with it.
Without proper syncing OpenWrt can easily get into an inconsistent state
on power cut. It's because:
1. Actual (flash) inode and data writes are not synchronized
2. Data writeback can take up to 30 seconds (dirty_expire_centisecs)
3. ubifs adds extra 5 seconds (dirty_writeback_centisecs) "delay"
Some possible cases (examples) for new files:
1. Power cut during 5 seconds after write() can result in all data loss
2. Power cut happening between 5 and 35 seconds after write() can result
in empty file (inode flushed after 5 seconds, data flush queued)
Above affects e.g. uci-defaults. After executing some migration script
it may get deleted (whited out) without generated data getting actually
written. Power cut will result in missing data and deleted file.
There are three ways of dealing with that:
1. Rewriting all user-space init to proper C with syncs
2. Trying bash hacks (like creating tmp files & moving them)
3. Adding sync and hoping for no power cut during critical section
This change introduces the last solution that is the simplest. It
reduces time during which things may go wrong from ~35 seconds to
probably less than a second. Of course it applies only to IO operations
performed before /etc/init.d/boot . It's probably the stage when the
most new files get created.
All later changes are usually done using smarter C apps (e.g. busybox or
uci) that creates tmp files and uses rename() that is expected to be
atomic.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Modems used in ZTE mobile broadband routers require to query the data
session status using the same CID as one used to establish the session,
otherwise they will report the session as "disconnected" despite
reporting correct PDH in previous step. Without this change, IPv6
connection on these modems doesn't establish properly. In IPv4 this bug
is present as well, but for some reason querying of IPv4 status works
using temporary CID, this however seems noncompliant with QMI
specifications, so fix it as well.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Previously libxt_socket.so was included in iptables-mod-tproxy. It was
missed out when trying to make kmod-ipt-socket and kmod-ipt-tproxy
separate packages
Fixes: 4f443c88 ("netfilter: separate packages for kmod-ipt-socket and kmod-ipt-tproxy")
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This patch adds the device-specific configuration to u-boot-envtools for
I-O DATA BSH-G24MB switch.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This switches the iwlwifi-firmware-ax200 file to API version 66, this is
the most recent version supported by our driver.
The following files used in OpenWrt changed:
amdgpu-firmware/lib/firmware/amdgpu/yellow_carp_dmcub.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_010a.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_010b.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_0303.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf_010a.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf_010b.bin
ar3k-firmware/lib/firmware/qca/nvm_usb_00130201_gf_0303.bin
ar3k-firmware/lib/firmware/qca/rampatch_usb_00130200.bin
ar3k-firmware/lib/firmware/qca/rampatch_usb_00130201.bin
iwlwifi-firmware-ax200/lib/firmware/iwlwifi-cc-a0-66.ucode
iwlwifi-firmware-ax210/lib/firmware/iwlwifi-ty-a0-gf-a0-66.ucode
iwlwifi-firmware-ax210/lib/firmware/iwlwifi-ty-a0-gf-a0.pnvm
iwlwifi-firmware-iwl9000/lib/firmware/iwlwifi-9000-pu-b0-jf-b0-46.ucode
iwlwifi-firmware-iwl9260/lib/firmware/iwlwifi-9260-th-b0-jf-b0-46.ucode
rtl8822ce-firmware/lib/firmware/rtw88/rtw8822c_fw.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
3276aed81c73 move run_cmd() to main.c
558eabc13c64 map: move dns host based lookup code to a separate function
6ff06d66c36c dns: add code for snooping dns packets
a78bd43c4a54 ubus: remove dnsmasq subscriber
9773ffa70f1f map: process dns patterns in the order in which they were defined
f13b67c9a786 dns: allow limiting dns entry matching to cname name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds the new tc-bpf variant and removes libxtables dependency from
the tc-tiny variant. The tc-full variant stays like before and contains
everything.
This allows to use tc without libxtables.
The variants have the following sizes:
root@OpenWrt:/# ls -al /usr/libexec/tc-*
-rwxr-xr-x 1 root root 282453 Mar 1 21:55 /usr/libexec/tc-bpf
-rwxr-xr-x 1 root root 282533 Mar 1 21:55 /usr/libexec/tc-full
-rwxr-xr-x 1 root root 266037 Mar 1 21:55 /usr/libexec/tc-tiny
They are linking the following shared libraries:
root@OpenWrt:/# ldd /usr/libexec/tc-tiny
/lib/ld-musl-mips-sf.so.1 (0x77d6e000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77d4a000)
libc.so => /lib/ld-musl-mips-sf.so.1 (0x77d6e000)
root@OpenWrt:/# ldd /usr/libexec/tc-bpf
/lib/ld-musl-mips-sf.so.1 (0x77da6000)
libbpf.so.0 => /usr/lib/libbpf.so.0 (0x77d60000)
libelf.so.1 => /usr/lib/libelf.so.1 (0x77d3e000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77d1a000)
libc.so => /lib/ld-musl-mips-sf.so.1 (0x77da6000)
libz.so.1 => /usr/lib/libz.so.1 (0x77cf6000)
root@OpenWrt:/# ldd /usr/libexec/tc-full
/lib/ld-musl-mips-sf.so.1 (0x77de8000)
libbpf.so.0 => /usr/lib/libbpf.so.0 (0x77da2000)
libelf.so.1 => /usr/lib/libelf.so.1 (0x77d80000)
libxtables.so.12 => /usr/lib/libxtables.so.12 (0x77d66000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x77d42000)
libc.so => /lib/ld-musl-mips-sf.so.1 (0x77de8000)
libz.so.1 => /usr/lib/libz.so.1 (0x77d1e000)
This is based on a patch from Tiago Gaspar.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add U-Boot environment settings for Ruijie RG-EW3200GX PRO to allow
users to access the bootloader environment using fw_printenv/fw_setenv
while running OpenWrt.
Signed-off-by: Langhua Ye <y1248289414@outlook.com>
Steps to reproduce:
1. Insert NVMe disk with a reduction to Turris Omnia
2. Go to U-boot
3. Run these two commands:
a) ``nvme scan``
b) ``nvme detail``
4. Wait for crash
This is backported from U-boot upstream repository.
It should be included in the upcoming release - 2022.04 [1].
It was tested on Turris Omnia, mvebu, cortex-a9, OpenWrt master.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20211209100639.21530-1-pali@kernel.org/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[Export the patch from U-Boot git]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Without PKG_RELEASE, it's impossible to trigger package updates when
changing files included in the package that are not in the qosify git
repository.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Felix Fietkau <nbd@nbd.name>
The /tmp directory is mounted as tmpfs. The tmpfs filesystem is backed by
anonymous memory, which means it can be swapped out at any time, if there is
memory pressure [1]. For this reason, a zram swap device is a much better
choice than mounting /tmp on zram, since it's able to compress all anonymous
memory, and not just the memory assigned to /tmp. We already have the zram-swap
package for this specific purpose, which means procd's tmp-on-zram is both
redundant and more limited.
A follow-up patch will remove support for mounting /tmp in zram from procd
itself.
[1] https://www.kernel.org/doc/Documentation/filesystems/tmpfs.txt
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Update to the latest upstream version. In this version there is a new
tool with which you can convert ipsets into nftables sets. Since we are
now using nftables as default firewall, this could be a useful tool for
porting ipsets to nftables sets.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
iptables-nft doesn't depend on libip{4,6}tc, so move
libiptext* libs in their own packages to clean up dependencies
Rename libxtables-nft to libiptext-nft
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Using PROVIDES allows to have other packages continue to
depend on iptables and users to pick between legacy and nft
version.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
'iptables-mod-' can be used directly by firewall3, by
iptables and by iptables-nft. They are not linked to
iptables but to libxtables, so fix the dependencies to allow
to remove iptables(-legacy)
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
libxtables doesn't depend on libnftnl, iptables-nft does,
so move the dependency to not pull libnftnl with firewall3/iptables-legacy
Also libxtables-nft depends on IPTABLES_NFTABLES
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Debians' changelog by Henrique de Moraes Holschuh <hmh@debian.org>:
* upstream changelog: new upstream datafile 20220207
* Mitigates (*only* when loaded from UEFI firmware through the FIT)
CVE-2021-0146, INTEL-SA-00528: VT-d privilege escalation through
debug port, on Pentium, Celeron and Atom processors with signatures
0x506c9, 0x506ca, 0x506f1, 0x706a1, 0x706a8
https://github.com/intel/Intel-Linux-Processor-Microcode-Data-Files/issues/57#issuecomment-1036363145
* Mitigates CVE-2021-0127, INTEL-SA-00532: an unexpected code breakpoint
may cause a system hang, on many processors.
* Mitigates CVE-2021-0145, INTEL-SA-00561: information disclosure due
to improper sanitization of shared resources (fast-store forward
predictor), on many processors.
* Mitigates CVE-2021-33120, INTEL-SA-00589: out-of-bounds read on some
Atom Processors may allow information disclosure or denial of service
via network access.
* Fixes critical errata (functional issues) on many processors
* Adds a MSR switch to enable RAPL filtering (default off, once enabled
it can only be disabled by poweroff or reboot). Useful to protect
SGX and other threads from side-channel info leak. Improves the
mitigation for CVE-2020-8694, CVE-2020-8695, INTEL-SA-00389 on many
processors.
* Disables TSX in more processor models.
* Fixes issue with WBINDV on multi-socket (server) systems which could
cause resets and unpredictable system behavior.
* Adds a MSR switch to 10th and 11th-gen (Ice Lake, Tiger Lake, Rocket
Lake) processors, to control a fix for (hopefully rare) unpredictable
processor behavior when HyperThreading is enabled. This MSR switch
is enabled by default on *server* processors. On other processors,
it needs to be explicitly enabled by an updated UEFI/BIOS (with added
configuration logic). An updated operating system kernel might also
be able to enable it. When enabled, this fix can impact performance.
* Updated Microcodes:
sig 0x000306f2, pf_mask 0x6f, 2021-08-11, rev 0x0049, size 38912
sig 0x000306f4, pf_mask 0x80, 2021-05-24, rev 0x001a, size 23552
sig 0x000406e3, pf_mask 0xc0, 2021-04-28, rev 0x00ec, size 105472
sig 0x00050653, pf_mask 0x97, 2021-05-26, rev 0x100015c, size 34816
sig 0x00050654, pf_mask 0xb7, 2021-06-16, rev 0x2006c0a, size 43008
sig 0x00050656, pf_mask 0xbf, 2021-08-13, rev 0x400320a, size 35840
sig 0x00050657, pf_mask 0xbf, 2021-08-13, rev 0x500320a, size 36864
sig 0x0005065b, pf_mask 0xbf, 2021-06-04, rev 0x7002402, size 28672
sig 0x00050663, pf_mask 0x10, 2021-06-12, rev 0x700001c, size 28672
sig 0x00050664, pf_mask 0x10, 2021-06-12, rev 0xf00001a, size 27648
sig 0x00050665, pf_mask 0x10, 2021-09-18, rev 0xe000014, size 23552
sig 0x000506c9, pf_mask 0x03, 2021-05-10, rev 0x0046, size 17408
sig 0x000506ca, pf_mask 0x03, 2021-05-10, rev 0x0024, size 16384
sig 0x000506e3, pf_mask 0x36, 2021-04-29, rev 0x00ec, size 108544
sig 0x000506f1, pf_mask 0x01, 2021-05-10, rev 0x0036, size 11264
sig 0x000606a6, pf_mask 0x87, 2021-12-03, rev 0xd000331, size 291840
sig 0x000706a1, pf_mask 0x01, 2021-05-10, rev 0x0038, size 74752
sig 0x000706a8, pf_mask 0x01, 2021-05-10, rev 0x001c, size 75776
sig 0x000706e5, pf_mask 0x80, 2021-05-26, rev 0x00a8, size 110592
sig 0x000806a1, pf_mask 0x10, 2021-09-02, rev 0x002d, size 34816
sig 0x000806c1, pf_mask 0x80, 2021-08-06, rev 0x009a, size 109568
sig 0x000806c2, pf_mask 0xc2, 2021-07-16, rev 0x0022, size 96256
sig 0x000806d1, pf_mask 0xc2, 2021-07-16, rev 0x003c, size 101376
sig 0x000806e9, pf_mask 0x10, 2021-04-28, rev 0x00ec, size 104448
sig 0x000806e9, pf_mask 0xc0, 2021-04-28, rev 0x00ec, size 104448
sig 0x000806ea, pf_mask 0xc0, 2021-04-28, rev 0x00ec, size 103424
sig 0x000806eb, pf_mask 0xd0, 2021-04-28, rev 0x00ec, size 104448
sig 0x000806ec, pf_mask 0x94, 2021-04-28, rev 0x00ec, size 104448
sig 0x00090661, pf_mask 0x01, 2021-09-21, rev 0x0015, size 20480
sig 0x000906c0, pf_mask 0x01, 2021-08-09, rev 0x2400001f, size 20480
sig 0x000906e9, pf_mask 0x2a, 2021-04-29, rev 0x00ec, size 106496
sig 0x000906ea, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 102400
sig 0x000906eb, pf_mask 0x02, 2021-04-28, rev 0x00ec, size 104448
sig 0x000906ec, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 103424
sig 0x000906ed, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 103424
sig 0x000a0652, pf_mask 0x20, 2021-04-28, rev 0x00ec, size 93184
sig 0x000a0653, pf_mask 0x22, 2021-04-28, rev 0x00ec, size 94208
sig 0x000a0655, pf_mask 0x22, 2021-04-28, rev 0x00ee, size 94208
sig 0x000a0660, pf_mask 0x80, 2021-04-28, rev 0x00ea, size 94208
sig 0x000a0661, pf_mask 0x80, 2021-04-29, rev 0x00ec, size 93184
sig 0x000a0671, pf_mask 0x02, 2021-08-29, rev 0x0050, size 102400
* Removed Microcodes:
sig 0x00080664, pf_mask 0x01, 2021-02-17, rev 0xb00000f, size 130048
sig 0x00080665, pf_mask 0x01, 2021-02-17, rev 0xb00000f, size 130048
* update .gitignore and debian/.gitignore.
Add some missing items from .gitignore and debian/.gitignore.
* ucode-blacklist: do not late-load 0x406e3 and 0x506e3.
When the BIOS microcode is older than revision 0x7f (and perhaps in some
other cases as well), the latest microcode updates for 0x406e3 and
0x506e3 must be applied using the early update method. Otherwise, the
system might hang. Also: there must not be any other intermediate
microcode update attempts [other than the one done by the BIOS itself],
either. It must go from the BIOS microcode update directly to the
latest microcode update.
* source: update symlinks to reflect id of the latest release, 20220207
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
iucode-tool/host is used by intel-microcode to manipulate with
microcode.bin file. iucode-tool requires cpuid.h at compile time
for autodection feature, but non-x86 build hosts does not have
this header file (e.g. ubuntu 20.04 aarch64) or this header
generates compile time error (#error macro) (e.g. macos arm64).
This patch provides compat cpuid.h to build iucode-tool/host on
non-x86 linux hosts and macos. CPU autodectection is not required
for intel-microcode package build so compat cpuid.h is ok for
OpenWrt purposes.
glibc and argp lib are not present in macos so iucode-tool/host
build fails. This patch adds argp-standalone/host as build
dependency if host os is macos.
Generated ucode (intel-microcode package) is exactly the same on
Linux x86_64 (Ubuntu 20.04), Linux aarch64 (Ubuntu 20.04) and
Darwin arm64 (MacOS 11.6) build hosts.
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
This patch adds host-compile ability to argp-standalone for build
hosts without glibc and argp lib, e.g. MacOS.
iucode-tool/host can not be built on MacOS due to lack of argp.
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
<https://github.com/ARMmbed/mbedtls/releases/tag/v2.28.0>
"Mbed TLS 2.28 is a long-time support branch.
It will be supported with bug-fixes and security
fixes until end of 2024."
<https://github.com/ARMmbed/mbedtls/blob/development/BRANCHES.md>
"Currently, the only supported LTS branch is: mbedtls-2.28.
For a short time we also have the previous LTS, which has
recently ended its support period, mbedtls-2.16.
This branch will move into the archive namespace around the
time of the next release."
this will also add support for uacme ualpn support.
size changes
221586 libmbedtls12_2.28.0-1_mips_24kc.ipk
182742 libmbedtls12_2.16.12-1_mips_24kc.ipk
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
(remark about 2.16's EOS, slightly reworded)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ZTE MF286A and MF286R are indoor LTE category 6/7 CPE router with simultaneous
dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit
Ethernet switch, FXS and external USB 2.0 port.
Hardware highlights:
- CPU: QCA9563 SoC at 775MHz,
- RAM: 128MB DDR2,
- NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only,
- NAND Flash: W25N01GV 128MB SPI NAND-Flash, for all other data,
- Wi-Fi 5GHz: QCA9886 2x2 MIMO 802.11ac Wave2 radio,
- WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio,
- Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port,
- WWAN:
[MF286A] MDM9230-based category 6 internal LTE modem
[MF286R] PXA1826-based category 7 internal LTE modem
in extended mini-PCIE form factor, with 3 internal antennas and
2 external antenna connections, single mini-SIM slot.
- FXS: one external ATA port (handled entirely by modem part) with two
physical connections in parallel,
- USB: Single external USB 2.0 port,
- Switches: power switch, WPS, Wi-Fi and reset buttons,
- LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery,
Signal state) handled entirely by modem. 4 link status LEDs handled by
the switch on the backside.
- Battery: 3Ah 1-cell Li-Ion replaceable battery, with charging and
monitoring handled by modem.
- Label MAC device: eth0
The device shares many components with previous model, MF286, differing
mostly by a Wave2 5GHz radio, flash layout and internal LED color.
In case of MF286A, the modem is the same as in MF286. MF286R uses a
different modem based on Marvell PXA1826 chip.
Internal modem of MF286A is supported via uqmi, MF286R modem isn't fully
supported, but it is expected to use comgt-ncm for connection, as it
uses standard 3GPP AT commands for connection establishment.
Console connection: connector X2 is the console port, with the following
pinout, starting from pin 1, which is the topmost pin when the board is
upright:
- VCC (3.3V). Do not use unless you need to source power for the
converer from it.
- TX
- RX
- GND
Default port configuration in U-boot as well as in stock firmware is
115200-8-N-1.
Installation:
Due to different flash layout from stock firmware, sysupgrade from
within stock firmware is impossible, despite it's based on QSDK which
itself is based on OpenWrt.
STEP 0: Stock firmware update:
As installing OpenWrt cuts you off from official firmware updates for
the modem part, it is recommended to update the stock firmware to latest
version before installation, to have built-in modem at the latest firmware
version.
STEP 1: gaining root shell:
Method 1:
This works if busybox has telnetd compiled in the binary.
If this does not work, try method 2.
Using well-known exploit to start telnetd on your router - works
only if Busybox on stock firmware has telnetd included:
- Open stock firmware web interface
- Navigate to "URL filtering" section by going to "Advanced settings",
then "Firewall" and finally "URL filter".
- Add an entry ending with "&&telnetd&&", for example
"http://hostname/&&telnetd&&".
- telnetd will immediately listen on port 4719.
- After connecting to telnetd use "admin/admin" as credentials.
Method 2:
This works if busybox does not have telnetd compiled in. Notably, this
is the case in DNA.fi firmware.
If this does not work, try method 3.
- Set IP of your computer to 192.168.0.22. (or appropriate subnet if
changed)
- Have a TFTP server running at that address
- Download MIPS build of busybox including telnetd, for example from:
https://busybox.net/downloads/binaries/1.21.1/busybox-mips
and put it in it's root directory. Rename it as "telnetd".
- As previously, login to router's web UI and navigate to "URL
filtering"
- Using "Inspect" feature, extend "maxlength" property of the input
field named "addURLFilter", so it looks like this:
<input type="text" name="addURLFilter" id="addURLFilter" maxlength="332"
class="required form-control">
- Stay on the page - do not navigate anywhere
- Enter "http://aa&zte_debug.sh 192.168.0.22 telnetd" as a filter.
- Save the settings. This will download the telnetd binary over tftp and
execute it. You should be able to log in at port 23, using
"admin/admin" as credentials.
Method 3:
If the above doesn't work, use the serial console - it exposes root shell
directly without need for login. Some stock firmwares, notably one from
finnish DNA operator lack telnetd in their builds.
STEP 2: Backing up original software:
As the stock firmware may be customized by the carrier and is not
officially available in the Internet, IT IS IMPERATIVE to back up the
stock firmware, if you ever plan to returning to stock firmware.
It is highly recommended to perform backup using both methods, to avoid
hassle of reassembling firmware images in future, if a restore is
needed.
Method 1: after booting OpenWrt initramfs image via TFTP:
PLEASE NOTE: YOU CANNOT DO THIS IF USING INTERMEDIATE FIRMWARE FOR INSTALLATION.
- Dump stock firmware located on stock kernel and ubi partitions:
ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin
ssh root@192.168.1.1: cat /dev/mtd9 > mtd9_ubi.bin
And keep them in a safe place, should a restore be needed in future.
Method 2: using stock firmware:
- Connect an external USB drive formatted with FAT or ext4 to the USB
port.
- The drive will be auto-mounted to /var/usb_disk
- Check the flash layout of the device:
cat /proc/mtd
It should show the following:
mtd0: 000a0000 00010000 "u-boot"
mtd1: 00020000 00010000 "u-boot-env"
mtd2: 00140000 00010000 "reserved1"
mtd3: 000a0000 00020000 "fota-flag"
mtd4: 00080000 00020000 "art"
mtd5: 00080000 00020000 "mac"
mtd6: 000c0000 00020000 "reserved2"
mtd7: 00400000 00020000 "cfg-param"
mtd8: 00400000 00020000 "log"
mtd9: 000a0000 00020000 "oops"
mtd10: 00500000 00020000 "reserved3"
mtd11: 00800000 00020000 "web"
mtd12: 00300000 00020000 "kernel"
mtd13: 01a00000 00020000 "rootfs"
mtd14: 01900000 00020000 "data"
mtd15: 03200000 00020000 "fota"
mtd16: 01d00000 00020000 "firmware"
Differences might indicate that this is NOT a MF286A device but
one of other variants.
- Copy over all MTD partitions, for example by executing the following:
for i in 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15; do cat /dev/mtd$i > \
/var/usb_disk/mtd$i; done
"Firmware" partition can be skipped, it is a concatenation
of "kernel" and "rootfs".
- If the count of MTD partitions is different, this might indicate that
this is not a MF286A device, but one of its other variants.
- (optionally) rename the files according to MTD partition names from
/proc/mtd
- Unmount the filesystem:
umount /var/usb_disk; sync
and then remove the drive.
- Store the files in safe place if you ever plan to return to stock
firmware. This is especially important, because stock firmware for
this device is not available officially, and is usually customized by
the mobile providers.
STEP 3: Booting initramfs image:
Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
set your computer's IP address as 192.168.0.22. This is the default
expected by U-boot. You may wish to change that, and alter later
commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:
setenv serverip 192.168.0.22
setenv ipaddr 192.168.0.1
tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286a-initramfs-kernel.bin
bootm 0x81000000
(Replace server IP and router IP as needed). There is no emergency
TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
installation.
Method 2: using initramfs image as temporary boot kernel
This exploits the fact, that kernel and rootfs MTD devices are
consecutive on NAND flash, so from within stock image, an initramfs can
be written to this area and booted by U-boot on next reboot, because it
uses "nboot" command which isn't limited by kernel partition size.
- Download the initramfs-kernel.bin image
- After backing up the previous MTD contents, write the images to the
"firmware" MTD device, which conveniently concatenates "kernel" and
"rootfs" partitions that can fit the initramfs image:
nandwrite -p /dev/<firmware-mtd> \
/var/usb_disk/openwrt-ath79-zte_mf286a-initramfs-kernel.bin
- If write is OK, reboot the device, it will reboot to OpenWrt
initramfs:
reboot -f
- After rebooting, SSH into the device and use sysupgrade to perform
proper installation.
Method 3: using built-in TFTP recovery (LAST RESORT):
- With that method, ensure you have complete backup of system's NAND
flash first. It involves deliberately erasing the kernel.
- Download "-initramfs-kernel.bin" image for the device.
- Prepare the recovery image by prepending 8MB of zeroes to the image,
and name it root_uImage:
dd if=/dev/zero of=padding.bin bs=8M count=1
cat padding.bin openwrt-ath79-nand-zte_mf286a-initramfs-kernel.bin >
root_uImage
- Set up a TFTP server at 192.0.0.1/8. Router will use random address
from that range.
- Put the previously generated "root_uImage" into TFTP server root
directory.
- Deliberately erase "kernel" partition" using stock firmware after
taking backup. THIS IS POINT OF NO RETURN.
- Restart the device. U-boot will attempt flashing the recovery
initramfs image, which will let you perform actual installation using
sysupgrade. This might take a considerable time, sometimes the router
doesn't establish Ethernet link properly right after booting. Be
patient.
- After U-boot finishes flashing, the LEDs of switch ports will all
light up. At this moment, perform power-on reset, and wait for OpenWrt
initramfs to finish booting. Then proceed to actual installation.
STEP 4: Actual installation:
- Set your computer IP to 192.168.1.22/24
- scp the sysupgrade image to the device:
scp openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin \
root@192.168.1.1:/tmp/
- ssh into the device and execute sysupgrade:
sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin
- Wait for router to reboot to full OpenWrt.
STEP 5: WAN connection establishment
Since the router is equipped with LTE modem as its main WAN interface, it
might be useful to connect to the Internet right away after
installation. To do so, please put the following entries in
/etc/config/network, replacing the specific configuration entries with
one needed for your ISP:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option auth '<auth>' # As required, usually 'none'
option pincode '<pin>' # If required by SIM
option apn '<apn>' # As required by ISP
option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6'
For example, the following works for most polish ISPs
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option auth 'none'
option apn 'internet'
option pdptype 'ipv4'
The required minimum is:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
In this case, the modem will use last configured APN from stock
firmware - this should work out of the box, unless your SIM requires
PIN which can't be switched off.
If you have build with LuCI, installing luci-proto-qmi helps with this
task.
Restoring the stock firmware:
Preparation:
If you took your backup using stock firmware, you will need to
reassemble the partitions into images to be restored onto the flash. The
layout might differ from ISP to ISP, this example is based on generic stock
firmware
The only partitions you really care about are "web", "kernel", and
"rootfs". These are required to restore the stock firmware through
factory TFTP recovery.
Because kernel partition was enlarged, compared to stock
firmware, the kernel and rootfs MTDs don't align anymore, and you need
to carve out required data if you only have backup from stock FW:
- Prepare kernel image
cat mtd12_kernel.bin mtd13_rootfs.bin > owrt_kernel.bin
truncate -s 4M owrt_kernel_restore.bin
- Cut off first 1MB from rootfs
dd if=mtd13_rootfs.bin of=owrt_rootfs.bin bs=1M skip=1
- Prepare image to write to "ubi" meta-partition:
cat mtd6_reserved2.bi mtd7_cfg-param.bin mtd8_log.bin mtd9_oops.bin \
mtd10_reserved3.bin mtd11_web.bin owrt_rootfs.bin > \
owrt_ubi_ubi_restore.bin
You can skip the "fota" partition altogether,
it is used only for stock firmware update purposes and can be overwritten
safely anyway. The same is true for "data" partition which on my device
was found to be unused at all. Restoring mtd5_cfg-param.bin will restore
the stock firmware configuration you had before.
Method 1: Using initramfs:
This method is recmmended if you took your backup from within OpenWrt
initramfs, as the reassembly is not needed.
- Boot to initramfs as in step 3:
- Completely detach ubi0 partition using ubidetach /dev/ubi0_0
- Look up the kernel and ubi partitions in /proc/mtd
- Copy over the stock kernel image using scp to /tmp
- Erase kernel and restore stock kernel:
(scp mtd4_kernel.bin root@192.168.1.1:/tmp/)
mtd write <kernel_mtd> mtd4_kernel.bin
rm mtd4_kernel.bin
- Copy over the stock partition backups one-by-one using scp to /tmp, and
restore them individually. Otherwise you might run out of space in
tmpfs:
(scp mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/)
mtd write <ubiconcat0_mtd> mtd3_ubiconcat0.bin
rm mtd3_ubiconcat0.bin
(scp mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/)
mtd write <ubiconcat1_mtd> mtd5_ubiconcat1.bin
rm mtd5_ubiconcat1.bin
- If the write was correct, force a device reboot with
reboot -f
Method 2: Using live OpenWrt system (NOT RECOMMENDED):
- Prepare a USB flash drive contatining MTD backup files
- Ensure you have kmod-usb-storage and filesystem driver installed for
your drive
- Mount your flash drive
mkdir /tmp/usb
mount /dev/sda1 /tmp/usb
- Remount your UBI volume at /overlay to R/O
mount -o remount,ro /overlay
- Write back the kernel and ubi partitions from USB drive
cd /tmp/usb
mtd write mtd4_kernel.bin /dev/<kernel_mtd>
mtd write mtd9_ubi.bin /dev/<kernel_ubi>
- If everything went well, force a device reboot with
reboot -f
Last image may be truncated a bit due to lack of space in RAM, but this will happen over "fota"
MTD partition which may be safely erased after reboot anyway.
Method 3: using built-in TFTP recovery:
This method is recommended if you took backups using stock firmware.
- Assemble a recovery rootfs image from backup of stock partitions by
concatenating "web", "kernel", "rootfs" images dumped from the device,
as "root_uImage"
- Use it in place of "root_uImage" recovery initramfs image as in the
TFTP pre-installation method.
Quirks and known issuesa
- It was observed, that CH340-based USB-UART converters output garbage
during U-boot phase of system boot. At least CP2102 is known to work
properly.
- Kernel partition size is increased to 4MB compared to stock 3MB, to
accomodate future kernel updates - at this moment OpenWrt 5.10 kernel
image is at 2.5MB which is dangerously close to the limit. This has no
effect on booting the system - but keep that in mind when reassembling
an image to restore stock firmware.
- uqmi seems to be unable to change APN manually, so please use the one
you used before in stock firmware first. If you need to change it,
please use protocok '3g' to establish connection once, or use the
following command to change APN (and optionally IP type) manually:
echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0
- The only usable LED as a "system LED" is the blue debug LED hidden
inside the case. All other LEDs are controlled by modem, on which the
router part has some influence only on Wi-Fi LED.
- Wi-Fi LED currently doesn't work while under OpenWrt, despite having
correct GPIO mapping. All other LEDs are controlled by modem,
including this one in stock firmware. GPIO19, mapped there only acts
as a gate, while the actual signal source seems to be 5GHz Wi-Fi
radio, however it seems it is not the LED exposed by ath10k as
ath10k-phy0.
- GPIO5 used for modem reset is a suicide switch, causing a hardware
reset of whole board, not only the modem. It is attached to
gpio-restart driver, to restart the modem on reboot as well, to ensure
QMI connectivity after reboot, which tends to fail otherwise.
- Modem, as in MF283+, exposes root shell over ADB - while not needed
for OpenWrt operation at all - have fun lurking around.
The same modem module is used as in older MF286.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Both struct net_device_path_ctx and struct net_device_path
are not available in 5.4. This causes an build error on the
bcm63xx target.
|mac80211/driver-ops.h: In function 'drv_net_fill_forward_path':
|driver-ops.h:1502:57: error: passing argument 4 of
|'local->ops->net_fill_forward_path' from incompatible pointer type
| [-Werror=incompatible-pointer-types]
| 1502 | ctx, path);
| | ^~~
| | |
| | struct net_device_path_ctx *
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Package the ability to log kernel crashes to 'ramoops' pstore
files into RAM in /sys/fs/pstore
Reference to the ramoops admin guide in upstream Linux:
https://www.kernel.org/doc/html/v5.10/admin-guide/ramoops.html
The files in RAM survive a warm reboot, but not a cold reboot.
Note: kmod-ramoops selects kmod-pstore and kmod-reed-solomon.
The feature can be used by selecting the kmod-ramoops and
adding a ramoops reserved-memory definition to the device DTS.
Example from R7800:
reserved-memory {
rsvd@5fe00000 {
reg = <0x5fe00000 0x200000>;
reusable;
};
ramoops@42100000 {
compatible = "ramoops";
reg = <0x42100000 0x40000>;
record-size = <0x4000>;
console-size = <0x4000>;
ftrace-size = <0x4000>;
pmsg-size = <0x4000>;
};
};
If no definition has been made in DTS, no crash log is stored
for the device.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(added CONFIG_EFI_VARS_PSTORE disable)
Previously, grub2 was hardcoded to always look on "hd0" for the
kernel.
This works well when the system only had a single disk.
But if there was a second disk/stick present, it may have look
on the wrong drive because of enumeration races.
This patch utilizes grub2 search function to look for a filesystem
with the label "kernel". This works thanks to existing setup in
scripts/gen_image_generic.sh. Which sets the "kernel" label on
both the fat and ext4 filesystem variants.
Signed-off-by: Jax Jiang <jax.jiang.007@gmail.com>
Suggested-by: Alberto Bursi <bobafetthotmail@gmail.com> (MX100 WA)
(word wrapped, slightly rewritten commit message, removed MX100 WA)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
AT91Bootstrap version 4 is available only for SAM9X60, SAMA5D2, SAMA5D3,
SAMA5D4, SAMA7G5. Thus use v4.0.1 for the above targets and v3.10.4 for
the rest of them. With the switch to v4 AT91Bootstrap binaries are now
on build/binaries. Take also this into account. Also, patches directory
is not needed anymore with the version update.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
In the default shadow file, as visible in the failsafe mode, the user
root has value of `0` set in the 3rd field, the date of last password
change. This setting means that the password needs to be changed the
next time the user will log in the system. `dropbear` server is ignoring
this setting but `openssh-server` tries to enforce it and fails in the
failsafe mode because the rootfs is R/O.
Disable the password aging feature for user root by setting the 3rd
filed empty.
Signed-off-by: Rucke Teg <rucketeg@protonmail.com>
Enable both the hunting-and-pecking loop and hash-to-element mechanisms
by default in OpenWRT with SAE.
Commercial Wi-Fi solutions increasingly frequently now ship with both
hunting-and-pecking and hash-to-element (H2E) enabled by default as this
is more secure and more performant than offering hunting-and-pecking
alone for H2E capable clients.
The hunting and pecking loop mechanism is inherently fragile and prone to
timing-based side channels in its design and is more computationally
intensive to perform. Hash-to-element (H2E) is its long-term
replacement to address these concerns.
For clients that only support the hunting-and-pecking loop mechanism,
this is still available to use by default.
For clients that in addition support, or were to require, the
hash-to-element (H2E) mechanism, this is then available for use.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Backport fix for API breakage of SSL_get_verify_result() introduced in
v5.1.1-stable. In v4.8.1-stable SSL_get_verify_result() used to return
X509_V_OK when used on LE powered sites or other sites utilizing
relaxed/alternative cert chain validation feature. After an update to
v5.1.1-stable that API calls started returning X509_V_ERR_INVALID_CA
error and thus rendered all such connection attempts imposible:
$ docker run -it openwrt/rootfs:x86_64-21.02.2 sh -c "wget https://letsencrypt.org"
Downloading 'https://letsencrypt.org'
Connecting to 18.159.128.50:443
Connection error: Invalid SSL certificate
Fixes: #9283
References: https://github.com/wolfSSL/wolfssl/issues/4879
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Not all targets create /var/lock or touch /var/lock/fw_printenv.lock in
their platform.sh. This is problematic as fw_printenv then fails in
case /var/lock/fw_printenv.lock has not been created by previous calls
to fw_printenv/fw_setenv before sysupgrade is run.
Targets using fw_printenv/fw_setenv during sysupgrade:
* ath79/*
* ipq40xx/*
* ipq806x/*
* kirkwood/*
* layerscape/*
* mediatek/mt7622
* mvebu/*
* ramips/*
* realtek/*
Targets currently using additional steps in /lib/upgrade/platform.sh
to make sure /var/lock/fw_printenv.lock (or at least /var/lock)
actually exists:
* ath79/* (openmesh devices)
* ipq40xx/* (linksys devices)
* ipq806x/* (linksys devices)
* kirkwood/* (linksys devices)
* layerscape/*
* mvebu/cortexa9 (linksys devices)
Given that accessing the U-Boot environment during sysupgrade is not
uncommon and the situation across targets is currently quite diverse,
just make sure both tools as well fw_env.config are always copied to
the ramdisk used for sysupgrade. Also make sure /var/lock always
exists.
This now allows to remove copying of fw_printenv/fw_setenv as well as
fw_env.config, creation of /var/lock or even /var/lock/fw_printenv.lock
from lib/upgrade/platform.sh or files included there.
As the same applies also to 'fwtool' which is used by generic eMMC
sysupgrade, also always copy that to ramdisk.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This uses uci to configure engines, by generating a list of enabled
engines in /var/etc/ssl/engines.cnf from engines configured in
/etc/config/openssl:
config engine 'devcrypto'
option enabled '1'
Currently the only options implemented are 'enabled', which defaults to
true and enables the named engine, and the 'force' option, that enables
the engine even if the init script thinks the engine does not exist.
The existence test is to check for either a configuration file
/etc/ssl/engines.cnf.d/%ENGINE%.cnf, or a shared object file
/usr/lib/engines-1.1/%ENGINE%.so.
The engine list is generated by an init script which is set to run after
'log' because it informs the engines being enabled or skipped. It
should run before any service using OpenSSL as the crypto library,
otherwise the service will not use any engine.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This enables an engine during its package's installation, by adding it
to the engines list in /etc/ssl/engines.cnf.d/engines.cnf.
The engine build system was reworked, with the addition of an engine.mk
file that groups some of the engine packages' definitions, and could be
used by out of tree engines as well.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This changes the configuration of engines from the global openssl.cnf to
files in the /etc/ssl/engines.cnf.d directory. The engines.cnf file has
the list of enabled engines, while each engine has its own configuration
file installed under /etc/ssl/engines.cnf.d.
Patches were refreshed with --zero-commit.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
100-ddr-marvell-a38x-fix-BYTE_HOMOGENEOUS_SPLIT_OUT-deci.patch [1]:
SoC Marvell A38x is used in Turris Omnia, and we thought that with recent
fiddling around DDR training to fix it once for all, there were
reproduced the issue in the upcoming new revision Turris Omnia boards.
101-arm-mvebu-spl-Add-option-to-reset-the-board-on-DDR-t.patch [2]:
This is useful when some board may occasionally fail with DDR training,
and it adds the option to reset the board on the DDR training failure
102-arm-mvebu-turris_omnia-Reset-the-board-immediately-o.patch [3]:
This enables the option CONFIG_DDR_RESET_ON_TRAINING_FAILURE (added by
101 patch), so the Turris Omnia board is restarted immediately, and it
does not require to reset the board manually or wait 120s for MCU to
reset the board
[1] https://patchwork.ozlabs.org/project/uboot/patch/20220217000837.13003-1-kabel@kernel.org/
[2] https://patchwork.ozlabs.org/project/uboot/patch/20220217000849.13028-1-kabel@kernel.org/
[3] https://patchwork.ozlabs.org/project/uboot/patch/20220217000849.13028-2-kabel@kernel.org/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This commit adds the following package compile options.
CONFIG_PACKAGE_RTW88_DEBGUG:
Compile the driver with additional debug logging output
CONFIG_PACKAGE_RTW88_DEBGUGFS:
Add the possibility to map information about the driver rtw88 into
debugfs.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Contains following changes:
136006b88826 cmake: fix usage of implicit library and include paths
bc0e84d689e2 netifd: interface-ip: don't set fib6 policies if ipv6 disabled
Signed-off-by: Petr Štetiar <ynezz@true.cz>
e061299 wireless-regdb: Raise DFS TX power limit to 250 mW (24 dBm) for the US
2ce78ed wireless-regdb: Update regulatory rules for Croatia (HR) on 6GHz
0d39f4c wireless-regdb: Update regulatory rules for South Korea (KR)
acad231 wireless-regdb: Update regulatory rules for France (FR) on 6 and 60 GHz
ea83a82 wireless-regdb: add support for US S1G channels
4408149 wireless-regdb: add 802.11ah bands to world regulatory domain
5f3cadc wireless-regdb: Update regulatory rules for Spain (ES) on 6GHz
e0ac69b Revert "wireless-regdb: Update regulatory rules for South Korea (KR)"
40e5e80 wireless-regdb: Update regulatory rules for South Korea (KR)
e427ff2 wireless-regdb: Update regulatory rules for China (CN)
0970116 wireless-regdb: Update regulatory rules for the Netherlands (NL) on 6GHz
4dac44b wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
package hwmon's lm70.ko. This module supports the
National Semiconductor/TI LM70,LM71,LM74 and
TI TMP121,TMP122,TMP123 and TMP124 chips (all SPI).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
When Kernel 5.10 was enabled for mpc85xx, the kernel once again became too
large upon decompression (>7MB or so) to decompress itself on boot (see
FS#4110[1]).
There have been many attempts to fix booting from a compressed kernel on
the HiveAP-330:
- b683f1c36d ("mpc85xx: Use gzip compressed kernel on HiveAP-330")
- 98089bb8ba ("mpc85xx: Use uncompressed kernel on the HiveAP-330")
- 26cb167a5c ("mpc85xx: Fix Aerohive HiveAP-330 initramfs image")
We can no longer compress the kernel due to size, and the stock bootloader
does not support any other types of compression. Since an uncompressed
kernel no longer fits in the 8MiB kernel partition at 0x2840000, we need to
patch u-boot to autoboot by running variable which isn't set by the
bootloader on each autoboot.
This commit repartitions the HiveAP, requiring a new COMPAT_VERSION,
and uses the DEVICE_COMPAT_MESSAGE to guide the user to patch u-boot,
which changes the variable run on boot to be `owrt_boot`; the user can
then set the value of that variable appropriately.
The following has been documented in the device's OpenWrt wiki page:
<https://openwrt.org/toh/aerohive/hiveap-330>. Please look there
first/too for more information.
The from-stock and upgrade from a previous installation now becomes:
0) setup a network with a dhcp server and a tftp server at serverip
(192.168.1.101) with the initramfs image in the servers root directory.
1) Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted. If the password
doesn't work. Try reseting the device by pressing and holding the reset
button with the stock OS.
2) Once in U-Boot, set the new owrt_boot and tftp+boot the initramfs image:
Use copy and paste!
# fw_setenv owrt_boot 'setenv bootargs \"console=ttyS0,$baudrate\";bootm 0xEC040000 - 0xEC000000'
# save
# dhcp
# setenv bootargs console=ttyS0,$baudrate
# tftpboot 0x1000000 192.168.1.101:openwrt-mpc85xx-p1020-aerohive_hiveap-330-initramfs-kernel.bin
# bootm
3) Once openwrt booted:
carefully copy and paste this into the root shell. One step at a time
# 3.0 install kmod-mtd-rw from the internet and load it
opkg update; opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=y
# 3.1 create scripts that modifies uboot
cat <<- "EOF" > /tmp/uboot-update.sh
. /lib/functions/system.sh
cp "/dev/mtd$(find_mtd_index 'u-boot')" /tmp/uboot
cp /tmp/uboot /tmp/uboot_patched
ofs=$(strings -n80 -td < /tmp/uboot | grep '^ [0-9]* setenv bootargs.*cp\.l' | cut -f2 -d' ')
for off in $ofs; do
printf "run owrt_boot; " | dd of=/tmp/uboot_patched bs=1 seek=${off} conv=notrunc
done
md5sum /tmp/uboot*
EOF
# 3.2 run the script to do the modification
sh /tmp/uboot-update.sh
# verify that /tmp/uboot and /tmp/uboot_patched are good
#
# my uboot was: (is printed during boot)
# U-Boot 2009.11 (Jan 12 2017 - 00:27:25), Build: jenkins-HiveOS-Honolulu_AP350_Rel-245
#
# d84b45a2e8aca60d630fbd422efc6b39 /tmp/uboot
# 6dc420f24c2028b9cf7f0c62c0c7f692 /tmp/uboot_patched
# 98ebc7e7480ce9148cd2799357a844b0 /tmp/uboot-update.sh <-- just for reference
# 3.3 this produces the /tmp/u-boot_patched file.
mtd write /tmp/uboot_patched u-boot
3) scp over the sysupgrade file to /tmp/ and run sysupgrade to flash OpenWrt:
sysupgrade -n /tmp/openwrt-mpc85xx-p1020-aerohive_hiveap-330-squashfs-sysupgrade.bin
4) after the reboot, you are good to go.
Other notes:
- Note that after this sysupgrade, the AP will be unavailable for 7 minutes
to reformat flash. The tri-color LED does not blink in any way to
indicate this, though there is no risk in interrupting this process,
other than the jffs2 reformat being reset.
- Add a uci-default to fix the compat version. This will prevent updates
from previous versions without going through the installation process.
- Enable CONFIG_MTD_SPLIT_UIMAGE_FW and adjust partitioning to combine
the kernel and rootfs into a single dts partition to maximize storage
space, though in practice the kernel can grow no larger than 16MiB due
to constraints of the older mpc85xx u-boot platform.
- Because of that limit, KERNEL_SIZE has been raised to 16m.
- A .tar.gz of the u-boot source for the AP330 (a.k.a. Goldengate) can
be found here[2].
- The stock-jffs2 partition is also removed to make more space -- this
is possible only now that it is no longer split away from the rootfs.
- the console-override is gone. The device will now get the console
through the bootargs. This has the advantage that you can set a different
baudrate in uboot and the linux kernel will stick with it!
- due to the repartitioning, the partition layout and names got a makeover.
- the initramfs+fdt method is now combined into a MultiImage initramfs.
The separate fdt download is no longer needed.
- added uboot-envtools to the mpc85xx target. All targets have uboot and
this way its available in the initramfs.
[1]: https://bugs.openwrt.org/index.php?do=details&task_id=4110
[2]: magnet:?xt=urn:btih:e53b27006979afb632af5935fa0f2affaa822a59
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
(rewrote parts of the commit message, Initramfs-MultiImage,
dropped bootargs-override, added wiki entry + link, uboot-envtools)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ksmbd is an upstream linux alternative to Samba which is lighterweight
and more performant, especially on underpowered devices.
Moving it here from the packages feed as it is now an upstream kernel
module. Also easier to update as version updates can be coordinated better
The next LTS kernel (5.15) has this included. A depend on kernel < 5.15
will need to be added later.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The 80211r r0kh and r1kh defaults are generated from the md5sum of
"$mobility_domain/$auth_secret". auth_secret is only set when using EAP
authentication, but the default key is used for SAE/PSK as well. In
this case, auth_secret is empty, and the default value of the key can
be computed from the SSID alone.
Fallback to using $key when auth_secret is empty. While at it, rename
the variable holding the generated key from 'key' to 'ft_key', to avoid
clobbering the PSK.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[make ft_key local]
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the STAs extended capabilities to the ubus STA information. This
way, external daemons can be made aware of a STAs capabilities.
This field is of an array type and contains 0 or more bytes of a STAs
advertised extended capabilities.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds support for creation heartbeat led trigger with,
for example, this command:
ucidef_set_led_heartbeat "..." "..." "..."
from /etc/board.d/01_leds.
Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
This module was used solely by Buffalo WZR-HP-G300NH devices
and has become obsolete with the introduction of gpio-cascade.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Adds new kernel module for GPIO controlled multiplexer support.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [missing commit description]
a87d010 uxc: remove unused printf parameter
ad65249 instance: exit in case asprintf() fails
Build with glibc should again work after this commit.
Fixes: e9e61d76fd ("procd: update to git HEAD")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
df1123e uxc: add support for user-defined settings
0272c7c uxc: allow editing settings using 'create'
a839518 uxc: clean up error handling
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
For sysupgrade on NAND/UBI devices there is the U-Boot environment
variable rootfs_data_max which can be used to limit the size of the
rootfs_data volume created on sysupgrade.
This stopped working reliable with recent kernels, probably due to a
race condition when reading the number of free erase blocks from sysfs
just after removing a volume.
Change the script to just try creating rootfs_data with the desired
size and retry with maximum size in case that fails. Hence calculating
the available size in the script can be dropped which works around the
problem.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
'uxc boot' is inteded to be called multiple times, so there is not need
to guard the first call on boot -- the actual code anyway didn't do
that, so just remove it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes the following security problem:
The command-line argument parser in tcpdump before 4.99.0 has a buffer
overflow in tcpdump.c:read_infile(). To trigger this vulnerability the
attacker needs to create a 4GB file on the local filesystem and to
specify the file name as the value of the -F command-line argument of
tcpdump.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
53caa1a fw4: resolve zone layer 2 devices for hw flow offloading
9fe58f5 fw4: rework and fix family inheritance logic
8795296 tests: mocklib: fix infinite recursion in wrapped print()
281b1bc tests: change mocked wan interface type to PPPoE
93b710d tests: mocklib: forward compatibility change
1a94915 fw4: only stage reflection rules if all required addrs are known
5c21714 fw4: add device iifname/oifname matches to DSCP and MARK rules
3eacc97 tests: adjust 01_ruleset test case to latest changes
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
a29bad9 compiler: fix patchlist corruption on switch statement syntax errors
86f0662 lib: change `ord()` to always return single byte value
116a8ce vallist: fix storing/retrieving short strings with 8bit byte value
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When the uci configuration is created automatically during a very early
stage, where no entropy daemon is set up, generating the key directly is
not an option. Therefore we allow to set the private_key to "generate"
and generate the private key directly before the interface is taken up.
Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
Tested-by: Jan-Niklas Burfeind <git@aiyionpri.me>
11adf0c source: convert source objects into proper uc_value_t type
3a49192 treewide: rework function memory model
7edad5c tests: add functional tests for builtin functions
d5003fd lib: fix leaking tokener in uc_json() on parse exception
5d0ecd9 lib: fix infinite loop on empty regexp matches in uc_replace()
3ad57f1 lib: fix infinite loop on empty regexp matches in uc_match()
32d596d lib: fix infinite loop on empty regexp matches in uc_split()
3e3f38d vm: ensure consistent trace output between gcc and clang compiled ucode
3600ded vm: fix leaking function value on call exception
3059295 vm: NULL-initialize pointer to make cppcheck happy
98e59bf source: zero-initialize conversion union to make cppcheck happy
7a65c14 run_tests.sh: change workdir to testcase directory during execution
afec8d7 run_tests.sh: support placing supplemental testcase files
3ada6e0 run_tests.sh: always treat outputs as text data
2cb627f program: rename bytecode load/write functions, track path of executed file
1094ffa lib: fix memory leak in uc_require_ucode()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Xiaomi Mi Router CR6606 is a Wi-Fi6 AX1800 Router with 4 GbE Ports.
Alongside the general model, it has three carrier customized models:
CR6606 (China Unicom), CR6608 (China Mobile), CR6609 (China Telecom)
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256MB DDR3 (ESMT M15T2G16128A)
- Flash: 128MB NAND (ESMT F59L1G81MB)
- Ethernet: 1000Base-T x4 (MT7530 SoC)
- WLAN: 2x2 2.4GHz 574Mbps + 2x2 5GHz 1201Mbps (MT7905DAN + MT7975DN)
- LEDs: System (Blue, Yellow), Internet (Blue, Yellow)
- Buttons: Reset, WPS
- UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
- Power: 12VDC, 1A
Jailbreak Notes:
1. Get shell access.
1.1. Get yourself a wireless router that runs OpenWrt already.
1.2. On the OpenWrt router:
1.2.1. Access its console.
1.2.2. Create and edit
/usr/lib/lua/luci/controller/admin/xqsystem.lua
with the following code (exclude backquotes and line no.):
```
1 module("luci.controller.admin.xqsystem", package.seeall)
2
3 function index()
4 local page = node("api")
5 page.target = firstchild()
6 page.title = ("")
7 page.order = 100
8 page.index = true
9 page = node("api","xqsystem")
10 page.target = firstchild()
11 page.title = ("")
12 page.order = 100
13 page.index = true
14 entry({"api", "xqsystem", "token"}, call("getToken"), (""),
103, 0x08)
15 end
16
17 local LuciHttp = require("luci.http")
18
19 function getToken()
20 local result = {}
21 result["code"] = 0
22 result["token"] = "; nvram set ssh_en=1; nvram commit; sed -i
's/channel=.*/channel=\"debug\"/g' /etc/init.d/dropbear; /etc/init.d/drop
bear start;"
23 LuciHttp.write_json(result)
24 end
```
1.2.3. Browse http://{OWRT_ADDR}/cgi-bin/luci/api/xqsystem/token
It should give you a respond like this:
{"code":0,"token":"; nvram set ssh_en=1; nvram commit; ..."}
If so, continue; Otherwise, check the file, reboot the rout-
er, try again.
1.2.4. Set wireless network interface's IP to 169.254.31.1, turn
off DHCP of wireless interface's zone.
1.2.5. Connect to the router wirelessly, manually set your access
device's IP to 169.254.31.3, make sure
http://169.254.31.1/cgi-bin/luci/api/xqsystem/token
still have a similar result as 1.2.3 shows.
1.3. On the Xiaomi CR660x:
1.3.1. Login to the web interface. Your would be directed to a
page with URL like this:
http://{ROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/web/home#r-
outer
1.3.2. Browse this URL with {STOK} from 1.3.1, {WIFI_NAME}
{PASSWORD} be your OpenWrt router's SSID and password:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/misy-
stem/extendwifi_connect?ssid={WIFI_NAME}&password={PASSWO-
RD}
It should return 0.
1.3.3. Browse this URL with {STOK} from 1.3.1:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/xqsy-
stem/oneclick_get_remote_token?username=xxx&password=xxx&-
nonce=xxx
1.4. Before rebooting, you can now access your CR660x via SSH.
For CR6606, you can calculate your root password by this project:
https://github.com/wfjsw/xiaoqiang-root-password, or at
https://www.oxygen7.cn/miwifi.
The root password for carrier-specific models should be the admi-
nistration password or the default login password on the label.
It is also feasible to change the root password at the same time
by modifying the script from step 1.2.2.
You can treat OpenWrt Router however you like from this point as
long as you don't mind go through this again if you have to expl-
oit it again. If you do have to and left your OpenWrt router unt-
ouched, start from 1.3.
2. There's no official binary firmware available, and if you lose the
content of your flash, no one except Xiaomi can help you.
Dump these partitions in case you need them:
"Bootloader" "Nvram" "Bdata" "crash" "crash_log"
"firmware" "firmware1" "overlay" "obr"
Find the corespond block device from /proc/mtd
Read from read-only block device to avoid misoperation.
It's recommended to use /tmp/syslogbackup/ as destination, since files
would be available at http://{ROUTER_ADDR}/backup/log/YOUR_DUMP
Keep an eye on memory usage though.
3. Since UART access is locked ootb, you should get UART access by modify
uboot env. Otherwise, your router may become bricked.
Excute these in stock firmware shell:
a. nvram set boot_wait=on
b. nvram set bootdelay=3
c. nvram commit
Or in OpenWrt:
a. opkg update && opkg install kmod-mtd-rw
b. insmod mtd-rw i_want_a_brick=1
c. fw_setenv boot_wait on
d. fw_setenv bootdelay 3
e. rmmod mtd-rw
Migrate to OpenWrt:
1. Transfer squashfs-firmware.bin to the router.
2. nvram set flag_try_sys1_failed=0
3. nvram set flag_try_sys2_failed=1
4. nvram commit
5. mtd -r write /path/to/image/squashfs-firmware.bin firmware
Additional Info:
1. CR660x series routers has a different nand layout compared to other
Xiaomi nand devices.
2. This router has a relatively fresh uboot (2018.09) compared to other
Xiaomi devices, and it is capable of booting fit image firmware.
Unfortunately, no successful attempt of booting OpenWrt fit image
were made so far. The cause is still yet to be known. For now, we use
legacy image instead.
Signed-off-by: Raymond Wang <infiwang@pm.me>
Hardware
--------
SoC: QCN5502
Flash: 16 MiB
RAM: 128 MiB
Ethernet: 1 gigabit port
Wireless No1: QCN5502 on-chip 2.4GHz 4x4
Wireless No2: QCA9984 pcie 5GHz 4x4
USB: none
Installation
------------
Flash the factory image using the stock web interface or TFTP the
factory image to the bootloader.
What works
----------
- LEDs
- Ethernet port
- 5GHz wifi (QCA9984 pcie)
What doesn't work
-----------------
- 2.4GHz wifi (QCN5502 on-chip)
(I was not able to make this work, probably because ath9k requires
some changes to support QCN5502.)
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
fgrep is deprecated and replaced by grep -F. The latter is used
throughout the tree whereas this is the only usage of the former.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Now that we have separate files for each kernel version,
only the version/hash for the target kernel are available.
This cause a missing hash error (and wrong kernel version) for
bpf-headers when a testing kernel version is used for the current target.
Fix this error by manually including the kernel version/hash file for the
specific kernel version requested.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Add a package for util-linux' ipcs command, to show information about
System V inter-process communication facilities.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
ZTE MF286 is an indoor LTE category 6 CPE router with simultaneous
dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit
Ethernet switch, FXS and external USB 2.0 port.
Hardware highlights:
- CPU: QCA9563 SoC at 775MHz,
- RAM: 128MB DDR2,
- NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only,
- NAND Flash: GD5F1G04UBYIG 128MB SPI NAND-Flash, for all other data,
- Wi-Fi 5GHz: QCA9882 2x2 MIMO 802.11ac radio,
- WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio,
- Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port,
- WWAN: MDM9230-based category 6 internal LTE modem in extended
mini-PCIE form factor, with 3 internal antennas and 2 external antenna
connections, single mini-SIM slot. Modem model identified as MF270,
- FXS: one external ATA port (handled entirely by modem part) with two
physical connections in parallel,
- USB: Single external USB 2.0 port,
- Switches: power switch, WPS, Wi-Fi and reset buttons,
- LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery,
Signal state) handled entirely by modem. 4 link status LEDs handled by
the switch on the backside.
- Battery: 3Ah 1-cell Li-Ion replaceable battery, with charging and
monitoring handled by modem.
- Label MAC device: eth0
Console connection: connector X2 is the console port, with the following
pinout, starting from pin 1, which is the topmost pin when the board is
upright:
- VCC (3.3V). Do not use unless you need to source power for the
converer from it.
- TX
- RX
- GND
Default port configuration in U-boot as well as in stock firmware is
115200-8-N-1.
Installation:
Due to different flash layout from stock firmware, sysupgrade from
within stock firmware is impossible, despite it's based on QSDK which
itself is based on OpenWrt.
STEP 0: Stock firmware update:
As installing OpenWrt cuts you off from official firmware updates for
the modem part, it is recommended to update the stock firmware to latest
version before installation, to have built-in modem at the latest firmware
version.
STEP 1: gaining root shell:
Method 1:
This works if busybox has telnetd compiled in the binary.
If this does not work, try method 2.
Using well-known exploit to start telnetd on your router - works
only if Busybox on stock firmware has telnetd included:
- Open stock firmware web interface
- Navigate to "URL filtering" section by going to "Advanced settings",
then "Firewall" and finally "URL filter".
- Add an entry ending with "&&telnetd&&", for example
"http://hostname/&&telnetd&&".
- telnetd will immediately listen on port 4719.
- After connecting to telnetd use "admin/admin" as credentials.
Method 2:
This works if busybox does not have telnetd compiled in. Notably, this
is the case in DNA.fi firmware.
If this does not work, try method 3.
- Set IP of your computer to 192.168.1.22.
- Have a TFTP server running at that address
- Download MIPS build of busybox including telnetd, for example from:
https://busybox.net/downloads/binaries/1.21.1/busybox-mips
and put it in it's root directory. Rename it as "telnetd".
- As previously, login to router's web UI and navigate to "URL
filtering"
- Using "Inspect" feature, extend "maxlength" property of the input
field named "addURLFilter", so it looks like this:
<input type="text" name="addURLFilter" id="addURLFilter" maxlength="332"
class="required form-control">
- Stay on the page - do not navigate anywhere
- Enter "http://aa&zte_debug.sh 192.168.1.22 telnetd" as a filter.
- Save the settings. This will download the telnetd binary over tftp and
execute it. You should be able to log in at port 23, using
"admin/admin" as credentials.
Method 3:
If the above doesn't work, use the serial console - it exposes root shell
directly without need for login. Some stock firmwares, notably one from
finnish DNA operator lack telnetd in their builds.
STEP 2: Backing up original software:
As the stock firmware may be customized by the carrier and is not
officially available in the Internet, IT IS IMPERATIVE to back up the
stock firmware, if you ever plan to returning to stock firmware.
Method 1: after booting OpenWrt initramfs image via TFTP:
PLEASE NOTE: YOU CANNOT DO THIS IF USING INTERMEDIATE FIRMWARE FOR INSTALLATION.
- Dump stock firmware located on stock kernel and ubi partitions:
ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin
ssh root@192.168.1.1: cat /dev/mtd8 > mtd8_ubi.bin
And keep them in a safe place, should a restore be needed in future.
Method 2: using stock firmware:
- Connect an external USB drive formatted with FAT or ext4 to the USB
port.
- The drive will be auto-mounted to /var/usb_disk
- Check the flash layout of the device:
cat /proc/mtd
It should show the following:
mtd0: 00080000 00010000 "uboot"
mtd1: 00020000 00010000 "uboot-env"
mtd2: 00140000 00020000 "fota-flag"
mtd3: 00140000 00020000 "caldata"
mtd4: 00140000 00020000 "mac"
mtd5: 00600000 00020000 "cfg-param"
mtd6: 00140000 00020000 "oops"
mtd7: 00800000 00020000 "web"
mtd8: 00300000 00020000 "kernel"
mtd9: 01f00000 00020000 "rootfs"
mtd10: 01900000 00020000 "data"
mtd11: 03200000 00020000 "fota"
Differences might indicate that this is NOT a vanilla MF286 device but
one of its later derivatives.
- Copy over all MTD partitions, for example by executing the following:
for i in 0 1 2 3 4 5 6 7 8 9 10 11; do cat /dev/mtd$i > \
/var/usb_disk/mtd$i; done
- If the count of MTD partitions is different, this might indicate that
this is not a standard MF286 device, but one of its later derivatives.
- (optionally) rename the files according to MTD partition names from
/proc/mtd
- Unmount the filesystem:
umount /var/usb_disk; sync
and then remove the drive.
- Store the files in safe place if you ever plan to return to stock
firmware. This is especially important, because stock firmware for
this device is not available officially, and is usually customized by
the mobile providers.
STEP 3: Booting initramfs image:
Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
set your computer's IP address as 192.168.1.22. This is the default
expected by U-boot. You may wish to change that, and alter later
commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:
setenv serverip 192.168.1.22
setenv ipaddr 192.168.1.1
tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin
bootm 0x81000000
(Replace server IP and router IP as needed). There is no emergency
TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
installation.
Method 2: using initramfs image as temporary boot kernel
This exploits the fact, that kernel and rootfs MTD devices are
consecutive on NAND flash, so from within stock image, an initramfs can
be written to this area and booted by U-boot on next reboot, because it
uses "nboot" command which isn't limited by kernel partition size.
- Download the initramfs-kernel.bin image
- Split the image into two parts on 3MB partition size boundary, which
is the size of kernel partition. Pad the output of second file to
eraseblock size:
dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \
bs=128k count=24 \
of=openwrt-ath79-zte_mf286-intermediate-kernel.bin
dd if=openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin \
bs=128k skip=24 conv=sync \
of=openwrt-ath79-zte_mf286-intermediate-rootfs.bin
- Copy over /usr/bin/flash_eraseall and /usr/bin/nandwrite utilities to
/tmp. This is CRITICAL for installation, as erasing rootfs will cut
you off from those tools on flash!
- After backing up the previous MTD contents, write the images to the
respective MTD devices:
/tmp/flash_eraseall /dev/<kernel-mtd>
/tmp/nandwrite /dev/<kernel-mtd> \
/var/usb_disk/openwrt-ath79-zte_mf286-intermediate-kernel.bin
/tmp/flash_eraseall /dev/<kernel-mtd>
/tmp/nandwrite /dev/<rootfs-mtd> \
/var/usb_disk/openwrt-ath79-zte_mf286-intermediate-rootfs.bin
- Ensure that no bad blocks were present on the devices while writing.
If they were present, you may need to vary the split between
kernel and rootfs parts, so U-boot reads a valid uImage after skipping
the bad blocks. If it fails, you will be left with method 3 (below).
- If write is OK, reboot the device, it will reboot to OpenWrt
initramfs:
reboot -f
- After rebooting, SSH into the device and use sysupgrade to perform
proper installation.
Method 3: using built-in TFTP recovery (LAST RESORT):
- With that method, ensure you have complete backup of system's NAND
flash first. It involves deliberately erasing the kernel.
- Download "-initramfs-kernel.bin" image for the device.
- Prepare the recovery image by prepending 8MB of zeroes to the image,
and name it root_uImage:
dd if=/dev/zero of=padding.bin bs=8M count=1
cat padding.bin openwrt-ath79-nand-zte_mf286-initramfs-kernel.bin >
root_uImage
- Set up a TFTP server at 192.0.0.1/8. Router will use random address
from that range.
- Put the previously generated "root_uImage" into TFTP server root
directory.
- Deliberately erase "kernel" partition" using stock firmware after
taking backup. THIS IS POINT OF NO RETURN.
- Restart the device. U-boot will attempt flashing the recovery
initramfs image, which will let you perform actual installation using
sysupgrade. This might take a considerable time, sometimes the router
doesn't establish Ethernet link properly right after booting. Be
patient.
- After U-boot finishes flashing, the LEDs of switch ports will all
light up. At this moment, perform power-on reset, and wait for OpenWrt
initramfs to finish booting. Then proceed to actual installation.
STEP 4: Actual installation:
- scp the sysupgrade image to the device:
scp openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin \
root@192.168.1.1:/tmp/
- ssh into the device and execute sysupgrade:
sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286-squashfs-sysupgrade.bin
- Wait for router to reboot to full OpenWrt.
STEP 5: WAN connection establishment
Since the router is equipped with LTE modem as its main WAN interface, it
might be useful to connect to the Internet right away after
installation. To do so, please put the following entries in
/etc/config/network, replacing the specific configuration entries with
one needed for your ISP:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option auth '<auth>' # As required, usually 'none'
option pincode '<pin>' # If required by SIM
option apn '<apn>' # As required by ISP
option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6'
For example, the following works for most polish ISPs
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option auth 'none'
option apn 'internet'
option pdptype 'ipv4'
If you have build with LuCI, installing luci-proto-qmi helps with this
task.
Restoring the stock firmware:
Preparation:
If you took your backup using stock firmware, you will need to
reassemble the partitions into images to be restored onto the flash. The
layout might differ from ISP to ISP, this example is based on generic stock
firmware.
The only partitions you really care about are "web", "kernel", and
"rootfs". For easy padding and possibly restoring configuration, you can
concatenate most of them into images written into "ubi" meta-partition
in OpenWrt. To do so, execute something like:
cat mtd5_cfg-param.bin mtd6-oops.bin mtd7-web.bin mtd9-rootfs.bin > \
mtd8-ubi_restore.bin
You can skip the "fota" partition altogether,
it is used only for stock firmware update purposes and can be overwritten
safely anyway. The same is true for "data" partition which on my device
was found to be unused at all. Restoring mtd5_cfg-param.bin will restore
the stock firmware configuration you had before.
Method 1: Using initramfs:
- Boot to initramfs as in step 3:
- Completely detach ubi0 partition using ubidetach /dev/ubi0_0
- Look up the kernel and ubi partitions in /proc/mtd
- Copy over the stock kernel image using scp to /tmp
- Erase kernel and restore stock kernel:
(scp mtd4_kernel.bin root@192.168.1.1:/tmp/)
mtd write <kernel_mtd> mtd4_kernel.bin
rm mtd4_kernel.bin
- Copy over the stock partition backups one-by-one using scp to /tmp, and
restore them individually. Otherwise you might run out of space in
tmpfs:
(scp mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/)
mtd write <ubiconcat0_mtd> mtd3_ubiconcat0.bin
rm mtd3_ubiconcat0.bin
(scp mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/)
mtd write <ubiconcat1_mtd> mtd5_ubiconcat1.bin
rm mtd5_ubiconcat1.bin
- If the write was correct, force a device reboot with
reboot -f
Method 2: Using live OpenWrt system (NOT RECOMMENDED):
- Prepare a USB flash drive contatining MTD backup files
- Ensure you have kmod-usb-storage and filesystem driver installed for
your drive
- Mount your flash drive
mkdir /tmp/usb
mount /dev/sda1 /tmp/usb
- Remount your UBI volume at /overlay to R/O
mount -o remount,ro /overlay
- Write back the kernel and ubi partitions from USB drive
cd /tmp/usb
mtd write mtd4_kernel.bin /dev/<kernel_mtd>
mtd write mtd8_ubi.bin /dev/<kernel_ubi>
- If everything went well, force a device reboot with
reboot -f
Last image may be truncated a bit due to lack of space in RAM, but this will happen over "fota"
MTD partition which may be safely erased after reboot anyway.
Method 3: using built-in TFTP recovery (LAST RESORT):
- Assemble a recovery rootfs image from backup of stock partitions by
concatenating "web", "kernel", "rootfs" images dumped from the device,
as "root_uImage"
- Use it in place of "root_uImage" recovery initramfs image as in the
TFTP pre-installation method.
Quirks and known issues
- Kernel partition size is increased to 4MB compared to stock 3MB, to
accomodate future kernel updates - at this moment OpenWrt 5.10 kernel
image is at 2.5MB which is dangerously close to the limit. This has no
effect on booting the system - but keep that in mind when reassembling
an image to restore stock firmware.
- uqmi seems to be unable to change APN manually, so please use the one
you used before in stock firmware first. If you need to change it,
please use protocok '3g' to establish connection once, or use the
following command to change APN (and optionally IP type) manually:
echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0
- The only usable LED as a "system LED" is the green debug LED hidden
inside the case. All other LEDs are controlled by modem, on which the
router part has some influence only on Wi-Fi LED.
- Wi-Fi LED currently doesn't work while under OpenWrt, despite having
correct GPIO mapping. All other LEDs are controlled by modem,
including this one in stock firmware. GPIO19, mapped there only acts
as a gate, while the actual signal source seems to be 5GHz Wi-Fi
radio, however it seems it is not the LED exposed by ath10k as
ath10k-phy0.
- GPIO5 used for modem reset is a suicide switch, causing a hardware
reset of whole board, not only the modem. It is attached to
gpio-restart driver, to restart the modem on reboot as well, to ensure
QMI connectivity after reboot, which tends to fail otherwise.
- Modem, as in MF283+, exposes root shell over ADB - while not needed
for OpenWrt operation at all - have fun lurking around.
- MAC address shift for 5GHz Wi-Fi used in stock firmware is
0x320000000000, which is impossible to encode in the device tree, so I
took the liberty of using MAC address increment of 1 for it, to ensure
different BSSID for both Wi-Fi interfaces.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
ZTE MF286D is a LTE router with four gigabit ethernet ports
and integrated QMI mPCIE modem.
Hardware specification:
- CPU: IPQ4019
- RAM: 256MB
- Flash: NAND 128MB + NOR 2MB
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11anac 2x2:2
- LTE: mPCIe cat 12 card (Modem chipset MDM9250)
- LAN: 4 Gigabit Ports
- USB: 1x USB2.0 (regular port). 1x USB3.0 (mpcie - used by the modem)
- Serial console: X8 connector 115200 8n1
Known issues:
- Many LEDs are driven by the modem. Only internal LEDs and wifi LEDs
are driven by cpu.
- Wifi LED is triggered by phy0tpt only
- No VoIP support
- LAN1/WAN port is configured as WAN
- ZTE gives only one MAC per device. Use +1/+2/+3 increment for WAN
and WLAN0/1
Opening the case:
1. Take of battery lid (no battery support for this model, battery cage
is dummy).
2. Unscrew screw placed behind battery lid.
3. Take off back cover. It attached with multiple plastic clamps.
4. Unscrew four more screws hidden behind back case.
5. Remove front panel from blue chassis. There are more plastic
clamps.
6. Unscrew two boards, which secures the PCB in the chassis.
7. Extract board from blue chassis.
Console connection (X8 connector):
1. Parameters: 115200 8N1
2. Pin description: (from closest pin to X8 descriptor to farthest)
- VCC (3.3V)
- TX
- RX
- GND
Install Instructions:
Serial + initramfs:
1. Place OpenWrt initramfs image for the device on a TFTP in
the server's root. This example uses Server IP: 192.168.1.3
2. Connect serial console (115200,8n1) to X8 connector.
3. Connect TFTP server to RJ-45 port.
4. Stop in u-Boot and run u-Boot commands:
setenv serverip 192.168.1.3
setenv ipaddr 192.168.1.72
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf286d-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert
to stock.
6. Login via ssh or serial and remove stock partitions:
ubiattach -m 9
ubirmvol /dev/ubi0 -N ubi_rootfs
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. Install image via "sysupgrade -n".
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cosmetic changes to the commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Kalle Valo ath10k-firmware repository no longer provides the
legacy board.bin files for the qca99x0 chips. Instead he
copied over the codeaurora version and add more board files.
In the future, this board-2.bin should find its way to
linux-firmware.git, which would allow us to remove the
extra download code completely.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
this should have been removed together with linux 5.4 APM821XX
support. Currently, this didn't hurt or broke something. But it
will in the next stable kernel release.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The SDK does not ship the generic platform files. Use relative path for
GENERIC_PLATFORM_DIR to make it work. This points it at the files from
the feed directory instead of the base SDK path
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All devices which used this package migrated to the kernel GPIO-line
watchdog driver and configure it over their DT.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This solves issue with DDR training on Turris Omnia.
Log:
******** DRAM initialization Failed (res 0x1) ********
DDR3 Training Sequence - FAILED
ERROR ### Please RESET the board ###
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Now that we can have both legacy and nft iptables variants
installed at the same time, install the legacy symlinks
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
As nftables is now the default, ip(6)tables-nft gets higher priority
The removed symlinks ("$(CP)" line) will now be installed by the
ALTERNATIVES mechanism
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
according to iptables-nft man page,
"These tools use the libxtables framework extensions and hook to the nf_tables
kernel subsystem using the nft_compat module."
This means that to work, iptables-nft needs the same modules as
iptables legacy except the ip(6)table-{filter,mangle,nat,raw}
ip_tables, ip6tables.
When those modules are loaded iptables-nft-save output contains
"# Warning: iptables-legacy tables present, use iptables-legacy-save to see them"
But as long as it's empty it should not be a problem.
To have nft properly display the rules created by ip(6)tables-nft we need
all iptables targets and matches to be built as extension and not built-in
(/usr/lib/iptables/libip(6)t_*.so)
When switching a package to iptables-nft, you need to keep the
iptables-mod-* dependencies
This patch does minimal changes:
- remove the direct iptables-nft -> iptables dependency
- and more important add nft-compat dependency
The rule
iptables-nft -A OUTPUT -d 8.8.8.8 -m comment --comment "aaa" -j REJECT
becomes
table ip filter {
chain OUTPUT {
type filter hook output priority filter; policy accept;
ip daddr 8.8.8.8 # xt_comment counter packets 0 bytes 0 # xt_REJECT
}
}
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Add option to compile kmod-vrf, support for Virtual Routing and
Forwarding (Lite).
This module depends on NET_L3_MASTER_DEV, which is a boolean kernel
option, so we need to create a configuration option also for this, and
make kmod-vrf depend on it.
Signed-off-by: Marek Behún <kabel@kernel.org>
The sizes of the ipk changed on MIPS 24Kc like this:
13281 uboot-envtools_2021.01-54_mips_24kc.ipk
13308 uboot-envtools_2022.01-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sizes of the ipk changed on MIPS 24Kc like this:
11248 libcap_2.51-1_mips_24kc.ipk
14461 libcap_2.63-1_mips_24kc.ipk
18864 libcap-bin_2.51-1_mips_24kc.ipk
20576 libcap-bin_2.63-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This release fixes two security mount(8) and umount(8) issues:
CVE-2021-3996
Improper UID check in libmount allows an unprivileged user to unmount FUSE
filesystems of users with similar UID.
CVE-2021-3995
This issue is related to parsing the /proc/self/mountinfo file allows an
unprivileged user to unmount other user's filesystems that are either
world-writable themselves or mounted in a world-writable directory.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The man page of the raw tool does not build because the disk-utils/raw.8
file is missing. It looks like it should be in the tar.xz file we
download, but it is missing.
We do not package the raw tool, so this is not a problem.
This fixes the following build error:
No rule to make target 'disk-utils/raw.8', needed by 'all-am'. Stop.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sizes of the ipk changed on MIPS 24Kc like this:
289764 strace_5.14-1_mips_24kc.ipk
310899 strace_5.16-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
795f420 cmis: Rename CMIS parsing functions
369b43a cmis: Initialize CMIS memory map
da16288 cmis: Use memory map during parsing
6acaeb9 cmis: Consolidate code between IOCTL and netlink paths
d7d15f7 sff-8636: Rename SFF-8636 parsing functions
4230597 sff-8636: Initialize SFF-8636 memory map
b74c040 sff-8636: Use memory map during parsing
799572f sff-8636: Consolidate code between IOCTL and netlink paths
9fdf45c sff-8079: Split SFF-8079 parsing function
2ccda25 netlink: eeprom: Export a function to request an EEPROM page
86792db cmis: Request specific pages for parsing in netlink path
6e2b32a sff-8636: Request specific pages for parsing in netlink path
c2170d4 sff-8079: Request specific pages for parsing in netlink path
9538f38 netlink: eeprom: Defer page requests to individual parsers
664586e Merge branch 'review/next/module-mem-map' into master
50fdaec ethtool: Set mask correctly for dumping advertised FEC modes
c5e7133 cable-test: Fix premature process termination
73091cd sff-8636: Use an SFF-8636 specific define for maximum number of channels
837c166 sff-common: Move OFFSET_TO_U16_PTR() to common header file
8658852 cmis: Initialize Page 02h in memory map
27b42a9 cmis: Initialize Banked Page 11h in memory map
340d88e cmis: Parse and print diagnostic information
eae6a99 cmis: Print Module State and Fault Cause
82012f2 cmis: Print Module-Level Controls
d7b1007 sff-8636: Print Power set and Power override bits
429f2fc Merge branch 'review/cmis-diag' into master
32457a9 monitor: do not show duplicate options in help text
c01963e Release version 5.16.
The sizes of the ipk changed on MIPS 24Kc like this:
34317 ethtool_5.15-1_mips_24kc.ipk
34311 ethtool_5.16-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the following security problems:
* Zeroize several intermediate variables used to calculate the expected
value when verifying a MAC or AEAD tag. This hardens the library in
case the value leaks through a memory disclosure vulnerability. For
example, a memory disclosure vulnerability could have allowed a
man-in-the-middle to inject fake ciphertext into a DTLS connection.
* Fix a double-free that happened after mbedtls_ssl_set_session() or
mbedtls_ssl_get_session() failed with MBEDTLS_ERR_SSL_ALLOC_FAILED
(out of memory). After that, calling mbedtls_ssl_session_free()
and mbedtls_ssl_free() would cause an internal session buffer to
be free()'d twice. CVE-2021-44732
The sizes of the ipk changed on MIPS 24Kc like this:
182454 libmbedtls12_2.16.11-2_mips_24kc.ipk
182742 libmbedtls12_2.16.12-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a minor corrective release over GDB 11.1, fixing the following issues:
* PR sim/28302 (gdb fails to build with glibc 2.34)
* PR build/28318 (std::thread support configure check does not use CXX_DIALECT)
* PR gdb/28405 (arm-none-eabi: internal-error: ptid_t remote_target::select_thread_for_ambiguous_stop_reply(const target_waitstatus*): Assertion `first_resumed_thread != nullptr' failed)
* PR tui/28483 ([gdb/tui] breakpoint creation not displayed)
* PR build/28555 (uclibc compile failure since commit 4655f8509fd44e6efabefa373650d9982ff37fd6)
* PR rust/28637 (Rust characters will be encoded using DW_ATE_UTF)
* PR gdb/28758 (GDB 11 doesn't work correctly on binaries with a SHT_RELR (.relr.dyn) section)
* PR gdb/28785 (Support SHT_RELR (.relr.dyn) section)
The sizes of the ipk changed on mips 24Kc like this:
2285775 gdb_11.1-3_mips_24kc.ipk
2287441 gdb_11.2-4_mips_24kc.ipk
191828 gdbserver_11.1-3_mips_24kc.ipk
191811 gdbserver_11.2-4_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the most recent supported firmware file for Intel Wi-Fi 6E AX210
wireless chip. The API version 67 is not yet supported by the driver.
Additional PNVM file is required since API version 62.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Just use 'start' action which will have the desired effect instead of
trying to introduce a 'start_file' action which didn't work that way
because procd jshn magic would have to wrap around it.
Fixes: 88baf6ce2c ("ubox: only start log to file when filesystem has been mounted")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
From: Peter Lundkvist <peter.lundkvist@gmail.com>
This fixes the make_syscall_h.sh script to recognize both
__NR_Linux, used by mips, and __NR_SYSCALL_BASE and
__ARM_NR_BASE used by arm.
Run-tested on arm (ipq806x) and mips (ath79), both with glibc.
Compile-tested and checked resulting syscall_names.h file wuth
glibc: aarch64, powerpc, x86_64, i486
musl: arm, mips
Fixes: FS#4194, FS#4195
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If log_file is on an filesystem mounted using /etc/config/fstab we have
to wait for that to happen before starting the logread process.
Inhibit the start of the file-writer process and use a mount trigger to
fire it up once the filesystem actually becomes available.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow init scripts to trigger free-form actions by exposing
procd_add_action_mount_trigger.
Clean up mount trigger wrappers while at it to reduce code duplication.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The arc700 target is not booting up since some time, see here:
https://github.com/foss-for-synopsys-dwc-arc-processors/toolchain/issues/400
It looks like there is a problem in the toolchain when using glibc.
Currently no one is working on fixing this problem, remove the target
instead. This target also does not have many users we are aware of.
If someone wants to have this target back, feel free to add a fixed
version of this target again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
bpftool will enabled libbfd and libopcodes which gets picked up by perf
as libraries to link against. Add those missing dependencies when either
of these packages are enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
nf-nathelper-extra and nf-conntrack-netlink had iptables related
dependencies, yet, when looking for the respective kernel symbols and
checking it's dependencies it was confirmed that iptables wasn't
required and that these were either it's own moodule or tool independent
(nftables or iptables).
Correct these and make sure no unneeded extras are pulled in.
Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
Add U-Boot env settings to allow accessing the environment using
fw_printenv and fw_setenv tools on the UniElec U7623 board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Brings bootmenu and production/recovery dual-boot scheme like on
the BPi-R2, BPi-R64, E8450 and UniFi 6 LR.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The ucode VM always passes 64bit integer values to sprintf implementation
while the `%d` format expects 32bit integers on 32bit platforms, leading
to incorrect formatting results.
Temporarily solve the issue by casting the numeric argument to int until
a more thorough fix arrives with the next update.
Fixes: FS#4234
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This removes -static compile option. The -static option tells GCC to
link this statically with the libc, which we do not want in OpenWrt. We
want to link everything dynamically to the libc. This fixes a compile
problem with glibc.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the nohostroute option as available for gre and wg tunnels to
allow the user to prevent explicit creation of a route to the peer
address.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Device specifications:
======================
* Qualcomm/Atheros AR7240 rev 2
* 350/350/175 MHz (CPU/DDR/AHB)
* 32 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ 18-24V passive POE (mode B)
+ used as WAN interface
- eth1
+ builtin switch port 4
+ used as LAN interface
* 12-24V 1A DC
* external antenna
The device itself requires the mtdparts from the uboot arguments to
properly boot the flashed image and to support dual-boot (primary +
recovery image). Unfortunately, the name of the mtd device in mtdparts is
still using the legacy name "ar7240-nor0" which must be supplied using the
Linux-specfic DT parameter linux,mtd-name to overwrite the generic name
"spi0.0".
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Changes from 2.1.3 to 2.1.4:
Features:
- ubiscan debugging and statistics utility
Fixes:
- Some mtd-tests erroneously using sub-pages instead of the full page size
- Buffer overrun in fectest
- Missing jffs2 kernel header in the last release, leading to build
failures on some systems.
Changes from 2.1.2 to 2.1.3:
Features:
flashcp: Add new function that copy only different blocks
flash_erase: Add flash erase chip
Add flash_otp_erase
Add an ubifs mount helper
Add nandflipbits tool
Fixes:
mkfs.ubifs: Fix runtime assertions when running without crypto
mtd-utils: Use AC_SYS_LARGEFILE
Fix test binary installation
libmtd: avoid divide by zero
ubihealthd: fix UBIFS build dependency
mkfs.ubifs: remove OPENSSL_no_config()
misc-utils: Add fectest to build system
mkfs.ubifs: Fix build with SELinux
Fix typos found by Debian's lintian tool
Fix jffs2 build if zlib or lzo headers are not in default paths
Signed-off-by: Nick Hainke <vincent@systemli.org>
x86, mt7623 and others buildbot failed due to:
|Package kmod-hwmon-nct7802 is missing dependencies for the following libraries:
|regmap-core.ko
|regmap-i2c.ko
Fixes: 1ed50b92d1 ("package: kernel: add driver module for NCT7802Y")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit add package with hwmon-nct7802 module.
This driver implements support for the Nuvoton NCT7802Y hardware monitoring
chip. NCT7802Y supports 6 temperature sensors, 5 voltage sensors, and 3 fan
speed sensors.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(fixed c&p'ed module description)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SOC: IPQ4019
CPU: Quad-core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
DRAM: 256 MB
NAND: 128 MiB Macronix MX30LF1G18AC
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4x LAN, 1x WAN)
USB: 1x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
WLAN2: Qualcomm Atheros QCA9984 5GHz 802.11nac 4x4:4
INPUT: 1x WPS, 1x Reset
LEDS: Status, WIFI1, WIFI2, WAN (red & blue), 4x LAN
This board is very similar to the RT-ACRH13/RT-AC58U. It must be flashed
with an intermediary initramfs image, the jffs2 ubi volume deleted, and
then finally a sysupgrade with the final image performed.
Signed-off-by: Joshua Roys <roysjosh@gmail.com>
(added ALT0)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
OpenWrt plans to move over to firewall4 which uses nftables under the
hood. To allow a smooth migration the package `iptables-nft` offer a
transparent wrapper to apply iptables rules to nftables.
Without the config option for nftables the package isn't installed and
therefore can't be tested. This commit enabled it and therefore provides
the wrapper.
The size of the iptables package increases from 25436 to 26500 Bytes.
Signed-off-by: Paul Spooren <mail@aparcar.org>
ca6c35c uxc: usage message cosmetics
e083dd4 uxc: fix two minor issues reported by Coverity
35dfbff procd: jail/cgroups: correctly enable "rdma" when requested
3b3ac64 procd: mount /dev with noexec
ac2b8b3 procd: clean up /dev/pts mounts
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
0f16ea5 options.c: add DSCP code LE Least Effort
24ba465 firewall3: remove redundant syn check
df1306a firewall3: fix locking issue
3624c37 firewall3: support table load on access on Linux 5.15+
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 1T1R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ 10/100 Mbps Ethernet
+ builtin switch port 1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
db7fb64 libopkg: pkg_hash: prefer to-be-installed packages
2edcfad libopkg: set 'const' attribute for argv
This should fix the ImageBuilder problems people are having since we
introduced the 'uci-firewall' providers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
9a509d4 ruleset.uc: consolidate ip and ip6 offload
21f311d ruleset.uc: don't trim newline before comment sign
f121383 tests: enable flow offloading in tests
550df40 tests: add test for unknown defaults option
47c5a5b tests: add test for deprecated rule option
69a89d6 tests: add test for unknown rule option
07579df fw4.uc: handle interface zone option
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Almost all targets have the fixed-phy feature built into the kernel.
One big exception is x86. This caused a problem with the upcoming
LAN78xx usb driver. Hence this patch breaks out the fixed-phy from
of_mdio (which didn't include the .ko) and puts into a separate
module.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
phy drivers for Microchip's LAN88xx PHYs.
This is needed for the "LAN7801" variant
of the upstream lan78xx usb ethernet driver.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
libdw depends on libfts.so when building with the musl-libc library, add
this missing dependency.
Fixes: 6835ea13f0 ("elfutils: update to 0.186")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Linux upstream commit 9370f2d05a
add load firmware file through request_firmware,this affect the
nanopi r2s and some USB adapters in kernel 5.10 with this error:
'r8152 4-1:1.0: unable to load firmware patch rtl_nic/rtl8153b-2.fw'
This patch split the USB NIC firmware files from r8169 firmware,
and adds r8152-firmware to r8152 driver.
Add kmod-usb-net-cdc-ncm to support RTL8156A and RTL8156B 2.5G ethernet
adapters supported since v5.13-rc1.
195aae321c
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Update busybox to 1.35.0
* refresh patches
Config refresh:
Refresh commands, run after busybox is first built once:
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.35.0
cd ..
./convert_defaults.pl ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.35.0/.config > Config-defaults.in
Manual edits needed after config refresh:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt configTARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in : change at "Options common to all shells" the symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
session tickets are a feature of TLSv1.2 and require less memory
and overhead on the server than does managing a session cache
Building mbedtls with support for session tickets will allow the
feature to be used with lighttpd-1.4.56 and later.
Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
Specifications:
- SoC: MT7621DAT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 128 MB NAND
- Ethernet: 5x 1GiE MT7530
- WiFi: MT7603/MT7613
- USB: 1x USB 3.0
This is another MT7621 device, very similar to other Linksys EA7300
series devices.
Installation:
Upload the generated factory.bin image via the stock web firmware
updater.
Reverting to factory firmware:
Like other EA7300 devices, this device has an A/B router configuration
to prevent bricking. Hard-resetting this device three (3) times will
put the device in failsafe (default) mode. At this point, flash the
OEM image to itself and reboot. This puts the router back into the 'B'
image and allows for a firmware upgrade.
Troubleshooting:
If the firmware will not boot, first restore the factory as described
above. This will then allow the factory.bin update to be applied
properly.
Signed-off-by: Nick McKinney <nick@ndmckinney.net>
CHECK_RUN_DIR=0 must be a part of MAKE_FLAGS, not MAKE_VARS, otherwise
it is not possible to compile mdadm on host without /run dir.
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
glibc version 2.34 does not provide versioned shared libraries any more,
it only provides shared libraries using the ABI version. Do not try to
copy them any more.
The functions from libpthread and librt were integrated into the main
binary, the libpthread.so and librt.so are only used for backwards
compatibility any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Provide uci-firewall via PROVIDES in both firewall and firewall4. This
will allow us to change the dependency of luci-app-firewall to
uci-firewall, making it possible to use it with either implementation.
Move CONFLICTS from firewall4 to firewall, to solve this recursive
dependency problem:
tmp/.config-package.in:307:error: recursive dependency detected!
tmp/.config-package.in:307: symbol PACKAGE_firewall is selected by PACKAGE_firewall4
tmp/.config-package.in:328: symbol PACKAGE_firewall4 depends on PACKAGE_firewall
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
4ead2a6 treewide: move executables to /sbin
9ebc2f4 fw4.uc: filter duplicates in fw4.set
85b74f3 treewide: support flow offloading
be3b4e6 treewide: support hardware flow offloading
38889b7 treewide: support set timeout
31c7550 fw4.uc: do not skip defaults with invalid option
334a127 fw4.uc: introduce DEPRECATED flag
7a0d38f fw4.uc: add _name as deprecated option
5e7ad3b fw4.uc: don't fail on unknown options
be5f4e3 fw4.uc: allow use of cidr in ipsets
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
The limitation of not being able to use iptables and nft nat at the same
time exists only in kernels before 4.18.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
ARC4 was used for WEP, which is not secure anymore. Therefor it is
disabled in the driver, but the code is not removed for now.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The lantiq AES hardware does not support the gcm algorithm. But it
can be implemented in the driver as a combination of the aes_ctr
algorithm and the xor plus gfmul operations for the hashing.
Due to the wrapping of the several algorithms and the inefficient
16 byte block by 16 byte block invokation in the kernel
implementations, this driver is about 3 times faster for the larger
block sizes.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
After adding xts and cbcmac the aes algorithm source had three sections
for setting the aes key to the hardware which are identical.
Method aes_set_key_hw was created which is now called from within the
spinlock secured control sections in methods ifx_deu_aes, ifx_deu_aes_xts
and aes_cbcmac_final_impl and reduces the size of ifxmips_aes.c.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Since commit 53b6783 hostapd is using the kernel api which includes the
cbcmac-aes shash algorithm. The kernels implementation is a wrapper around
the aes encryption algorithm, which encrypts block (16 bytes) by block.
When the ltq-deu driver is present, it uses hardware aes, but every 16 byte
encrypt requires setting the key. This is very inefficient and is a huge
overhead. Since the cbcmac-aes is simply a hash that uses the cbc aes
algorithm starting with an iv set to x'00' with an optional ecb aes
encryption of a possible last incomplete block that is padded with the
positional bytes of the last cbc encrypted block, this algorithm is now
added to the driver. Most of the code is derived from md5-hmac and
tailored for aes. Tested with the kernels crypto testmgr including extra
tests against the kernels generic ccm module implementation.
This patch also fixes the overallocation in the aes_ctx that is caused
by using u32 instead of u8 for the aes keys.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Remove the dependency on kernel 5.4 from the Makefile to allow the
driver to compile with kernel 5.10 or kernel versions higher than
5.4.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The lantiq AES hardware does not support the xts algorithm. Apart
from the cipher text stealing (XTS), the AES XTS implementation is
just an XOR with the IV, followed by AES ECB, followed by another
XOR with the IV and as such can be also implemented by using the
lantiq hardware's CBC AES implemention plus one additional XOR with
the IV in the driver. The output IV by CBC AES is also not usable
and the gfmul operation not supported by lantiq hardware. Both need
to be done in the driver too in addition to the IV treatment which is
the initial encryption by the other half of the input key and to
set the IV to the IV registers for every block.
In the generic kernel implementation, the block size for XTS is set
to 16 bytes, although the algorithm is designed to process any size
of input larger than 16 bytes. But since there is no way to
indicate a minimum input length, the block size is used. This leads
to certain issues when the skcipher walk functions are used, e.g.
processing less than block size bytes is not supported by calling
skcipher_walk_done.
The walksize is 2 AES blocks because otherwise for splitted input
or output data, less than blocksize is to be returned in some cases,
which cannot be processed. Another issue was that depending on
possible split of input/output data, just 16 bytes are returned while
less than 16 bytes were remaining, while cipher text stealing
requires 17 bytes or more for processing.
For example, if the input is 60 bytes and the walk is 48, then
processing 48 bytes leads to a return code of -EINVAL for
skcipher_walk_done. Therefor the processed counter is used to
figure out, when the actual cipher text stealing for the remaining
bytes less than blocksize needs to be applied.
Measured with cryptsetup benchmark, this XTS AES implementation is
about 19% faster than the kernels XTS implementation that uses the
hardware ECB AES (ca. 18.6 MiB/s vs. 15.8 MiB/s decryption 256b key).
The implementation was tested with the kernels crypto testmgr against
the kernels generic XTS AES implementation including extended tests.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The processing in the hmac algorithms depends on the status fields:
count, dbn and started. Not all were initialised in the init method
and after finishing the final method. Added missing fields to init
method and call init method after finishing final.
The memsets have the wrong size in the original driver and did not
clear everything and are not necessary. Since no memset is done in
the kernels generic implementation, memsets were removed.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Removing hash pointer in _hmac_setkey since its not needed and causes
a compiler warning.
Make the spinlock control sections shorter and move initializations
out of the control sections to free the spinlock faster for allowing
other threads to use the hash engine.
Minor improvements for indentation and removal of blanks and blank
lines in some areas.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Exceeding the temp array size was not checked and instead storage not
allocated by the driver was used/overwritten which in most cases
resulted in reboots. This patch implements processing the input to the
hash algorithm in tempsize chunks.
The _hmac_final methods were changed to _hmac_final_impl adding a
parameter that indicates intermediate or final processing. The started
variable was added to the context to indicate, if there is an
intermediate result in the context. For sha1_hmac the variable to store
the intermediate hash was added to the context too.
In order to avoid md5_hmac_final_impl being recursively called if the
padding of the input and the resulting last transform during the hmac
algorighms final processing causes the temp array to overflow and to
make sure that there is at least one block in the temp array when the
_hmac_final for final processing is called, the check for exceeding
the temp array in _hmac_transform was moved before copying the block
and incrementing dbn. dbn needs to be at least 1 at final processing
time to let the hash engine apply the opad operation.
To make the hash engine not apply the hmac algorithms final opad
operation, for intermediate processing the dbn in the control register
is set to a higher value than number of dbns are actually processed.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The hmac algorithms state, that keys larger than the key size should be
hashed with the underlying hash algorithms and then those hashes are to
be used as keys. This patch implements this. In order to avoid allocating
a descriptor during setkey, a shash_desc pointer is added to the context.
Another issue for multithreaded callers is the shared temp array.
The temp array is static and as such would be shared among multithreaded
callers, which obviously would neither work nor produce correct results.
The temp array (4k size) is moved to the context and since the size of
the context is limited, it can only be defined as pointer otherwise the
initialisation of the hash algorithm fails.
The allocations and freeing of both the temp and the desc pointer in the
context are done by implementing cra_init and cra_exit functions for
the hmac algorithms.
Also improved indentation in some areas.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Error ifxdeu-ctr-rfc3686(aes) (16) doesn't match generic impl (20) occurs
when running the cryptomgr extra tests that compare against the linux
kernels generic implementation.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The algorithms sha1, sha1_hmac and md5_hmac all use ENDI=1. The md5
algorithm uses ENDI=0 and the endian_swap methods to reverse the
endianess switch by using user CPU time, which is unnecessary overhead.
Danube and AR9 devices do not set endianess for SHA1, so is done for
MD5.
Furthermore the patch replaces endian_swap with le32_to_cpu for md5 and
md5 hmac algorithms and removes endian_swap for them.
The init functions initialize the algorithm in the hardware. The lock is
not used to write to the control register. If another thread calls
another hash algo before update or final, the result will be wrong.
Therefore move the algorithm init to the lock protected sections in the
transform or final methods.
Setting the hw key for the hmac algorithms is now done from within the
lock protected sections in their final methods. The lock protecting is
removed from the _hmac_setkey_hw functions.
In final for md5 and sha1 the lock section is removed, because all the
work was already done in transform (which is called from final). As such
only copying the hash to the output is required.
MD5 and MD5_HMAC produce 16 byte hashes (4 DWORDS) only, therefor
writing register D5R to the hash output is removed for MD5_HMAC.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
All hash algorithms use the same base IFX_HASH_CON to access the hash unit.
Parallel threads should not be able to call different hash algorithms and
therefor a global lock is required.
Fixed linker warning, that md5_hmac_init, md5_hmac_update and
md5_hmac_final are static export symbols. The export symbols are not
required, because the functions are exposed using shash_alg structure.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The functions ifx_deu_aes_cfg and ifx_deu_aes_ofb have been part of the
driver ever since. But the functions and definitions to make the
algorithms actually usable were missing.
This patch adds the neccessary code for aes_ofb and aes_cfb algorithms.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
When running cryptomgr tests against the driver, there are several
occurences of different errors for even and uneven splitted data in the
underlying scatterlists for the ctr and ctr_rfc3686 algorithms which are
now fixed.
Fixed error in ctr_rfc3686_aes_decrypt function which was introduced with
the previous commit by using CRYPTO_DIR_ENCRYPT in the decrypt function.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
When running cryptomgr tests against the driver, there are several
occurences of different errors for setkey of des and des3-ede
algorithms.
Those key checks are already implemented in the kernels des
implementation, so this is added as dependency and the kernel methods
are called. It also required adding the kernels des/des3 context
definitions to the des_ctx internal structure to be able to call the
kernel methods.
Fixed ifxdeu-des... setkey unexpectedly succeeded on test vector x;
expected_error=-22.
Fixed ifxdeu-des... setkey failed on test vector x; expected_error=0,
actual_error=-22.
Renamed des_ctx internal structure and des_encrypt/des_decrypt methods
because they are already defined in the kernel module.
Fixed wrong DES_xxx constant definitions in crypto_alg definition for
ifxdeu_des3_ede_alg.
Fixed method comment errors.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The <linux/cryptohash.h> was removed with Linux 5.8, because it only
contained the library implementation of SHA1, which was folded
into <crypto/sha.h>.
So switch this driver away from using <linux/cryptohash.h>.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Convert blkcipher to skcipher for the synchronous versions of AES,
DES and ARC4.
The Block Cipher API was depracated for a while and was removed with
Linux 5.5. So switch this driver to the skcipher API.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Some devices initialize AES during boot and AES works out of the box
and the correct endianess is set.
NDC means (No Danube Compatibility Mode) and the endianess setting has
no effect if its set to 0.
NDC 0: OFF ENDI bit cannot be written as in Danube
To make it work for other devices, the NDC control register needs to
be set to 1.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
OpenSSL with cryptdev support uses the data encryption unit (DEU) driver
for hard accelerated processing of ciphers/digests, if the flag
CRYPTO_ALG_KERN_DRIVER_ONLY is set.
Signed-off-by: Mathias Kresin <dev@kresin.me>
[fix commit title prefix]
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Even if the minimum blocksize is set to 16 (AES_BLOCK_SIZE), the crypto
manager tests pass 499 bytes of data to the aes-ctr encryption, from
which only 496 bytes are actually encrypted.
Reading the comment regarding the minimum blocksize, it only states that
it's the "smallest possible unit which can be transformed with this
algorithm". Which doesn't necessarily mean, the data have to be a
multiple of the minimal blocksize.
All kernel hardware crypto driver enforce a minimum blocksize of 1,
which perfect fine works for the lantiq data encryption unit as well.
Lower the blocksize limit to 1, to process not padded data as well.
In AES for processing the remaining bytes, uninitialized pointers
were used.
This patch fixes using uninitialized pointers and wrong offsets.
Signed-off-by: Mathias Kresin <dev@kresin.me>
[fix commit title prefix]
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
When handling non-aligned remaining data (not padded to 16 byte
[AES_BLOCK_SIZE]), a full 16 byte block is read from the input buffer
and written to the output buffer after en-/decryption.
While code already assumes that an input buffer could have less than 16
byte remaining, as it can be seen by the code zeroing the remaining
bytes till AES_BLOCK_SIZE, the full AES_BLOCK_SIZE is read.
An output buffer size of a multiple of AES_BLOCK_SIZE is expected but
never validated.
To get rid of the read/write behind buffer, use a temporary buffer when
dealing with not padded data and only write as much bytes to the output
as we read.
Do not memcpy directly to the register, to make used of the endian swap
macro and to trigger the crypto start operator via the ID0R to trigger
the register. Since we might need an endian swap for the output in
future, use a temporary buffer for the output as well.
The issue could not be observed so far, since all caller of ifx_deu_aes
will ignore the padded (remaining) data. Considering that the minimum
blocksize for the algorithm is set to AES_BLOCK_SIZE, the behaviour
could be called expected.
Signed-off-by: Mathias Kresin <dev@kresin.me>
[fix commit title prefix]
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The crypto algorithms are registered and available to the system before
the chip is actually powered on and the generic parameter for the DEU
behaviour set.
The issue can mainly be observed if the crypto manager tests are enabled
in the kernel config. The crypto manager test run directly after an
algorithm is registered.
Signed-off-by: Mathias Kresin <dev@kresin.me>
[fix commit title prefix]
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Compiling without fPIC causes linking issues for packages using liblua.
Add $(HOST_FPIC) to host builds for both lua and lua5.3.
Suggested-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Arch Linux users have encountered problems with packages that have a dependency on binutils. This error happens when libtool is doing:
libtool: relink: ...
So change PKG_FIXUP to "patch-libtool".
Fixes error in the form of:
libtool: install: error: relink `libctf.la' with the above command
before installing it
Upstream Bug:
https://sourceware.org/bugzilla/show_bug.cgi?id=28545
OpenWrt Bug:
https://bugs.openwrt.org/index.php?do=details&task_id=4149
Acked-by: John Audia <graysky@archlinux.us>
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is a bugfix release. Changelog:
*) Avoid loading of a dynamic engine twice.
*) Fixed building on Debian with kfreebsd kernels
*) Prioritise DANE TLSA issuer certs over peer certs
*) Fixed random API for MacOS prior to 10.12
Patches were refreshed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Recently the hostapd has undergone many changes. The patches were not refreshed.
Refreshed with
make package/hostapd/{clean,refresh}
Refreshed:
- 380-disable_ctrl_iface_mib.patch
- 600-ubus_support.patch
- 700-wifi-reload.patch
- 720-iface_max_num_sta.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is required to be able to use flow offloading on devices with
ifnames that start with a digit, like 6in4-wan6.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Chromium based web-browsers (version >58) checks x509v3 extended attributes.
If this check fails then chromium does not allow to click "Proceed to ...
(unsafe)" link. This patch add three x509v3 extended attributes to self-signed
certificate:
1. SAN (Subject Alternative Name) (DNS Name) = CN (common name)
2. Key Usage = Digital Signature, Non Repudiation, Key Encipherment
3. Extended Key Usage = TLS Web Server Authentication
SAN will be added only if CONFIG_WOLFSSL_ALT_NAMES=y
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
x509v3 SAN extension is required to generate a certificate compatible with
chromium-based web browsers (version >58)
It can be disabled via unsetting CONFIG_WOLFSSL_ALT_NAMES
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
NETGEAR ReadyNAS Duo v2 is a NAS based on Marvell kirkwood SoC.
Specification:
- Processor Marvell 88F6282 (1.6 GHz)
- 256MB RAM
- 128MB NAND
- 1x GBE LAN port (PHY: Marvell 88E1318)
- 1x USB 2.0
- 2x USB 3.0
- 2x SATA
- 3x button
- 5x leds
- serial on J5 connector accessible from rear panel
(115200 8N1) (VCC,TX,RX,GND) (3V3 LOGIC!)
Installation by USB + serial:
- Copy initramfs image to fat32 usb drive
- Connect pendrive to USB 2.0 front socket
- Connect serial console
- Stop booting in u-boot
- Do:
usb reset
setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
saveenv
fatload usb 0:1 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
bootm 0x1200000
- copy sysupgrade image via ssh.
- run sysupgrade
Installation by TFTP + serial:
- Setup TFTP server and copy initramfs image
- Connect serial console
- Stop booting in u-boot
- Do:
setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
saveenv
setenv serverip 192.168.1.1
setenv ipaddr 192.168.1.2
tftpboot 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
bootm 0x1200000
- copy sysupgrade image via ssh.
- run sysupgrade
Known issues:
- Power button and PHY INTn pin are connected to the same GPIO. It
causes that every network restart button is pressed in system.
As workaround, button is used as regular BTN_1.
For more info please look at file:
RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c
from Netgear GPL sources.
Tested-by: Raylynn Knight <rayknight@me.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This patch adds kernel module for Global Mixed-mode Technology Inc
G762 and G763 fan speed PWM controller chips.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The build fails when the openssl/sha.h header file is not installed on
the host system. Fix this by setting the HOSTCCFLAGS variable to the
OpenWrt HOST_CFLAGS variable, without setting this the include paths and
other modifications in the host flags done by OpenWrt will be ignored by
the build.
This fixes the following build problem:
gcc -c -D_GNU_SOURCE -D_XOPEN_SOURCE=700 -Wall -Werror -pedantic -std=c99 -O2 -I../../include/tools_share fiptool.c -o fiptool.o
In file included from fiptool.h:16,
from fiptool.c:19:
fiptool_platform.h:19:11: fatal error: openssl/sha.h: No such file or directory
19 | # include <openssl/sha.h>
| ^~~~~~~~~~~~~~~
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The build of the manpages needs the pandoc tool, this is not in the
minimal requirements of OpenWrt, just remove the build of the restool
manpage. This fixes the build on systems without pandoc like the OpenWrt build bots.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Up to now the WPS script triggered WPS on the stations only if it
could not trigger it successfully on any hostapd instance.
In a Multi-AP context, there can be a need (to establish a new
wireless backhaul link) to trigger WPS on the stations, regardless of
whether there is already a hostapd instance configured or not. The
current script makes it impossible, as if hostapd is running and
configured, WPS would always be triggered on hostapd only.
To allow both possibilities, the following changes are made:
- Change the "pressed" action to "release", so that we can make use of
the "$SEEN" variables (to know for how long the button was pressed).
- If the button is pressed for less than 3 seconds, keep the original
behavior.
- If the button is pressed for 3 seconds or more, trigger WPS on the
stations, regardless of the status of any running hostapd instance.
- Add comments explaining both behaviors.
- While at it, replace the usage of '-a' with a '[] && []'
construct (see [1]).
This gives users a "fallback" mechanism to onboard a device to a
Multi-AP network, even if the device already has a configured hostapd
instance running.
[1]: https://github.com/koalaman/shellcheck/wiki/SC2166
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
this patch consolidates the amd64-microcode
(moved to linux-firmware.git, previously this was an extra
debian source package download), amdgpu and radeon firmwares
into a shared "amd" makefile.
With the upcoming 20211216 linux-firmware bump,
this will include a microcode update for ZEN 3 CPUs.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Otherwise, connection setup may fail due to JSON parse error in netifd.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[Updated commit description]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
PIN2 is used only to restrict changing of fixed dialling feature,
does not affect network registration. Therefore explicitly check for
PIN1 state during connection setup, which is required for network
registration.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[Updated commit description]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This is needed to properly close the control channel.
Otherwise, on the next try the caps call may fail.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
We were missing (not using) the last sector of each partition,
compared with the output of gparted.
Signed-off-by: Javier Marcet <javier@marcet.info>
[moved the dot]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The http://www.us.tcpdump.org mirror will go offline soon, only use the
normal download URL.
Reported-by: Denis Ovsienko <denis@ovsienko.info>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The rtl8723bs firmware was removed and a symlink to the rtl8723bu
firmware was created like it is done in upstream linux-firmware.
The following OpenWrt packages are changing:
* amdgpu-firmware: Multiple updates and new files
* ar3k-firmware: Multiple updates and new files
* ath10k-firmware-qca6174: Updated ath10k/QCA6174/hw3.0/board-2.bin
* bnx2x-firmware: Added bnx2x-e1-7.13.21.0.fw, bnx2x-e1h-7.13.21.0.fw and bnx2x-e2-7.13.21.0.fw
* iwlwifi-firmware-iwl8260c: Updated iwlwifi-8000C-36.ucode
* iwlwifi-firmware-iwl8265: Updated iwlwifi-8265-36.ucode
* iwlwifi-firmware-iwl9000: Updated iwlwifi-9000-pu-b0-jf-b0-46.ucode
* iwlwifi-firmware-iwl9260: Updated iwlwifi-9260-th-b0-jf-b0-46.ucode
* r8169-firmware: Updated rtl8153c-1.fw
* rtl8723bs-firmware: removed
* rtl8723bu-firmware: Added rtlwifi/rtl8723bs_nic.bin symlink
* rtl8822ce-firmware: Updated rtw8822c_fw.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Based on: 1ac627024d ("kernel: ath10k-ct: provide a build variant for
small RAM devices")
Like described in the ath10k-ct-smallbuffers version, oom-killer gets
triggered frequently by devices with small RAM.
That change is necessary for many community mesh networks which use
ath10k based devices with too little RAM. The -ct driver has been
proven unstable if used with 11s meshing and only wave2 chipsets are
supporting 11s. Freifunk Berlin is nowadays assembling its
firmware-based completely of vanilla OpenWRT with some package additions
which are made through the imagebuilder. Therefore we cannot take the
approach other freifunk communities have taken to maintain that patch
downstream [1]. Other communities consider these devices as broken and
that change would pretty much give those devices a second life [2].
[1] - 450b306e54
[2] - https://github.com/freifunk-gluon/gluon/issues/1988#issuecomment-619532909
Signed-off-by: Simon Polack <spolack+git@mailbox.org>
Signed-off-by: Nick Hainke <vincent@systemli.org>
The auto-ht option already kept HT and VHT support, but wasn't updated
to support HE (11ax).
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This device is based on NXP's QorIQ T2081QDS board, with a quad-core
dual-threaded 1.5 GHz ppc64 CPU and 4GB ECC RAM. The board has 5
ethernet interfaces, of which 3 are connected to the ethernet ports on
the front panel. The other 2 are internally connected to a Marvell
88E6171 switch; the other 5 ports of this switch are also connected to
the ethernet ports on the front panel.
Installation: write the sdcard image to an SD card. Stock U-Boot will
not boot, wait for it to fail then run these commands:
setenv OpenWrt_fdt image-watchguard-firebox-m300.dtb
setenv OpenWrt_kernel watchguard_firebox-m300-kernel.bin
setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; ext2load mmc 0:1 $fdtaddr $OpenWrt_fdt; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr - $fdtaddr'
saveenv
reset
The default U-Boot boot entry will now boot OpenWrt from the SD card.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Add a new target named "qoriq", that will support boards using PowerPC
processors from NXP's QorIQ brand.
This doesn't actually add support for any board yet, so that
installation instructions can go in the commit message of the commit
that adds actual support for a board.
Using CONFIG_E6500_CPU here due to the kernel using -mcpu=powerpc64
rather than -mcpu=e5500 when selecting CONFIG_E5500_CPU. The only
difference between e5500 and e6500 is AltiVec support, and the kernel
checks for it at runtime. Musl will only check at runtime if AltiVec
support is disabled at compile-time, so we need to use e5500 in CPU_TYPE
to avoid SIGILL.
Math emulation (CONFIG_MATH_EMULATION_HW_UNIMPLEMENTED) is required, as
neither e5500 nor e6500 implement fsqrt nor fsqrts, and musl hardcodes
sqrt and sqrtf to use these ASM instructions on PowerPC64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
Backport an upstream patch to make libunwind build on ppc64, and add
powerpc64 to the dependencies.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
As of version 3.7, Nettle added PowerPC64 assembly for several
algorithms. Unfortunately, they cause build to fail due to ABI mismatch:
gcm-hash.o: ABI version 1 is not compatible with ABI version 2 output
Disable assembler when ppc64 and musl are used for now.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Backport an upstream patch that adds support for ELFv2 ABI on big endian
ppc64. As musl only supports ELFv2 ABI on ppc64 regardless of
endianness, this is required to be able to build OpenSSL for ppc64be.
Modify our targets patch to add linux-powerpc64-openwrt, which will use
the linux64v2 perlasm scheme. This will probably break the combination
ppc64 with glibc, but as we really only want to support musl, this
shouldn't be a problem.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Provide incoming BSS transition queries to ubus subscribers.
This allows external steering daemons to provide clients with
an optimal list of transition candidates.
This commit has no functional state in case no ubus subscriber is
present or it does not handle this ubus message.
To prevent hostapd from sending out a generic response by itself, a
subscribing daemon has to return a non-zero response code to hostapd.
Signed-off-by: David Bauer <mail@david-bauer.net>
Backport a patch to allow extending the ubus BSS-transition method
for specifying individual dialog tokens for BSS transition
management requests.
This is required for handling BSS transition queries in the future.
Signed-off-by: David Bauer <mail@david-bauer.net>
39b584b Revert "dhcpv6: add a minimum valid lifetime for IA_PD updates"
c9578e1 dhcpv6: add support for null IA_PD valid lifetime
ca43ea3 dhcpv6: add a minimum valid lifetime for IA_PD updates
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5ca5e0b netifd: allow disabling rule/rule6 config sections
8875960 interface-ip: add support for IPv6 prefix invalidation
e589c05 interface-ip: use metric when looking for a route
b54ffde main: fix hotplug script usage message
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This adds a new struct for storing statistics not (yet) tracked by
hostapd regarding RRM and WNM activity.
These statistics can be read using the get_status hostapd interface ubus
method.
Signed-off-by: David Bauer <mail@david-bauer.net>
Revert a commit to allow providing CFLAGS and LIBS from OpenWrt package
Makefile.
This downgrades the nl80211.h to kernel 5.15 and removes FILS_CRYPTO_OFFLOAD.
This is needed to make it compatible with our patched mac80211 from
kernel 5.15
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The following patches were backported from upstream before and are not
needed any more:
package/kernel/mac80211/patches/ath10k/081-ath10k-fix-module-load-regression-with-iram-recovery-feature.patch
package/kernel/mac80211/patches/ath10k/980-ath10k-fix-max-antenna-gain-unit.patch
package/kernel/mac80211/patches/build/010-headers-Add-devm_platform_get_and_ioremap_resource.patch
package/kernel/mac80211/patches/subsys/300-mac80211-drop-check-for-DONT_REORDER-in-__ieee80211_.patch
package/kernel/mac80211/patches/subsys/307-mac80211-do-not-access-the-IV-when-it-was-stripped.patch
package/kernel/mac80211/patches/subsys/308-mac80211-fix-radiotap-header-generation.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Just update PKG_VERSION/PKG_MIRROR_HASH since fman-ucode
of LSDK-21.08 had no changes.
Switched to AUTORELEASE for simplicity.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Update layerscape u-boot package to LSDK-21.08 and drop patches which
are no longer needed.
The new env variable 'fsl_bootcmd_mcinitcmd_set' is needed to protect
the configured bootcmd and mc_init values. See [1] for more
informations.
[1] b62c174e86
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
fdt* utils are needed by targets that use U-Boot FIT images for
sysupgrade. It includes all recent BCM4908 SoC routers as Broadcom
switched from CFE to U-Boot.
fdtget is required for extracting images (bootfs & rootfs) from
Broadcom's ITB. Extracted images can be then flashed to UBI volumes.
sysupgrade is core functionality so it needs dtc as part of base code
base.
Cc: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
update rtl8812au-ct driver to be ready for 5.15 Linux.
Signed-off-by: Janpieter Sollie <janpieter.sollie@edpnet.be>
[added commit message from PR with changes, added tag to subject]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The 'fils_dhcp' option can be set to '*' in order to autodetect the DHCP server
For proto=dhcp networks, the discovered dhcp server will be used
For all other networks, udhcpc is called to discover the address
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Among other things, this can be used to auto-configure the DHCP server
address for wireless APs using FILS, if the bridged interface is
configured to DHCP
Signed-off-by: Felix Fietkau <nbd@nbd.name>
By default CONFIG_BTRFS_FS_POSIX_ACL is disabled, it should be enabled
only when you enable CONFIG_FS_POSIX_ACL.
Right now, when you enable CONFIG_FS_POSIX_ACL it will enable
CONFIG_BTRFS_FS_POSIX_ACL, but it will be disabled once you install
kmod-btrfs. This should prevent it.
Btrfs has enabled by default ACL for mount option.
More details:
https://cateee.net/lkddb/web-lkddb/BTRFS_FS_POSIX_ACL.htmlhttps://btrfs.wiki.kernel.org/index.php/Manpage/btrfs(5)
Signed-off-by: Josef Schlehofer <josef.schlehofer@nic.cz>
The following command checks if a instance of a service is running.
/etc/init.d/<service> running <instance>
In the variable `$@`, which is passed to the function
`service_running`, the first argument is always the `instance` which
should be checked. Because all other variables where removed from `$@`
with `shift`.
Before this change the first argument of `$@` was set to the `$service`
Variable. So the function does not work as expected. The `$service`
variable was always the instance which should be checked. This is not
what we want.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
71e08471ab56 mt76: eeprom: fix return code on corrected bit-flips
9a8fc6636d83 mt76: move sar_capa configuration in common code
7cdbea1dc82a mt76: only access ieee80211_hdr after mt76_insert_ccmp_hdr
678071ef7029 mt76: mt7615: clear mcu error interrupt status on mt7663
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch adds supports for the GL-B2200 router.
Specifications:
- SOC: Qualcomm IPQ4019 ARM Quad-Core
- RAM: 512 MiB
- Flash: 16 MiB NOR - SPI0
- EMMC: 8GB EMMC
- ETH: Qualcomm QCA8075
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
- WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
- INPUT: Reset, WPS
- LED: Power, Internet
- UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
- UART2: On board with BLE module
- SPI1: On board socket for Zigbee module
Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.
What's working:
- WiFi 2G, 5G
- WPA2/WPA3
Not tested:
- Bluetooth LE/Zigbee
Credits goes to the original authors of this patch.
V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade
Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adds generic support for sysupgrading on eMMC-based devices.
Provide function emmc_do_upgrade and emmc_copy_config to be used in
/lib/upgrade/platform.sh instead of redundantly implementing the same
logic over and over again.
Similar to generic sysupgrade on NAND, use environment variables
CI_KERNPART, CI_ROOTPART and newly introduce CI_DATAPART to indicate
GPT partition names to be used. On devices with more than one MMC
block device, CI_ROOTDEV can be used to specify the MMC device for
partition name lookups.
Also allow to select block devices directly using EMMC_KERN_DEV,
EMMC_ROOT_DEV and EMMC_DATA_DEV, as using GPT partition names is not
always an option (e.g. when forced to use MBR).
To easily handle writing kernel and rootfs make use of sysupgrade.tar
format convention which is also already used for generic NAND support.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CC: Li Zhang <li.zhang@gl-inet.com>
CC: TruongSinh Tran-Nguyen <i@truongsinh.pro>
a6451fea5a3d mt76: mt7615: improve wmm index allocation
1911486414dc mt76: mt7915: improve wmm index allocation
7998a41d1321 mt76: clear sta powersave flag after notifying driver
664475574438 mt76: mt7603: introduce SAR support
5c0da39c940b mt76: mt7915: introduce SAR support
77fc6c439a32 mt76: mt7603: improve reliability of tx powersave filtering
094b3d800835 firmware: update mt7663 rebb firmware to 20200904171623
25237b19bcc1 mt76: eeprom: tolerate corrected bit-flips
1463cb4c6ac2 mt76: mt7921: fix boolreturn.cocci warning
586bad6020f7 mt76: mt7921: use correct iftype data on 6GHz cap init
8ec95c910425 mt76: mt7921s: fix bus hang with wrong privilege
688e30c7d854 firmware: update mt7921 firmware to version 20211014
6fad970893dd mt76: fix key pointer overwrite in mt7921s_write_txwi/mt7663_usb_sdio_write_txwi
95acf972750c mt76: fix 802.3 RX fail by hdr_trans
3f402b0cf6c0 mt76: mt7921s: fix possible kernel crash due to invalid Rx count
929a03a8d65d mt76: connac: fix last_chan configuration in mt76_connac_mcu_rate_txpower_band
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch is a revert of the upstream patch to Debian's ca-certificate
commit 033d52259172 ("mozilla/certdata2pem.py: print a warning for expired certificates.")
The reason is, that this change broke builds with the popular
Ubuntu 20.04 LTS (focal) releases which are shipping with an
older version of the python3-cryptography package that is not
compatible.
|Traceback (most recent call last):
| File "certdata2pem.py", line 125, in <module>
| cert = x509.load_der_x509_certificate(obj['CKA_VALUE'])
|TypeError: load_der_x509_certificate() missing 1 required positional argument: 'backend'
|make[5]: *** [Makefile:6: all] Error 1
...or if the python3-cryptography was missing all together:
|Traceback (most recent call last):
| File "/certdata2pem.py", line 31, in <module>
| from cryptography import x509
|ModuleNotFoundError: No module named 'cryptography'
More concerns were raised by Jo-Philipp Wich:
"We don't want the build to depend on the local system time anyway.
Right now it seems to be just a warning but I could imagine that
eventually certs are simply omitted of found to be expired at
build time which would break reproducibility."
Link: <https://github.com/openwrt/openwrt/commit/7c99085bd697>
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Reported-by: Shane Synan <digitalcircuit36939@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
When compiling with CONFIG_USE_RFKILL=y, the build fails and mentions that
dependency on kmod-rfkill is missing, which is correct [1]. Add this
dependency to the Makefile.
Depend on +USE_RFKILL and not PACKAGE_kmod-rfkill, because it forces
selection of kmod-rfkill package. Other combinations in DEPENDS like
USE_RFKILL:kmod-rfkill or (+)PACKAGE_kmod-rfkill:kmod-rfkill do not force
selection of kmod-rfkill package.
The kmod-rfkill package itself depends on USE_RFKILL, so with +USE_RFKILL
in kmod-cfg80211 package it is not possible to select wrong combination of
packages.
[1] https://linux-wireless.vger.kernel.narkive.com/m8JY9Iks/cfg80211-depends-on-rfkill-or-not
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
If spectral scan support is enabled then ath10k-ct will cause a NULL
pointer due to relay_open() being called with a const callback struct
which is only supported in kernel 5.11 and later.
So, simply check the kernel version and if 5.11 and newer use the const
callback struct, otherwise use the regular struct.
Fixes: 553a3ac ("ath10k-ct: use 5.15 version")
Signed-off-by: Robert Marko <robimarko@gmail.com>
The configs/omap3_overo_defconfig file was removed from upstream U-Boot
in commit ed3294d6d1f9 ("arm: Remove overo board"). Remove it in OpenWrt
too. If someone needs this please add it also to upstream U-Boot.
This fixes the compile of the omap target.
Fixes: ffb807ec90 ("omap: update u-boot to 2021.07")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for the Teltonika RUTX10.
This device is an industrial DIN-rail router with 4 ethernet ports,
2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs.
The RUTX series devices are very similiar so common parts of the DTS
are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev
board.
See https://teltonika-networks.com/product/rutx10 for more info.
Hardware:
SoC: Qualcomm IPQ4018
RAM: 256MB DDR3
SPI Flash 1: XTX XT25F128B (16MB, NOR)
SPI Flash 2: XTX XT26G02AWS (256MB, NAND)
Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
USB Hub: Genesys Logic GL852GT
Bluetooth: Qualcomm CSR8510 (A10U)
LED/GPIO controller: STM32F030 with custom firmware
Buttons: Reset button
Leds: Power (green, cannot be controlled)
WiFi 2.4G activity (green)
WiFi 5G activity (green)
MACs Details verified with the stock firmware:
eth0: Partition 0:CONFIG Offset: 0x0
eth1: = eth0 + 1
radio0 (2.4 GHz): = eth0 + 2
radio1 (5.0 GHz): = eth0 + 3
Label MAC address is from eth0.
The LED/GPIO controller needs a separate kernel driver to function.
The driver was extracted from the Teltonika GPL sources and can be
found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt
USB detection of the bluetooth interface is sometimes a bit flaky. When
not detected power cycle the device. When the bluetooth interface was
detected properly it can be used with bluez / bluetoothctl.
Flash instructions via stock web interface (sysupgrade based):
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
5. Open stock web interface at http://192.168.1.1
6. Set some password so the web interface is happy
7. Go to firmware upgrade settings
8. Choose
openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi
9. Set 'Keep settings' to off
10. Click update, when warned that it is not a signed image proceed
Return to stock firmware:
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
Note: The DTS expects OpenWrt to be running from the second rootfs
partition. u-boot on these devices hot-patches the DTS so running from the
first rootfs partition should also be possible. If you want to be save follow
the instructions above. u-boot HTTP recovery restores the device so that when
flashing OpenWrt from stock firmware it is flashed to the second rootfs
partition and the DTS matches.
Signed-off-by: Felix Matouschek <felix@matouschek.org>
Add back support for the TLC591xx series LEDs which are used in the
ipq806x-based Meraki Cryptid series devices.
This module previously existed for the mvebu platform but was removed
at commit f849c2c832 due to being enabled
in that platform's kernel config.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD
(hAP ac³), a indoor dual band, dual-radio 802.11ac
wireless AP with external omnidirectional antennae, USB port, five
10/100/1000 Mbps Ethernet ports and PoE passthrough.
See https://mikrotik.com/product/hap_ac3 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4019
- RAM: 256 MB
- Storage: 16 MB NOR + 128 MB NAND
- Wireless:
· Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
· Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae
- Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in, PoE passtrough on port 5
- 1x USB Type A port
Installation:
1. Boot the initramfs image via TFTP
2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1"
3. Use ubiformat to remove MikroTik specific UBI volumes
* Detach the UBI partition by running: "ubidetach -d 0"
* Format the partition by running: "ubiformat /dev/mtdN -y"
Replace mtdN with the correct mtd index from step 2.
3. Flash the sysupgrade image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
Tested-by: Mark Birss <markbirss@gmail.com>
Tested-by: Michael Büchler <michael.buechler@posteo.net>
Tested-by: Alex Tomkins <tomkins@darkzone.net>
Currently nand_upgrade_tar() will pass the kernel length
to nand_upgrade_prepare_ubi() in all cases except for when
the kernel is to be installed in a separate partition as a
binary with the MTD tool.
While this is fine for almost all cases newer MikroTik NAND
devices like hAP ac3 require the kernel to be installed as a
UBIFS packed UBI volume in its own partition.
So, since we have a custom recipe to use ubiformat to flash
the kernel in its partition it makes no sense for sysupgrade
to also install the kernel as a UBI volume in the "ubi"
partition as it only wastes space and will never be used.
So, simply check whether CI_KERNPART is set to "none" and
if so unset the "has_kernel" variable which will in turn
prevent the kernel length from being passed on and then
the kernel UBI volume wont be created for no usefull purpose.
The ath79 MikroTik NAND target has been setting CI_KERNPART
to "none" for a while now altough that was not preventing
the kernel to be installed as UBI volume as well.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update ath10k-ct to get the upstream fix for
DFS support for VHT160 in the 5.15 based ath10k-ct.
(Switch from 5.10 to 5.15 surfaced the upstream regression.)
* refresh one patch
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Follow up to commit 565b62cca2. Managed to
hit the very same issue again while playing with the NOR SPL builds.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With cryptocpp in place we can now update past the point of dropping
the old tbb_linux binary and build it instead.
Hauke confirmed that this also allows this firmware to be built on
aarch64.
97f01f5 Wtpdownloader: Properly retrieve current tty options
a33ff86 Wtpdownloader: Set CREAD tty cflag
af461d2 Wtpdownloader: Fix stuck during opening UART tty device
38c2135 Makefile: Print error when specified CLOCKSPRESET is not valid
f014428 TBB: Remove out-of-dated x86-64 ELF binary tbb_linux
1b6cb50 TBB: Fix compilation with Crypto++ 5.6.5
d9fb291 TBB: Fix memory corruptions by calling correct delete[] operator
d575885 TBB: Fix initializing CCTIM object
b9e1c4e Wtpdownloader: Fix makefile
8f61591 Wtpdownloader: Fix building with gcc 11
eabea5f TBB: Fix building with gcc 11
Signed-off-by: Andre Heider <a.heider@gmail.com>
Based on the Build Instructions for Trusted-Firmware-A [1],
there is a required cryptopp [2].
In the past, it used 'tbb_linux' image tool binary, which seems to
be buggy, deprecated and removed from A3700-utils-marvell and it should
not be used anymore. That's why I removed 001-imagetool.patch, which is
no longer necessary.
[1] https://trustedfirmware-a.readthedocs.io/en/v2.5/plat/marvell/armada/build.html
[2] https://cryptopp.com/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
without this patch a3700-utils/tim/ddr/ddr_tool.verstr contains the OpenWrt commit ID.
this patch fix the mv_ddr version commit ID by using the global variable MV_DDR_COMMIT_ID.
Upon boot it now prints "mv_ddr-devel-g02e23dbc-d DDR4 16b 1GB 1CS".
Cc: Andre Heider <a.heider@gmail.com>
Signed-off-by: Kerma Gérald <gandalf@gk2.net>
We switched to mac80211 5.15 backport version.
Also switch ath10k-ct to 5.15 and drop the mac address patch
that got merged upstream.
Compile and tested on ipq806x Netgear R7800.
Also update the ath10k-ct to latest version to fix a typo
for the new version in the kernel log.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Add the beacon interval to hostapd status output. This allows external
services to discover the beacon interval for a specific VAP.
This way, external wireless management daemons can correctly calculate
fields containing TBTT value from absolute time-values.
Signed-off-by: David Bauer <mail@david-bauer.net>
If authentication fails repeatedly e.g. because of a weak signal, the link
can end up in blocked state. If one of the nodes tries to establish a link
again before it is unblocked on the other side, it will block the link to
that other side. The same happens on the other side when it unblocks the
link. In that scenario, the link never recovers on its own.
To fix this, allow restarting authentication even if the link is in blocked
state, but don't initiate the attempt until the blocked period is over.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some drivers that do their own sequence number allocation (e.g. ath9k, mwlwifi) rely
on being able to modify params->ssn on starting tx ampdu sessions.
This was broken by a change that modified it to use sta->tid_seq[tid] instead.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When procd-ujail is available, 1f78538387 runs hostapd as user
"network", with only limited additional capabilities (CAP_NET_ADMIN and
CAP_NET_RAW).
hostapd_cli (CONFIG_PACKAGE_hostapd-utils) communicates with hostapd
over a named UNIX-domain socket. hostapd_cli is responsible for creating
this socket at /tmp/wpa_ctrl_$pid_$counter. Since it typically runs as
root, this endpoint is normally created with uid root, gid root, mode
0755. As a result, hostapd running as uid network is able to receive
control messages sent through this interface, but is not able to respond
to them. If debug-level logging is enabled (CONFIG_WPA_MSG_MIN_PRIORITY
<= 2 at build, and log_level <= 2 in /etc/config/wireless wifi-device),
this message will appear from hostapd:
CTRL: sendto failed: Permission denied
As a fix, hostapd_cli should create the socket node in the filesystem
with uid network, gid network, mode 0770. This borrows the presently
Android-only strategy already in hostapd intended to solve the same
problem on Android.
If procd-ujail is not available and hostapd falls back to running as
root, it will still be able to read from and write to the socket even if
the node in the filesystem has been restricted to the network user and
group. This matches the logic in
package/network/services/hostapd/files/wpad.init, which sets the uid and
gid of /var/run/hostapd to network regardless of whether procd-ujail is
available.
As it appears that the "network" user and group are statically allocated
uid 101 and gid 101, respectively, per
package/base-files/files/etc/passwd and USERID in
package/network/services/hostapd/Makefile, this patch also uses a
constant 101 for the uid and gid.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
[refreshed patch]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix the return value, shell return codes should be 0 to indicate success
(i.e. mount point found), 1 should be failure (i.e. mount point not-found).
Fixes: ac4e8aa ("dnsmasq: fix more dnsmasq jail issues")
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
Extend the hotplug.json ruleset to setup the common /dev/std{in,out,err}
symbolic links which are needed by some applications, e.g. nftables when
applying rulesets from stdin.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
8de12de system: add diskfree infos to ubus
bf3fe0e service: move jail parsing to end of instance parser
87b5836 procd: add full service shutdown prior to sysupgrade
01ac2c4 procd: service_stop_all: also kill inittab actions
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
5dd32475c859 mt76: mt7915: get rid of mt7915_mcu_set_fixed_rate routine
f5cfaaff3dd1 mt76: mt7921: drop offload_flags overwritten
f5ad840ca5c0 mt76: mt7615: fix possible deadlock while mt7615_register_ext_phy()
29a8a08827b1 mt76: mt7921: fix MT7921E reset failure
f44685f2faee mt76: mt7915: fix return condition in mt7915_tm_reg_backup_restore()
ae8e02ddd2b0 mt76: mt7915: fix SMPS operation fail
e814e15716b0 mt76: reverse the first fragmented frame to 802.11
c9bca3ed9566 mt76: mt7915: fix NULL pointer dereference in mt7915_get_phy_mode
dd054b7e16e7 mt76: only set rx radiotap flag from within decoder functions
f1520c9bb332 mt76: mt7915: add default calibrated data support
0c489ea2865a mt76: testmode: add support to set MAC
91c5da3d0a7c mt76: mt7921: add support for PCIe ID 0x0608/0x0616
ca39b4bbc227 mt76: debugfs: fix queue reporting for mt76-usb
00b6f497e2e8 mt76: mt7921: introduce 160 MHz channel bandwidth support
c1574466c733 mt76: fix possible OOB issue in mt76_calculate_default_rate
9680a17b0aed mt76: mt7921: fix possible NULL pointer dereference in mt7921_mac_write_txwi
78fc0dcdcef0 mt76: connac: fix a theoretical NULL pointer dereference in mt76_connac_get_phy_mode
05953e7d6fe7 mt76: mt7615: remove dead code in get_omac_idx
39f6c37127c1 mt76: connac: remove PHY_MODE_AX_6G configuration in mt76_connac_get_phy_mode
526591b203f3 mt76: do not pass the received frame with decryption error
256789bb400f mt76: fix the wiphy's available antennas to the correct value
fa187f5cf068 mt76: fix timestamp check in tx_status
11ebf11a3587 mt76: mt7915: fix the wrong SMPS mode
8c69b815ee7f mt76: mt7921: honor mt76_connac_mcu_set_rate_txpower return value in mt7921_config
bc6798f729f9 mt76: move sar utilities to mt76-core module
b1d0ad2e74fe mt76: mt76x02: introduce SAR support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Allows to avoid rpath hacks with at least softethervpn.
--with-pic is needed as it's not default with static libraries, only
shared ones.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
cce5e35 vlist: define vlist_for_each_element_safe
This is change affects only a macro in headers and hence it is not
required to bump ABI_VERSION.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
68961a555e42 ubus: drop dnsmasq check for dns_result method
1ca3e26b8169 bpf: refactor code to support explicit opt-in for bulk+prio detection
3f0acf039f41 bpf: move flow prio/bulk detection config into a separate data structure
bc54c97e3333 map, bpf: create a separate map for configured dscp classes
46cf3eae2d99 bpf: fix bulk flow detaction
88f1db7dd611 bpf: fix priority flow detection
b5dec7874373 bpf: remove access to skb->gso_size
e728a319a9a5 interface: unify status, always include ifname, ingress, egress
Signed-off-by: Felix Fietkau <nbd@nbd.name>
BTF pointer data has a different size on 32 vs 64 bit targets,
and while the generated eBPF code works, the BTF data fails to validate
on mismatch
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since sqm-scripts and qos-scripts packages are in the same category as qosify,
the firsts being in the Base System category, I find it understandable to move
the latter to Base System instead of network section.
Signed-off-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
On systems using brmcfmac (e.g. Raspberry Pi Zero W) without this fix,
the final setup-call:
iw dev wlan0 ibss join ...
fails with returncode 161 and message:
"command failed: Not supported (-95)"
So this patch calls an explicit:
iw dev wlan0 set type ibss
just prior to the 'ibss join' command.
I have tested several ath9k and mt76xx devices
with different revisions: this patch does not harm.
please also apply to stable branch.
Signed-off-by: Bastian Bittorf <bb@npl.de>
Update Telekom Speedport W921V firmware download URL.
Contained TAPI and VDSL firmware blobs are identical.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
19aae94 [build: avoid rebuilds of unset VARIANT packages] builds
packages defined without a VARIANT only once, using the first VARIANT
defined in the Makefile.
This caused problems with wpa-cli, as it is only built for variants that
include supplicant support, and the first VARIANT defined may not build
it.
The same happens to hostapd-utils, which is not built for
supplicant-only variants.
To circumvent this, set VARIANT=* for both packages so that they get
built for every defined variant. This should not cause spurious
rebuilds, since tey are not a dependency of any other package defined in
this Makefile.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
On lantiq a lot of stuff expects to be loaded to and executed at
0x80002000, including our own second stage bootloader.
For all build u-boots, the initial stack pointer is at 0x80008000. After
loading data to 0x80002000, every further stack operation corrupts the
loaded code.
Set the initial stack pointer to 0x80002000, to not overwrite code
loaded in memory. A stack of 0x2000 bytes has been proven as enough in
all done tests.
Signed-off-by: Mathias Kresin <dev@kresin.me>
On danube we only have 0x6800 bytes of usable SRAM. Everything behind
can't be written to and a SPL u-boot locks up during boot.
Since it's a hard to debug issue and took me more than two years to fix
it, I consider it worth to include fix albeit SPL u-boots are not build
in OpenWrt.
I faced the issue while trying to shrink the u-boot to 64K since some
boards only have an u-boot partition of that size from the days
ifx-uboot was used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With gcc10 the variables are placed more tightly to each other, which
uncovers a long existing bug in the lantiq DMA code. It can be observed
when using tftpboot with the filename parameter, which gets reset during
the tftpboot execution.
NetRxPackets[] points to cache line size aligned addresses. In
ltq_eth_rx_packet_align() the address NetRxPackets[] points to is
increased by LTQ_ETH_IP_ALIGN and the resulting not cache aligned
address is used further on. While doing so, the length/size is never
updated.
The "not cache aligned address" + len/size for a cache aligned address
is passed to invalidate_dcache_range(). Hence, invalidate_dcache_range()
invalidates the next 32 bit as well, which flashes the BootFile variable
as well.
variable BootFile is at address: 0x83ffe12c
NetRxPackets[] points to 0x83ffdb20 (len is 0x600)
data points to: 0x83ffdb22 (len is 0x600)
ltq_dma_dcache_inv: 0x83ffdb22 (for len 0x600)
invalidate_dcache_range: 0x83ffdb20 to 0x83ffe120 (size: 32)
invalidate_dcache_range: 0x83ffdb20 to 0x83ffdb40 (Bootfile: a.bin)
...
invalidate_dcache_range: 0x83ffe100 to 0x83ffe120 (Bootfile: a.bin)
invalidate_dcache_range: 0x83ffe120 to 0x83ffe140 (Bootfile: )
In ltq_dma_tx_map() and ltq_dma_rx_map() the start address passed to
ltq_dma_dcache_wb_inv() is incorrect. By considering the offset, the
start address passed to flush_dcache_range() is always aligned to 32, 64
or 128 bytes dependent on configured DMA burst size.
Fixes: FS#4113
Signed-off-by: Mathias Kresin <dev@kresin.me>
At least since gcc 7.3.0 (OpenWrt 18.06) lwr/lwl are used in the
assembly of LzmaProps_Decode. While the decission made by the compiler
looks perfect fine, it triggers some obscure hang on lantiq danube-s
v1.5 with MX29LV640EB NOR flash chips.
Only if the offset 1 is used, the hang can be observed. Using any other
offset works fine:
lwl s0,0(a1) - s0 == 0x6d000080
lwl s0,1(a1) - hangs
lwl s0,2(a1) - s0 == 0x0080xxxx
lwl s0,3(a1) - s0 == 0x80xxxxxx
It isn't clear whether it is a limitation of the flash chip, the EBU or
something else.
Force 8bit reads to prevent gcc optimizing the read with lwr/lwl
instructions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
P&W R619AC is a IPQ4019 Dual-Band AC1200 router.
It is made by P&W (p2w-tech.com) known as P&W R619AC
but marketed and sold more popularly as G-DOCK 2.0.
Specification:
* SOC: Qualcomm Atheros IPQ4019 (717 MHz)
* RAM: 512 MiB
* Flash: 16 MiB (NOR) + 128 MiB (NAND)
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN)
* Wireless:
- 2.4 GHz b/g/n Qualcomm Atheros IPQ4019
- 5 GHz a/n/ac Qualcomm Atheros IPQ4019
* USB: 1 x USB 3.0
* LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED)
* Input: 1 x reset
* 1 x MicroSD card slot
* Serial console: 115200bps, pinheader J2 on PCB
* Power: DC 12V 2A
* 1 x Unpopulated mPCIe Slot (see below how to connect it)
* 1 x Unpopulated Sim Card Slot
Installation:
1. Access to tty console via UART serial
2. Enter failsafe mode and mount rootfs
<https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset>
3. Edit inittab to enable shell on tty console
`sed -i 's/#ttyM/ttyM/' /etc/inittab`
4. Reboot and upload `-nand-factory.bin` to the router (using wget)
5. Use `sysupgrade` command to install
Another installation method is to hijack the upgrade server domain
of stock firmware, because it's using insecure http.
This commit is based on @LGA1150(at GitHub)'s work
<a4932c8d5a>
With some changes:
1. Added `qpic_bam` node in dts. I don't know much about this,
but I observed other dtses have this node.
2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not
working. This fix is from
<51143b4c75>
3. Removed the 32MB NOR variant.
4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes
wlan2g led light up.
5. Added ethphy led config in dts.
6. Changed nand partition label from `rootfs` to `ubi`.
About the 128MiB variant: The stock bootloader sets size of nand to 64MiB.
But most of this devices have 128MiB nand. If you want to use all 128MiB,
you need to modify the `MIBIB` data of bootloader. More details can be
found on github:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060>
For instructions on how to flash the MIBIB partition from u-boot console:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232>
About the Mini PCIe slot: (from "ygleg")
"The REFCLK signals on the Mini PCIe slot is not connected on
this board out of the box. If you want to use the Mini PCIe slot
on the board, you need to (preferably) solder two 0402 resistors:
R436 (REFCLK+) and R444 (REFCLK-)..."
This and much more information is provoided in the github comment:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670>
Signed-off-by: Richard Yu <yurichard3839@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
[Added comment about MIBIB+128 MiB variant. Added commit
message section about pcie slot. Renamed gpio-leds' subnodes
and added color, function+enum properties.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
eb0a3ee fw4.uc: Do not quote port ranges
c5a8e3e tests: adapt test to new ICMP print logic
Also start using $(AUTORELEASE)
Signed-off-by: Paul Spooren <mail@aparcar.org>
Simply reading /proc/*/stat as a space-separated string will not work
as the process name may itself contain spaces. Hence we must match on
the '(' and ')' characters around the process name and can then handle
the remaining string as space-separated values.
This fixes shell error messages which have been popping up the console
due to spaces in process names being interpreted as field separators.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The nl80211_set_wiphy() function was changed between kernel 5.11 and
5.12 to take the rdev->wiphy lock which should be freed at the end
again. The 500-mac80211_configure_antenna_gain.patch added some code
which just returned in some cases without unlocking. This resulted in a
deadlock with brcmfmac.
This patch fixes this by also jumping to the out label in case we want
to leave the function.
This fixes a hanging system when brcmfmac is in use. I do not know why
we do not see this with other driver.
The kernel returns very useful debug details when setting these OpenWrt
configuration options:
CONFIG_KERNEL_DETECT_HUNG_TASK=y
CONFIG_KERNEL_PROVE_LOCKING=y
Fixes: FS#4122
Fixes: b96c2569ac ("mac80211: Update to version 5.12.19-1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
from https://git.kernel.org/pub/scm/network/iproute2/iproute2.git
changes since 5.14.0:
ad3a118f rdma: Fix SRQ resource tracking information json
7a235a10 man: devlink-port: fix pfnum for devlink port add
229eaba5 uapi: pickup fix for xfrm ABI breakage
a500c5ac lib/bpf: fix map-in-map creation without prepopulation
7c032cac man: devlink-port: remove extra .br
04ee8e6f man: devlink-port: fix style
14802d84 man: devlink-port: fix the devlink port add synopsis
897772a7 cmd: use spaces instead of tabs for usage indentation
e7a98a96 mptcp: unbreak JSON endpoint list
2f5825cb lib: bpf_legacy: fix bpffs mount when /sys/fs/bpf exists
d756c08a tc/f_flower: fix port range parsing
92e32f77 uapi: updates from 5.15-rc1
e7e0e2ce iptuntap: fix multi-queue flag display
deef844b man: ip-link: remove double of
a3272b93 configure: restore backward compatibility
ceba5930 tree-wide: fix some typos found by Lintian
7a705242 ip: remove leftovers from IPX and DECnet
8ab1834e uapi: update headers from 5.15 merge
6d0d35ba ip/bond: add lacp active support
926ad641 Update kernel headers
c730bd0b ip/tunnel: always print all known attributes
df8912ed ipioam6: use print_nl instead of print_null
7e7270bb tc/skbmod: Introduce SKBMOD_F_ECN option
86c596ed IOAM man8
2d83c710 New IOAM6 encap type for routes
f0b3808a Add, show, link, remove IOAM namespaces and schemas
acbdef93 Import ioam6 uapi headers
2d6fa30b Update kernel headers
508ad89c ipneigh: add support to print brief output of neigh cache in tabular format
* update patch 170-ip_tiny.patch to accomodate ioam.
Signed-off-by: Russell Senior <russell@personaltelco.net>
0750f2b4d329 README: dnsmasq integration is complete
8e48d0b0cbba bpf: add initial support for splitting map dscp value into ingress and egress
bfc2cafe2a8c map: add support for defining aliases
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We can't use booleans, since we're not including stdbool.h. Use integers
instead.
Fixes: 0b79e7c01e ("dnsmasq: generate the dns object name dynamically")
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
dnsmasq may call hotplug.dhcp, hotplug.neigh and hotplug.tftp.
Only the first two callees were listed in the ACL, so add missing
hotplug.tftp.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
9d1431e jail: allow passing environment variable to procd jailed process
Fixes dnsmasq in ujail which needs USER_SCRIPT env variable to be
passed to jailed process.
Reported-by: Bastian Bittorf <bb@npl.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When __ieee80211_select_queue is called, skb->cb has not been cleared yet,
which means that info->control.flags can contain garbage.
In some cases this leads to IEEE80211_TX_CTRL_DONT_REORDER being set, causing
packets marked for other queues to randomly end up in BE instead.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
1fdf2a3 Fix kernel panic due to device deletion (#29)
e7b48d1 add the mutex lock for create/delete/config/insert nat46 devices to fix nat46 module crash issues. (#28)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
A set of tags can be specified for --dhcp-host option to restrict the
assignment to the requests which match all the tags.
Example usage:
config vendorclass
option networkid 'udhcp'
option vendorclass 'udhcp'
config host
option mac '*:*:*:*:*:*'
list match_tag 'switch.10'
list match_tag 'udhcp'
option ip '192.168.25.10'
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Now that wildcard matching is supported, this makes it easier for packages
to supply their own qosify rules
Signed-off-by: Felix Fietkau <nbd@nbd.name>
737970946bc0 map: default to fnmatch matching for dns patterns. support regex via leading /
b56b112e62e2 ubus: fix crash caused by missing static keyword
3a420e272c18 qosify: support wildcards in classifier filenames
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When installing additional rpcd modules, a restart of rpcd is required.
This often confuses users as even after installing rpcd-mod-rpcsys the
relevant ubus objects are still missing until rpcd has been reloaded
(or the system has been rebooted, obviously).
Let rpcd-mod-* reload rpcd as post-install action.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2ca7352543da map: make a helper function for freeing entries
411432ec853b map: add support for adding dns regex patterns
14803cb559d8 ubus: remove unused enum
a0740172eda6 ubus: add api for providing dns lookup results for dns regex rules
406fbf478e87 ubus: add support for dynamically adding dns based rules
5fc91183d60a README: mention dns regex entries
3ed8c3eb1a3b README: document mapping file syntax
91ce2e77d302 map: introduce low effort codepoint from RFC8622
5ff14acca0e7 interface: enable NAT on interfaces by default
e70f70e496d7 README: fix typo
f25ded617478 README: fix another typo
675238bc2ce5 loader: always reinitialize programs
010eea0d98c3 map: improve timeout handling of IP entries
7ef54a7f04a0 map: add DF codepoint
6f7fbe698555 map: increase active timeout to 300
60e06a579a13 qosify-bpf: inline check_flow() to ensure that it is jited
f5ae89e8d869 ubus: subscribe to dnsmasq.dns for dns lookup results
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With "getting WIFI MAC from NVMEM" working on ath79 on 5.10,
the next logical step I think is to utilize nvmem subsystem
to also get the calibration data from there.
This will tremendously speed up the wifi bring-up, since
we no longer need the userspace helper for the simple
devices that can just load them from there.
included with this patch is a package/mac80211/refresh.
Tested on: WNDR3700v2, TP-Link Archer C7v2
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
e303ba8 uqmi: update code generator
7880de8 uqmi: sync data from libqmi project
d647f8d uqmi: add more diagnostics commands
6f95626 uim: add --uim-get-sim-state
Use newly introduce --uim-get-sim-state command to query PIN status
from modems which require using uim instead of dms command for that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20bf958 session: use uloop_timeout_remaining64
d11ffe9 session: use blobmsg_get_u64 for RPC_DUMP_EXPIRES
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Support for libsanitizer on MIPS 32 and MIPSEL 32 was added with GCC 9.
MIPS 64 and ARC are still not supported.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This version has some improvements for musl.
This version works fine for me on MIPS 32 BE without MIPS16 even on musl.
The additional patch is needed to make valgrind use the correct syscall
numbers for new syscalls like clock_gettime64. The MIPS architecture
uses special syscall ranges which are different from most other systems.
The patch is pending upstream: https://bugs.kde.org/show_bug.cgi?id=444781
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This implements the mapping recommendations from RFC8325, with an
update from RFC8622. This ensures that DSCP marked packets are properly
sorted into WMM classes.
The map can be disabled by setting iw_qos_map_set to something invalid
like 'none'
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Subtarget-specific files under 'uboot-envtools' package are supported
since 6f3a05ebb0 ("uboot-envtools: support uci-default config also per
subtargets").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
It relies on a custom ax_code_coverage.m4 file included with strace.
Unfortunately, this conflicts with the one included with
autoconf-macros. Instead of creating a huge patch to fix it, just remove
the variable as code coverage is not used here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Build the tc-mod-iptables before the tc-tiny and tc-full packages.
This avoids unnecessary package rebuild when calling make back to back.
Before this change, tc-mod-iptables will be built after the main tc
binary packages.
Both tc-tiny and tc-full depend on tc-mod-ipables. If make is called
after the packages are already built, it will check the timestamps of
both packages, and will rebuild the main binaries, since the module
package will be newer than the tc package.
Calling BuildPackage,mod-iptables first ensures that its variant gets
built before the other packages' variants.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Set the different libf2fs packages's VARIANT, so that the right settings
will be used by each different variant, if they are both being built.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Package hostapd-common is a dependency of every other package defined in
hostpad Makefile. It is currently built next to the bottom of that
Makefile's package list.
If you run make back to back, then check-compile will compare the
hostapd-common timestamp to the variant being compiled, to decide if the
varint needs to be rebuilt or not. Since the hostapd-conf package is
built towards the end of the list, it will be newer than most of the
variants, causing unnecessary package rebuilds.
Move it to the top, so that its timestamp will be older than dependent
packages, avoiding unnecessary rebuild of every selected variant.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
19fd7fc libfstools: make sure file is closed on error
d390744 libfstools: use uevent instead of relying on custom kernel patch
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
find_mmc_part provides a better alternative and all users of
get_partition_by_name have been removed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some devices got more than one mmc device.
Allow specifying the root device as 2nd parameter of find_mmc_part so
scripts can avoid matching irrelevant partitions on wrong mmc device.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
qosify is simple daemon for setting up and managing CAKE along with a custom
eBPF based classifier that sets DSCP fields of packets.
It is configured via UCI and it supports the following features:
- simple TCP/UDP port based mapping
- IP address based mapping
- priority boosting based on average packet size
- bulk flow detection based on number of packets per second
- dynamically add IP entries with timeout
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to genererate suitable kernel headers, a 5.10 kernel tree is
prepared with a default config for mips. The arch is forced to mips in
order to avoid issues with inline asm on various architectures in a way
that doesn't involve relying on the host toolchain/headers.
It also has the advantage of supporting both endian types
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Commit a2fcd3900c ("dnsmasq: improve init script") broke the existing
handling for hosts_dir. Remove the redundant mount again to fix it.
Reported-by: Hartmut Birr <e9hack@gmail.com>
Fixes: a2fcd3900c ("dnsmasq: improve init script")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
b743a331421d ubusd: log ACL init errors
2099bb3ad997 libubus: use list_empty/list_first_entry in ubus_process_pending_msg
ef038488edc3 libubus: process pending messages in data handler if stack depth is 0
a72457b61df0 libubus: increase stack depth for processing obj msgs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Added minimal mmc support for helper functions:
- find_mmc_part: Look for a given partition name. Returns the
coresponding partition path
- caldata_extract_mmc: Look for a given partition name and then
extracts the calibration data
- mmc_get_mac_binary: Returns the mac address from a given partition
name and offset
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[replace dd with caldata_dd, moved sysupgrade mmc to orbi]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
When loading the bonding driver, bonding interface are automatically
created on bonding module load.
> ip a s bond0
> 14: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
> group default qlen 1000
> link/ether a6:f2:20:64:c1:b9 brd ff:ff:ff:ff:ff:ff
This is not necessary in openwrt as we do not use this created interface.
The netifd creates a bonding interface based on its network configuration
name and configures this over the netifd bonding proto handler.
In order to keep the overview of the interfaces clear, bonding
interfaces should not be created automatically when loading this module,
because they are not used anyway.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Dongwon T&I DW02-412H is a 2.4/5GHz band 11ac (WiFi-5) router, based on
Qualcomm Atheros QCA9557.
Specifications
--------------
- SoC: Qualcomm Atheros QCA9557-AT4A
- RAM: DDR2 128MB
- Flash: SPI NOR 2MB (Winbond W25Q16DVSSIG / ESMT F25L16PA(2S)) +
NAND 64/128MB
- WiFi:
- 2.4GHz: QCA9557 WMAC
- 5GHz: QCA9882-BR4A
- Ethernet: 5x 10/100/1000Mbps
- Switch: QCA8337N-AL3C
- USB: 1x USB 2.0
- UART:
- JP2: 3.3V, TX, RX, GND (3.3V is the square pad) / 115200 8N1
Installation
--------------
1. Connect a serial interface to UART header and
interrupt the autostart of kernel.
2. Transfer the factory image via TFTP and write it to the NAND flash.
3. Update U-Boot environment variable.
> tftpboot 0x81000000 <your image>-factory.img
> nand erase 0x1000000
> nand write 0x81000000 0x1000000 ${filesize}
> setenv bootpart 2
> saveenv
Revert to stock firmware
--------------
1. Revert to stock U-Boot environment variable.
> setenv bootpart 1
> saveenv
MAC addresses as verified by OEM firmware
--------------
WAN: *:XX (label)
LAN: *:XX + 1
2.4G: *:XX + 3
5G: *:XX + 4
The label MAC address was found in art 0x0.
Credits
--------------
Credit goes to the @manatails who first developed how to port OpenWRT
to this device and had a significant impact on this patch.
And thanks to @adschm and @mans0n for guiding me to revise the code
in many ways.
Signed-off-by: Jihoon Han <rapid_renard@renard.ga>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Sungbo Eo <mans0n@gorani.run>
This commit adds support for Xiaomi MiWiFi 3C device.
Xiaomi MiWifi 3C has almost the same system architecture
as the Xiaomi Mi WiFi Nano, which is already officially
supported by OpenWrt.
The differences are:
- Numbers of antennas (4 instead of 2). The antenna management
is done via the µC. There is no configuration needed in the
software code.
- LAN port assignments are different. LAN1 and WAN are
interchanged.
OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c
OpenWrt developers forum page:
https://forum.openwrt.org/t/support-for-xiaomi-mi-3c
Specifications:
- CPU: MediaTek MT7628AN (575MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LED: 1x amber/blue/red. Programmable
- Button: Reset
MAC addresses as verified by OEM firmware:
use address source
LAN *:92 factory 0x28
WAN *:92 factory 0x28
2g *:93 factory 0x4
OEM firmware uses VLAN's to create the network interface for WAN and LAN.
Bootloader info:
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader start OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".
How to install:
1- Use OpenWRTInvasion to gain telnet, ssh and ftp access.
https://github.com/acecilia/OpenWRTInvasion
(IP: 192.168.31.1 - Username: root - Password: root)
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0".
Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin
to /tmp in router using ftp.
5- Enable UART access and change start image for OS1.
```
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
```
6- Installing Openwrt on OS1 and free OS2.
```
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1
```
Limitations: For the first install the image size needs to be less
than 7733248 bits.
Thanks for all community and especially for this device:
minax007, earth08, S.Farid
Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com>
[wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to
&wmac, convert to nvmem]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* fix restart in LuCI (inherited umask was to restrictive)
* make directory of hosts-file (!= /tmp) accessible in ujail
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update VERSIONs to 3.3 for release.
Update VERSIONs to 3.3-rc3 for release.
Correct some typos
Update VERSIONs to 3.3-rc2 for release.
Update VERSIONs and Python bindings version to 3.3-rc1 for release
libsepol/secilc/docs: Update the CIL documentation
secilc: fix memory leaks in secilc2conf
secilc: fix memory leaks in secilc
libsepol/cil: Add support for using qualified names to secil2conf
libsepol/cil: Add support for using qualified names to secil2tree
secilc: Add support for using qualified names to secilc
secilc/test: Add test for anonymous args
secilc/docs: Relocate and reword macro call name resolution order
secilc/docs: Document the order that inherited rules are resolved in
secilc: Create the new program called secil2tree to write out CIL AST
secilc/docs: Update the CIL documentation for various blocks
secilc.c: Don't fail if input file is empty
cil_conditional_statements.md: fix expr definition
secilc/docs: Lists are now allowed in constraint expressions
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[re-apply now that libsepol is up-to-date as well]
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Update VERSIONs to 3.3 for release.
libsepol/cil: Fix potential undefined shifts
libsepol: Fix potential undefined shifts
Update VERSIONs to 3.3-rc3 for release.
libsepol/cil: Do not skip macros when resolving until later passes
libsepol/cil: Limit the amount of reporting for bounds failures
libsepol/cil: silence clang void-pointer-to-enum-cast warning
libsepol: resolve GCC warning about null-dereference
libsepol: use correct cast
libsepol: ebitmap: mark nodes of const ebitmaps const
Update VERSIONs to 3.3-rc2 for release.
libsepol/cil: Handle operations in a class mapping when verifying
libsepol/cil: Do not use original type and typeattribute datums
libsepol: free memory after policy validation
libsepol: avoid implicit conversions
libsepol: fix typo
libsepol/cil: Free duplicate datums in original calling function
libsepol/cil: Fix detected RESOURCE_LEAK (CWE-772)
Update VERSIONs and Python bindings version to 3.3-rc1 for release
libsepol/cil: Limit the number of active line marks
libsepol/cil: Add function to get number of items in a stack
libsepol: Fix detected RESOURCE_LEAKs
libsepol/cil: Fix syntax checking in __cil_verify_syntax()
libsepol/cil: Use size_t for len in __cil_verify_syntax()
libsepol/cil: Remove redundant syntax checking
libsepol/cil: Improve in-statement to allow use after inheritance
libsepol/cil: Simplify cil_tree_children_destroy()
libsepol/cil: Refactor the function __cil_build_ast_node_helper()
libsepol/cil: Don't destroy optionals whose parent will be destroyed
libsepol/cil: Properly check for parameter when inserting name
libsepol/cil: Reset expandtypeattribute rules when resetting AST
libsepol/cil: Properly check parse tree when printing error messages
libsepol/cil: Allow some duplicate macro and block declarations
libsepol/cil: When writing AST use line marks for src_info nodes
libsepol/cil: Report correct high-level language line numbers
libsepol/cil: Add line mark kind and line number to src info
libsepol/cil: Create common string-to-unsigned-integer functions
libsepol/cil: Push line mark state first when processing a line mark
libsepol/cil: Check for valid line mark type immediately
libsepol/cil: Check the token type after getting the next token
libsepol/cil: Check syntax of src_info statement
libsepol/cil: move the fuzz target and build script to the selinux repository
libsepol: replace strerror by %m
libsepol/cil: remove obsolete comment
libsepol/cil: do not allow \0 in quoted strings
libsepol/cil: Fix handling category sets in an expression
libsepol: assure string NUL-termination of ibdev_name
libsepol: avoid implicit conversions
libsepol: ignore UBSAN false-positives
libsepol: avoid unsigned integer overflow
libsepol/cil: Improve checking for bad inheritance patterns
libsepol: silence -Wextra-semi-stmt warning
libsepol/cil: do not override previous results of __cil_verify_classperms
libsepol/cil: Provide option to allow qualified names in declarations
libsepol/cil: make array cil_sym_sizes const
libsepol/cil: Only reset AST if optional has a declaration
libsepol/cil: Add function to determine if a subtree has a declaration
libsepol/cil: Improve degenerate inheritance check
libsepol/cil: Reduce the initial symtab sizes for blocks
libsepol/cil: Check for empty list when marking neverallow attributes
libsepol/cil: Fix syntax checking of defaultrange rule
libsepol/cil: Properly check for loops in sets
libsepol/cil: Allow duplicate optional blocks in most cases
libsepol: declare read-only arrays const
libsepol: declare file local variable static
libsepol: drop unnecessary casts
libsepol: drop repeated semicolons
libsepol/cil: avoid using maybe uninitialized variables
libsepol/cil: drop unnecessary casts
libsepol/cil: drop dead store
libsepol/cil: drop extra semicolon
libsepol/cil: silence cast warning
libsepol: remove dead stores
libsepol: do not allocate memory of size 0
libsepol: mark read-only parameters of type_set_ interfaces const
libsepol: mark read-only parameters of ebitmap interfaces const
libsepol: remove dead stores
libsepol/cil: follow declaration-after-statement
libsepol: follow declaration-after-statement
libsepol: avoid unsigned integer overflow
libsepol: remove unused functions
libsepol: resolve missing prototypes
libsepol: fix typos
libsepol: Quote paths when generating policy.conf from binary policy
libsepol/cil: Account for anonymous category sets in an expression
libsepol/cil: Fix anonymous IP address call arguments
libsepol: quote paths in CIL conversion
libsepol/cil: Resolve anonymous levels only once
libsepol/cil: Pointers to datums should be set to NULL when resetting
libsepol/cil: Resolve anonymous class permission sets only once
libsepol/cil: Limit the number of open parenthesis allowed
libsepol/cil: Destroy the permission nodes when exiting with an error
libsepol/cil: Handle disabled optional blocks in earlier passes
libsepol/cil: Do not resolve arguments to declarations in the call
libsepo/cil: Refactor macro call resolution
libsepol/cil: Do not add NULL node when inserting key into symtab
libsepol/cil: Make name resolution in macros work as documented
libsepol/cil: Fix name resolution involving inherited blocks
libsepol/cil: Check for self-referential loops in sets
libsepol/cil: Return an error if a call argument fails to resolve
libsepol/cil: Check datum in ordered list for expected flavor
libsepol/cil: Detect degenerate inheritance and exit with an error
libsepol/cil: Fix instances where an error returns SEPOL_OK
libsepol/cil: Properly reset an anonymous classperm set
libsepol: use checked arithmetic builtin to perform safe addition
libsepol/cil: Add functions to make use of cil_write_ast()
libsepol/cil: Create functions to write the CIL AST
libsepol/cil: Use CIL_ERR for error messages in cil_compile()
libsepol/cil: Make invalid statement error messages consistent
libsepol/cil: Do not allow tunable declarations in in-statements
libsepol/cil: Sync checks for invalid rules in macros
libsepol/cil: Check for statements not allowed in optional blocks
libsepol/cil: Sync checks for invalid rules in booleanifs
libsepol/cil: Reorder checks for invalid rules when resolving AST
libsepol/cil: Use AST to track blocks and optionals when resolving
libsepol/cil: Create new first child helper function for building AST
libsepol/cil: Cleanup build AST helper functions
libsepol/cil: Reorder checks for invalid rules when building AST
libsepol/cil: Move check for the shadowing of macro parameters
libsepol/cil: Create function cil_add_decl_to_symtab() and refactor
libsepol/cil: Refactor helper function for cil_gen_node()
libsepol/cil: Allow permission expressions when using map classes
libsepol/cil: Exit with an error if declaration name is a reserved word
libsepol/cil: More strict verification of constraint leaf expressions
libsepol/cil: Set class field to NULL when resetting struct cil_classperms
libsepol/cil: cil_reset_classperms_set() should not reset classpermission
libsepol/cil: Destroy classperm list when resetting map perms
libsepol/cil: Destroy classperms list when resetting classpermission
libsepol/cil: Fix out-of-bound read of file context pattern ending with "\"
libsepol/cil: Check for duplicate blocks, optionals, and macros
libsepol: Write "NO_IDENTIFIER" for empty CIL constraint expression
libsepol: Enclose identifier lists in CIL constraint expressions
libsepol/cil: Allow lists in constraint expressions
libsepol: Enclose identifier lists in constraint expressions
libsepol: Write "NO_IDENTIFIER" for empty constraint expression
libsepol: make num_* unsigned int in module_to_cil
libsepol/cil: do not leak avrulex_ioctl_table memory when an error occurs
libsepol/cil: fix NULL pointer dereference in __cil_insert_name
libsepol/cil: replace printf with proper cil_tree_log
libsepol/cil: remove stray printf
libsepol/cil: make cil_post_fc_fill_data static
libsepol: Check kernel to CIL and Conf functions for supported versions
libsepol: Remove unnecessary copying of declarations from link.c
libsepol: Properly handle types associated to role attributes
libsepol: Expand role attributes in constraint expressions
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[re-apply now that buildbot phase1 has caught up]
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Backport upstream fix for module load regression caused by IRAM recovery.
Without this patch devices using mainline ath10k driver could lost wireless
function because ath10k module failed to load.
Signed-off-by: Zhijun You <hujy652@gmail.com>
Back in the day, the board-2.bin came with ath10k-firmware-qca4019.
This changed with
commit c3b2efaf24 ("linux-firmware: ath10k: add board firmware packages")
which placed the board-2.bin into a separate package: ath10k-board-qca4019.
This was great, because it addressed one of the caveat of the original
ipq-wifi package:
commit fa03d441e9 ("firmware: add custom IPQ wifi board definitions")
| 2. updating ath10k-firmware-qca4019 will also replace
| the board-2.bin. For this cases the user needs to
| manually reinstall the wifi-board package once the
| ath10k-firmware-qca4019 is updated.
This could be extended further so that ipq-wifi packages
no longer use "install-override" and the various QCA4019
variants list the ath10k-board-qca4019 as a CONFLICT
package.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
OpenWrt maintains two special out-of-tree DT properties:
"qca,disable-5ghz" and "qca,disable-2ghz". These are implemented
in a mac80211 ath9k patch "550-ath9k-disable-bands-via-dt.patch".
With the things being what they are, now might be a good
point to switch the devices to the generic and upstream
"ieee80211-freq-limit" property. This property is much
broader and works differently. Instead of disabling the
drivers logic which would add the affected band and
channels. It now disables all channels which are not
within the specified frequency range.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # HH5A
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* SSH agent forwarding might cause security issues, locally and on the jump
machine (https://defn.io/2019/04/12/ssh-forwarding/). So allow to
completely disabling it.
* separate options for client and server
* keep it enabled by default
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
This reverts commit 2da891e735.
secilc 3.3 requires libsepol to be version 3.3 as well and doesn't
build otherwise. Revert for now.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit de8a800ca9.
Host build uses host includes instead of staging/hostpkg.
This breaks the build in case of selinux host libs being older than
version 3.3. Revert for now until better fix is found.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
wifi: writes to terminal
hotplugcall and sqm read class sysfile symlinks
unbound and sqm related loose ends
support/example: policycoreutils host-compile is required
TODO: this was wrong and it is actually needed
linguist detectable does not work this way
linguist-detectable
updates README
adds workflows
adds a note about persistent /var option
project moved to https://github.com/DefenSec/selinux-policy
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Update VERSIONs to 3.3 for release.
Update VERSIONs to 3.3-rc3 for release.
Correct some typos
Update VERSIONs to 3.3-rc2 for release.
Update VERSIONs and Python bindings version to 3.3-rc1 for release
libsepol/secilc/docs: Update the CIL documentation
secilc: fix memory leaks in secilc2conf
secilc: fix memory leaks in secilc
libsepol/cil: Add support for using qualified names to secil2conf
libsepol/cil: Add support for using qualified names to secil2tree
secilc: Add support for using qualified names to secilc
secilc/test: Add test for anonymous args
secilc/docs: Relocate and reword macro call name resolution order
secilc/docs: Document the order that inherited rules are resolved in
secilc: Create the new program called secil2tree to write out CIL AST
secilc/docs: Update the CIL documentation for various blocks
secilc.c: Don't fail if input file is empty
cil_conditional_statements.md: fix expr definition
secilc/docs: Lists are now allowed in constraint expressions
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Update VERSIONs to 3.3 for release.
Update VERSIONs to 3.3-rc3 for release.
libselinux/semodule: Improve extracting message
Correct some typos
Update VERSIONs to 3.3-rc2 for release.
Update VERSIONs and Python bindings version to 3.3-rc1 for release
policycoreutils: free memory of allocated context in newrole
policycoreutils: free memory of allocated context in run_init
policycoreutils: free memory on lstat failure in sestatus
policycoreutils: silence -Wextra-semi-stmt warning
fixfiles: do not exclude /dev and /run in -C mode
policycoreutils/setfiles: do not create useless setfiles.8.man file
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Update VERSIONs to 3.3 for release.
checkpolicy: Fix potential undefined shifts
Update VERSIONs to 3.3-rc3 for release.
checkpolicy: delay down-cast to avoid align warning
checkpolicy: drop incorrect cast
checkpolicy: update documentation
checkpolicy: print reason of fopen failure
checkpolicy: policy_define: cleanup declarations
Update VERSIONs to 3.3-rc2 for release.
checkpolicy: free extended permission memory
checkpolicy: print warning on source line overflow
checkpolicy: error out on parsing too big integers
checkpolicy: avoid implicit conversion
checkpolicy: resolve dismod memory leaks
checkpolicy: add missing function declarations
checkpolicy: mark file local functions in policy_define static
checkpolicy: mark read-only parameters in module compiler const
checkpolicy: misc checkpolicy tweaks
checkpolicy: misc checkmodule tweaks
checkpolicy: enclose macro argument in parentheses
Update VERSIONs and Python bindings version to 3.3-rc1 for release
checkpolicy: mark read-only parameters in policy define const
checkpolicy/test: mark file local functions static
checkpolicy: parse_util drop unused declaration
checkpolicy: drop redundant cast to the same type
checkpolicy: avoid potential use of uninitialized variable
checkpolicy: check before potential NULL dereference
checkpolicy: remove dead assignments
checkpolicy: follow declaration-after-statement
checkpolicy: use correct format specifier for unsigned
checkpolicy: drop dead condition
checkpolicy: simplify assignment
checkpolicy: drop -pipe compile option
checkpolicy: pass CFLAGS at link stage
checkpolicy: silence -Wextra-semi-stmt warning
checkpolicy: Do not automatically upgrade when using "-b" flag
libsepol/checkpolicy: Set user roles using role value instead of dominance
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Update VERSIONs to 3.3 for release.
Update VERSIONs to 3.3-rc3 for release.
Update VERSIONs to 3.3-rc2 for release.
Update VERSIONs and Python bindings version to 3.3-rc1 for release
libsemanage: Fix USE_AFTER_FREE (CWE-672) in semanage_direct_write_langext()
libsemanage: silence -Wextra-semi-stmt warning
libsemanage: fix use-after-free in parse_module_store()
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Update VERSIONs to 3.3 for release.
libselinux: Fix potential undefined shifts
Update VERSIONs to 3.3-rc3 for release.
Update VERSIONs to 3.3-rc2 for release.
libselinux/utils: drop requirement to combine compiling and linking
Update VERSIONs and Python bindings version to 3.3-rc1 for release
Improve error message for label file validation
libselinux: replace strerror by %m
libselinux: silence -Wextra-semi-stmt warning
libselinux/utils/getseuser.c: fix build with gcc 4.8
selinux.8: document how mount flag nosuid affects SELinux
libselinux: fix typo
libselinux: improve getcon(3) man page
libselinux: selinux_status_open: return 1 in fallback mode
libselinux: do not use status page fallback mode internally
libselinux: make selinux_status_open(3) reentrant
libselinux: avc_destroy(3) closes status page
libselinux: label_file.c: fix indent
libselinux: regex: unify parameter names
libselinux: sidtab_sid_stats(): unify parameter name
libselinux: drop redundant casts to the same type
libselinux: label_db::db_init(): open file with CLOEXEC mode
libselinux: matchpathcon: free memory on realloc failure
libselinux: label_file::init(): do not pass NULL to strdup
libselinux: init_selinux_config(): free resources on error
libselinux: matchmediacon(): close file on error
libselinux: store_stem(): do not free possible non-heap object
libselinux: getdefaultcon: free memory on multiple same arguments
libselinux: setexecfilecon(): drop dead assignment
libselinux: label_media::init(): drop dead assignment
libselinux: label_x::init(): drop dead assignment
libselinux: context_new(): drop dead assignment
libselinux: exclude_non_seclabel_mounts(): drop unused variable
libselinux: getconlist: free memory on multiple level arguments
libselinux: selabel_get_digests_all_partial_matches: free memory after FTS_D block
libselinux: selinux_restorecon: mark local variable static
libselinux: avcstat: use standard length modifier for unsigned long long
libselinux: sefcontext_compile: mark local variable static
libselinux: Sha1Finalise(): do not discard const qualifier
libselinux: label_common(): do not discard const qualifier
libselinux: selinux_file_context_cmp(): do not discard const qualifier
libselinux: sidtab_hash(): do not discard const qualifier
libselinux: silence -Wstringop-overflow warning from gcc 10.3.1
libselinux: selinux_check_passwd_access_internal(): respect deny_unknown
libselinux: do not duplicate make target when going into subdirectory
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Update VERSIONs to 3.3 for release.
libsepol/cil: Fix potential undefined shifts
libsepol: Fix potential undefined shifts
Update VERSIONs to 3.3-rc3 for release.
libsepol/cil: Do not skip macros when resolving until later passes
libsepol/cil: Limit the amount of reporting for bounds failures
libsepol/cil: silence clang void-pointer-to-enum-cast warning
libsepol: resolve GCC warning about null-dereference
libsepol: use correct cast
libsepol: ebitmap: mark nodes of const ebitmaps const
Update VERSIONs to 3.3-rc2 for release.
libsepol/cil: Handle operations in a class mapping when verifying
libsepol/cil: Do not use original type and typeattribute datums
libsepol: free memory after policy validation
libsepol: avoid implicit conversions
libsepol: fix typo
libsepol/cil: Free duplicate datums in original calling function
libsepol/cil: Fix detected RESOURCE_LEAK (CWE-772)
Update VERSIONs and Python bindings version to 3.3-rc1 for release
libsepol/cil: Limit the number of active line marks
libsepol/cil: Add function to get number of items in a stack
libsepol: Fix detected RESOURCE_LEAKs
libsepol/cil: Fix syntax checking in __cil_verify_syntax()
libsepol/cil: Use size_t for len in __cil_verify_syntax()
libsepol/cil: Remove redundant syntax checking
libsepol/cil: Improve in-statement to allow use after inheritance
libsepol/cil: Simplify cil_tree_children_destroy()
libsepol/cil: Refactor the function __cil_build_ast_node_helper()
libsepol/cil: Don't destroy optionals whose parent will be destroyed
libsepol/cil: Properly check for parameter when inserting name
libsepol/cil: Reset expandtypeattribute rules when resetting AST
libsepol/cil: Properly check parse tree when printing error messages
libsepol/cil: Allow some duplicate macro and block declarations
libsepol/cil: When writing AST use line marks for src_info nodes
libsepol/cil: Report correct high-level language line numbers
libsepol/cil: Add line mark kind and line number to src info
libsepol/cil: Create common string-to-unsigned-integer functions
libsepol/cil: Push line mark state first when processing a line mark
libsepol/cil: Check for valid line mark type immediately
libsepol/cil: Check the token type after getting the next token
libsepol/cil: Check syntax of src_info statement
libsepol/cil: move the fuzz target and build script to the selinux repository
libsepol: replace strerror by %m
libsepol/cil: remove obsolete comment
libsepol/cil: do not allow \0 in quoted strings
libsepol/cil: Fix handling category sets in an expression
libsepol: assure string NUL-termination of ibdev_name
libsepol: avoid implicit conversions
libsepol: ignore UBSAN false-positives
libsepol: avoid unsigned integer overflow
libsepol/cil: Improve checking for bad inheritance patterns
libsepol: silence -Wextra-semi-stmt warning
libsepol/cil: do not override previous results of __cil_verify_classperms
libsepol/cil: Provide option to allow qualified names in declarations
libsepol/cil: make array cil_sym_sizes const
libsepol/cil: Only reset AST if optional has a declaration
libsepol/cil: Add function to determine if a subtree has a declaration
libsepol/cil: Improve degenerate inheritance check
libsepol/cil: Reduce the initial symtab sizes for blocks
libsepol/cil: Check for empty list when marking neverallow attributes
libsepol/cil: Fix syntax checking of defaultrange rule
libsepol/cil: Properly check for loops in sets
libsepol/cil: Allow duplicate optional blocks in most cases
libsepol: declare read-only arrays const
libsepol: declare file local variable static
libsepol: drop unnecessary casts
libsepol: drop repeated semicolons
libsepol/cil: avoid using maybe uninitialized variables
libsepol/cil: drop unnecessary casts
libsepol/cil: drop dead store
libsepol/cil: drop extra semicolon
libsepol/cil: silence cast warning
libsepol: remove dead stores
libsepol: do not allocate memory of size 0
libsepol: mark read-only parameters of type_set_ interfaces const
libsepol: mark read-only parameters of ebitmap interfaces const
libsepol: remove dead stores
libsepol/cil: follow declaration-after-statement
libsepol: follow declaration-after-statement
libsepol: avoid unsigned integer overflow
libsepol: remove unused functions
libsepol: resolve missing prototypes
libsepol: fix typos
libsepol: Quote paths when generating policy.conf from binary policy
libsepol/cil: Account for anonymous category sets in an expression
libsepol/cil: Fix anonymous IP address call arguments
libsepol: quote paths in CIL conversion
libsepol/cil: Resolve anonymous levels only once
libsepol/cil: Pointers to datums should be set to NULL when resetting
libsepol/cil: Resolve anonymous class permission sets only once
libsepol/cil: Limit the number of open parenthesis allowed
libsepol/cil: Destroy the permission nodes when exiting with an error
libsepol/cil: Handle disabled optional blocks in earlier passes
libsepol/cil: Do not resolve arguments to declarations in the call
libsepo/cil: Refactor macro call resolution
libsepol/cil: Do not add NULL node when inserting key into symtab
libsepol/cil: Make name resolution in macros work as documented
libsepol/cil: Fix name resolution involving inherited blocks
libsepol/cil: Check for self-referential loops in sets
libsepol/cil: Return an error if a call argument fails to resolve
libsepol/cil: Check datum in ordered list for expected flavor
libsepol/cil: Detect degenerate inheritance and exit with an error
libsepol/cil: Fix instances where an error returns SEPOL_OK
libsepol/cil: Properly reset an anonymous classperm set
libsepol: use checked arithmetic builtin to perform safe addition
libsepol/cil: Add functions to make use of cil_write_ast()
libsepol/cil: Create functions to write the CIL AST
libsepol/cil: Use CIL_ERR for error messages in cil_compile()
libsepol/cil: Make invalid statement error messages consistent
libsepol/cil: Do not allow tunable declarations in in-statements
libsepol/cil: Sync checks for invalid rules in macros
libsepol/cil: Check for statements not allowed in optional blocks
libsepol/cil: Sync checks for invalid rules in booleanifs
libsepol/cil: Reorder checks for invalid rules when resolving AST
libsepol/cil: Use AST to track blocks and optionals when resolving
libsepol/cil: Create new first child helper function for building AST
libsepol/cil: Cleanup build AST helper functions
libsepol/cil: Reorder checks for invalid rules when building AST
libsepol/cil: Move check for the shadowing of macro parameters
libsepol/cil: Create function cil_add_decl_to_symtab() and refactor
libsepol/cil: Refactor helper function for cil_gen_node()
libsepol/cil: Allow permission expressions when using map classes
libsepol/cil: Exit with an error if declaration name is a reserved word
libsepol/cil: More strict verification of constraint leaf expressions
libsepol/cil: Set class field to NULL when resetting struct cil_classperms
libsepol/cil: cil_reset_classperms_set() should not reset classpermission
libsepol/cil: Destroy classperm list when resetting map perms
libsepol/cil: Destroy classperms list when resetting classpermission
libsepol/cil: Fix out-of-bound read of file context pattern ending with "\"
libsepol/cil: Check for duplicate blocks, optionals, and macros
libsepol: Write "NO_IDENTIFIER" for empty CIL constraint expression
libsepol: Enclose identifier lists in CIL constraint expressions
libsepol/cil: Allow lists in constraint expressions
libsepol: Enclose identifier lists in constraint expressions
libsepol: Write "NO_IDENTIFIER" for empty constraint expression
libsepol: make num_* unsigned int in module_to_cil
libsepol/cil: do not leak avrulex_ioctl_table memory when an error occurs
libsepol/cil: fix NULL pointer dereference in __cil_insert_name
libsepol/cil: replace printf with proper cil_tree_log
libsepol/cil: remove stray printf
libsepol/cil: make cil_post_fc_fill_data static
libsepol: Check kernel to CIL and Conf functions for supported versions
libsepol: Remove unnecessary copying of declarations from link.c
libsepol: Properly handle types associated to role attributes
libsepol: Expand role attributes in constraint expressions
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Some packages may require additional group membership for the system
user added by that package. Allow defining additional groups as third
member of the ':'-separated tuple, allowing to specify multiple
','-separated groups with optional GID.
Example:
USERID:=foouser=1000:foogroup=1000:addg1=1001,addg2=1002,addg3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The 'madvise', syscall is missing.
Found with 'utrace /usr/sbin/umdns' on an R7800 and RT3200.
Signed-off-by: Michael Peleshenko <mpeleshenko@gmail.com>
Add support for SAM9X60-EK board.
Hardware:
- SoC: SAM9X60
- RAM: Winbond W972GG6KB-25 (2Gbit DDR2)
- NAND Flash: Micron MT29F4G08ABAEA
- QSPI Flash: Microchip SST26VF064B
- EEPROM: Microchip 24AA02E48
- SDMMC: One standard 4-bit SD card interface
- USB: two stacked Type-A connectors with power switches, one micro-B
USB device
- CAN: 2 interfaces (Microchip MCP2542)
- Ethernet: one 10/100Mbps
- WiFi/BT: one optional WiFi/Bluetooth interface
- Audio: one ClassD port
- Display: one 24-bit LCD interface
- Camera: one 12-bit image sensor interface
- IO: one IO expander (Microchip MCP23008)
- Debug ports: one J-Link-OB + CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: 4 push button switches
- Expansion: one PIO connector, one mikrobus connector
- Power management: two power regulators, two power consumption measurement
devices
Flashing:
- follow the procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sam9x60EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D27 WLSOM1-EK board.
Hardware:
- SIP: SAMA5D27C-LD2G-CU including SAMA5D27 MPU and 2Gbit LPDDR2-SDRAM
- MMC: one standard SD card interface
- Flash: 64 Mb serial quad I/O flash memory (SST26VF064BEUIT-104I/MF)
with embedded EUI-48 and EUI-64 MAC addresses
- USB: one USB device, one USB host one HSIC interface
- Ethernet: 1x10/100Mbps port
- WiFi/BT: IEEE 802.11 b/g/n Wi-Fi plus Bluetooth (Wi-Fi/BT) module
(ATWILC3000-MR110UA)
- Crypto: one ATECC608B-TNGTLS secure element
- Video: one LCD RGB 18-bit interface, one ISC 12-bit camera interface
- Debug port: one JTAG interface, one UART interface, one WILC UART
interface
- Leds: one RGB LED
- Buttons: start, reset, wakeup, user buttons
- Expansion: one tamper connector, one mikrobus interface, 2 XPRO PTC
connector
- Power managament: PMIC (MCP16502)
Flashing:
- follow procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d27WLSom1EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D2 ICP board.
Hardware:
- SoC: SAMA5D27
- RAM: 512 MB DDR3L
- MMC: One stanard SD card interface
- USB: One USB host switch 4 ports with power switch,
One USB device type Micro-AB
- CAN: 2 interfaces
- Ethernet: One Gigabit Ethernet PHY through HSIC,
One ETH switchport,
One EtherCAT interface
- WiFi/BT: Footprint for IEEE 802.11 b/g/n Wi-Fi plus
Bluetooth module (Wi-Fi/BT), suitable for
Microchip WILC3000-MR110CA or WILC3000-MR110UA
- Debug port: One J-Link-OB/J-Link-CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: reset, wakeup, 2 user buttons
- Expansion: one PIOBU/PIO connector, 3 mikrobus sockets
- Power mangament: PMIC (MCP16502), one power consumption device
(PAC1934)
Not working in Linux:
- EtherCAT interface: there is no Linux support integrated
- PAC1934: driver available at [1] but not integrated in Linux
Flashing:
- follow the procedure at [2]
[1] https://ww1.microchip.com/downloads/en/DeviceDoc/pac193x_linux_driver.zip
[2] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d2IcpMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
No package here depends on it. Furthermore, uClibc++ is a fairly buggy
C++ library and seems to be relatively inactive upstream.
It also lacks proper support for modern C++11 features.
The main benefit of it is size: 66.6 KB vs 287.3 KB on mips24kc. Static
linking and LTO can help bring the size down of packages that need it.
Added warning message to uclibc++.mk
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Host libraries are only build static, so let's pass --static to
pkg-config globally and remove the then unnecessary patches doing
exactly that individually.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Using Host/Exports doesn't work as intended, explicitly add the
required vars so that u-boot finds the required libraries when building
its tools.
Signed-off-by: Andre Heider <a.heider@gmail.com>
This function is missing in kernel 5.4, but it is sued by ath10k.
This fixes the build of ath10k on some targets.
Fixes: cfe0eb7485 ("mac80211: Update to version 5.14.13-1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The removed patches were applied upstream.
The Cisco Aironet 802.11b driver was removed from backports, remove
it also from OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The removed patches were applied upstream.
of_get_mac_address() was backported in our OpenWrt kernel, remove the
change from backports.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The removed patches were applied upstream.
This backports version 5.11.22 and later does not support kernel
versions < 4.4, this allows us to remove some patches too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
e983a25 Update regulatory rules for Ecuador (EC)
a0bcb88 wireless-regdb: Update regulatory rules for Norway (NO) on 6 and 60 GHz
cdf854d wireless-regdb: Update regulatory rules for Germany (DE) on 6GHz
86cba52 wireless-regdb: reduce bandwidth for 5730-5850 and 5850-5895 MHz in US
6fa2384 wireless-regdb: remove PTMP-ONLY from 5850-5895 MHz for US
9839e1e wireless-regdb: recent FCC report and order allows 5850-5895 immediately
42dfaf4 wireless-regdb: update 5725-5850 MHz rule for GB
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Per FHS 3.0, /var/lock is the location for lock files [1].
However its current permissions (755) are too restrictive
for use by unprivileged processes.
Debian and Ubuntu set them to 1777, and now so do we.
[1] <https://refspecs.linuxfoundation.org/FHS_3.0/fhs-3.0.html#varlockLockFiles>
Signed-off-by: Deomid Ryabkov <rojer@rojer.me>
[fixed typo in commit message, had to remove "rojer" due to git hooks]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This fixes passing a bogus non-null pointer to the ubus handler in case
the transition request is rejected.
Signed-off-by: David Bauer <mail@david-bauer.net>
Both hostapd and netifd attempt to add a VLAN device to a bridge.
Depending on which one wins the race, bridge vlan settings might be incomplete,
or hostapd might run into an error and refuse to service the client.
Fix this by preventing hostapd from adding interfaces to the bridge and
instead rely entirely on netifd handling this properly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
c61a1d432b34 wireless: fix creating AP mode WDS station interfaces
f78bdec2ed5f wireless: fix handling vif attributes on reload with mode change
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Refactor so that the outer function opens and closes the mei fd and
passes it around, just as with the main fd.
That also allows us to use the IOCTL macro in get_vector_status() and
clean up accordingly.
Switch to AUTORELEASE while at it.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Add in a fix for 160Mhz dfs on 5.10 and higher.
Add support for 5.13 and 5.15 kernels.
Add of_get_mac_address support for 5.15 driver.
Signed-off-by: Andrew Robbins <andrew@robbinsa.me>
The nl80211 was out of sync with the version used in our backports. This
broke the configuration of the antenna gain.
Fixes: 2bfac61483 ("mac80211: backport support for BSS color changes")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
They're preferred terminal descriptions for tmux, with additional support to
some special characters and italic fonts. More info can be found at:
https://github.com/tmux/tmux/wiki/FAQ
Fixes: FS#3404
Signed-off-by: Jitao Lu <dianlujitao@gmail.com>
When a ubus event handler denies a association with a non-zero return
value, the code jumps to preceeding code, creating an endless loop until
the event handler accepts the assc request.
Move the ubus handler further up the code to avoid creating such a loop.
Signed-off-by: David Bauer <mail@david-bauer.net>
Right now when I want to temporarily disable wg peer I need to delete
the entire peer section. This is not such a good solution because I
loose the previous configuration of the peer.
This patch adds `disabled` option to peer config which causes that
the config section is ignored.
Signed-off-by: Stepan Henek <stepan.henek@nic.cz>
[use $(AUTORELEASE)]
Signed-off-by: Paul Spooren <mail@aparcar.org>
