This adds clock drivers for the MediaTek MT7988 SoC
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This allows loading modules with large memory requirements, recently needed
while testing on armvirt/32. Past forum discussions [1] and bug reports [2]
also raised this and the ipq806x target already set it in response [3].
Given this increases kernel image size by only ~1KB, is generally useful on
multi-platform kernels, and enabled by default on upstream arm32 Linux, add
it to the generic config.
The setting has similar utility on arm64, is a requirement for KASLR, and
already enabled on most OpenWrt aarch64 targets, so pull this into the
top-level generic config.
[1]: https://forum.openwrt.org/t/vmap-allocation-for-size-442368-failed-use-vmalloc-size-to-increase-size/34545/7
[2]: https://github.com/openwrt/openwrt/issues/8282
[3]: f81e148eb6 ("ipq806x: update 4.19 kernel config").
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The identical change was previously added to the 5.15 kernel in the commit
9226f1e419 ("kernel: disable CONFIG_CPU_LITTLE_ENDIAN in generic config").
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Allow building SD card images without having both initramfs and squashfs
present on the card, just like it has already been done for the mt7622
and filogic subtargets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Refresh dts for kernel 6.1 support.
Changes:
- nbg6817 drop amba node and reference directly sdcc1.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
With 6.1 lots have changed and the platform for Makefile.boot got
dropped. Replace the patch with a new version that is alligned to the
new implementation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Update the WWAN kmods for compilation under kernel 6.1:
* Depend on kernel not being 5.10 rather than only 5.15
* Enable CONFIG_WWAN_DEBUGFS as its now optional from 5.17
* Add missing symbols for new WWAN drivers to generic config
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing symbol while adding layerscape support
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[ add commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
random_ether_addr is just a reference to eth_random_addr, that was later
dropped in more recent kernel version.
Drop random_ether_addr and use eth_random_addr directly to fix
compilation error in 6.1
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Instead of reference vlan and do strange subtraction, use the handy
struct_group() to create a virtual struct of the same size of the
members. This permits to have a more secure memset and fix compilation
warning in 6.1 where additional checks are done.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
With kernel 6.1 ieee2111_ptr is not compiled by default. Add pending
patch to restore this to make backports project compatible.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh mglru patch for new kernel version due to very fun backport
changing name from folio to pages.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh pending patches for kernel 6.1.
Changes:
- Refresh mtd patches with new implementation.
- Change 191-rtc-rs5c372-let_the_alarm_to_be_used_as_wakeup_source as
uie_unsupported got dropped and we now set the bit directly.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Zyxel EX5601-T0 specifics
--------------
The operator specific firmware running on the Zyxel branded
EX5601-T0 includes U-Boot modifications affecting the OpenWrt
installation.
Partition Table
| dev | size | erasesize | name |
| ---- | -------- | --------- | ------------- |
| mtd0 | 20000000 | 00040000 | "spi0.1" |
| mtd1 | 00100000 | 00040000 | "BL2" |
| mtd2 | 00080000 | 00040000 | "u-boot-env" |
| mtd3 | 00200000 | 00040000 | "Factory" |
| mtd4 | 001c0000 | 00040000 | "FIP" |
| mtd5 | 00040000 | 00040000 | "zloader" |
| mtd6 | 04000000 | 00040000 | "ubi" |
| mtd7 | 04000000 | 00040000 | "ubi2" |
| mtd8 | 15a80000 | 00040000 | "zyubi" |
The router boots BL2 which than loads FIP (u-boot).
U-boot has hardcoded a command to always launch Zloader "mtd read zloader 0x46000000" and than "bootm". Bootargs are deactivated.
Zloader is the zyxel booloader which allow to dual-boot ubi or ubi2, by default access to zloader is blocked.
Too zloader checks that the firmware contains a particolar file called zyfwinfo.
Additional details regarding Zloader can be found here:
https://hack-gpon.github.io/zyxel/https://forum.openwrt.org/t/adding-openwrt-support-for-zyxel-ex5601-t0/155914
Hardware
--------
SOC: MediaTek MT7986a
CPU: 4 core cortex-a53 (2000MHz)
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Micron xxx)
WIFI: Wifi6 Mediatek MT7976 802.11ax 5 GHz 4x4 + 2.4GHZ 4x4
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
1 x MaxLinear GPY211B 2.5 N-Base-T phy5 (lan4)
1 x MaxLinear GPY211B 2.5Gbit xor SFP/N-Base-T phy6 (wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
VOIP: 2 FXS ports for analog phones
MAC Address Table
-----------------
eth0/lan Factory 0x002a
eth1/wan Factory 0x0024
wifi 2.4Ghz Factory 0x0004
wifi 5Ghz Factory 0x0004 + 1
Serial console (UART)
---------------------
+-------+-------+-------+-------+-------+
| +3.3V | RX | TX | KEY | GND |
+---+---+-------+-------+-------+-------+
|
+--- Don't connect
Installation
------------
Keep in mind that openwrt can only run on the UBI partition, the openwrt firmware is not able to understand the zloader bootargs.
The procedure allows restoring the UBI partition with the Zyxel firmware and retains all the OEM functionalities.
1. Unlock Zloader (this will allow to swap manually between partitions UBI and UBI2):
- Attach a usb-ttl adapter to your computer and boot the router.
- While the router is booting at some point you will read the following: `Please press Enter to activate this console.`
- As soon as you read that press enter, type root and than press enter again (just do it, don't care about the logs scrolling).
- Most likely the router is still printing the boot log, leave it boot until it stops.
- If everything went ok you should have full root access "root@EX5601-T0:/#".
- Type the following command and press enter: "fw_setenv EngDebugFlag 0x1".
- Reboot the router.
- As soon as you read `Hit any key to stop autoboot:` press Enter.
- If everything went ok you should have the following prompt: "ZHAL>".
- You have successfully unlocked zloader access, this procedure must be done only once.
2. Check the current active partition:
- Boot the router and repeat the steps above to gain root access.
- Type the following command to check the current active image: "cat /proc/cmdline".
- If `rootubi=ubi` it means that the active partition is `mtd6`
- If `rootubi=ubi2` it means that the active partition is `mtd7`
- As mentioned earlier we need to flash openwrt into ubi/mtd6 and never overwrite ubi2/mtd7 to be able to fully roll-back.
- To activate and boot from mtd7 (ubi2) enter into ZHAL> command prompt and type the following commands:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- After rebooting check again with "cat /proc/cmdline" that you are correctly booting from mtd7/ubi2
- If yes proceed with the installation guide. If not probably you don't have a firmware into ubi2 or you did something wrong.
3. Flashing:
- Download the sysupgrade file for the router from openwrt, than we need to add the zyfwinfo file into the sysupgrade tar.
Zloader only checks for the magic (which is a fixed value 'EXYZ') and the crc of the file itself (256bytes).
I created a script to create a valid zyfwinfo file but you can use anything that does exactly the same:
https://raw.githubusercontent.com/pameruoso/OpenWRT-Zyxel-EX5601-T0/main/gen_zyfwinfo.sh
- Add the zyfwinfo file into the sysupgrade tar.
- Enter via telnet or ssh into the router with admin credentials
- Enter the following commands to disable the firmware and model checks
"zycli fwidcheck off" and "zycli modelcheck off"
- Open the router web interface and in the update firmware page select the "restore default settings option"
- Select the sysupgrade file and click on upload.
- The router will flash and reboot itself into openwrt from UBI
4. Restoring and going back to Zyxel firmware.
- Use the ZHAL> command line to manually swap the boot parition to UBI2 with the following:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- You will boot again the Zyxel firmware you have into UBI2 and you can flash the zyxel firmware to overwrite the UBI partition and openwrt.
Working features
----------------
3 gbit lan ports
Wifi
Zyxel partitioning for coexistance with Zloader and dual boot.
WAN SFP port (only after exporting pins 57 and 10. gpiobase411)
leds
reset button
serial interface
usb port
lan ethernet 2.5 gbit port (autosense)
wan ethernet 2.5 gbit port (autosense)
Not working
----------------
voip (missing drivers or proper zyxel platform software)
Swapping the wan ethernet/sfp xor port
----------------
The way to swap the wan port between sfp and ethernet is the following:
export the pins 57 and 10.
Pin 57 is used to probe if an sfp is present.
If pin 57 value is 0 it means that an sfp is present into the cage (cat /sys/class/gpio/gpio468/value).
If pin 57 value is 1 it means that no sfp is inserted into the cage.
In conclusion by default both 57 an 10 pins are by default 1, which means that the active port is the ethernet one.
After inserting an SFP pin 57 will become 0 and you have to manually change the value of pin 10 to 0 too.
This is totally scriptable of course.
Leds description
------------
All the leds are working out of the box but the leds managed by the 2 maxlinear phy (phy 5 lan, phy6 wan).
To activate the phy5 led (rj45 ethernet port led on the back of the router) you have to use mdio-tools.
To activate the phy6 led (led on the front of the router for 2.5gbit link) you have to use mdio-tools.
Example:
Set lan5 led to fast blink on 2500/1000, slow blink on 10/100:
mdio mdio-bus mmd 5:30 raw 0x0001 0x33FC
Set wan 2.5gbit led to constant on when wan is 2.5gbit:
mdio mdio-bus mmd 6:30 raw 0x0001 0x0080
Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
Specifications:
SOC: QCA9563 775 MHz + QCA9880
Switch: QCA8337N-AL3C
RAM: Winbond W9751G6KB-25 64 MiB
Flash: Winbond W25Q128FVSG 16 MiB
WLAN: Wi-Fi4 2.4 GHz 3*3 + 5 GHz 3*3
LAN: LAN ports *4
WAN: WAN port *1
Buttons: reset *1 + wps *1
LEDs: ethernet *5, power, wlan, wps
MAC Address:
use address source1 source2
label 40:9b:xx:xx:xx:3c lan && wlan u-boot,env@ethaddr
lan 40:9b:xx:xx:xx:3c devdata@0x3f $label
wan 40:9b:xx:xx:xx:3f devdata@0x8f $label + 3
wlan2g 40:9b:xx:xx:xx:3c devdata@0x5b $label
wlan5g 40:9b:xx:xx:xx:3e devdata@0x76 $label + 2
Install via Web UI:
Apply factory image in the stock firmware's Web UI.
Install via Emergency Room Mode:
DIR-859 A1 will enter recovery mode when the system fails to boot
or press reset button for about 10 seconds.
First, set computer IP to 192.168.0.5 and Gateway to 192.168.0.1.
Then we can open http://192.168.0.1 in the web browser to upload
OpenWrt factory image or stock firmware. Some modern browsers may
need to turn on compatibility mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
1. Remove unnecessary new lines in the dts.
2. Remove duplicate included file "gpio.h" in the device dts.
3. Add missing button labels "reset" and "wps".
4. Unify the format of the reg properties.
5. Add u-boot environment support.
6. Reduce spi clock frequency since the max value suggested by the
chip datasheet is only 25 MHz.
7. Add seama header fixup for DIR-859 A1. Without this header fixup,
u-boot checksum for kernel will fail after the first boot.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This patch enables NVMEM u-boot-env driver (COFNIG_NVMEM_U_BOOT_ENV) on
generic subtarget to use from devices, for MAC address and etc.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
read_page() need to return maximum number of bitflips instead of the
accumulated number. Change takes from upstream mt7621 u-boot [1].
* @read_page: function to read a page according to the ECC generator
* requirements; returns maximum number of bitflips
* corrected in any single ECC step, -EIO hw error
[1] https://lore.kernel.org/all/cover.1653015383.git.weijie.gao@mediatek.com/
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
the UML build fails during the kernel build:
| arch/um/drivers/net_kern.c: In function 'compute_hash':
| arch/um/drivers/net_kern.c:322:1: error: the frame size of 1072 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
| 322 | }
| | ^
|cc1: all warnings being treated as errors
The compute_hash() function is added by our patch:
102-pseudo-random-mac.patch
Instead of allocating a 1024 byte buffer on the stack for the SHA1
digest input, let's allocate the data on the heap. We should be
able to do that since crypto_alloc_ahash and ahash_request_alloc
also need to allocate structures on the heap.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The PHY name has been changed to "mt7530-0" since IRQ support
was added to MT7530 driver.
Fixes: f9cfe7af1f ("kernel: backport MT7530 IRQ support")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
(node names, added color, function+function-enumerator properties)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The Sophos SG/XG-135 revision 3 has odd numbering of eth ports
where the WAN port (as marked on the case) is:
`eth6` and `eth0`, `eth1`, `eth2`, `eth3`, `eth5`, `eth7`, `eth8` are LAN ports.
Port `eth4` seems to be the SFP port.
Also add the missing LED definition for supported Sophos devices.
Original discussion at:
https://forum.openwrt.org/t/openwrt-on-revision-3-of-sophos-desktop-appliances/152912
Signed-off-by: Stan Grishin <stangri@melmac.ca>
Iomega Storcenter ix4-200d is a four-bay SATA NAS powered by a Marvell
Kirkwood SoC clocked at 1.2GHz. It has 512MB of RAM and 32MB of
flash memory, 3x USB 2.0 and 2x 1Gbit/s NIC
Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1200Mhz
- Flash size: 32 MiB
- RAM: 512MB
- LAN: 2x 1Gbit/s
- 3x USB 2.0
Notes:
- The blue drive LED is triggered by HDD activity, it can not be controlled
via GPIO.
- The LCD screen requires proprietary code and does not function at this time.
- Due to a kernel-related issue with the Marvell 88SE6121 SATA controller,
currently only trays numbered #3 and #4 work, #1 and #2 do not. [1]
Serial pinout:
CN4
--------------
| 10 8 6 4 2 |
| 9 7 5 3 1 |
-------------- PIN 1 Mark (fat line)
1 = RXD
4 = TXD
6 = GND
9 = 3.3V (not necessary to connect)
Installation instructions:
1. download initramfs-uImage and copy into tftp server
2. connect the tftp server to network port #1
3. access uboot environment with serial cable and run
setenv mainlineLinux yes
setenv arcNumber 1682
setenv console 'console=ttyS0,115200n8'
setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
setenv bootargs_root 'root='
setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
saveenv
setenv serverip 192.168.1.1
setenv ipaddr 192.168.1.2
tftpboot 0x00800000 [initramfs-uImage filename]
bootm 0x00800000
4. connect to LAN on network port #2, log into openwrt and sysupgrade to install into flash
[1] https://bugzilla.kernel.org/show_bug.cgi?id=216094
Signed-off-by: Sander van Deijck <sander@vandeijck.com>
(aligned FROM from signed-off. LED+key rename, whitespace removal)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This removes unneeded kernel version switches from the targets after
kernel 5.10 has been dropped.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Recently, a strange variant of ZTE MF286 was discovered, having QCA9886
radio instead of QCA9882 - like MF286A, but having MF286 flash layout
and rest of hardware.
To support both variants in one image, bind calibration data at offset
0x5000 both as "calibration" and "pre-calibration" nvmem-cells, so
ath10k can load caldata for both at runtime.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Specifications
The D-Link EXO AC1750 (DIR-869) router released in 2016.
It is powered by Qualcomm Atheros QCA9563 @ 750 MHz chipset, 64 MB RAM and 16 MB flash.
10/100/1000 Gigabit Ethernet WAN port
Four 10/100/1000 Gigabit Ethernet LAN ports
Power Button, Reset Button, WPS Button, Mode Switch
Flashing
1. Upload factory.bin via D-link web interface (Management/Upgrade).
Revert to stock
Upload original firmware via OpenWrt sysupgrade interface.
Debricking
D-Link Recovery GUI (192.168.0.1)
Signed-off-by: Jan Forman <forman.jan96@gmail.com>
For D-link DIR-859 and DIR-869
Replace the mtd-cal-data by an nvmem-cell.
Add the PCIe node for the ath10k radio to the devicetree.
Thanks to DragonBlue for this patch
Signed-off-by: Jan Forman <jforman@tuta.io>
gpio-export for the switch reset pin replaced with a reset pin definition for the driver, within the phy node.
Signed-off-by: Jan Forman <forman.jan96@gmail.com>
Tested-By: Sebastian Schaper <openwrt@sebastianschaper.net>
The 'KERNEL' is not referenced by other objects, so double '$$' will
cause shell unable to parse the variable 'BLOCKSIZE':
dd ... bs=$(BLOCKSIZE) conv=sync
bash: line 1: BLOCKSIZE: command not found
Fixes: 09a0efbe83(ramips: set default BLOCKSIZE to 64k for nor flash devices)
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Replace the fall through comment with fallthrough; in the ar2315 flash
driver.
This fixes a compile warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of defining an own virt_to_phys() use the version from the
generic MIPS arch code which does the same.
This fixes a compile warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use same logic as in append-metadata so build doesn't fail in case of
missing build-key (it was previously failing on the buildbot runners).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kernel 5.15.111 includes backport of commit
("firmware: qcom_scm: Clear download bit during reboot") which is causing
reboot on ipq40xx to stop working, more precisely the board will hang after
reboot is called with:
root@OpenWrt:/# reboot
root@OpenWrt:/# [ 76.473541] device lan1 left promiscuous mode
[ 76.474204] br-lan: port 1(lan1) entered disabled state
[ 76.527975] device lan2 left promiscuous mode
[ 76.530301] br-lan: port 2(lan2) entered disabled state
[ 76.579376] device lan3 left promiscuous mode
[ 76.581698] br-lan: port 3(lan3) entered disabled state
[ 76.638434] device lan4 left promiscuous mode
[ 76.638777] br-lan: port 4(lan4) entered disabled state
[ 76.978489] qca8k-ipq4019 c000000.switch wan: Link is Down
[ 76.978883] device eth0 left promiscuous mode
[ 76.987077] ipqess-edma c080000.ethernet eth0: Link is Down
[
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00123
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Reset status Config, 0x00000010
S - Core 0 Frequency, 0 MHz
B - 261 - PBL, Start
B - 1339 - bootable_media_detect_entry, Start
B - 1679 - bootable_media_detect_success, Start
B - 1693 - elf_loader_entry, Start
B - 5076 - auth_hash_seg_entry, Start
B - 7223 - auth_hash_seg_exit, Start
B - 578349 - elf_segs_hash_verify_entry, Start
B - 696356 - PBL, End
B - 696380 - SBL1, Start
B - 787236 - pm_device_init, Start
D - 7 - pm_device_init, Delta
B - 788701 - boot_flash_init, Start
D - 52782 - boot_flash_init, Delta
B - 845625 - boot_config_data_table_init, Start
D - 3836 - boot_config_data_table_init, Delta - (419 Bytes)
B - 852841 - clock_init, Start
D - 7566 - clock_init, Delta
B - 864883 - CDT version:2,Platform ID:9,Major ID:0,Minor ID:0,Subtype:64
B - 868413 - sbl1_ddr_set_params, Start
B - 873402 - cpr_init, Start
D - 2 - cpr_init, Delta
B - 877842 - Pre_DDR_clock_init, Start
D - 4 - Pre_DDR_clock_init, Delta
D - 13234 - sbl1_ddr_set_params, Delta
B - 891155 - pm_driver_init, Start
D - 2 - pm_driver_init, Delta
B - 909105 - Image Load, Start
B - 1030210 - Boot error ocuured!. Error code: 303d
So, until a proper fix is found, lets revert the culprit patch to have
reboot working again.
Fixes: 228e0e1039 ("kernel: bump 5.15 to 5.15.111")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Manually adjusted before running quilt due to new location in tree:
backport-5.15/780-v5.16-bus-mhi-pci_generic-Introduce-Sierra-EM919X-support.patch
backport-5.15/781-v6.1-bus-mhi-host-always-print-detected-modem-name.patch
pending-5.15/790-bus-mhi-core-add-SBL-state-callback.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Signed-off-by: John Audia <therealgraysky@proton.me>
The NanoPi R2C is a minor variant of NanoPi R2S with the on-board NIC
chip changed from rtl8211e to yt8521s, and otherwise identical to R2S.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The bootscript for nanopi r2s/r4s only changes the serial address, so
make it auto detected in mmc bootscript rather than creating more
(redudant) files.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
should have been part of the ipq-wifi update.
Fixes: 8217f02a1c ("ipq-wifi: drop upstreamed board-2.bin")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add a ventana-img.gz compressed disk image to support
squashfs+ext4 on a block storage device such as USB/MMC/SATA.
The Ventana bootloader expects the bootscript to be
boot/6x_bootscript-ventana therefore we must create a bootfs
that matches this.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
These same codes are repeated for many devices now, it's better to
move them to shared definition. This commit also add the missing
KERNEL_SIZE of the ZyXEL NR7101 and ZyXEL LTE3301-PLUS.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
In kernel 5.15, the default erase sector size of the nor flash has
been switched from 4k to 64k. This may cause the configuration not
be preserved across upgrades. To avoid this issue, change the default
BLOCKSIZE to 64k.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Make use of minor sector size (4k) on supported flash chips to improve
spi read/write performance.
Tested on ramips/mt7628: Motorola MWR03
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The BDFs for the:
Aruba AP-365
Devolo Magic 2 WiFi next
Edgecore ECW5410
Edgecore OAP100
Extreme Networks WS-AP3915i
GL.iNet GL-A1300
GL.iNet GL-AP1300
GL.iNet GL-S1300
Linksys EA8300
Linksys WHW03v2
Nokia Wi4A AC400i
P&W R619AC
Pakedge WR-1
Qxwlan E2600AC C1
Sony NCP-HG100/Cellular
Teltonika RUTX10
ZTE MF18A
were upstreamed to the ath10k-firmware repository
and landed in linux-firmware.git.
Furthermore the BDFs for the:
8devices Habanero
8devices Jalapeno
Qxwlan E2600AC C2
have been updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Use <mdio>:<addr>:<speed> trigger instead of netdev(link) trigger for
Fortinet FortiGate 50E, to indicate link speed on the each phys.
1000 Mbps: Green
100 Mbps : Amber
10 Mbps : (turn off)
Fixes: 102dc5a625 ("mvebu: add support for Fortinet FortiGate 50E")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To use <mdio>:<addr>:<speed> trigger for LEDs, enable PHY LED trigger
(CONFIG_LED_TRIGGER_PHY).
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Enable BLK_DEV_SD and USB_STORAGE so that rootfs can be on a USB Mass
Storage device.
This increases the kernel Image by 66KiB
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable BLK_DEV_SD and USB_STORAGE so that rootfs can be on a USB Mass
Storage device.
This adds 23KiB to the compressed kernel size
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
support for MR18 and MR26 was developped before
the userspace nu801 was integrated with x86's
MX100 into OpenWrt. The initial nu801 + kmod-leds-uleds
caused build-bot errors.
The solution that worked for the MX100 was to include
the kmod-leds-uleds to the device platform module.
Thankfully, the MR26 and MR18 can just add the uleds
package to the DEVICE_PACKAGES variable.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Rename Newifi D2 to D-Team Newifi D2, and Newifi D1 to Lenovo Newifi D1.
Let's not make naming exceptions because of marketing whims.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
The TOZED ZLT S12 PRO is an AC1200 router featuring 4 Ethernet ports with a
TOZED TL70-C cellular modem which supports the NCM mode.
The stock firmware does SIM locking on the modem by stopping dialing when a
different PLMN is detected. This is not the case on OpenWrt.
Specifications:
- CPU: MediaTek MT7621AT
- RAM: 256MB DDR3
- NOR Flash: MX25L12833FM2I 16MB SPI Flash
- Wi-Fi 2.4Ghz: MT7603E
- Wi-Fi 5Ghz: MT7612E
- Switch: MT7530 4x 1Gbit Ports
- WWAN: Unisoc SL8563 based TOZED TL70-C LTE CAT6 cellular modem
- USB: 1x optional USB2.0 external port
- Switches/Buttons: WPS, Reset, Power Switch
- LEDs: Power, Wi-Fi, Data, Signal 1-5, Phone
Installation and TFTP Recovery:
- Connect to serial console.
- Boot initramfs image by choosing option 1 when U-Boot prompts.
- Install sysupgrade image via OpenWrt.
Serial Pins:
Located at the bottom right when looking from the front, right under the
Reset/WPS buttons. The pinout from the left is:
- RX
- GND
- TX
Baudrate is 115200.
When connecting from a powered off state, disconnect RX as it blocks the
boot process.
Link: http://www.sztozed.com/en/contents/58/84.html
Co-developed-by: Andre Cruz <me@1conan.com>
Signed-off-by: Andre Cruz <me@1conan.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
When adding support for the GL.iNet GL-MT3000 a reference to the
non-existent make_gl_metadata.py script was accidentally added.
Remove it, flashing from vendor firmware also works fine without that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
16MB SPI-NOR (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V
[LEDS] VCC-GND-RX-TX [ETH]
Header is located below the heatsink
Case
----
Unscrew the 4 bottom screws. Remove the top of the case by inserting a
small screwdriver into the ventilation holes and lift the top cover.
This works best by beginning near the ETH-ports. The top is clipped on
the front near the LEDs with two plastic clips. The back has a single
clip in the middle. Start at one of the back edges.
MAC-Addresses
-------------
80:AF:CA:00:F9:C6 LAN
80:AF:CA:00:F9:C7 WAN
80:AF:CA:00:F9:C6 W2
82:AF:CA:30:F9:C6 W5
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device. Keep pressing the "0" key to enter the U-Boot
shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.2. Rename the image to "cudy3000.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Note: Cudy does not yet provide a image for disabling their
signature-protection. This has happened in the past. Make sure to check
the wiki for a possible easier installation method.
Signed-off-by: David Bauer <mail@david-bauer.net>
Import patch to prevent crashes in case WO firmware is missing on devices
with only a single frontend (eg. MT7981+MT7976).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Following 5264296, Mirotik NAND devices now use yafut to flash the
kernel on devices. This method is incompatible with the old-style
"kernel2minor" flash mechanism.
Even though NAND images were disabled in default build since 21.02, a
user flashing a new-style image onto an old-style image would result in
in a soft-brick[1]. In order to prevent such accidental mishap,
especially as these device images will be reenabled in the upcoming
release, bump the compat version.
After the new image is flashed, the compat version can be updated:
uci set system.@system[0].compat_version='1.1'
uci commit
[1] https://github.com/openwrt/openwrt/pull/12225#issuecomment-1517529262
Cc: Michał Kępień <openwrt@kempniu.pl>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Refresh patches to make them cleanly apply.
This problem was found by the github CI.
Fixes: ecd9abc8c0 ("kernel: use upstream firmware patch for Broadcom's NVRAM")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It has just been queued for the v6.5. It allows Ethernet drivers to read
MACs from NVRAM using NVMEM interface.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The following adds the Aerohive BR200-WP router to OpenWrt under
the mpc85xx/p1010 subtarget.
Hardware:
- SoC: Freescale P1011
- NOR: Intel JS28F512M29EWH 64MB
- Memory: 2x Nanya NT5TU64M16GG-AC 128MB (Total of 256MB)
- 2.4GHz WiFi: Atheros AR9390-AL1A
- Eth1: Atheros AR8035-A PoE
- 2x LEDs
- 1x Button
- PoE PSE
Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a
password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, tftp boot the initramfs image:
dhcp; setenv serverip 192.168.1.3;
tftpboot 0x2004000 openwrt-mpc85xx-p1010-aerohive_br200-wp-initramfs-kernel.bin;
bootm 0x2004000;
3. Once booted, scp over the sysupgrade file and sysupgrade the device
to flash LEDE to the NOR.
Note:
MAC assigns are taken from stock firmware:
Name MAC addr Mode State Chan(Width) VLAN Radio Hive SSID
-------- -------------- -------- ----- ----------- ---- ---------- ---------- ---------
Mgt0 08ea:44XX:XXc0 - U - 1 - hive0 -
Eth0 08ea:44XX:XXc0 wan U - - - - -
Eth1 08ea:44XX:XXc2 access D - - - hive0 -
Eth2 08ea:44XX:XXc3 access D - - - hive0 -
Eth3 08ea:44XX:XXc4 access D - - - hive0 -
Eth4 08ea:44XX:XXc5 access D - - - hive0 -
Wifi0 08ea:44XX:XXd0 access U 1(20MHz) - radio_ng0 - -
Wifi0.1 08ea:44XX:XXd4 access D 1(20MHz) - radio_ng0 hive0 -
Note2:
PoE PSE could be managed with `realtek-poe` package. Example port
config:
config port
option enable '1'
option id '4'
option name 'lan2'
option poe_plus '0'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan1'
option poe_plus '0'
option priority '1'
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(switch@0 -> switch@10, Device's quickstart says LEDs are
amber and white => add function+color properties but keep
labels around, use pr_info)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
DTSes from of three boards was sent and accpeted upstream. Let's use
backport patches with small OpenWrt tweak like other upstream stuff.
List of boards:
- Zyxel NSA310S
- Endian 4i Edge 200
- Ctera C-200 V1
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Specifications:
SOC: Atheros/Qualcomm QCA9557-AT4A @ 720MHz
RAM: 2x Winbond W9751G6KB-25 (128 MiB)
FLASH: Hynix H27U1G8F2BTR-BC TSOP48 ONFI NAND (128 MiB)
WIFI1: Atheros AR9550 5.0GHz (SoC)
WIFI2: Atheros AR9582-AR1A 2.4GHz
WIFI2: Atheros AR9582-AR1A 2.4GHz + 5GHz
PHYETH: Atheros AR8035-A, 802.3af PoE capable Atheros (1x Gigabit LAN)
LED: 1x Power-LED, 1 x RGB Tricolor-LED
INPUT: One Reset Button
UART: JP1 on PCB (Labeled UART), 3.3v-Level, 115200n8
(VCC, RX, TX, GND - VCC is closest to the boot set jumper
under the console pins.)
Flashing instructions:
Depending on the installed firmware, there are vastly different
methods to flash a MR18. These have been documented on:
<https://openwrt.org/toh/meraki/mr18>
Tip:
Use an initramfs from a previous release and then use sysupgrade
to get to the later releases. This is because the initramfs can
no longer be built by the build-bots due to its size (>8 MiB).
Note on that:
Upgrades from AR71XX releases are possible, but they will
require the force sysupgrade option ( -F ).
Please backup your MR18's configuration before starting the
update. The reason here is that a lot of development happend
since AR71XX got removed, so I do advise to use the ( -n )
option for sysupgrade as well. This will cause the device
to drop the old AR71xx configuration and make a new
configurations from scratch.
Note on LEDs:
The LEDs has changed since AR71XX. The white LED is now used during
the boot and when upgrading instead of the green tricolor LED. The
technical reason is that currently the RGB-LED is brought up later
by a userspace daemon.
(added warning note about odm-caldata partition. remove initramfs -
it's too big to be built by the bots. MerakiNAND -> meraki-header.
sort nu801's targets)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This sort of reverts Koen Vandeputte's commit
6561ca1fa5 ("ath79: ar934x: fix mounting issues if subpage is not supported")
since it does not work on the MR18 as the UBI is coming from
Meraki in that way and it used to work with AR71XX before.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Two Mikrotik board families (SXT 5nD R2 and Routerboard 92x are using
software ECC on NAND. Some of them use chips capable of subpage write,
others do not - within the same family, and a common block size is
required for UBI, to avoid mounting errors. Set the ECC step size
explicitly for them to 2048B, so UBI can mount existing volumes without
problems, at the same time allowing to unlocking subpage write functionality,
reuqired for Meraki MR18.
Fixes: 6561ca1fa5 ("ath79: ar934x: fix mounting issues if subpage is not supported")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
specify that this functions adds a Cisco Meraki
special-sauce header for their custom loader/uboot.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
