The Kirkwood SoCs all have an onchip RTC that can hold the time
over e.g. a reboot which will help if no NTP servers are available.
Create a kernel module package for the Marvell RTC, and add it to
all Kirkwood devices that do not have their own discrete
battery-backed RTC. Adding it to platforms with a proper RTC
is just surplus.
All Kirkwoods have at least one RTC so add RTC to the features
list for Kirkwood as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add u-boot bootloader based on 2023.01 to support D1-based boards, currently:
- Dongshan Nezha STU
- LicheePi RV Dock
- MangoPi MQ-Pro
- Nezha D1
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
U-boot on D1 also uses OpenSBI as its payload. As the current version of
OpenSBI already supports D1 with no further patches required, allow
building it on the upcoming TARGET_d1 too.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Disabled services should be kept disabled after sysupgrade. This can be
easily handled using a proper uci-defaults script.
Extend sysupgrade to check for disabled services, generate uci-defaults
script disabling them and include it in backup.
Cc: Christian Marangi <ansuelsmth@gmail.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Replace mount + overlay with manually built tar archive that gets
prepended to the actual config files backup. This allows more
flexibility with including extra backup files. They can be included at
any paths and don't require writing to flash or mounting an overlay
which has its own limitations (mount points).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jo-Philipp Wich <jo@mein.io>
This allows building uncompressed tar archives from shell scripts (and
compressing them later if needed)
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
[rmilecki: adapt to sysupgrade needs]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It should be "BananaPi BPi-R3 Mini" instead of just "BananaPi BPi-R3".
Fixes: bc25519f98 ("uboot-mediatek: add builds for BananaPi BPi-R3 mini")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
this patch separates libe2p from e2fsprogs package, like all other
provided libraries are their own packages. Also some development headers
were missing so I added those along with pkg-config files.
Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
After commit ad62247800 ("base-files: improve lib/upgrade/common.sh")
behavior of export_bootdevice has been made consistent in such way that
always the whole disk device is exported (as that was the case already
when matching via UUID) rather than the partition device.
Do the same for the device holding the fitblk backing partition.
Fixes: 5992f976b3 ("base-files: recognize bootdevice on devices using fitblk")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Boards using the fitblk driver need special treatment when it comes to
detecting the actual block device used to store the image used to boot
from. Transparently handle this in 'export_bootdevice' and provide new
'fitblk_get_bootdev' function to replace implementations in
/lib/upgrade/platform.sh.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the new fitblk driver on the BananaPi R2 as well as UniElec U7623.
Introduce boot device selection for fitblk's /chosen/rootdisk
handle, similar to how it is already done on MT7622, MT7986 and MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The default environment for the Linksys E8450 and Belkin RT3200 got
truncated by one line due to a broken patch. While the impact was
luckily only cosmetic, fix it so bootmenu title also shows U-Boot
version again.
Fixes: 6aec3c7b5b ("mediatek: mt7622: modernize Linksys E8450 / Belkin RT3200 UBI build")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
**Netgear LBR20** is a router with two gigabit ethernets , three wifi radios and integrated LTE cat.18 modem.
SoC Type: Qualcomm IPQ4019
RAM: 512 MiB
Flash: 256 MiB , SLC NAND, 2 Gbit (Macronix MX30LF2G18AC)
Bootloader: U-Boot
Modem: LTE CAT.18 Quectel EG-18EA , Max. 1.2Gbps downlink / 150Mbps uplink
WiFi class AC2200:
- radio0 : 5G on QCA9888 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps , 80MHz - limited for low channels
- radio1: 2,4G on IPQ4019 ,WiFi4- 802.11b/g/n MIMO2x2 300Mbps 40Mhz
- radio2: 5G on IPQ4019 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps ,80Mhz - limited for high channels (from 100 up to 165) . Becouse of DFS remember to set country before turning on.
Ethernet: 2x1GbE (WAN/LAN1, LAN2)
LEDs: section power : green and red , section on top (orbi) drived by TLC59208F: red, green ,blue and white
USB ports: No
Buttons: 2 Reset and SYNC(WPS)
Power: 12 VDC, 2,5 A
Connector type: Barrel
OpenWRT Installation
1. Simplest way is just do upgrade from webpage with *factory.img
2. You can also do it with standard tool for Netgear's debricking - NMPRFlash
3. Most advanced way is to open device , connect to UART console and :
- Prepare OpenWrt initramfs image in TFTP server root (server IP 192.168.1.10)
- Connect serial console (115200,8n1) to UART connector
- Connect TFTP server to RJ-45 port
- Stop in u-Boot and run u-Boot command:
> setenv serverip 192.168.1.10
> set fdt_high 0x85000000
> tftpboot 0x83000000 openwrt-ipq40xx-generic-netgear_lbr20-initramfs-zImage.itb
> bootm 0x83000000
- Login via ssh
- upload or download *sysupgrade.bin ( like wget ... or scp transfer)
- Install image via "sysupgrade -n" (like “sysupgrade -n /tmp/openwrt-ipq40xx-generic-netgear_lbr20-squashfs-sysupgrade.bin”)
Back to Stock
- Download firmware from official Netgear's webpage , it will be *.img file after decompressing.
- Use NMRPFlash tool ( detailed insructions on project page https://github.com/jclehner/nmrpflash )
Open the case
- Unscrew nuts and remove washers from antenna's conectors.
- There are two Torx T10 screws under the label next to antenna conectors. You have to unglue this label from left and right corner to get it
- Two parts of shell covers will slide out from eachother , you have to unglue two small rubber pads and namplate sticker on bottom to do that.
- PCB is screwed with 4Pcs of Torx T10 screws
- Before lifting up PCB remove pigtiles for LTE antennas and release them from PCB and radiator (black and white wires)
- On other side of PCB ,in left bottom corner there is already soldered with 4 pins UART connector for console. Counting from left it is +3,3V , TX , RX ,GND (reffer to this picture: https://i.ibb.co/Pmrf9KB/20240116-103524.jpg )
BDF's files are in firmware_qca-wireless https://github.com/openwrt/firmware_qca-wireless/ and in parallel sent to ath10k@lists.infradead.org.
Signed-off-by: Marcin Gajda <mgajda@o2.pl>
It seems that ipq-wifi bump included and incorrect PKG_MIRROR_HASH value,
so fix it by using:
make package/firmware/ipq-wifi/check FIXUP=1
Fixes: 70fd815e57 ("qualcommax: ipq807x: add support for Linksys MX5300")
Signed-off-by: Robert Marko <robimarko@gmail.com>
When both variants of ath10k drivers are selected, any driver that is
selected along is being built twice, one for each ath10k variant.
Avoid these redundant builds by introducing an optional second parameter
to config_package that lists the variants for which the package is to be
built.
If the symbol is to be set for all of the variants, $(ALL_VARIANTS) can
be used. This is the case for the mac80211 and cfg80211 modules. If
the parameter is empty, then the module will be selected and thus built
when the first variant is compiled.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Having different build directories is the default when the package
Makefile defines more than one variant.
Mac80211 overrides PKG_BUILD_DIR, not taking different variants in
consideration, which causes clobbering the directories when both
variants are built.
When compiled with AUTOREMOVE=y, the effect is that the package is
unnecessarily rebuilt when the package is compiled again.
Wihout AUTOREMOVE, the problem is worse: the second variant will not be
rebuilt, and you end up with the smallbuffers variant being a copy of
the regular one.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Usage of word "add" was somehow misleading in those functions:
1. They don't really add (as in: append) anything. Result files are
created from scratch.
2. It wasn't clear what adding files means. It could be understood as
adding actual files somewhere (to existing archive?).
Also the word "add" was also a bit ambiguous.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rename function to more accurate and self-explanatory name:
1. Use "archive" in name as this functions creates tar archive
2. Avoid "conffiles" as this function may archive more than that
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This reverts commit 4fa9aaf0be.
That seemed like a good idea allowing us to include any runtime
generated file in archive. Unfortuantely it broke backups with files
from mounted directories.
When mounting overlay with / as lowerdir its mounts don't propagete in
the mountpoint. That resulted in empty directories:
/tmp/overlay.XXXXXX/backup/tmp/
/tmp/overlay.XXXXXX/backup/var/
/tmp/overlay.XXXXXX/backup/dev/
/tmp/overlay.XXXXXX/backup/proc/
etc.
As some platforms / users try to backup files like /var/dhcp.leases or
/boot/cmdline.txt it means we can't use that solution.
Link: http://lists.openwrt.org/pipermail/openwrt-devel/2024-February/042320.html
Link: https://lore.kernel.org/linux-fsdevel/67bb0571-a6e0-44ea-9ab6-91c267d0642f@gmail.com/T/#u
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This reverts commit bf304d10e9.
That uci-defaults script worked great but generating it required
mounting root dir as overlay lowerdir that needs to be reverted.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
With mac80211_hwsim I have seen such entries in OpenWrt 22.03:
HE Iftypes: managed, AP
The mac80211.sh script did not detect the entry and failed. Allow
arbitrary other entries before to fix this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In some situations (slow protocol or interfaces with auto 0), the
interfaces are not available during the dnsmasq initialization and
hence, the ignore setting will be skipped.
Install an interface trigger for ignored interfaces in case their
ifname cannot be resolved.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
[bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When QCA8072 is used in PSGMII mode with IPQ6018, PCS used for second
PHY port would overlap with one used by SGMII+ port. SoC has register
to select different PCS in such case.
Original code used PHY_ID for this decision, which also had other
issues, but is no longer viable since we moved to upstream QCA807x
driver.
Introduce DT property port3_pcs_channel to allow describing this in DT.
Default value is <2>, and for some QCA8072 designs <4> would be needed.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Currently there are no atf/tpl blobs for rk3566 SoCs
so this commit adds the prebuilt firmware from the vendor.
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
FriendlyElec renamed the NanoPi R4S board with EEPROM (mac address)
to "enterprise" edition, and it was added as a "new" board in upstream
kernel.
This patch switched to use that upstreamed dts and removed local
EEPROM patch.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Disabled services should be kept disabled after sysupgrade. This can be
easily handled using a proper uci-defaults script.
Extend sysupgrade to check for disabled services, generate uci-defaults
script disabling them and include it in backup.
Cc: Christian Marangi <ansuelsmth@gmail.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jo-Philipp Wich <jo@mein.io>
