The HooToo HT-TM05 is a battery powered router, with an Ethernet and USB port.
Vendor U-Boot limited to 1.5 MB kernel size, so use lzma loader (loader-okli).
Specifications:
SOC: MediaTek MT7620N
BATTERY: 10400mAh
WLAN: 802.11bgn
LAN: 1x 10/100 Mbps Ethernet
USB: 1x USB 2.0 (Type-A)
RAM: 64 MB
FLASH: GigaDevice GD25Q64, Serial 8 MB Flash, clocked at 50 MHz
Flash itself specified to 80 MHz, but speed limited by mt7620 SPI
fast-read enabled (m25p)
LED: Status LED (blue after boot, green with WiFi traffic
4 leds to indicate power level of the battery (unable to control)
INPUT: Power, reset button
MAC assignment based on vendor firmware:
2.4 GHz *:b4 (factory 0x04)
LAN/label *:b4 (factory 0x28)
WAN *:b5 (factory 0x2e)
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- Installation from TFTP (recovery)
- OpenWRT sysupgrade (Preserving and non-preserving), through the usual
ways: command line and LuCI
- LEDs (except as noted above)
- Button (reset)
- I2C, which is needed for reading battery charge status and level
- U-Boot environment / variables (from U-Boot, and OpenWrt)
Installation:
- Download the needed OpenWrt install files, place them in the root
of a clean TFTP server running on your computer. Rename the files as,
- ramips-mt7620-hootoo_tm05-squashfs-kernel.bin => kernel
- ramips-mt7620-hootoo_tm05-squashfs-rootfs.bin => rootfs
- Plug the router into your computer via Ethernet
- Set your computer to use 10.10.10.254 as its IP address
- With your router shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The router (10.10.10.128) will look for your computer at 10.10.10.254
and install the two files. Once it has finished installation, it will
automatically reboot and start up OpenWrt.
- Set your computer to use DHCP for its IP address
Notes:
- U-Boot environment can be modified, u-boot-env is preserved on initial
install or sysupgrade
- mtd-concat functionality is included, to leave a "hole" for u-boot-env,
combining the OEM kernel and rootfs partitions
I would like to thank @mpratt14 and @xabolcs for their help getting the
lzma loader to work!
Signed-off-by: Russell Morris <rmorris@rkmorris.us>
[drop changes in image/Makefile, fix indent and PKG_RELEASE in
uboot-envtools, fix LOADER_FLASH_OFFS, minor commit message facelift,
add COMPILE to Device/Default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
FCC ID: U2M-ENH200
Engenius ENH202 is an outdoor wireless access point with 2 10/100 ports,
built-in ethernet switch, internal antenna plates and proprietery PoE.
Specification:
- Qualcomm/Atheros AR7240 rev 2
- 40 MHz reference clock
- 8 MB FLASH ST25P64V6P (aka ST M25P64)
- 32 MB RAM
- UART at J3 (populated)
- 2x 10/100 Mbps Ethernet (built-in switch at gmac1)
- 2.4 GHz, 2x2, 29dBm (Atheros AR9280 rev 2)
- internal antenna plates (10 dbi, semi-directional)
- 5 LEDs, 1 button (LAN, WAN, RSSI) (Reset)
Known Issues:
- Sysupgrade from ar71xx no longer possible
- Power LED not controllable, or unknown gpio
MAC addresses:
eth0/eth1 *:11 art 0x0/0x6
wlan *:10 art 0x120c
The device label lists both addresses, WLAN MAC and ETH MAC,
in that order.
Since 0x0 and 0x6 have the same content, it cannot be
determined which is eth0 and eth1, so we chose 0x0 for both.
Installation:
2 ways to flash factory.bin from OEM:
- Connect ethernet directly to board (the non POE port)
this is LAN for all images
- if you get Failsafe Mode from failed flash:
only use it to flash Original firmware from Engenius
or risk kernel loop or halt which requires serial cable
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
In upper right select Reset
"Restore to factory default settings"
Wait for reboot and login again
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt boot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9f670000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
Return to OEM:
If you have a serial cable, see Serial Failsafe instructions
*DISCLAIMER*
The Failsafe image is unique to Engenius boards.
If the failsafe image is missing or damaged this will not work
DO NOT downgrade to ar71xx this way, can cause kernel loop or halt
The easiest way to return to the OEM software is the Failsafe image
If you dont have a serial cable, you can ssh into openwrt and run
`mtd -r erase fakeroot`
Wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
Format of OEM firmware image:
The OEM software of ENH202 is a heavily modified version
of Openwrt Kamikaze bleeding-edge. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-senao-enh202-uImage-lzma.bin
openwrt-senao-enh202-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring, and by swapping headers to see
what the OEM upgrade utility accepts and rejects.
OKLI kernel loader is required because the OEM firmware
expects the kernel to be no greater than 1024k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on built-in switch:
ENH202 is originally configured to be an access point,
but with two ethernet ports, both WAN and LAN is possible.
the POE port is gmac0 which is preferred to be
the port for WAN because it gives link status
where swconfig does not.
Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[assign label_mac in 02_network, use ucidef_set_interface_wan,
use common device definition, some reordering]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Engenius ENS202EXT v1 is an outdoor wireless access point with 2 10/100 ports,
with built-in ethernet switch, detachable antennas and proprietery PoE.
FCC ID: A8J-ENS202
Specification:
- Qualcomm/Atheros AR9341 v1
- 535/400/200/40 MHz (CPU/DDR/AHB/REF)
- 64 MB of RAM
- 16 MB of FLASH MX25L12835F(MI-10G)
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet (built-in switch Atheros AR8229)
- 2.4 GHz, up to 27dBm (Atheros AR9340)
- 2x external, detachable antennas
- 7x LED (5 programmable in ath79), 1x GPIO button (Reset)
Known Issues:
- Sysupgrade from ar71xx no longer possible
- Ethernet LEDs stay on solid when connected, not programmable
MAC addresses:
eth0/eth1 *:7b art 0x0/0x6
wlan *:7a art 0x1002
The device label lists both addresses, WLAN MAC and ETH MAC,
in that order.
Since 0x0 and 0x6 have the same content, it cannot be
determined which is eth0 and eth1, so we chose 0x0 for both.
Installation:
2 ways to flash factory.bin from OEM:
- Connect ethernet directly to board (the non POE port)
this is LAN for all images
- if you get Failsafe Mode from failed flash:
only use it to flash Original firmware from Engenius
or risk kernel loop which requires serial cable
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
In upper right select Reset
"Restore to factory default settings"
Wait for reboot and login again
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt boot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fdf0000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
*If you are unable to get network/LuCI after flashing*
You must perform another factory reset:
After waiting 3 minutes or when Power LED stop blinking:
Hold Reset button for 15 seconds while powered on
or until Power LED blinks very fast
release and wait 2 minutes
Return to OEM:
If you have a serial cable, see Serial Failsafe instructions
*DISCLAIMER*
The Failsafe image is unique to this model.
The following directions are unique to this model.
DO NOT downgrade to ar71xx this way, can cause kernel loop
The easiest way to return to the OEM software is the Failsafe image
If you dont have a serial cable, you can ssh into openwrt and run
`mtd -r erase fakeroot`
Wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
TFTP Recovery:
For some reason, TFTP is not reliable on this board.
Takes many attempts, many timeouts before it fully transfers.
Starting with an initramfs.bin:
Connect to ethernet
set IP address and TFTP server to 192.168.1.101
set up infinite ping to 192.168.1.1
rename the initramfs.bin to "vmlinux-art-ramdisk" and host on TFTP server
disconnect power to the board
hold reset button while powering on board for 8 seconds
Wait a minute, power LED should blink eventually if successful
and a minute after that the pings should get replies
You have now loaded a temporary Openwrt with default settings temporarily.
You can use that image to sysupgrade another image to overwrite flash.
Format of OEM firmware image:
The OEM software of ENS202EXT is a heavily modified version
of Openwrt Kamikaze bleeding-edge. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
openwrt-senao-ens202ext-uImage-lzma.bin
openwrt-senao-ens202ext-root.squashfs
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring, and by swapping headers to see
what the OEM upgrade utility accepts and rejects.
Note on the factory.bin:
The newest kernel is too large to be in the kernel partition
the new ath79 kernel is beyond 1592k
Even ath79-tiny is 1580k
Checksum fails at boot because the bootloader (modified uboot)
expects kernel to be 1536k. If the kernel is larger, it gets
overwritten when rootfs is flashed, causing a broken image.
The mtdparts variable is part of the build and saving a new
uboot environment will not persist after flashing.
OEM version might interact with uboot or with the custom
OEM partition at 0x9f050000.
Failed checksums at boot cause failsafe image to launch,
allowing any image to be flashed again.
HOWEVER: one should not install older Openwrt from failsafe
because it can cause rootfs to be unmountable,
causing kernel loop after successful checksum.
The only way to rescue after that is with a serial cable.
For these reasons, a fake kernel (OKLI kernel loader)
and fake squashfs rootfs is implemented to take care of
the OEM firmware image verification and checksums at boot.
The OEM only verifies the checksum of the first image
of each partition respectively, which is the loader
and the fake squashfs. This completely frees
the "firmware" partition from all checks.
virtual_flash is implemented to make use of the wasted space.
this leaves only 2 erase blocks actually wasted.
The loader and fakeroot partitions must remain intact, otherwise
the next boot will fail, redirecting to the Failsafe image.
Because the partition table required is so different
than the OEM partition table and ar71xx partition table,
sysupgrades are not possible until one switches to ath79 kernel.
Note on sysupgrade.tgz:
To make things even more complicated, another change is needed to
fix an issue where network does not work after flashing from either
OEM software or Failsafe image, which implants the OEM (Openwrt Kamikaze)
configuration into the jffs2 /overlay when writing rootfs from factory.bin.
The upgrade script has this:
mtd -j "/tmp/_sys/sysupgrade.tgz" write "${rootfs}" "rootfs"
However, it also accepts scripts before and after:
before_local="/etc/before-upgradelocal.sh"
after_local="/etc/after-upgradelocal.sh"
before="before-upgrade.sh"
after="after-upgrade.sh"
Thus, we can solve the issue by making the .tgz an empty file
by making a before-upgrade.sh in the factory.bin
Note on built-in switch:
There is two ports on the board, POE through the power supply brick,
the other is on the board. For whatever reason, in the ar71xx target,
both ports were on the built-in switch on eth1. In order to make use
of a port for WAN or a different LAN, one has to set up VLANs.
In ath79, eth0 and eth1 is defined in the DTS so that the
built-in switch is seen as eth0, but only for 1 port
the other port is on eth1 without a built-in switch.
eth0: switch0
CPU is port 0
board port is port 1
eth1: POE port on the power brick
Since there is two physical ports,
it can be configured as a full router,
with LAN for both wired and wireless.
According to the Datasheet, the port that is not on the switch
is connected to gmac0. It is preferred that gmac0 is chosen as WAN
over a port on an internal switch, so that link status can pass
to the kernel immediately which is more important for WAN connections.
Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[apply sorting in 01_leds, make factory recipe more generic, create common
device node, move label-mac to 02_network, add MAC addresses to commit
message, remove kmod-leds-gpio, use gzip directly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target has been mostly replaced by ath79 and won't be included
in the upcoming release anymore. Finally put it to rest.
This also removes all references in packages, tools, etc. as well as
the uboot-ar71xx and vsc73x5-ucode packages.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This introduces the vendor_model scheme to this target in order to
harmonize device names within the target and with the rest of
OpenWrt. In addition, custom board names are dropped in favor
of the generic script which takes the compatible.
Use the SUPPORTED_DEVICES variable to store the compatible where it
deviates from the device name, so we can use it in build recipes.
While at it, harmonize a few indents as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ALLNET ALL-WAP02860AC is a dual-band wireless access point.
Specification
SoC: Qualcomm Atheros QCA9558
RAM: 128 MB DDR2
Flash: 16 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet: 1x 10/100/1000 Mbps AR8035-A, PoE capable (802.3at)
LEDS: 5x, which four are GPIO controlled
Buttons: 1x GPIO controlled
UART: 4 pin header near Mini PCIe card, starting count from white
triangle on PCB
1. VCC 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
MAC addresses
Calibration data does not contain valid MAC addresses.
The calculated MAC addresses are chosen in accordance with OEM firmware.
Because of:
a) constrained environment (SNMP) when connecting through Telnet
or SSH,
b) hard-coded kernel and rootfs sizes,
c) checksum verification of kerenel and rootfs images in bootloder,
creating factory image accepted by OEM web interface is difficult,
therefore, to install OpenWrt on this device UART connection is needed.
The teardown is simple, unscrew four screws to disassemble the casing,
plus two screws to separate mainboard from the casing.
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
Installation
1. Prepare TFTP server with OpenWrt initramfs-kernel image.
2. Connect to LAN port.
3. Connect to UART port.
4. Power on the device and when prompted to stop autoboot, hit any key.
5. Alter U-Boot environment with following commands:
setenv failsafe_boot bootm 0x9f0a0000
saveenv
6. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
'setenv' to do that, then run following commands:
tftpboot 0x81000000 <openwrt_initramfs-kernel_image_name>
bootm 0x81000000
7. Wait about 1 minute for OpenWrt to boot.
8. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade -n /tmp/<openwrt_sysupgrade_image_name>
9. After flashing, the access point will reboot to OpenWrt. Wait few
minutes, until the Power LED stops blinking, then it's ready for
configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[add MAC address comment to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Now that my patches have been merged into upstream U-Boot, resync the
cosmetic changes and the commit IDs from the final commits.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This adds support for ZyXEL NBG6616 uboot-env access
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[add "ar71xx" to commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the WNDR4300TN, marketed by Belgian ISP
Telenet. The hardware is the same as the WNDR4300 v1, without the
fifth ethernet port (WAN) and the USB port. The circuit board has
the traces, but the components are missing.
Specifications:
* SoC: Atheros AR9344
* RAM: 128 MB
* Flash: 128 MB NAND flash
* WiFi: Atheros AR9580 (5 GHz) and AR9344 (2.4 GHz)
* Ethernet: 4x 1000Base-T
* LED: Power, LAN, WiFi 2.4GHz, WiFi 5GHz, WPS
* UART: on board, to the right of the RF shield at the top of the board
Installation:
* Flashing through the OEM web interface:
+ Connect your computer to the router with an ethernet cable and browse
to http://192.168.0.51/
+ Log in with the default credentials are admin:password
+ Browse to Advanced > Administration > Firmware Upgrade in the Telenet
interface
+ Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img
+ Proceed with the firmware installation and give the device a few
minutes to finish and reboot.
* Flashing through TFTP:
+ Configure your wired client with a static IP in the 192.168.1.x range,
e.g. 192.168.1.10 and netmask 255.255.255.0.
+ Power off the router.
+ Press and hold the RESET button (the factory reset button on the bottom
of the device, with the gray circle around it, next to the Telenet logo)
and turn the router on while keeping the button pressed.
+ The power LED will start flashing orange. You can release the button
once it switches to flashing green.
+ Transfer the image over TFTP:
$ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img
Signed-off-by: Davy Hollevoet <github@natox.be>
[use DT label reference for adding LEDs in DTSI files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This replaces the internal device names "Audi" and "Viper" with the
real model names, which a user would look for. This makes the
Linksys devices on this target consistent with the names recently
changed for mvebu based on the same idea.
As a consequence, the "viper" device definition is split into two
separate definitions with the correct names for both real models.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Update the U-Boot to version v2020.07. Also replace the Makefile rewrite
with a proper patch, explaining why this hack is needed.
Run-tested: FriendlyARM NanoPi R2S
Signed-off-by: David Bauer <mail@david-bauer.net>
also install the firmware for all the supported boards
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[fix ATF blob path in uboot-rockchip]
Signed-off-by: David Bauer <mail@david-bauer.net>
In imx6, we currently use the model from DTS to derive a board name
manually in /lib/imx6.sh.
However, if we have individual DTS files anyway, we can exploit
generic 02_sysinfo and use the compatible as board name directly.
While at it, remove the wildcards from /lib/upgrade/platform.sh as
these might make code shorter, but are quite unpleasant when grepping
for a specific device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
OpenWrt lately has harmonized device (definition) names to the
pattern vendor_model to improve overall consistency, also with
other values like the DTS compatible.
This patch applies that scheme to the layerscape target.
Since this (intentionally) creates a bigger overlap between DTS names,
compatible, and device definition name, it also moves DEVICE_DTS and
SUPPORTED_DEVICES definitions to the Device/Default blocks.
Apart from that, it also modifies several packages to use consistent
naming in order to keep the $(1) file references working.
While at it, remove one layer of complexity for the setup in
tfa-layerscape package.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Ever since this package was introduced, the SDK for mt7629 failed to
build as it started failing on this package.
Fixed by porting Hauke's similar patch for uboot-sunxi to uboot-mediatek.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Specifications:
* SoC: MediaTek MT7621A (880 MHz 2c/4t)
* RAM: Nanya NT5CC128M16IP-DIT (256M DDR3-1600)
* Flash: Macronix MX30LF1G18AC-TI (128M NAND)
* Eth: MediaTek MT7621A (10/100/1000 Mbps x5)
* Radio: MT7615N (2.4 GHz & 5 GHz)
4 antennae: 1 internal and 3 non-deatachable
* USB: 3.0 (x1)
* LEDs:
White (x1 logo)
Green (x6 eth + wps)
Orange (x5, hardware-bound)
* Buttons:
Reset (x1)
WPS (x1)
Everything works! Been running it for a couple weeks now and haven't had
any problems. Please let me know if you run into any.
Installation:
Flash factory image through GUI.
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
Signed-off-by: Santiago Rodriguez-Papa <contact@rodsan.dev>
[use v1 only, minor DTS adjustments, use LINKSYS_HWNAME and add it to
DEVICE_VARS, wrap DEVICE_PACKAGES, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add support for Marvell MACCHIATObin Single Shot, cortex-a72 based
Marvell ARMADA 8040 Community board. Single Shot was broken as the
device tree is different on the Double Shot Board.
Specifications:
- Quad core Cortex-A72 (up to 2GHz)
- DDR4 DIMM slot with optional ECC and single/dual chip select support
- Dual 10GbE (1/2.5/10GbE) SFP+
2.5GbE (1/2.5GbE) via SFP
1GbE via copper
- SPI Flash
- 3 X SATA 3.0 connectors
- MicroSD connector
- eMMC
- PCI x4 3.0 slot
- USB 2.0 Headers (Internal)
- USB 3.0 connector
- Console port (UART) over microUSB connector
- 20-pin Connector for CPU JTAG debugger
- 2 X UART Headers
- 12V input via DC Jack
- ATX type power connector
- Form Factor: Mini-ITX (170 mm x 170 mm)
More details at http://macchiatobin.net
Installation:
Write the Image to your Micro SD Card and insert it in the
MACCHIATObin Single Shot SD Card Slot.
In the U-Boot Environment:
1. reset U-Boot environment:
env default -a
saveenv
2. prepare U-Boot with boot script:
setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000"
saveenv
or manually (hanging lines indicate wrapped one-line command):
setenv fdt_name armada-8040-mcbin-singleshot.dtb
setenv image_name Image
setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr
$image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv
bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
$kernel_addr - $fdt_addr'
saveenv
On newer Bootloaders (18.12) the Variables have been changed, use:
setenv fdt_name armada-8040-mcbin-singleshot.dtb
setenv image_name Image
setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr_r
$image_name;ext4load mmc 1:1 $fdt_addr_r $fdt_name;setenv
bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
$kernel_addr_r - $fdt_addr_r'
Reported-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: Alexandra Alth <alexandra@alth.de>
[add specs and installation as provided by Alexandra Alth]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Between kernels 4.20 and 5.0, a new variant of this board has been
introduced ("Single Shot"), and the existing one has been renamed
with the appendix "Double Shot". [1]
This also adjusted the first compatible in the list:
marvell,armada8040-mcbin -> marvell,armada8040-mcbin-doubleshot
This patch updates the OpenWrt implementation of this device by
adjusting the relevant references to that compatible (i.e., our
board name).
To still provide support for 4.19 with our setup, this adds a
small patch to change the compatible there as well.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b1f0bbe2700051886b954192b6c1751233fe0f52
Cc: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
There had been an issue in Layerscape QSPI driver for very long
time, which made squashfs,jffs2 rootfs not work on QSPI NOR.
And the ubifs had been used as a workaround.
Now the issue has been fixed. So convert to use squashfs,jffs2
rootfs on QSPI NOR for Layerscape boards (LS1012ARDB/LS1046ARDB/
LS1088ARDB), and update u-boot bootargs for booting.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The block index of u-boot-env changed from mtd1 to mtd3 after upgrading kernel to 5.4.
This patch search the mtd block by label name, work as expect when perform a clean flash.
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
Arduino Yun is a microcontroller development board, based on Atmel
ATmega32u4 and Atheros AR9331.
Specifications:
- MCU: ATmega32U4
- SoC: AR9331
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: SoC internal
- Ethernet: 1x 10/100Mbps
- USB: 1x 2.0
- MicroSD: 1x SDHC
Notes:
- Stock firmware is based on OpenWrt AA.
- The SoC UART can be accessed only through the MCU.
YunSerialTerminal is recommended for access to serial console.
- Stock firmware uses non-standard 250000 baudrate by default.
- The MCU can be reprogrammed from the SoC with avrdude linuxgpio.
Installation:
1. Update U-Boot environment variables to adapt to new partition scheme.
> setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
> setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
> saveenv
2. Boot into stock firmware normally and perform sysupgrade with
sysupgrade image.
# sysupgrade -n -F /tmp/sysupgrade.bin
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Instead of building in a default environment which loads our environment
from the FAT partition.... just ask U-Boot to do it.
Submitted upstream at
https://patchwork.ozlabs.org/project/uboot/list/?series=184688
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
For building full SD/eMMC images for Banana Pi R2 we'll want a u-boot
image built for that platform.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Download the boot preloader code from the Banana Pi github repo and make
it available for bootable SD card image creation.
Supports only Banana Pi R2 for now.
Based on work by Alexey Loukianov <lx2@lexa2.ru> and others.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch adds support for the Linksys EA7500 V1 router.
Specification:
- CPU: Qualcomm IPQ8064
- RAM: 256MB
- Flash: NAND 128MB
- WiFi: QCA9982 an+ac + QCA9983 bgn
- Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337)
- USB: 1x USB 3.0 1x USB2.0
- Serial console: RJ-45 115200 8n1 (1V8 Voltage level)
- 2 Buttons
- 1 LED
Known issues:
- Some devices won't flash via web gui
Installation:
- Newer stock images doesn't allow to install custom firmware.
- Please downgrade software to 1.1.2 version. Official firmware:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img
- Do it two times to downgrade all stored images.
- Apply factory image via web-gui.
Serial + TFTP method:
- downgrade to 1.1.2 two times
- connect ehternet and serial cable
- set ip address of tftp server to 192.168.1.254
- put openwrt factory image to tftp folder and rename it to macan.bin
- stop device while booting in u-boot
- run command: "run flashimg"
- run command: "setenv boot_part 1"
- run command "saveenv"
- reset
Back to stock:
- Please use old non-gpg image like this 1.1.2:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img
- ssh to router and copy image to tmp
- use sysupgrade -n -F
Tested by github users: @jack338c and @grzesiczek1
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.
Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A
Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
# ubidetach -p /dev/mtd15
# ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
# fw_setenv bootcmd bootipq
8. Perform reboot.
Recover to stock firmware
-------------------------
1. Execute the following command.
# fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Zyxel NSA310S is a NAS based on Marvell kirkwood SoC.
Specification:
- Processor Marvell 88F6702 1 GHz
- 256MB RAM
- 128MB NAND
- 1x GBE LAN port (PHY: Marvell 88E1318)
- 2x USB 2.0
- 1x SATA
- 3x button
- 7x leds
- serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC)
Known issues:
- no kernel module for RTC. [*]
- buzzer (connected to MPP43) need to be drived by 1kHz signal
- no kernel module for internal MCU connected via I2C[**]
[*]
Karoly Pocsi made simple, unofficial driver for HT1382.
It can be found here:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/
[**]
Karoly Pocsi found how CPU talk with MCU:
It is possible to query the MCU-controlled fan speed and temperature:
i2cget -y 0x0 0x0a 0x07
i2cget -y 0x0 0x0a 0x08
The first value (0x07) is the temperature in ° C, the second (0x08) is
the time in milliseconds to complete one fan revolution (rpm = 60,000 / value).
Info translated from:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/
Installation:
TFTP:
1. Run serial console and go to u-boot.
2. Copy u-boot via tftp and write to NAND:
=> mw 0x0800000 0xffff 0x100000
=> nand erase 0x0 100000
=> setenv ipaddr 192.168.1.2
=> setenv serverip 192.168.1.4
=> tftp 0x0800000 nsa310s-u-boot.kwb
=> nand write 0x0800000 0x0 0x100000
=> reset
3. Run new u-Boot, repair bootcmd and restore MAC address from sticker
=> setenv ethaddr AA:BB:CC:DD:EE:FF
=> saveenv
4. Copy and run initramfs image
=> setenv ipaddr 192.168.1.2
=> setenv serverip 192.168.1.4
=> tftpboot zyxel_nsa310s-initramfs-uImage
=> bootm 0x800000
5. Download sysupgrade image and perform sysupgrade
USB:
1. Prepare usb fat32 drive with u-boot.kwb and initramfs image.
Stick it to USB 2.0 port.
2. Run serial console and go to u-boot.
3. Copy u-boot from usb and write to NAND:
=> mw 0x0800000 0xffff 0x100000
=> nand erase 0x0 100000
=> usb start
=> fatload usb 0 0x0800000 u-boot.kwb
=> nand write 0x0800000 0x0 0x100000
=> reset
4. Run new u-Boot, repair bootcmd and restore MAC address from sticker
=> setenv ethaddr AA:BB:CC:DD:EE:FF
=> saveenv
5. Copy and run initramfs image:
=> usb start
=> fatload usb 0 0x0800000 initramfs-uImage
=> bootm 0x800000
6. Download sysupgrade image and perform sysupgrade.
Based on work ThBexx <thomas.beckler@hotmail.com>
DTS based on dropped support in 0ebdf0c.
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[NSA310s -> NSA310S in DEVICE_MODEL]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many
characteristics (apart from its looks and the GPIO ports) with the 6-antenna
*white* "Xiaomi Redmi Router AC2100"
See the visual comparison of the two routers here:
https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg
Specification of R2100:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN in Yellow and Blue
- UART: On board (Don't know where is should be confirmed by anybody else)
- Modified u-boot
Hacking of official firmware process is same at both RM2100 and R2100.
Thanks to @namidairo
Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide
Guide is written for MacOS but it will work at linux.
needed packages: python3(with scapy), netcat, http server, telnet client
1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware
2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0
other than these I specified in here. Everything is same with:
f3792690c4
Thanks for all community and especially for this device:
@Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com)
MAC Locations:
WAN *:b5 = factory 0xe006
LAN *:b6 = factory 0xe000
WIFI 5ghz *:b8 = factory 0x8004
WIFI 2.4ghz *:b7 = factory 0x0004
Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com>
[refactored common image bits into Device/xiaomi-ac2100, fixed From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The RAVPower RP-WD009 is a batter-powered pocket sized router with SD
card lot and USB port.
Hardware
--------
CPU: MediaTek MT7628AN
RAM: 64M DDR2
FLASH: 16M GigaDevices SPI-NOR
WLAN: MediaTek MT7628AN 2T2R b/g/n
MediaTek MT7610E 1T1R n/ac
ETH: 1x FastEthernet
SD: SD Card slot
USB: USB 2.0
Custom PMIC on the I2C bus (address 0x0a).
Installation
------------
1. Press and hold down the reset button.
2. Power up the Device. Keep pressing the reset button for 10
more seconds until the Globe LED lights up.
3. Attach your Computer to the Ethernet port. Assign yourself the
address 10.10.10.1/24.
4. Access the recovery page at 10.10.10.128 and upload the OpenWrt
factory image.
5. The flashing will take around 1 minute. The device will reboot
automatically into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
This reverts commit 930f3c0148.
The build fails with the following build error:
arm-openwrt-linux-muslgnueabi-ld.bfd: drivers/built-in.o: in function `ide_init':
build_dir/target-arm_xscale_musl_eabi/u-boot-nsa310/u-boot-2020.04/drivers/block/ide.c:750: undefined reference to `ide_preinit'
make[4]: *** [Makefile:1700: u-boot] Error 1
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
the uboot of nsa310 cannot use the network chip
as it is a realtek on the PCIe lanes and not a
Marvell ethernet from the SoC.
Therefore tftp is not possible on this device
and the only way to install is by loading files
from a USB drive.
If the USB subsystem is dead there is no way to
install OpenWrt.
Enable sata support and commands so it can be
used as a fallback in case of USB issues.
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
The Netgear WNDRMAC v1 is a hardware variant of the Netgear WNDR3700 v2
Specifications
==============
* SoC: Atheros AR7161
* RAM: 64mb
* Flash on board: 16mb
* WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n)
* Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit)
* Power: 12 VDC, 2.5 A
* Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v1)
Flash Instructions
==================
It is possible to use the OEM Upgrade page to install the `factory`
variant of the firmware.
After the initial upgrade, you will need to telnet into the router
(default IP 192.168.1.1) to install anything. You may install LuCI
this way. At this point, you will have a web interface to configure
OpenWRT on the WNDRMAC v1.
Please use the `sysupgrade` variant for subsequent flashes.
Recovery Instructions
=====================
A TFTP-based recovery flash is possible if the need arises. Please refer
to the WNDR3700 page on openwrt.org for details.
https://openwrt.org/toh/netgear/wndr3700#troubleshooting_and_recovery
Signed-off-by: Renaud Lepage <root@cybikbase.com>
[update DTSI include name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Linksys devices in mvebu target feature a mixed naming,
where parts are based on the official product name (device
node, image; e.g. WRT3200ACM) and parts are based on the
internal code name (DTS file name, compatible, LED labels;
e.g. rango). This inconsistent naming has been perceived
as quite confusing.
A recent attempt by Paul Spooren to harmonize this naming
in kernel has been declined there. However, for us it still
makes sense to apply at least a part of these changes
locally.
Primarily, this patch changes the compatible in DTS and thus
the board name used in various scripts to have them in line
with the device, model and image names. Due to the recent
switch from swconfig to DSA, this allows us to drop
SUPPORTED_DEVICES and thus prevent seamless upgrade between
these incompatible setups.
However, this does not include the LED label rename from
Paul's initial patch: I don't think it's worth keeping the
enormous diff locally for this case, as we can implement
this much easier in 01_leds if we have to live with the
inconsistency anyway.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[rebase, extend to all devices, drop DT LED changes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
