This commits adds the "ramdisk" feature to ipq806x target. The
main driving force behind this decision is to facilitate the
installation of OpenWrt on some locked IPQ806x devices.
Examples:
- NEC Aterm WG2600HP
The U-Boot on WG2600HP is protected with a password which prevents
users from gaining access to the u-boot prompt in order to install
the images from there.
Therefore, on this device, installing OpenWrt by the user involves
changing the bootcmd as follows so that WG2600HP downloads and
executes initramfs image from TFTP server.
ex.:
bootcmd="ping ${serverip} && tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq"
- Buffalo WXR-2533DHP
The U-Boot on WXR-2533DHP has built-in firmware recovery mode.
It's activated by holding the "AOSS" button during boot. This
will trigger the device to download the firmware from an TFTP
server and booting from it. By using this, the user can the
install OpenWrt firmware without having access to the UART
console.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
Replace the code with a more readable version. Rename the recipe
to reflect the real usecase.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
The 'factory' partition will move to 0x50000-0x60000 in 2019. As
the webserver in bootloader is compatible with different mtdlayout,
all the users still can upgrade firmware whatever on ath79 or ar71xx.
Signed-off-by: Rosy Song <rosysong@rosinson.com>
This patch adds support for the COMFAST CF-E110N, an outdoor wireless
CPE with two Ethernet ports and a 802.11bgn radio.
Specifications:
- 650/400/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 26 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new want, so a factory reset will be
needed: once the new firmware is flashed, perform the factory reset by
pushing the reset button several times during the boot process, while the
WAN LED flashes, until it starts flashing quicker.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and keep it
pressed for >10 seconds. The recovery page will be at http://192.168.1.1
Notes:
The device is advertised, sold and labeled as "CF-E110N", but the
bootloader and the stock firmware identify it as "v2".
Acknowledgments:
Petr Štetiar <ynezz@true.cz>
Sebastian Kemper <sebastian_ml@gmx.net>
Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[drop unused labels from devicetree source file]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for TP-Link Archer C6 v2 (EU)
Hardware specification:
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q64CSIG (8MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: There's no UART header on the board
Flash instructions:
Upload
openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherC6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the reset
button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
According to the GPL source the non-EU variant has different
GPIOs assigned to some of the LEDs and buttons. The flash
layout might be different as well. The wikidevi entry for
Archer A6/C6 assumes they are identical.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
EnGenius EWS511AP is a wireless managed wall AP with PoE support,
based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887.
Short specification:
- 128MB of RAM
- 16 MB of SPI FLASH
- 2T2R 2.4 GHz (QCA9531), 802.11b/g/n
- 1T1R 5 GHz (QCA9887), 802.11ac/n/a
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED
- 1x RESET button
- built-in watchdog chipset
Flash instruction:
From EnGenius firmware to OpenWrt firmware:
Original firmware is based on QSDK.
Use sysupgrade firmware directly in vendor GUI.
Reset to factory default is necessary.
From OpenWrt firmware to EnGenius firmware:
1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
Put the OpenWrt firmware in the root directory on your computer.
2. Power up EWS511AP. Press 4 and then press any key to enter u-boot.
3. Download OpenWrt firmware
(ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin"
4. Flash the firmware
(ath)> erase 0x9f060000 +f50000
(ath)> cp.b $fileaddr 0x9f060000 $filesize
5. Reboot
(ath)> reset
Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
This device is called GL-AR300M, therefore rename the board(s)
to 'gl-ar300m-nor' and 'gl-ar300m-nand'
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[change boardname in uboot envtools as well, don't use wildcards for
boardname]
Signed-off-by: Mathias Kresin <dev@kresin.me>
CPU: Atheros AR9341 535MHz
RAM: 32MB
FLASH: 4MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9341 2x2:2 bgn
LED: Power (static on), LAN (controlled by Switch), WAN, SYS, WiFi, RFKill
BTN: WPS, WiFi, Reset
Installation:
Upload the factory image via the vendor-GUI.
Signed-off-by: Antonio Silverio <menion@gmail.com>
[resolve merge conflicts, squash commits, fix commit title, remove
default default off led properties, mark sysupgrade image compatible
with the ar71xx version of the board, drop blank lines from dts]
Signed-off-by: Mathias Kresin <dev@kresin.me>
With this commit the TP-Link Archer C58 and Archer C59 use caldata
patching in order to set the correct 5GHz MAC-address.
Tested on TP-Link Archer C59 v1.
For more details see commit 330965b.
Signed-off-by: David Bauer <mail@david-bauer.net>
Right now this patch adds nor image generation only. NAND image
generation is not supportet at the moment.
Furtheremore support for the MicroSD port is not implemented as of now.
Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x switch button, 1x reset button
- LED: 3x LEDS (green)
- Another LED can be accessed on GPIO 7 if soldered
Flash instruction:
- Set static ip to 192.168.1.2
- Unplug the power cord
- Hold reset button
- Plug power back in
- Right led will flash 5 times
- Release reset button
- Browse to 192.168.1.1
- Choose sysupgrade image in NOR-flash section
- Press "update nor firmware"
- After successful transfer unplug network cable before device restarts
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[resolve merge conflicts, rename buttons, use switch input type for mode
switch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The OCEDO Koala has incorrect PLL settings which result in ~3% packet
loss on ethernet connections.
Also omit the gmac-configuration as it's incorrect too.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware spec of DIR-859 A1:
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9880
USB is supported on the PCB but not connected.
Flash instructions:
1. Upgrade the factory.bin through the factory web interface or the u-boot
failsafe interface.
The firmware will boot up correctly for the first time.
Do not power off the device after OpenWrt has booted. Otherwise the u-boot
will enter failsafe mode as the checksum of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
After upgrading completes the u-boot won't complain about the firmware
checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin, just
upgrade the factory.bin through the u-boot failsafe interface and then goto
step 2.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
[squash commits, use common seama recipes, sync factory image recipe
with ramips version]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Create a common template which has the required image build code
defined. Add some new variables to pass individual parts to the seama
recipes.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The mask/shift computation used the pin group number instead of the pin
number, resulting in always modifying group 4 when applying muxes, so
fix it to consistently use the pin number.
Fixes: 0755c2d117 ("brcm63xx: add pinctrl support")
Reported-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix the switch port order to have the correct order in LuCI.
Fixes: FS#1469
Signed-off-by: Eduardo Barros <geadas@gmail.com>
[trim commit title, add a proper commit message, add fixes tag, keep
alphabetical order of the blocks]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specs
SoC: MT7621AT
RAM: 512MiB
Flash: 32MiB MX25L25635F SPI NOR
2.4G: MT7603EN
5G: MT7612EN
Ethernet: 4x GE ports (1x WAN, 3x LAN) with link status LEDs
USB 3.0
LEDs: POWER, 5G WIFI, 2.4G WIFI, USB, Internet.
The last two ones are controlled by GPIO
UART: There are 2 UARTs (UARTLITE1/ttyS0 and UARTLITE3/ttyS1) on board.
UARTLITE1 is close to LEDs, and UARTLITE3 is close to flash chip.
The stock u-boot uses UARTLITE1 by default. Baud rate is 57600
Flash instruction
1. telnet 192.168.9.1 2317, username is "root" and password is "admin"
One can alternatively use UART to log in
2. Put OpenWrt firmware in a FAT32 USB drive, and connect it to the router
One can alternatively download the firmware via wget through Internet
3. mtd write /path/to/openwrt.bin firmware
4. reboot
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Very similar to the DWR-921-C1, except has a telephony/RJ11 port (not
sure if supported, I didn't try), wireless router with QMI LTE embedded
modem is based on the MT7620N SoC.
Specification:
* MediaTek MT7620N (580 Mhz)
* 64 MB of RAM
* 16 MB of FLASH
* 802.11bgn radio
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* 2x external, detachable (LTE) antennas
* UART header on PCB (57600 8n1)
* 6x LED (GPIO-controlled)
* 1x bi-color Signal Strength LED (GPIO-controlled)
* 2x button
* JBOOT bootloader
The status led has been assigned to the dwr-922-e2:green:signalstrength
(lte signal strength) led. At the end of the boot it is switched off and
is available for lte operation. Works correctly also during sysupgrade
operation.
Installation:
Apply factory image via d-link http web-gui, or via recovery interface:
How to recover/revert to OEM firmware:
1.) Push and hold the reset button and turn on the power. Wait until all
LEDs start rapidly blinking (~10sec.)
2.) DHCP should give you an IP in the 192.168.123.0/24 subnet, or set
one manually
3.) Upload original factory image via JBOOT http interface at IP
192.168.123.254
4.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.binhttp://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
5.) You can optionally telnet to 192.168.123.254 before or during the
upload and it will report the flashing status, memory address etc.
6.) Once web UI and/or telnet says "Success", power cycle the router, or
type "reboot" into the telnet session.
Signed-off-by: Simon Quigley <squigley@squigley.net>
[squashed commits, word wrap commit message, rename signal strenght led
name to match what is used for the DWR-921-C1 since they share the led
configuration, add label referenced in the aliases node]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The WD MyBook Live SquashFS images didn't work anymore due to
a upstream regression in f2fs commit: 0cfe75c5b01199
("f2fs: enhance sanity_check_raw_super() to avoid potential overflows")
that got backported to 4.14.86 and landed in 4.18.
by Martin Blumenstingl:
|Treat "block_count" from struct f2fs_super_block as 64-bit little endian
|value in sanity_check_raw_super() because struct f2fs_super_block
|declares "block_count" as "__le64".
|
|This fixes a bug where the superblock validation fails on big endian
|devices with the following error:
| F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
| F2FS-fs (sda1): Can't find valid F2FS filesystem in 1th superblock
| F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
| F2FS-fs (sda1): Can't find valid F2FS filesystem in 2th superblock
|As result of this the partition cannot be mounted.
|
|With this patch applied the superblock validation works fine and the
|partition can be mounted again:
| F2FS-fs (sda1): Mounted with checkpoint version = 7c84
|
|My little endian x86-64 hardware was able to mount the partition without
|this fix.
|To confirm that mounting f2fs filesystems works on big endian machines
|again I tested this on a 32-bit MIPS big endian (lantiq) device.
Hopefully, this will do until Martin's patch moved through upstream
to -stable.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The MyBook Live DUO used "wd,mybooklive-duo" as the first
compatible string and not "wd_mybooklive-duo".
Fixes: 9b47aa93c7 ("apm821xx: unify My Book Live Single + Duo images")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently all Archer A7 v5 have the same (incorrect) MAC address.
The address is currently derived from eth1 which is not present on the
QCA9563. Use eth0 to get the correct MAC address.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch converts the MyBook Live's recovery image to utilize the
multi-image method which integrates the device-tree binary directly
into the image.
The new initramfs can be loaded through the MyBook Live's U-boot
in the following way:
=> setenv ipaddr 192.168.1.1
=> setenv serverip 192.168.1.2
=> sata init; run addtty; tftp $kernel_addr_r wd_mybooklive-initramfs.bin; bootm
Waiting for PHY auto negotiation to complete... done
ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0)
Using ppc_4xx_eth0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'wd_mybooklive-initramfs.bin'.
Load address: 0x1000000
Loading: ################################################ [...]
done
[...]
Booting kernel from Legacy Image at 01000000 ...
Image Name: initramfs
Image Type: PowerPC Linux Multi-File Image (gzip compressed)
[...]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch fixes the build regression on 4.14 build
due to dt-bindings/dma/dw-dmac.h MIA.
apm82181.dtsi:24:10: fatal error: dt-bindings/dma/dw-dmac.h: No such file or directory
Fixes: 32141c183a ("apm821xx: add linux 4.19 apm821xx patches")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It's same for Bullet and Nanostation so far, so let's hope it's going to
be the same for other boards sharing the same platform.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It's not necessary as it's already defined in ar934x.dtsi to:
pll-data = <0x16000000 0x00000101 0x00001616>;
And in ar71xx it's currently set to the same values:
#define AR934X_PLL_VAL_1000 0x16000000
#define AR934X_PLL_VAL_100 0x00000101
#define AR934X_PLL_VAL_10 0x00001616
And dumping the value from the airOS v6.1.7 has the same value:
AR934X_PLL_ETH_XMII_CONTROL_REG 0x1805002C 0x101
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently there is no LED signalization for various system states
implemented in diag.sh, so this patch adds support for it.
Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch updates the apm821xx target to use the 4.19 kernel.
4.19 ships with all the crypto4xx driver patches. Furthermore,
the DW-DMA fix for the SATA controller has been backported from
4.20 and integrated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|In the patch "usb: simplify usbport trigger" together with
|"leds: triggers: add device attribute support" caused an
|regression for the usbport trigger. it will no longer
|enumerate any "ports" (i.e the sysfs directory stays empty)
|if the usb host drivers are fully initialized before the
|usbport trigger was loaded.
<https://marc.info/?l=linux-usb&m=154577101631079>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Thanks to the ledtrig-usb.c the USB LED trigger can be
setup in the device-tree definition for the Asus RT-AC58U
and ZyXEL NBG6617.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch fixes a kernel warning that got triggered by 4.19
because of a bad/missing interrupt level definition in the DTS.
| WARNING: CPU: 2 PID: 1996 at drivers/irqchip/irq-gic.c:1016
| CPU: 2 PID: 1996 Comm: kmodloader Not tainted 4.19.9 #0
| Hardware name: Generic DT based system
| [<c0317884>] (warn_slowpath_null) from [<c04f9cd0>]
| [<c04f9cd0>] (gic_irq_domain_translate) from [<c035af30>]
| [<c035af30>] (irq_create_fwspec_mapping) from [<c035b1e0>]
| [<c035b1e0>] (irq_create_of_mapping) from [<c0614eec>]
| [<c0614eec>] (of_irq_get) from [<c0614f3c>]
| [<c0614f3c>] (of_irq_to_resource) from [<c0614ff0>]
| [<c0614ff0>] (of_irq_to_resource_table) from [<c0610e08>]
| [<c0610e08>] (of_device_alloc) from [<c0610ea0>]
| [<c0610ea0>] (of_platform_device_create_pdata)
| [<c061120c>] (of_platform_bus_create)
| [<c06113c4>] (of_platform_populate)
| [<bf4c06b4>] (dwc3_qcom_probe [dwc3_qcom])
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Robert Marko <robimarko@gmail.com> noted in
"ipq40xx: Use kmod-usb-dwc3-qcom by default":
| Since 4.18 we cant use DWC3 OF Simple anymore so we
| have to use kmod-usb-dwc3-qcom.
This patch adds a TODO right next to the KERNEL_PATCHVER so
it will be picked up when moving to 4.19.
I would also like to point out:
All users/devs that are compiling their own images from source
and have a existing 4.14 config and want to switch to 4.19:
Please drop kmod-usb-dwc3-of-simple and add kmod-usb-dwc3-qcom
module package. Otherwise, the USB port on your router will no
longer work.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
- 4.19 no longer refuses to initialize the mdio bus if
a phy is not connected.
- fix partition unit-address
- restrict partition offset and size to 32-bit integers.
- add note to warn people not to mess with the ubi
partition size.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Upstream commit:
80483c3abf8 ("ARM: qcom: Cleanup/Remove unnecessary board file")
removed all the platform device compatibles stating that:
"This patch removes the unnecessary board file. The generic machine
definition is sufficient for the Qualcomm platforms."
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
- make the device userspace integration (WIFI,MAC,sysupgrade)
work again by renaming the ubi to UBI_DEV as a temporary measure.
In the future, once 4.14 support is dropped, this can all be
refactored again. *sigh*
- use the wifi0 and wifi1 labels
- follow Device-Tree Release v0.2 2.2.2 Generic Names Recommendation
- fix duplicated partition node-names
- remove qcom,ipq4019 platform compatible. it's no longer needed
(and wrong because the chip is a qcom,ipq4018).
Fixes: 4c67f3ad78d ("ipq40xx: Adapt 4.19 DTS for upstream SPI-NAND driver")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
IPQ40xx series has a HW pseudo random number generator built in.
It already has a node in the upstream ipq4019.dtsi so we just need to enable it.
Its driver has been rewritten to use crypto API so we dont have char interface like under 4.14 kernel.
Signed-off-by: Robert Marko <robimarko@gmail.com>
DTC was throwing warnings like this:
image-qcom-ipq4018-jalapeno.dtb: Warning (avoid_unnecessary_addr_size): /soc/spi@78b5000/m25p80@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
image-qcom-ipq4018-jalapeno.dtb: Warning (avoid_unnecessary_addr_size): /soc/spi@78b5000/spi-nand@1: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
So lets fix this for our downstream boards.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since 4.19 upstream kernel provides generic SPI-NAND
framework and vendor specific drivers.
Since only users of MT29F are 2 boards with Winbond
W25N01GV SPI-NAND for which support has been backported
from 4.20 we can drop the ever stuck in staging MT29F
driver and instead use the upstream driver.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [squashed]
This adds the necessary patches for 4.19 kernel.
Upstreamed patches were dropped, backported upstreamed patches
from 4.20.
Drop Winbond ID patch since that NAND IC was upstreamed to use
SPI-NAND framework and support for it was backported from 4.20.
Rework ESSEDMA patches to compile under 4.19 due to timer changes,
Clément Péron did the hard work and his changes were taken from the
initial 4.19 PR.
MR33 changes had to be manually refreshed to apply.
Refresh other patches to apply.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
There is also a Micro-B USB-port present but this only seems to be a
dummy as the circuit next to it is not present (at least in my unit).
It is also not mentioned in the devolo manual.
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
1x Atheros AR8033
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds support for TP-Link Archer C7 v5, leveraging most effort
from commit ea9baee and 1e4ee63. Archer C7 v5 is identical to Archer A7 v5
but with a different flash layout.
Specification:
- QCA9563 SoC (750 MHz)
- 128 MiB of RAM (DDR2)
- 16 MiB of flash (SPI)
- 5x 1 Gbps Ethernet (1x WAN + 4x LAN)
- 2.4GHz (bgn) SoC internal + 5GHz (ac) QCA9880
- 10x LED, 2x button
- UART header on PCB
Flash instructions:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-factory.bin
via web interface.
Flash instructions using TFTP recovery:
1. Plug PC to one of the LAN ports
2. Set PC to fixed IP address 192.168.0.66
3. Rename the factory image to ArcherC7v5_tp_recovery.bin and place it in
TFTP root directory
4. Turn on the router with the reset button pressed for about 15 secs
5. Release the button and wait about 150 secs to complete flashing
Signed-off-by: TOCK Chiu <tock.chiu@gmail.com>
Even with squashfs brcm2708 requires ROOTFS_PART_SIZE because the overlay
exists as a loopback device on the space not used by squashfs in the root
partition. Also for ext4 (the other fs option) ROOTFS_PART_SIZE is required,
so use feature flag rootfs-part to enable it.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The rootfs-part feature flag ensures that
CONFIG_ROOTFS_PART_SIZE symbol will be present
at all times.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Start 03x with 030 instead of 035. It's a trivial change that adds more
place for further backports in the 03x space.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The configuration option was renamed with kernel 4.19 from
CONFIG_CC_STACKPROTECTOR to CONFIG_STACKPROTECTOR adapt the code to set
both options.
CONFIG_STACKPROTECTOR now sets the regular stack protector and
CONFIG_STACKPROTECTOR_STRONG activates the additional protection of more
functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With kernel 4.19 new configuration options for the compiler were added.
These are automatically selected and set, instead of having them in each
target configuration, put them into the generic configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_COMPAT_BRK disables the heap randomization which is only needed
for very old and ancient user space applications, I am not aware that we
run any of these, just deactivate this option for these targets to allow
heap randomization.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Driver has been updated upstream to support more precise DT binding and
avoid mapping conflicts between pinctrl and USB 2.0 PHY.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Backport https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=adcc81f148d733b7e8e641300c5590a2cdc13bf3
"Mapping the delay slot emulation page as both writeable & executable
presents a security risk, in that if an exploit can write to & jump into
the page then it can be used as an easy way to execute arbitrary code.
Prevent this by mapping the page read-only for userland, and using
access_process_vm() with the FOLL_FORCE flag to write to it from
mips_dsemul().
This will likely be less efficient due to copy_to_user_page() performing
cache maintenance on a whole page, rather than a single line as in the
previous use of flush_cache_sigtramp(). However this delay slot
emulation code ought not to be running in any performance critical paths
anyway so this isn't really a problem, and we can probably do better in
copy_to_user_page() anyway in future.
A major advantage of this approach is that the fix is small & simple to
backport to stable kernels.
Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 432c6bacbd0c ("MIPS: Use per-mm page to execute branch delay slot instructions")"
Without patch:
cat /proc/self/maps
00400000-0047a000 r-xp 00000000 1f:03 1823 /bin/busybox
00489000-0048a000 r-xp 00079000 1f:03 1823 /bin/busybox
0048a000-0048b000 rwxp 0007a000 1f:03 1823 /bin/busybox
77ec8000-77eed000 r-xp 00000000 1f:03 2296 /lib/libgcc_s.so.1
77eed000-77eee000 rwxp 00015000 1f:03 2296 /lib/libgcc_s.so.1
77eee000-77f81000 r-xp 00000000 1f:03 2470 /lib/libc.so
77f90000-77f92000 rwxp 00092000 1f:03 2470 /lib/libc.so
77f92000-77f94000 rwxp 00000000 00:00 0
7f946000-7f967000 rw-p 00000000 00:00 0 [stack]
7fefb000-7fefc000 rwxp 00000000 00:00 0
7ffac000-7ffad000 r--p 00000000 00:00 0 [vvar]
7ffad000-7ffae000 r-xp 00000000 00:00 0 [vdso]
Patch applied:
cat /proc/self/maps
00400000-0047a000 r-xp 00000000 1f:03 1825 /bin/busybox
00489000-0048a000 r-xp 00079000 1f:03 1825 /bin/busybox
0048a000-0048b000 rwxp 0007a000 1f:03 1825 /bin/busybox
77ed0000-77ef5000 r-xp 00000000 1f:03 2298 /lib/libgcc_s.so.1
77ef5000-77ef6000 rwxp 00015000 1f:03 2298 /lib/libgcc_s.so.1
77ef6000-77f89000 r-xp 00000000 1f:03 2474 /lib/libc.so
77f98000-77f9a000 rwxp 00092000 1f:03 2474 /lib/libc.so
77f9a000-77f9c000 rwxp 00000000 00:00 0
7fbed000-7fc0e000 rw-p 00000000 00:00 0 [stack]
7fefb000-7fefc000 r-xp 00000000 00:00 0
7fff6000-7fff7000 r--p 00000000 00:00 0 [vvar]
7fff7000-7fff8000 r-xp 00000000 00:00 0 [vdso]
Note lack of write permission to 7fefb000-7fefc000
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The range of pinmux reg property "<0x1804002c 0x40>" for QCA955x
SoC does not includes GPIO_FUNCTION register.
Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
Atheros QCA9563.
Specification:
- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2.4/5 GHz wifi
- 2.4 GHz: 2T2R (SoC internal)
- 5 GHz: 1T1R (QCA9887)
- 4x 10/100/1000 Mbps Ethernet
- 8x LEDs, 3x keys (2x buttons, 1x slide-switch)
- UART through-hole on PCB (J2)
- Vcc, GND, NC, TX, RX from SoC side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port on WG800HP
2. Connect power cable to WG800HP and turn on it
3. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
I moved xor-image into image-commands.mk to use it in ath79 target.
It required for NEC WG800HP.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The range of pinmux reg property "<0x1804002c 0x40>" for QCA956x SoC
does not includes GPIO_FUNCTION register.
If the device uses "&jtag_disable_pins", this causes the following
errors:
[ 1.982937] pinctrl-single 1804002c.pinmux: mux offset out of range: 0x40 (0x40)
[ 1.990622] pinctrl-single 1804002c.pinmux: could not add functions for pinmux_jtag_disable_pins 64x
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Refresh all patches
Remove upstream patch:
backport-4.14/424-v4.20-net-dsa-fix-88e6060-roaming.patch
Minor tweak to generic/hack-4.14/902-debloat_proc.patch to cleanly apply
after upstream changes.
Tested-on: ath79
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The ZyXEL NBG6617 USB LED was not working with the default images.
It turned out that kmod-usb-ledtrig-usbport was missing from the
default installation.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In the past, the MX60(W)'s recovery images always had problems
with the size restriction and never really worked without manual
intervention. But starting with 4.19, the MX60(W)'s kernel image
outgrew the allocated space for sysupgrade images as well. Hence
This patch reworks the initramfs, which allows the device to ease
up on the impossible tight kernel size requirements for the
sysupgrade creation and packaging. And as a result, the now
orphaned special ramdisk setup is removed in the process.
This new initramfs can be loaded through the MX60(W) U-boot
in the following way:
=> setenv bootargs console=ttyS0,$baudrate
=> tftpboot $meraki_loadaddr meraki_mx60-initramfs-kernel.bin
[...]
Load address: 0x800000
Loading: ################################################ [...]
done
[...]
=> bootm $fileaddr
\## Booting kernel from Legacy Image at 00800000 ...
...
Updated Flashing instructions for new installations which integrates
the new recovery method. Users of existing installations that only
want to sysupgrade don't need to update their existing u-boot env.
=> setenv owrt_load1 ubi read \${meraki_loadaddr} kernel
=> setenv owrt_load2 ubi read \${meraki_loadaddr} recovery
=> setenv lede_bootkernel bootm \${meraki_loadaddr_kernel} - \${meraki_loadaddr_fdt}
=> setenv owrt_bootkernel bootm \${meraki_loadaddr}
=> setenv owrt_bootargs setenv bootargs console=ttyS0,\${baudrate} rootfstype=squashfs mtdoops.mtddev=oops
=> setenv owrt_boot run meraki_ubi owrt_bootargs\; run owrt_load1 meraki_checkpart lede_bootkernel\; run owrt_load2 owrt_bootkernel
=> setenv bootcmd run owrt_boot
=> saveenv
For more information and the latest flashing guide:
please visit the OpenWrt Wiki Page for the MR60:
<https://openwrt.org/toh/meraki/mx60#flashing>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit removes the fixed kernel size-padding for the Netgear
DNI image creation as it is not necessary for a working image.
The fake rootfs still needs to be padded to the blocksize.
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Without this patch PowerCloud CR5000 AR9382 PCIe 5GHz Wifi uses
the mac address from eeprom instead the one specified when
initializing the PCIe chip. There were two issues:
1) ap94_pci_init on the second PCIe wmac is wrong as there is only one
PCIe wmac on this device (the other wmac is the AR1022/AR9342 SoC wmac).
2) Without specifying pdata->use_eeprom there is a failure to load
firmware and caldata.
Thanks to Christian Lamparter (@chunkeey) for the heavy lifting and
help. [0]
[0] <https://github.com/openwrt/openwrt/pull/1613>
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
This patch, in a variety of forms, has been around since beginning 2016
as e756c2bb07, ending up in present form 0aa6c7df60 (kernel 4.4.13 bump)
and carried forward ever since.
There have been a number of MIPS kernel memory handling changes since,
including VDSO fixes that meant openwrt patches have been dropped with
no apparent fallout.
Simple tests (ntfs-3g) on a HIGHMEM 512MB mt7621 device have not turned
up data corruption issues which would otherwise be expected. Similarly
running on other MIPS based devices for the past 2 months hasn't turned
up anything obvious to retain this out of tree patch.
With thanks to Rosen Penev for testing on the known 'highmem' device and
Felix Fietkau for testing advice. Not putting acked-by as it's my fault
if it breaks :-)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Patch generation process:
- rebase rpi/rpi-4.14.y on v4.14.89 from linux-stable
- git format-patch v4.14.89
Patches skipped during rebase:
- lan78xx: Read MAC address from DT if present
- lan78xx: Enable LEDs and auto-negotiation
- Revert "softirq: Let ksoftirqd do its job"
- sc16is7xx: Fix for multi-channel stall
- lan78xx: Ignore DT MAC address if already valid
- lan78xx: Simple patch to prevent some crashes
- tcp_write_queue_purge clears all the SKBs in the write queue
- Revert "lan78xx: Simple patch to prevent some crashes"
- lan78xx: Connect phy early
- Arm: mm: ftrace: Only set text back to ro after kernel has been marked ro
- Revert "Revert "softirq: Let ksoftirqd do its job""
- ASoC: cs4265: SOC_SINGLE register value error fix
- Revert "ASoC: cs4265: SOC_SINGLE register value error fix"
- Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"
- Revert "Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends""
Patches dropped after rebase:
- net: Add non-mainline source for rtl8192cu wlan
- net: Fix rtl8192cu build errors on other platforms
- brcm: adds support for BCM43341 wifi
- brcmfmac: Mute expected startup 'errors'
- ARM64: Fix build break for RTL8187/RTL8192CU wifi
- ARM64: Enable RTL8187/RTL8192CU wifi in build config
- This is the driver for Sony CXD2880 DVB-T2/T tuner + demodulator
- brcmfmac: add CLM download support
- brcmfmac: request_firmware_direct is quieter
- Sets the BCDC priority to constant 0
- brcmfmac: Disable ARP offloading when promiscuous
- brcmfmac: Avoid possible out-of-bounds read
- brcmfmac: Delete redundant length check
- net: rtl8192cu: Normalize indentation
- net: rtl8192cu: Fix implicit fallthrough warnings
- Revert "Sets the BCDC priority to constant 0"
- media: cxd2880: Bump to match 4.18.y version
- media: cxd2880-spi: Bump to match 4.18.y version
- Revert "mm: alloc_contig: re-allow CMA to compact FS pages"
- Revert "Revert "mm: alloc_contig: re-allow CMA to compact FS pages""
- cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 with
MEDIA_SUBDRV_AUTOSELECT
- 950-0421-HID-hid-bigbenff-driver-for-BigBen-Interactive-PS3OF.patch
- 950-0453-Add-hid-bigbenff-to-list-of-have_special_driver-for-.patch
Make I2C built-in instead of modular as in upstream defconfig; also the
easiest way to get MFD_ARIZONA enabled, which is required by
kmod-sound-soc-rpi-cirrus.
Add missing compatible strings from
4.9/960-add-rasbperrypi-compatible.patch, using upstream names for
compute modules.
Add extra patch to enable the LEDs on lan78xx.
Compile-tested: bcm2708, bcm2709, bcm2710 (with CONFIG_ALL_KMODS=y)
Runtime-tested: bcm2708, bcm2710
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add kernel module for the fan on the PoE HAT for the 3B+ model in kernel
4.14. Without this, the fan will not turn on.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
