Commit Graph

2505 Commits

Author SHA1 Message Date
Chuanhong Guo
f30d588460 ramips: fix mac addresses used by Phicomm K2P
Like most mt7621 boards, Phicomm K2P stores LAN/WAN mac addresses
at 0xe000/0xe006 of factory partition.
Phicomm uses lan_mac-1 as wan_mac, while our default case in 02_network
uses lan_mac+1.

Add a special case reading lan/wan mac address for Phicomm K2P.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-25 19:59:33 +08:00
Roger Pueyo Centelles
7d684b7673 ramips: add kmod-mt7615e to Phicomm K2P images
Now that the mt76 driver supports the MT7615D chip found on these
devices, use it.

Also add the wpad-basic package.

Note: the driver supports operation on both the 2.4 GHz and the
      5 GHz bands, but not yet concurrently.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-07-25 18:24:50 +08:00
DENG Qingfang
0e6d97f961 ramips: enable Newifi D1 SD slot
Newifi D1 is shipped with an 8GB microSD card in its SD slot
Without SD driver users would not be able to use it unless manually installed

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-07-23 13:14:07 +08:00
Rafał Miłecki
1cbe0d659c treewide: sysupgrade: get rid of platform_nand_pre_upgrade()
1) nand_do_upgrade() is always called by a target code
2) nand_do_upgrade() starts with calling platform_nand_pre_upgrade()

It means there is no need for the platform_nand_pre_upgrade() callback
at all. All code that was present there could bo moved & simplly called
by a target right before the nand_do_upgrade().

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-07-22 14:27:37 +02:00
Georgi Vlaev
8c51ddeff0 ramips: add support for TP-Link RE650 v1
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.

Hardware specification:

- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
  Serial console @ 57600,8n1

Flash instructions:

Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.

TFTP recovery to stock firmware:

Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.

Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-17 23:14:23 +02:00
INAGAKI Hiroshi
cda123fe69 ramips: add MT7615 wireless support for ELECOM WRC-1167GHBK2-S
ELECOM WRC-1167GHBK2-S has a MediaTek MT7615D chip for 2.4/5 GHz
wireless.

A driver package for MT7615 chip is added to OpenWrt in
a0e5ca4f35,
so add preliminary MT7615 chip support for WRC-1167GHBK2-S.

Note: Currently, DBDC mode for MT7615 is not supported in mt76 driver.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-07-17 14:45:18 +02:00
Rafał Miłecki
8b4bc7abe0 treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()
stage2 passes image path to platform_do_upgrade() as an argument so it
can be simply accessed using $1

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-07-17 08:05:38 +02:00
Rafał Miłecki
d9593b0809 ramips: get rid of platform_pre_upgrade()
The only step between platform_pre_upgrade() and platform_do_upgrade()
is switching to ramdisk. It should be fine to "mtd erase firmware" from
the later callback and get rid of the first one.

This change wasn't tested on affected target but identical code logic
was verified to work as expected on brcm47xx with initramfs firmware.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-07-16 19:03:42 +02:00
Adrian Schmutzler
6d61fcfa9e ramips: Remove left-over mistyped device string from 02_network
In 2011 (!), network setup for nexaira,bc2 was moved to network
defaults script with a typo so it became b2c:
295e04084c ("ramips: setup bc2 mac addresses from the generic network script")

This patch just removes the useless entry without replacement,
since it seems to have worked for 8 years anyway.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-16 11:33:46 +08:00
Chuanhong Guo
fae125781e ramips: mtk-mmc: mt76x8: check ESD_MODE before applying AGPIO_CFG
Since mt76x8an ver1 eco2, SDXC pins can be switched to the
following pinmap:
sd_d1  -> PAD_I2S_SDI
sd_d0  -> PAD_I2S_WS
sd_cmd -> PAD_I2S_CLK
sd_d3  -> PAD_I2C_SCLK
sd_d2  -> PAD_I2C_SD
sd_clk -> PAD_GPIO0
sd_wp  -> PAD_TXD1
sd_cd  -> PAD_RXD1

To use this pinmap, one would need to set ESD_MODE bit (bit 15)
to 1 in GPIO1_MODE and switch other used pads into GPIO mode.
In this mode, we don't need to switch ethernet pins to digital
pad.

Check ESD_MODE bit before applying AGPIO_CFG and use rt_sysc_m32
to set it.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-16 09:50:16 +08:00
David Bauer
14e0e4f138 ramips: add support for ASUS RT-AC57U
SoC:   MediaTek MT7621AT
RAM:   128M (Winbond W631GG6KB-15)
FLASH: 16MB (Spansion S25FL128SA)
WiFi:  MediaTek MT7603EN bgn 2SS
WiFi:  MediaTek MT7612EN nac 2SS
BTN:   Reset - WPS
LED:    - Power
        - LAN {1-4}
        - WAN
        - WiFi 2.4 GHz
        - WiFi 5 GHz
        - USB
UART:  UART is present next to the Power LED.
       TX - RX - GND - 3V3 / 57600-8N1
       3V3 is the nearest one to the Power LED.

Installation
------------
Via TFTP:
1. Set your computers IP-Address to 192.168.1.75.
2. Power up the Router with the Reset button pressed.
3. Release the Reset button after 5 seconds.
4. Upload OpenWRT sysupgrade image via TFTP:
 > tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE>

Via SSH:
Note: User/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt sysupgrade image via scp:
 > scp owrt.bin admin@192.168.1.1:/tmp
4. Connect via SSH to the router.
 > ssh admin@192.168.1.1
5. Write the OpenWrt image to flash.
 > mtd-write -i /tmp/owrt.bin -d linux
6. Reboot the router
 > reboot

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-11 21:32:39 +02:00
Chuanhong Guo
53daa51cf2 ramips: fix mqmaker witi case in fixup-mac-address
This commit fixes a forgotten case in previous commit.

Fixes: 087e14ab59 ("ramips: mt7621: merge two variants of MQmaker WiTi together")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-11 23:27:06 +08:00
Chuanhong Guo
087e14ab59 ramips: mt7621: merge two variants of MQmaker WiTi together
Since we can auto-detect memory now, we don't need 2 dts for two
memory variants.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-11 22:11:21 +08:00
Chuanhong Guo
a2c19f1d2f ramips: dts: drop memory nodes
mt7621 and mt7628 now have the ability to detect memory size
automatically.
Drop memory nodes and let kernel determine memory size.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-11 22:11:21 +08:00
Chuanhong Guo
6d91ddf517 ramips: mt7621: add support for memory detection
mt7621 has the following memory map:
0x0-0x1c000000: lower 448m memory
0x1c000000-0x2000000: peripheral registers
0x20000000-0x2400000: higher 64m memory

detect_memory_region in arch/mips/kernel/setup.c only add the first
memory region and isn't suitable for 512m memory detection because
it may accidentally read the memory area for peripheral registers.

This commit adds memory detection capability for mt7621:
1. add the highmem area when 512m is detected.
2. guard memcmp from accessing peripheral registers:
     This only happens when some weird user decided to change
     kernel load address to 256m or higher address. Since this
     is a quite unusual case, we just skip 512m testing and return
     256m as memory size.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-11 22:11:21 +08:00
Daniel Golle
98d04dc4cf ramips: fix bogus MTK_SOC (typo)
Belkin F7C027 is clearly Rt5350 SoC, as shown on internal
photographs filed for FCC approval[1].

[1]: https://fcc.io/K7S/F7C027

Fixes commit 3b0264eddb
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-07-10 19:28:35 +02:00
Adrian Schmutzler
447deed52a ramips: Sort all subtarget Makefiles
This patch applies sorting to the definitions as whole blocks.

Sorting has been performed fully automatic, line count differences
originate from double empty lines removed.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
5d50155f14 ramips: Reapply sorting to board.d files
This patch is cosmetical:
It only applies sorting based on device names, whereas renames
already took place in earlier patches.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
e8d2d97498 ramips: Remove base-files/lib/ramips.sh
Having converted the target to use device compatible, ramips.sh
is obsolete now.

The only remaining entry for the mt7688 evaluation board seems to
be orphaned.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
3b0264eddb ramips/rt305x: Name DTS files based on scheme
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
6a104ac772 ramips/rt288x,rt3883: Name DTS files based on scheme
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
b97a99256f ramips/mt76x8: Name DTS files based on scheme
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
7196ca1d49 ramips/mt7621: Name DTS files based on scheme
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
48047b3a5c ramips/mt7620: Name DTS files based on scheme
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
402138d12d ramips: Derive DTS name from device name in Makefile
This will automatically derive the DTS name as in ath79 and thus
makes specifying DTS for every device obsolete.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

---

This patch only introduces the mechanism and is then followed by
commits with renames and Makefile adjustments per subtarget.

Eventually, those can be all squashed into a single commit or left
as they are to enhance overview.
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
7dd3a234be ramips/rt305x: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
83efa8329b ramips/rt288x,rt3883: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
c2334ad60d ramips/mt76x8: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
2f2a319f82 ramips/mt7621: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
9f99000165 ramips/mt7620: Synchronize Makefiles with DTS compatible
This will "rename" devices in Makefiles to the pattern used in
DTS compatible. This will systematize naming of devices
enormously.

As device names are used to for default SUPPORTED_DEVICES entries,
we need to adjust the source for /tmp/sysinfo/board_name, too.
So remove relevant entries from base-files/lib/ramips.sh and
use device compatible for that.

Despite that, base-files are updated, too.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
d93969a13a ramips: Improve compatible for TP-Link Archer devices
Include "Archer" in compatible as it is part of the device name.

Update Makefile device names where necessary to match compatible.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:28 +02:00
Daniel Golle
c2b1baf767 ramips: add missing DEVICE_VENDOR
Fixes commit ee66fe4ea9
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-07-10 17:15:49 +02:00
Chuanhong Guo
7a8d3432c7 ramips: use upstream RAW_APPENDED_DTB instead of our OWRTDTB
Upstream kernel added support for RAW_APPENDED_DTB on ralink arch
in the following commit:
02564fc89d3d ("ralink: Introduce fw_passed_dtb to arch/mips/ralink")

Use upstream solution and get rid of our OWRTDTB hack.
This commit set DEVICE_DTS to $$(DTS) instead of replacing DTS with
DEVICE_DTS in device profile because DTS variable will be dropped
in later commits.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on mt7621/mt76x8]
Tested-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on rt305x/mt7620]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-07-08 22:00:24 +02:00
Adrian Schmutzler
c017ead66e ramips: Fix compatible for YUKAI Engineering BOCCO
Looks like an undetected copy/paste error.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-07 13:02:05 +02:00
Daniel Golle
ee66fe4ea9 ramips: convert DEVICE_TITLE to new variables
Also unify naming and add details where they were missing.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-07-06 14:58:03 +02:00
Alexander Müller
3fd97c522b
ramips: add support for TP-Link TL-WR841n v14
TP-Link TL-WR841n v14 is a router based on MediaTek MT7628N.

- MediaTek MT7628NN
- 32 MB of RAM
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet

Installation:
- copy the
  'openwrt-ramips-mt76x8-tl-wr841n-v14-squashfs-tftp-recovery.bin'
  file to your tftp server root and rename it to 'tp_recovery.bin'.
- configure your PC running the TFTP server with the static IP address
  192.168.0.66/24
- push the reset button and plug in the power connector. Wait until
  the orange led starts blinking (~6sec)

Signed-off-by: Alexander Müller <donothingloop@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu> [small modifications gpio-hog]
2019-07-02 16:17:49 +02:00
Alexander Couzens
cc1147072d ramips/leds: use devicetree alias led_wlan
Similiar to the lantiq target use a dts alias to define the wlan led
instead of static mapping in /etc/board.d/01_leds. Reduce code
duplication.
A device tree must define the alias "led-wlan" similiar to "led-boot".

/ {
        aliases {
                led-wlan = &led_wlan;
        };

        [..]

        led_wlan: wlan {
            label = "tl-wr841n-v14:green:wlan";
            gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
        };
};

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2019-07-02 16:05:28 +02:00
Chuanhong Guo
3f68cffd27 ramips: add support for TOTOLINK A7000R
Specifications:
- SoC: MT7621AT
- RAM: 128MB
- Flash: 16M SPI NOR
- Ethernet: 5x GE ports
- WiFi: 2.4G: MT7615N
        5G: MT7615N

Flash instruction:
Upload generated sysupgrade firmware through factory web interface.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-26 07:41:54 +02:00
Chuanhong Guo
110daa16e4 ramips: mt7621: add IRQ for GPIO node
This makes interrupt-based gpio-keys working.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-26 07:41:54 +02:00
Daniel Danzberger
029c970464 ramips: mt7621: Add new device AsiaRF AP7621-001
Hardware specs:
SoC:	Mediatek MT7621A
CPU:	4x 880Mhz
Cache:	32 KB I-Cache and 32 KB D-Cach
	256 KB L2 Cache (shared by Dual-Core)
RAM:	DDR3 512MB 16bits BUS
FLASH:	16MB
Switch:	Mediatek Gigabit Switch (1 x LAN, 1 x WAN)
USB:	1x 3.0
PCI:	3x Mini PCIe
GPS:	Quectel L70B
BTN:	Reset
LED:	- Power
	- Ethernet
	- Wifi
	- USB
UART:	UART is present as Pads with throughholes on the PCB.
	They are located on left side.
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation:
The stock image is a modified openwrt and can be overflashed via
 # sysupgrade -F image.bin

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed unused label, formatting]
2019-06-25 15:02:21 +02:00
Koen Vandeputte
6592dddd15 kernel: bump 4.14 to 4.14.128
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-20 15:48:48 +02:00
Petr Štetiar
783e37502f ramips: fix EW-7478AC model name in DTS
This fixes lower case AC in the DTS model name.

Fixes: 88f7a29f99 ("ramips: add support for Edimax EW-7476RPC / EW-7478AC")
Reported-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-20 12:47:19 +02:00
Pawel Dembicki
eeeaf24e28 ramips: fix GELAN port in D-Link DWR-118-A2
This patch fix and enable GELAN port in D-LINK DWR-118-A2.

Tested-by: Richard Toth <trtk1992@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-06-20 08:48:20 +02:00
Pawel Dembicki
391df37829 ramips: mt7620: add EPHY base mdio address changing possibility
In some boards is requred to change the ephy mdio base address.

This patch add of property "mediatek,ephy-base-address" in gsw
part, which allows to change ephy base address.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed indentation in header file]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-20 08:48:19 +02:00
Pawel Dembicki
c02a9a2514 ramips: mt7620: fix external PHY autopolling
The port initialisation is based on assumption that phy address and
port number is the same. SoC allow different numbers and some board
have it.

Use phy address instead the port number to make sure that correct
addresses are polled.

In situation when only one PHY with address 0x0 is conected to
port 4, autopolling is broken.

This patch make autopolling correct when port number and phy address
are different.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-06-20 08:48:19 +02:00
Mathias Kresin
f96c7f697f ramips: handle mdio address and switch port seperate
The phy handling code forces a phy mdio address and the switch port to
which a phy is attached to be the same. Albeit such a configuration is
used for most boards, it isn't for all.

Pass the switch port number to the ethernet phy connect functions, to
ensure the correct list entry is edited and not the list entry that
matches th phys mdio address.

Use the mdio address with mdiobus_get_phy instead of the port number,
to make sure the expected ethernet phy gets connected.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-06-20 08:48:19 +02:00
Mathias Kresin
fb423f6e01 ramips: ignore already handled ethernet phys
The whole logic in fe_phy_connect() is based on the asumption that mdio
address and switch port id are equal. Albeit it is true for most
boards, it doesn't is for all.

It isn't yet clear which subtargets/boards require the devicetree less
ethernet phy handling. Hence change the code in a way that it doesn't
touch ethernet phys which were early attached and are already handled.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-06-20 08:48:19 +02:00
Birger Koblitz
ab7f8146fd ramips: add support for Edimax EW-7478APC
SoC:	MediaTek MT7620a @ 580MHz
RAM:	64M (Winbond W9751G6KB-25)
FLASH:	8MB (Macronix)
WiFi:	SoC-integrated: MediaTek MT7620a bgn
WiFi:	MediaTek MT7612EN nac
Switch: Mediatek MT7530W Gigabit Switch (4 x LAN, 1 x WAN)
USB:	Yes 1 x 2.0 (+ 1 x 2.0 unpopulated header)
BTN:	Reset/WPS
LED:    - Power (white)
	- Internet (blue)
	- Wifi (blue)
	- USB (blue)
UART:  UART is present as Pads with throughholes on the PCB. They are
       located in the lower right corner (GbE ports facing up)
       3.3V - RX - GND - TX / 57600-8N1
       3.3V is the square pad

Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimax.setup)

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflicts in 01_leds and mt7620.mk, dts whitespace issues]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-20 08:48:19 +02:00
Birger Koblitz
88f7a29f99 ramips: add support for Edimax EW-7476RPC / EW-7478AC
SoC:	MediaTek MT7620a @ 580MHz
RAM:	64M (Winbond W9751G6KB-25)
FLASH:	8MB (Macronix)
WiFi:	SoC-integrated: MediaTek MT7620a bgn
WiFi:	MediaTek MT7612EN nac
GbE:	1x (RTL8211E)
BTN:	WPS - RFKILL/RF 50%/RF 100% toggle
LED:	- Wifi 5g (blue)
	- Wifi 2g (blue)
	- Crossband (green)
	- Power (green)
	- WPS (green)
	- LAN (Green)
UART:	UART is present as Pads with throughholes on the PCB. They are
	located next to the switch for the wifi configuration
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation
------------
Update the factory image via the web-interfaces (by default:
192.168.9.2/24).
http://192.168.9.2/index.asp

ramips: add Edimax EW-7478AC

SoC:	MediaTek MT7620a @ 580MHz
RAM:	64M (Winbond W9751G6KB-25)
FLASH:	8MB (Macronix)
WiFi:	SoC-integrated: MediaTek MT7620a bgn
WiFi:	MediaTek MT7612EN nac
GbE:	1x (RTL8211E)
BTN:	WPS - RFKILL/RF 50%/RF 100% toggle
LED:	- Wifi 5g (blue)
	- Wifi 2g (blue)
	- Crossband (green)
	- Power (green)
	- WPS (green)
	- LAN (Green)
UART:	UART is present as Pads with throughholes on the PCB. They are
	located next to the switch for the wifi configuration
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimaxext.setup)
Or push wpa button on power on and send firmware via tftp to 192.168.1.6

The EW-7478AC is identical to the EW-7476RPC, except instead of 2 internal
antennas it has 2 external ones.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflict in 01_leds]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-20 08:31:24 +02:00
Koen Vandeputte
a7e68927d0 kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)
Refreshed all patches.

This bump contains upstream commits which seem to avoid (not properly fix)
the errors as seen in FS#2305 and FS#2297

Altered patches:
- 403-net-mvneta-convert-to-phylink.patch
- 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch

Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-12 15:04:09 +02:00
Kristian Evensen
86b6d31e6e ramips: Remove redundant LED-cases
01_leds has several redundant LED-cases. This commit cleans
up the file by merging these cases into shared cases.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-06-10 11:25:47 +02:00
Deng Qingfang
b47cf6d539 ramips: mt7620: select kmod-rt2800-pci driver for RT5592
ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless
After commit 367813b9b1 the driver for RT5592 (rt2800pci)
is not selected by default anymore, which broke their 5GHz wireless
Add it back to device packages

Fixes: 367813b9b1 ("ramips: mt7620: fix dependencies")

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-06-10 11:25:47 +02:00
Chuanhong Guo
0ab9f283f7 ramips: add support for TOTOLINK LR1200
Specifications:
- SoC: MT7628DAN (MT7628AN with 64MB built-in RAM)
- Flash: 8M SPI NOR
- Ethernet: 5x 10/100Mbps
- WiFi: 2.4G: MT7628 built-in
        5G: MT7612E
- 1x miniPCIe slot for LTE modem (only USB pins connected)
- 1x SIM slot

Flash instruction:
U-boot has a builtin web recovery page:
1. Hold the reset button while powering it up
2. Connect to the ethernet and set an IP in 192.168.1.0/24 range
3. Open your browser and upload firmware through http://192.168.1.1

Note about the LTE modem:
If your router comes with an EC25 module and it doesn't show up
as a QMI device, you should do the following to switch it to QMI
mode:
1. Install kmod-usb-serial-option and a terminal software
   (e.g. minicom or screen). All 4 serial ports of the modem
   should be available now.
2. Open /dev/ttyUSB3 with the terminal software and type this
   AT command: AT+QCFG="usbnet",0
3. Power-cycle the router. You should now get a QMI device
   recognized.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-05 10:26:33 +02:00
Pawel Dembicki
9b7abd9fe2 ramips: mt7620: fix 5GHz WiFi LED on DWR-118-A1
Support for D-Link DWR-118 A1 was added before LEDs feature
in mt76x0e driver.

This fixes the 5GHz WiFi LED which was previously inverted.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-06-05 10:12:30 +02:00
Petr Štetiar
bf58bc3bd8 ramips: ethernet: remove unused SIOCETHTOOL ioctl handling
This ioctl is currently routed through generic interface code.

  dev_ioctl
    dev_ethtool
      __ethtool_get_link_ksettings
        phy_ethtool_ioctl

Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:12:30 +02:00
Jan Hoffmann
085f66de9a ramips: create R6220 dtsi and improve WNDR3700v5 support
The R6220 and WNDR3700v5 are identical apart from using NAND/NOR flash and
having a different casing. This adds a new cleaned up R6220.dtsi with the
common bits for both devices. Both devices now have feature parity.

Performed cleanup:
 * generic DTS node names
 * regulator for usb power
 * added missing pinctrl groups
 * use switch port instead of VLAN as trigger for WAN LED

Fixes for WNDR3700v5:
 * all LEDS work
 * correct ethernet MAC addresses

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2019-05-31 11:21:22 +02:00
Markus Scheck
5ff5c9bce6 ramips: add support for Xiaomi Mi Router 4A (100M Edition)
- SoC:      MediaTek MT7628AN
- Flash:    16MB (Winbond W25Q128JV)
- RAM:      64MB
- Serial:   As marked on PCB, 3V3 logic, baudrate is 115200
- Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN)
- WIFI0:    MT7628AN 2.4GHz 802.11b/g/n
- WIFI1:    MT7612EN 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs:     Programmable power-LED (two-colored, yellow/blue)
            Non-programmable internet-LED (shows WAN-activity)
- Buttons:  Reset

INSTALLATION:

1. Connect to the serial port of the router and power it up.
   If you get a prompt asking for boot-mode, go to step 3.
2. Unplug the router after
       > Erasing SPI Flash...
       > raspi_erase: offs:20000 len:10000
   occurs on the serial port. Plug the router back in.
3. At the prompt select option 2 (Load system code then
   write to Flash via TFTP.)
4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the
   Server-IP.
5. Connect your computer to LAN1 and assign it as 192.168.1.2/24.
6. Rename the sysupgrade image to test.bin and serve it via TFTP.
7. Enter test.bin on the serial console and press enter.

Signed-off-by: Markus Scheck <markus@mscheck.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added mt76 compatible]
2019-05-31 11:21:22 +02:00
Davide Fioravanti
7c91144ae6 ramips: add CUDY WR1000 support
Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas

Specifications:

MT7628 (580 MHz)
64 MB of RAM (DDR2)
8 MB of FLASH
2T2R 2.4 GHz (MT7628)
2T2R 5 GHz (MT7612E)
3x 10/100 Mbps Ethernet (2 LAN + 1 WAN)
2x external, non-detachable antennas (5dbi)
UART header on PCB (57600 8n1)
7x LED, 2x button

Known issues:
The Power LED is always ON, probably because it is connected
directly to power.

Flash instructions
------------------
Load the ...-factory.bin image via the stock web interface.

Openwrt upgrade instructions
----------------------------
Use the ...-sysupgrade.bin image for future upgrades.

Revert to stock FW
------------------
Warning! This tutorial will work only with the following OEM FW:
  WR1000_EU_92.122.2.4987.201806261618.bin
  WR1000_US_92.122.2.4987.201806261609.bin
If in the future these firmwares will not be available anymore,
you have to find the new XOR key.

1) Download the original FW from the Cudy website.

   (For example WR1000_EU_92.122.2.4987.201806261618.bin)

2) Remove the header.

   dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64

3) XOR the new file with the region key.

   FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D
   FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C

   You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this:

   xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767..

   Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!):
   https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false)

4) Check the resulting decrypted image.

   Check if bytes from 0x20 to 0x3f are:
   4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00

   Alternatively, you can use u-boot's tool dumpimage tool to check
   if the decryption was successful. It should look like:

   # dumpimage -l stock-firmware.bin
   Image Name:   Linux Kernel Image
   Created:      Tue Jun 26 10:24:54 2018
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    4406635 Bytes = 4303.35 KiB = 4.20 MiB
   Load Address: 80000000
   Entry Point:  8000c150

5) Flash it via forced firmware upgrade and don't "Keep Settings"

   CLI: sysupgrade -F -n stock-firmware.bin

   LuCI: make sure to click on the "Keep settings" checkbox
         to disable it. You'll need to do this !TWICE! because
         on the first try, LuCI will refuse the image and reset
	 the "Keep settings" to enable. However a new
         "Force upgrade" checkbox will appear as well.
         Make sure to do this very carefully!

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added wifi compatible, spiffed-up the returned to stock instructions]
2019-05-31 10:36:36 +02:00
Davide Fioravanti
62ce6d58f2 ramips: unify JCG helper command definition
This patch makes the JCG helper command definition available
for every rampis target

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2019-05-31 10:30:03 +02:00
Nicholas Smith
73e0f52b6e ramips: add support for Telco Electronics X1
Hardware:
SoC:   MT7621
DRAM:  256MB DDR3
Flash: 16MB SPI-NOR
WiFi:  2.4GHz: MT7603 @ PCIe0
WiFi:  5.8GHz: MT7612 @ PCIe1
Modem: Sierra Wireless MC74xx

Interfaces:
GBE RJ45 x5
mPCIe    x2
UART     x1
I2C      x1
JTAG     x1
UIM      x1
LEDs     x6

Flash instructions:
Flash from within the factory bootloader, firmware web interface or CLI using
sysupgrade -F -n

Signed-off-by: Nicholas Smith <mips171@icloud.com>
2019-05-18 17:59:49 +02:00
Jan Hoffmann
2fdd02cc7c ramips: add factory image for WNDR3700v5
This uses the existing rules for Sercomm factory images and moves them
to the ramips image Makefile, so they can be used in all subtargets.

The new factory image for WNDR3700v5 can be flashed using nmrpflash.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2019-05-18 16:44:41 +02:00
Liu Yu
671c9d16e3 ramips: add support for HILINK HLK-7628N
Specification:

CPU:       MT7628 580 MHz. MIPS 24K
RAM:       128 MB
Flash:     32 MB
WIFI:      802.11n/g/b 20/40 MHz
Ethernet:  5 Port ethernet switch
UART:      2x

Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART0 line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
   set device and tftp server IP address and input the firmware
   file name. U-boot will then load the firmware and write it into
   the flash.
5. After firmware is started connect via ethernet at 192.168.1.1

Signed-off-by: Liu Yu <f78fk@live.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed dupped subject]
2019-05-18 13:43:55 +02:00
Kristian Evensen
869376710d ramips: Add support for ZBT WE826-E
ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the
following specifications:

- MT7620A (580 MHz)
- 128MB RAM
- 32MB of flash (SPI NOR)
- 5x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus)
- 2x SIM card slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 10x LEDs (4 GPIO-controlled)
- 1x reset button

The following have been tested and working:
- Ethernet switch
- wifi
- miniPCIe slot
- USB port
- microSD slot
- sysupgrade
- reset button

Installation and recovery:

In order to install OpenWRT the first time or recover the router, you
can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address.  Upload the firmware to start the recovery
process.

How to swap SIMs:

You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio13/value. In order for the change to take effect,
you can either use AT-commands (AT+CFUN) or power-cycle the modem (write
0/1 to /sys/class/gpio/gpio14/value).

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-05-17 21:41:43 +02:00
Kristian Evensen
52b59a984f ramips: Add support for Head Weblink HDRM200
Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed
specifications are:

- MT7620A (580MHz)
- 64MB RAM
- 16MB of flash (SPI NOR)
- 6x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM
SIM7100E LTE modem.
- 2x SIM slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 1x 5GHz wifi (mt7612)
- 1x reset button
- 1x WPS button
- 3x GPIO-controllable LEDs
- 1x 10 pin terminal block (RS232, RS485, 4 x GPIO)

Tested:
- Ethernet switch
- Wifi
- USB slot
- SD card slot
- miniPCIe-slot
- sysupgrade
- reset button

Installation instructions:

Installing OpenWRT for the first time requires a bit of work, as the
board does not ship with OpenWRT. In addition, the bootloader
automatically reboots when installing an image over tftp. In order to
install OpenWRT on the HDRM200, you need to do the following:

* Copy the initramfs-image to your tftp-root (default filename is
test.bin) and configure networking accordingly (default server IP is
10.10.10.3, client 10.10.10.123). Start your tftp server.
* Open the board and connect to UART. The pins are exposed and clearly
marked.
* Boot the board and press 1.
* Either use the default filename and client/server IP-addresses, or
specify your own.

The image should now be loaded to memory and board boot. If the router
reboots while the image is loading, you need to try again. Once the
board has booted, copy the sysupgrade-image to the router and run
sysupgrade in order to install OpenWRT to the flash.

Notes:

- You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio0/value. In order for the change to take
effect, you can either use AT-commands (AT+CFUN) or power-cycle the
modem (write 0/1 to /sys/class/gpio/gpio21/value).
- RS485 is available on /dev/ttyS0.
- RS232 is available on /dev/ttyS1.
- The name of the ioX-gpios map to the labels on the casing.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[fixed whitespace issue and merge conflict in target.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-17 21:41:43 +02:00
Koen Vandeputte
09050b6fe2 kernel: bump 4.14 to 4.14.118
Refreshed all patches.

Remove upstreamed:
- 060-v5.1-serial-ar933x_uart-Fix-build-failure-with-disabled-c.patch

Altered:
- 143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-13 19:17:41 +02:00
David Bauer
a4dc519888 ramips: fix R6120 factory image
The factory firmware omits the JFFS2 end-marker while flashing via
web-interface. Add a 64k padding after the marker fixes this problem.

When the end-marker is not present, OpenWRT won't save the overlayfs
after initial flash.

Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-05-11 16:37:11 +02:00
Deng Qingfang
367813b9b1 ramips: mt7620: fix dependencies
MT7620 integrated WMAC does not need RT2x00 PCI driver or firmware
Also corrected kmod-eeprom-93cx6 and kmod-lib-crc-itu-t dependencies
according to original Kconfig and lsmod output

This will remove some unnecessary packages from MT7620 target to
save some space

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[75 characters per line in the commit message]
2019-05-11 01:05:11 +02:00
Eike Feldmann
9e0fb5a27f ramips: add support for Rakwireless RAK633
It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or
Vocore2.

Specification:

CPU:       MT7628 580 MHz. MIPS 24K
RAM:       64 MB
Flash:     8 MB
WIFI:      802.11n/g/b 20/40 MHz
USB:       1x Port USB 2.0
Ethernet:  5 Port ethernet switch
UART:      2x

Installation: Use the installed uboot Bootloader. Connect a serial cable
to serialport 0. Turn power on.  Choose the option: "Load system code
then write to Flash via TFTP".  Choose the local device IP and the TFTP
server IP and the file name of the system image.  After if the
Bootloader will copy the image to the local flash.

Notes: The I2C Kernel module work not correctly. You can send and
receive data. But the command i2cdetect doesn’t work. FS#845

Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com>
[commit subject and message touches, DTS whitespace fixes, wifi LED
rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses,
removed i2c kernel modules]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-14 23:42:03 +02:00
David Bauer
43e8c37cb4 ramips: add support for GL.iNet VIXMINI
Hardware
--------
SoC:   MediaTek MT7628NN
RAM:   64M DDR2 (Etron EM68B16CWQD-25H)
FLASH: 8M (Winbond W25Q64JVSIQ)
LED:   Power - WLAN
BTN:   Reset
UART:  115200 8N1
       TX and RX are labled on the board as pads next to the SoC

Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
   Note: The ethernet port is by default WAN. So you need to connect to
   the router via WiFi

2. Navigate to the Update tab on the left side.

3. Select "Local Update"

4. Upload the OpenWrt sysupgrade image.
   Note: Make sure you select not to preserve the configuration.

Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
   Wait for the LED to flash 5 times.

2. Assign yourself a static IPv4 in 192.168.1.0/24

3. Upload the OpenWrt sysupgrade image at 192.168.1.1.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-13 18:46:40 +02:00
Daniel Golle
66e2acad9c ramips: fix pinctrl to allow hardware i2c on WRTNODE2R
Instead of assigning I2C pins as GPIOs by default, leave it up to the
user whether to install kmod-i2c-mt7621 and use them for hardware I2C
instead.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-04-11 22:26:28 +02:00
Kip Porterfield
b812a7fa68 ramips: correct DTS for Belkin F9K1109v1 to include switch definition
Add switch definition for the rtl8367b switch to the DTS/DTSi for
the Belkin F9K1109v1 that was mistakenly omitted from the initial
commit.

Fixes: 017ec068e3 (ramips: add support for Belkin F9K1109v1)
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
2019-04-06 19:14:06 +02:00
Chuanhong Guo
d80a1c6e2c ramips: backport mt7621-spi from linux-next-20190329
Upstream driver has gone through a series of cleanup and was moved
from drivers/staging into drivers/spi. Backport it to replace our
messy driver.

Tested-by: Jörg Schüler-Maroldt <joerg-linux@arcor.de>
[LinkIt Smart 7688, AcSIP AI7688H Wi-Fi module]
Tested-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Tian Xiao bo <peterwillcn@gmail.com>
[Newifi-D2 MediaTek MT7621 ver:1 eco:3]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-04-06 19:14:06 +02:00
David Bauer
b19c48dc34 ramips: enable R6120 USB power
Enable the USB power for the Netgear R6120. Otherwise, no power is
supplied to an attached USB device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-06 19:14:06 +02:00
Zhao Yu
32689e93c4 ramips: add support for Youku YK-L2
Hardware spec:

CPU: MTK MT7621A
RAM: 256MB
ROM: 16MB SPI Flash
WiFi: MT7603EN + MT7612EN
Button: 2 buttons (reset, wps)
LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB)
Ethernet: 3 ports, 2 LAN + 1 WAN
Other: USB3.0

Flashing instructions:

Visit the openwrt forum topic for this router:
https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692

to get the bootloader and unlock firmware.

0. upgrade your router with the telnet firmware via the
   firmware upgrade page on the webui.

1. telnet 192.168.11.1 from your PC

2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer
   it to the /tmp directory of the router.

3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader

4. turn off the power

5. Push the reset button while turning on the router and
   wait until LED start blinking (~10sec.)

6. Connect Ethernet port and goto http://192.168.1.1.

7. Upload the firmware to firmware restore page in webui.

Signed-off-by: Zhao Yu <574249312@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the
flashing instructions, fixed author]
2019-04-06 19:13:49 +02:00
Felix Fietkau
c9262a96d1 ramips: implement vlan rx offload on MT7621
Avoids the overhead of software VLAN untagging in the network stack

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-04-03 10:40:09 +02:00
David Bauer
38f3433420 ramips: add missing SPDX identifier for EX6150
This adds the SPDX license identifier for the NETGEAR EX6150. It was
missed when submitting the original patch.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-31 20:59:08 +02:00
Rosen Penev
2159b25466 ramips: Increase GB-PC1 SPI frequency to 80MHz
The specific flash chip used (W25Q256FVEM) accepts 50MHz for read
requests and higher for others. 104MHz for fast reads. ramips seems to
be limited to 80MHz based on testing with higher values (no speedup).

Based on upstream commit: 97738374a310b9116f9c33832737e517226d3722

 time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.96s to 7.01s

 [test done with backported upstream v4.19 driver[1], for numbers on
  stock 4.14 driver please take a look at `ramips: Increase GB-PC2 SPI
  frequency to 80MHz` commit message]

1. https://github.com/openwrt/openwrt/pull/1578

Signed-off-by: Rosen Penev <rosenp@gmail.com>
[expanded note about spi driver version]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 09:01:46 +01:00
Rosen Penev
274439b780 ramips: Increase GB-PC2 SPI frequency to 80MHz
The flash chip on the board (Spansion S25FL256SAIF00) is rated to
support at least 50MHz for normal read requests according to the
datasheet. 133MHz for fast reads. However, ramips seems to be limited to
80MHz.

>From testing this, higher values do not improve speeds.

time dd if=/dev/mtdblock3 of=/dev/null bs=64k from

42.82s to 14.09s.

boot speed is also faster:
[   66.884087] procd: - init - vs
[   48.976049] procd: - init -

Since spi speed was requested:
[    3.538884] spi-mt7621 1e000b00.spi: sys_freq: 225000000

CPU is 900MHz:
[    0.000000] CPU Clock: 900MHz

Signed-off-by: Rosen Penev <rosenp@gmail.com>
[fixed commit message by adding missing 0 in the spi-mt7621 clock output]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 09:01:23 +01:00
David Bauer
3f019bf96c ramips: add Netgear EX6150
SoC:   MediaTek MT7621
RAM:   64M (Winbond W9751G6KB-25)
FLASH: 16MB (Macronix MX25L12835F)
WiFi:  MediaTek MT7662E bgn 2SS
WiFi:  MediaTek MT7662E nac 2SS
BTN:   ON/OFF - Reset - WPS - AP/Extender toggle
LED:    - Arrow Right (blue)
        - Arrow Left (blue)
        - WiFi 1 (red/green)
        - WiFi 2 (red/green)
        - Power (green/amber)
        - WPS (Green)
UART:  UART is present as Pads on the backside of the PCB. They are
       located on the other side of the Ethernet port.
       3.3V - GND - TX - RX / 57600-8N1
       3.3V is the nearest one to the antenna connectors

Installation
------------
Update the factory image via the Netgear web-interfaces (by default:
192.168.1.250/24).

You can also use the factory image with the nmrpflash tool.
For more information see https://github.com/jclehner/nmrpflash

Signed-off-by: David Bauer <mail@david-bauer.net>
[merge conflict in 02_network, flash@0 node rename, wlan DTS triggers]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:34:00 +00:00
Vladimir Kot
58becdb30d ramips: add support for ZyXEL Keenetic Start
Device specification:
- SoC: RT5350F
- CPU Frequency: 360 MHz
- Flash Chip: Winbond 25Q32 (4096 KiB)
- RAM: 32768 KiB
- 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
- 1x external, non-detachable antenna
- UART (J1) header on PCB (57800 8n1)
- Wireless: SoC-intergated: 2.4GHz 802.11bgn
- USB: None
- 3x LED, 2x button

Flash instruction:
1. Configure PC with static IP 192.168.1.2/24 and start TFTP server.
2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin"
   to "kstart_recovery.bin" and place it in TFTP server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power LED start blinking.
4. Router will download file from TFTP server, write it to flash and reboot.

Signed-off-by: Vladimir Kot <vova28rus@gmail.com>
[fixed git commit author and whitespace issues in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:34:00 +00:00
Tobias Welz
7c4b85ee27 ramips: add support for WIZnet WizFi630S board
The WIZnet WizFi630S board is in the miniPCIe form factor.

SoC: Mediatek MT7688AN
RAM: 128MB
Flash: 32Mb
WiFi: 2.4GHz
Ethernet: 3x 100Mbit
USB: 1 (USB 2.0)
serial ports: 2 (1x full, 1xlite)

Flash and recovery instructions: Use the factory installed u-boot boot
loader. It is available on UART2 (115200,8,n,1).  Then get the
sysupgrade image from a tftp server.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
[whitespace and device name in makefile fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:33:59 +00:00
Koen Vandeputte
af6c86dbe5 kernel: bump 4.14 to 4.14.108
Refreshed all patches.

Altered patches:
- 950-0033-i2c-bcm2835-Add-debug-support.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-27 10:48:59 +01:00
Felix Fietkau
bee7ff7cf3 ramips: allow packets with ttl=0
Some broken ISPs (e.g. Comcast) send DHCPv6 packets with hop limit=0.
This trips up the TTL=0 check in the PPE if enabled.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-03-24 12:10:15 +01:00
Pawel Dembicki
67fced9ba3 ramips: add support for DLINK DIR-510L
The DIR-510L Wireless Router are based on the MT7620A SoC.

Specification:

-MediaTek MT7620A (580 Mhz)
-128 MB of RAM
-16 MB of FLASH
-802.11bgn radio
-1x 10/100 Mbps Ethernet
-2x internal, non-detachable antennas
-UART (J3) header on PCB (57600 8n1)
-1x bi-color LED (GPIO-controlled), 2x button
-JBOOT bootloader

Known issues:
-Ethernet port is used as LAN
-No communication with charger IC. (uart bitbang needed)

Installation:
Apply factory image via d-link http web-gui.

How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
    curl -F FN=@XXXXX.bin http://192.168.123.254/upg
    where XXXXX.bin is name of firmware file.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed whitespace issue in 10-rt2x00-eeprom]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-24 01:44:24 +01:00
Pawel Dembicki
1f149fcad3 firmware-utils: mkdlinkfw: add kernel image offset
Some boards with JBOOT have partiton between bootloader
and kernel image. This patch add possibility to change kernel
partition start address.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-03-24 01:44:24 +01:00
Qin Wei
5f40b519f3 ramips: fix wrong i2s clock unit from kHz to MHz
clk_get_rate returns the current clock rate in Hz for a clock source so
if we divide it by 1M, then we get frequency in MHz and not kHz.

Signed-off-by: Qin Wei <support@vocore.io>
[added missing commit message, and fixed author with SoB from PR message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-24 01:44:24 +01:00
Adrian Schmutzler
4269914187 ramips: Speed up eeprom read/write
Reading and writing to and from flash storage is slowed down
enormously by some functions which use a block size of 1.

This patch reworks the extraction scripts to be much faster and
efficient by reading and writing in possibly one big block.

This is based on the initial commit a69e101 for ipq40xx by
Christian Lamparter <chunkeey@gmail.com>.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Rosen Penev <rosenp@gmail.com>
2019-03-21 00:57:54 +01:00
Ozgur Can Leonard
201d3d1a82 ramips: Xiaomi MIR3G: detect board name from DTS
- Former "mir3g" board name becomes "xiaomi,mir3g".
- Reorder some entries to maintain alphabetical order.
- Change DTS so status LEDs (yellow/red/blue) mimic
  Xiaomi stock firmware: (Section Indicator)
<http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf>
<http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf>
|Yellow: Update (LED flickering), the launch of the system (steady light);
|Blue: during normal operation (steady light);
|Red: Safe mode (display flicker), system failure (steady light);

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
[Added link to similar Router 3 model]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-21 00:57:54 +01:00
INAGAKI Hiroshi
5c11258297 ramips: add support for I-O DATA WN-AC733GR3
I-O DATA WN-AC733GR3 is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7620A.

Specification

- SoC		: MediaTek MT7620A
- RAM		: DDR2 64 MiB
- Flash		: SPI-NOR 8 MiB
- WLAN		: 2.4/5 GHz
  - 2.4 GHz : MT7620A (SoC), 2T2R
  - 5 GHz   : MT7610E, 1T1R
- Ethernet	: 10/100/1000 Mbps (RTL8367RB)
- LED/key	: 4x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J1: Vcc, RX, GND, TX from LED side
  - 57600n8

Flash instruction using factory image:

1. Boot WN-AC733GR3 normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-03-21 00:57:20 +01:00
Micke Prag
c3a17ee4b3 ramips: add #pwm-cells property to MT76x8 dts
To be able to configure pwms the pwm driver needs to know the number off
cells in the "pwms" property. For this platform this is 2.

Signed-off-by: Micke Prag <micke.prag@telldus.se>
2019-03-18 20:43:09 +01:00
Koen Vandeputte
a8cfef6c45 kernel: bump 4.14 to 4.14.106
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-18 10:02:51 +01:00
Chen Minqiang
7dfe357a3d ramips: HC5861 drop unused gpio group define in dts
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2019-03-13 16:25:34 +01:00
Ozgur Can Leonard
d009033911 ramips: add support for Xiaomi Mi Router 3 Pro
Hardware:

CPU:   MediaTek MT7621AT (2x880MHz)
RAM:   512MB DDR3
FLASH: 256MB NAND
WiFi:  2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!)
WiFI:  5GHz 4x4 MT7615 a/n/ac  (Needs driver, See Issues!)
USB:   1x 3.0
ETH:   1x WAN 10/100/1000 3x LAN 10/100/1000
LED:   Power/Status
BTN:   RESET
UART:  115200 8n1

Partition layout and boot:

Stock Xiaomi firmware has the MTD split into (among others)

- kernel0 (@0x200000)
- kernel1 (@0x600000)
- rootfs0
- rootfs1
- overlay (ubi)

Xiaomi uboot expects to find kernels at 0x200000 & 0x600000
referred to as system 1 & system 2 respectively.
a kernel is considered suitable for handing control over
if its linux magic number exists & uImage CRC are correct.
If either of those conditions fail, a matching sys'n'_fail flag
is set in uboot env & a restart performed in the hope that the
alternate kernel is okay.
If neither kernel checksums ok and both are marked failed, system 2
is booted anyway.

Note uboot's tftp flash install writes the transferred
image to both kernel partitions.

Installation:

Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in
kernel0 for ease of recovery, and install OpenWRT into kernel1 and
after.

The installation file for OpenWRT is a *squashfs-factory.bin file that
contains the kernel and a ubi partition. This is flashed as follows:

nvram set flag_try_sys1_failed=1
nvram set flag_try_sys2_failed=0
nvram commit
dd if=factory.bin bs=1M count=4 | mtd write - kernel1
dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0
reboot

Reverting to stock:

The part of stock firmware we've kept in kernel0 allows us to run stock
recovery, which will re-flash stock firmware from a *.bin file on a USB.

For this we do the following:

fw_setenv flag_try_sys1_failed 0
fw_setenv flag_try_sys2_failed 1
reboot

After reboot the LED status light will blink red, at which point pressing
the 'reset' button will cause stock firmware to be installed from USB.

Issues:

OpenWRT currently does not have support for the MT7615 wifi chips. There is
ongoing work to add mt7615 support to the open source mt76 driver. Until that
support is in place, there are closed-source kernel modules that can be used.

See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[02_network remaps, Added link to notes]
2019-03-13 16:25:34 +01:00
Piotr Dymacz
9b6413982c ramips: add support for ALFA Network Tube-E4G
ALFA Network Tube-E4G is an outdoor, dual-SIM LTE Cat. 4 CPE, based on
MediaTek MT7620A, equipped with Quectel EC25 miniPCIe modem.

Specification:

- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 1x detachable antenna (modem main)
- 1x internal antenna (modem div)
- 1x GPS passive antenna (optional)
- 5x LED (all driven by GPIO)
- 1x button (reset)
- UART (4-pin, 2.54 mm pitch) header on PCB

Other:

Default SIM slot is selected at an early stage by U-Boot, based on
'default_sim' environment value: 1 or unset = SIM1 (mini), 2 = SIM2
(micro). U-Boot also resets the modem, using #PERST signal, before
starting kernel.

Flash instruction:

You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:

1. Power the device with reset button pressed, the LAN LED will start
   blinking slowly and after ~3 seconds, when it starts blinking faster,
   you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-11 22:00:26 +01:00
Chen Minqiang
e15bda603a ramips: rework network settings for HC5861
dts: disable port4 and leave it ephy mode because it connect to nothing
switch port5 connected to GE port we use it as wan port

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2019-03-06 22:02:56 +01:00
Daniel Golle
c8778250a9 ramips: mt7620: export chip version and pkg
Similar to the (currently unused) mt7620_get_eco() function, introduce
mt7620_get_chipver() and mt7620_get_pkg() functions to allow rt2x00 to
probe for the type of WiSoC. This is ugly and probably unacceptable
for upstream, however, it should help to evaluate which of those hacks
are actually really needed, enumerate the possible values and label
them in a more meaningful way than currently done in the vendor driver.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-06 01:11:54 +01:00
Kip Porterfield
f2c83532f9 ramips: add support for Belkin F9K1109v1
Device specification:
- SoC: Ralink RT3883 (MIPS 74Kc) 500Mhz
- RAM: 64Mb
- Flash: 8MB (SPI-NOR)
- Ethernet: 10/100/1000 Mbps
- WLAN
	Wireless 1: SoC-integrated : 2.4/5 GHz
	Wireless 2: 2.4 GHz RT3092L
- LED: 2x USB, WAN, LAN
- Key: WPS, reset
- Serial: 4-pin header, (57600,8,N,1), 3.3V TTL,
	GND, RX, TX, V - J12 marking on board
- USB ports: 2 x USB 2.0

Flashing instructions:

Option 1 (from bootloader web)
- Hold reset button on the back of router when plugging
  in power (for at-least 10 seconds after plugged in)
- Connect to a Lan port
- Set computer IP to 10.10.10.3
- Go to http://10.10.10.123 in a web browser
- Click the Browse... Button and select the
   *squashfs.sysupgrade.bin file then click APPLY

Option 2 (from the stock admin web)
- Go to firmware upgrade
- Upload the **factory** image *initramfs.bin first
- Boot into openwrt
- From Luci web in openwrt upload the *squashfs.sysupgrade.bin

Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added v1 to the compatible identifier, added pciid for
the RT3092L, fixed pci unit-address, split out the F9K110X.dtsi
to prepare for a possible F9K1103 patch]
2019-03-02 13:04:45 +01:00
Marcel Jost
e6f047fa36 ramips: add TP-Link TL-WR802N-v4 support
This patch adds support for the TP-Link TL-WR802N-v4.
https://openwrt.org/toh/tp-link/tl-wr802n

Specification:
- MT7628N (580 MHz)
- 64 MB RAM
- 8 MB FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet
- 1x LED

Flash instruction:

The only way to flash the image in TL-WR802N v4 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 10 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Marcel Jost <majo@icutech.ch>
2019-02-28 11:26:10 +01:00
Thomas Vincent-Cross
a915ad8464 ramips: use generic board detection for Wavlink WL-WN575A3
Bring Wavlink WL-WN575A3 in line with other Wavlink ramips devices.

Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
2019-02-28 11:26:10 +01:00
Thomas Vincent-Cross
25c0b41901 ramips: various Wavlink WL-WN575A3 fixes
* assign pinmux groups to gpio function for LEDs/buttons
* rename flash node to be more generic in line with other device nodes
* remove useless/incorrect eeprom property from wmac node
* correct base mac address for embedded switch

Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
2019-02-28 11:26:10 +01:00