Commit Graph

23635 Commits

Author SHA1 Message Date
Piotr Dymacz
66abd58196 ath79: add support for ALFA Network AP121FE
The AP121FE is a slightly modified version of already supported AP121F
model (added to ar71xx in 0c6165d21a and to ath79 in 334bbc5198).

The differences in compare to AP121F:

- no micro SD card reader
- USB data lines are included in Type-A plug
- USB bus switched to device/peripheral mode (permanently, in bootstrap)

Other than that, specifications are the same:

- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz Wi-Fi, up to 15 dBm
- 1x IPEX/U.FL connector, internal PCB antenna
- 3x LED, 1x button, 1x switch
- 4-pin UART header on PCB (2 mm pitch)
- USB 2.0 Type-A plug (power and data)

Flash instruction (under U-Boot web recovery mode):

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
   wait for first blink of all LEDs (indicates network setup), then keep
   button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-09-28 01:28:37 +02:00
Piotr Dymacz
7f96cbd2a1 ath79: enable usbgadget feature
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-09-28 01:28:37 +02:00
Piotr Dymacz
b329bb9456 ath79: increase SPI clock and enable fast-read on AP121F
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-09-28 01:28:37 +02:00
Adrian Schmutzler
315904a459 ramips: merge ethernet setup for RT-AC51U/RT-AC54U
The ethernet setup/label MAC address for RT-AC51U and RT-AC54U are
the same, so move them into the shared DTSI.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-28 00:20:24 +02:00
Adrian Schmutzler
96023cd4ba ath79: fix LED labels for PowerCloud CAP324
The order of function and color in the labels in inverted for the
LAN LEDs. Fix it.

Fixes: 915966d861 ("ath79: Port PowerCloud Systems CAP324 support")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-27 15:58:14 +02:00
Adrian Schmutzler
d232a8ac7d ath79: fix rssi-low LED for My Net Range Extender
The LED color was missing in 01_leds.

Fixes: 745dee11ac ("ath79: add support for WD My Net Wi-Fi Range
Extender")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-27 15:58:14 +02:00
Sungbo Eo
4682d4d770 ipq40xx: tidy up device recipe for Edgecore OAP100
* split up DEVICE_TITLE into DEVICE_{VENDOR,MODEL}
* use SOC instead of DEVICE_DTS

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-09-26 18:26:19 +02:00
Adrian Schmutzler
621297e867 ramips: move dts-v1 statement to top-level DTSI files
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.

In ramips, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent mtxxxx/rtxxxx DTSI files already determines the DTS
version, so putting it into the DTS files is just a useless repetition.

Consequently, this patch puts the dts-v1 statement into the top-level
SoC-based DTSI files, and removes all other occurences.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes accordingly where necessary.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-25 23:26:40 +02:00
Adrian Schmutzler
41cc7edc15 ath79: move dts-v1 statement to ath79.dtsi
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.

In ath79, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent ath79.dtsi file already determines the DTS version, so
putting it into the DTS files is just a useless repetition.

Consequently, this patch puts the dts-v1 statement into the parent
ath79.dtsi, which is (indirectly) included by all DTS files. All
other occurences are removed.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes to make sure the ath79.dtsi or its
descendants are always included first.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-25 23:26:34 +02:00
Adrian Schmutzler
3ca2d31c54 ath79: move ath79-clk.h include to ath79.dtsi
ath79.dtsi uses ATH79_CLK_MDIO, so the include

  <dt-bindings/clock/ath79-clk.h>

needs to be moved there.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-25 23:24:09 +02:00
Adrian Schmutzler
bdd9dd8ab2 ipq40xx: tidy up dts-v1 statements
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.

Therefore, adding it to a DTS _and_ a DTSI file is actually wrong,
as it will be present twice then (though the compiler does not
complain about it).

In ipq40xx, the dts-v1 statement is already included in
qcom-ipq4019.dtsi, so we don't have to add it anywhere at all.
However, based on the conditions stated above, this requires
qcom-ipq4019.dtsi to be included as the first file in any DTS(I).

Consequently, this patch removes all cases of dts-v1 for the
ipq40xx target, and moves the includes accordingly where necessary.

While at it, remove a few obviously unneeded includes on the way.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-25 21:10:41 +02:00
Adrian Schmutzler
b284333b3a ath79: move engenius_loader_okli recipe before devices
Move engenius_loader_okli image recipe in front of all Engenius
devices, so adding new device entries will not have them sorted
before the shared recipe.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-25 20:07:16 +02:00
Linus Walleij
7e9e6fdac7 gemini: Bring up DSA switches
First group the interfaces on the DSA switch into the
right LAN/WAN groups. Tested successfully on the
D-Link DIR-685 with the RTL8366RB DSA switch.

The RTL8366RB is DSA custom tagged and now handled
by the kernel tag parser. (Backported.)

The Vitesse switches are not capable of supporting
DSA per-port tagging. We suspect they must be handled
using some custom VLAN set-up.

Cc: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[sorted devices alphabetically]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
fa1713e791 ipq40xx: fix DTS warning in qcom-ipq4029-gl-s1300.dts
.dts:226.17-230.4: Warning (spi_bus_reg): /soc/spi@78b6000/spi@1:
	SPI bus unit address format error, expected "0"

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
890bb54d7f ipq40xx: fix DTS warning in qcom-ipq4019-cm520-79f.dts
.dts:121.4-14: Warning (reg_format): /led_spi/led_gpio@0:reg: \
	property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
.dtb: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
.dtb: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
.dtb: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
.dts:119.24-126.5: Warning (avoid_default_addr_size): /led_spi/led_gpio@0: \
	Relying on default #size-cells value

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
0e4092cbad bcm53xx: add Cisco Meraki MR32
This patch adds support for Cisco Meraki MR32.
The unit was donated by Chris Blake. Thank you!

WARNING:
Only the 1x1:1 abgn Air Marshal WIPS wifi is currently supported by b43:
 b43-phy2: Found PHY: Analog 9, Type 4 (N), Revision 16
 b43-phy2: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1
 b43-phy2: Loading firmware version 784.2 (2012-08-15 21:35:19)
 and only as 802.11ABG!

while WIFI1 and WIFI2 (both BCM4352) are not:
 b43-phy0: Broadcom 4352 WLAN found (core revision 42)
 b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 12, Type 11 (AC), Revision 1)

Hardware Highlights:

SoC:	Broadcom BCM53016A1 (1 GHz, 2 cores)
RAM:	128 MiB
NAND:	128 MiB Spansion S34ML01G2 (~114 MiB useable)
ETH:	1GBit Ethernet Port - PoE
WIFI1:	Broadcom BCM43520 an+ac (2x2:2 - id: 0x4352)
WIFI2:	Broadcom BCM43520 bgn (2x2:2 - id: 0x4352)
WIFI3:	Broadcom BCM43428 abgn (1x1:1 - id: 43428)

BLE:	Broadcom BCM20732 (ttyS1)
LEDS:   1 x Programmable RGB Status LED (driven by a PWM)
	1 x White LED (GPIO)
	1 x Orange LED Fault Indicator (GPIO)
	2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON: one Reset button
MISC:   AT24C64 8KiB EEPROM (i2c - stores Ethernet MAC + Serial#!)
	ina219 hardware monitor (i2c)
	Kensington Lock

SERIAL:
	WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
	The Serial setting is 115200-8-N-1. The board has a populated
	right angle 1x4 0.1" pinheader.
	The pinout is: VCC, RX, TX, GND. (Use a multimeter)

Flashing needs a serial adaptor (due to the lack of a working dropbear on
the original firmware).

This flashing procedure for the MR32 was tested with firmware:
"r23-149867:150252-aacharya".

0. Create a seperate Ethernet LAN which does not have access to the internet.
   Ideally use 192.168.1.2 for your PC. Make sure to reserve 192.168.1.1 it
   will be used later on by the OpenWrt firmware. The original Meraki firmware
   will likely try to setup the network via DHCP Discovery, so make sure your
   PC is running a DHCP-Server (i.e.: dnsmasq)
   '# dnsmasq -i eth# -F 192.168.1.5,192.168.1.50
   Furthermore, the PC needs a supported ssh/http/ftp server in order to
   retrieve the initramfs + dtb file

1. Disassemble the MR32 device by removing all screws (4 screws are located
   under the 4 rubber feets!) and prying open the plastic covers without
   breaking the plastic retention clips. Once inside, remove all the screws
   on the outer metal shielding to get to the PCB. It's not necessary to
   remove the antennas!

2. Connect the serial cable to the serial header.

3. Partially reassemble the outer metal shielding to ensure that the SoC
   has a proper heat sink.

4. Connect the Ethernet patch cable to the device and the power cable.

5. Wait for the device to boot and enter the root shell.
   (rooting is not discussed in detail here please refer to
   Chris Blake - "pwning the meraki mr18" blog post:
   <https://servernetworktech.com/2016/02/pwning-the-meraki-mr18/>
   (The same method works with the MR32's r23-149867:150252-aacharya)

   Wait for the MR32 to enter the "<Meraki>" prompt and enter:
   <Meraki> odm serial_num read
   (Verify that it matches what's on the S/N Sticker on the back!)
   <Meraki> odm serial_num write Q2XX-XXXX-XXXV
   <Meraki> odm serial_num read
   (Verify that the S/N has changed - and the LED start to flash)

   now to flash the firmware:
   <Meraki> odm firmware part.safe "http://192.168.1.2/mr32-initramfs.bin"

Once OpenWrt booted use sysupgrade to permanently install
OpenWrt. To do this: Download the latest sysupgrade.bin file
for the MR32 to the device and use sysupgrade *sysupgrade.bin
to install it.

WARNING: DO NOT DELETE the "storage" ubi volume!

To flash later MR32 Firmwares like r25-201804051805-G885d6d78-dhow-rel
requires in-circut-i2c tools to access the I2C EEPROM AT24C64 next to
the SoC. The idea is pretty much the same as from Step 5 from above:
Change the serial number to Q2XXXXXXXXXV (should be around 0x7c), then
attach a serial cable, ethernet (but make sure the device can't reach
the internet!) hit "s" (the small s!) during boot to enter the root-shell
and add the following commands to the /storage/config there:

serial_allow_odm true
serial_access_enabled true
serial_access_check false
valid_config true

and then hit exit to let it finish booting.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
1291274335 kernel: package bcm53xx i2c module
The BCM5301x SoCs do have i2c. Since this is only
being used by the Meraki MR32, this will be packaged
as a module.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
abe46d5002 kernel: add default for new config symbols
Provide disabled defaults for I2C_SLAVE_EEPROM and IPMB_DEVICE_INTERFACE.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
5f610ec4b8 bcm53xx: backport uart2 and pcie2 device-nodes
These have made their way into -next. This patch
also includes the portion of the bcm53xx kernel
patch refreshes as the hunks in
302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch
moved slightly due to the added nodes.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
c6d9a2ac59 bcm53xx: enable PWM for bcm53xx
The Meraki MR32 (BCM53016A1) uses the pwm to drive the
tricolor LED. The driver has been available in upstream
for a long time. Only the Device-Tree definition was
missing, but it has been queued recently.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:33 +02:00
Hans Geiblinger
a9071d02b5 ipq40xx: Add support for Linksys MR8300 (Dallas)
The Linksys MR8300 is based on QCA4019 and QCA9888
and provides three, independent radios.
NAND provides two, alternate kernel/firmware images
with fail-over provided by the OEM U-Boot.

Hardware Highlights:

SoC: IPQ4019 at 717 MHz (4 CPUs)
RAM: 512MB RAM

SoC:	Qualcomm IPQ4019 at 717 MHz (4 CPUs)
RAM:	512M DDR3
FLASH:	256 MB NAND (Winbond W29N02GV, 8-bit parallel)
ETH:	Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks)
BTN:	Reset and WPS
USB:	USB3.0, single port on rear with LED
SERIAL:	Serial pads internal (unpopulated)
LED:	Four status lights on top + USB LED
WIFI1:	2x2:2 QCA4019 2.4 GHz radio on ch. 1-14
WIFI2:  2x2:2 QCA4019 5 GHz radio on ch. 36-64
WIFI3:  2x2:2 QCA9888 5 GHz radio on ch. 100-165

Support is based on the already supported EA8300.
Key differences:
	EA8300 has 256MB RAM where MR8300 has 512MB RAM.
	MR8300 has a revised top panel LED setup.

Installation:
"Factory" images may be installed directly through the OEM GUI using
URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1)

Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com>
[copied Hardware-highlights from EA8300. Fixed alphabetical order.
fixed commit subject, removed bogus unit-address of keys,
fixed author (used Signed-off-By to From:) ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:31:51 +02:00
Tomasz Maciej Nowak
e24635710c ipq40xx: add support for Luma Home WRTQ-329ACN
Luma Home WRTQ-329ACN, also known as Luma WiFi System, is a dual-band
wireless access point.

Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 2 MB SPI NOR
       128 MB SPI NAND
WIFI: 2.4 GHz 2T2R integrated
      5 GHz 2T2R integrated
Ethernet: 2x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
Bluetooth: 1x 4.0 CSR8510 A10, connected to USB bus
LEDS: 16x multicolor LEDs ring, controlled by MSP430G2403 MCU
Buttons: 1x GPIO controlled
EEPROM: 16 Kbit, compatible with AT24C16
UART: row of 4 holes marked on PCB as J19, starting count from the side
      of J19 marking on PCB
      1. GND, 2. RX, 3. TX, 4. 3.3V
      baud: 115200, parity: none, flow control: none

The device supports OTA or USB flash drive updates, unfotunately they
are signed. Until the signing key is known, the UART access is mandatory
for installation. The difficult part is disassembling the casing, there
are a lot of latches holding it together.

Teardown
Prepare three thin, but sturdy, prying tools. Place the device with back
of it facing upwards. Start with the wall having a small notch. Insert
first tool, until You'll feel resistance and keep it there. Repeat the
procedure for neighbouring walls. With applying a pressure, one edge of
the back cover should pop up. Now carefully slide one of the tools to
free the rest of the latches.
There's no need to solder pins to the UART holes, You can use hook clips,
but wiring them outside the casing, will ease debuging and recovery if
problems occur.

Installation
1. Prepare TFTP server with OpenWrt initramfs image.
2. Connect to UART port (don't connect the voltage pin).
3. Connect to LAN port.
4. Power on the device, carefully observe the console output and when
   asked quickly enter the failsafe mode.
5. Invoke 'mount_root'.
6. After the overlayfs is mounted run:
     fw_setenv bootdelay 3
   This will allow to access U-Boot shell.
7. Reboot the device and when prompted to stop autoboot, hit any key.
8. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
   'setenv' to do that, then run following commands:
     tftpboot 0x84000000 <openwrt_initramfs_image_name>
     bootm 0x84000000
   and wait till OpenWrt boots.
9. In OpenWrt command line run following commands:
     fw_setenv openwrt "setenv mtdids nand1=spi_nand; setenv mtdparts mtdparts=spi_nand:-(ubi); ubi part ubi; ubi read 0x84000000 kernel; bootm 0x84000000"
     fw_setenv bootcmd "run openwrt"
10. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
    with:
     ubirmvol /dev/ubi0 -N ubi_rootfs
     sysupgrade -v -n /tmp/<openwrt_sysupgrade_image_name>
11. After flashing, the access point will reboot to OpenWrt, then it's
    ready for configuration.

Reverting to OEM firmware
1. Execute installation guide steps: 1, 2, 3, 7, 8.
2. In OpenWrt command line run following commands:
     ubirmvol /dev/ubi0 -N rootfs_data
     ubirmvol /dev/ubi0 -N rootfs
     ubirmvol /dev/ubi0 -N kernel
     ubirename /dev/ubi0 kernel1 kernel ubi_rootfs1 ubi_rootfs
     ubimkvol /dev/ubi0 -S 34 -N kernel1
     ubimkvol /dev/ubi0 -S 320 -N ubi_rootfs1
     ubimkvol /dev/ubi0 -S 264 -N rootfs_data
     fw_setenv bootcmd bootipq
3. Reboot.

Known issues
The LEDs ring doesn't have any dedicated driver or application to control
it, the only available option atm is to manipulate it with 'i2cset'
command. The default action after applying power to device is spinning
blue light. This light will stay active at all time. To disable it
install 'i2c-tools' with opkg and run:
 i2cset -y 2 0x48 3 1 0 0 i
The light will stay off until next cold boot.

Additional information
After completing 5. step from installation guide, one can disable asking
for root password on OEM firmware by running:
 sed -e 's/root/root::/' -i /etc/passwd
This is useful for investigating the OEM firmware. One can look
at the communication between the stock firmware and the vendor's
cloud servers or as a way of making a backup of both flash chips.
The root password seems to be constant across all sold devices.
This is output of 'led_ctl' from OEM firmware to illustrate
possibilities of LEDs ring:

Usage: led_ctl [status | upgrade | force_upgrade | version]
       led_ctl solid    COLOR <brightness>
       led_ctl single   COLOR INDEX <brightness 0 - 15>
       led_ctl spinning COLOR <period 1 - 16 (lower = faster)>
       led_ctl fill     COLOR <period 1 - 16 (lower = faster)>
                                             ( default is 5 )
       led_ctl flashing COLOR <on dur 1 - 128>  <off dur 1 - 128>
                              (default is  34)  ( default is 34 )
       led_ctl pulsing  COLOR
COLOR: red, green, blue, yellow, purple, cyan, white

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[squash "ipq-wifi: add BDFs for Luma Home WRTQ-329ACN" into commit,
changed ubi volumes for easier integration, slightly reworded
commit message, changed ubi volume layout to use standard names all
around]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:30:19 +02:00
Brian Norris
03bc9b0002 ipq40xx: add open-drain support to pinctrl-msm
Submitted upstream. Shouldn't affect existing devices, but enables new
device support.

https://lore.kernel.org/linux-gpio/20200703080646.23233-1-computersforpeace@gmail.com/

Currently queued for-next:
https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl.git/commit/?h=for-next&id=13355ca35cd16f5024655ac06e228b3c199e52a9

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[refresh patch]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 18:43:09 +02:00
John Audia
3ea1b5b745 kernel: bump 5.4 to 5.4.67
All modifications made by update_kernel.sh

Build system: x86_64
Build-tested: ipq806x, lantiq/xrx200 and ath79/generic
Run-tested: ipq806x (R7800), lantiq (Easybox 904 xDSL)

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[add test on lantiq]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-24 18:53:23 +02:00
J. Scott Heppler
620f9c7734 ramips: add support for Linksys EA7300 v2
This submission relied heavily on the work of
Santiago Rodriguez-Papa <contact at rodsan.dev>

Specifications:

*  SoC:            MediaTek  MT7621A            (880  MHz  2c/4t)
*  RAM:            Winbond W632GG6MB-12         (256M  DDR3-1600)
*  Flash:          Winbond W29N01HVSINA         (128M  NAND)
*  Eth:            MediaTek  MT7621A            (10/100/1000  Mbps  x5)
*  Radio:          MT7603E/MT7615N              (2.4  GHz  &  5  GHz)
                     4  antennae:  1  internal  and  3  non-deatachable
*  USB:            3.0  (x1)
*  LEDs:
          White    (x1  logo)
          Green    (x6  eth  +  wps)
          Orange   (x5,  hardware-bound)
*  Buttons:
          Reset    (x1)
          WPS      (x1)

Installation:

Flash factory image through GUI.

This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.

Reverting to factory firmware:

Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.

Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
2020-09-23 12:17:32 +02:00
Adrian Schmutzler
0cfdc7d446 target: update SPDX license names
SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to
GPL-2.0-or-later. Reflect that in the SPDX license headers.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-22 20:58:26 +02:00
Paul Spooren
e8f61bf50d ath79: remove DTS from ATH79 target name
The legacy ar71xx target is removed and multiple targets use DTS now, so
there is no need to point that out for ATH79 specifically.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-09-22 20:29:24 +02:00
Chuanhong Guo
006cd489f0 mediatek: mt7622: select bluetooth module instead of firmware
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-09-22 21:13:54 +08:00
Chuanhong Guo
20f2bd044a mediatek: build btmtkuart as a kernel module
bluetooth on mt7622 needs a firmware to start. It can't be built-in or
it tries to load firmware before rootfs is mounted, and then fails.
build it as a kernel module to fix that.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-09-22 21:07:50 +08:00
David Woodhouse
7190fb2da4 mediatek: mt7623: use bash for generating bootable images
It turns out that 'echo -e' isn't portable; it doesn't work in the dash
builtin echo and Ubuntu users are complaining.

I can't even get octal (specified by POSIX) to work consistently because
those  variants of 'echo' which *do* support -e don't seem to interpret
octalwithout it.

I could switch to /bin/echo but using -e with that isn't actually
portable *either* even though it works today.

For now just stick with bash, and use its builtin. We may end up using
something else entirely; perhaps perl.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-09-19 13:39:29 +01:00
David Woodhouse
d10b738c4b mediatek: fix missing pause on switch port for Banana Pi R2
This causes rx drops when running iperf.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-09-19 13:39:29 +01:00
Adrian Schmutzler
95c9df7971 ipq806x: fix support of Edgecore ECW5410 support
This fixes several stylistic and functional errors of the recently
added Edgecore ECW5410:

  - fix call in 11-ath10k-caldata
  - use hex notation in 11-ath10k-caldata
  - remove redundant definitions from DTS that are already in DTSI
  - use proper sorting in image/Makefile
  - use DEVICE_VENDOR/DEVICE_MODEL instead of DEVICE_TITLE
  - use SOC instead of DEVICE_DTS

Fixes: 59f0a0fd83 ("ipq806x: add Edgecore ECW5410 support")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-19 13:32:11 +02:00
John Audia
770a9c6787 kernel: bump 5.4 to 5.4.66
All modifications made by update_kernel.sh/no manual intervention needed

Run-tested: ipq806x (R7800), ath79 (Archer C7v5), x86/64

No dmesg regressions, everything appears functional

Signed-off-by: John Audia <graysky@archlinux.us>
[add run test from PR]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-19 12:41:29 +02:00
John Thomson
bf2870c1d9 kernel: fix mtd partition erase < parent_erasesize writes
This bug applied where mtd partition end address,
or erase start address, was not cleanly divisible by parent mtd erasesize.

This error would cause the bits following the end of the partition
to the next erasesize block boundary to be erased,
and this partition-overflow data to be written to the partition erase
address (missing additional partition offset address)
of the mtd (top) parent device.

Fixes: FS#2428

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[shorten commit title, add Fixes, fix kernel 4.19 as well]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-19 12:41:29 +02:00
Roger Pueyo Centelles
e6b42386ba ath79/mikrotik: fix soft_config location for SXT 5n
The soft_config partition for these devices lays between 0xe000 and
0xf000 (as correctly detected by the RouterBoard platform driver),
before the bootloader2 partition which starts at 0x10000.

This commit correctly sorts the partitions, fixing the parsing error.

Fixes: FS#3314

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-09-17 23:52:03 +02:00
Martin Schiller
a594a5a330 lantiq: use uniform "u-boot-env" mtd label
This is the most popular choice in the linux kernel tree.

Within OpenWrt, this change will establish consistency with ath79
and ramips targets.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[extend commit message, include netgear_dm200, update base-files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-17 21:09:51 +02:00
Vladimir Vid
9f0d882680 mvebu: image: add check for fdt_add_r and kernel_addr_r variables
fdt_addr and kernel_addr variables are getting obsolete in the mainline
u-boot in favor of fdt_addr_r and kernel_addr_r.

By checking if the new variables exist, we can make sure that devices with newer
version of u-boot will work while not breaking support for the existing ones.

Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-09-17 21:09:51 +02:00
Felix Fietkau
4fb58813f9 mediatek: fix hardware flow offload
Add support for dealing with DSA ports

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-17 21:08:32 +02:00
David Bauer
056945faa4 ipq40xx: enable FRITZRepeater 3000 ports on switch
The ethernet ports on the AVM FRITZRepeater 3000 are not separated
between LAN and WAN in the stock firmware. OpenWrt currently abstracts
port 4 as eth0 and port 5 as eth1, bridging them in the kernel.

This patch adjusts the GMAC port bitmasks and default bitmask for ar40xx
to bridge them on the switch, avoiding traffic on both ports to pass
thru the CPU.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-17 18:08:46 +02:00
David Bauer
b7da0d2944 ath79: add support for Ubiquiti UniFi AP Pro
This adds support for the Ubiquiti UniFi AP Pro to the ath79 target. The
device was previously supported on the now removed ar71xx target.

SoC   Atheros AR9344
WiFi  Atheros AR9344 & Atheros AR9280
ETH   Atheros AR8327
RAM   128M DDR2
FLASH 16M SPI-NOR

Installation
------------

Follow the Ubiquiti TFTP recovery procedure for this device.

1. Hold down the reset button while connecting power for 10 seconds.
2. Transfer the factory image via TFTP to the AP (192.168.1.20)
3. Wait 2 minutes for the AP to write the firmware to flash. The device
   will automatically reboot to OpenWrt.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-17 18:07:39 +02:00
Adrian Schmutzler
6e170ffb96 ipq806x: sort entries in lib/upgrade/platform.sh
Apply alphabetic sorting like in the other files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-17 13:03:18 +02:00
Adrian Schmutzler
0b1cdb7eea treewide: remove empty default cases
There is no apparent reason to have an empty default case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-17 12:46:19 +02:00
Adrian Schmutzler
a744c14dfa ipq806x: sort entries in 02_network
Apply alphabetic sorting like in the other files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-17 12:33:45 +02:00
John Crispin
0fbdb51f76 ipq40xx: add Edgecore OAP-100 support
flashing the unit
* first update to latest edcore FW as per the PDF instructions
* boot the initramfs
  - tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm
* inside the initramfs call the following commiands
  - ubiattach -p /dev/mtd0
  - ubirmvol /dev/ubi0 -n0
  - ubirmvol /dev/ubi0 -n1
  - ubirmvol /dev/ubi0 -n2
* scp the sysupgrade image to the board and call
  - sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin

Signed-off-by: John Crispin <john@phrozen.org>
2020-09-17 08:43:07 +02:00
Robert Marko
4488b260a0 ipq40xx: add Edgecore ECW5211 support
This patch adds support for the Edgecore ECW5211 indoor AP.

Specification:
- SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7
- RAM: 256MB DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB MX35LFxGE4AB SPI-NAND
- Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn)
- CC2540 BLE connected to USB 2.0 port
- Atmel AT97SC3205T I2C TPM

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:43:03 +02:00
Robert Marko
59f0a0fd83 ipq806x: add Edgecore ECW5410 support
This patch adds support for the Edgecore ECW5410 indoor AP.

Specification:
- SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15
- RAM: 256MB(225 usable) DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB S34MS01G2 Parallel NAND
- Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn)
- CC2540 BLE
- UART console on RJ45 next to ethernet ports exposed.
Its Cisco pin compatible, 115200 8n1 baud.

Installation instructions:
Through stock firmware or initramfs.

1.Connect to console
2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe.
3. Transfer factory image
4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path>

This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0

Note

Initramfs:
1.  Connect to console
2.  Transfer the image from TFTP server with tftpboot,
or by using DHCP advertised image with dhcp command.
3. bootm
4. Run ubiformat /dev/mtd1

You need to interrupt the bootloader after rebooting and run:
run altbootcmd

This will switch your active rootfs partition to one you wrote to and boot from it.

So if rootfs1 is active, then it will change it to rootfs2.

This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0
If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those.
This will result in wrong ordering and OpenWrt will panic on boot.

5. Transfer sysupgrade image
6. Flash with sysupgrade -n.

Note that sysupgrade will write the image to rootfs partition that is not currently in use.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:42:17 +02:00
Robert Marko
43a53891ce ipq806x: import bootargs-append from IPQ40xx
This imports the patch that adds bootargs-append support from IPQ40xx.

This way we can append additional boot arguments from DTS instead of only being able to overwrite them.

This way dual firmware devices can use the rootfs number that bootloader passes to decide from what to boot.
But we still need to append console info and ubi root info.

This is used by Edgecore ECW5410.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:42:17 +02:00
Robert Marko
811af0d98a ipq806x: add GSBI1 node to DTSI
IPQ806x series also has a GSBI1 with UART and I2C peripherals, so lets add the node for it.

Its needed for Edgecore ECW5410 which uses the UART from GSBI1 as second UART for Bluetooth.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:42:17 +02:00
Robert Marko
6133ac8e99 ipq806x: 5.4: enable AT803X driver
Its needed for Edgecore ECW5410 which does not use QCA8337 switch,
but rather 2x AR8033 PHY-s directly connected to GMAC-s.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:42:17 +02:00
Aleksander Jan Bajkowski
4a46f36f99 lantiq: remove trailing whitespaces in dts
Remove trailing whitespaces in dts files.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-09-17 00:21:41 +02:00
Adrian Schmutzler
947bfc62d0 ath79: fix button types for WZR-HP-AG300H and WZR-600DHP
Router and Movie "keys" are actually switches for both devices
according to the manual. This has been properly implemented in ar71xx,
but overlooked when porting to ath79.

Fixes: 480bf28273 ("ath79: add support for Buffalo WZR-HP-AG300H")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-16 17:34:35 +02:00
Adrian Schmutzler
25f2f66eea ath79: add support for Buffalo WZR-600DHP
The hardware of this device seems to be identical to WZR-HP-AG300H.
It was already implemented as a clone in ar71xx.

Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM
- 32 MiB Flash
- WiFi 5 GHz a/n
- WiFi 2.4 GHz b/g/n
- 5x 1000Base-T Ethernet
- 1x USB 2.0

Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-16 17:32:12 +02:00
Adrian Schmutzler
c68105c3b4 ath79: use common device definition for Buffalo devices
The Buffalo devices in ath79 share their image generation code,
so let's create a shared Device definition for them.

Since most of them use BUFFALO_HWVER := 3, this is moved as
default to the shared definition as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-16 17:31:03 +02:00
Adrian Schmutzler
a99614a44f ath79: consistently use "info" label for default-mac partition
The tp-link safeloader devices typically contain a partition
"default-mac" which stores the MAC addresses. It is followed by other
partitions containing device info, like

  {"default-mac", 0x610000, 0x00020},
  {"pin", 0x610100, 0x00020},
  {"product-info", 0x611100, 0x01000},

In DTS, we typically assign a 0x10000 sized partition for these,
which is mostly labelled "mac" or "info". In rarer cases, the
partitions have been enclosed in a larger "tplink" or "config"
partition.

However, when comparing different devices, the implementation appears
relatively arbitrary at the moment.
Thus, this PR aims at harmonizing these partitions by always using
the name "info" for the DTS partition containing "default-mac".
"info" is preferred over "mac" as we never just have "default-mac"
alone, but always some other device-info partitions as well.

While at it, this also establishes a similar partitioning for the
few devices where the "info" partitions are part of a bigger
unspecific "config" partition or similar.

Besides the harmonization itself, this also allows to merge a few
cases in 11-ath10k-caldata.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-16 17:28:48 +02:00
Adrian Schmutzler
300173950d rtl838x: fix incorrect assignment from kstrtoul in serial.c
Assign return value of kstrtoul to error variable instead of
conversion value.

Suggested-by: Birger Koblitz <git@birger-koblitz.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-16 16:31:28 +02:00
Adrian Schmutzler
5c0cecb6c6 rtl838x: refresh config
Use "make kernel_oldconfig" to update and sort target config.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-16 16:31:28 +02:00
Adrian Schmutzler
0da0aab6f2 rtl838x: remove some debug output in rtl838x-nor.c
Seems like leftovers from development, remove them.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-16 16:31:28 +02:00
Adrian Schmutzler
d5c4750a71 rtl838x: remove and add some empty lines
Do some minor empty lines cleanup, i.e. remove those at EOF and
add some for cosmetic reasons/consistency.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-15 12:28:43 +02:00
Birger Koblitz
df8e6be59a rtl838x: add new architecture
This adds support for the RTL838x Architecture.
SoCs of this type are used in managed and un-managed Switches and Routers
with 8-28 ports. Drivers are provided for SoC initialization, GPIOs, Flash,
Ethernet including a DSA switch driver and internal and external PHYs used
with these switches.

Supported SoCs:

	RTL8380M
	RTL8381M
	RTL8382M

The kernel will also boot on the following RTL839x SoCs, however driver
support apart from spi-nor is missing:

	RTL8390
	RTL8391
	RTL8393

The following PHYs are supported:

	RTL8214FC (Quad QSGMII multiplexing GMAC and SFP port)
	RTL8218B internal: internal PHY of the RTL838x chips
	RTL8318b external (QSGMII 8-port GMAC phy)
	RTL8382M SerDes for 2 SFP ports
	Initialization sequences for the PHYs are provided in the form of
	firmware files.

Flash driver supports 3 / 4 byte access

DSA switch driver supports VLANs, port isolation, STP and port mirroring.

The ALLNET ALL-SG8208M is supported as Proof of Concept:

	RTL8382M SoC
	1 MIPS 4KEc core @ 500MHz
	8 Internal PHYs (RTL8218B)
	128MB DRAM (Nanya NT5TU128MB)
	16MB NOR Flash (MXIC 25L128)
	8 GBEthernet ports with one green status LED each (SoC controlled)
	1 Power LED (not configurable)
	1 SYS LED (configurable)
	1 On-Off switch (not configurable)
	1 Reset button at the right behind right air-vent (not configurable)
	1 Reset button on front panel (configurable)
	12V 1A barrel connector
	1 serial header with populated standard pin connector and with markings
	  GND TX RX Vcc(3.3V), connection properties: 115200 8N1

To install, upload the sysupgrade image to the OEM webpage.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2020-09-14 07:54:30 +02:00
Birger Koblitz
7bb1bd469e kernel: add support for ALLNET devices in mtdsplit
Add support for uimage headers from ALLNET and provide support for the
SG8208M and SG8310PM devices' magic bytes.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2020-09-14 07:54:30 +02:00
Adrian Schmutzler
a9790dff53 cns3xxx: drop target
This target has not been updated to 5.4 yet, and the only person
trying it (Koen) decided to retreat based on the following reasons:

- The target is not DT-aware at all

- The huge amount of effort required

- The SoC itself reached EoL at Cavium for some time now

- Upstream removed some important parts as it's also slowly getting EoL
  over there

- The commercial product that used this will fade out shortly

- The amount of download for this binary suggest that the target is not
  that popular

Since nobody has picked up the work since then, and this is the last
remaining 4.19-only target, finally drop it now.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-14 00:19:27 +02:00
Chuanhong Guo
2188ef954e ramips: mt7621: pbr-m1: fix firmware size
This board is equipped with Winbond W25Q256FV 32M SPI-NOR.
Fix partition size for that.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-09-13 19:15:06 +08:00
Chuanhong Guo
8126521e11 ramips: mt7621: pbr-m1: increase SPI clock to 50MHz
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-09-13 18:53:25 +08:00
Chuanhong Guo
6f2c95f0cf ramips: mt7621: pbr-m1: add pcie reset for asm1061
this board has a pcie to sata bridge connected to pcie2 with a
separated pcie reset on gpio7.
add reset-gpios and corresponding pinctrl nodes into dts.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-09-13 18:49:26 +08:00
Felix Fietkau
f0cc5f6c0a ramips/mediatek: improve GRO performance, fix PPE packet parsing
Backport upstream changes to initialize GDM settings and reset PPE
Allow GMAC to recognize the special tag to fix PPE packet parsing
Improve GRO performance by passing PPE L4 hash as skb hash

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-13 11:14:32 +02:00
John Audia
17e64b9447 kernel: bump 5.4 to 5.4.65
All modifications made by update_kernel.sh/no manual intervention needed

Build-tested: x86_64
Run-tested: ipq806x (R7800)

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2020-09-12 23:39:25 +02:00
Sander Vanheule
c9f51a9ad6 ath79: support for TP-Link EAP225-Wall v2
TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access
point. UART access and debricking require fine soldering.

The device was kindly provided for porting by Stijn Segers.

Device specifications:
* SoC: QCA9561 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (GD25Q127CSIG)
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (SoC): 4× 100Mbps
  * Eth0 (back): 802.3af/at PoE in
  * Eth1, Eth2 (bottom)
  * Eth3 (bottom): PoE out (can be toggled by GPIO)
* One status LED
* Two buttons (both work as failsafe)
  * LED button, implemented as KEY_BRIGHTNESS_TOGGLE
  * Reset button

Flashing instructions, requires recent firmware (tested on 1.20.0):
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface

Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
    * Bridge unpopulated resistors R162 (TXD) and R165 (RXD)
      Do NOT bridge R164
    * Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via sysupgrade or LuCI web interface

MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM ifconfig:
    br0       Link encap:Ethernet  HWaddr 50:...:04
    eth0      Link encap:Ethernet  HWaddr 50:...:04
    wifi0     Link encap:UNSPEC  HWaddr 50-...-04-...
    wifi1     Link encap:UNSPEC  HWaddr 50-...-05-...

Signed-off-by: Sander Vanheule <sander@svanheule.net>
[fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 19:37:24 +02:00
Zhong Jianxin
53df30f02b ath79: add support for Mercury MW4530R v1
Mercury MW4530R is a TP-Link TL-WDR4310 clone.

Specification:

* SOC: Atheros AR9344 (560 MHz)
* RAM: 128 MiB
* Flash: 8192 KiB
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327)
* Wireless:
  - 2.4 GHz b/g/n (internal)
  - 5 GHz a/n (AR9580)
* USB: yes, 1 x USB 2.0

Installation:

Flash factory image via OEM web interface.

Signed-off-by: Zhong Jianxin <azuwis@gmail.com>
2020-09-12 18:47:26 +02:00
John Audia
bee76f1bfa kernel: bump 5.4 to 5.4.64
Remove upstreamed patches:
 generic-backport
  701-v5.5-net-core-use-listified-Rx-for-GRO_NORMAL-in-napi_gro.patch

Manually merged:
 mediatek/patches-5.4
  0603-net-dsa-mt7530-Extend-device-data-ready-for-adding-a.patch

All other modifications made by update_kernel.sh

Build-tested: ipq806x, lantiq/xrx200, mvebu, x86/64
Run-tested: ipq806x (R7800), mvebu (mamba, rango),
  lantiq/xrx200 (Easybox 904 xDSL), x86/64

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[add community build/run tests to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 01:28:50 +02:00
Adrian Schmutzler
c4110a524e ramips: create common DTSI for Sunvalley Filehub devices
HooToo HT-TM05 and RAVPower RP-WD03 have almost identical hardware
(except for RAM size) and are from the same vendor (SunValley).

Create a common DTSI file for them.

Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 01:25:10 +02:00
Adrian Schmutzler
b56b499948 ramips: fix baud rate for RAVPower RP-WD03
The baud rate for the RAVPower RP-WD03 is 57600, not 115200.

Since this is the default from mt7620n.dtsi, the chosen node can
simply be removed from the device DTS.

Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")

Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 01:24:43 +02:00
Adrian Schmutzler
3fc7860961 ramips: assign LEDs for RAVPower RP-WD03
According to the User Manual, there is a "Wi-Fi LED" with blue and
green colors, doing the following by default:

  Flashing Blue: System loading
  Solid Blue: System loaded
  Flashing Green: Connecting to the Internet
  Solid Green: Connected to the Internet

According to this vendor behavior, we keep refer to the LED as "wifi"
but implement the according default behavior as in OEM firmware.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 01:24:30 +02:00
Adrian Schmutzler
77825f3cfe ramips: fix MAC address assignment for RAVPower RP-WD03
MAC assignment based on vendor firmware:

  2.4 GHz    *:b4   (factory 0x04)
  LAN/label  *:b4   (factory 0x28)
  WAN        *:b5   (factory 0x2e)

The previously used location 0x4000 for ethernet is actually empty.

Therefore, fix the ethernet MAC address and set it as label-mac-address.

Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")

Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 01:24:02 +02:00
Adrian Schmutzler
07aa858a73 ramips: fix partitions and boot for RAVPower RP-WD03
The RAVPower RP-WD03 is a battery powered router, with an Ethernet and
USB port. Due due a limitation in the vendor supplied U-Boot bootloader,
we cannot exceed a 1.5 MB kernel size, as is the case with recent builds
(i.e. post v19.07). This breaks both factory and sysupgrade images.

To address this, use the lzma loader (loader-okli) to work around this
limitation.

The improvements here also address the "misplaced" U-Boot environment
partition, which is located between the kernel and rootfs in the stock
image / implementation. This is addressed by making use of mtd-concat,
maximizing space available in the booted image.
This will make sysupgrade from earlier versions impossible.

Changes are based on the recently supported HooToo HT-TM05, as the
hardware is almost identical (except for RAM size) and is from the same
vendor (SunValley). While at it, also change the SPI frequency
accordingly.

Installation:

 - Download the needed OpenWrt install files, place them in the root
   of a clean TFTP server running on your computer. Rename the files as,
   - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel
   - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs
 - Plug the router into your computer via Ethernet
 - Set your computer to use 10.10.10.254 as its IP address
 - With your router shut down, hold down the power button until the first
   white LED lights up.
 - Push and hold the reset button and release the power button. Continue
   holding the reset button for 30 seconds or until it begins searching
   for files on your TFTP server, whichever comes first.
 - The router (10.10.10.128) will look for your computer at 10.10.10.254
   and install the two files. Once it has finished installation, it will
   automatically reboot and start up OpenWrt.
 - Set your computer to use DHCP for its IP address

Notes:

 - U-Boot environment can be modified, u-boot-env is preserved on initial
   install or sysupgrade
 - mtd-concat functionality is included, to leave a "hole" for u-boot-env,
   combining the OEM kernel and rootfs partitions

Most of the changes in this commit are the work of Russell Morris (as
credited below), I only wrapped them up and added compat-version.
Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader
to work!

Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")

Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-11 19:31:03 +02:00
Adrian Schmutzler
a4e5b8897a ramips: use proper name for RAVPower RP-WD03
The proper model name is RP-WD03 (i.e. with the RP- prefix).

Adjust all names to that.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-11 19:18:54 +02:00
Adrian Schmutzler
14024f6e0f kernel: use proper upstream inclusion version for patch
The patch is only included in kernel 5.5.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-11 18:40:44 +02:00
Adrian Schmutzler
4527f59428 ramips: move ravpower-wd009-factory recipe to mt76x8.mk
The recipe is only used for a single device, so put it in the
subtarget file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-11 18:40:44 +02:00
David Bauer
2e6c236abd ipq40xx: essedma: enable VLAN tag offload for single-port
Enable the VLAN tag offloading mechanism for RGMII single-port devices.
This allows those devices to use 802.1Q VLANs on the ethernet port.

Previously, RX frames were double tagged, as the RX TAG removal flag was
not enabled and an additional 802.1Q header was inserted elsewhere in
the code.

On the TX side, tagging was completely not present for single-port
devices. Enable tagging if an 802.1Q frame should be transmitted and
disable the default tagging mechanism for single-port devices.

Tested on Aruba AP-303

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-11 17:37:11 +02:00
Sergey Ryazanov
788aa61e1b ath25: fix preinit Ethernet port configuration
vconfig is no more installed by default to a firmware image. So, replace
vconfig calls for VLAN subinterface configuration by coresponding
ip-link commands.

Also drop few useless comments from the preinit hook script, while we
are at it.

I have no chance to test this fix since I have no board with a subject
switch IC, but this is still better then call an utility that is
unavailable in the firmware for years.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
[use documented syntax for ip link add]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-10 18:52:15 +02:00
Adrian Schmutzler
4d747f5495 kernel: add recently introduced CONFIG_MTD_SPLIT_ELF_FW
The config symbol was introduced in drivers, but not added to
generic kernel config files. This will halt build asking for the
value.

Fix it by adding the value (setting it to disabled).

Fixes: 3f7047db7a ("kernel: mtdsplit: support ELF loader splitting")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-09 22:09:19 +02:00
Sander Vanheule
9dd4ba3d7e ath79: add support for TP-Link EAP245-v3
TP-Link EAP245 v3 is an AC1750 (802.11ac Wave-2) ceiling mount access
point. UART access (for debricking) requires non-trivial soldering.

Specifications:
* SoC: QCA9563 (CPU/DDR/AHB @ 775/650/258 MHz)
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 3x3
* Wireless 5GHz (QCA9982): a/n/ac 3x3 with MU-MIMO
* Ethernet (QCA8337N switch): 2× 1GbE, ETH1 (802.3at PoE) and ETH2
* Green and amber status LEDs
* Reset switch (GPIO, available for failsafe)

Flashing instructions:
All recent firmware versions (latest is 2.20.0), can disable firmware
signature verification and use a padded firmware file to flash OpenWrt:
* ssh into target device and run `cliclientd stopcs`
* upload factory image via web interface

The stopcs-method is supported from firmware version 2.3.0. Earlier
versions need to be upgraded to a newer stock version before flashing
OpenWrt.

Factory images for these devices are RSA signed by TP-Link. While the
signature verification can be disabled, the factory image still needs to
have a (fake) 1024 bit signature added to pass file checks.

Debricking instructions:
You can recover using u-boot via the serial port:
* Serial port is available from J3 (1:TX, 2:RX, 3:GND, 4:3.3V)
* Bridge R237 to connect RX, located next to J3
* Bridge R225 to connect TX, located inside can on back-side of board
* Serial port is 115200 baud, 8n1, interrupt u-boot by holding ctrl+B
* Upload initramfs with tftp and upgrade via OpenWrt

Device mac addresses:
Stock firmware has the same mac address for 2.4GHz wireless and
ethernet, 5GHz is incremented by one. The base mac address is stored in
the 'default-mac' partition (offset 0x90000) at an offset of 8 bytes.
ART blobs contain no mac addresses.
From OEM ifconfig:
    ath0      Link encap:Ethernet  HWaddr 74:..:E2
    ath10     Link encap:Ethernet  HWaddr 74:..:E3
    br0       Link encap:Ethernet  HWaddr 74:..:E2
    eth0      Link encap:Ethernet  HWaddr 74:..:E2

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2020-09-09 20:42:10 +03:00
Sander Vanheule
b71668f96a ath79: enable elf mtd splitter
Enabled the ELF firmware partition splitter 4.19 and 5.4 in preparation
for the TP-Link EAP245v3 device support.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2020-09-09 20:41:50 +03:00
Sander Vanheule
3f7047db7a kernel: mtdsplit: support ELF loader splitting
To parse the ELF kernel loader, a small ELF parser is used that can
handle both ELF32 or ELF64 class loaders. The splitter assumes that the
kernel is always located before the rootfs, whether it is embedded in
the loader or not. If the kernel is located after the rootfs on the
firmware partition, then the rootfs splitter will include it in the
dynamically created rootfs_data partition and the kernel will be
corrupted.

The kernel image is preferably embedded inside the ELF loader, so the
end of the loader equals the end of the kernel partition. This is due to
the way mtd_find_rootfs_from searches for the the rootfs:
- if the kernel image is embedded in the loader, the appended rootfs may
  follow the loader immediately, within the same erase block.
- if the kernel image is not embedded in the loader, but placed at some
  offset behind the loader (OKLI-style loader), the rootfs must be
  aligned to an erase-block after the loader and kernel image.

In case section header table is empty, determine the elf loader size by
finding the end of the last segment, as defined by the program header
table.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2020-09-09 20:41:50 +03:00
Adrian Schmutzler
2dda301d40 ramips: disable default build for Ravpower RP-WD03
This device has a 1.5M kernel size limit during boot and is
unbootable since February 2019 [1].

[1] https://forum.openwrt.org/t/ravpower-wd03-does-not-start-with-openwrt-master/49792

Reported-by: Szabolcs Hubai <szab.hu@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-09 14:12:14 +02:00
Felix Fietkau
668c988fc5 mediatek/ramips: remove an ethernet optimization patch that was reported to cause a regression
In some tests, crashes were observed

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-09 11:51:47 +02:00
Felix Fietkau
c18a872825 mediatek: backport the latest version of the mt7531 support patches
Fixes unknown unicast flooding issue

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-09 11:51:47 +02:00
Adrian Schmutzler
38f6d5d217 treewide: revert sysupgrade adjustments for early DSA-adopters
The uci-default mechanism to update the compat-version was only
meant for early DSA-adopters, which should have updated by now.

Remove this workaround again in order to prevent the intended
experiences for all the other people.

This reverts:
a9703db720 ("mvebu: fix sysupgrade experience for early DSA-adopters")
86c89bf5e8 ("kirkwood: fix sysupgrade experience for early DSA-adopters")

Partially reverted:
1eac573b53 ("ramips: mt7621: implement compatibility version for DSA migration")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-08 19:27:15 +02:00
Adrian Schmutzler
de4e57eaaa Revert "treewide: add sysupgrade comment for early DSA-adopters"
This reverts commit e81e625ca3.

This was meant just for early DSA-adopters. Those should have
updated by now, remove it so future updaters get the intended
experience.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-08 19:26:22 +02:00
John Audia
2c2fcbd2e0 kernel: bump 5.4 to 5.4.63
Manually merged:
 hack-5.4
  230-openwrt_lzma_options.patch
 bcm27xx
  950-0283-hid-usb-Add-device-quirks-for-Freeway-Airmouse-T3-an.patch
 x86
  011-tune_lzma_options.patch

Remove upstreamed patches in collaboration with Ansuel Smith:
 ipq806x
  093-1-v5.8-ipq806x-PCI-qcom-Add-missing-ipq806x-clocks-in-PCIe-driver.patch
  093-2-v5.8-ipq806x-PCI-qcom-Change-duplicate-PCI-reset-to-phy-reset.patch
  093-3-v5.8-ipq806x-PCI-qcom-Add-missing-reset-for-ipq806x.patch

All other modifications made by update_kernel.sh

Build-tested: bcm27xx/bcm2708, ipq806x, x86/64
Run-tested: ipq806x (R7800), x86/64

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[update commit message/tested]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-06 19:55:19 +02:00
Adrian Schmutzler
ad22f6a8aa ath25: disable devices with 4M flash
Devices with 4M flash are not built be default for 20.xx anymore.

Building them with buildbot settings does not work anymore anyway.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-06 19:50:36 +02:00
Adrian Schmutzler
9c12a33b24 ath25: apply vendor_model scheme
This applies the vendor_model scheme for this target as well, so
naming is consistent throughout supported targets.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-06 19:49:53 +02:00
Sergey Ryazanov
ce3b135243 ath25: eth: fix crash on skb DMA (un-)map
AR2315 Ethernet driver pass NULL instead of a real device pointer to DMA
(un-)map calls. With kernel version 5.4 such behaviour causes a kernel
panic. Fix this issue by preserving device pointer during the probe
procedure and pass it to each skb data DMA (un-)map call.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2020-09-06 19:49:43 +02:00
Sergey Ryazanov
36e06497f4 ath25: fix ethernet supported link modes for ar2313
Rework ethernet supported link modes to linkmode bitmask.

This is needed to suppress compilation errors:

   drivers/net/ethernet/atheros/ar231x/ar231x.c:1153:20: ...
     error: assignment to expression with array type
     phydev->supported &= (SUPPORTED_10baseT_Half
                       ^~

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
[cut out of bigger patch, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-06 19:49:37 +02:00
Adrian Schmutzler
1a4c1d64bc ath25: fix compilation for AR2315 MTD driver
Kernel commit e7bfb3fdbde3 ("mtd: Stop updating erase_info->state
and calling mtd_erase_callback()") removed erase_info->state
updates and calls of mtd_erase_callback().

Drop these erase callback invocations from AR2315 MTD driver as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-06 19:49:28 +02:00
Adrian Schmutzler
481d0281d8 ath25: update config for kernel 5.4
Update config with make kernel_oldconfig.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-06 19:49:19 +02:00
Adrian Schmutzler
fc920bfb00 ath25: refresh patches for kernel 5.4
Refresh patches to make them apply to kernel 5.4.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-06 19:49:13 +02:00
Adrian Schmutzler
081e944be6 ath25: add back target support
Discussion on the mailing list reveals that this target has active
users. As we are finally able to upgrade this target to kernel 5.4,
add it back to master.

This reverts commit 7d29a55714 ("ath25: drop target") and
immediately moves the relevant files to 5.4, without touching
the content.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-06 19:49:05 +02:00
Adrian Schmutzler
8938711223 ath79: drop Build/loader-kernel-cmdline
This is the same as  loader-kernel since the KERNEL_CMDLINE
parameter has been removed in [1] and not used at all anyway.

Remove it.

[1] f77db1a590 ("ath79: cleanup image build code")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2020-09-06 19:43:08 +02:00
Josh Bendavid
b5dd746cbb ramips: add support for D-Link DIR-2660 A1
This patch adds support for D-Link DIR-2660 A1.

Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
        WiFi 5G (white), USB 3.0 (white), USB 2.0 (white)

Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips

Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
  button, then re-plug it. Keep the reset button pressed until the power
  LED starts flashing orange, manually assign a static IP address under
  the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1

* Some modern browsers may have problems flashing via the Recovery GUI,
  if that occurs consider uploading the firmware through cURL:

    curl -v -i -F "firmware=@file.bin" 192.168.0.1

MAC addresses:

lan   factory 0xe000     *:a7 (label)
wan   factory 0xe006     *:aa
2.4   factory 0xe000 +1  *:a8
5.0   factory 0xe000 +2  *:a9

Seems like vendor didn't replace the dummy entries in the calibration data.

Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[rebase onto already merged DIR-1960 A1, add MAC addresses to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-06 19:09:45 +02:00
Felix Fietkau
ba72ed537c kernel: backport GRO improvements
Improves network performance

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-06 15:35:57 +02:00
Felix Fietkau
63b6b10670 kernel: backport improved checksum function for ARM64
Improves network performance in some cases when checksum offload is not
available

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-06 15:35:57 +02:00
Felix Fietkau
21ab979c70 mediatek/mt7622: adjust kernel cpu features to match the hardware
Disable unnecessary errata/features
Enable potentially needed ones

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-06 15:35:57 +02:00
Christian Lamparter
252197f014 apm821xx: provide legacy interrupts for PCIe in DT
Devices with PCIe-Switches like the WNDR4700, MR24 and WNDAP660
need to have the interrupts property specified in the device-tree
for the legacy pci interrupt signaling method to work.

If the proper interrupt value is not specified, the default INTA
IRQ 12 is taken for all devices. This is especially bad, if the
device is setup to use INTC, because these interrupts will not
be serviced.

Russell Senior reported his experience on the MR24:
"The symptom is client devices can't see the beacons.
Wifi ifaces appear, can scan and hear other networks,
but clients can't see the MR24's SSIDs."

(The interrupts-property on the WNDAP620 was optional since it
uses INTA by default. Likewise the MX60W is in the same category)

Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-05 23:26:05 +02:00
Felix Fietkau
920d975cab mediatek: enable coherent DMA for ethernet and PCI
Improves performance by eliminating the need for extra cache flushes

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-04 19:42:35 +02:00
Felix Fietkau
44fe9e6f84 mediatek: fix an irq handling issue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-04 19:42:35 +02:00
Felix Fietkau
7081b1704e mediatek/ramips: add patch to avoid unnecessary rearming of interrupts
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-04 19:42:35 +02:00
Felix Fietkau
1fe914d9b4 mediatek: disable packet steering by default
mt76 now spreads the load over multiple CPUs more smoothly, processing
ethernet packets should be faster running on one core

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-04 19:42:35 +02:00
Felix Fietkau
a38b6efbc1 mediatek: enable kernel PCIe ASPM support, refresh kernel config
Improves performance on PCIe devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-04 12:42:46 +02:00
Yangbo Lu
ad0f0df909 layerscape: fix linux headers install issue
The linux upstream commit had treated config leak as error.
5967577 scripts: headers_install: Exit with error on config leak

It is causing below build issue. Provide a kernel patch to fix
it by replacing CONFIG_COMPAT kernel option with FM_COMPAT instead.

  HDRINST usr/include/linux/fmd/integrations/integration_ioctls.h
  HDRINST usr/include/linux/fmd/Peripherals/fm_port_ioctls.h
error: include/uapi/linux/fmd/Peripherals/fm_port_ioctls.h: leak
CONFIG_COMPAT to user-space
scripts/Makefile.headersinst:63: recipe for target
'usr/include/linux/fmd/Peripherals/fm_port_ioctls.h' failed
make[5]: *** [usr/include/linux/fmd/Peripherals/fm_port_ioctls.h] Error 1
Makefile:1198: recipe for target 'headers' failed
make[4]: *** [headers] Error 2

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-09-03 14:34:33 +01:00
Russell Morris
45a81f7056 ramips: add support for HooToo HT-TM05
The HooToo HT-TM05 is a battery powered router, with an Ethernet and USB port.
Vendor U-Boot limited to 1.5 MB kernel size, so use lzma loader (loader-okli).

Specifications:

  SOC:     MediaTek MT7620N
  BATTERY: 10400mAh
  WLAN:    802.11bgn
  LAN:     1x 10/100 Mbps Ethernet
  USB:     1x USB 2.0 (Type-A)
  RAM:     64 MB
  FLASH:   GigaDevice GD25Q64, Serial 8 MB Flash, clocked at 50 MHz
           Flash itself specified to 80 MHz, but speed limited by mt7620 SPI
           fast-read enabled (m25p)
  LED:     Status LED (blue after boot, green with WiFi traffic
           4 leds to indicate power level of the battery (unable to control)
  INPUT:   Power, reset button

MAC assignment based on vendor firmware:

  2.4 GHz    *:b4   (factory 0x04)
  LAN/label  *:b4   (factory 0x28)
  WAN        *:b5   (factory 0x2e)

Tested and working:

 - Ethernet
 - 2.4 GHz WiFi (Correct MAC-address)
 - Installation from TFTP (recovery)
 - OpenWRT sysupgrade (Preserving and non-preserving), through the usual
   ways: command line and LuCI
 - LEDs (except as noted above)
 - Button (reset)
 - I2C, which is needed for reading battery charge status and level
 - U-Boot environment / variables (from U-Boot, and OpenWrt)

Installation:

 - Download the needed OpenWrt install files, place them in the root
   of a clean TFTP server running on your computer. Rename the files as,
   - ramips-mt7620-hootoo_tm05-squashfs-kernel.bin => kernel
   - ramips-mt7620-hootoo_tm05-squashfs-rootfs.bin => rootfs
 - Plug the router into your computer via Ethernet
 - Set your computer to use 10.10.10.254 as its IP address
 - With your router shut down, hold down the power button until the first
   white LED lights up.
 - Push and hold the reset button and release the power button. Continue
   holding the reset button for 30 seconds or until it begins searching
   for files on your TFTP server, whichever comes first.
 - The router (10.10.10.128) will look for your computer at 10.10.10.254
   and install the two files. Once it has finished installation, it will
   automatically reboot and start up OpenWrt.
 - Set your computer to use DHCP for its IP address

Notes:

 - U-Boot environment can be modified, u-boot-env is preserved on initial
   install or sysupgrade
 - mtd-concat functionality is included, to leave a "hole" for u-boot-env,
   combining the OEM kernel and rootfs partitions

I would like to thank @mpratt14 and @xabolcs for their help getting the
lzma loader to work!

Signed-off-by: Russell Morris <rmorris@rkmorris.us>
[drop changes in image/Makefile, fix indent and PKG_RELEASE in
uboot-envtools, fix LOADER_FLASH_OFFS, minor commit message facelift,
add COMPILE to Device/Default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-03 14:15:30 +02:00
Chuanhong Guo
b7013e9c4a ramips: image: add recipe for OKLI loader
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-09-03 14:15:30 +02:00
Chuanhong Guo
cac9e3e2cb ramips: lzma-loader: make FLASH_START configurable
FLASH_START is supposed to point at the memory area where NOR flash are
mapped. We currently have an incorrect FLASH_START copied from ar71xx
back then and the loader doesn't work under OKLI mode.
On ramips, mt7621 has it's flash mapped to 0x1fc00000 and other SoCs
uses 0x1c000000. This commit makes FLASH_START a configurable value to
handle both cases.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-09-03 14:15:30 +02:00
Adrian Schmutzler
95acc4fe0e kernel: remove support for kernel 4.14
No target uses kernel 4.14 anymore.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-02 16:29:23 +02:00
Adrian Schmutzler
66ab1fb395 ramips: drop support for kernel 4.14
The target seems to be working on 5.4, so drop 4.14 support in
preparation for removing it from master entirely.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-02 16:29:23 +02:00
Adrian Schmutzler
e68c017e93 pistachio: drop support for kernel 4.14
The target seems to be working on 5.4, so drop 4.14 support in
preparation for removing it from master entirely.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-02 16:29:22 +02:00
Adrian Schmutzler
64824db6d8 arc770: drop support for kernel 4.14
The target seems to be working on 5.4, so drop 4.14 support in
preparation for removing it from master entirely.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-02 16:29:22 +02:00
Adrian Schmutzler
bc88ee0aff samsung: drop target
This target is still on kernel 4.14, and no attempt has been made to
update it to a newer kernel. Since we already are two LTS versions ahead
of that the target is dropped, as the chance of somebody bumping it will
only decrease with time.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-02 16:29:22 +02:00
Adrian Schmutzler
94198e2a1c rb532: drop target
This target is still on kernel 4.14, and recent attempts to move it to
kernel 5.4 have not led to success. The device tester reported that it
wouldn't boot with the following messages:

From sysupgrade:

  Press any key within 4 seconds to enter setup....
  loading kernel from nand... OK
  setting up elf image... OK
  jumping to kernel code

At this point the system hangs.

From CompactFlash:

  Press any key within 4 seconds to enter setup....
  Booting CF
  Loading kernel... done
  setting up elf image... kernel out of range kernel loading failed

The tester reported that the same was observed with current master
(kernel 4.14) as well. This looks like some kernel size restriction.

Since this target is quite old and only supports one device, and since
nobody else seemed interested in working on this for quite some time,
I decided to not put further work into analyzing the problem and drop
this together with the other 4.14-only targets.

Patchwork series:
https://patchwork.ozlabs.org/project/openwrt/list/?series=197066&state=*

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-02 16:29:22 +02:00
Adrian Schmutzler
7d29a55714 ath25: drop target
This target still only works with kernel 4.14, and not so recent
attempts of getting newer kernel versions supported did not lead
to success. Therefore, drop the target, as we are already two
LTS kernel versions ahead and it does not seem like anybody will
pick up the work.

Patchwork series:
https://patchwork.ozlabs.org/project/openwrt/list/?series=169991&state=*

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-02 16:29:22 +02:00
Felix Fietkau
b5d425af23 mediatek/ramips: unify ethernet driver fixes and add performance optimizations
Increase DMA burst size and tx ring size and optimize tx processing

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-01 17:01:56 +02:00
John Crispin
4841ac042e mediatek: pull in some fixes fromt he latest SDK
Signed-off-by: John Crispin <john@phrozen.org>
2020-09-01 09:09:13 +02:00
Michael Pratt
22caf30a65 ath79: add support for Senao Engenius ENH202 v1
FCC ID: U2M-ENH200

Engenius ENH202 is an outdoor wireless access point with 2 10/100 ports,
built-in ethernet switch, internal antenna plates and proprietery PoE.

Specification:

  - Qualcomm/Atheros AR7240 rev 2
  - 40 MHz reference clock
  - 8 MB FLASH                  ST25P64V6P (aka ST M25P64)
  - 32 MB RAM
  - UART at J3                  (populated)
  - 2x 10/100 Mbps Ethernet     (built-in switch at gmac1)
  - 2.4 GHz, 2x2, 29dBm         (Atheros AR9280 rev 2)
  - internal antenna plates     (10 dbi, semi-directional)
  - 5 LEDs, 1 button            (LAN, WAN, RSSI) (Reset)

Known Issues:

  - Sysupgrade from ar71xx no longer possible
  - Power LED not controllable, or unknown gpio

MAC addresses:

  eth0/eth1  *:11   art 0x0/0x6
  wlan       *:10   art 0x120c

  The device label lists both addresses, WLAN MAC and ETH MAC,
  in that order.

  Since 0x0 and 0x6 have the same content, it cannot be
  determined which is eth0 and eth1, so we chose 0x0 for both.

Installation:

  2 ways to flash factory.bin from OEM:

  - Connect ethernet directly to board (the non POE port)
      this is LAN for all images
  - if you get Failsafe Mode from failed flash:
      only use it to flash Original firmware from Engenius
      or risk kernel loop or halt which requires serial cable

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    In upper right select Reset
    "Restore to factory default settings"
    Wait for reboot and login again
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt boot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9f670000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

Return to OEM:

  If you have a serial cable, see Serial Failsafe instructions

  *DISCLAIMER*
  The Failsafe image is unique to Engenius boards.
  If the failsafe image is missing or damaged this will not work
  DO NOT downgrade to ar71xx this way, can cause kernel loop or halt

  The easiest way to return to the OEM software is the Failsafe image
  If you dont have a serial cable, you can ssh into openwrt and run

  `mtd -r erase fakeroot`

  Wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

Format of OEM firmware image:

  The OEM software of ENH202 is a heavily modified version
  of Openwrt Kamikaze bleeding-edge. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-senao-enh202-uImage-lzma.bin
    openwrt-senao-enh202-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring, and by swapping headers to see
  what the OEM upgrade utility accepts and rejects.

  OKLI kernel loader is required because the OEM firmware
  expects the kernel to be no greater than 1024k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on built-in switch:

  ENH202 is originally configured to be an access point,
  but with two ethernet ports, both WAN and LAN is possible.

  the POE port is gmac0 which is preferred to be
  the port for WAN because it gives link status
  where swconfig does not.

Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[assign label_mac in 02_network, use ucidef_set_interface_wan,
use common device definition, some reordering]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-31 17:41:21 +02:00
Michael Pratt
6decbf3186 ath79: add support for Senao Engenius ENS202EXT v1
Engenius ENS202EXT v1 is an outdoor wireless access point with 2 10/100 ports,
with built-in ethernet switch, detachable antennas and proprietery PoE.

FCC ID:	A8J-ENS202

Specification:

  - Qualcomm/Atheros AR9341 v1
  - 535/400/200/40 MHz          (CPU/DDR/AHB/REF)
  - 64 MB of RAM
  - 16 MB of FLASH              MX25L12835F(MI-10G)
  - UART (J1) header on PCB     (unpopulated)
  - 2x 10/100 Mbps Ethernet     (built-in switch Atheros AR8229)
  - 2.4 GHz, up to 27dBm        (Atheros AR9340)
  - 2x external, detachable antennas
  - 7x LED (5 programmable in ath79), 1x GPIO button (Reset)

Known Issues:

  - Sysupgrade from ar71xx no longer possible
  - Ethernet LEDs stay on solid when connected, not programmable

MAC addresses:

  eth0/eth1  *:7b   art 0x0/0x6
  wlan       *:7a   art 0x1002

  The device label lists both addresses, WLAN MAC and ETH MAC,
  in that order.

  Since 0x0 and 0x6 have the same content, it cannot be
  determined which is eth0 and eth1, so we chose 0x0 for both.

Installation:

  2 ways to flash factory.bin from OEM:

  - Connect ethernet directly to board (the non POE port)
      this is LAN for all images
  - if you get Failsafe Mode from failed flash:
      only use it to flash Original firmware from Engenius
      or risk kernel loop which requires serial cable

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    In upper right select Reset
    "Restore to factory default settings"
    Wait for reboot and login again
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt boot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fdf0000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

  *If you are unable to get network/LuCI after flashing*
  You must perform another factory reset:

    After waiting 3 minutes or when Power LED stop blinking:

    Hold Reset button for 15 seconds while powered on
    or until Power LED blinks very fast

    release and wait 2 minutes

Return to OEM:

  If you have a serial cable, see Serial Failsafe instructions

  *DISCLAIMER*
  The Failsafe image is unique to this model.
  The following directions are unique to this model.
  DO NOT downgrade to ar71xx this way, can cause kernel loop

  The easiest way to return to the OEM software is the Failsafe image
  If you dont have a serial cable, you can ssh into openwrt and run

  `mtd -r erase fakeroot`

  Wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

TFTP Recovery:

  For some reason, TFTP is not reliable on this board.
  Takes many attempts, many timeouts before it fully transfers.

  Starting with an initramfs.bin:

  Connect to ethernet
  set IP address and TFTP server to 192.168.1.101
  set up infinite ping to 192.168.1.1
  rename the initramfs.bin to "vmlinux-art-ramdisk" and host on TFTP server
  disconnect power to the board
  hold reset button while powering on board for 8 seconds

  Wait a minute, power LED should blink eventually if successful
  and a minute after that the pings should get replies
  You have now loaded a temporary Openwrt with default settings temporarily.
  You can use that image to sysupgrade another image to overwrite flash.

Format of OEM firmware image:

  The OEM software of ENS202EXT is a heavily modified version
  of Openwrt Kamikaze bleeding-edge. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-senao-ens202ext-uImage-lzma.bin
    openwrt-senao-ens202ext-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring, and by swapping headers to see
  what the OEM upgrade utility accepts and rejects.

Note on the factory.bin:

  The newest kernel is too large to be in the kernel partition

  the new ath79 kernel is beyond   1592k
  Even ath79-tiny is               1580k

  Checksum fails at boot because the bootloader (modified uboot)
  expects kernel to be 1536k. If the kernel is larger, it gets
  overwritten when rootfs is flashed, causing a broken image.
  The mtdparts variable is part of the build and saving a new
  uboot environment will not persist after flashing.
  OEM version might interact with uboot or with the custom
  OEM partition at 0x9f050000.

  Failed checksums at boot cause failsafe image to launch,
  allowing any image to be flashed again.

  HOWEVER: one should not install older Openwrt from failsafe
  because it can cause rootfs to be unmountable,
  causing kernel loop after successful checksum.
  The only way to rescue after that is with a serial cable.

  For these reasons, a fake kernel (OKLI kernel loader)
  and fake squashfs rootfs is implemented to take care of
  the OEM firmware image verification and checksums at boot.
  The OEM only verifies the checksum of the first image
  of each partition respectively, which is the loader
  and the fake squashfs. This completely frees
  the "firmware" partition from all checks.

  virtual_flash is implemented to make use of the wasted space.
  this leaves only 2 erase blocks actually wasted.

  The loader and fakeroot partitions must remain intact, otherwise
  the next boot will fail, redirecting to the Failsafe image.

  Because the partition table required is so different
  than the OEM partition table and ar71xx partition table,
  sysupgrades are not possible until one switches to ath79 kernel.

Note on sysupgrade.tgz:

  To make things even more complicated, another change is needed to
  fix an issue where network does not work after flashing from either
  OEM software or Failsafe image, which implants the OEM (Openwrt Kamikaze)
  configuration into the jffs2 /overlay when writing rootfs from factory.bin.

  The upgrade script has this:

    mtd -j "/tmp/_sys/sysupgrade.tgz" write "${rootfs}" "rootfs"

  However, it also accepts scripts before and after:

    before_local="/etc/before-upgradelocal.sh"
    after_local="/etc/after-upgradelocal.sh"
    before="before-upgrade.sh"
    after="after-upgrade.sh"

  Thus, we can solve the issue by making the .tgz an empty file
  by making a before-upgrade.sh in the factory.bin

Note on built-in switch:

  There is two ports on the board, POE through the power supply brick,
  the other is on the board. For whatever reason, in the ar71xx target,
  both ports were on the built-in switch on eth1. In order to make use
  of a port for WAN or a different LAN, one has to set up VLANs.

  In ath79, eth0 and eth1 is defined in the DTS so that the
  built-in switch is seen as eth0, but only for 1 port
  the other port is on eth1 without a built-in switch.

  eth0: switch0
    CPU is port 0
    board port is port 1

  eth1: POE port on the power brick

  Since there is two physical ports,
  it can be configured as a full router,
  with LAN for both wired and wireless.

  According to the Datasheet, the port that is not on the switch
  is connected to gmac0. It is preferred that gmac0 is chosen as WAN
  over a port on an internal switch, so that link status can pass
  to the kernel immediately which is more important for WAN connections.

Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[apply sorting in 01_leds, make factory recipe more generic, create common
device node, move label-mac to 02_network, add MAC addresses to commit
message, remove kmod-leds-gpio, use gzip directly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-31 17:41:21 +02:00
Roger Pueyo Centelles
781d4bfb39 ath79: mikrotik: fix network setup for lhg-hb platform
This network setup for MikroTik devices based on the LHG-HB platform
avoids using the integrated switch and connects the single Ethernet
port directly. This way, link speed (10/100 Mbps) is properly repor-
ted by eth0.

Fixes: FS#3309

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-08-31 17:41:21 +02:00
Sven Wegener
0348a02c7c ath79: use correct MAC address for TP-Link TL-WPA8630 v2
The base address is used for the LAN and 2G WLAN interfaces.
5G WLAN interface is +1 and the PLC interface uses +2.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
[improve commit title, fix assignment in 11-ath10k-caldata]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-31 17:41:21 +02:00
Martin Kennedy
af9dee336d ath79: add support for Meraki MR16
Port device support for Meraki MR16 from the ar71xx target to ath79.

Specifications:

  * AR7161 CPU, 16 MiB Flash, 64 MiB RAM
  * One PoE-capable Gigabit Ethernet Port
  * AR9220 / AR9223 (2x2 11an / 11n) WLAN

Installation:

  * Requires TFTP server at 192.168.1.101, w/ initramfs & sysupgrade .bins
  * Open shell case and connect a USB to TTL cable to upper serial headers
  * Power on the router; connect to U-boot over 115200-baud connection
  * Interrupt U-boot process to boot Openwrt by running:
       setenv bootcmd bootm 0xbf0a0000; saveenv;
       tftpboot 0c00000 <filename-of-initramfs-kernel>.bin;
       bootm 0c00000;
  * Copy sysupgrade image to /tmp on MR16
  * sysupgrade /tmp/<filename-of-sysupgrade>.bin

Notes:

  - There are two separate ARTs in the partition (offset 0x1000/0x5000 and
    0x11000/0x15000) in the OEM device. I suspect this is an OEM artifact;
    possibly used to configure the radios for different regions,
    circumstances or RF frontends. Since the ar71xx target uses the
    second offsets, use that second set (0x11000 and 0x15000) for the ART.

  - kmod-owl-loader is still required to load the ART partition into the
    driver.

  - The manner of storing MAC addresses is updated from ar71xx; it is
    at 0x66 of the 'config' partition, where it was discovered that the
    OEM firmware stores it. This is set as read-only. If you are
    migrating from ar71xx and used the method mentioned above to
    upgrade, use kmod-mtd-rw or UCI to add the MAC back in. One more
    method for doing this is described below.

  - Migrating directly from ar71xx has not been thoroughly tested, but
    one method has been used a couple of times with good success,
    migrating 18.06.2 to a full image produced as of this commit. Please
    note that these instructions are only for experienced users, and/or
    those still able to open their device up to flash it via the serial
    headers should anything go wrong.

    1) Install kmod-mtd-rw and uboot-envtools
    2) Run `insmod mtd-rw.ko i_want_a_brick=1`
    3) Modify /etc/fw_env.config to point to the u-boot-env partition.
       The file /etc/fw_env.config should contain:

       # MTD device   env offset  env size    sector size
       /dev/mtd1      0x00000     0x10000     0x10000

       See https://openwrt.org/docs/techref/bootloader/uboot.config
       for more details.

    4) Run `fw_printenv` to verify everything is correct, as per the
       link above.
    5) Run `fw_setenv bootcmd bootm 0xbf0a0000` to set a new boot address.
    6) Manually modify /lib/upgrade/common.sh's get_image function:
       Change ...

       cat "$from" 2>/dev/null | $cmd

       ... into ...

       (
         dd if=/dev/zero bs=1 count=$((0x66)) ; # Pad the first 102 bytes
         echo -ne '\x00\x18\x0a\x12\x34\x56'  ; # Add in MAC address
         dd if=/dev/zero bs=1 count=$((0x20000-0x66-0x6)) ; # Pad the rest
         cat "$from" 2>/dev/null | $cmd
       )

       ... which, during the upgrade process, will pad the image by
       128K of zeroes-plus-MAC-address, in order for the ar71xx's
       firmware partition -- which starts at 0xbf080000 -- to be
       instead aligned with the ath79 firmware partition, which
       starts 128K later at 0xbf0a0000.

    7) Copy the sysupgrade image into /tmp, as above
    8) Run `sysupgrade -F /tmp/<sysupgrade>.bin`, then wait

    Again, this may BRICK YOUR DEVICE, so make *sure* to have your
    serial cable handy.

Addenda:

  - The MR12 should be able to be migrated in a nearly identical manner as
    it shares much of its hardware with the MR16.

  - Thank-you Chris B for copious help with this port.

Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[fix typo in compat message, drop art DT label,
move 05_fix-compat-version to subtarget]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-31 17:41:21 +02:00
Thomas Petazzoni
168faef443 kernel: add options needed for SELinux
This adds a number of options to config/Config-kernel.in so that
packages related to SELinux support can enable the appropriate Linux
kernel support.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[rebase; add ext4, F2FS, UBIFS, and JFFS2 support; add commit message]
Signed-off-by: W. Michael Petullo <mike@flyn.org>
2020-08-31 01:15:41 +01:00
Hannu Nyman
55b73d6754 kernel: add missing symbol NET_DSA_TAG_RTL4_A
Fix build breakage caused by the missing kernel config symbol.

Fixes: 8735997686 ("kernel: backport RTL8366RB patches")
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-08-30 22:21:34 +02:00
Adrian Schmutzler
d7fb7ac278 ath79: increase kernel partition for ar9344 TP-Link CPE/WBS
The kernel has become too big again for the ar9344-based TP-Link
CPE/WBS devices which still have no firmware-partition splitter.

Current buildbots produce a kernel size of about 2469 kiB, while
the partition is only 2048 kiB (0x200000). Therefore, increase it
to 0x300000 to provide enough room for this and, hopefully, the
next kernel.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-30 22:20:37 +02:00
Adrian Schmutzler
4e4ee46495 ar71xx: drop target
This target has been mostly replaced by ath79 and won't be included
in the upcoming release anymore. Finally put it to rest.

This also removes all references in packages, tools, etc. as well as
the uboot-ar71xx and vsc73x5-ucode packages.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-30 22:18:35 +02:00
John Audia
05b8e84362 kernel: bump 5.4 to 5.4.61
Manually merged:
  backport-5.4
     011-kbuild-export-SUBARCH.patch
  layerscape
    701-net-0262-net-dsa-ocelot-add-tagger-for-Ocelot-Felix-switches.patch

All other modifications made by update_kernel.sh

Build-tested: x86/64, lantiq/xrx200, ramips/mt7621
Run-tested: ipq806x (R7800), lantiq/xrx200, x86/64, ramips (RT-AC57U)

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-30 19:44:47 +02:00
Christian Lamparter
f589bd9283 apm821xx: fix typos in .dts files
This patch fixes various typos or tab-vs-space issues in
the APM821XX device targets Device-Tree source files.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-08-29 17:15:09 +02:00
Christian Lamparter
e4c33462f9 apm821xx: use SPDX-License-identifiers
Please note that the DTS are based on really old .DTS from vendors
themselves.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-08-29 17:15:03 +02:00
Christian Lamparter
eb6bb94b12 apm821xx: apm821xx.dtsi fix comment styles
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-08-29 17:14:58 +02:00
Christian Lamparter
4ea5d443db apm821xx: MX60W: enumerate PCIe in device-tree
This patch adds the pcie-switch and bridge configuration for
the Meraki MX60W.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-08-29 17:14:55 +02:00
Christian Lamparter
1640e71e8e apm821xx: WNDR4700: delete wndr4700 board file
Thanks to the PCIE OF enumeration patch, this is technically
no longer needed.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-08-29 17:14:49 +02:00
Christian Lamparter
9153955095 apm821xx: MR24: enumerate PCIe in device-tree
This patch adds the pcie-switch and bridge configuration for
the Meraki MR24.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-08-29 17:14:44 +02:00
Christian Lamparter
b15420fc6c apm821xx: add missing cells-values for IIC1
These are copied over from the IIC0.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-08-29 17:14:42 +02:00
Christian Lamparter
90909ef4ba apm821xx: DTB: fix warnings related to sata-port warnings
This patch silences the following warnings:
>netgear-wndr4700.dts:168.3-13:Warning (reg_format): /plb/sata@bffd1800/sata-port@0:reg:property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
>netgear-wndr4700.dts:167.26-170.4: Warning (avoid_default_addr_size):/plb/sata@bffd1800/sata-port@0: Relying on default #address-cells value
>netgear-wndr4700.dts:167.26-170.4: Warning (avoid_default_addr_size):/plb/sata@bffd1800/sata-port@0: Relying on default #size-cells value

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-08-29 17:14:37 +02:00
Christian Lamparter
0facedb515 apm821xx: WNDAP6x0: enumerate PCIe in device-tree
This patch adds the pcie-switch and bridge configuration of the
WNDAP620 and WNDAP660.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-08-29 17:14:31 +02:00
Christian Lamparter
2c3f16d70e apm821xx: WNDR4700: enumerate PCIe in device-tree
This patch adds the pcie-switch and bridge configuration of the
WNDR4700.

This allows to get rid of the legacy firmware monikers and drop
the usbport LED declaration.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-08-29 17:14:27 +02:00
Daniel Golle
d75e753063 oxnas: kd20: revert accedintally commited change
Changing the factory image of KD20 was used during testing and wasn't
intended to be included in the commit fixing a SATA bug on oxnas.
Revert that part of the commit.

Fixes: 5793112f75 ("oxnas: reduce size of ATA DMA descriptor space")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-08-29 01:16:24 +01:00
Daniel González Cabanelas
42d14ace3e mvebu: LS421DE: add linkstation poweroff driver
Compile the Linkstation poweroff module for the Buffalo LS421DE.
Without this driver the device remains forever halted if a power off
command is executed.

The driver will also allow to use the WoL feature, which wasn't availabe
in the stock firmware.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-08-28 10:44:29 +01:00
Daniel González Cabanelas
59c200ca0a mvebu: backport linkstation-poweroff upstream driver
Backport the Linkstation poweroff driver from the kernel upstream (commit
a7f79f99541ef)

This driver is required by the Buffalo LinkStation LS421DE for a correct
power off operation. It also allows to use the WoL feature.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-08-28 10:44:29 +01:00
Perry Melange
09faa73c53 ramips: rt3883: use lzma-loader for DIR-645
The DIR-645 fails to boot if the kernel is large.
Enabling lzma-loader resolves the issue.

Run-tested on D-Link DIR-645.

Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
2020-08-28 00:25:34 +02:00
Georgi Vlaev
51b653de94 ramips: add support for Wavlink WL-WN531A6
This patch adds support for Wavlink WL-WN531A6 (Quantum D6).

Specifications:
--------------

* SoC: Mediatek MT7621AT 2C2T, 880MHz
* RAM: 128MB DDR3, Nanya NT5CB64M16GP-EK
* Flash: 16MB SPI NOR flash, GigaDevice GD25Q127CSIG
* WiFi 5GHz: Mediatek MT7615N (4x4:4) on mini PCIE slot.
* WiFi 2.4GHz: Mediatek MT7603EN (2x2:2) on mini PCIE slot.
* Ethernet: MT7630, 5x 1000Base-T
* LED: Power, WAN, LAN(x4), WiFi, WPS, dual color
       "WAVLINK" LED logo on the top cover.
* Buttons: Reset, WPS, "Turbo", touch button on the top
           cover via RH6015C touch sensor.
* UART: UART1: serial console (57600 8n1) on the J4 header
               located below the top heatsink.
        UART2: J12 header, located on the right side of
               the board.
* USB: One USB3 port.
* I2C: J9 header, located below the top heatsink.

Backup the OEM Firmware:
-----------------------

There isn't any firmware released for the WL-WN531A6 on
the Wavlink web site. Reverting back to the OEM firmware is
not possible unless we have a backup of the original OEM
firmware.

The OEM firmware is stored on /dev/mtd4 ("Kernel").

  1) Plug a FAT32 formatted USB flash drive into the USB port.
  2) Navigate to "Setup->USB Storage". Under the "Available
     Network folder" you can see part of the mount point of
     the newly mounted flash drive filesystem - e.g "sda1".
     The full mount point is prefixed with "/media", so in
     this case the mount point becomes "/media/sda1".
  3) Go to http://192.168.10.1/webcmd.shtml .
  4) Type the following line in the "Command" input box:

     dd if=/dev/mtd4ro of=/media/sda1/firmware.bin

  5) Click "Apply"
  6) After few seconds, in the text area should appear this
     output:

        30080+0 records in
      30080+0 records out

  7) Type "sync" in the "Command" input box and click "Apply".
  8) At this point the OEM firmware is stored on the flash
     drive as "firmware.bin". The size of the file is 15040 KB.

Installation:
------------

* Flashing instructions (OEM web interface):
The OEM web interface accepts only files with names containing
"WN531A6". It's also impossible to flash the *-sysupgrade.bin
image, so we have to flash the *-initramfs-kernel.bin first and
use the OpenWrt's upgrade interface to write the sysupgrade
image.

  1) Rename openwrt-ramips-mt7621-wavlink_wl-wn531a6-initramfs-kernel.bin
     to WN531A6.bin.
  2) Connect your computer to the one of the LAN ports of the
     router with an Ethernet cable and open http://192.168.10.1
  3) Browse to Setup -> Firmware Upgrade interface.
  4) Upload the (renamed) OpenWrt image - WN531A6.bin.
  5) Proceed with the firmware installation and give the device
     a few minutes to finish and reboot.
  6) After reboot wait for the "WAVLINK" logo on the top cover
     to turn solid blue, and open http://192.168.1.1
  7) Use the OpenWrt's "Flash Firmware" interface to write the
     OpenWrt sysupgrade image:
     openwrt-ramips-mt7621-wavlink_wl-wn531a6-squashfs-sysupgrade.bin

* Flashing instructions (u-boot TFTP):
  1) Configure a TFTP server on your computer and set its IP
     to 192.168.10.100
  2) Rename the OpenWrt sysupgrade image to firmware.bin and
     place it in the root folder of the TFTP server.
  3) Power off the device and connect an Ethernet cable from
     one of its LAN ports your computer.
  4) Press the "Reset" button (and keep it pressed)
  5) Power on the device.
  6) After a few seconds, when the connected port LAN LED stops
     blinking fast, release the "Reset" button.
  7) Flashing OpenWrt takes less than a minute, system will
     reboot automatically.
  8) After reboot the WAVLINK logo on the top cover will indicate
     the current OpenWrt running status (wait until the logo tunrs
     solid blue).

Revert to the OEM Firmware:
--------------------------
* U-boot TFTP:
  Follow "Flashing instructions (u-boot TFTP)" and use the
  "firmware.bin" backup image.

* OpenWrt "Flash Firmware" interface:
  Upload the "firmware.bin" backup image and select "Force update"
  before continuing.

Notes:
-----
* The MAC address shown on the label at the back of the device
is assigned to the 2.4G WiFi adapter.

  MAC addresses assigned by the OEM firmware:
  2.4G: *:XX (label): factory@0x0004
    5G: *:XX + 1    : factory@0x8004
   WAN: *:XX - 1    : factory@0xe006
   LAN: *:XX - 2    : factory@0xe000

* The I2C bus and UART2 are fully functional. The headers are
not populated.

Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
2020-08-28 00:25:33 +02:00
Andrew Freeman
ff5dd32164 ramips: add support for TP-Link TL-WR850N v2
This patch adds support for the TP-Link TL-WR850N v2. This device
is very similar to TP-Link TL-WR840 v4 and TP-Link TL-WR841 v13.

Specifications:
SOC: MediaTek MT7628NN
Flash: 8 MiB SPI
RAM: 64 MiB
WLAN: MediaTek MT7628NN
Ethernet: 5 ports (100M)

Installation Using the integrated tftp capability of the router:
1. Turn off the router.
2. Connect pc to one of the router LAN ports.
3. Set your PC IPv4 address to 192.168.0.66/24.
4. Run any TFTP server on the PC.
5. Put the recovery firmware on the root directory of TFTP server
   and name the file tp_recovery.bin
6. Start the router by pressing power button while holding the
   WPS/Reset button (or both WPS/Reset and WIFI buttons)
7. Router connects to your PC with IPv4 address 192.168.0.2,
   downloads the firmware, installs it and reboots. LEDs are
   flashing. Now you have OpenWrt installed.
8. Change your IPv4 PC address to something in 192.168.1.0/24
   network or use DHCP to get an address from your OpenWrt router.
9. Done! You can login to your router via ssh.

Forum link:
https://forum.openwrt.org/t/add-support-for-tp-link-tl-wr850n-v2/66899

Signed-off-by: Andrew Freeman <labz56@gmail.com>
[squash an tidy up commits, sort nodes]
Signed-off-by: Darsh Patel <darshkpatel@gmail.com>
[minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-27 16:36:18 +02:00
Adrian Schmutzler
6e936591f0 at91: explicitly set CONFIG_USB_SUPPORT for sam9x subtarget
The at91 target sets

  FEATURES:=usb usbgadget ...

in the target Makefile, which sets CONFIG_USB_SUPPORT=y in the
.config file for both subtargets.

However, when building with all kmods, the build fails with the
following error message:

  ERROR: module [...]/drivers/bluetooth/btusb.ko is missing.

It appears that only a part of the bluetooth files are compiled.
The package depends @USB_SUPPORT.

This can be easily healed by adding CONFIG_USB_SUPPORT=y to the
sam9x subtarget configuration. Before the 4.14->5.4 bump, the
same was also set in the target's config-4.14 file along with
several other USB config options that are not reimplemented.

Still, it remains a mystery to me why setting the same symbol
via target kernel config creates a different result than the
feature setting the same symbol in target-metadata.pl.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-27 16:36:18 +02:00
Hauke Mehrtens
e9b6dd3151 pistachio: Use kernel 5.4 by default
Kernel 5.4 should be stable enough.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-27 00:34:46 +02:00
Adrian Schmutzler
adf830a3a5 ramips: remove further mt7621 code from local ethernet driver
While commit 734a8c46e7 focussed on removing stuff directly
selected by the NET_RALINK_* symbols, this patch removes additional
unused mt7621-specific code from the ethernet driver.

As with the previous patch, the main reason is to reduce the amount
of code we have to maintain and care about.

Note that this patch still keeps a few lines with
IS_ENABLED(CONFIG_SOC_MT7621) in mtk_eth_soc.h/.c, as this file is
still selected for the mt7621 subtarget.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-26 23:58:01 +02:00
Adrian Schmutzler
18fbb9aa21 ath79: fix ethernet setup for some qca953x devices
On Comfast CF-E130N v2 and Mikrotik LHG HB board, the config
found in DTS appears to be strange:

- eth0 has "syscon","simple-mfd" set although it's not enabled
- eth1 is enabled redundantly (already "okay" in qca953x.dtsi)
- phy-handle is set for eth1 in DTS although it has a fixed-link
  in qca953x.dtsi

This seems like a copy-paste gone wrong. Remove the named options.

Run-tested on MikroTik LHG 2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-25 20:54:24 +02:00
Adrian Schmutzler
7f1540cc46 at91: introduce vendor_model scheme and drop board names
This introduces the vendor_model scheme to this target in order to
harmonize device names within the target and with the rest of
OpenWrt. In addition, custom board names are dropped in favor
of the generic script which takes the compatible.

Use the SUPPORTED_DEVICES variable to store the compatible where it
deviates from the device name, so we can use it in build recipes.

While at it, harmonize a few indents as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-25 19:28:42 +02:00
Hauke Mehrtens
186569e2e8 at91: Refresh kernel config
This was done by running:
make kernel_oldconfig CONFIG_TARGET=subtarget

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-25 19:28:42 +02:00
Sandeep Sheriker M
0d0a0d6649 at91: change dtb file path
Changing dtb file path since the dtb files are build in KDIR folder
with image- prefix.

Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
[remove commented lines]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-25 19:28:42 +02:00
Sandeep Sheriker M
a070e2ee42 at91: bump linux version to 5.4
Move patches to 5.4, put config only in subtarget directories.

Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
[refresh patches, add commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-25 19:28:42 +02:00
Pawel Dembicki
81ac2a73bc layerscape: add flashing manual for LS1012FRDM
LS1012FRDM is supported but there's no flashing instruction in README.

This patch adds it.

While at it, add a missing saveenv for MAC address setup.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[add comment about saveenv]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-25 16:42:21 +02:00
Linus Walleij
8735997686 kernel: backport RTL8366RB patches
These upstream patches makes the RTL8366RB DSA switch work
properly with OpenWrt, the D-Link DIR-685 gets network and
can be used as a router, and the same should be applicable
for any other device that want to enable the RTL8366RB
through Device Tree.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-08-24 18:53:59 +02:00
Adrian Schmutzler
36aa27189a kernel: bump 5.4 to 5.4.60
Deleted upstream patches:
  generic:
    041-genirq-affinity-Make-affinity-setting-if-activated-o.patch
  ipq806x:
    093-5-v5.8-ipq806x-PCI-qcom-Define-some-PARF-params-needed-for-ipq8064-SoC.patch
    093-6-v5.8-ipq806x-PCI-qcom-Add-support-for-tx-term-offset-for-rev-2_1_0.patch

Merged manually:
  ipq806x:
    093-4-v5.8-ipq806x-PCI-qcom-Use-bulk-clk-api-and-assert-on-error.patch
  layerscape:
    804-crypto-0016-MLKU-114-1-crypto-caam-reduce-page-0-regs-access-to-.patch

Build-tested: ath79/generic, ipq806x, layerscape/armv7, layerscape/armv8_64b
Run-tested: ipq806x (R7800)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-24 17:33:58 +02:00
Adrian Schmutzler
cc501ab021 kernel: set WATCHDOG_CORE dependency in kmod-hwmon-sch5627
For many target we have added CONFIG_WATCHDOG_CORE=y to the target
config due to the following error:

 Package kmod-hwmon-sch5627 is missing dependencies for the following
 libraries:
 watchdog.ko

However, actually the proper way appears to be setting the
dependency for the kmod-hwmon-sch5627 package, as the error message
demands.

Do this in this patch and remove the target config entries added
due to this issue.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-24 14:09:11 +02:00
Ansuel Smith
58d2bd88ae ipq806x: replace pci patchset with upstream version
Changes:
- Update patches
- Update dts with new binding
    Tx term offset dropped and replaced with a new compatible

Removed:
- 0071-5-PCI-qcom-Programming-the-PCIE-iATU-for-IPQ806x
    Pci init does the same exact thing (was needed in older kernel version)
- 0071-7-pcie-Set-PCIE-MRRS-and-MPS-to-256B
    Rejected upstream, can't find any reason to have this. No regression with
    testing it on R7800.

Tested on R7800 (ipq8065), R7500 v2 ("ipq8064-v2")

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
[rebase and refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-24 14:09:11 +02:00
Rustam Gaptulin
b2f19d3ef7 ramips: mt7621: use lzma-loader for ZBT-WG3526
The wg3526 fails to boot if the kernel is large.
Enabling lzma-loader resolves the issue on both the wg3526-16m
and wg3526-32m.

Fixes: FS#3143

Signed-off-by: Rustam Gaptulin <rascal6@gmail.com>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-24 00:18:43 +02:00
Joe Mullally
685d2513b5 ath79: fix/improve LED control for TL-WPA8630 v1/v2
The TL-WPA8630 v1 and v2 have the same LED Control GPIO configuration
according to the TP-Link GPL sources. Set the GPIO to output to make
it work and set to Active Low. It defaults to LEDs on at bootup.

To turn all LEDs off:
  echo 0 > /sys/class/gpio/tp-link\:led\:control/value
To turn all LEDs on:
  echo 1 > /sys/class/gpio/tp-link\:led\:control/value

Change the "LED" button from BTN_0 to KEY_LIGHTS_TOGGLE to match other
devices and the button guide, and to reduce the number of unintuitive
"BTN_X" inputs.

Fixes: ab74def0db ("ath79: add support for TP-Link TL-WPA8630P v2")

Signed-off-by: Joe Mullally <jwmullally@gmail.com>
[shorten commit title, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-22 15:13:15 +02:00
Adrian Schmutzler
441b36236f ipq806x: create shared DTSI for EA7500 v1 and EA8500
Most of the definitions for the two devices are shared, so put
them in a shared DTSI.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-22 14:20:25 +02:00
Felix Fietkau
f51f18e099 kernel: add patch that adds support for running threaded NAPI poll functions
This is helps on workloads with CPU intensive poll functions (e.g. 802.11)
on multicore systems

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-22 07:02:01 +02:00
Felix Fietkau
3f69f7dd84 uml: update to linux 5.4
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-22 07:02:01 +02:00
Felix Fietkau
9c5128854e kernel: backport a fix for a regression that broke IRQ affinity on ARM
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-21 20:44:53 +02:00
Adrian Schmutzler
734a8c46e7 ramips: remove legacy ethernet driver components for mt7621
The mt7621 subtarget has been switched to DSA quite a while ago and
seems to run sufficiently fine. Build with older kernels than 5.4 has
been disabled directly during the kernel bump, so our local ethernet
driver is unused in master since then.

Therefore, let's remove the mt7621-specific parts of "our" ethernet
driver, so we don't have to maintain them and it's obvious to
everybody that they are not used anymore.

This also drops the offloading components as this was specifically
implemented to depend on mt7621.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-21 15:46:54 +02:00
Adrian Schmutzler
373d4cc360 pistachio: use generic diag.sh
Remove local diag.sh in favor of generic one and add the required
led-* aliases to DTS.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-21 11:46:14 +02:00
Adrian Schmutzler
2549d1dd77 pistachio: use vendor_model scheme for device/image name
This uses the vendor_model scheme for the device/image name in
order to make this consistent to most other targets.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-21 11:46:14 +02:00
Hauke Mehrtens
5fa0e32698 pistachio: Add kmod-ca8210 wpan-tools by default
A ca8210 chip is soldered onto the board, add the driver by default.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-21 11:46:14 +02:00
Hauke Mehrtens
3f07a06b3b pistachio: Add SC16IS7XX device driver
This device is used to control extra UARTs and LEDs on the board.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-21 11:46:14 +02:00
Hauke Mehrtens
0d81afe3df pistachio: Add extra devices to dts file
This adds some extra devices to the DTS file.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-21 11:46:14 +02:00
Hauke Mehrtens
d2b63647cc pistachio: Add mtd device name from dts
Parse the "linux,mtd-name" property also for SPI NAND flashes.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-21 11:46:13 +02:00
Hauke Mehrtens
bdc7d9691d pistachio: Fix Null pointer access in pwm-img.c
This fixes a crash when booting the board.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-21 11:46:13 +02:00
Hauke Mehrtens
3cd9219e5e pistachio: Make patches and configuration apply on to of 5.4
This refreshes the patches, removes patches already applied upstream and
removes the SPI NAND framework to use the upstream version.

In addition it also refreshes the kernel configuration.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-21 11:46:13 +02:00
Hauke Mehrtens
4291a0d58a pistachio: Copy kernel 4.14 to 5.4
This only copies the patches and configuration without doing any
modification to the files.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-21 11:46:13 +02:00
Hauke Mehrtens
aefa9d39c3 kernel: Add GigaDevice GD5F4GQ4xC SPI NAND flash
This flash was found on the Imagination Technologies Creator Ci40 (Marduk).

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-21 11:46:13 +02:00
Adrian Schmutzler
eb531337a7 ath79: add support for TP-Link TL-WR710N v2.1
This adds support for the TP-Link TL-WR710N v2.1. It is basically a
re-issue of the v1.2.

Specifications:

SoC:       Atheros AR9331
CPU:       400 MHz
Flash:     8 MiB
RAM:       32 MiB
WiFi:      2.4 GHz b/g/n
Ethernet:  2x 100M ports
USB:       1x 2.0

The only difference from the v1 is the TP-Link hardware ID/revision.

Attention:
The TL-WR710N v2.0 (!) has only 4 MB flash and cannot be flashed with
this image. It has a different TPLINK_HWREV, so accidental flashing
of the factory image should be impossible without additional measures.

Unfortunately, the v2.0 in ar71xx has the same board name, so sysupgrade
from ar71xx v2.0 into ath79 v1/v2.1 will not be prevented, but will brick
the device.

Flashing instruction:

Upload the factory image via the OEM firmware GUI upgrade mechanism.

Further notes:

To make implementation easier if somebody desires to port the 4M v2.0,
this already creates two DTSI files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Fabian Eppig <fabian@eppig.de>
2020-08-21 11:34:55 +02:00
Aleksander Jan Bajkowski
14ae431c83 lantiq: remove vmmc node from FritzBox 7412 dts
As described in commit commit 891a700759 ("lantiq: enable second VPE
on Fritz!Box 7412"):

 The AVM Fritz!Box 7412 does not use the VMMC part of the Lantiq chip but
 rather a proprietary solution based on the DECT chip for the FXS ports.

We can remove last traces of vmmc in dts.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-08-20 23:45:39 +02:00
Adrian Schmutzler
83b1e40561 kernel: bump 5.4 to 5.4.59
Removed since added upstream:
  bcm27xx:
    950-0428-staging-vchiq_arm-Add-a-matching-unregister-call.patch
  lantiq:
    0800-spi-lantiq-ssc-Fix-warning-by-using-WQ_MEM_RECLAI.patch

Manually adjusted patches:
  layerscape:
    801-audio-0005-Revert-ASoC-fsl_sai-Add-support-for-SAI-new-version.patch

Build-tested: ath79/generic, ramips, lantiq/xrx200, lantiq/xway,
   mvebu/cortexa9, sunxi/a53
Run-tested: ipq806x (R7800), layerscape (LS1012A-FRDM, LS1046A-RDB)

Building on layerscape is only possible with workaround from PR #3179.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-By: John Audia <graysky@archlinux.us> [ipq806x]
Tested-by: Pawel Dembicki <paweldembicki@gmail.com> [layerscape]
2020-08-20 14:19:39 +02:00
Adrian Schmutzler
cf7c101135 layerscape: remove useless pairs of kernel patches
The layerscape kernel patches appears to be just some uncleaned local
development tree, where patches are sometimes directly followed by
their revert. While this does not seem a problem in the first place,
it becomes incredibly unpleasant when the upstream kernel changes in
the relevant areas and requires rebase.

This removes all these patch-revert pairs and refreshs the rest.

It removes about 44000 lines of entirely useless code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-20 14:19:39 +02:00
Petr Štetiar
a14f5bb4bd treewide: use wpad-basic-wolfssl as default
In order to support SAE/WPA3-Personal in default images. Replace almost
all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for
consistency. Keep out ar71xx from the list as it won't be in the next
release and would only make backports harder.

Build-tested (build-bot settings):
ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway,
sunxi: a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-20 14:19:39 +02:00
Adrian Schmutzler
cc75344044 bcm27xx: remove no-op patch pair
Patch 1 introduces a change, and patch 2 reverts it again. Remove
both patches and achieve the same outcome.

Refreshed patches for the target as well.

Cc: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-20 14:19:39 +02:00
John Audia
da98603597 kernel: bump 5.4 to 5.4.58
This PR is a blend of several kernel bumps authored by ldir taken from his
staging tree w/ some further adjustments made by me and update_kernel.sh

Summary:
Deleted upstreamed patches:
  generic:
    742-v5.5-net-sfp-add-support-for-module-quirks.patch
    743-v5.5-net-sfp-add-some-quirks-for-GPON-modules.patch
  bcm63xx:
    022-v5.8-mtd-rawnand-brcmnand-correctly-verify-erased-pages.patch
    024-v5.8-mtd-rawnand-brcmnand-fix-CS0-layout.patch
  mediatek:
    0402-net-ethernet-mtk_eth_soc-Always-call-mtk_gmac0_rgmii.patch

Deleted patches applied differently upstream:
  generic:
    641-sch_cake-fix-IP-protocol-handling-in-the-presence-of.patch

Manually merged patches:
  generic:
    395-v5.8-net-sch_cake-Take-advantage-of-skb-hash-where-appropriate.patch
  bcm27xx:
    950-0132-lan78xx-Debounce-link-events-to-minimize-poll-storm.patch
  layerscape:
    701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch

Build system: x86_64
Build-tested: ath79/generic, bcm27xx/bcm2708, bcm27xx/bcm2711,
  imx6, mvebu/cortexa9, sunxi/a53
Run-tested: Netgear R7800 (ipq806x)

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-By: Lucian Cristian <Lucian.cristian@gmail.com> [mvebu]
Tested-By: Curtis Deptuck <curtdept@me.com> [x86/64]
[do not remove 395-v5.8-net-sch_cake-Take-advantage-... patch,
adjust and refresh patches, adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-By: John Audia <graysky@archlinux.us> [ipq806x]
2020-08-18 18:14:54 +02:00
Thibaut VARÈNE
2cac31223d ath79: mikrotik: erase firmware on SPI NOR before install
On Mikrotik SPI NOR devices, the firmware partition must be erased when
flashing from stock firmware, otherwise leftover bits (in particular a
kernel signature) can trigger a boot loop.

When booted from initramfs (the only way to install OpenWRT on these
devices), this patch unconditionally erases the firmware partition in
the do_upgrade() stage for all supported SPI NOR devices.

This is forward-ported from ed49d0876 and 20452a8db

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-08-18 12:24:12 +02:00
Thibaut VARÈNE
d0498872ff generic: platform/mikrotik: fix incorrect test
The test is meant to check the result of the preceding kmalloc()

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-08-18 12:00:55 +02:00
Adrian Schmutzler
5388c72517 Revert "bcm53xx: remove useless echo in 02_network"
This reverts commit b1f6a5d9df.

In this particular case, the echo command was _not_ useless, but
converted the newlines back to spaces.

Add a comment into the code to make that obvious for the next one
looking at it like me.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-18 11:46:59 +02:00
Adrian Schmutzler
b1f6a5d9df bcm53xx: remove useless echo in 02_network
The output is already produced in the inner $() brackets, no need
to catch and echo it again.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 23:16:58 +02:00
Adrian Schmutzler
84fc80dd66 rockchip: remove useless echo in 40-net-smp-affinity
The command in the $() brackets will already provide the same output.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 23:13:57 +02:00
Adrian Schmutzler
1a75443964 apm821xx: tidy up 10-fix-wifi-mac
This applies some cosmetic style fixes:
- remove useless echo
- remove double equal sign (specific to bash)
- add quotes for -n check

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 23:09:37 +02:00
Adrian Schmutzler
e329e71c69 ath79: fix syntax error in ar7240_tplink_tl-wa.dtsi
The node needs to be terminated by a semicolon.

Fixes: 8484a764df ("ath79: ar724x: make sure builtin-switch is
enabled in DT")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 18:26:55 +02:00
Adrian Schmutzler
48c3d5c884 ath79: change WPS to Wifi button on TL-WPA8630P v2
Both TL-WPA8630(P) v1 and v2 feature a button labelled "WiFi".
While this is implemented as KEY_RFKILL for v1 in ar71xx and ath79,
the v2 sets it up as WPS button.

According to the manual, the behavior in OEM firmware is:
"Press and hold the button for 1 second to copy wireless settings
from the main router to the extender. Go to Wi-Fi Clone for more
information. Press and hold the button for at least 5 seconds to
turn the wireless function on or off."

Consequently, and since this is historic behavior on v1 in OpenWrt,
we set this button to KEY_RFKILL on both revisions.

Fixes: ab74def0db ("ath79: add support for TP-Link TL-WPA8630P v2")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 15:25:51 +02:00
Adrian Schmutzler
57e029ba57 ipq806x: move further common nodes to the DTSI files
The moves a few additional common nodes to the common DTSI files
for qcom-ipq8064-v2.0 and qcom-ipq8065 devices.

Remove a few redundant definitions on the way.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 15:25:11 +02:00
Adrian Schmutzler
8484a764df ath79: ar724x: make sure builtin-switch is enabled in DT
On ar7240/ar7241 the mdioX node with the builtin-switch is enabled
in the DTSI files, but the parent ethX node is left disabled. It
only gets enabled per device or device family, and has not been
enabled at all yet for the TP-Link WA devices with ar7240, making
the switch unavailable there.

This patch makes sure &eth0/&eth1 nodes are enabled together with
the &mdio0/&mdio1 nodes containing the builtin-switch.
For ar7240_tplink_tl-wa.dtsi, &eth0 is properly hidden again via
  compatible = "syscon", "simple-mfd";

This partially fixes FS#2887, however it seems dmesg still does
not show cable (dis)connect in dmesg for ar7240 TP-Link WA
devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 15:19:03 +02:00
Adrian Schmutzler
03cdbb2040 ramips: fix LED labels for Asus RT-AC65P
The leds block was copied over from the RT-AC85P DTS to the common
DTSI while keeping the device-specific model name in the label.

This moves the LEDs back to the DTS files and adjusts the names to
properly resemble the model name of the devices used at, just like
it is handled on most other devices.

Fixes: 7c5f712e4f ("ramips: add support for Asus RT-AC65P")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 15:00:43 +02:00
Adrian Schmutzler
e38d89ea55 at91: drop obsolete empty Makefiles
This files have been emptied during subtarget consolidation, but
not removed. Remove them now.

Fixes: aff084adf3 ("at91: Merge SAMA5 subtargets")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 01:22:36 +02:00
Donald Hoskins
eadb1a9437 octeon: add support for Itus Shield Router
Itus Networks Shield - 1Ghz dual-core mips64 / Cavium Octeon 3 SoC,
1Gb RAM, 4Gb eMMC,3 GbE 10/100/1000 ports

Information regarding device can be found:
https://deviwiki.com/wiki/Itus_Networks_Shield_Pro

Installing OpenWrt on Itus Networks Shield:

1) Boot Shield
2) On device: mount /dev/mmcblk1p1 /mnt
3) scp openwrt-octeon-itus,shield-router-initramfs-kernel.bin to
   /mnt/ItusrouterImage
3a) Optionally: scp openwrt-octeon-itus,shield-router-initramfs-kernel.bin
    to /mnt/ItusgatewayImage to allow you to have an emergency recovery
    boot in the GATEWAY slot - this slot will have no permament storage and
    is used for emergency recovery only when booted in the (G)ateway
    position
4) On device: umount /mnt
5) reboot

Once booted, run the sysupgrade via cli or luCi on the
openwrt-octeon-itus,shield-router-squashfs-sysupgrade.tar file the mode
you are running.

Once rebooted, the system installation is complete. Your storage partition
for the mode is inialized and set.

Signed-off-by: Donald Hoskins <grommish@gmail.com>
[cut out sysupgrade-* changes, move a few lines,
drop case CVMX_BOARD_TYPE_ITUS_SHIELD]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-16 02:15:06 +02:00
Donald Hoskins
591767fc01 octeon: determine sysupgrade-* directory for upgrade automatically
So far, the sysupgrade-* folder used during upgrade in octeon was
hardcoded to contain the board name. Therefore, changing board name
or BOARD_NAME variable in image/Makefile might have broken upgrade.

Improve this by adding a step to determine the folder name via
a wildcard, as it is done for generic nand_upgrade_tar() in
lib/upgrade/nand.sh.

While this still does not remove the problem for existing devices
(which still have the old script), it will entirely remove the
issue on newly added devices on this platform.

Signed-off-by: Donald Hoskins <grommish@gmail.com>
[split into separate patch, add commit message, add return values]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-16 02:14:34 +02:00
Adrian Schmutzler
d43b963b3d bcm63xx: reorganize board patches
This renames board patches to make finding devices easier
and reorders them based on their board.

The devices are grouped based on the board/cpu_id. New device
patches should be numbered based on their group.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-16 01:03:39 +02:00
Tomasz Maciej Nowak
ebf71533f9 ath79: add support for ALLNET ALL-WAP02860AC
ALLNET ALL-WAP02860AC is a dual-band wireless access point.

Specification
SoC: Qualcomm Atheros QCA9558
RAM: 128 MB DDR2
Flash: 16 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
      5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet: 1x 10/100/1000 Mbps AR8035-A, PoE capable (802.3at)
LEDS: 5x, which four are GPIO controlled
Buttons: 1x GPIO controlled
UART: 4 pin header near Mini PCIe card, starting count from white
      triangle on PCB
      1. VCC 3.3V, 2. GND, 3. TX, 4. RX
      baud: 115200, parity: none, flow control: none

MAC addresses
Calibration data does not contain valid MAC addresses.
The calculated MAC addresses are chosen in accordance with OEM firmware.

Because of:
a) constrained environment (SNMP) when connecting through Telnet
   or SSH,
b) hard-coded kernel and rootfs sizes,
c) checksum verification of kerenel and rootfs images in bootloder,

creating factory image accepted by OEM web interface is difficult,
therefore, to install OpenWrt on this device UART connection is needed.
The teardown is simple, unscrew four screws to disassemble the casing,
plus two screws to separate mainboard from the casing.
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.

Installation
1. Prepare TFTP server with OpenWrt initramfs-kernel image.
2. Connect to LAN port.
3. Connect to UART port.
4. Power on the device and when prompted to stop autoboot, hit any key.
5. Alter U-Boot environment with following commands:
    setenv failsafe_boot bootm 0x9f0a0000
    saveenv
6. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
   'setenv' to do that, then run following commands:
    tftpboot 0x81000000 <openwrt_initramfs-kernel_image_name>
    bootm 0x81000000
7. Wait about 1 minute for OpenWrt to boot.
8. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
   with:
    sysupgrade -n /tmp/<openwrt_sysupgrade_image_name>
9. After flashing, the access point will reboot to OpenWrt. Wait few
   minutes, until the Power LED stops blinking, then it's ready for
   configuration.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[add MAC address comment to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-15 15:58:39 +02:00
Tony Ambardar
2932b4d05e kernel: mips: fix init crash/bootloop on 64-bit systems
The malta subtargets for mips64 and mips64el fail to start the init process
at boot, resulting in a boot loop. The issue was raised and analyzed within
FS#3277. Investigation suggested code near the [vdso] memory area of the
process was long jumping into a region inaccessible to the process, e.g.

 init: - preinit -
 init: Launched preinit instance, pid=522
 do_page_fault(): sending SIGSEGV to init for invalid read access from 0000000000000360
 epc = 0000000000000360 in init[aaab42b000+4000]
 ra  = 000000fffee385e0 in
 Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
 Rebooting in 1 seconds..

Note the low-memory read access and epc are the same. Upstream kernel 5.6
included a relevant patch and discussion:

  * d3f703c4359f ("mips: vdso: fix 'jalr t9' crash in vdso code")

Disassembly of the failing kernel's vdso.so confirmed presence of the
telltale long jumps, e.g.:

00000000000007c0 <__vdso_clock_getres@@LINUX_2.6>:
 [...]
 7dc:   0320f809        jalr    t9
 [...]

Restore booting mips64/mips64el malta by backporting the above commit:
  * 310-v5.6-mips-vdso-fix-jalr-t9-crash-in-vdso-code.patch

Fixes: 54310a3aa0 ("malta: add kernel 5.4 config")
Fixes: FS#3277
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3277

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2020-08-15 00:04:59 +08:00
Adrian Schmutzler
7ef7dbaf70 ath79: add support for TP-Link TL-WPA8630 v1
This ports the TP-Link TL-WPA8630 v1 from ar71xx to ath79.

Specifications:

SoC: QCA9563
CPU: 750 MHz
Flash/RAM: 8 / 128 MiB
Ethernet: 3x 1G ports (QCA8337 switch)
WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac (ath10k)

Buttons, LEDs and network setup appear to be almost identical
to the v2 revision.

Powerline interface is connected to switch port 5 (Label LAN4).

Installation:

No "fresh" device was available for testing the factory image.

It is not known whether flashing via OEM firmware GUI is possible
or not. A discussion from 2018 [1] about that indicates a few
adjustments are necessary, but it is not clear whether those
are already implemented with the TPLINK_HEADER_VERSION = 2 or not.

Note that for the TL-WPA8630P v1, the TPLINK_HWID needs to be
changed to 0x86310001 to allow factory flashing.

[1] https://forum.openwrt.org/t/solved-tl-wpa8630p-lede-does-not-install/8161/27

Recovery:

Recovery is only possible via serial.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 20:43:15 +02:00
Adrian Schmutzler
488da882f5 mpc85xx: tidy up 10-fix-wifi-mac
This applies some cosmetic style fixes, mostly by removing useless
echo commands.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 20:29:20 +02:00
Adrian Schmutzler
ef765ceb09 ath79/mikrotik: add function for loading ath9k caldata
The commands to read ath9k caldata on mikrotik subtarget are
mostly repetitive, so let's put them into a function to make
writing and reading them easier.

This function will only be required when patching the MAC address.
For cases where it is put correctly into the calibration data by
the vendor, caldata_sysfsload_from_file can be used directly as
done for ath10k at the moment.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 12:47:45 +02:00
John Thomson
74438d5419 ramips: add support for MikroTik RouterBOARD 760iGS (hEX S)
This patch adds support for the MikroTik RouterBOARD 760iGS router.
It is similar to the already supported RouterBOARD 750Gr3.
The 760iGS device features an added SFP cage, and passive
PoE out on port 5 compared to the RB750Gr3.

https://mikrotik.com/product/hex_s

Specifications:

- SoC: MediaTek MT7621A
- CPU: 880MHz
- Flash: 16 MB
- RAM:  256 MB
- Ethernet: 5x 10/100/1000 Mbps
- SFP cage
- USB port
- microSD slot

Unsupported:

- Beeper (requires PWM driver)
- ZT2046Q (ADS7846 compatible) on SPI as slave 1 (CS1)
  The linux driver requires an interrupt, and pendown GPIO
  These are unknown, and not needed with the touchscreen
  only used for temperature and voltage monitoring.
  ads7846 hwmon:
  temp0 is degrees Celsius
  temp1 is voltage * 32

GPIOs:

- 07:  input passive PoE out (lan5) compatible (Mikrotik) device connected
- 17:  output passive PoE out (lan5) switch

Installation through RouterBoot follows the usual MikroTik method
https://openwrt.org/toh/mikrotik/common

To boot to intramfs image in RAM:

1. Setup TFTP server to serve intramfs image.
2. Plug Ethernet cable into WAN port.
3. Unplug power, hold reset button and plug power in.
   Wait (~25 seconds) for beep and then release reset button.
   The SFP LED will be lit in RouterBoot, but will not be lit in OpenWRT.
4. Wait for a minute. Router should be running OpenWrt,
   check by plugging in to port 2-5 and going to 192.168.1.1.

To install OpenWrt to flash:

1. Follow steps above to boot intramfs image in RAM.
2. Flash the sysupgrade.bin image with web interface or sysupgrade.
3. Once the router reboots you will be running OpenWrt from flash.

OEM firmware differences:

- RouterOS assigns a different MAC address for each port
- The first address (E01 on the sticker) is used for wan (ether1 in OEM).
- The next address is used for lan2.
- The last address (E06 on the sticker) is used for sfp.

[Initial port work, shared dtsi]
Signed-off-by: Vince Grassia <vincenzo.grassia@zionark.com>
[SFP support and GPIO identification]
Signed-off-by: Luka Logar <luka.logar@iname.com>
[Misc. fixes and submission]
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[rebase, drop uart3 from state_default on 750gr3, minor commit
title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 12:47:45 +02:00
Adrian Schmutzler
ddf3e5c22d ramips/mt7621: create common DTSI for Mikrotik devices
This moves some common definitions for Mikrotik devices, mainly
routerboot partitions and reset key, to a common DTSI file.

While at it, remove unused hard_config DT label.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 12:47:45 +02:00
John Thomson
2d9db93397 ramips: use gpio-export for Mikrotik RouterBOARD 750Gr3 beeper
This beeper hardware requires a PWM driver for frequency selection.
Since the GPIO driver does not provide that, revert the beeper
support to a simple gpio-export.

This effectively reverts the corresponding changes from
6ba58b7b02 ("ramips: cleanup the RB750Gr3 support")

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 02:12:12 +02:00
Ansuel Smith
87e92d50e5 kernel: usb: move phy-qcom-ipq806x-usb to ipq806x modules.mk
This driver is only used by ipq806x SoCs. Move it there and drop
dependency from ipq40xx since it's not used anywere.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[rebase on changes to previous patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
2020-08-13 02:12:12 +02:00
Ansuel Smith
35d1f05094 ipq806x: replace nvmem qcom patch with upstream version
- Replace nvmem qcom patch with upstream version
- Update compatible

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[refresh patches, minor commit message rewording]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
2020-08-13 02:12:12 +02:00
Ansuel Smith
0c45ad41e1 ipq806x: replace phy dwc3 patch with upstream version
- Replace dwc3 phy patch with upstream version
- Rework the dts to use the upstream bindings
- Update changed config flags
- Rename module to reflect config name

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[fix qcom,tx-deamp_3_5db typo, refresh patches, rename kmod]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
2020-08-13 02:12:12 +02:00
Adrian Schmutzler
6e7f40dff3 ath79: routerboard-92x: ensure explicit bios size in DTSI
The missing "size" property was acceptable in the context of a single
DTS as the underlying device is known to have a 64KB flash, and thus
the bios partition fit exactly between the preceding and following ones.

However as this block has moved in a DTSI, for the sake of clarity and
explicitness the size property is added to ensure that if the flash
happens to be larger than expected, the bios partition remains properly
sized.

Suggested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 16:49:34 +02:00
Adrian Schmutzler
5dc74ad7f3 ath79: harmonize appearance of ethX nodes in qca953x DTSes
This harmonizes the appearance of ethX nodes in qca953x DTSes by:
- having the same order of nodes and properties
- removing redundant status property on eth1 (set in qca953x.dtsi)

This is meant to help both copy-pasters and reviewers, since
deviations and errors can be spotted easier.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:44:07 +02:00
Adrian Schmutzler
92b4f16bab kernel: add CGROUPS and IOSCHED_BFQ back to config
After those symbols have been removed from generic kernel config,
they were added to the target config during every kernel config
refresh. As that's not desirable, add them back to the generic
config.

Fixes: d1a8217d87 ("kernel: clean-up build-configurable kernel config symbols")
Fixes: cfe235c436 ("kernel: modules: add package kmod-iosched-bfq")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:03:17 +02:00
Roger Pueyo Centelles
151e43df7a ath79: add support for MikroTik SXT 5nD r2 (SXT Lite5)
The MikroTik SXT Lite5 (product code RBSXT5nDr2, also SXT 5nD r2) is
an outdoor 5GHz CPE with a 16 dBi integrated antenna built around the
Atheros AR9344 SoC. It is based on the "sxt5n" board platform.

Specifications:
 - SoC: Atheros AR9344
 - RAM: 64 MB
 - Storage: 128 MB NAND
 - Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2
 - Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port,
    8-32 Vdc PoE in
 - 6 user-controllable LEDs:
  · 1x power (blue)
  · 1x wlan (green)
  · 4x rssi (green)
 - 1 GPIO-controlled buzzer

 See https://mikrotik.com/product/RBSXT5nDr2 for more details.

Notes:
 The device was already supported in the ar71xx target. There, the
 Ethernet port was handled by GMAC1. Here in ath79 it is handled by
 GMAC0, which allows to get link information (loss, speed, duplex) on
 the eth0 interface.

Flashing:
 TFTP boot initramfs image and then perform sysupgrade. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Acknowledgments:
 Michael Pratt (@mpratt14) for helping on the network settings.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, use mikrotik LED label prefix, make names consistent,
add reg for bootloader2, use led_user for boot indication etc.,
minor cosmetic changes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:03:17 +02:00
Sven Roederer
b2e1f7101d ath79: add support for MikroTik RouterBOARD 921GS-5HPacD-15s
The MikroTik RouterBOARD 921GS-5HPacD-15s (mANTBox 15s) is an outdoor
antenna for 5 GHz with an built-in router. This ports the board from
ar71xx.

See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9558 (720 MHz)
 - RAM: 128 MB
 - Storage: 128 MB NAND
 - Wireless: external QCA9892 802.11a/ac 2x2:2
 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
 - SFP: 1x host

Working:
 - NAND storage detection
 - Ethernet
 - Wireless
 - 1x user LED (blinks during boot, sysupgrade)
 - Reset button
 - Sysupgrade

Untested:
 - SFP cage (probably not working)

Installation (untested):
 - Boot initramfs image via TFTP and then flash sysupgrade image

As the embedded RB921-pcb is a stripped down version of the RB922 this patch
adds a common dtsi for this series and includes this to the final dts-files.

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[move ath10k-leds closer to ath10k definition in DTS files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:03:17 +02:00
Roger Pueyo Centelles
7a705c067f ath79: add support for MikroTik RouterBOARD LHG 2nD
The MikroTik RouterBOARD LHG 2nD (sold as LHG 2) is a 2.4 GHz
802.11b/g/n outdoor device with a feed and an integrated dual
polarization grid dish antenna based on the LHG-HB platform.

See https://mikrotik.com/product/lhg_2 for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9533
 - RAM: 64 MB
 - Storage: 16 MB NOR
 - Wireless: Atheros AR9531 (SoC) 802.11b/g/n 2x2:2, 18 dBi antenna
 - Ethernet: Atheros AR8229 (SoC), 1x 10/100 port, 12-28 Vdc PoE in
 - 8 user-controllable LEDs:
   · 1x power (blue)
   · 1x user (green)
   · 1x lan (green)
   · 1x wlan (green)
   · 4x rssi (green)

Note:
 The rssihigh LED is disabled, as it shares GPIO 16 with the reset
 button.

Flashing:
 TFTP boot initramfs image and then perform sysupgrade. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, remove rssiled setup, adjust commit message, add DTSIs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:03:17 +02:00
Felix Fietkau
ed19ba04e8 mediatek: disable btif in device tree to make the WMAC work again
btif and wmac access the same resources and at the moment enabling one
breaks the other

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-12 13:02:13 +02:00
Felix Fietkau
74a66c0204 mediatek: fix PCI device tree node for elecom wrc-2533gent
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-12 13:02:13 +02:00
Adrian Schmutzler
d0cb71a896 bcm47xx: use vendor_model scheme for device/image names
Most targets have been updated to consistently use the vendor_model
scheme for device definitions and thus, image names.

Apply this to bcm47xx as well. This does _not_ apply any other
specific naming changes.

Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 11:08:05 +02:00
Adrian Schmutzler
683bcbdce1 bcm53xx: use vendor_model scheme for device/image names
Most targets have been updated to consistently use the vendor_model
scheme for device definitions and thus, image names.

Apply this to bcm53xx as well. This does _not_ apply any other
specific naming changes.

Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 11:08:05 +02:00
Hauke Mehrtens
c43af7a6cb kernel: Fix cake patch for kernel 4.19.138
This fixes the following build problem with cake:
net/sched/act_ctinfo.c: In function 'tcf_ctinfo_act':
net/sched/act_ctinfo.c:99:6: error: implicit declaration of function 'tc_skb_protocol'; did you mean 'skb_protocol'? [-Werror=implicit-function-declaration]
  if (tc_skb_protocol(skb) == htons(ETH_P_IP)) {
      ^~~~~~~~~~~~~~~
      skb_protocol
  CC [M]  net/sched/sch_hfsc.o

Fixes: fdac05b741 ("kernel: Update kernel 4.19 to version 4.19.138")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-11 21:11:53 +02:00
Hauke Mehrtens
2e8785d68c kernel: Create UBIFS v5 volume
In commit 87b35c16ad ("kernel: ubifs: create use file system format 4
by default") we changed the default UBIFS version used when the kernel
creates a new volume from 5 to 4. UBIFS v5 was added in kernel 4.10 and
only kernel 4.10 and later can read it.
We changed the kernel to create version 4 volumes also on more recent
kernel versions to make it possible to downgrade to an OpenWrt version
with kernel 4.9, the upgrade still works. This is probably not needed
any more and we can remove this patch.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-11 21:11:53 +02:00
Álvaro Fernández Rojas
a5a0b3f1d0 bcm63xx: switch to upstream CFE detection patch
This patch has been merged in linux 5.9.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-11 08:04:40 +02:00
Tony Ambardar
da4651833c malta: disable unnecessary built-in CDROM support
The CDROM is not needed for booting and can be included by selecting the
loadable module as a package instead.

This also avoids triggering a memory allocation failure during probing of
the CDROM due to lack of low 16MB DMA memory, as decribed in FS#3278:
https://bugs.openwrt.org/index.php?do=details&task_id=3278

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/3289
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2020-08-11 11:25:42 +08:00
Daniel Golle
5793112f75 oxnas: reduce size of ATA DMA descriptor space
After years of trying to find the reason for random kernel crashes
while both CPU and SATA are under load it has been found.
Some odd commented-out #defines in kref's single-port driver [1] which
were copied from the vendor driver made me develop a theory:
The IO-mapped memory area for DMA descriptors apparetly got some holes
just before the alignment boundaries.
This feels like an off-by-one bug in the hardware or maybe those fields
are used internally by the SATA controller's firmware.
Whatever the cause is: they cannot be used and trying to use them
results in reading back unexpected stuff and ends up with oopsing
Unable to handle kernel paging request at virtual address d085c004

Work around the issue by reducing the area used for bmdma descriptors.
This reduces SATA performance (iops) quite a bit, but finally makes
things work reliably. Possibly one could optimize this much more by
really just skipping the holes in that memory area -- however, that
seems to be non-trivial with the driver and libata in it's current form
(suggestions are welcome).
The 'proper' way to have good SATA performance would be to make use of
the hardware RAID features (one can use the JBOD mode to access even
just a single disc transparently through the RAID controller integrated
in the SATA host instead of accessing the SATA ports 'raw' as we do
now).

[1]: https://github.com/kref/linux-oxnas/blob/master/drivers/ata/sata_oxnas.c#L25

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-08-11 00:16:04 +01:00
Christoph Krapp
0af656e978 ar71xx: fix ZyXEL NBG6616 wifi switch
The device uses a rf-kill switch instead of a button. Furthermore the
GPIO is active high.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2020-08-11 01:12:22 +02:00
Hauke Mehrtens
b35c54227b kernel: Move CONFIG_IONIC to generic kernel config
It is deactivated everywhere, just set this in the generic config.

Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-10 23:58:58 +02:00
Hauke Mehrtens
eafdd1a0fc malta: Refresh kernel configuration
This refreshes the kernel configuration on top of kernel 5.4.
It now builds without asking to select some kernel options on all 4
subtargets.
It still does not boot up, there is a different problem.

Tested-By: Yousong Zhou <yszhou4tech@gmail.com>
Acked-By: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-10 23:58:58 +02:00
Hauke Mehrtens
2f3d7abccd kernel: Update kernel 4.14 to version 4.14.193
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-10 19:34:37 +02:00
Hauke Mehrtens
fdac05b741 kernel: Update kernel 4.19 to version 4.19.138
Compile and run tested on lantiq/xrx200

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-10 19:34:37 +02:00
Christoph Krapp
459c8c9ef8 ath79: add support for ZyXEL NBG6616
Specifications:

  SoC: Qualcomm Atheros QCA9557
  RAM: 128 MB (Nanya NT5TU32M16EG-AC)
  Flash: 16 MB (Macronix MX25L12845EMI-10G)
  Ethernet: 5x 10/100/1000 (1x WAN, 4x LAN)
  Wireless: QCA9557 2.4GHz (nbg), QCA9882 5GHz (ac)
  USB: 2x USB 2.0 port
  Buttons: 1x Reset
  Switches: 1x Wifi
  LEDs: 11 (Pwr, WAN, 4x LAN, 2x Wifi, 2x USB, WPS)

MAC addresses:

WAN *:3f uboot-env ethaddr + 3
LAN *:3e uboot-env ethaddr + 2
2.4GHz *:3c uboot-env ethaddr
5GHz *:3d uboot-env ethaddr + 1

The label contains all four MAC addresses, however the one without
increment is first, so this one is taken for label MAC address.

Notes:

The Wifi is controlled by an on/off button, i.e. has to be implemented
by a switch (EV_SW). Despite, it appears that GPIO_ACTIVE_HIGH needs
to be used, just like recently fixed for the NBG6716.
Both parameters have been wrong at ar71xx.

Flash Instructions:

At first the U-Boot variables need to be changed in order to boot the
new combined image format. ZyXEL uses a split kernel + root setup and
the current kernel is too large to fit into the partition. As resizing
didnt do the trick, I've decided to use the prefered combined image
approach to be future-kernel-enlargement-proof (thanks to blocktrron for
the assistance).

First add a new variable called boot_openwrt:
setenv boot_openwrt bootm 0x9F120000

After that overwrite the bootcmd and save the environment:
setenv bootcmd run boot_openwrt
saveenv

After that you can flash the openwrt factory image via TFTP. The servers
IP has to be 192.168.1.33. Connect to one of the LAN ports and hold the
WPS Button while booting. After a few seconds the NBG6616 will look for
a image file called 'ras.bin' and flash it.

Return to vendor firmware is possible by resetting the bootcmd:
setenv bootcmd run boot_flash
saveenv
and flashing the vendor image via the TFTP method as described above.

Accessing the U-Boot Shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:

|    Hit any key to stop autoboot:  3

The user is then dropped to a locked shell.

| NBG6616> ?
| ATEN	x,(y)     set BootExtension Debug Flag (y=password)
| ATSE	x         show the seed of password generator
| ATSH	          dump manufacturer related data in ROM
| ATRT	(x,y,z,u) ATRT RAM read/write test (x=level, y=start addr, z=end addr, u=iterations
| ATGO	          boot up whole system
| ATUR	x         upgrade RAS image (filename)

In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!

First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.

| NBG6616> ATSE NBG6616
| 00C91D7EAC3C

This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):

- tool.sh -
ror32() {
  echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -

| # bash ./tool.sh 00C91D7EAC3C
| ATEN 1,10FDFF5

Copy and paste the result into the shell to unlock zloader.

| NBG6616> ATEN 1,10FDFF5

If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.

| NBG6616> ATGU
| NBG6616#

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[move keys to DTSI, adjust usb_power DT label, remove kernel config
change, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 18:37:43 +02:00
Adrian Schmutzler
d4ac0ad543 treewide: make dependency on kmod-usb-net selective
A bunch of kernel modules depends on kmod-usb-net, but does not
select it. Make AddDepends/usb-net selective, so we can drop
some redundant +kmod-usb-net definitions for DEVICE_PACKAGES.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 12:54:30 +02:00
Nicholas Smith
c00b8dcf72 ath79: add support for Telco T1
Description:
    2x 100Mbps Etherent ports
    24V passive PoE
    64MB RAM
    16MB Flash
    2.4GHz WiFi
    1x WiFi antenna (RP-SMA connector)
    1x LTE antenna (SMA connector)
    Sierra Wireless MC7430 LTE modem

Flash instructions:
    Original firmware is based on OpenWrt.
    Flash using sysupgrade -n

SUPPORTED_DEVICES is added to support factory firmware.

Signed-off-by: Nicholas Smith <nicholas.smith@telcoantennas.com.au>
[add missing led_rssi0 DT label, add SUPPORTED_DEVICES]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 12:49:29 +02:00
Aleksander Jan Bajkowski
37df722266 ath79: increase spi frequency on TL-WDR3500/3600/4300/4310
SPI Flash chip supports up to 33 MHz wihout fast read opcode.
Available frequencies are 112.5, 56.25, 37.5, 28.125, 22.5 etc.
This patch increases the nominal maximum frequency to 33 MHz,
reaching an effective increase from 22.5 to 28.125 MHz.

Formula to calculate SPI frequency:
Freq = 225 MHz / 2 / div

Before:

$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real	0m 3.58s
user	0m 0.00s
sys	0m 3.57s

After:

$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real	0m 2.95s
user	0m 0.00s
sys	0m 2.93s

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 12:43:37 +02:00
Adrian Schmutzler
04b99d9539 ramips/mt7628: fix portmap based on board.d port assignment
When comparing to the port assignment in board.d/02_network, a few
devices seem to use the wrong setup of mediatek,portmap.

The corrects the values for mt76x8 subtarget based on the location
of the wan port.

A previous cleanup of obviously wrong values has already been done in
7a387bf9a0 ("ramips: mt76x8: fix bogus mediatek,portmap")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 12:33:38 +02:00
Andreas Böhler
ab74def0db ath79: add support for TP-Link TL-WPA8630P v2
The TL-WPA8630P v2 is a HomePlug AV2 compatible device with a QCA9563 SoC
and 2.4GHz and 5GHz WiFi modules.

Specifications
--------------

  - QCA9563 750MHz, 2.4GHz WiFi
  - QCA9888 5GHz WiFi
  - 8MiB SPI Flash
  - 128MiB RAM
  - 3 GBit Ports (QCA8337)
  - PLC (QCA7550)

MAC address assignment
----------------------

WiFi 2.4GHz and LAN share the same MAC address as printed on the label.
5GHz WiFi uses LAN-1, based on assumptions from similar devices.

LAN Port assignment
-------------------

While there are 3 physical LAN ports on the device, there will be 4
visible ports in OpenWrt. The fourth port (internal port 5) is used
by the PowerLine Communication SoC and thus treated like a regular
LAN port.

Versions
--------

Note that both TL-WPA8630 and TL-WPA8630P, as well as the different
country-versions, differ in partitioning, and therefore shouldn't be
cross-flashed.

This adds support for the two known partitioning variants of the
TL-WPA8630P, where the variants can be safely distinguished via the
tplink-safeloader SupportList. For the non-P variants (TL-WPA8630),
at least two additional partitioning schemes exist, and the same
SupportList entry can have different partitioning.
Thus, we don't support those officially (yet).

Also note that the P version for Germany (DE) requires the international
image version, but is properly protected by SupportList.

In any case, please check the OpenWrt Wiki pages for the device
before flashing anything!

Installation
------------

Installation is possible from the OEM web interface. Make sure to
install the latest OEM firmware first, so that the PLC firmware is
at the latest version. However, please also check the Wiki page
for hints according to altered partitioning between OEM firmware
revisions.

Additional thanks to Jon Davies and Joe Mullally for bringing
order into the partitioning mess.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
[minor DTS adjustments, add label-mac-device, drop chosen, move
common partitions to DTSI, rename de to int, add AU support strings,
adjust TPLINK_BOARD_ID, create common node in generic-tp-link.mk,
adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 11:48:08 +02:00
Daniel Golle
cfe235c436 kernel: modules: add package kmod-iosched-bfq
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-08-10 09:52:31 +01:00
Christoph Krapp
982c1f6e42 ar71xx: change u-boot-env to read-write for ZyXEL NBG6616
As the ath79 port of this device uses a combined kernel + root
partition the uboot bootcmd variable needs to be changed. As using
cli/luci is more convenient than opening up the case and using a uart
connection, lets unlock the uboot-env partition for write access.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2020-08-09 23:57:17 +02:00
Felix Fietkau
5d8fded26a kernel: add missing config symbols
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-09 14:01:52 +02:00
Adrian Schmutzler
e81e625ca3 treewide: add sysupgrade comment for early DSA-adopters
Add a specific comment for early DSA-adopters that they can keep
their config when prompted due to compat-version increase.

This is a temporary solution, the patch should be simply reverted
before any release.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 20:56:12 +02:00
Adrian Schmutzler
372529d311 ath79: add support for TP-Link TL-WA901ND v3
This ports support for the TL-WA901ND v3 from ar71xx to ath79.
Most of the hardware is shared with the TL-WA850/860RE v1 range
extenders. It completes the TL-WA901ND series in ath79.

Specifications:
  Board: AP123 / AR9341
  Flash/RAM: 4/32 MiB
  CPU: 535 MHz
  WiFi: 2.4 GHz b/g/n
  Ethernet: 1 port (100M)

Flashing instructions:
  Upload the factory image via the vendor firmware upgrade option.

This has not been tested on device, but port from ar71xx is
straightforward and the device will be disabled by default anyway.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 20:40:48 +02:00
Ansuel Smith
df3ad130d5 ipq806x: replace patches with upstream version
Replace all the custom patches with the backported upstream version

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[refresh patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 18:07:17 +02:00
Adrian Schmutzler
4f1a51f438 ath79: drop redundant kmods-leds-gpio
The ath79 target has CONFIG_LEDS_GPIO=y set in kernel config, so
no need to pull the kmod-leds-gpio module for specific devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 16:13:51 +02:00
Adrian Schmutzler
1eac573b53 ramips: mt7621: implement compatibility version for DSA migration
This implements the newly introduced compat-version to prevent
broken upgrade between swconfig and DSA for ramips' mt7621 subtarget.

In order to make the situation more transparent for the user, and
to prevent large switch-cases for devices, it is more convenient to
have the entire subtarget 1.1-by-default. This means that new devices
will be added with 1.1 from the start, but in contrast we don't need
to switch them in board.d files. Apart from that, users that manually
backport devices to 19.07 with swconfig will have an equivalent
upgrade experience to officially supported devices.

Since DSA support on mt7621 is out for a while already, this applies
the same uci-defaults workaround for early adopters as already
done for kirkwood and mvebu in previous commits.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 16:13:51 +02:00
Adrian Schmutzler
86c89bf5e8 kirkwood: fix sysupgrade experience for early DSA-adopters
Conceptually, the compat-version during sysupgrade is meant to
describe the config. Therefore, if somebody starts with a device on
19.07 and swconfig, and that person does a forceful upgrade into a
DSA-based firmware without wiping his/her config, then the local
compat-version should stay at 1.0 according to the config present
(and not get updated).

However, this poses a problem for those people that early-adopted
DSA in master, as they already have adjusted their config for DSA,
but it still is "1.0" as far as sysupgrade is concerned. This can
be healed by a simple

   uci set system.@system[0].compat_version="1.1"
   uci commit system

But this needs to be applied _after_ the upgrade (as the "old" fwtool
on the old installation does not know about compat_version) and it
requires access via SSH (i.e. no pure GUI solution is available for
this group of people, apart from wiping their config _again_ for
no technical reason). Despite, the situation will not become
obvious to those just upgrading via GUI, they will just have the
experience of a "broken upgrade".

This is a conflict which cannot be resolved by achieving both goals,
we have to decide to either keep the strict concept or improve the
situation for early adopters.

In this patch, we address the issue by providing a uci-defaults
script that will raise the compat_version for _all_ people upgrading
into a 1.1 image, no matter whether they have reset config or not.
The idea is to implement this as a _temporary_ solution, so early
adopters can upgrade into the new mechanism without issues, and
after a few weeks/months we could remove the uci-defaults script
again.

If we e.g. remove the script just before 20.xx.0-rc1, early adopters
should have moved on by then, and existing stable users would still
get the intended experience.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 16:13:51 +02:00
Adrian Schmutzler
a9703db720 mvebu: fix sysupgrade experience for early DSA-adopters
Conceptually, the compat-version during sysupgrade is meant to
describe the config. Therefore, if somebody starts with a device on
19.07 and swconfig, and that person does a forceful upgrade into a
DSA-based firmware without wiping his/her config, then the local
compat-version should stay at 1.0 according to the config present
(and not get updated).

However, this poses a problem for those people that early-adopted
DSA in master, as they already have adjusted their config for DSA,
but it still is "1.0" as far as sysupgrade is concerned. This can
be healed by a simple

   uci set system.@system[0].compat_version="1.1"
   uci commit system

But this needs to be applied _after_ the upgrade (as the "old" fwtool
on the old installation does not know about compat_version) and it
requires access via SSH (i.e. no pure GUI solution is available for
this group of people, apart from wiping their config _again_ for
no technical reason). Despite, the situation will not become
obvious to those just upgrading via GUI, they will just have the
experience of a "broken upgrade".

This is a conflict which cannot be resolved by achieving both goals,
we have to decide to either keep the strict concept or improve the
situation for early adopters.

In this patch, we address the issue by providing a uci-defaults
script that will raise the compat_version for _all_ people upgrading
into a 1.1 image, no matter whether they have reset config or not.
The idea is to implement this as a _temporary_ solution, so early
adopters can upgrade into the new mechanism without issues, and
after a few weeks/months we could remove the uci-defaults script
again.

If we e.g. remove the script just before 20.xx.0-rc1, early adopters
should have moved on by then, and existing stable users would still
get the intended experience.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 16:13:51 +02:00
Sungbo Eo
de78747de1 ramips: use lzma-loader for RT5350F-OLinuXino devices
The bootloader fails to extract a big kernel, e.g. v5.4 kernel image
with ALL_KMODS enabled. This can be fixed by using lzma-loader.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-08 16:13:51 +02:00
Sungbo Eo
a40ddc2195 ramips: adjust LZMA_TEXT_START for 32MB RAM devices
Currently the lzma-loader is placed in RAM at 32MB offset, which does not
make sense for devices with only 32MB RAM. If we adjust LZMA_TEXT_START to
24MB offset, then the lzma-loader can be used on those devices and still
about 24MB memory will be available for uncompressed image, which should be
enough for most use cases.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-08 16:13:51 +02:00
Adrian Schmutzler
1634461bd2 ramips: switch rt288x subtarget to kernel 5.4
The sbutarget has testing support for kernel 5.4 for quite a while
and builds fine, however, only one devices there is > 4 MiB.

Since it's unlikely to get a Tested-by for that device, and the other
ralink subtargets appear to be working with 5.4 so far, let's set
this target to 5.4 by default as well.

That way, even if the device happens to break, we'll still have at
least usable SDK and IB for people to use.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-07 14:51:20 +02:00
Adrian Schmutzler
7c07a0f4c3 ramips/mt7620: fix portmap based on board.d port assignment
When comparing to the port assignment in board.d/02_network, many
devices seem to use the wrong setup of mediatek,portmap.

The corrects the values for mt7620 subtarget based on the location
of the wan port.

A previous cleanup of obviously wrong values has already been done in
d3c0a94405 ("ramips: mt7620/mt7621: remove invalid mediatek,portmap")

Cc: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-07 13:01:18 +02:00
Adrian Schmutzler
121c021989 ramips: invert wpad selection for mt7621
For ramips/mt7621, the wpad-basic package is not selected by default,
but added for every device individually as needed.

While this might be technically correct if the SoC does not come with
a Wifi module, only 18 of 97 devices for that platform are set up
_without_ wpad-basic currently.

Therefore, it seems more convenient to add wpad-basic by default for
the subtarget and then just remove it for the 18 mentioned devices,
instead of having to add it for about 60 times instead.

This would also match the behavior of the 5 other subtargets, where
wpad-basic/wpad-mini is added by default as well, and thus be more
obvious to developers without detailed SoC knowledge.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-07 12:02:19 +02:00
Álvaro Fernández Rojas
24f7ae814a bcm63xx: add missing endif board comnents
This provides better context for board patches.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 11:09:06 +02:00
Álvaro Fernández Rojas
0c109df7f0 bcm63xx: merge RTA770BW and RTA770W board patches
The only difference between both boards is the DSL annex.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 10:34:31 +02:00
Álvaro Fernández Rojas
eddf863650 bcm63xx: add missing fallback SPROMs
A couple of SPROM IDs are missing.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 10:34:31 +02:00
Álvaro Fernández Rojas
fb589b6142 bcm63xx: add missing OHCI nodes
All boards with EHCI enabled should also have OHCI enabled.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 10:34:31 +02:00
Álvaro Fernández Rojas
440d5996ef bcm63xx: remove invalid EHCI nodes
There's no EHCI controller on BCM6348.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 10:34:31 +02:00
Álvaro Fernández Rojas
81fdb4235e bcm63xx: refactor board patches
Current board patches format is crazy.
Let's try to put some order.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 10:34:31 +02:00
Adrian Schmutzler
7673df7994 ramips: switch rt3883 subtarget to kernel 5.4
The target has testing support for kernel 5.4 for quite a while,
compiles fine for all devices, and has been run-tested on Asus
RT-N56U successfully.

Let's set it to kernel 5.4 by default to increase the audience
before an 20.xx stable branch.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Eneas U de Queiroz <cotequeiroz@gmail.com> [Asus RT-N56U]
2020-08-06 23:52:57 +02:00
Álvaro Fernández Rojas
92727a1228 bcm63xx: switch to upstream CFE version detection patch
The patch improving CFE version detection has been merged (linux 5.9).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-06 23:06:12 +02:00
Álvaro Fernández Rojas
f41a40001a bcm63xx: switch to upstream endif comments patch
This allows better context for board patches and we no longer need a
downstream patch for that.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-06 23:06:12 +02:00
Álvaro Fernández Rojas
9fb1d4ce8a bcm63xx: switch to upstream LED patch
The patch adding support for the second LED HW blinking interval has been
merged (linux 5.9).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-06 23:06:12 +02:00
Daniel Golle
728a0c68d1 Revert "procd: update to git HEAD"
This reverts commit e0e607f0d0.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-08-06 16:17:37 +01:00
Davy Hollevoet
394f54ee62 ath79/nand: add support for Netgear WNDR4300TN
This patch adds support for the WNDR4300TN, marketed by Belgian ISP
Telenet. The hardware is the same as the WNDR4300 v1, without the
fifth ethernet port (WAN) and the USB port. The circuit board has
the traces, but the components are missing.

Specifications:
* SoC: Atheros AR9344
* RAM: 128 MB
* Flash: 128 MB NAND flash
* WiFi: Atheros AR9580 (5 GHz) and AR9344 (2.4 GHz)
* Ethernet: 4x 1000Base-T
* LED: Power, LAN, WiFi 2.4GHz, WiFi 5GHz, WPS
* UART: on board, to the right of the RF shield at the top of the board

Installation:

* Flashing through the OEM web interface:
  + Connect your computer to the router with an ethernet cable and browse
    to http://192.168.0.51/
  + Log in with the default credentials are admin:password
  + Browse to Advanced > Administration > Firmware Upgrade in the Telenet
    interface
  + Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img
  + Proceed with the firmware installation and give the device a few
    minutes to finish and reboot.

* Flashing through TFTP:
  + Configure your wired client with a static IP in the 192.168.1.x range,
    e.g. 192.168.1.10 and netmask 255.255.255.0.
  + Power off the router.
  + Press and hold the RESET button (the factory reset button on the bottom
    of the device, with the gray circle around it, next to the Telenet logo)
    and turn the router on while keeping the button pressed.
  + The power LED will start flashing orange. You can release the button
    once it switches to flashing green.
  + Transfer the image over TFTP:
    $ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img

Signed-off-by: Davy Hollevoet <github@natox.be>
[use DT label reference for adding LEDs in DTSI files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 16:56:07 +02:00
Shibajee Roy
a673ac66fa ramips: add support for Netgear JWNR2010 v5
Specification:
 - CPU: MediaTek MT7620N (580 MHz)
 - Flash size: 4 MB NOR SPI
 - RAM size: 32 MB DDR1
 - Bootloader: U-Boot
 - Wireless: MT7620N 2x2 MIMO 802.11b/g/n (2.4 GHz)
 - Switch: MT7620 built-in 10/100 switch with vlan support
 - Ports: 4x LAN, 1x WAN
 - Others: 7x LED, Reset button, UART header on PCB (57600 8N1)

Flash instructions:
 1. Use ethernet cable to connect router with PC/Laptop, any router
    LAN port will work.
 2. To flash openwrt we are using nmrpflash[1].
 3. Flash commands:
      First we need to identify the correct Ethernet id.

        nmrpflash -L

        nmrpflash -i net* -f openwrt-ramips-mt7620-netgear_jwnr2010-v5-squashfs-factory.img

      This will show something like "Advertising NMRP server on net*..." (net*, *=1,2,3... etc.)

 4. Now remove the power cable from router back side and immediately connect it again.
    You will see flash notification in CMD window, once it says reboot the device just
    plug off the router and plug in again.

Revert to stock:
 1. Download the stock firmware from official netgear support[2].
 2. Follow the same nmrpflash procedure like above, this time just use the stock firmware.

        nmrpflash -i net* -f N300-V1.1.0.54_1.0.1.img

MAC addresses on stock firmware:
LAN = *:28 (label)
WAN = *:29
WLAN = *:28

On flash, the only valid MAC address is found in factory 0x4.

Special Note:
 This openwrt firmware will also support other netgear N300 routers like below as they
 share same stock firmware[3].
 JNR1010v2 / WNR614 / WNR618 / JWNR2000v5 / WNR2020 / WNR1000v4 / WNR2020v2 / WNR2050

[1] https://github.com/jclehner/nmrpflash
[2] https://www.netgear.com/support/product/JWNR2010v5.aspx
[3] http://kb.netgear.com/000059663

Signed-off-by: Shibajee Roy <ador250@protonmail.com>
[create DTSI, use netgear_sercomm_nor, disable by default, add MAC
addresses to commit message, add label MAC address]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 16:56:07 +02:00
Adrian Schmutzler
a66449c608 ramips: drop remaining m25p,chunked-io from DTS
This option was a spi nor hack which is dropped in commit bcf4a5f474
("ramips: remove chunked-io patch and set spi->max_transfer_size instead")

Most of it has already been removed in
be2b61e4f1 ("ramips: drop m25p,chunked-io from dts")

It seems all current usages were added after that. Remove them.

Cc: Chuanhong Guo <gch981213@gmail.com>
Reported-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 16:56:07 +02:00
Adrian Schmutzler
3b89849b57 ramips: add common definition netgear_sercomm_nor
Like NAND-based devices, SPI-NOR based Netgear devices also share
a common setup for their images. This creates a common defition
for them in image/Makefile, so it can be reused across subtargets.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 16:56:06 +02:00
Daniel Golle
e0e607f0d0 procd: update to git HEAD
47a9f0d service: add method to query available container features
 afbaba9 initd: attempt to mount cgroup2
 ead60fe jail: use pidns semantics also for timens
 759e9f8 jail: make use of BLOBMSG_CAST_INT64 for OCI rlimits
 83053b6 instance: add instances into unified cgroup hierarchy
 16159bb jail: parse OCI cgroups resources

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-08-06 15:27:51 +01:00
Adrian Schmutzler
77e850fe76 ramips: tidy up MAC address setup for Linkit Smart and Omega2
Linkit Smart 7688 and Onion Omega 2(+) are one-port devices, and
have their port set to LAN by default. Setting up a WAN MAC address
for them doesn't make any sense, as no wan interface will be created
in uci config. Despite, these devices also set lan_mac in 02_network,
although mtd-mac-address sets a different address for the ethernet
interface in DTS.

Clean this up by moving the lan_mac value into DTS and dropping the
entries in 02_network completely. That way, the effective address
on the LAN interface should stay the same, but we get rid of the
extra (re)assignments.

As I don't have access to the devices, this does not tell anything
about whether 0x2e is actually a good choice, it just preserves
the existing assignment.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 13:33:26 +02:00
Tobias Welz
633ea0db0f ramips: WizFi630S use macs from factory partion
WIZnet WizFi630s has three mac addresses in the factory partition:
0x04 (also on the label), 0x28 for wan mac and 0x2e as lan mac.
All three macadresses are sequential series of addresses.
This is making use of them.

While at it, also add the label MAC address to 02_network.

MAC addresses as verified by OEM firmware:

use      interface   source
WLAN     ra0         factory 0x04 (label)
WAN      eth0.2      factory 0x28 (label + 1)
LAN      eth0.1      factory 0x2e (label + 2)

Signed-off-by: Tobias Welz <tw@wiznet.eu>
[fix sorting in 02_network, commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 13:33:26 +02:00
Tobias Welz
d0b229f553 ramips: correct WizFi630S pin mappings
WizFi630S had some pins changed in the release version of the board.
The run led, wps button and a slide switch where affected.
This patch is correcting this.
i2c is removed as it is sharing a pin with the run (system) led.
uart2 is enabled as it is also enabled in the OEM firmware.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
2020-08-06 13:33:26 +02:00
Adrian Schmutzler
d1db1f4240 ipq40xx: refresh kernel 5.4 config
Refresh config with make kernel_oldconfig.

After d1a8217d87 ("kernel: clean-up build-configurable kernel
config symbols"), the routine wants to add an additional
CONFIG_CGROUPS (=n), which has been removed manually again, as
this seems unintended.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 12:51:51 +02:00
Felix Fietkau
431b177afa mediatek: fix mt7622-rfb1 board support
Make GPIO keys active-low.
Add DSA support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-06 12:42:43 +02:00
Felix Fietkau
b0f7ea2853 kernel: unify CONFIG_GPIO_SYSFS in kernel configs
Enable it for all platforms

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-06 12:37:04 +02:00
Alexey Dobrovolsky
4c73c34ec4 ramips: switch rt305x subtarget to kernel 5.4
RT3x5x seems to work fine with kernel 5.4. Set the default kernel
version to 5.4 to bring this to a broader audience.

Since 4 of 6 targets are on kernel 5.4 now, invert the kernel
version setup logic in Makefile/target.mk files.

Tested on ZyXEL Keenetic.

Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[invert version setup logic]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-05 23:27:35 +02:00
Tobias Welz
816973f42a ramips: enable flashing WizFi630S via OEM firmware
WIZnet WizFi630s board name is written slightly different it its OEM
OpenWrt firmware. This causes an incompatibility warning during flashing
with sysupgrade. This patch is adding the vendor board name to the
supported devices list to avoid this warning. For initial flashing you
can use sysupgrade via command line or luci beside of TFTP.
Do not keep the OEM configuration during sysupgrade.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
2020-08-05 23:08:03 +02:00
Adrian Schmutzler
7c1c0a00fc ipq806x: use qcom-ipq8064-v1.0.dtsi from upstream
This uses upstream qcom-ipq8064-v1.0.dtsi and modifies it by patches
instead of keeping a local version. As a consequence:

- we use a part of the shared definitions there and update device
  DTS files accordingly
- we move additional stuff from our local v1.0.dtsi to the patch
- we drop partitions, LEDs and keys from the file as we will
  implement them differently anyway

Like with the previous patch, this follows the idea that a diff
from upstream might be easier to handle than a big file of our
own with different distribution pattern of properties.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-05 23:08:03 +02:00
Adrian Schmutzler
b7b7c2a6ad ipq806x: use qcom-ipq8064.dtsi from upstream
Though a qcom-ipq8064.dtsi file exists upstream, we still do overwrite
it with a full version of our own in the ipq806x target. About half of
the contents of our file are upstream content, the other half are local
improvements.

To prevent us from having a lot of code maintained twice in parallel,
this adjusts the target to use the upstream qcom-ipq8064.dtsi. Our
local changes are arranged into three patches, the first pulling a
commit from upstream, the second doing a few small adjustments, and
the third adding all additional stuff.

This should get us the best of both worlds.

The property "ports-implemented" on sata@29000000 is moved to
2nd-level DTSI files as kernel defines it there as well.

While at, rename 080-ARM-dts-qcom-add-gpio-ranges-property.patch to
include the kernel version where it's added upstream.

Even though this might look more complicated in the first place,
the aim is to bring our files closer to upstream, so we can benefit
from changes directly and vice-versa. After all, this drop about
650 lines just copied from the upstream DTSI file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-05 23:08:03 +02:00
Tobias Welz
b735bbcb18 ramips: remove doublet entry in WizFi630S dts file
&wmac entry in WIZnet WizFi630S dts file was existing two times.
This is removing one of them.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
2020-08-05 12:10:15 +02:00
Tobias Welz
36d4c2272e ramips: disable unused phy ports of WizFi630S
WIZnet WizFi630S is using only 3 of the phy ports. The unused phy ports
draw unnecessarily power. This is disabling the unused phy ports.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
2020-08-05 12:10:15 +02:00
Rafał Miłecki
e47bec489f bcm47xx: switch to kernel 5.4
Switch, LEDs, USB, buttons, sysupgrade testedon BCM4706.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-04 15:51:08 +02:00
Rafał Miłecki
7125323b81 bcm53xx: switch to kernel 5.4
Switch, USB, WiFi, buttons tested on BCM47094.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-04 13:28:56 +02:00
Rafał Miłecki
36c53e0dd2 bcm53xx: set HW_RANDOM_BCM2835=y
This enables Random Number Generator support on Northstar (described in
DT with brcm,bcm5301x-rng).

It's also a workaround for OpenWrt bug with kernel config causing:
Broadcom BCM2835/BCM63xx Random Number Generator support (HW_RANDOM_BCM2835) [Y/n/m/?] (NEW)

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-04 13:27:19 +02:00
Rafał Miłecki
c8c9876607 bcm53xx: update kernel 5.4 DTS to upstream 5.9 state
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-04 13:27:19 +02:00
Rafał Miłecki
b9cd55b88e bcm53xx: update kernel 5.4 config
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-04 13:27:19 +02:00
Richard Fröhning
009e62c92c ramips: add support for TP-Link RE200 v3
TP-Link RE200 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2.

Specifications
--------------

- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button

Unverified:
- UART header on PCB (57600 8n1)

There are 2.4G and 5G LEDs in red and green which are controlled
separately.

MAC addresses
-------------

MAC address assignment has been done according to the RE200 v2.

The label MAC address matches the OpenWrt ethernet address.

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Recovery
--------

Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.

The device has not been opened for adding support. However, it is expected
that the behavior is similar to the RE200 v2. Instructions for serial console
and recovery may be checked out in commit 6d6f36ae78 ("ramips: add support
for TP-Link RE200 v2") or on the device's Wiki page.

Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[adjust commit title/message, sort support list]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 23:34:34 +02:00
Adrian Schmutzler
1deaf695ec ramips: fix/tidy up 4M tplink-v2-image flash layouts
For the TP-Link 4M devices with tplink-v2-image recipe
(mktplinkfw2.c), there are two different flash layouts based
on the size of the (u)boot partition:

device         uboot    OEM firmware  OpenWrt (incl. config)
tl-wr840n-v5   0x20000  0x3c0000      0x3d0000
tl-wr841n-v14  0x10000  0x3d0000      0x3e0000

In both cases, the 0x10000 config partition is used for the firmware
partition as well due to the limited space available and since it's
recreated by the OEM firmware anyway.

However, the TFTP flashing process will only copy data up to the
size of the initial (OEM) firmware size. Therefore, while we can
use the bigger partition to have additional erase blocks on the
device, we have to limit the image sizes to the TFTP limits.

So far, only one layout definition has been set up in mktplinkfw2.c
for 4M mediatek devices. This adds a second one and assigns them
to the devices so the image sizes are correctly restrained.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 12:17:08 +02:00
Adrian Schmutzler
18b7d87a8f kirkwood: get rid of BOARD_NAME and tidy up DEVICE_DTS
Since most of the DTS file names follow a common scheme now, let's
update the automatically generated DEVICE_DTS value and get rid
of some DEVICE_DTS and all BOARD_NAME entries for individual devices.

This should specifically make the job easier for developers adding
new devices, as they are not tempted to copy over BOARD_NAME anymore.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 10:47:22 +02:00
Adrian Schmutzler
356866c481 target: replace remaining occurrences of ifconfig with ip
ifconfig is effectively deprecated for quite some time now. Let's
replace the remaining occurrences for our target setup by the
corresponding ip commands now.

Note that this does not touch ar71xx, as it will be dropped anyway,
and changing it would only make backports harder.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 10:42:04 +02:00
Sungbo Eo
c90db26e05 ar71xx: restore support for boot console with arbitrary baud rates
Commit 1bfbf2de6d ("ar71xx: serial: core: add support for boot console
with arbitrary baud rates") added support for arbitrary baud rates which
enabled 250000 baud rate for Yun. But the patch was not ported to kernel
4.9, and since then the kernel set its baud rate to 9600. This commit ports
the patch to kernel 4.14, thereby restoring the serial console of Yun.

Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 18:10:06 +02:00
Sungbo Eo
a5e404d192 ar71xx: enable ethernet LED of Arduino Yun
Commit 05d73a2a73 enabled GPIO on ethernet LED, but proper LED setup was
not added then. This commit fixes it by reverting the change on the LED.

Fixes: 05d73a2a73 ("ar71xx: Arduino Yun board 'WLAN RST' button support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 16:34:21 +02:00
Sungbo Eo
58dc1d0637 ar71xx: fix sysupgrade for Arduino Yun
Commit bb46b635df changed its partition scheme, but sysupgrade image
validation still uses the old format. This commit fixes it so that
force flag is not needed for sysupgrade.

Fixes: bb46b635df ("ar71xx: move Arduino Yun to generic building code")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 16:34:21 +02:00
Sungbo Eo
43896dc0b0 Revert "ar71xx: fix Arduino Yun enabling of level shifters outputs"
This reverts commit 077253dd66.

The output enable pins should be disabled by default, and only enabled when
used. Otherwise unwanted conflicts might occur between MCU and SoC pins.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 16:34:21 +02:00
Adrian Schmutzler
8a8ef4ed86 ath79/mikrotik: create shared device definitions for nor and nand
Move the image preparation and nand-utils package selection into
common device definitions for NOR/NAND devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-01 18:31:24 +02:00
Stijn Tintel
5c3e83fa88 kernel: fix missing TRANSPARENT_HUGEPAGE symbols
Enabling KERNEL_TRANSPARENT_HUGEPAGE exposes 2 missing symbols:
* CONFIG_READ_ONLY_THP_FOR_FS
* TRANSPARENT_HUGEPAGE_ALWAYS
* TRANSPARENT_HUGEPAGE_MADVISE

The first one was added in 5.4, and is marked experimental there so just
disable it in the generic config.

For the latter two, we should not force the user to use either of them,
so add them as build-configurable kernel options.

Fixes: d1a8217d87 ("kernel: clean-up build-configurable kernel config symbols")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2020-08-01 14:33:46 +01:00
Stijn Tintel
1bff9f5b78 kernel: add missing config symbol
This symbol is exposed on ARM64 with EFI enabled in the kernel config.
Currently this happens only on ipq807x, but as there might be new ARM64
targets with EFI in the future it is better to add the symbol to the
generic config.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Jo-Philipp Wich <jo@mein.io>
2020-08-01 15:19:11 +03:00
Linus Walleij
9e02580d52 gemini: Add swap partition to DNS-313
Sometimes when using the DNS-313 memory usage can peak and
with a simple swap partition we can avoid running into the
roof and invoking the OOM killer. Set this partition to
128MB (twice the size of the memory of the DNS-313).

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-07-31 18:34:40 +02:00
Christian Lamparter
caa6ada969 apm821xx: disable WNDR4700 5.4 image
The compressed image that the buildbots are building is too large for
the netgear uboot and it crashes and soft-bricks the device.

| Uncompressing Kernel Image ...
| LZMA: uncompress or overwrite error 1 - must RESET board to recover

The whole target likely needs to be switched zImage which is a major
hassle due to powerpc's legacy bootwrapper setup as compared to ARM.
So for now, disable the device.

Reported-by: Wiktor Stasiak (FS#3258)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-07-31 18:17:34 +02:00
Adrian Schmutzler
65305cb448 kirkwood: use real model names for Linksys devices
This replaces the internal device names "Audi" and "Viper" with the
real model names, which a user would look for. This makes the
Linksys devices on this target consistent with the names recently
changed for mvebu based on the same idea.

As a consequence, the "viper" device definition is split into two
separate definitions with the correct names for both real models.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 15:03:43 +02:00
Tony Ambardar
a4856dab0d kernel: mips: restore missing MIPS32 cBPF JIT
Kernel v5.1 included an eBPF JIT for MIPS32 kernels, but problems were
discovered [1] and the changes later reverted in kernel v5.5 with commits:

  * f8fffebdea75 ("MIPS: BPF: Disable MIPS32 eBPF JIT")
  * 36366e367ee9 ("MIPS: BPF: Restore MIPS32 cBPF JIT")

Only the first of these was backported to LTS kernel 5.4, leaving cBPF
programs without a JIT and introducing a performance regression for any
such users e.g. libpcap, tcpdump, etc.

Restore cBPF performance by backporting the second commit above:
  * 070-v5.5-MIPS-BPF-Restore-MIPS32-cBPF-JIT.patch

[1] https://lore.kernel.org/bpf/20191205182318.2761605-1-paulburton@kernel.org/

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2020-07-31 13:42:14 +01:00
Adrian Schmutzler
664237deaa mvebu: fix alphabetic sorting in 02_network
This has been overlooked when removing solidrun,clearfog-a1 entry.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Adrian Schmutzler
e496eefccc mvebu: increase compat version for SolidRun ClearFog Base
When changing the Pro variant to DSA, the ethernet interface rename
script was dropped by all devices to keep them in sync:

  be309bfd74 ("mvebu: drop 06_set_iface_mac preinit script")

Therefore, network config will be broken after upgrade for the
Base variant as well. Increase the compat version and provide a
message to signal that to the users.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Adrian Schmutzler
090779b24e kirkwood: implement compatibility version for DSA migration
This implements the newly introduced compat-version to prevent
upgrade between swconfig and DSA for kirkwood.

Just define a compat version with minor increment and an appropriate
message for both image (in Makefile) and device (in base-files).

Since we never removed SUPPORTED_DEVICES for this target, we don't
have to add it back either.

Attention:

All users that already updated to the DSA versions in master will
receive the same incompatibility warning since their devices are still
"1.0" as far as fwtool can tell.
Those, and only those, can bypass the upgrade check by using force (-F)
without having to reset config again. In addition, the new version
string needs to be put into uci config manually, so the new fwtool
knows that it actually deals with a "1.1":

   uci set "system.@system[-1].compat_version=1.1"
   uci commit system

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Adrian Schmutzler
494f12c52d mvebu: implement compatibility version for DSA migration
This implements the newly introduced compat-version to prevent
upgrade between swconfig and DSA for mvebu.

Just define a compat version with minor increment and an appropriate
message for both image (in Makefile) and device (in base-files).

Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES
that have been removed in previous patches to prevent broken config.

Attention:

All users that already updated to the DSA versions in master will
receive the same incompatibility warning since their devices are still
"1.0" as far as fwtool can tell.
Those, and only those, can bypass the upgrade check by using force (-F)
without having to reset config again. In addition, the new version
string needs to be put into uci config manually, so the new fwtool
knows that it actually deals with a "1.1":

   uci set "system.@system[-1].compat_version=1.1"
   uci commit system

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Robinson Wu
84cb0f7ace ramips: add support for JS76x8 series DEV boards
This commit adds support for the Jotale JS76x8 series development boards.
These devices have the following specifications:

- SOC: MT7628AN/NN, MT7688AN, MT7628DAN
- RAM of MT7628AN/NN and MT7688AN: 64/128/256 MB (DDR2)
- RAM of MT7628DAN: 64 MB (DDR2)
- FLASH:8/16/32 MB (SPI NOR)
- Ethernet:3x 10/100 Mbps ethernet ports (MT76x8 built-in switch)
- WIFI:1x 2T2R 2.4 GHz Wi-Fi
- LEDs:1x system status green LED, 1x wifi green LED,
       3x ethernet green LED
- Buttons:1x reset button
- 1x microSD slot
- 4x USB 2.0 port
- 1x mini-usb debug UART
- 1x DC jack for main power (DC 5V)
- 1x TTL/RS232 UART
- 1x TTL/RS485 UART
- 13x GPIO header
- 1x audio codec(wm8960)

Installation via OpenWrt:

The original firmware is OpenWrt, so both LuCI and sysupgrade can be used.

Installation via U-boot web:

1. Power on board with reset button pressed, release it
   after wifi led start blinking.
2. Setup static IP 192.168.1.123/4 on your PC.
3. Go to 192.168.1.8 in browser and upload "sysupgrade" image.

Installation via U-boot tftp:
1. Connect to serial console at the mini usb, which has been connected to UART0
   on board (115200 8N1)
2. Setup static IP 192.168.1.123/4 on your PC.
3. Place openwrt-firmware.bin on your PC tftp server (192.168.1.123).
3. Connect one of LAN ports on board to your PC.
4. Start terminal software (e.g. screen /dev/ttyUSB0 115200) on PC.
5. Apply power to board.
6. Interrupt U-boot with keypress of "2".
7. At u-boot prompts:
   Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
   Input device IP (192.168.1.8) ==:192.168.1.8
   Input server IP (192.168.1.123) ==:192.168.1.123
   Input Linux Kernel filename (root_uImage) ==:openwrt-firmware.bin
8. board will download file from tftp server, write it to flash and reboot.

Signed-off-by: Robinson Wu <wurobinson@qq.com>
[add license to DTS files, fix state_default and reduce to the mimimum,
move phy0tpt trigger to DTS, drop ucidef_set_led_timer, fix network ports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
David Bauer
ced167d729 ramips: limit 5GHz channels for RAVPower RP-WD009
When selecting a channel below 100 on the 5GHz radio, the channel will
be detected as busy all the time.

Survey data from wlan1
	frequency:			5240 MHz [in use]
	channel active time:		165729 ms
	channel busy time:		158704 ms
	channel transmit time:		0 ms

Channels 100 and above work fine:

Survey data from wlan1
	frequency:			5500 MHz
	channel active time:		133000 ms
	channel busy time:		21090 ms
	channel transmit time:		0 ms

Limit the available channels, so users do not have the impression
their device is broken.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-30 22:33:53 +02:00
Petr Štetiar
e9f7923a1d treewide: mark devices as BROKEN instead of commenting out
This adds the newly introduced BROKEN flag to a bunch of devices
that previously just had TARGET_DEVICES commented out. By this, we
can select them in make menuconfig when BROKEN developer config option
is selected, instead of having to edit the code.

In contrast to DEFAULT := n, this is meant to cover devices that
don't boot or don't compile at all.

ath25: np25g, wpe53g
  both disabled during kernel bump 3.18->4.4 without reason given
  f89a20a89a ("ath25: update kernel from 3.18 to 4.4")

bcm53xx: linksys-ea6300-v1, linksys-ea9200, linksys-ea9500
  broken due to insufficient/broken TRX support
  55ff15cfd5 ("bcm53xx: disable building Linksys EA6300 V1 image")
  cd0f9900a4 ("bcm53xx: parepare for building more Linksys images")

bcm63xx: tplink-archer-c5-v2, tplink-archer-c9-v1
  disabled when kernel 5.4 support was added, probably broken
  50c6938b95 ("bcm53xx: add v5.4 support")

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[limit to subset of devices, use BROKEN, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-30 21:49:22 +02:00
Petr Štetiar
504000d520 treewide: use DEFAULT := n to disable non-broken devices
This uses DEFAULT := n on a bunch of devices that previously were
"disabled" by commenting out TARGET_DEVICES. This will allow to
build them without having to modify the code, but they will not
be selected for default build or buildbots.

The change is applied to all devices that are not "broken", but suffer
from image site limitations or similar, or have been added in the past
but never confirmed to run on the device properly:

at91: at91-q5xr5:
  kernel image too big
  31aeae0774 ("at91: do not build image for at91-q5xr5")

bcm47xx: asus-rt-ac66u:
  disabled since it was added in 2015
  69aefc771f ("brcm47xx: build images for Asus devices")

bcm47xx: netgear-wndr3400-vcna, netgear-wnr3500u, netgear-wnr3500-v2-vc
  added disabled in 2012, but never confirmed to work on devices
  5dec9dd3b2 ("brcm47xx: add code to generate images for some netgear
    devices")

bcm53xx: netgear-r8500
  added disabled: "start working on Netgear R8500"
  3b76c7cf0b ("bcm53xx: start working on Netgear R8500")

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[limit to subset of devices, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-30 21:48:38 +02:00
Adrian Schmutzler
bf5c56ba57 ath79: cosmetic fixes for partition node of D-Link DIR-825 B1
Make the node name match the reg property and remove the unused
DT label.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-30 21:43:56 +02:00
Daniel Golle
d1a8217d87 kernel: clean-up build-configurable kernel config symbols
Don't explicitely disable options in target/linux/generic/config-* if
they are already controlled in config/Config-kernel.in.
Add a bunch of new symbols  and prepare defaults for using only unified
hierarchy (ie. cgroup2). Update symbol dependencies while at it

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-07-30 16:59:47 +01:00
Luochongjun
68ac3f2cdd ath79: add support for gl-e750
The gl-e750 is a portable travel router that gives you safe access to
the internet while traveling.

Specifications:
- SoC: Qualcomm Atheros AR9531 (650MHz)
- RAM: 128 MB DDR2
- Flash: 16 MB SPI NOR (W25Q128FVSG) + 128 MB SPI NAND (GD5F1GQ4UFYIG)
- Ethernet: 10/100: 1xLAN
- Wireless: QCA9531 2.4GHz (bgn) + QCA9887 5GHz (ac)
- USB: 1x USB 2.0 port
- Switch: 1x switch
- Button: 1x reset button
- OLED Screen: 128*64 px

MAC addresses based on vendor firmware:
LAN *:a0 art 0x0
2.4GHz *:a1 art 0x1002
5GHz *:a2 art calculated from art 0x0 + 2

Flash firmware:
Since openwrt's kernel already exceeds 2MB, upgrading from the official
version of GL-inet (v3.100) using the sysupgrade command will break the
kernel image. Users who are using version 3.100 can only upgrade via
uboot. The official guidance for GL-inet is as follows:
https://docs.gl-inet.com/en/3/troubleshooting/debrick/

In the future, GL-inet will modify the firmware to support the sysupgrade
command, so users will be able to upgrade directly with the sysupgrade
command in future releases.

OLED screen control:
OLED controller is connected to QCA9531 through serial port, and can send
instructions to OLED controller directly through serial port.
Refer to the links below for a list of supported instructions:
https://github.com/gl-inet/GL-E750-MCU-instruction

Signed-off-by: Luochongjun <luochongjun@gl-inet.com>
[fix alphabetic sorting in 10-fix-wifi-mac, drop check-kernel-size]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 20:49:48 +02:00
Adrian Schmutzler
6da5356195 lantiq: disable default build for devices with 4M flash
It has been decided that the 19.07 release will be last one to include
4/32 devices.

This disables default build for all devices with 4M flash on lantiq.
Note that this will affect _all_ devices for amazonse ("ase") and
xway_legacy subtarget.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 12:08:16 +02:00
Adrian Schmutzler
55e2d5eb3b ath79: disable default build for devices with 4M flash
It has been decided that the 19.07 release will be last one to include
4/32 devices.

This disables default build for the remaining devices with 4M flash
on ath79. Note that this will leave exactly one enabled device for
ath79/tiny subtarget, PQI Air-Pen, which was moved there due to
kernel size restrictions.

All 4M TP-Link devices have already been disabled in
8819faff47 ("ath79: do not build TP-Link tiny images by default")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 12:08:16 +02:00
Adrian Schmutzler
01a3e891d7 ath79: reorganize common image definitions for Netgear
Netgear currently has a special definition for tiny devices, which
is only used by two devices. Despite, it sets ups the IMAGE/default
definition individually for all devices, although there is actually
only one exception.

This merges the common parts into a single netgear_generic definition
(in contrast to netgear_ath79_nand), and adjusts the individual
definitions accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 12:08:16 +02:00
David Bauer
c5360894dc rockchip: enable rockchip-thermal
Enable the rockchip-thermal driver to allow reading the temperature of
the SoC.

Tested on NanoPi R2S

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-29 01:40:20 +02:00
David Bauer
7a4fc8906c rockchip: distribute net interrupts
This adds a hotplug script for distributing interrupts of eth0 and eth1
across different cores. Otherwise the forwarding performance between
eth0 and eth1 is severely affected.

The existing SMP distribution mechanic in OpenWrt can't be used here, as
the actual device IRQ has to be moved to dedicated cores. In case of
eth1, this is in fact the USB3 controller.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
5a57a1ac1f arm64: dts: rockchip: Add txpbl node for RK3399/RK3328
Some rockchip SoCs like the RK3399 and RK3328 exhibit an issue
where tx checksumming does not work with packets larger than 1498.

The default Programmable Buffer Length for TX in these GMAC's is
not suitable for MTUs higher than 1498. The workaround is to disable
TX offloading with 'ethtool -K eth0 tx off rx off' causing performance
impacts as it disables hardware checksumming.

This patch sets snps,txpbl to 0x4 which is a safe number tested ok for
the most popular MTU value of 1500.

For reference, see https://lkml.org/lkml/2019/4/1/1382.

Signed-off-by: Carlos de Paula <me@carlosedp.com>
Link: https://lore.kernel.org/r/20200218221040.10955-1-me@carlosedp.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
6242ac4735 rockchip: enable LAN LED configuration
This enables the LEDs on the LAN interfaces.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
b7a9a183fb rockchip: add NanoPi R2S support
Hardware
--------
RockChip RK3328 ARM64 (4 cores)
1GB DDR4 RAM
2x 1000 Base-T
3 LEDs (LAN / WAN / SYS)
1 Button (Reset)
Micro-SD slot
USB 2.0 Port

Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.

MAC-address
-----------
The vendor code supports reading a MAC address from an EEPROM connected
via i2c0 of the SoC. The EEPROM (address 0x51) should contain the MAC
address in binary at offset 0xfa. However, my two units didn't come with
such an EEPROM soldered on. The EEPROM should be placed between the SoC
and the GPIO pins on the board. (U10)

Generating rendom MAC addresses works around this issue. Otherwise, all
boards running the same image have identical MAC addresses.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
b72f7c64a4 rockchip: allow for multiple boot-scripts
Add support for select a bootscript depending on the device built. This
is necessary, as the FriendlyARM NanoPi R2S needs a different bootcmd in
order to produce output on the debug UART.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
Adrian Schmutzler
bcd7a0c095 arc770: update kernel version to 5.4
Update config with make kernel_oldconfig and copy/refresh patch.

Add CONFIG_WATCHDOG_CORE=y to fix the following error as done for
several targets already:

 Package kmod-hwmon-sch5627 is missing dependencies for the following
 libraries:
 watchdog.ko

Directly switch to kernel 5.4.

This patch is compile-tested only. However, the target is essentially
pure upstream with a single patch, and it has been reported that
kernel 5.4 has been run on this target successfully already.

Note that in my local tests building with all packages/kmods failed
since openvswitch selects libunwind, which doesn't build for arc with
the following error:

checking if we should build libunwind-ptrace... yes
checking if we should build libunwind-setjmp... yes
checking for build architecture... x86_64
checking for host architecture... arc
checking for target architecture... arc
checking for target operating system... linux-gnu
checking for ELF helper width... configure: error: Unknown ELF target: arc
make[3]: *** [Makefile:65: /data/openwrt/build_dir/target-arc_arc700_uClibc/
   libunwind-1.3.1/.configured_68b329da9893e34099c7d8ad5cb9c940] Error 1

Deselecting all kmod-openvswitch* packages will have the build run through.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 20:15:10 +02:00
Adrian Schmutzler
88689da65f lantiq: fix cosmetic issues with partition offsets and sizes
This fixes a few cosmetic issues with partition offset and size
that are inconsistent probably due to copy/pasting.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 13:02:47 +02:00
Josh Bendavid
11bff24b3e ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.

Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
        WiFi 5G (white), USB 3.0 (white)

Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips

Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
  button, then re-plug it. Keep the reset button pressed until the power
  LED starts flashing orange, manually assign a static IP address under
  the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1

* Some modern browsers may have problems flashing via the Recovery GUI,
  if that occurs consider uploading the firmware through cURL:

    curl -v -i -F "firmware=@file.bin" 192.168.0.1

MAC addresses:

lan   factory 0xe000     *:EB (label)
wan   factory 0xe006     *:EE
2.4   factory 0xe000 +1  *:EC
5.0   factory 0xe000 +2  *:ED

Seems like vendor didn't replace the dummy entrys in the calibration data.

Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 12:37:07 +02:00
Adrian Schmutzler
8126e572dd imx6: use device-tree compatible for board name
In imx6, we currently use the model from DTS to derive a board name
manually in /lib/imx6.sh.

However, if we have individual DTS files anyway, we can exploit
generic 02_sysinfo and use the compatible as board name directly.

While at it, remove the wildcards from /lib/upgrade/platform.sh as
these might make code shorter, but are quite unpleasant when grepping
for a specific device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 12:10:45 +02:00
Adrian Schmutzler
0f3c3a5fb2 layerscape: harmonize device strings
OpenWrt lately has harmonized device (definition) names to the
pattern vendor_model to improve overall consistency, also with
other values like the DTS compatible.

This patch applies that scheme to the layerscape target.

Since this (intentionally) creates a bigger overlap between DTS names,
compatible, and device definition name, it also moves DEVICE_DTS and
SUPPORTED_DEVICES definitions to the Device/Default blocks.

Apart from that, it also modifies several packages to use consistent
naming in order to keep the $(1) file references working.

While at it, remove one layer of complexity for the setup in
tfa-layerscape package.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 12:06:52 +02:00
Adrian Schmutzler
a1eb2c4633 mvebu: only disable WRT1900AC v1 and WRT32X for buildbots
Use "DEFAULT := n" to only disable devices for buildbots, but
keep them available for manual build.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 11:05:25 +02:00
Jo-Philipp Wich
ac9730c495 mvebu: disable WRT1900AC v1 and WRT32X images for now
The kernel appears to have grown too large, breaking the build for the
entire target.

Disable the affected images for now until the situation is dealt with.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-07-26 18:58:22 +02:00
David Woodhouse
b36422b914 mediatek: mt7623: add full system image for UniElec U7623
This adds a full eMMC image including U-Boot, which means that the
kernel can inherit the true RAM size detected by the preloader.

As implemented in previous commits, sysupgrade to this image from
the legacy layout (and via that, from the vendor-installed image)
is supported.

Rename the legacy image for the 512MiB board, for clarity.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:08:31 +08:00
David Woodhouse
1113dcab05 mediatek: mt7623: rename gen_banana_pi_img.sh → gen_mtk_mmc_img.sh
As I buy more hardware and continue to work on consolidation, This will
apply to a lot of MediaTek platforms; rename it accordingly.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:08:21 +08:00
David Woodhouse
f5cebbe2e4 mediatek: mt7623: make gen_banana_pi_img.sh more generic
This actually covers fairly much all the MediaTek platforms; they
only have different images because they don't include the preloader
and U-Boot, and rely on preinstalled stuff from the vendor.

So this script can slowly take over the world as we complete the
support for various other platforms, starting with UniElec U7623…

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:08:21 +08:00
David Woodhouse
5787684cb4 mediatek: mt7623: add scatter file for unbricking with SP Flash Tool
Many MediaTek SoCs can be unbricked by using the SP Flash Tool from
http://spflashtool.com/ along with a "scatter list" file, which is
just a text file listing which image gets loaded where.

We use a trivial partition layout for the tool, with the whole eMMC
image as a single "partition", which means users just need to unzip
the sysupgrade image. Doing the real partition layout would be overly
complex and would require the individual partitions to be shipped
as artifacts — or users to extract them out of the sysupgrade image
just for the tool to put them adjacent to each other on the eMMC
anyway.

The tool does require a copy of the preloader in order to operate,
even when it isn't flashing the preloader to the eMMC boot region.
So drop that into the bin directory as an artifact too.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:07:52 +08:00
Chuanhong Guo
65fc47cac5 mediatek: mt7623: build lzma fit for bpi-r2
bpi-r2 images are shipped with mainline u-boot which can extract lzma
with no problem.
remove custom kernel recipe to build lzma fit image instead of
uncompressed fit with zboot.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-07-26 17:04:49 +08:00
David Woodhouse
29fa5526a2 mediatek: mt7623: prepare for full sysupgrade support on UniElec U7623
An upcoming commit will add a full system image for U7623 which will
contain the MBR partition table and U-Boot too.

That contrasts with the current image which only owns the eMMC from
sector 0xa00 onwards, and must start with a legacy uImage.

Prepare for sysupgrade to the new images, and cope with the fact that
the recovery partition will be /dev/mmcblk0p2 instead of /dev/mmcblk0p1
after the upgrade.

This commit could potentially be backported to 19.07 to allow for direct
sysupgrade to the new image layout.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:36 +08:00
David Woodhouse
7a1eaa446b mediatek: mt7623: increase flexibility of finding recovery partition
I'm about to change the layout of the images for UniElec U7623 so make it
find the recovery partition based on which the root partition is too.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:36 +08:00
David Woodhouse
ff8cc137fb mediatek: mt7623: fix Ethernet setup for TRGMII mode
This fixes the TX performance issues seen on MT7623 boards.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:36 +08:00
David Woodhouse
be3c8f8b2b mediatek: fix Ethernet support on UniElec U7623
The definition of the switch in the device-tree was not correct. Make it
look more like the Banana Pi R2, which works.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:35 +08:00
David Woodhouse
6eb63019af mediatek: mt7623: fix sysupgrade from vendor OpenWrt on UniElec U7623
This board ships with an ancient 14.07-based OpenWrt using block2mtd, and
the MBR partition table contains nonsense.

It is possible to sysupgrade to an upstream OpenWrt image, but the
legacy layout of the OpenWrt images start at 0xA00 in the eMMC, with
a raw uImage. The legacy OpenWrt image doesn't "own" the beginning
of the device, including the MBR and U-Boot.

This means that when a user upgrades to upstream OpenWrt, it doesn't
boot because it can't find the right partitions. So hard-code them on
the kernel's command line using CONFIG_CMDLINE_PARTITION (for block).

Additionally, the vendor firmware doesn't cope with images larger than
about 36MiB, because it only overwrites the contents of its "firmware"
MTD partition. The current layout of the legacy image wastes a lot of
space, allowing over 32MiB for the kernel and another 10MiB for the FAT
recovery file system which is only created as 3MiB. So pull those in
to allow 4¾ MiB for the kernel, 3MiB for recovery, and then we have over
20MiB for the root file system.

This doesn't affect the new images which ship with a full eMMC image
including a different MBR layout and a partition for U-Boot, because
our modern U-Boot can actually pass the command line to the kernel, and
the built-in one doesn't get used anyway.

Tested by upgrading from vendor OpenWrt to the current legacy image,
from legacy to itself, to the previous legacy layout, and then to
finally the full-system image.

This commit probably wants backporting to 19.07, which also doesn't
install over the vendor OpenWrt and doesn't even have a full-system
installation option.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:35 +08:00
David Woodhouse
ea9ef8c945 mediatek: mt7623: add explicit console= to U7623 kernel
The bootloader for legacy builds can't set it, so we end up unable to
log in on the serial port.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:35 +08:00
Leon M. George
15f585afc5 ath79: add support for Compex WPJ563
Specifications:

SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 Gigabit ethernet ports
3×3 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 24V passive or 36V-56V passive with optional IEEE 802.3af/at
USB 3.0 header

Installation:

To install, either start tftp in bin/targets/ath79/generic/ and use
the u-boot prompt over UART:

tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj563-squashfs-sysupgrade.bin
erase 0x9f680000 +1
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
boot

The cpximg file can be used with sysupgrade in the stock firmware (add
SSH key in luci for root access) or with the built-in cpximg loader.
The cpximg loader can be started either by holding the reset button
during power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.

For example, if the board is labelled '7A02':

tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj563-squashfs-cpximg-7a02.bin

MAC addresses:

<&uboot 0x2e010>  *:71  (label)
<&uboot 0x2e018>  *:72
<&uboot 0x2e020>  *:73
<&uboot 0x2e028>  *:74

Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.

Signed-off-by: Leon M. George <leon@georgemail.eu>
2020-07-26 02:14:45 +02:00
Aleksander Jan Bajkowski
f8ea7c53fd lantiq: xrx200: disable unused switch and phy
xrx200 has a 6 port built-in switch with 2 integrated PHY. None of the
xrx200 router uses external switch. Most boards use integrated or Lantiq
(Intel) PEF7071 PHY. Only some FritzBox routers use AT803X PHY and
VGV7510KW22 use ICPLUS PHY. Other unused PHY drivers may be removed.

This patch enables these symbols only on xway and xway_legacy subtargets:
 - CONFIG_PSB6970_PHY (Driver for PHY in PSB6970 - 7 port FE Switch)
 - CONFIG_RTL8366RB_PHY (Driver for PHY in RTL8366 - 6 port GE Switch)
 - CONFIG_RTL8366_SMI (Driver for RTL8366 - 6 port GE Switch)

Reduces image size by 7.3kB.

Continuation of 58a6f06978 (PR: #2983)

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[fix sorting in config files, small fix in commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-26 02:14:38 +02:00
Adrian Schmutzler
739d282c2f mediatek: remove condition in Device/Default
The current condition with part of the variables set dependent on
the subtarget in Device/Default isn't really nice to read and also
defeats the purpose of having a default node.

This removes the special settings for mt7623 and moves them to the
individual devices, which is not much of a problem as there are
actually just two of them and they partly use different settings
anyway.

While at it, slightly adjust the order of variables and wrap some
long lines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-25 23:19:19 +02:00
Bjoern Dobe
d38d345c72 ath79: mikrotik: use base mac on lan for RBwAPG-5HacT2HnD
The Mikrotik RBwAPG-5HacT2HnD has only a single ethernet interface
(lan), and the vendor uses the base (label) MAC address for it.

Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>
[commit title/message improvement]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-25 22:01:34 +02:00
Sungbo Eo
ab78694fe8 treewide: rename POWER_ON_STRIP register
AR8327 datasheet[1] calls the register at address 0x0010
"Power-on Strapping Register". As it has nothing to do with "strip",
let's rename it to "POWER_ON_STRAP" to make it easier to grasp.

[1] https://lafibre.info/images/doc/201106_spec_AR8327.pdf

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-25 21:50:50 +02:00
John Thomson
8484d6da1e ramips: remove non-existant poe_passthrough for RouterBOARD 750Gr3
This 750gr3 GPIO17 switch was added based on vendor source,
but only the 760iGS (which shares the rbsysfs board identifier)
device has the physical wiring. The 750Gr3 actually does not
support PoE out.

Apart from that, note that the gpio base (480) would have required
this GPIO to be referenced as 497 if it was kept.

Fixes: 6ba58b7b02 ("ramips: cleanup the RB750Gr3 support")

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-25 21:41:07 +02:00
Davide Fioravanti
92780d80ab ramips: add support for Winstars WS-WN583A6
The Winstars WS-WN583A6 is a wireless repeater with 2 gigabit ethernet
ports. Even if mine is branded as "Gemeita AC2100", the sticker on the
back says WS-WN583A6. So I will refer to it as Winstars WS-WN583A6.
Probably the real product name is the Wavlink WL-WN583A6 because of
the many references to Wavlink in the OEM firmware and bootlog.

Hardware
--------
SoC:   Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM:   128MB
FLASH: 8MB NOR (GigaDevice GD25Q64B)
ETH:   2x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
  - 2.4GHz: 1x MT7603E (2x2:2)
  - 5GHz:   1x MT7615E (4x4:4)
  - 6 internal antennas
BTN:
  - 1x Reset button
  - 1x WPS button
  - 1x ON/OFF switch (working but unmodifiable)
  - 1x Auto/Schedule switch (working but unmodifiable. Read Note #3)
LEDS:
  - 1x White led
  - 1x Red led
  - 1x Amber led
  - 1x Blue led
  - 2x Blue leds (lan and wan port status: working but unmodifiable)
UART:
  - 57600-8-N-1

Everything works correctly.

Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.

Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on M83A6.V5030.191210 firmware version.

1) Go to http://192.168.10.1/webcmd.shtml

2) Type the following line in the "Command" input box:
	mkdir /etc_ro/lighttpd/www/dev; for i in /dev/mtd*ro; do dd if=${i} of=/etc_ro/lighttpd/www${i}; done

3) Click "Apply"

4) After few seconds, in the textarea should appear this output:
		16384+0 records in
	16384+0 records out
	8388608 bytes (8.0MB) copied, 4.038820 seconds, 2.0MB/s
	384+0 records in
	384+0 records out
	196608 bytes (192.0KB) copied, 0.095180 seconds, 2.0MB/s
	128+0 records in
	128+0 records out
	65536 bytes (64.0KB) copied, 0.032020 seconds, 2.0MB/s
	128+0 records in
	128+0 records out
	65536 bytes (64.0KB) copied, 0.031760 seconds, 2.0MB/s
	15744+0 records in
	15744+0 records out
	8060928 bytes (7.7MB) copied, 3.885280 seconds, 2.0MB/s
	dd: can't open '/dev/mtd5ro': No such device
	dd: can't open '/dev/mtd6ro': No such device
	dd: can't open '/dev/mtd7ro': No such device

   Excluding the "X.XXXXXX seconds" part, you should get the same
   exact output. If your output doesn't match mine, stop reading
   and ask for help in the forum.

5) Open the following links to download the partitions of the OEM FW:
	http://192.168.10.1/dev/mtd0ro
	http://192.168.10.1/dev/mtd1ro
	http://192.168.10.1/dev/mtd2ro
	http://192.168.10.1/dev/mtd3ro
	http://192.168.10.1/dev/mtd4ro

   If one (or more) of these files weight 0 byte, stop reading and ask
   for help in the forum.

6) Store these downloaded files in a safe place.

7) Reboot your router to remove any temporary file from your router.

Installation
------------
Flash the initramfs image in the OEM firmware interface.
When openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.

Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) The "System Command" page allows to run every command as root.
   For example you can use "dd" and "nc" to backup the OEM firmware.
   PC (SERVER):
	nc -l 5555 > ./mtdXro
   ROUTER (CLIENT):
	dd if=/dev/mtdXro | nc PC_IP_ADDRESS 5555

2) The OEM web interface accepts only images containing the string
   "WN583A6" in the filename.
   Currently the OEM interface accepts only the initramfs image
   probably because it checks if the ih_size in the image header is
   equal to the whole image size (instead of the kernel size)
   Read more here:
   https://forum.openwrt.org/t/support-for-strong-1200/22768/19

3) The white led (namely "Smart Night Light") can be controller by the
   user only if the side switch is set to "Schedule" otherwise it will
   be activated by the light condition (there is a photodiode on the
   top side of the router)

4) Router mac addresses:

   LAN		XX:XX:XX:XX:XX:8F
   WAN		XX:XX:XX:XX:XX:90
   WIFI 2G	XX:XX:XX:XX:XX:91
   WIFI 5G	XX:XX:XX:XX:XX:92

   LABEL	XX:XX:XX:XX:XX:91

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove chosen node, fix whitespace]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-25 21:04:11 +02:00
Adrian Schmutzler
1e55df2e41 oxnas: use vendor_model scheme for ox810se
Most newer targets have been converted to consistently use
vendor_model scheme for device definitions/image names, ox820 is
using it as well, so let's just convert ox810se for consistency.

While at it, use generic setup for DEVICE_DTS and add SUPPORTED_DEVICES.
The latter have been introduced for ox820 already in
cf7896117b ("oxnas: enable image metadata by setting SUPPORTED_DEVICES")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-25 21:04:11 +02:00
Hauke Mehrtens
64de3076c3 lantiq: Fix warning in SPI driver
This fixes a warning in the SPI driver at bootup. This warning is seen
in kernel 5.4 on lantiq deives.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-23 23:39:56 +02:00
Phi Nguyen
eda9751d86 ipq40xx: support reset button for WPJ419
Compex WPJ419 has a reset button on a GPIO pin.

Signed-off-by: Phi Nguyen <phind.uet@gmail.com>
2020-07-23 12:56:58 +02:00
Adrian Schmutzler
b057862e24 Revert "ramips: fix flash layout for TP-Link TL-WR841N v14"
This reverts commit 1623defbdb.

As already stated in the reverted patch, the OEM firmware will
properly recreate the config partition if it is overwritten by
OpenWrt.

The main reason for adding the partition was the image size
restriction imposed by the 0x3d0000 limitation of the TFTP
flashing process. Addressing this by shrinking the firmware
partition is not a good solution to that problem, though:

1. For a working image, the size of the content has to be smaller
   than the available space, so empty erase blocks will remain.

2. Conceptually, the restriction is on the image, so it makes sense
   to implement it in the same way, and not via the partitioning.
   Users could e.g. do initial flash with TFTP restriction with
   an older image, and then sysupgrade into a newer one, so TFTP
   restriction does not apply.

3. The (content) size of the recovery image is enforced to 0x3d0000
   by the tplink-v2-image command in combination with
   TPLINK_FLASHLAYOUT (flash layout in mktplinkfw2.c) anyway.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-22 18:59:44 +02:00
Adrian Schmutzler
0a5d74fa68 arc770: use generic 02_sysinfo
Currently arc770 sets a board name from compatible for no apparent
reason. Just use the compatible directly instead.

This theoretically removes a board name "generic" when no compatible
was present, however, there is no case where this "generic" board
name was actually used.

This also fixes an issue where snps,axs101 would not have been
properly detected anyway, as its case was not set up syntactically
correct.

Fixes: 576621f1e3 ("linux: add support of Synopsys ARC770-based boards")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-22 18:28:09 +02:00
Adrian Schmutzler
3c190ef112 archs38: use generic 02_sysinfo
Currently archs38 sets a board name from compatible for no apparent
reason. Just use the compatible directly instead.

This theoretically removes a board name "generic" when no compatible
was present, however, there is no case where this "generic" board
name was actually used.

This also fixes an issue where snps,axs103 would not have been
properly detected anyway, as its case was not set up syntactically
correct.

Fixes: 73015c4cb3 ("linux: add support of Synopsys ARCHS38-based boards")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-22 18:28:09 +02:00