In fixing ipq8074 WAX630 dts, there was a typo in the switch lan bmp.
Fix it to fix compilarion error.
Fixes: f3cd4bfb7f ("ipq807x: fix multiple error on ESS switch port define")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix multiple error on ESS switch port define.
- Fix wrong switch CPU and WAN bmp define. (many times wan port are
actually set in lan mask and lan port in wan mask)
- Renumber phyinfo port, use port_id instead of phy_address as it
doesn't make sense using that for port enumeration
- Drop additional port for devices that have them not connected.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
ISISC is the QCA codename for their Atheros switch family including
AR237, QCA8337 etc.
Since we have qca8k support in OpenWrt, there is no need to have SSDK
support for these switches, and boards that also have external switches
can just use qca8k.
Disable QCA803x PHY support as well, since all of those are supportable
via at803x driver.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add issue labeler action. This action will parse BUG issue from the
template and will make validation on the insert data.
The action will:
- Tag the issue with SNAPSHOT or release based on the provided release
- Tag the issue with the reported tag
- Tag the issue with the image kind (Official or Self Built)
- Validate the reported version exist
- Validate the reported release exist
- Validate the reported device exist
Will also tag the issue with useful tag or flag the issue as invalid.
Will also comment the issue with the invalid info provided.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add release info to BUG template. Having the reported release is an
additional info to better bisect the bug and what release is affected.
This is also useful in preparation for action that will parse BUG
template and add tag and do validations.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add new function to dump-targer-info.pl to DUMP devices provided a
matching target/subtarget.
Example:
./scripts/dump-targer-info.pl devices ipq806x/generic
will produce the sorted list of devices defined in the following format:
device_id device_name
Devices may have alternative names, the script will dump each
alternative name in the same line of device_id.
Following the pattern:
device_id "PRIMARY DEVICE NAME" "ALT0 DEVICE NAME" "ALT1 DEVICE NAME" ...
Example:
tplink_ad7200 "TP-Link AD7200 v1/v2" "TP-Link Talon AD7200 v1/v2"
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Those devices have Ethernet interfaces using base MAC address increased
by 0x40 in the 3rd indexed byte (00:00:00:FF:00:00). To describe that we
were using a custom (downstream) "mac-address-increment-byte" property.
The same result can be achieved by using "mac-base" with a properly
adjusted offset value (0x40 << 16). It may be not pretty but it should
work without custom property or downstream kernel patch to support it.
Cc: Ansuel Smith <ansuelsmth@gmail.com>
Cc: Catrinel Catrinescu <cc@80211.de>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rosen Penev <rosenp@gmail.com>
There was a typo in the LED definition for the mode of non-standard
qca8k LEDs. Mode for link speed was wrongly set to link-10 link-100
link-1000 while the real mode in sysfs is link_10 link_100 and
link_1000.
Fix the entry to the correct mode.
Fixes: c707cff6c9 ("ipq806x: add LEDs definition for non-standard qca8k LEDs")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
PTP and swconfig support in SSDK require kernel modifications we dont need
nor we want to support for now, so move the PTP and swconfig disablement
into general build options as they are not ipq807x specific.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Recent SSDK versions started also parsing the "SoC" variable to identify
the SoC along with the "CHIP_TYPE".
We are not passing "SoC" currently and this leads to components we dont
need like MHT (New 2.5G quad port switch) being compiled and then unused,
so lets just pass the "SoC" as well.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Every board in qualcommax is using the same BM and TM switch tick modes, so
instead of specifying them in each board lets just set them in the ESS DTSI
directly.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that we have the MAC modes defined in DT bindings, lets replace all of
the raw hex values with defines.
While we are here, we can drop the disabled UNIPHY-s as that is the default
value in the ESS DTSI.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Every board that has the switch enabled needs to have MAC modes defined for
all 3 UNIPHY instances.
So, instead of having to at least put the disabled MAC mode for UNIPHY-s
let disable them by default and then boards can override it.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since every board needs to define the correct MAC modes, it makes sense
to document the allowed hex values with a humanly readable name.
So, lets document all of the allowed MAC modes from SSDK 12.4 as bindings,
so later we can replace all of the hex values in DTS-es with these.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 7ceb76ca3a.
Python 3.12 removes the distutils package and is therefore not
compatible. We have to check downstream what relies on distutils before
adding actual support for Python 3.12. Sorry for the noise.
With this in-place, the macOS CI job fails and turns things red, revert
for now.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The RTW88 PCI/USB driver uses the same firmware,
so add firmware dependencies.
Also CI report that:
Package kmod-rtw88-usb is missing dependencies for the following libraries:
usbcore.ko
This commit fixes it.
Fixes: 3538a19 ("mac80211: split rtw88 configuration for each supported chip")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
New gdb has got libzstd support, and libzstd gets detected
at buildbot build. Explicitly disable it to avoid dependency.
Fixes: f79de8ec65 ("gdb: Update to 13.2")
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Commit 947b44d ("ipq807x: fix wrong define for LAN and WAN ess mask")
started fixing wrong switch_lan_bmp that defined lan there weren't
actually present. This displayed a fragility in the malibu phy init code
in qca-ssdk.
Add patch to fix this. Also update each DTS with the new required
property if needed.
The new binding malibu_phy_start_addr is required with devices that
place the malibu first PHY referring port1 on a different PHY addres
than 0. The most common configuration is 0 but some device (for example
Qnap 301W) place the malibu PHY at an offset to address 16.
Refer to ipq8074-ess dtsi for extensive description on how to derive
this value.
Quoting the patch detailed description:
The usage of first_phy_addr is EXTREMELY FRAGILE and results
in dangerous results if the OEM (or anyone that by chance try to
implement things in a logical manner) deviates from the default values
from the "magical template".
To be in more details. With QSDK 12.4, some tweaks were done to improve
autoneg and now on every call of port status, the phydev is tried to
add. This resulted in the call and log spam of an error with ports that
are actually not present on the system with qsdk reporting phydev is
NULL. This itself is not an error and printing the error is correct.
What is actually an error from ages is setting generic bitmap reporting
presence of port that are actually not present. This is very common on
OEM where the switch_lan_bmp is always a variant of 0x1e (that on bitmap
results in PORT1 PORT2 PORT3 PORT4 present) or 0x3e (PORT1 PORT2 PORT3
PORT4 PORT5). Reality is that many device are used as AP with one LAN
port or one WAN port. (or even exotic configuration with PORT1 not
present and PORT2 PORT3 PORT4 present (Xiaomi 3600)
With this finding one can say... ok nice, then lets update the DT and
set the correct bitmap...
Again world is a bad place and reality is that this cause wonderful
regression in some case of by extreme luck the first ever connected
port working and the rest of the switch dead.
The problem has been bisected to all the device that doesn't have the
PORT1 declared in any of the bitmap.
With this prefaction in mind, on to the REAL problem.
malibu_phy_hw_init FOR SOME REASON, set a global variable first_phy_addr
to the first detected PHY addr that coincidentally is always PORT1.
PORT1 addr is 0x0. The entire code in malibu_phy use this variable to
derive the phy addrs in some function.
Declaring a bitmap where the PORT1 is missing (or worse PORT4 the only
one connected) result in first_phy_addr set to 1 or whatever phy addr is
detected first setting wrong value all over the init stage.
To fix this, introduce a new binding malibu_first_phy_addr to manually
declare the first phy that the malibu PHY driver should use and permit
to detach it from port bmp detection. The legacy detection is kept for
compatibility reason.
Fixes: #13945
Fixes: 947b44d9ae ("ipq807x: fix wrong define for LAN and WAN ess mask")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com> # Qnap 301W
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 8cce00bc9d.
The confusion was real and this change cause regression on other
advanced devices that makes actual use of the first_phy_addr value.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some local patches have been sent to upstream and they are slightly
different from the upstream version. So it's better to replace them
to avoid conflicts with the new mac80211 backport driver. The
different parts have been merged into patch 996.
This commit also includes some additional fixes:
* Fix watchdog function.
* Improve MT7620 register initialization.
* Introduce DMA busy watchdog for rt2800.
P.S.
Sometimes rt2800 series chips may fall into a DMA busy state. The
tx queues become very slow and the client cannot connect to the AP.
Usually, We can see a lot of hostapd warnings at this point:
'hostapd: IEEE 802.11: did not acknowledge authentication response'
The DMA busy watchdog can help the driver automatically recover
from this abnormal state. By the way, setting higer 'cell_density'
and disabling 'disassoc_low_ack' can significantly reduce the
probability of the DMA busy.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Kernel 6.1 has introduced support for RTW8822BU network adapter, which
is an USB variant of the rtw8822b 802.11ac chipset family.
Build and install the corresponding module in the rtw88 package
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Current rtw88 build configuration builds modules for all chips supported by
rtw88 driver family. This brings the following issues:
- adding a chip with a different bus is not convenient (all chips currently
depends on PCI)
- some features requirements are not relevant for all chips in family (eg
802.11AC is enforced but RTW88-8723DE is only a 802.11b/g/n chip)
Remove those constraints/issues by adding one module build option per
supported chip, and add intermediate options to properly cascade
dependencies.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Device specification:
- MT7629 with 16MB NOR flash W25Q128 and 128 MB DDR3 RAM.
- MT7761N and MT7762N wireless chips (currenlty no driver in OpenWrt available)
- WiFi is NOT working on this device
- Dual core but second CPU doesn't seem to work (Error message during boot: "CPU1: failed to come online")
There are two similar merge requests for similar devices with the same issues:
- https://github.com/openwrt/openwrt/pull/12286
- https://github.com/openwrt/openwrt/pull/5084
UART interface is next to the reset button, pinout:
- 1: TX (the pin with the arrow marker)
- 2: RX
- 3: GND
- 4: VCC
UART settings: 115200,8n1, 3.3V
U-Boot menu can be entered by pressing Ctrl+B during startup.
Booting initramfs:
- Set your computers IP adress to 192.168.1.110
- Run a TFTP server providing the initramfs image
- Power on the AP, press Ctrl+B to get to the U-Boot menu
- Select "1. System Load Linux to SDRAM via TFTP"
- Update kernel file name, input server IP and input device IP (if they deviate from the defaults)
- After booting, create a backup of all partitions, especially for kernel and root_fs. They are required for reverting back to stock firmware
- The sysupgrade image can be flashed now
MAC adresses:
- LAN and 2.4GHz use the same MAC (the one printed on the device)
- 5GHz WiFi MAC is LAN MAC + 1
GPIOs:
- GPIO 21 is the reset pin (low active)
- GPIO 55 is for the green LED (active high)
- GPIO 56 is for the yellow/amber LED (active high)
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Specification:
- MT7622BV SoC with 2.4GHz wifi
- MT7975AN + MT7915AN for 5GHz
- MT7531BE Switch
- 512MB RAM
- 128 MB flash
- 3 LEDs (red, orange, white)
- 2 buttons (WPS and Reset)
MAC addresses:
- WAN MAC is stored in partition "Odm" at offset 0x83
- LAN (as printed on the device) is WAN MAC + 1
- WLAN MAC (2.4 GHz) is WAN MAC + 2
- WLAN MAC (5GHz) is WAN MAC + 3
Disassembly: Remove 4 screws in the bottom and 2 screws in the top (after removing the blue cover on the top), then the board can be pulled out.
The pins for the serial console are already labeled on the board (VCC, TX, RX, GND). Serial settings: 3.3V, 115200,8n1
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.25
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the status LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-a1-squashfs-recovery.bin
Flashing via uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-initramfs-kernel.bin. You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later
- Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.25
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the status LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util M32 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware 1.03.01_HOTFIX: ./m32-firmware-util M32 --DecryptFactoryImage M32-REVA_1.03.01_HOTFIX.enc.bin M32-REVA_1.03.01_HOTFIX.decrypted.bin
Revert back to stock using uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides the previously created backup of the Kernel1 partition. You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to FLASH will start. After a few seconds the stock firmware should start again
There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-m32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP. It can be used if no backup of the Kernel1 partition is reuqired.
Flahsing via OEM web interface is currently not possible, the OEM images are encrypted and require a specific memory layout which is not compatible to the partition layout of OpenWrt.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
If /root is created with too permissive permissions, then sshd won't
trust the contents of /root/.ssh as being adequately protected.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
ath9k-htc USB-based adapters also support 5/10MHz channel bandwidth.
Move the code handling the features in debugfs to common-debug.c,
and create proper registration functions to use in debug.c and
htc_drv_debug.c, leaving only debugfs registration there.
While at that, refresh one patch that would conflict otherwise.
Tested on TP-Link Archer C7v2 (ath79) and TP-Link WN722Nv1 (AR9287)
and WN822Nv2 (AR7010+AR9287).
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
ath9k-htc USB-based adapterssupport 5/10MHz channel bandwidth, the
same as standard ath9k ones.
Move the code handling the features in debugfs to common-debug.c,
and create proper registration functions to use in debug.c and
htc_drv_debug.c, leaving only debugfs registration there.
While at that, refresh one patch that would conflict otherwise.
Tested on TP-Link Archer C7v2 (ath79) and TP-Link WN722Nv1 (AR9287)
and WN822Nv2 (AR7010+AR9287).
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
With the case of asking an invalid version that is too big, getver.sh
might return an invalid output in the form of HEAD~-2260475641.
This is caused by BASE_REV - GET_REV using a negative number.
Prevent this by checking if BASE_REV - GET_REV actually return 0 or a
positive number and set REV variable accordingly. With the following
change, invalid revision number will result in unknown printed instead
of the invalid HEAD~-NUMBERS output.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In-kernel driver for MCS7715 USB-serial bridge has a bool option,
enabling support for parallel port on that chip - which is tied to the
same kernel module. Enable it and select kmod-ppdev, as the image size
increase is minimal and the package isn't bundled in the images by
default.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This fixes a well known "LZMA ERROR 1" error on Sercomm NA502,
reported on the OpenWrt forum. [1]
[1]: https://forum.openwrt.org/t/176942
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
creates SGE encrypted factory images
to use via the D-Link web interface
rename the old factory unencrypted images to recovery
for use in the recovery console when recovery is needed
DIR-1935-A1 , DIR-853-A1 , DIR-853-A3 , DIR-867-A1 ,
DIR-878-A1 and DIR-882-A1
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Since kernel 5.11, the PXA I2C driver has been converted to generic I2C
recovery, which makes the I2C bus completely lock up if recovery pinctrl
is present in the DT and I2C recovery is enabled.
This effectively completely broke I2C on Methode uDPU and eDPU boards
as both of them rely on I2C recovery.
After a discussion upstream, it was concluded that there is no simple fix
and that the blamed upstream commit:
0b01392c18b9993a584f36ace1d61118772ad0ca ("i2c: pxa: move to generic GPIO
recovery") should be reverted.
I have sent the revert upstream, it should be merged soon so lets "fix"
OpenWrt as well.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Adjust our local ath10k-ct patches to the change
from the -ct 6.2 version to 6.4.
This restores e.g. the LED functionality.
Fixes: 7d3651f1b9 ("ath10k-ct: switch to 6.4")
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Commit 947b44d9ae ("ipq807x: fix wrong define for LAN and WAN ess mask")
started fixing wrong switch_lan_bmp that defined lan there weren't
actually present. This displayed a fragility in the malibu phy init code
in qca-ssdk.
Add patch to fix this.
Quoting the patch detailed description:
I'm very confused by this and to me it's not clear the real usage of
this logic.
From what I can see the usage of this is EXTREMELY FRAGILE and results
in dangerous results if the OEM (or anyone that by chance try to
implement things in a logical manner) deviates from the default values
from the "magical template".
To be in more details. With QSDK 12.4, some tweaks were done to improve
autoneg and now on every call of port status, the phydev is tried to
add. This resulted in the call and log spam of an error with ports that
are actually not present on the system with qsdk reporting phydev is
NULL. This itself is not an error and printing the error is correct.
What is actually an error from ages is setting generic bitmap reporting
presence of port that are actually not present. This is very common on
OEM where the switch_lan_bmp is always a variant of 0x1e (that on bitmap
results in PORT1 PORT2 PORT3 PORT4 present) or 0x3e (PORT1 PORT2 PORT3
PORT4 PORT5). Reality is that many device are used as AP with one LAN
port or one WAN port. (or even exotic configuration with PORT1 not
present and PORT2 PORT3 PORT4 present (Xiaomi 3600)
With this finding one can say... ok nice, then lets update the DT and
set the correct bitmap...
Again world is a bad place and reality is that this cause wonderful
regression in some case of by extreme luck the first ever connected
port working and the rest of the switch dead.
The problem has been bisected to all the device that doesn't have the
PORT1 declared in any of the bitmap.
With this perfection in mind, on to the REAL problem.
malibu_phy_hw_init FOR SOME REASON, set a global variable first_phy_addr
to the first detected PHY addr that coincidentally is always PORT1.
PORT1 addr is 0x0. The entire code in malibu_phy use this variable to
derive the phy addrs in some function.
Declaring a bitmap where the PORT1 is missing (or worse PORT4 the only
one connected) result in first_phy_addr set to 1 or whatever phy addr is
detected first setting wrong value all over the init stage.
To fix this, just drop this variable and hardcode everything to assume
the first phy adrr is ALWAYS 0 and remove calculation and use define for
special case.
With the following change normal switch traffic is restored and ports
function is recovered.
Fixes: #13945
Fixes: 947b44d9ae ("ipq807x: fix wrong define for LAN and WAN ess mask")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Information about package license is important, so lets add it.
Fixes: 79ee0d2cee ("debugcc: add new package to debug IPQ based SoC clocks")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
I find myself manually compiling dtc as a staticly linked binary rather
often while porting a new device to OpenWrt as dtc is rarely included in
various vendor modifications of OpenWrt.
So, since dtc offers a convenient meson option to build it as staticaly
linked binary, lets make it a compile time option.
Signed-off-by: Robert Marko <robimarko@gmail.com>
switch_lan_bmp and switch_wan_bmp have wrong values and now cause
problems with the new version of the qca-ssdk.
Fix the wrong entry and drop the redundant switch_cpu_bmp.
Also introduce some convenient define to better understand values in
this map.
Fixes: eea264fead ("kernel: qca-ssdk: update to 12.4")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com> # Dynalink AX3600 and Qnap 301W
Reviewed by: Robert Marko <robimarko@gmail.com>
