Commit Graph

120 Commits

Author SHA1 Message Date
Adrian Schmutzler
0bf4d681d4 ramips: allow JCG_MAXSIZE in kiB in Build/jcg-header
This allows JCG_MAXSIZE to be specified in kilobytes. This makes
this value more consistent and easier comparable with other size
variables.

This also changes the only occurence of the variable, for Cudy WR1000.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-13 19:43:30 +01:00
Adrian Schmutzler
e4155bcc45 ramips: fix TARGET_DEVICES after UniElec rename
Device node names were updated, but updating TARGET_DEVICES
was overlooked.

Fixes: 4408723d42 ("ramips: remove RAM size from device name
for UniElec devices")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 18:36:45 +02:00
Adrian Schmutzler
4408723d42 ramips: remove RAM size from device name for UniElec devices
UniElec devices are the last ones in ramips target still having
the RAM size in device name although RAM size is auto-detected.

Remove this from device name, compatible, etc., as it's not
required and might be misleading to users and developers adding
device support copying those devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:27:30 +02:00
Adrian Schmutzler
b376818f97 ramips: harmonize device vendor Zbtlink
Spelling of Zbtlink varies across image definitions and DTS files.

This patch uses Zbtlink consistently and also updates the model
in DTS files to contain the vendor in all cases.

This patch is cosmetical, as there should be no dependencies on
device model name in ramips anymore.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-29 00:08:20 +02:00
Sungbo Eo
b7ec6659a1 ramips: add support for ipTIME A3
ipTIME A3 is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.

Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
  - Switch: SoC internal
- UART:
  - J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-09-25 14:44:36 +08:00
Ivan Hörler
c03a328b10 ramips: add SD-Card support for Linkit Smart 7688
The Linkit Smart 7688 has a SD-Card reader that does not work with the official build of openwrt. Adding kmod-sdhci-mt7620 makes it working.

Signed-off-by: Ivan Hörler <i.hoerler@me.com>
2019-09-15 20:34:09 +02:00
Chuanhong Guo
7a21c85f70 ramips: improve support for Xiaomi Miwifi Nano
This patch does the following things:
1. mark u-boot-env writable
2. add bootcount support
   Currently, u-boot has a flag_boot_success env variable to reset.
   Also reset it in our firmware to follow the behavior in vendor's
   firmware.
3. disable usb support
   This router doesn't have usb port at all.
4. increase spi clock to 40MHz
5. fix pinmux groups

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-09-04 19:26:01 +08:00
Paul Spooren
149d1e7a61 ramips/mt76x8: add DEVICE_VENDOR for tl-wr840n-v5
DEVICE_VENDOR is missing for this device.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-08-22 12:57:34 +02:00
Sungbo Eo
2678ba9093 ramips: add support for ipTIME A604M
ipTIME A604M is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.

Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7612EN
- Ethernet: 5x 10/100Mbps
  - Switch: SoC internal
- UART:
  - J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-08-17 23:52:34 +08:00
DENG Qingfang
d3e832d6fd ramips: add support for HiWiFi HC5761A
HiWiFi HC5761A is an "MT7628AN variant" of HC5761

Specifications:
- MediaTek MT7628AN 580MHz
- 128 MB DDR2 RAM
- 16 MB SPI Flash
- 2.4G MT7628AN 802.11bgn 2T2R 300Mbps
- 5G MT7610EN 802.11ac 433Mbps
- 3x 10/100 Mbps Ethernet

Flash instruction:
1. Get SSH access to the router
2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one
3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP
4. Run `mtd write /tmp/<filename> firmware`
5. reboot

Known bug:
- SD slot does not work (See PR 1500)

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-08-08 21:02:03 +08:00
Adrian Schmutzler
9d87a58d34 ramips: remove ralink_default_fw_size_xxx variables
There are frequent examples of the ralink_default_fw_size_xxx
variables being used to "roughly" set flash size without caring
about the actual size of the firmware partition.

To discourage this behavior, this patch removes the variables and
just sets IMAGE_SIZE by its numeric value for each target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:30 +02:00
Adrian Schmutzler
363197311b ramips: remove default IMAGE_SIZE for ramips target
Currently, ramips target defines 0x7b0000 as default IMAGE_SIZE
for all devices in ramips target, i.e. this will be set if a
device does not specify IMAGE_SIZE itself.

From 92 devices using that default due to a "missing" IMAGE_SIZE,
14 were incorrect by a small amount (i.e. still "8M" flash) and
12 were completely off ("16M", "4M", ...).

This patch thus removes the _default_ IMAGE_SIZE and defines
IMAGE_SIZE for each device individually. This should indicate to
people supporting new devices that this parameter has to be cared
about.

For the present code, this patch is cosmetical.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:27 +02:00
Adrian Schmutzler
439435f59b ramips/mt76x8: fix IMAGE_SIZE for all devices
This fixes IMAGE_SIZE for all devices based on the partition size
given in DTS:

DEVICE                       *.MK   *.DTS     VERDICT
alfa-network_awusfree1       (8M)   0x7b0000
buffalo_wcr-1166ds           -      0x7c0000  wrong
cudy_wr1000                  (8M)   0x7b0000
d-team_pbr-d1                (16M)  0x0fb0000
duzun_dm06                   -      0x7b0000  default
glinet_gl-mt300n-v2          16064k 0xfb0000
glinet_vixmini               7872k  0x7b0000
hilink_hlk-7628n             (32M)  0x1fb0000
hiwifi_hc5661a               (16M)  0xf70000  wrong
hiwifi_hc5861b               15808k 0xf70000
mediatek_linkit-smart-7688   (32M)  0x1fb0000
mediatek_mt7628an-eval-board (4M)   0x7b0000  wrong
mercury_mac1200r-v2          -      0x7c0000  wrong
netgear_r6120                15744k 0xf60000
onion_omega2                 (16M)  0xfb0000
onion_omega2p                (32M)  0x1fb0000
rakwireless_rak633           -      0x7b0000  default
skylab_skw92a                16064k 0xfb0000
tama_w06                     15040k 0xeb0000
totolink_lr1200              7872k  0x7b0000
tplink_archer-c20-v4         7808k  0x7a0000
tplink_archer-c50-v3         7808k  0x7a0000
tplink_archer-c50-v4         7616k  0x770000
tplink_tl-mr3020-v3          7808k  0x7a0000
tplink_tl-mr3420-v5          7808k  0x7a0000
tplink_tl-wa801nd-v5         7808k  0x7a0000
tplink_tl-wr802n-v4          7808k  0x7a0000
tplink_tl-wr840n-v4          7808k  0x7a0000
tplink_tl-wr840n-v5          3904k  0x3d0000
tplink_tl-wr841n-v13         7808k  0x7a0000
tplink_tl-wr841n-v14         3968k  0x3e0000
tplink_tl-wr842n-v5          7808k  0x7a0000
tplink_tl-wr902ac-v3         7808k  0x7a0000
unielec_u7628-01-128m-16m    16064k 0xfb0000
vocore_vocore2               (16M)  0xfb0000
vocore_vocore2-lite          (16M)  0x7b0000  wrong
wavlink_wl-wn570ha1          (8M)   0x7b0000
wavlink_wl-wn575a3           (8M)   0x7b0000
widora_neo-16m               (16M)  0x0fb0000
widora_neo-32m               (32M)  0x1fb0000
wiznet_wizfi630s             (32M)  0x1fb0000
wrtnode_wrtnode2p            (16M)  0x1fb0000 wrong
wrtnode_wrtnode2r            (16M)  0x1fb0000 wrong
xiaomi_mir4a-100m            14976k 0xea0000
xiaomi_miwifi-nano           (16M)  0xfb0000
zbtlink_zbt-we1226           (8M)   0x7b0000
zyxel_keenetic-extra-ii      14912k 0xe90000

No verdict means that the device is correctly set.

Legend:
( ): Value is set via ralink_default_fw_size_xxM
[ ]: Value is derived from parent definition
 - : Value is not set and derived from default definition

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:15 +02:00
Adrian Schmutzler
7392af7520 ramips: fix ralink_default_fw_size_16M
In ramips, there are the following predefined values for IMAGE_SIZE
ralink_default_fw_size_4M    3866624   3776k   0x3B0000
ralink_default_fw_size_8M    8060928   7872k   0x7B0000
ralink_default_fw_size_16M  16121856  15744k   0xF60000
ralink_default_fw_size_32M  33226752  32448k  0x1FB0000

Out of those, the "16M" value is obviously odd, as it provides more
room for the remaining partitions than the tree others.
Of the devices in all subtargets, there are actually > 50 that have
a firmware partition with 0xFB0000 size, while only 5 (!) have
0xF60000. From the former, many are set to
ralink_default_fw_size_16M anyway, although it is wrong at the
present point.

Consequently, it makes sense to change ralink_default_fw_size_16M
to 0xFB0000, and to update IMAGE_SIZE for the 5 devices with
0xF60000.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:01 +02:00
Adrian Schmutzler
447deed52a ramips: Sort all subtarget Makefiles
This patch applies sorting to the definitions as whole blocks.

Sorting has been performed fully automatic, line count differences
originate from double empty lines removed.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
b97a99256f ramips/mt76x8: Name DTS files based on scheme
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
c2334ad60d ramips/mt76x8: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
d93969a13a ramips: Improve compatible for TP-Link Archer devices
Include "Archer" in compatible as it is part of the device name.

Update Makefile device names where necessary to match compatible.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:28 +02:00
Daniel Golle
ee66fe4ea9 ramips: convert DEVICE_TITLE to new variables
Also unify naming and add details where they were missing.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-07-06 14:58:03 +02:00
Alexander Müller
3fd97c522b
ramips: add support for TP-Link TL-WR841n v14
TP-Link TL-WR841n v14 is a router based on MediaTek MT7628N.

- MediaTek MT7628NN
- 32 MB of RAM
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet

Installation:
- copy the
  'openwrt-ramips-mt76x8-tl-wr841n-v14-squashfs-tftp-recovery.bin'
  file to your tftp server root and rename it to 'tp_recovery.bin'.
- configure your PC running the TFTP server with the static IP address
  192.168.0.66/24
- push the reset button and plug in the power connector. Wait until
  the orange led starts blinking (~6sec)

Signed-off-by: Alexander Müller <donothingloop@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu> [small modifications gpio-hog]
2019-07-02 16:17:49 +02:00
Chuanhong Guo
0ab9f283f7 ramips: add support for TOTOLINK LR1200
Specifications:
- SoC: MT7628DAN (MT7628AN with 64MB built-in RAM)
- Flash: 8M SPI NOR
- Ethernet: 5x 10/100Mbps
- WiFi: 2.4G: MT7628 built-in
        5G: MT7612E
- 1x miniPCIe slot for LTE modem (only USB pins connected)
- 1x SIM slot

Flash instruction:
U-boot has a builtin web recovery page:
1. Hold the reset button while powering it up
2. Connect to the ethernet and set an IP in 192.168.1.0/24 range
3. Open your browser and upload firmware through http://192.168.1.1

Note about the LTE modem:
If your router comes with an EC25 module and it doesn't show up
as a QMI device, you should do the following to switch it to QMI
mode:
1. Install kmod-usb-serial-option and a terminal software
   (e.g. minicom or screen). All 4 serial ports of the modem
   should be available now.
2. Open /dev/ttyUSB3 with the terminal software and type this
   AT command: AT+QCFG="usbnet",0
3. Power-cycle the router. You should now get a QMI device
   recognized.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-05 10:26:33 +02:00
Markus Scheck
5ff5c9bce6 ramips: add support for Xiaomi Mi Router 4A (100M Edition)
- SoC:      MediaTek MT7628AN
- Flash:    16MB (Winbond W25Q128JV)
- RAM:      64MB
- Serial:   As marked on PCB, 3V3 logic, baudrate is 115200
- Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN)
- WIFI0:    MT7628AN 2.4GHz 802.11b/g/n
- WIFI1:    MT7612EN 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs:     Programmable power-LED (two-colored, yellow/blue)
            Non-programmable internet-LED (shows WAN-activity)
- Buttons:  Reset

INSTALLATION:

1. Connect to the serial port of the router and power it up.
   If you get a prompt asking for boot-mode, go to step 3.
2. Unplug the router after
       > Erasing SPI Flash...
       > raspi_erase: offs:20000 len:10000
   occurs on the serial port. Plug the router back in.
3. At the prompt select option 2 (Load system code then
   write to Flash via TFTP.)
4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the
   Server-IP.
5. Connect your computer to LAN1 and assign it as 192.168.1.2/24.
6. Rename the sysupgrade image to test.bin and serve it via TFTP.
7. Enter test.bin on the serial console and press enter.

Signed-off-by: Markus Scheck <markus@mscheck.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added mt76 compatible]
2019-05-31 11:21:22 +02:00
Davide Fioravanti
7c91144ae6 ramips: add CUDY WR1000 support
Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas

Specifications:

MT7628 (580 MHz)
64 MB of RAM (DDR2)
8 MB of FLASH
2T2R 2.4 GHz (MT7628)
2T2R 5 GHz (MT7612E)
3x 10/100 Mbps Ethernet (2 LAN + 1 WAN)
2x external, non-detachable antennas (5dbi)
UART header on PCB (57600 8n1)
7x LED, 2x button

Known issues:
The Power LED is always ON, probably because it is connected
directly to power.

Flash instructions
------------------
Load the ...-factory.bin image via the stock web interface.

Openwrt upgrade instructions
----------------------------
Use the ...-sysupgrade.bin image for future upgrades.

Revert to stock FW
------------------
Warning! This tutorial will work only with the following OEM FW:
  WR1000_EU_92.122.2.4987.201806261618.bin
  WR1000_US_92.122.2.4987.201806261609.bin
If in the future these firmwares will not be available anymore,
you have to find the new XOR key.

1) Download the original FW from the Cudy website.

   (For example WR1000_EU_92.122.2.4987.201806261618.bin)

2) Remove the header.

   dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64

3) XOR the new file with the region key.

   FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D
   FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C

   You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this:

   xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767..

   Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!):
   https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false)

4) Check the resulting decrypted image.

   Check if bytes from 0x20 to 0x3f are:
   4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00

   Alternatively, you can use u-boot's tool dumpimage tool to check
   if the decryption was successful. It should look like:

   # dumpimage -l stock-firmware.bin
   Image Name:   Linux Kernel Image
   Created:      Tue Jun 26 10:24:54 2018
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    4406635 Bytes = 4303.35 KiB = 4.20 MiB
   Load Address: 80000000
   Entry Point:  8000c150

5) Flash it via forced firmware upgrade and don't "Keep Settings"

   CLI: sysupgrade -F -n stock-firmware.bin

   LuCI: make sure to click on the "Keep settings" checkbox
         to disable it. You'll need to do this !TWICE! because
         on the first try, LuCI will refuse the image and reset
	 the "Keep settings" to enable. However a new
         "Force upgrade" checkbox will appear as well.
         Make sure to do this very carefully!

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added wifi compatible, spiffed-up the returned to stock instructions]
2019-05-31 10:36:36 +02:00
Jan Hoffmann
2fdd02cc7c ramips: add factory image for WNDR3700v5
This uses the existing rules for Sercomm factory images and moves them
to the ramips image Makefile, so they can be used in all subtargets.

The new factory image for WNDR3700v5 can be flashed using nmrpflash.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2019-05-18 16:44:41 +02:00
Liu Yu
671c9d16e3 ramips: add support for HILINK HLK-7628N
Specification:

CPU:       MT7628 580 MHz. MIPS 24K
RAM:       128 MB
Flash:     32 MB
WIFI:      802.11n/g/b 20/40 MHz
Ethernet:  5 Port ethernet switch
UART:      2x

Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART0 line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
   set device and tftp server IP address and input the firmware
   file name. U-boot will then load the firmware and write it into
   the flash.
5. After firmware is started connect via ethernet at 192.168.1.1

Signed-off-by: Liu Yu <f78fk@live.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed dupped subject]
2019-05-18 13:43:55 +02:00
David Bauer
a4dc519888 ramips: fix R6120 factory image
The factory firmware omits the JFFS2 end-marker while flashing via
web-interface. Add a 64k padding after the marker fixes this problem.

When the end-marker is not present, OpenWRT won't save the overlayfs
after initial flash.

Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-05-11 16:37:11 +02:00
Eike Feldmann
9e0fb5a27f ramips: add support for Rakwireless RAK633
It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or
Vocore2.

Specification:

CPU:       MT7628 580 MHz. MIPS 24K
RAM:       64 MB
Flash:     8 MB
WIFI:      802.11n/g/b 20/40 MHz
USB:       1x Port USB 2.0
Ethernet:  5 Port ethernet switch
UART:      2x

Installation: Use the installed uboot Bootloader. Connect a serial cable
to serialport 0. Turn power on.  Choose the option: "Load system code
then write to Flash via TFTP".  Choose the local device IP and the TFTP
server IP and the file name of the system image.  After if the
Bootloader will copy the image to the local flash.

Notes: The I2C Kernel module work not correctly. You can send and
receive data. But the command i2cdetect doesn’t work. FS#845

Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com>
[commit subject and message touches, DTS whitespace fixes, wifi LED
rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses,
removed i2c kernel modules]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-14 23:42:03 +02:00
David Bauer
43e8c37cb4 ramips: add support for GL.iNet VIXMINI
Hardware
--------
SoC:   MediaTek MT7628NN
RAM:   64M DDR2 (Etron EM68B16CWQD-25H)
FLASH: 8M (Winbond W25Q64JVSIQ)
LED:   Power - WLAN
BTN:   Reset
UART:  115200 8N1
       TX and RX are labled on the board as pads next to the SoC

Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
   Note: The ethernet port is by default WAN. So you need to connect to
   the router via WiFi

2. Navigate to the Update tab on the left side.

3. Select "Local Update"

4. Upload the OpenWrt sysupgrade image.
   Note: Make sure you select not to preserve the configuration.

Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
   Wait for the LED to flash 5 times.

2. Assign yourself a static IPv4 in 192.168.1.0/24

3. Upload the OpenWrt sysupgrade image at 192.168.1.1.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-13 18:46:40 +02:00
Tobias Welz
7c4b85ee27 ramips: add support for WIZnet WizFi630S board
The WIZnet WizFi630S board is in the miniPCIe form factor.

SoC: Mediatek MT7688AN
RAM: 128MB
Flash: 32Mb
WiFi: 2.4GHz
Ethernet: 3x 100Mbit
USB: 1 (USB 2.0)
serial ports: 2 (1x full, 1xlite)

Flash and recovery instructions: Use the factory installed u-boot boot
loader. It is available on UART2 (115200,8,n,1).  Then get the
sysupgrade image from a tftp server.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
[whitespace and device name in makefile fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:33:59 +00:00
Marcel Jost
e6f047fa36 ramips: add TP-Link TL-WR802N-v4 support
This patch adds support for the TP-Link TL-WR802N-v4.
https://openwrt.org/toh/tp-link/tl-wr802n

Specification:
- MT7628N (580 MHz)
- 64 MB RAM
- 8 MB FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet
- 1x LED

Flash instruction:

The only way to flash the image in TL-WR802N v4 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 10 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Marcel Jost <majo@icutech.ch>
2019-02-28 11:26:10 +01:00
Thomas Vincent-Cross
a915ad8464 ramips: use generic board detection for Wavlink WL-WN575A3
Bring Wavlink WL-WN575A3 in line with other Wavlink ramips devices.

Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
2019-02-28 11:26:10 +01:00
David Bauer
01dcd574a2 ramips: add support for Archer C50 v4
This adds support for the TP-Link Archer C50 v4.
It uses the same hardware as the v3 variant, sharing the same FCC-ID.

CPU:   MediaTek MT7628 (580MHz)
RAM:   64M DDR2
FLASH: 8M SPI
WiFi:  2.4GHz 2x2 MT7628 b/g/n integrated
WiFI:  5GHz 2x2 MT7612 a/n/ac
ETH:   1x WAN 4x LAN
LED:   Power, WiFi2, WiFi5, LAN, WAN, WPS
BTN:   WPS/WiFi, RESET
UART:  Near ETH ports, 115200 8n1, TP-Link pinout

Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.

Download a TP-Link image from their Wesite and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:

TP-Link image:             tpl.bin
OpenWRT sysupgrade image:  owrt.bin

 > dd if=tpl.bin of=boot.bin bs=131584 count=1
 > cat owrt.bin >> boot.bin

Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.

Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.

Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.

The boot.bin can now be uploaded and flashed using the web-recovery.

Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)

 > dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
 > dd if=tpl.bin of=tmp.bin bs=131584 count=1
 > dd if=tmp.bin of=boot.bin bs=512 skip=1
 > cat boot.bin >> tp_recovery.bin
 > cat owrt.bin >> tp_recovery.bin

Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.

Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.

U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.

Dual U-Boot
-----------
This is the first TP-Link MediaTek device to feature a split-uboot
design. The first (factory-uboot) provides recovery via TFTP and HTTP,
jumping straight into the second (firmware-uboot) if no recovery needs
to be performed. The firmware-uboot unpacks and executed the kernel.

Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5. Stock-firmware sets a flag in the "romfile" partition
before beginning to write and removes it afterwards. If the router boots
with this flag set, bootloader will automatically start Web-recovery and
listens on 192.168.0.1. This way, the vendor-firmware or an OpenWRT
factory image can be written.

By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.

It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 21:46:32 +01:00
David Bauer
915fbd4e31 ramips: adjust Netgear R6120 model name
Adjust the model string and device title to match other Netgear routers
in the ramips target.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 10:41:03 +01:00
Mathias Kresin
26a016731d firmware-utils: mksercommfw: overhaul image creation
Move the zip compression into a build recipe. Pad the image using the
existing build recipes as well to remove duplicate functionality

Change the code to append header and footer in two steps. Allow to use a
fixed filename as the netgear update image does.

Use a fixed timestamp within the zip archive to make the images
reproducible.

Due to the changes we are now compatible to the gnu89 c standard used by
default on the buildbots and we don't need to force a more recent
standard anymore.

Beside all changes, the footer still looks wrong in compare to the
netgear update image.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-15 19:11:54 +01:00
Chen Minqiang
295b37d207 ramips: mt76x8: select only the matching mt76 driver
Select the matching mt76 driver for the PCI wireless of the following
devices:

 - HiWiFi HC5861B
 - Mercury MAC1200R v2.0
 - Netgear AC1200 R6120
 - Buffalo WCR-1166DS
 - ZyXEL Keenetic Extra II
 - Wavlink WL-WN575A3

Because every device has selected the corresponding mt76 driver, we can
include kmod-mt7603 instead of the mt76 metapackage, which used for the
wireless of the mt7628 and mt7688 WiSoC.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
[select kmod-mt7603 as target default package, add wireless driver for
WL-WN575A3]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 12:17:25 +01:00
Chuanhong Guo
5563d49a39 ramips: disable sdhc for HC5661A
Currently OpenWrt doesn't support switching MT7628 into AP mode
(which is done by writing some undocumented registers in MTK SDK)
Without doing so, enabling SD breaks 4 FE ports and the SD controller
doesn't work since SD pins aren't configured correctly.

Disable SDHC on HC5661A to recover the 4 FE ports.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[drop the sdhci node completely]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 12:17:25 +01:00
Mathias Kresin
1977be8bd0 ramips: unifiy sysupgrade file extensions
Use .bin as file extension where possible. The user doesn't need to that
sysupgrade images for NAND boards are tarballs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-29 13:15:44 +01:00
Thomas Vincent-Cross
a160f50d4f ramips: add support for Wavlink WL-WN570HA1
This commit adds support for the Wavlink WL-WN570HA1, a dual-band PoE
wireless router with the following specifications:

 - CPU: MediaTek MT7688AN 580MHz
 - Flash: 8MB
 - RAM: 64MB
 - Ethernet: 1x 10/100Mbps
 - 2.4 GHz: 802.11b/g/n SoC, 1T1R, 27 dBm
 - 5 GHz: 802.11a/n/ac MT7610E, 1T1R, 25 dBm
 - Antennas: 2x external (1 per radio), detachable
 - LEDs: 3 programmable + Wi-Fi, WAN/LAN, Power
 - Buttons: Reset

Flashing instructions:

Factory U-boot launches a TFTP client if reset button is pressed during power-on.
Rename the sysupgrade file and configure TFTP as follows:

 - Client (WL-WN570HA1) IP: 192.168.10.101
 - Server IP: 192.168.10.100
 - Filename: firmware.bin

Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
[use generic board detection, add firmware partition compatible]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-28 00:50:35 +01:00
Mathias Kresin
8ec1a66c34 ramips: improve Skylab SKW92A support
Use the generic board detection instead of the target specific one as
all recent additions are doing.

Add the wireless led according the gpio number from the datasheet.
Rename the board part of the leds to match the name used for the
compatible string. Finally, do not hijack the wps led for boot status
indication longer than necessary.

Merge userspace config into existing cases.

Include the manufacture Name in the dts model string.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Russell Senior
e42327aa89 ramips: add support for Skylab SKW92A in EVB
Specifically, SKW92A_E16, described here:

  http://www.skylabmodule.com/wp-content/uploads/SkyLab_SKW92A_V1.04_datasheet.pdf

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x u.FL
- Power by micro-USB connector at USB1 on EVB
- UART via micro-USB connector at USB3 on EVB (57600 8n1)
- 5x Ethernet LEDs
- 1x WLAN LEDs
- 1x WPS LED connected by jumper wire from I2S_CK on J20 to WPS_LED pin hole next
  to daughter board on EVB
- WPS/Reset button (S2 on EVB)
- RESET button (S1 on EVB) is *not* connected to RST hole next to daughter board

Flash instruction:

>From Skylab firmware:

1. Associate with SKYLAP_AP
2. In a browser, load: http://10.10.10.254/
3. Username/password: admin/admin
4. In web admin interface: Administration / Upload Firmware, browse to
   sysupgrade image, apply, flash will fail with a message:
   Not a valid firmware. *** Warning: "/var/tmpFW" has corrupted data!
5. Telnet to 10.10.10.254, drops you into a root shell with no credentials
6. # cd /var
7. # mtd_write -r write tmpFW mtd4
   Unlocking mtd4 ...
   Writing from tmpFW to mtd4 ... [e]
8. When flash has completed, you will have booted into your firmware.

>From U-boot via TFTP and initramfs:

1. Place openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin on a TFTP server
2. Connect to serial console at USB3 on EVB
3. Connect ethernet between port 1 (not WAN) and your TFTP server (e.g.
   192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "1"
7. At u-boot prompts:
   Input device IP (10.10.10.123) ==:192.168.11.21
   Input server IP (10.10.10.3) ==:192.168.11.20
   Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin
8. Move ethernet to port 0 (WAN) on EVB
9. At new OpenWrt console shell, fetch squashfs-sysupgrade image and flash
   with sysupgrade.

>From U-boot via TFTP direct flash:

1. Place openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin on a TFTP server
2. Connect to serial console at USB3 on EVB (57600 8N1)
3. Connect ethernet between port 1 (not WAN) an your TFTP server (e.g.
   192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "2"
7. At u-boot prompts:
   Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
   Input device IP (10.10.10.123) ==:192.168.11.21
   Input server IP (10.10.10.3) ==:192.168.11.20
   Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin
8. When transfer is complete or as OpenWrt begins booting, move ethernet to
   port 0 (WAN).

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-11-26 09:47:27 +01:00
Daniel Golle
7c4251d881 ramips: select kmod-mt76x0e for TP-Link ArcherC20i and wr902ac-v3
Both devices come with a MediaTek MT7610E 5GHz 802.11ac 1T1R radio
which wasn't supported at the time the devices were added to OpenWrt.
Now that we got it, include kmod-mt76x0e in images for those devices.

Reported-by: Arian Sanusi <openwrt@semioptimal.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-11-25 15:24:49 +01:00
Koen Vandeputte
b4e17a7440 ramips: fix netgear r6120 factory image generation
as indicated in commit c5bf408ed6 "(ramips: fix image generation for mt76x8")
more rework was needed to fix the other issues.

Building on another machine, but using the same arch, showed
the application failing again for different reasons.

Fix this by completely rewriting the application, fixing following found issues:

- buffer overflows, resulting in stack corruption
- flaws in memory requirement calculations (too small, too large)
- memory leaks
- missing bounds checking on string handling
- non-reproducable images, by using unitilized memory in checksum calculation
- missing error handling, resulting in succes on specific image errors
- endianness errors when building on BE machines
- various minor build warnings
- documentation did not match the code actions (header item locations)
- allowing input to be decimal, hex or octal now

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-08 13:32:22 +01:00
Carlo Nel
6bbb220255 ramips: add support for TP-Link TL-MR3020 v3
TP-Link TL-MR3020 v3 is a pocket-size router based on MediaTek MT7628N.

This PR is based on the work of @meyergru[1], with his permission.

Specification:
- MediaTek MT7628N/N (575 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet

Flash instruction:

The only way to flash the image in TL-MR3020 v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-mr3020-v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

[1] https://github.com/meyergru/lede-source/commits/TL-MR3020-V3

Signed-off-by: Carlo Nel <carlojnel@gmail.com>
2018-09-06 21:36:42 +02:00
Deng Qingfang
d20f4fc628 ramips: add support for HiWiFi HC5861B
HiWiFi "Gee Enjoy1200" HC5861B is a dual-band router based on MediaTek MT7628AN
https://www.hiwifi.com/enjoy-view

Specifications:
- MediaTek MT7628AN 580MHz
- 128 MB DDR2 RAM
- 16 MB SPI Flash
- 2.4G MT7628AN 802.11bgn 2T2R 300Mbps
- 5G MT7612EN 802.11ac 2T2R 867Mbps
- 5x 10/100 Mbps Ethernet

Flash instruction:
1. Get SSH access to the router
2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one
3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP
4. Run `mtd write /tmp/<filename> firmware`
5. reboot

Everything is working

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-08-14 10:21:32 +02:00
Ludwig Thomeczek
5543d63fc8 ramips: add support for Netgear R6120
This patch adds support for the Netgear R6120, aka Netgear AC1200.

Specification:
- SoC: MediaTek MT7628 (580 MHz)
- Flash: 16 MiB
- RAM: 64 MiB
- Wireless: 2.4Ghz(builtin) and 5Ghz (MT7612E)
- LAN speed: 10/100
- LAN ports: 4
- WAN speed: 10/100
- WAN ports: 1
- Serial baud rate of Bootloader and factory firmware: 57600

To flash use nmrpflash with the provided factory.img.
Flashing via webinterface will not work, for now.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2018-08-13 08:37:19 +02:00
LoveSy
974a2b1aa9 ramips: mmc: Add SD card support to HC5661A
Tested on HC5661A and it now fixes the issue that when enabling sd card
in HC5661A, the wan and 3 lan ports will down.

Known issue:
- When enabling SD card support, the led light of system will down and the rest 2 lights keep working.

Signed-off-by: LoveSy <shana@zju.edu.cn>
2018-07-30 10:43:37 +02:00
Peter Lundkvist
33321ebefa ramips: TP-Link TL-WR902AC v3: don't build factory image
The line that produces factory image was accidentally left by me while
testing before inital commit.

I came to the conclusion that flashing from OEM firmware does not work
(seems to share this behavior with other tplinks based on mt7628).

I have not done any further analysis, as I was unable to open the
case and attach a serial port (too much glue). Maybe i will try once
more.

So the way to do initial flashing (or un-bricking) is to use the
tftp-recover image. It is possible to revert to OEM firmware with tftp
recovery; in this case the first 512 bytes the image file need to be
cut off.

Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
[add explaination provided via mail as commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-12 18:15:33 +02:00
Romain MARIADASSOU
ce31bdc20c ramips: add support for TL-WA801ND v5
Specification:

- System-On-Chip: MediaTek MT7628NN
- CPU/Speed: 580 MHz
- Flash-Chip: ELM Technology GD25Q64
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7628N 2.4GHz 802.11bgn

Currently the only method to install openwrt for the first time is via
TFTP recovery. After first install you can use regular updates.

Flash instructions:

1) To flash the recovery image, start a TFTP server with IP address
   192.168.0.66 and serve the recovery image named tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS and Reset
   button and power it up. Keep pressing the WPS/Reset button for
   10 seconds or until the lock LED is lighting up.
   It will try to download the recovery image and flash it.

It can take up to 2-3 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
2018-07-04 01:20:02 +02:00
Maxim Anisimov
7d07bc96b7 ramips: add support for ZyXEL Keenetic Extra II
Specification:
- System-On-Chip: MT7628N/N
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (57600 8n1)
- Wireless No1 (2T2R): SoC-integrated: MT7628N 2.4GHz 802.11bgn
- Wireless No2 (2T2R): On-board chip: MT7612EN 5GHz 802.11ac
- USB: Yes 1 x 2.0
- 4x LED, 3x button

The device supports dual boot mode. So we use only first half of flash.

Flash instruction:

The only way to flash OpenWrt image is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-zyxel_keenetic-extra-ii-squashfs-factory.bin"
   to "kextra2_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-07-04 01:20:02 +02:00
Maxim Anisimov
8956eb502d ramips: add support for TP-Link TL-WR842N v5
TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and
non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 7x LED, 2x button, power input switch

Flash instruction:

The only way to flash OpenWrt image in wr842nv5 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-06-16 10:08:51 +02:00
Mathias Kresin
d089a5d773 ramips: create image for mt7628 evb board
The image for the EVB board got lost with the merge of the mt7628 and
mt7688 subtargets.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-23 22:07:22 +02:00
Piotr Dymacz
68dcec7e16 ramips: image: drop redundant SUPPORTED_DEVICES
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-04-06 23:11:00 +02:00
Peter Lundkvist
d13b05741a ramips: add support for TP-Link TL-WR902AC v3
TP-Link TL-WR902AC v3 is a pocket-size dual-band (AC750) router
based on MediaTek MT7628N + MT7650E.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet

* MT7650 ac chip isn't not supported by LEDE/OpenWrt at the moment.
  Therefore 5Ghz won' work.

Flash instruction:

The only way to flash LEDE image in TL-WR902AC v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr902ac-v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
[drop p2led_an pinmux, this pin isn't used as gpio, fix whitespace issues]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-18 22:22:38 +01:00
Piotr Dymacz
f1c193c27e ramips: add support for ALFA Network AWUSFREE1
ALFA Network AWUSFREE1 is an USB Wi-Fi N300 adapter based on MT7628.

Specification:

- MT7628AN (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (MT7628) with external FEM (RFFM4203)
- 2x detachable antennas (RP-SMA)
- ASIX AX88772 USB to Ethernet bridge (connected with MT7628 PHY0)
- 4x LED (2 driven by GPIO)
- 1x button (reset)
- 1x mini USB for host and main power input
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:

1. Power device with reset button pressed and release it after ~5 sec.
2. Setup static IP 192.168.1.2/4 on your PC.
3. Go to 192.168.1.1 in browser and upload "sysupgrade" image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 23:40:11 +01:00
INAGAKI Hiroshi
e1d4aa36b0 ramips: add support for Tama W06
Tama Electric Axing W06 is a 2.4 GHz band 11n router, based on Mediatek
MT7688AN.

Specification:

- MT7688AN (575 MHz)
- 64 MB of RAM (DDR2 SDRAM)
- 16 MB of Flash (SPI)
- 1T1R 2.4 GHz
- 1x 10/100/1000 Mbps Ethernet
- 4x LEDs (GPIO connected: 3), 1x button
- 1x USB 2.0 Type-A (host)
- UART header on PCB (GND, RX, TX, Vcc from RJ45 side)

Flash instruction using sysupgrade image:
1. Connect micro-USB cable for power supply into W06 and turn on the
router
2. Connect to wifi with SSID "tama-*" with password. Complete SSID and
password are listed on the back of the router
3. Access to 192.168.1.1 and login with user name "admin" and password
empty
4. In firmware update(ファームウェア更新) page, click "参照" button
and click "ブラウザー" button to open file browser, select the
sysupgrade image and press OK button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-02-20 19:25:17 +01:00
Henryk Heisig
14951e8f8e ramips: add support for TP-Link Archer C50 v3
TP-Link Archer C50 v3 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7612E.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power switch

* WAN LED in this devices is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.

Flash instruction:

The only way to flash LEDE image in ArcherC50v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC50v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-02-11 16:04:16 +01:00
Daniel Golle
32f120b783 ramips: various fixes for zbt-we1226
Convert userspace code to use generic device-tree compatible board
detection method.  Users of the existing code will have to use
sysupgrade -F once to switch to the new generic board naming.
Properly setup pinctrl fixing the switch port LEDs.

Fixes commit 9c4fe103cb (ramips: add support for ZBT-WE1226)
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-02-06 03:00:33 +01:00
Jackson Ming Hu
21d3643828 ramips: add support for Widora Neo 32MB flash revision
Widora has updated their Widora Neo board recently.

The new model uses 32MB WSON-8 factor SPI flash
instead of the original 16MB SOP-8 factor SPI flash.

All the other hardware components are the same as
the first revision.

Detailed hardware specs listed below:

CPU: MTK MT7688AN
RAM: 128MB DDR2
ROM: 32MB WSON-8 factor SPI Flash (Winbond)
WiFi: Built-in 802.11n 150Mbps?
Ethernet: 10/100Mbps x1
Audio codec: WM8960
Other IO: USB OTG;
	  USB Power+Serial (CP2104);
	  3x LEDs (Power, LAN, WiFi);
	  2x Keys (WPS, CPU Reset)
	  1x Audio In/Out
	  1x IPEX antenna port
	  1x Micro SD slot

Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-23 23:31:09 +01:00
Mathias Kresin
a411881a40 ramips: add flash size postfix to Widora neo
Rename the Widora neo by adding a flash size prefix. Move the common parts
into a dtsi to be prepare everything for upcomming support of the 32MB
version.

Migrate the Widora neo to the generic board detection as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-23 23:31:09 +01:00
Daniel Golle
9c4fe103cb ramips: add support for ZBT-WE1226
MT7628NN (580MHz), 8MB SPI NOR, 64MB DDR2 RAM

Everything except for the switch LEDs works great.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-01-23 02:56:57 +01:00
Serg Studzinskii
eb58b14d27 ramips: tl-wr840n-v5: increase firmware partition for 4Mmtk layot
According to console log during TP-Link TL-WR840N v5 OEM firmware update
procedure 0x3e0000-0x3f0000 64kB "config" partition, which is used to store
router's configuration settings, is erased and recreated again during every
OEM firmware update procedure, thus does not contain any valuable factory data.
So it is conviniant to use this extra 64kB erase block for jffs overlay due
limited flash size on this device like it used on TP-Link's ar71xx boards.

Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
2018-01-18 08:04:18 +01:00
Maxim Anisimov
5bdd238b63 ramips: add support for TP-Link Archer C20 v4
TP-Link Archer C20 v4 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch

* WAN LED in this devices is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
  work.

Flash instruction:

The only way to flash LEDE image in ArcherC20v4 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC20v4-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-01-15 21:45:43 +01:00
Henryk Heisig
39e9bfb181 ramips: add support for TP-Link TL-MR3420 v5
TP-Link TL-MR3420 v5 are simple N300 router with
5-port FE switch and non-detachable antennas.
Its very similar to TP-Link TL-WR841N V13.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 8x LED, 2x button, power input switch

Flash instruction:

The only way to flash LEDE image in mr3420v5 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-mr3420-v5-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-12-23 15:35:52 +01:00
Mathias Kresin
8ca650b8ce ramips: move common tplink image build code into own recipe
Move common tplink image build code into own recipe. Include the common
parts instead of including a full build recipe and overwriting former set
varaibles.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-23 15:35:52 +01:00
Luis Araneda
575178e462 treewide: add only one device when appending to TARGET_DEVICES
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-12 18:47:26 +01:00
Piotr Dymacz
fa36bea470 ramips: add support for UniElec U7628-01
UniElec U7628-01 is a router platform board based on MediaTek MT7628AN.
The device has the following specifications:

- MT7628AN (580MHz)
- 64/128/256 MB of RAM (DDR2)
- 8/16 MB of flash (SPI NOR)
- 5x 10/100 Mbps Ethernet (MT7628 built-in switch)
- 1x 2T2R 2.4 GHz Wi-Fi (MT7628)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x miniSIM slot
- 1x microSD slot
- 1x USB 2.0 port
- 7x single-color LEDs (GPIO-controlled)
- 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe)
- 1x reset button
- 1x UART header (4-pins)
- 1x SDXC/GPIO header (10-pins, connected with microSD slot)
- 1x DC jack for main power (12 V)

The following has been tested and is working:

- Ethernet switch
- miniPCIe slot (tested with modem and Wi-Fi card)
- miniSIM slot
- sysupgrade
- reset button
- USB 2.0 port*

Due to a missing driver (MMC over GPIO) this is not supported:

- microSD card reader

* Warning:
USB buses in miniPCIe and regular A-type socket are connected together,
without any proper analog switch or USB HUB.

Installation:

This board might come with a different firmware versions (MediaTek SDK,
PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can
install LEDE using sysupgrade. Just SSH to the router and perform forced
sysupgrade (due to a board name mismatch). The default IP of this board
should be: 192.168.1.1 and username/password: root/admin. In case of a
different firmware, you can use web based recovery described below.

Use the following command to perform the sysupgrade (for the 128MB
RAM/16MB flash version):

sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin

Recovery:

This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.

SDXC/GPIO header (J3):

 1. SDXC_D3  / I2C_SCLK
 2. SDXC_D2  / I2C_SD
 3. SDXC_D1  / I2S_DI
 4. SDXC_D0  / I2S_WS
 5. SDXC_CMD / I2S_CLK
 6. SDXC_CLK / GPIO0
 7. SDXC_CD  / UART_RXD1
 8. UART_TXD1
 9. 3V3
10. GND

Other notes:

1. The board is available with different amounts of RAM and flash. We
have only added support for the 128/16 MB configuration, as that seems
to be the default. However, all the required infrastructure is in place
for making support for the other configurations easy.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-11-14 22:36:46 +01:00
Robert Marko
d0ef27594a ramips: add support for TP-Link TL-WR840N v5
TP-Link TL-WR840N v5 is simple N300 router with 5-port FE switch and
non-detachable antennas, based on MediaTek MT7628NN (aka MT7628N) WiSoC.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 1x LED (GPIO-controlled), 1x button

* LED in TL-WR840N v5 is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.
  Orange LED is registered so you can later use it for your own purposes.

  Flash instruction:

  Unlike TL-WR840N v4 flashing through WEB UI works in v5.
  1. Download lede-ramips-mt76x8-tl-wr840n-v5-squashfs-sysupgrade.bin image.
  2. Go to 192.168.0.1
  3. Flash the sysupgrade image through Firmware upgrade section of WEB UI.
  4. Wait until green LED stops flashing and use the router.

Notes:
TFTP recovery is broken since TP-Link reused bootloader code for v4 and
that does not take into account only 4 MB of flash and bricks the device.
So do not use TFTP Recovery or you will have to rewrite SPI flash.
They fixed it in later GPL code,but it is unknown which version of
bootloader you have.

After manually compiling and flashing bootloader from GPL sources TFTP
recovery works properly.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-11-08 23:25:05 +01:00
Alexander Couzens
b73986a826
ramips/mt76x8: add initramfs support for tplink 841n v13
The tplink 841n v13 requires an tplink v2 image header in
front of an initramfs image.

To boot an initramfs image:
- break the uboot by holding the '4' key
- setup your tftp server 192.168.0.255
- tftp 81000000 lede-ramips-mt76x8-tl-wr841n-v13-initramfs-kernel.bin
- bootm

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-10-09 17:34:41 +02:00
Thibaut VARÈNE
254061ee97 build: add mktplinkfw2 hardcoded values to makefile
This patch adds all the board-specific values currently hardcoded
in mktplinkfw2.c back to the respective device declarations in the
makefiles.

The rationale is to avoid modifying the source code every time a
new board or board variant is added.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2017-10-06 08:28:41 +02:00
L. D. Pinney
3e36ca4b43 ramips: merge mt7628/mt7688 into mt76x8
The ramips subtargets of mt7628 and mt7688 dts files all #include "mt7628an.dtsi"

They are essentially a single subtarget.

This patch merges the ramips subtargets mt7628 and mt7688 into a single subtarget mt76x8.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
2017-08-30 17:05:10 +02:00