I-O DATA WN-DX2033GR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : Raw NAND 128 MiB (Macronix MX30LF1G18AC-TI)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 2T2R, MediaTek MT7603E
- 5 GHz : 4T4R, MediaTek MT7615
- Ethernet : 5x 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC)
- LEDs/Keys : 2x/3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J5: 3.3V, TX, RX, NC, GND from triangle mark
- 57600n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs image:
1. Boot WN-DX2033GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
to perform firmware update
4. On the initramfs image, download the sysupgrade.bin image to the
device and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing
Notes:
- The hardware of WN-DX2033GR and WN-AX2033GR are almost the same, and
it is certified under the same radio-wave related regulations in Japan
- The last 0x80000 (512 KiB) in NAND flash is not used on stock firmware
- stock firmware requires "customized uImage header" (called as "combo
image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't
- uImage magic ( 0x0 - 0x3 ) : 0x434F4D42 ("COMB")
- header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
- image name (0x20 - 0x37) : model ID and firmware versions
- data length (0x38 - 0x3b) : kernel + rootfs
- data crc32 (0x3c - 0x3f) : kernel + rootfs
- There are 2x important flags in the flash:
- bootnum : select os partition for booting (persist, 0x4)
- 0x01: firmware
- 0x02: firmware_2
- debugflag : allow interrupt kernel loader, it's named as "Z-LOADER"
(Factory, 0xFE75)
- 0x00: disable debug
- 0x01: enable debug
MAC addresses:
LAN : 50:41:B9:xx:xx:90 (Factory, 0xE000 (hex) / Ubootenv, ethaddr (text))
WAN : 50:41:B9:xx:xx:92 (Factory, 0xE006 (hex))
2.4 GHz : 50:41:B9:xx:xx:90 (Factory, 0x4 (hex))
5 GHz : 50:41:B9:xx:xx:91 (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
GPIOs > 31 require special handling. This patch fixes both the
initialisation and direction get/set operations.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Add additional header information required for newer
bootloaders found on DIR-2660-A1 & A2.
Also remove the MTD splitter compatible from the second firmware
partition, as OpenWrt only supports handling of the first one.
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
[rephrase commit message, remove removal of read-only flags]
Signed-off-by: David Bauer <mail@david-bauer.net>
In hostapd_ubus_add_bss(), ubus objects are not registered for mesh
interfaces. This provokes a segfault when accessing the ubus object in
mesh deinit.
This commit adds the same condition to hostapd_ubus_free_bss() for
discarding those mesh interfaces.
Signed-off-by: Jesus Fernandez Manzano <jesus.manzano@galgus.net>
The rockchip platform supports squashfs SD card images. However, the
resulting image is not padded to completely fill the rootfs partition.
Because of that, the f2fs overlay might not be erased, resulting in
uci-defaults not bing executed or the configuration not being erased,
even though drop config was selected.
Modify the image generation process so the image is padded to cover the
entire root filesystem partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
The new `pkgmanifestjson` call prints all package manifest of a feed in
JSON format. This function can be used to print an overview of packages
information used for downstream tooling.
The script is entirely based on Petrs work on dependency visualisation.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Remove use of DEVICE_TITLE in favor of the
DEVICE_VENDOR and DEVICE_MODEL as used by
all other targets.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Remove use of DEVICE_TITLE in favor of the
DEVICE_VENDOR and DEVICE_MODEL as used by
all other targets.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
The `mkdir` commands supports passing multiple arguments to batch create
multiple folders, instead of calling the tool every single time.
If the creation of one of the folders fails, all other folder are still
created and therefore doesn't change the error handling.
Also stop creating `/etc/` explicitly after subfolders of `/etc/` were
already created.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The `sed`-script shouldn't be called multiple times, especially not with
the same files.
This commit merges all files together in a single `sed`-script call.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Using `make info` show the current target, revision, default packages
and available profiles. This commits adds the used architecture.
Signed-off-by: Paul Spooren <mail@aparcar.org>
For some reason, the build system chops off the last number from the version,
which is not correct. Add it back.
Update hash.
Fixes: 96c7164acd ("restool: update to LSDK-20.12")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[add Fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The official Plasma Cloud firmware adjusted the BDFs to contain new
conformance test limits and target power values. These should be imported
to avoid emissions outside the allowed limits.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Meraki wrote the ethernet MAC-address of the device
onto the eeprom (AT24C64) at the fixed location 0x66
to 0x6C. Let's fetch it from there.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
broke support for Meraki MR32 and this patch makes the replacement
configurable allowing for specifying the @ or - or whatever character
that is desired to retain backwards compatibility with existing devices.
For example, this patch includes the fix for the Meraki MR32 in
target/linux/bcm53xx/image for meraki_mr32:
DEVICE_DTS_DELIMITER := @
DEVICE_DTS_CONFIG := config@1
Fixes: 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Signed-off-by: Damien Mascord <tusker@tusker.org>
[Added tags, checkpatch.pl fixes, noted that this is for old stuff]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This breaks the package builds using the SDK.
The targets all build fine, but the package builder fails on many
packages. The package builder uses the OpenWrt SDK.
This reverts commit c377d874be.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Handle gcc and linux with a special regex that set their progname with
their major version. This way every minor version can be cleared. The
build cleanup logic can be tweaked later to clean the entire toolchain
and target dir with a different gcc version.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[reformat commit message]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Regex xxx-YYYY-MM-DD-GIT_SHASUM was missing. Add the new regex to improve
and better find outdated package. This also fix a bug where some bug were
incorrectly detected as packagename-yyyy-mm-dd instead of packagename due
to them be parsed by the wrong parser
Example:
openwrt-keyring-2021-02-20-49283916.tar.xz
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[added example in commit message]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Currently, the fstab service starts after the log service which breaks
the ability to write a persistent log file to a filesystem mounted by
the fstab service. Thus, change the start order of the fstab service so
it starts right before the log service.
Fixes: b131853 ("ubox: update to latest git revision")
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
[set to 11 to be explicitly before log, not only alphabetically, SPDX]
Signed-off-by: Paul Spooren <mail@aparcar.org>
This patch never went upstream so remove it. GCC should already add such
a check to the common functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove GLOB_ONLYDIR patch. Only fstools relies on it. fstools has been
fixed separately.
Remove woresize.h file. It seems to be for an old version of GCC.
Remove features.h and glibc-types files. Same as above.
Remove sys/cdefs.h. This is a deprecated header. Patches to fix packages
that use it have already been patched.
Tested with all packages in the base tree. They all compile.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This release introduces 64-bit time_t, which is needed to avoid the
year 2038 problem.
Remove upstream patches. Refreshed others.
Rebased features.h file based on latest musl.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Fixes compilation with GCC11.
Kept PKG_VERSION as there's some bug that chops off the 12 at the end.
Refreshed other patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Fixes compilation with both GCC 10 and 11.
Switched to AUTORELEASE for simplicity.
Removed PKG_VERSION as it's derived from PKG_SOURCE_VERSION.
Removed all patches as they are upstream backports.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
With GCC11, memcpy doesn't work here as it assumes a size of 0. Use
ioremap to avoid it.
Fixed parameter type to match board_get_mac_address.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This line should have been removed in 244847da "build: remove GCC9
support" but stayed in tree after an incomplete rebase. Fix it.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Delete tunnel on 6rd interface teardown.
Should solve problem related to tunnel stuck on restart loop
with "Unknown Command" on tunnel restart due to wan connection drop.
This patch is similar to the one written by Ansuel on Aug 2, 2021
but the 6rd teardown produces the same symptoms when the network
service is restarted.
Signed-off-by: David Lam <david@thedavid.net>
GCC 10 defaults to `-fno-common` and complains about multiple definition
of `mc_status` in restool.
Backport a patch from upstream to fix compilation with host GCC 10.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
c62d85cf7a0d bridge: check port bpdu filter status and apply it to the config
25555611be91 libnetlink: turn rtnetlink error answers into debug msgs
462b3a491347 build: use pthread cflags/ldflags
Signed-off-by: Felix Fietkau <nbd@nbd.name>
d590fbd255ce wireless: always enable bpdu filter for AP interfaces and VLANs
f8ff6d820283 system-linux: remove copy&paste from /proc and /sys path names
300b1220fab3 wireless: improve reliability of proxyarp support
5ba9744aac6d device: add support for configuring bonding devices
6fa9b042ff4d wireless: only apply wireless device attributes to the base vif interface
06d11bbf1f2b wireless: only enable proxyarp/isolate for AP vifs
08e954e137ff bonding: claim the port device before creating the bonding device
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds the hash also for the aarch64 toolchain in addition to the
x86_64 toolchain. This gets the build on a Linux aarch64 host one step
further.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates libtool to its current release, from 2015. Current patches
were renumbered and given a description text. The fix in
160-passthrough-ssp.patch is no longer needed.
A patch to speed up build was cherry-picked, and another openwrt
specific patch was needed to not use quotes in $(SHELL), to acommodate
our "SHELL=/usr/bin/env bash" usage.
The already present call to ./bootstrap ensures that generated files are
refreshed, so the patches are applied only to their sources. Also, that
bootstrap call was adjusted to run at the appropriate time when QUILT=1.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
