With upstream accepted "mac-base" binding there is no need for a
downstream "mac-address-ascii" workaround anymore.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit daaa0c1b25)
Link: https://github.com/openwrt/openwrt/pull/15917
Huawei AP5030DN is a dual-band, dual-radio 802.11ac Wave 1 3x3 MIMO
enterprise access point with two Gigabit Ethernet ports and PoE
support.
Hardware highlights:
- CPU: QCA9550 SoC at 720MHz
- RAM: 256MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: QCA9550-internal radio
- Wi-Fi 5GHz: QCA9880 PCIe WLAN SoC
- Ethernet 1: 10/100/1000 Mbps Ethernet through Broadcom B50612E PHY
- Ethernet 2: 10/100/1000 Mbps Ethernet through Marvell 88E1510 PHY
- PoE: input through Ethernet 1 port
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: SGM706 (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- eth1 = label MAC + 1
- radio0 (Wi-Fi 5GHz) = label MAC + 2
- radio1 (Wi-Fi 2.4GHz) = label MAC + 3
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script
"run ramboot". Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile
openwrt-ath79-generic-huawei_ap5030dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot
be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap5030dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from
non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP5X30XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap5030dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues
-----------------------
- On initial power-up, the Huawei-modified bootloader suspends both
ethernet PHYs (it sets the "Power Down" bit in the MII control
register). Unfortunately, at the time of the initial port, the kernel
driver for the B50612E/BCM54612E PHY behind eth0 doesn't have a resume
callback defined which would clear this bit. This makes the PHY unusable
since it remains suspended forever. This is why the backported kernel
patches in this commit are required which add this callback and for
completeness also a suspend callback.
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the CPU_CLK/4 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
[fixed 6.6 backport patch naming]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 06cdc07f8c)
Ubiquiti Rocket M XW is a single-band, 2x2:2 external Wi-Fi AP, with optional
GPS receiver, with two external RP-SMA antenna connections, based on
AR9342 SoC. Two band variants exists, for 2.4GHz and 5GHz band, usable
with the same image.
Specs:
- CPU: Atheros AR9342 MIPS SoC at 535MHz
- RAM: 64MB DDR400
- ROM: 8MB SPI-NOR in SO16W package, MX25L6408E
- Wi-Fi Atheros AR9342 built-in 2x2:2 radio
- Ethernet: Atheros AR8035 PHY, limited to 100Mbps speeds due to
magnetics
- Power: 24V passive PoE input.
Installation: please refer to Ubiquiti Bullet M2HP for documentation.
The device runs with exactly same image as the Bullet, and after fixes
in preceding commit, is fully functional again. Add the alternative name
to the build system.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 54387fddea)
Since commit 6f2e1b7485 ("ath79: disable delays on AT803X config init")
Ubiquiti XW boards equipped with AR8035 PHY suffered from lack of
outbound traffic on the Ethernet port. This was caused by the fact, the
U-boot has set this during boot and it wasn't reset by the PHY driver,
and the corresponding setting in device tree was wrong.
Set the 'phy-mode = "rgmii-txid"' at the ð0, and drop this property
from PHY node, as it is not parsed there. This causes the device to
connect using Ethernet once again.
Fixes: db4b6535f8 ("ath79: Add support for Ubiquity Bullet M (XW)")
Fixes: 6f2e1b7485 ("ath79: disable delays on AT803X config init")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit a9b2ba4d7b)
Onboard AR8035 PHY supports 1000Base-T operation, but onboard
Ethernet magnetics do not. Reduce advertised link speeds to 100Mbps and
lower.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit d406777fb1)
Kernel 5.15 introduced a significant change to spi-nor subsystem [1],
which would the SPI-NOR core to no longer unprotect the Flash chips if
their protection bits are non-volatile, which is the case for MX25L6405D
and MX25L12805D, used in Ubiquiti XW and WA lines of devices [2].
However, their bootloader forcibly enables this protection before
continuing to boot, making the kernel not unprotect the flash upon boot,
causing JFFS2 to be unable write to the filesystem. Because sysupgrade
seems to unlock the flash explicitly, the upgrade will work, but the
system will be unable to save configrationm showing the following symptom
in the kernel log:
[ 86.168016] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 86.192344] jffs2_build_filesystem(): unlocking the mtd device...
[ 86.192443] done.
[ 86.200669] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 86.220646] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001e0000
[ 86.292388] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001d0000
[ 86.324867] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001c0000
[ 86.355316] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001b0000
[ 86.402855] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001a0000
Disable the write protection unconditionally for ath79/generic subtarget,
so the XW and WA devices can function again. However, this is only a
stopgap solution - it probably should be investigated if there is a way
to selectively unlock the area used by rootfs_data - but given the lock
granularity, this seems unlikely.
With this patch in place, rootfs_data partition on my Nanostation Loco
M5 XW is writable again.
Fixes: #12882Fixes: #13750
Fixes: 579703f38c ("ath79: switch to 5.15 as default kernel")
Link: http://www.infradead.org/pipermail/linux-mtd/2020-October/082805.html
Link: https://forum.openwrt.org/t/powerbeam-m5-xw-configuration-loss-after-reboot/141925
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit f024f4b1b0)
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Read back the reset register in order to flush the cache. This fixes
spurious reboot hangs on TP-Link TL-WDR3600 and TL-WDR4300 with Zentel
DRAM chips.
This issue was fixed in the past, but switching to the reset-driver
specific implementation removed the cache barrier which was previously
implicitly added by reading back the register in question.
Link: https://github.com/freifunk-gluon/gluon/issues/2904
Link: https://github.com/openwrt/openwrt/issues/13043
Link: https://dev.archive.openwrt.org/ticket/17839
Link: f8a7bfe1cb2c ("MIPS: ath79: fix system restart")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2fe8ecd880)
Hardware
--------
CPU: Qualcomm Atheros QCA9563
RAM: 128M DDR2
FLASH: 16MB SPI-NOR
WiFi: Qualcomm Atheros QCA9563 2x2:2 802.11n 2.4GHz
Qualcomm Atheros QCA9880 2x2:2 802.11ac 5GHz
Antennas
--------
The device features internal antennas as well as external antenna
connectors. By default, the internal antennas are used.
Two GPIOs are exported by name, which can be used to control the
antenna-path mux. Writing a logical 0 enables the external antenna
connectors.
Installation
------------
1. Download the OpenWrt sysupgrade image to the device. You can use scp
for this task. The default username and password are "ubnt" and the
device is reachable at 192.168.1.20.
$ scp -O openwrt-sysupgrade.bin ubnt@192.168.1.20:/tmp/firmware.bin
2. Connect to the device using SSH.
$ ssh ubnt@192.168.1.20
3. Disable the write-protect
$ echo "5edfacbf" > /proc/ubnthal/.uf
4. Verify kernel0 and kernel1 match mtd2 and mtd3
$ cat /proc/mtd
5. Write the sysupgrade image to kernel0 and kernel1
$ dd if=/tmp/firmware.bin of=/dev/mtdblock2
$ dd if=/tmp/firmware.bin of=/dev/mtdblock3
6. Write the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtd4
7. Reboot the device
$ reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit bf94e0a383)
This allows us to embrace alphabetical sorting for the UK-Ultra.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit c9e58f85f6)
This service was unfunctional due to not having its executable bit
set.
Fixes#13500.
Signed-off-by: Eric J. Anderson <eric.j.ason256@gmail.com>
(cherry picked from commit 807acbce66)
Due to circuit issue or silicon defect, sometimes the WiFi switch button
of the Archer C7 v2 can be accidentally triggered multiple times in one
second. This will cause WiFi to be unexpectedly shut down and trigger
'irq 23: nobody cared'[1] warning. Increasing the key debounce interval
to 1000 ms can fix this issue. This patch also add the missing rfkill
key label.
[1] Warning Log:
```
[87765.218511] irq 23: nobody cared (try booting with the "irqpoll" option)
[87765.225331] CPU: 0 PID: 317 Comm: irq/23-keys Not tainted 5.15.118 #0
...
[87765.486246] handlers:
[87765.488543] [<85257547>] 0x800c29a0 threaded [<5c6328a2>] 0x80ffe0b8 [gpio_button_hotplug@4cf73d00+0x1a00]
[87765.498364] Disabling IRQ #23
```
Fixes: https://github.com/openwrt/openwrt/issues/13010
Fixes: https://github.com/openwrt/openwrt/issues/12167
Fixes: https://github.com/openwrt/openwrt/issues/11191
Fixes: https://github.com/openwrt/openwrt/issues/7835
Tested-by: Hans Hasert
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit e32f70e706)
The compex WPJ563 actually has both usb controllers wired:
usb0 --> pci-e slot
usb1 --> pin header
As the board exposes it for generic use, enable this controller too.
fixes: #13650
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
(cherry picked from commit 9188c77cbe)
On some WLR-7100 routers, significant packet loss was observed. This is
fixed by configuring a delay on the GMAC0 RXD and RXDV lines.
The values used in this commit are copied from the values used by the
stock firmare (based on register dumping).
Out of four test routers, the problem was consistently observed on two.
It is unclear what the relevant difference is exactly (the two working
routers were v1 001 with AR1022 and v1 002 with AR9342, the two broken
routers were both v1 002 with AR1022). All PCB routing also seems
identical, so maybe there is some stray capacitance on some of these
that adds just enough delay or so...
With this change, the packet loss disappears on the broken routers,
without introducing new packet loss on the previously working routers.
Note that the PHY *also* has delays enabled (through
`qca,ar8327-initvals`) on both RX and TX lines, but apparently that is
not enough, or it is not effective (registers have been verified to be
written).
For detailed discussion of this issue and debug history, see
https://forum.openwrt.org/t/sitecom-wlr-7100-development-progress/79641
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
(cherry picked from commit d2ce3a61aa)
From the Netgear u-boot GPL code[1]. Bootloader always unconditionally
marks block 768, 1020 - 1023 as bad blocks on each boot. This may lead
to conflicts with the OpenWrt nand driver since these blocks may be good
blocks. In this case, U-boot will override the oob of these blocks so
that break the ubi volume. The system will be damaged after first reboot.
To avoid this issue, manually skip these blocks by using "mtd-concat".
[1] https://www.downloads.netgear.com/files/GPL/EX7300v2series-V1.0.0.146_gpl_src.tar.bz2.zip
Fixes: https://github.com/openwrt/openwrt/issues/8878
Tested-by: Yousaf <yousaf465@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 12f53724c6)
In Netgear u-boot GPL code, nand devices uses this formula to locate the
rootfs offset.
offset = (((128 + KERNEL_SIZE) / BLOCK_SIZE) + 1) * BLOCK_SIZE;
Howerver, WNDR4500 source code incorrectly define the nand block size to
64k. In some cases, it causes u-boot can't get the correct rootfs offset,
which result in boot failure. This patch workaround it by padding kernel
size to (128k * n - 128 - 1). The additional char '\0' is used to ensure
the (128 + KERNEL_SIZE) can't be divided by the BLOCK_SIZE.
Fixes: https://github.com/openwrt/openwrt/issues/13050
Fixes: 3c1512a25d ("ath79: optimize the firmware recipe for Netgear NAND devices")
Tested-by: Yousaf <yousaf465@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 0f9b8aa3f5)
return ubnt_rocket-m and ubnt_powerbridge-m back to ath79-generic
They have enough RAM-ressources to not be considered as tiny.
This reverts the commit f4415f7635 partially
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
(cherry picked from commit 9e86a96af5)
1. Add new symbols to generic config
2. Bump kernel
Changelog: https://lore.kernel.org/stable/2023080818-groin-gradient-a031@gregkh/
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
[Refreshed on top of OpenWrt 23.05]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit daed3322d3)
Mikrotik RB951 router has a buzzer on the board, which makes annoying noises
due to the interference caused by PoE input or Wifi transmission
when no GPIO pin state is set.
I added buzzer node to device's DTS in order to set deault level to 1
and to provide easier access for it.
Signed-off-by: Pavel Pernička <pernicka.pa@gmail.com>
(cherry picked from commit dac0a133cf)
MikroTik RB951G-2HnD is a wireless SOHO router that was previously
supported by the ar71xx target, see commit 7a709573d7 ("ar71xx: add
kernel support for the Mikrotik RB951G board").
Specifications
--------------
- SoC: Atheros AR9344 (600 MHz)
- RAM: 128 MB (2x 64 MB)
- Storage: 128 MB NAND flash (various manufacturers)
- Ethernet: Atheros AR8327 switch, 5x 10/100/1000 Mbit/s
- 1x PoE in (port 1, 8-30 V input)
- Wireless: Atheros AR9340 (802.11b/g/n)
- USB: 2.0 (1A)
- 8x LED:
- 1x power (green, not configurable)
- 1x user (green, not configurable)
- 5x GE ports (green, not configurable)
- 1x wireless (green, not configurable)
- 1x button (restart)
Unlike on the RB951Ui-2HnD, none of the LEDs on this device seem to be
GPIO-controllable, which was also the case for older OpenWRT versions
that supported this board via a mach file. The Ethernet port LEDs are
controlled by the switch chip.
See https://mikrotik.com/product/RB951G-2HnD for more details.
Flashing
--------
TFTP boot initramfs image and then perform sysupgrade. Follow
common MikroTik procedures at https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
(cherry picked from commit db02cecd6a)
Mikrotik RouterBOARD 951Ui-2HnD and Mikrotik RouterBOARD RB951G-2HnD are
very similar devices. Extract the DTS bits that are identical for these
two boards to a separate DTSI file.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
(cherry picked from commit c6ef417094)
Hardware
========
CPU Qualcomm Atheros QCA9558
RAM 256MB DDR2
FLASH 2x 16M SPI-NOR (Macronix MX25L12805D)
WIFI Qualcomm Atheros QCA9558
Atheros AR9590
Installation
============
1. Attach to the serial console of the AP-105.
Interrupt autoboot and change the U-Boot env.
$ setenv rb_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66;
netget 0x80060000 ap115.bin; go 0x80060000"
$ setenv fb_openwrt "bank 1;
cp.b 0xbf100040 0x80060000 0x10000; go 0x80060000"
$ setenv bootcmd "run fb_openwrt"
$ saveenv
2. Load the OpenWrt initramfs image on the device using TFTP.
Place the initramfs image as "ap105.bin" in the TFTP server
root directory, connect it to the AP and make the server reachable
at 192.168.1.66/24.
$ run rb_openwrt
3. Once OpenWrt booted, transfer the sysupgrade image to the device
using scp and use sysupgrade to install the firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1b467a902e)
Specifications:
SOC: QCA9563 775 MHz + QCA9880
Switch: QCA8337N-AL3C
RAM: Winbond W9751G6KB-25 64 MiB
Flash: Winbond W25Q128FVSG 16 MiB
WLAN: Wi-Fi4 2.4 GHz 3*3 + 5 GHz 3*3
LAN: LAN ports *4
WAN: WAN port *1
Buttons: reset *1 + wps *1
LEDs: ethernet *5, power, wlan, wps
MAC Address:
use address source1 source2
label 40:9b:xx:xx:xx:3c lan && wlan u-boot,env@ethaddr
lan 40:9b:xx:xx:xx:3c devdata@0x3f $label
wan 40:9b:xx:xx:xx:3f devdata@0x8f $label + 3
wlan2g 40:9b:xx:xx:xx:3c devdata@0x5b $label
wlan5g 40:9b:xx:xx:xx:3e devdata@0x76 $label + 2
Install via Web UI:
Apply factory image in the stock firmware's Web UI.
Install via Emergency Room Mode:
DIR-859 A1 will enter recovery mode when the system fails to boot
or press reset button for about 10 seconds.
First, set computer IP to 192.168.0.5 and Gateway to 192.168.0.1.
Then we can open http://192.168.0.1 in the web browser to upload
OpenWrt factory image or stock firmware. Some modern browsers may
need to turn on compatibility mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 0ffbef9317)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
1. Remove unnecessary new lines in the dts.
2. Remove duplicate included file "gpio.h" in the device dts.
3. Add missing button labels "reset" and "wps".
4. Unify the format of the reg properties.
5. Add u-boot environment support.
6. Reduce spi clock frequency since the max value suggested by the
chip datasheet is only 25 MHz.
7. Add seama header fixup for DIR-859 A1. Without this header fixup,
u-boot checksum for kernel will fail after the first boot.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit e5d8739aa8)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch enables NVMEM u-boot-env driver (COFNIG_NVMEM_U_BOOT_ENV) on
generic subtarget to use from devices, for MAC address and etc.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(cherry picked from commit e8f7957450)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This removes unneeded kernel version switches from the targets after
kernel 5.10 has been dropped.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Recently, a strange variant of ZTE MF286 was discovered, having QCA9886
radio instead of QCA9882 - like MF286A, but having MF286 flash layout
and rest of hardware.
To support both variants in one image, bind calibration data at offset
0x5000 both as "calibration" and "pre-calibration" nvmem-cells, so
ath10k can load caldata for both at runtime.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Specifications
The D-Link EXO AC1750 (DIR-869) router released in 2016.
It is powered by Qualcomm Atheros QCA9563 @ 750 MHz chipset, 64 MB RAM and 16 MB flash.
10/100/1000 Gigabit Ethernet WAN port
Four 10/100/1000 Gigabit Ethernet LAN ports
Power Button, Reset Button, WPS Button, Mode Switch
Flashing
1. Upload factory.bin via D-link web interface (Management/Upgrade).
Revert to stock
Upload original firmware via OpenWrt sysupgrade interface.
Debricking
D-Link Recovery GUI (192.168.0.1)
Signed-off-by: Jan Forman <forman.jan96@gmail.com>
For D-link DIR-859 and DIR-869
Replace the mtd-cal-data by an nvmem-cell.
Add the PCIe node for the ath10k radio to the devicetree.
Thanks to DragonBlue for this patch
Signed-off-by: Jan Forman <jforman@tuta.io>
gpio-export for the switch reset pin replaced with a reset pin definition for the driver, within the phy node.
Signed-off-by: Jan Forman <forman.jan96@gmail.com>
Tested-By: Sebastian Schaper <openwrt@sebastianschaper.net>
support for MR18 and MR26 was developped before
the userspace nu801 was integrated with x86's
MX100 into OpenWrt. The initial nu801 + kmod-leds-uleds
caused build-bot errors.
The solution that worked for the MX100 was to include
the kmod-leds-uleds to the device platform module.
Thankfully, the MR26 and MR18 can just add the uleds
package to the DEVICE_PACKAGES variable.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
