TP-Link RE205 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with external antennas.
It's based on MediaTek MT7628AN+MT7610EN like the RE200 v3/v4 but with
external antennas.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 5x LED (GPIO-controlled), 2x button
- UART connection holes on PCB (57600 8n1)
There are 2.4G and 5G LEDs in blue which are controlled separately.
Installation
------------
Installation is identical to RE200 v3 devices as described at
https://openwrt.org/toh/tp-link/re200#installation
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Recovery
--------
U-Boot seems to be locked on newer versions, if not it can be accessed over
the UART as described in the link above.
Signed-off-by: Steffen Loley <slo-src@web.de>
This service was unfunctional due to not having its executable bit set.
Furthermore, sysupgrade complains about the file being present in images.
Also, the tc654 driver doesn't provide pwm1_enable sysfs file, instead its
now called pwm1_mode.
Please note that the fan was always spinning. It should now turn off, when
there's enough the thermal headroom.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
D-Link DGS-1210-16 hangs when rebooting and has no support for the reset
button.
Fix both by enabling the same GPIOs for reboot and the reset button as
already used for D-Link DGS-1210-20 and D-Link DGS-1210-28.
Signed-off-by: Richard Kunze <kunze@tivano.de>
When rebasing patches on top of 6.1, a change that removed NF_TABLES
from NF_FLOW_TABLE's dependency was dropped accidentally, and iptables
flow offload module can only be built when nftables is selected.
Restore the change to fix it.
Fixes: 19a246bb65 ("generic: 6.1: manually refresh hack patches")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Radxa E25 is a network application carrier board for the Radxa CM3
Industrial (CM3I) SoM, which is based on the Rockchip RK3568 SoC.
It has the following features:
- MicroSD card socket, on board eMMC flash
- 2x 2.5GbE Realtek RTL8125B Ethernet transceiver
- 1x USB Type-C port (Power and Serial console)
- 1x USB 3.0 OTG port
- mini PCIe socket (USB or PCIe)
- ngff PCIe socket (USB or SATA)
- 1x User LED and 16x RGB LEDs
- 26-pin expansion header
Installation:
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Kernel 6.6 has changed the path of WLAN devices as the soc node was updated
to include an adress as well because according to spec it needed one:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v6.6.21&id=da6aa1111a17db11367817ddc10c5a6c188cdc44
So, this will break existing configuration as device path was changed for
example:
"platform/soc/c000000.wifi" to "platform/soc@0/c000000.wifi"
"platform/soc/c000000.wifi+1" to "platform/soc@0/c000000.wifi+1"
PCIe attached devices also have their path changed, so lets add a script
that will migrate the paths based on the detected running kernel version
so returning to kernel 6.1 will work as well.
Co-developed-by: Sean Khan <datapronix@protonmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Robert Marko <robimarko@gmail.com>
When building MT7629 with ALL_KMODS then we get prompted for
LEDS_SMARTRG_LED and this will break CI and in future buildbot compilation.
It depends on I2C so the symbol is hidden until ALL_KMODS is used and I2C
support is available, so disable the LEDS_SMARTRG_LED symbol in 6.6 config
intentionally as is done in the 6.1 mt7629 config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Disable CONFIG_CRYPTO_SM4_ARM64_CE_CCM and CONFIG_CRYPTO_SM4_ARM64_CE_GCM
in the generic config like we do with similar CE symbols.
This avoids the need to disable them in individual targets.
Signed-off-by: Robert Marko <robimarko@gmail.com>
* have more defined PWM steps similar to the vendor's shell script doing
the same thing
* replace PWM values with experiencal values provided by forum users
* increase hyteresis to prevent changing fan speed every second
(just because it's annoying to listen to)
* add 'hot' trip point at 75 deg. to warn users that shutdown is imminent
Tested on Puzzle M902 only for now, PWM values for Puzzle M901 might be
slightly different but should quite certainly also be rised.
Suggested-by: Martin Gierschner <martin_gierschner@gmx.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The vendor u-boot knows nothing about UBI, and we used to have a
fixed-size kernel partition for vendor u-boot and UBI for rootfs.
However, that fixed partition becomes too small eventually, and
expanding it requires complicated procedure.
This commit changed the flash layout and added a second u-boot
where the kernel supposed to be.
Now the vendor u-boot chainloads our mainline u-boot, and our
u-boot reads kernel+rootfs from UBI, verifies it, and boot
into OpenWrt.
There are two possible ways to convert from the old fw:
Flash the factory image using mtd (provided by @rany2):
mount -o remount,ro /
mount -o remount,ro /overlay
cd /tmp
dd if=factory.bin bs=1M count=4 | mtd write - kernel
dd if=factory.bin bs=1M skip=4 | mtd -r write - ubi
Or, flash the 2nd u-boot via mtd and upload the firmware
to the 2nd u-boot using tftp:
1. prepare a tftp server at 192.168.1.254 to serve the
sysupgrade image:
openwrt-mediatek-mt7622-xiaomi_redmi-router-ax6s-squashfs-sysupgrade.itb
2. upload the ubi-loader.itb to OpenWrt /tmp, and flash it to
the old kernel partition:
mtd -r write openwrt-mediatek-mt7622-xiaomi_redmi-router-ax6s-ubi-loader.itb
3. The router should reboot and flash the sysupgrade image via TFTP.
Procedure for flashing from vendor firmware shouldn't change.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
With kernel 6.1 image size is too large for Edgerouter X current size
limit and is causing the buildbots to fail building so images for other
devices are not updated as well.
So, disable building Edgerouter X images until a workaround is found.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream commit e298d8a38b23 [0] changed method how to blink delays are pased
to function. Downstream commit must follow it.
[0] https://lore.kernel.org/r/20230510162234.291439-2-hdegoede@redhat.com
Reported-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Currently, 6 MAC addresses are read from the "boarddata1" partition and set for network interfaces in sequence.
This partition only contains 3 MAC addresses:
1. lan mac
2. wan mac
3. wlan5g mac
As result only lan2, lan3 and lan4 have correct (OUI) MAC addresses.
lan1, lan5 and wan interfaces get MAC addresses with incorrect OUI from random data on "boarddata1" partition.
This commit fix this and use first MAC for lan and second MAC for wan interfaces.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
The port 5 of most ipq60xx devices is connected to qca8075,
a few are connected to qca8081. So assume that the default
connection is qca8075 and set the phy mode to psgmii.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Marvell's thermal sensors do not support interrupts, so we need to
poll them. Reading temperature every second should be enough to
control the fan.
While at it, also make sure fan speed is reduced again if temperature
goes down.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
On Buffalo WXR-5590AX12, some LEDs don't have "function" property and
only "color" property is available for the newer binding of LED on
Linux Kernel.
2e659930d3 ("qualcommax: drop redundant label with new LED
color/function format") removes "label" property from LEDs, then,
multiple "<color>:" (ex.: "white:"/"red:") will be appeared as LED names
and renamed to "<color>:_<num>" ("ex.: "white:_1", "green:_2", ...) by
kernel.
logs:
[ 5.372863] leds-gpio leds: Led white: renamed to white:_1 due to name collision
[ 5.375796] leds-gpio leds: Led red: renamed to red:_1 due to name collision
/sys/class/leds:
root@OpenWrt:/# ls /sys/class/leds/
red: red:power white: white:power
red:_1 red:wlan white:_1 white:wlan
Fix this issue by adding missing "function" property to LEDs on Buffalo
WXR-5950AX12.
Note: there are no appropriate functions in dt-bindings/leds/common.h
for some LEDs, so use the hardcoded strings for them instead.
Fixes: 2e659930d3 ("qualcommax: drop redundant label with new LED color/function format")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
On QNAP QHora-301W, all LEDs don't have "function" property and only
"color" property is available for the newer binding of LED on Linux
Kernel.
2e659930d3 ("qualcommax: drop redundant label with new LED
color/function format") removes "label" property from LEDs, then,
multiple "<color>:" (ex.: "amber:"/"green:"/"red:") will be appeared as
LED names and renamed to "<color>:_<num>" ("ex.: "green:_1", "green:_2",
...) by kernel.
logs:
[ 4.246494] leds-gpio leds: Led green: renamed to green:_1 due to name collision
[ 4.248978] leds-gpio leds: Led green: renamed to green:_2 due to name collision
[ 4.256345] leds-gpio leds: Led green: renamed to green:_3 due to name collision
[ 4.263770] leds-gpio leds: Led green: renamed to green:_4 due to name collision
[ 4.271105] leds-gpio leds: Led amber: renamed to amber:_1 due to name collision
[ 4.278487] leds-gpio leds: Led green: renamed to green:_5 due to name collision
[ 4.285856] leds-gpio leds: Led amber: renamed to amber:_2 due to name collision
[ 4.293257] leds-gpio leds: Led green: renamed to green:_6 due to name collision
[ 4.300616] leds-gpio leds: Led amber: renamed to amber:_3 due to name collision
[ 4.308002] leds-gpio leds: Led green: renamed to green:_7 due to name collision
[ 4.315384] leds-gpio leds: Led amber: renamed to amber:_4 due to name collision
[ 4.322760] leds-gpio leds: Led green: renamed to green:_8 due to name collision
[ 4.330135] leds-gpio leds: Led amber: renamed to amber:_5 due to name collision
/sys/class/leds:
amber: amber:_4 green:_2 green:_6
amber:_1 green:_5 green:_3 green:_7
amber:_2 green: green:_4 green:_8
amber:_3 green:_1 green:_5 red:
Fix this issue by adding missing "function" (and "function-enumerator")
property to LEDs on QNAP QHora-301W.
Note: there are no appropriate functions in dt-bindings/leds/common.h
for some LEDs, so use the hardcoded strings for them instead.
Fixes: 2e659930d3 ("qualcommax: drop redundant label with new LED color/function format")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is needed recommended.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Dual-slot NAS based on Marvell Kirkwood.
Specifications:
- Marvell 88F6281 @1GHz
- 128Mb RAM
- 256Mb NAND
- 1x GbE LAN (Marvell 88E1116)
- 1x USB 2.0
- 2x SATA
- PCF8563 RTC
- LM75 sensor
- TC654 PWM fan controller
- Serial on J2 (115200,8n1)
- Newer bootROM so kwboot-ing via serial is possible
Installation:
1. Serial console
- Connect your levelshifter to the serial console
on J2 (refer to the wiki page for pinout)
2. Update u-boot
- Download the u-boot.kwb image for the device
- Powercycle the NAS
- Run "kwboot -b ./u-boot.kwb /dev/ttyUSB0 -p"
- Connect to the serial console with minicom
- tftp 0x0800000 netgear_stora-u-boot.kwb
- nand erase 0x0 100000
- nand write 0x0800000 0x0 0x100000
- reset
3. Install OpenWrt
- Boot up the initramfs image
- tftpboot 0x800000 openwrt-kirkwood-netgear_stora-initramfs-uImage; bootm 0x800000
- Download the sysupgrade image and perform sysupgrade
The fan is controlled in 3 stages by a script running every minute
from cron, measuring the CPU temperature.
Snippets taken from bodhi <mibodhi@gmail.com>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The dir variable has been used uninitialized since the port to 5.10, and
somehow this remains undetected by GCC.
Fixes: b10d604459 ("kernel: add linux 5.10 support")
Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn>
Most mt7622 devices use the mt7531 switch, which have been
switched to dsa driver for a long time. So use dsa as the
default configuration and configure these rtl8367s devices
separately. This reduces the amount of code.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
In kernel 6.6, dts files for mediatek arm target are moved into
arch/arm/boot/dts/mediatek instead of legacy path arch/arm/boot/dts.
To avoid dts compile failure, change DTS_DIR to the mediatek subfolder
for kernel 6.6.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Also backport most recent MHI modem additions to Linux 6.6.
Adds support for generic SDX75-based modems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add missing CLK_TOP_PEXTP_Px_SEL clock for each of the 4 PCIe interfaces
of the MT7988 SoC. Without that clock PCIe doesn't work reliable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CONFIG_NET_VENDOR_DAVICOM is needed to activate the CONFIG_DM9000 option
which builds the kmod-dm9000. This fixes the following warning:
logs/package/kernel/linux/compile.txt:WARNING: kmod-dm9000 is not available in the kernel config - generating empty package
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
