MR600 V2(EU) is an LTE router that also supports 4G+ band aggregation
etc. and can reportedly achieve higher bandwidth with it.
- Specifications:
* SoC: Mediatek MT7621DAT 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (GD25Q128C)
* LTE Modem: Qualcomm MDM9240
* WiFi 5GHz: Mediatek MT7613BEN
* WiFi 2.4GHz: Mediatek MT7603EN
* Ethernet: MT7530, 4x 1000Base-T.
* UART: Serial console (115200 8n1), J1(GND:3)
* Buttons: Reset, WPS.
* LED: Power, WAN, LTE, WiFi 2GHz and 5GHz, LAN, Signal1, Signal2,
Signal3
- MAC Addresses:
OEM firmware configuration:
54:af:97:xx:xx:7b : 2.4G
54:af:97:xx:xx:7a : 5G
54:af:97:xx:xx:7c : LTE
54:af:97:xx:xx:7b : LAN (label)
54:af:97:xx:xx:7c : WAN
- Installation:
1. Download the OpenWrt initramfs-image.
Place it into a TFTP server root directory and rename it to openwrt.img
Configure the TFTP server to listen at 192.168.0.5/24.
3. Connect to the serial console.
Attach power and interrupt the boot procedure when prompted (type `tpl`).
Credentials are admin / 1234
4. Configure U-Boot for booting OpenWrt from ram
$ tftpboot
$ bootm
5. Transfer the OpenWrt sysupgrade image to the device.
- LTE:
In order to setup the wwan0 interface:
1. Add a `qmi` proto interface under `/etc/config/network`, e.g.:
```
config interface 'wwan0'
option device '/dev/cdc-wdm0'
option proto 'qmi'
option pincode 'XXXX'
option apn 'your_isp_apn'
```
2. Add `wwan0` interface to the `wan` firewall zone
3. `/etc/init.d/network restart`
Signed-off-by: Linos Giannopoulos <linosgian00@gmail.com>
SIM AX18T and Haier HAR-20S2U1 Wi-Fi6 AX1800 routers are designed based
on Tenbay WR1800K. They have the same hardware circuits and u-boot.
SIM AX18T has three carrier customized models: SIMAX1800M (China Mobile),
SIMAX1800T (China Telecom) and SIMAX1800U (China Unicom). All of these
models run the same firmware.
Specifications:
SOC: MT7621 + MT7905 + MT7975
ROM: 128 MiB
RAM: 256 MiB
LED: status *3 R/G/B
Button: reset *1 + wps/mesh *1
Ethernet: lan *3 + wan *1 (10/100/1000Mbps)
TTL Baudrate: 115200
TFTP Server: 192.168.1.254
TFTP IP: 192.168.1.28 or 192.168.1.160 (when envs is broken)
MAC Address:
use address source
label 30:xx:xx:xx:xx:62 wan
lan 30:xx:xx:xx:xx:65 factory.0x8004
wan 30:xx:xx:xx:xx:62 factory.0x8004 -3
wlan2g 30:xx:xx:xx:xx:64 factory.0x0004
wlan5g 32:xx:xx:xx:xx:64 factory.0x0004 set 7th bit
TFTP Installation (initramfs image only & recommend):
1. Set local tftp server IP: 192.168.1.254 and NetMask: 255.255.255.0
2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root
directory of the tftp server. (tftpd64 is a good choice for Windows)
3. Start the TFTP server, plug in the power supply, and wait for the
system to boot.
4. Backup "firmware" partition and rename it to "firmware.bin", we need
it to back to stock firmware.
5. Use "fw_printenv" command to list envs.
If "firmware_select=2" is observed then set u-boot enviroment:
/# fw_setenv firmware_select 1
6. Apply sysupgrade.bin in OpenWrt LuCI.
Web UI Installation:
1. Apply update by uploading initramfs-factory.bin to the web UI.
2. Use "fw_printenv" command to list envs.
If "firmware_select=2" is observed then set u-boot enviroment:
/# fw_setenv firmware_select 1
3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI.
Recovery to stock firmware:
a. Upload "firmware.bin" to OpenWrt /tmp, then execute:
/# mtd -r write /tmp/firmware.bin firmware
b. We can also write factory image "UploadBrush-bin.img" to firmware
partition to recovery. Upload image file to /tmp, then execute:
/# mtd erase firmware
/# mtd -r write /tmp/UploadBrush-bin.img firmware
How to extract stock firmware image:
Download stock firmware, then use openssl:
openssl aes-256-cbc -d -salt -in [Downloaded_Firmware] \
-out "firmware.tar.tgz" -k QiLunSmartWL
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Description heavily based on commit
7e89421a7c by
Sergey Ryazanov <ryazanov.s.a@gmail.com> Details I cannot confirm have
been removed
Completed with great help from \x on IRC. Thanks, \x!
Zbtlink ZBT-WG1602-V04 is a Wi-Fi router intendend for use with WWAN
(UMTS/LTE/3G/4G) modems. The router board offers a couple of miniPCIe
slots with USB and SIM only and another one which is a pure miniPCIe
slot as well as five Gigabit Ethernet ports (4xLAN + WAN).
Specification:
* SoC: MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB
* Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* WLAN 2GHz: MT7603E (.11bgn, MIMO 2x2)
* WLAN 5GHz: MT7662E (.11nac, MIMO 2x2)
* WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios
* miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus
* WWAN Ants: detachable x4
* External storage: microSD (SDXC) slot
* USB: 3.0 Type-A port
* LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled,
1 power indicator)
* Button: 1 (reset)
* UART: console (115200 baud)
* Power: DC jack (12 V / 2.5 A)
Additional HW information:
* SoC USB port 1 is shared by internal miniPCIe slot and external
Type-A USB port, USB D+/D- lines are toggled between ports using a
GPIO controlled DPDT switch.
Installation:
The kernel image can be installed directly onto the device via a browser
to 192.168.1.1 using the built in firmware recovery Web UI available.
It can be accessed by pushing the reset button in, applying power and
holding the reset button for approximately 10 seconds. When the kernel
image has been flashed, you can access LuCI and upload the sysupgrade
as normal.
Signed-off-by: Alexander Horner <ahorner@programmer.net>
Add UIMAGE_NAME and UIMAGE_MAGIC to allow users to directly install
initramfs-kernel.bin from the stock firmware Web UI. At the same time,
this change makes it possible to boot OpenWrt with the official u-boot.
Notice:
Since the stock firmware is based on OpenWrt and the configuration
will be retained by default during the upgrade process, so we must use
initramfs-kernel.bin to do a initial installation. After the system
restarts, install sysupgrade.bin and do not retain any configuration.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
In my commit da5c45f4d8 ("kernel: remove handling of xfrm[4|6]_mode_*
modules") I missed a few default config options and description entries.
Those should be gone as well.
Fixes: da5c45f4d8 ("kernel: remove handling of xfrm[4|6]_mode_* modules")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
The patch "210-pinctrl-mediatek-add-support-for-MT7986-SoC.patch" and
"212-clk-mediatek-add-mt7986-clock-support.patch" are upstreamed.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The patches "191-arm64-dts-mt7622-specify-the-L2-cache-topology.patch"
and "192-arm64-dts-mt7622-specify-the-number-of-DMA-requests.patch" are
upstreamed to 5.19.
Signed-off-by: Nick Hainke <vincent@systemli.org>
This subtarget supports 3 devices:
* Bananapi BPi-R3 (added in a96382c1bb),
* MediaTek MTK7986 rfba AP (added in cffc77ae55),
* MediaTek MTK7986 rfbb AP (added in cffc77ae55).
This subtarget supports DSA from the beginning. It looks like CONFIG_SWCONFIG
was copied from another config when the subtarget was created.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Backport patches from net-next which fix possible memory and resource
leaks in the error codepaths of WED initialization.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The packet processing engine (PPE) found in newer ARM-based MediaTek
SoCs provides packet and byte counters for offloaded streams.
Import pending patch reading and using those counters.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patch enabling hardware flow offloading support on the MT7623 SoC
has been merged upstream as of Linux 5.13. Remove our local patch which
wrongly got forward-ported and now actually enables hardware flow
offloading for the MT2701 SoC family (unsupported in OpenWrt).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
After replacing the R4K event timer and clock source with the new
Realtek Otto timer, performance for RTL839x devices was severely
impacted, as reported by Hiroshi.
Research by Markus showed that after commit 4657a5301e ("realtek:
avoid busy waiting for RTL839x PHY read/write"), the ethernet driver
could only update a phy once per timer interval, which also heavily
impacted boot time. On e.g. a Zyxel GS1900-48, this added around a
minute to the time to fully initialise the switch.
By marking the otto clocksource as continuous, the kernel enables it to
be used for high resolution timers. This allows readx_poll_timeout() to
sleep for less than one system timer interval, reducing system dead
time.
Link: https://github.com/openwrt/openwrt/issues/11117
Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Cc: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> # Panasonic Switch-M48eG PN28480K
Tested-by: Jan Hoffmann <jan@3e8.eu> # HPE 1920-8G, HPE 1920-48G
The use of the adc_oe value stored in the efuse has been dropped in
MediaTek's SDK during a recent refactorization of the temperature
calculation formula. Don't ignore this offset value and again include
it in raw-to-deg-celsius calculation.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 16 MB SPI NOR
- Wi-Fi:
- MT7915DN + MT7905DAN: 2.4/5 GHz
- Ethernet: 1x 1GiE via MT7530
- UART: J4 (115200 baud)
- Pinout: [3V3] (TXD) (RXD) (GND)
- Bootloader: U-Boot
- Buttons:
- SW1 - no label on the box, combined with led
- Led: Status. RGB controlled by
- GPIO 14 - green color
- GPIO 15 - red color
- GPIO 16 - blue color
Installation:
OEM firmware is based on LEDE with custom UI and support standard sysupgrade
variant of firmware. However it requires "*.ubin" extension for sysupgrade file.
Always select "Factory reset" switch on upgrade to OpenWRT, otherwise
it will not boot.
MAC addresses as verified by OEM firmware:
vendor source
LAN factory 0x4 (label)
5g factory 0x4 (label)
2g label with flipped bits bit in 1-st byte and bits 5, 6, 7 in
4-th byte
Example
label: 44:xx:xx:b7:xx:xx
lan: 44:xx:xx:b7:xx:xx
2g 46:xx:xx:c7:xx:xx
5g 44:xx:xx:b7:xx:xx
Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
For kernel versions before 5.2, the required IPsec modes have to be
enabled explicitly (they are built-in for newer kernels).
Commit 1556ed155a ("kernel: mode_beet mode_transport mode_tunnel xfram
modules") tried to handle this, but it does not really work.
Since we don't support these kernel versions anymore and the code is
also broken, let's remove it.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[Remove old generic config options too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_PINCTRL_MCP23S08 configuration option is already unset in the
generic kernel configuration.
Fixes: f938512af6 ("target/at91: replace gpio-mcp23s08 with pinctrl-mcp23s08-spi update config")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the MikroTik RouterBOARD RBD53GR-5HacD2HnD
(hAP ac³ LTE6 kit), an indoor dual band, dual-radio 802.11ac
wireless AP with built-in Mini PCI-E LTE modem, one USB port, five
10/100/1000 Mbps Ethernet ports.
See https://mikrotik.com/product/hap_ac3_lte6_kit for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4019
- RAM: 256 MB
- Storage: 16 MB NOR
- Wireless:
· Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi internal antennae
· Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi internal antennae
- Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port
- 1x USB Type A port
- 1x Mini PCI-E port (supporting USB)
- 1x Mini PCI-E LTE modem (MikroTik R11e-LTE6, Cat.6)
Installation:
Make sure your unit is runnning RouterOS v6 and RouterBOOT v6 (tested on 6.49.6).
0. Export your MikroTik license key (in case you want to use the device with RouterOS later)
1. Boot the initramfs image via TFTP
2. Upload the "openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin" via SCP to the /tmp folder
3. Use sysupgrade to flash the image: sysupgrade -n /tmp/openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin
4. Recovery to factory software is possible via Netinstall:
https://help.mikrotik.com/docs/display/ROS/Netinstall
Signed-off-by: Csaba Sipos <metro4@freemail.hu>
The dependency on the kernel module gpio-mcp23s08 is replaced by
pinctrl-mcp23s08-spi and pinctrl-mcp23s08-i2c, as the gpio-mpc23s08 kernel
module no longer exists.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The kernel config option 'CONFIG_GPIO_MCP23S08' no longer exists.
Therefore, it is removed from the generic kernel configuration for
linux-5.10 and linux-5.15.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Adapt the device package to no longer use the gpio-mcp23s08 but instead
use the pinctrl-mcp23s08-spi. In addition, the kernel configuration was
adapted so that this can be built as a module and does not have to be
integrated directly into the kernel for this target.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Add support for the Linksys EA4500 v3 wireless router
Hardware
--------
SoC: Qualcomm Atheros QCA9558
RAM: 128M DDR2 (Winbond W971GG6KB-25)
FLASH: 128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN: QCA9558 3T3R 802.11 bgn
QCA9580 3T3R 802.11 an
ETH: Qualcomm Atheros QCA8337
UART: 115200 8n1, same as ea4500 v2
USB: 1 single USB 2.0 host port
BUTTON: Reset - WPS
LED: 1x system-LED
LEDs besides the ethernet ports are controlled
by the ethernet switch
MAC Address:
use address(sample 1) source
label 94:10:3e:xx:xx:6f caldata@cal_macaddr
lan 94:10:3e:xx:xx:6f $label
wan 94:10:3e:xx:xx:6f $label
WiFi4_2G 94:10:3e:xx:xx:70 caldata@cal_ath9k_soc
WiFi4_5G 94:10:3e:xx:xx:71 caldata@cal_ath9k_pci
Installation from Serial Console
------------
1. Connect to the serial console. Power up the device and interrupt
autoboot when prompted
2. Connect a TFTP server reachable at 192.168.1.0/24
(e.g. 192.168.1.66) to the ethernet port. Serve the OpenWrt
initramfs image as "openwrt.bin"
3. To test OpenWrt only, go to step 4 and never execute step 5;
To install, auto_recovery should be disabled first, and boot_part
should be set to 1 if its current value is not.
ath> setenv auto_recovery no
ath> setenv boot_part 1
ath> saveenv
4. Boot the initramfs image using U-Boot
ath> setenv serverip 192.168.1.66
ath> tftpboot 0x84000000 openwrt.bin
ath> bootm
5. Copy the OpenWrt sysupgrade image to the device using scp and
install it like a normal upgrade (with no need to keeping config
since no config from "previous OpenWRT installation" could be kept
at all)
# sysupgrade -n /path/to/openwrt/sysupgrade.bin
Note: Like many other routers produced by Linksys, it has a dual
firmware flash layout, but because I do not know how to handle
it, I decide to disable it for more usable space. (That is why
the "auto_recovery" above should be disabled before installing
OpenWRT.) If someone is interested in generating factory
firmware image capable to flash from stock firmware, as well as
restoring the dual firmware layout, commented-out layout for the
original secondary partitions left in the device tree may be a
useful hint.
Installation from Web Interface
------------
1. Login to the router via its web interface (default password: admin)
2. Find the firmware update interface under "Connectivity/Basic"
3. Choose the OpenWrt factory image and click "Start"
4. If the router still boots into the stock firmware, it means that
the OpenWrt factory image has been installed to the secondary
partitions and failed to boot (since OpenWrt on EA4500 v3 does not
support dual boot yet), and the router switched back to the stock
firmware on the primary partitions. You have to install a stock
firmware (e.g. 3.1.6.172023, downloadable from
https://www.linksys.com/support-article?articleNum=148385 ) first
(to the secondary partitions) , and after that, install OpenWrt
factory image (to the primary partitions). After successful
installation of OpenWrt, auto_recovery will be automatically
disabled and router will only boot from the primary partitions.
Signed-off-by: Edward Chow <equu@openmail.cc>
Manually rebased:
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
[Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128 MB
RAM: K4A4G165WF-BCWE 512 MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7976GN 2.4GHz ax 4x4
WiFi2: MT7976AN 5GHz ax 4x4
Button: Mesh, Reset
Flash instructions:
1. Gain ssh and serial port access, see the link below:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
2. Use ssh or serial port to log in to the router, and
execute the following command:
nvram set boot_wait=on
nvram set flag_boot_rootfs=0
nvram set flag_boot_success=1
nvram set flag_last_success=1
nvram set flag_try_sys1_failed=8
nvram set flag_try_sys2_failed=8
nvram commit
3. Set a static ip on the ethernet interface of your computer
(e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
4. Download the initramfs image, rename it to initramfs.bin,
and host it with the tftp server.
5. Interrupt U-Boot and run these commands:
setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
saveenv
tftpboot initramfs.bin
bootm
6. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Revert to stock firmware:
Restore mtdparts back to default, then use the
vendor's recovery tool (Windows only).
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
In rtl83xx_set_features we set bit 3 to enable, and bit 4 to disable
checksuming. Looking at rtl93xx_set_features we however see that for
both enable and disable the same bit is used (bit 4). This can't be
right, especially as bit 4 for rtl83xx seems to be Collision threshold
occupying 2 bits. Change this to make this more logical.
Fixes: 9e8d62e421 ("realtek: enable CRC offloading")
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.
Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.
The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.
Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.
The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
L2 learning on the CPU port is currently not consistently configured and
relies on the default configuration of the device. On RTL83xx, it is
disabled for packets transmitted with a TX header, as hardware learning
corrupts the forwarding table otherwise. As a result, unneeded flooding
of traffic for the CPU port can already happen on some devices now. It
is also likely that similar issues exist on RTL93xx, which doesn't have
a field to disable learning in the TX header.
To address this, disable hardware learning for the CPU port globally on
all devices. Instead, enable assisted learning to let DSA write FDB
entries to the switch.
For now, this does not sync local/bridge entries to the switch. However,
support for that was added in Linux 5.14, so the next switch to a newer
kernel version is going to fix this.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Initialize the data structure using memset to avoid the possibility of
writing garbage values to the hardware.
Always set a valid entry type, which should fix writing unicast entries
on RTL930x.
For unicast entries, set the is_static flag to prevent the switch from
aging them out.
Also set the rvid field for unicast entries. This is not strictly
necessary, as the switch fills it in automatically from a non-zero vid.
However, this makes the code consistent with multicast entry setup.
While at it, reorder the statements and fix some style issues (double
space, comma instead of semicolon at end of statement). Also remove the
unneeded priv parameter and debug print for the multicast entry setup
function.
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
This patch was wrongly dropped with the assumption that it was moved to
generic. This wasn't the case and caused the malfunction of the Asrock
G10 router.
Reintroduce it to fix Asrock G10 functionality.
Fixes: 8cc2caed58 ("ipq806x: 5:15: add testing kernel version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Zyxel NGB6817 is the only router that use mmc for rootfs. Upstream
kernel dtsi have mmc-ddr-1_8v enabled for sddc1. This is wrong as mmc on
ipq806x is supplied by a fixed 3.3v regulator and can't operate at 1.8v.
This cause the sddc1 to malfunction and cause kernel panic.
In old 5.15 version this was disabled but it was put in addition to many
other changes so it was dropped silently. Restore this patch to fix
working condition of such router.
Fixes: 88bf652 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Fixes: #11000
Tested-by: Hendrik Koerner <koerhen@web.de>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In refreshing DTS to the upstream version an unwanted change slipped in
the commit. The ASRock G10 dts got converted to DSA without any support.
Revert this to swconfig driver to restore normal functionality.
Fixes: 88bf652525 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
We currently ignore ret of the nandc partition parser if unprotected
spare data is true. This is the case for ipq806x nand.
Backport patch that fix this error and correctly handle error from
partition parser.
Fixes: ae6a63bc97 ("ipq806x: 5.15: replace nandc patch with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport patch from kernel 5.15 that mute error on EPROBE_DEFER with
smempart parser.
This parser require the smem device to be probed first and currently it
may happen that mtd gets probed before the smem device causing an error
on the smempart parser. This error may be confusing and should be muted.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In new kernel version from 5.16, smem node can be declared directly in
the reserved-space node. Upstream ipq806x (and to-be-merged) ipq807x
allign to this new implementation. Backport this patch to kernel 5.15 to
fix support for smem parser for ipq806x target.
Fixes: 88bf652525 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move patch wrongly placed in backport dir to pending dir as they still
didn't got merged upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move MGLRU patches from pending to backport as they got merged upstream.
These are direct porting from one of the dev so it's better to just move
than trying to backport them again from upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move mvebu aardvark patch from pending to backport as they got merged
upstream.
One additional patch is needed as a later fixup for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move sfp HALNy patch from pending to backport as they got merged
upstream. The patch was reordered and one was squashed in the upstream
variant.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The switches support different actions for incoming ethernet multicast
frames with Reserved Multicast Addresses (01-80-C2-00-00-{01-2F}). The
current code will set the 2-bit action field to FLOOD (0x3) for most
classes, but the highest bit is always unset for the relevant control
registers. This means the DROP (0x1) action being used for these
classes; whatever class the MSB happens to be in.
For RTL838x, this results in {20,23-2F} frames being dropped, instead of
flooding all ports. On other switch generations, {0F,1F,2F} frames are
dropped. This is inconsistent, and appears to be a mistake. Remove this
inconsistency by flooding all multicast frames with RMA addresses.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The multicast setup function rtl838x_eth_set_multicast_list() checks if
the current SoC is a RTL839x family device. However, the function is
only included in the RTL838x ops table, so this path should never be
taken, making this dead code. rtl839x_eth_set_multicast_list() is
already present in the RTL839x ops table, so it should be safe to remove
this branch.
While touching the code, also re-sort the functions to match sorting
elsewhere, with rtl838x coming before rtl839x.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Currently several messages at KERN_INFO level are printed for every FDB
del/dump operation. This can cause a significant slowdown for example
while using "bridge fdb", and may even trigger a watchdog.
Remove most of these log messages, as the new L2 table debugfs node
should be a good replacement. Change the remaining messages to
KERN_DEBUG level.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Switch to a polling implementation similar to the one for RTL838x, to
allow other kernel tasks to run while waiting.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The new timer is not yet ready for all targets. Avoid interactive
questions during build
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[rename symbol to CONFIG_REALTEK_OTTO_TIMER]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Use the new timer driver for the RTL839X devices and remove the
no longer needed modules.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct timer compatible order, update selected symbols]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Use the new timer driver for the RTL838X devices. Remove the no
longer needed modules.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct timer compatible order, update selected symbols]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Provide some helpful information about the devicetree configuration of
our new driver
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct compatible order in examples]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Now that we provide a clock driver for the Reltek SOCs the CPU frequency might
change on demand. This has direct visible effects during operation
- the CEVT 4K timer is no longer a stable clocksource
- after CPU frequencies changes time calculation works wrong
- sched_clock falls back to kernel default interval (100 Hz)
- timestamps in dmesg have only 2 digits left
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps ...
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.080000] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.090000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ...
Looking around where we can start the CEVT timer for RTL930X is a good basis.
Initially it was developed as a clocksource driver for the broken timer in that
specific SOC series. Afterwards it was shifted around to the CEVT location,
got SMP enablement and lost its clocksource feature. So we at least have
something to copy from. As the timers on these devices are well understood
the implementation follows this way:
- leave the RTL930X implementation as is
- provide a new driver for RTL83XX devices only
- swap RTL930X driver at a later time
Like the clock driver this patch contains a self contained module that is SOC
independet and already provides full support for the RTL838X, RTL839X and
RTL930X devices. Some of the new (or reestablished) features are:
- simplified initialization routines
- SMP setup with CPU hotplug framework
- derived from LXB clock speed
- supplied clocksource
- dedicated register functions for better readability
- documentation about some caveats
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[remove unused header includes, remove old CONFIG_MIPS dependency, add
REALTEK_ prefix to driver symbol]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Undo parts of these:
116feb4a1c ipq40xx: remove non-converted network configs
db19efee95 ipq40xx: disable boards not converted to DSA
Reintroduce the DT paths /soc/edma@c080000/gmac{0,1}, because the stock
bootloader has memorized them (instead of following aliases); then plug
the MAC address back in via 05_set_iface_mac_ipq40xx.sh, since the
'local-mac-address' property is no longer in the correct node.
Cc: David Bauer <mail@david-bauer.net>
Cc: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Convert to DSA and enable the MobiPromo CM520-79F device again.
Signed-off-by: Jack Chen <redchenjs@live.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
This fixes reference clock frequency of RB912. 25 MHz frequency leads
to system clock running too fast, uptime incrementing too fast and
delays (like `sleep 10`) returning too early.
Board has quartz with NSK 3KHAA Z 40 000 marking.
Signed-off-by: Pavel Kamaev <pavel@kamaev.me>
Manufacturer has predetermined mac address values for lan and wan ports.
This change keeps inline with other mt7621 devices mac address allocation
from factory mtd partition.
Example from hexdump output:
0xe000 0x6 (lan) - 0xe006 0x6 (wan)
0000e000 70 b3 d5 10 02 96 70 b3 d5 10 02 95 ff ff ff ff
Previous change had created an overlapping mac address situation as it
would increment by one based on the lan mac address location found in the
factory partition, which would sometimes increment to the same as the
mt7603 wifi chip.
Tested on Unielec u7621-01 model
Signed-off-by: David Bentham <db260179@gmail.com>
The hardware of Nokia A-040W-Q and RAISECOM MSG1500 X.00 are
exactly the same, both of which are customized by operators.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Add 6.1 tag to upstream patch now that 6.1 got tagged. This permits to
track patch in a better way and directly drop them on kernel bump.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
0001-MIPS-lantiq-add-pcie-driver.patch needs to drop
MODULE_SUPPORTED_DEVICE because that macro is gone on newer kernels.
Add checks for copy_{to,from}_user in
0008-MIPS-lantiq-backport-old-timer-code.patch which is now mandatory.
0705-v5.13-net-dsa-lantiq-allow-to-use-all-GPHYs-on-xRX300-and-.patch
get dropped because it's a backport from Linux 5.13.
All other patches are refreshed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This convert board asus,rt-ac42u to DSA and re-enable it
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Copy kernel config and patches from 5.10. Along with it
individual targets' config-default from 5.10 has been moved to
config-5.10.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Fix typo ('_' vs '-') and add #cooling-cells to gpio-fan to get
thermal zone into functional state.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should
be enabled on target or subtarget based on SoC architecture.
Fixes warning:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
...
.config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state
....
Summary:
- ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture.
If it is disabled then the processor operates in LITTLE_ENDIAN mode (default),
- ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This
option should be enabled after OpenWRT moves to kernel 6.x. After refreshing
the kernel, the symbol disappears,
- ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN,
- MIPS - enabled relevant symbols,
- POWERPC - enabled CONFIG_CPU_BIG_ENDIAN,
- UML - Symbols are not defined for this architecture,
- X86 - always little endian. Symbols are not defined for this architecture.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This comit fixes warnings that occur on kernel 5.15:
...
[ 2.269736] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 1e108000.switch-mii:00:
PHY has delays (e.g. via pin strapping), but phy-mode = 'rgmii'
[ 2.269736] Should be 'rgmii-id' to use internal delays txskew:1500 ps rxskew:1500 ps
...
Ref: be393dd685
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Just one device builds seama images so let's just fix up
seama on that one device. I guess the tool errors out but
this feels cleaner.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[rmilecki: drop "fixtrx" from D-Link case]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
On some of the hardware revisions of Asus RT-AC88U, brcmfmac detects the
4366b1 wireless chip and tries to load the firmware file which doesn't
exist because it's not included in the image.
Therefore, include firmware for 4366b1 along with 4366c0. This way, all
hardware revisions of the router will be supported by having brcmfmac use
the firmware file for the wireless chip it detects.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Add dependency to '32k' ADC clock so it is always enabled for thermal
and raw access to ADC values. This allows to remove the patch for the
ADC driver and reduce the patch adding thermal support for MT7986 to
only add the new efuse layout and temperature decoding for V3.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The most common CPU governor in the OpenWRT project is currently ondemand (see
below). Switch mt7622 over to it as well.
Audit the code by running the following and then analyzing the results:
find -name 'config-5.*' -print0 | xargs -0 grep 'CONFIG_CPU_FREQ_DEFAULT_GOV.*=y'
ondemand: 16
performance: 5
schedutil: 5
userspace: 2
Build system: x86_64
Build-tested: ramips/mt7621
Signed-off-by: John Audia <graysky@archlinux.us>
Remove kmod-sdhci-mtk as the mtk-sd driver is built-in anyway for the
relevant subtargets in order to support mounting rootfs from eMMC or
SD card.
Add kmod-iio-mt6577-auxadc to support reading the raw values from the
auxadc unit used as in-SoC thermal sensor. This driver was previously
built-in, but as thermal itself works well without it there is no use
for it in every day use of a device. Build the module to still allow
access to the raw values for those who need it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
As done previously, this preserves the MAC addresses of they physical
Ethernet ports. The interfaces are renamed as eth0 is in use for the
native GMAC; the new interface naming matches the physical port labels.
- sw-eth1 corresponds to the physical port labeled ETH1 and has the
base MAC address. This port can be used to power the device.
- sw-eth2 corresponds to the physical port labeled ETH2 and has a MAC
address one greater than the base.
As this device has 2 physical ports, they are each connected to their
respective PHYs, allowing the link status to be visible to software.
Since they are not marked on the case with any role (such as LAN or
WAN), both are bridged to the lan network by default, although this can
easily be changed if needed.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Get MAC address of WAN from HW.WAN.MAC.Address in hwconfig partition
instead of calculated one from wlan's address.
And added label_mac.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Use NVMEM "calibration" implementation for ath9k/ath10k(-ct) on ELECOM
WRC-300GHBK2-I and WRC-1750GHBK2-I/C instead of mtd-cal-data property
or user-space script.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Use ARTIFACTS to generate factory image of the following ELECOM devices
instead of redundant recipe which generate on KERNEL_INITRAMFS.
- ELECOM WRC-300GHBK2-I
- ELECOM WRC-1750GHBK2-I/C
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To use from the following devices in ath79 target, move edimax-header to
image-commands.mk.
- ELECOM WRC-300GHBK2-I
- ELECOM WRC-1750GHBK2-I/C
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Set 5.15 as default kernel. Testing support was already added on
29.03.2021.
Testing support was added in
9b3bc5d119 ("x86: enable 5.15 as testing kernel").
[0] - edd6021465
Tested-by: Mark Mentovai <mark@mentovai.com>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Don't reply on mapped rootfs partition but rather just take what ever
has been set to the kernel cmdline root= parameter as a hint to decide
which media to install sysupgrade to on the BananaPi BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* remove orphaned Kconfig symbol now that CONFIG_IIO is no longer
selected after commit ef8b935c95 ("mediatek: clean up mt7622 kernel config")
* select UBI fast-map feature to decrease boot time and keep the
number of spare blocks required in sync with U-Boot's expectations
(we got fast-map enabled in U-Boot)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patch headers and description for pending patch.
Add version tag to patch already merged upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This gets rid of "nvmem-cells" limitation. Dynamic partitions can be
defined for any (sub)partitions layout.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Add for mtd-parsers-trx-allow-to-use-on-MediaTek-MIPS-SoCs.patch and
hwmon-lm70-Add-ti-tmp125-support.patch the 5.18 tag as it was merged
in kernel 5.18.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add 6.1 tag to upstream patch now that 6.1 got tagged. This permits to
track patch in a better way and directly drop them on kernel bump.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Instead of trying to figure out the actual root device, just use the
kernel 'root' cmdline parameter as a hint to decide which device to
flash to.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use UBI fast map feature to avoid scanning the whole flash on each
boot which takes several seconds.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When I enabled CONFIG_HOTPLUG_PCI for mvebu platform, it was asking for
more symbols.
Fixes:
Support for PCI Hotplug (HOTPLUG_PCI) [Y/?] y
CompactPCI Hotplug driver (HOTPLUG_PCI_CPCI) [N/y/?] n
SHPC PCI Hotplug driver (HOTPLUG_PCI_SHPC) [N/y/?] (NEW)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.
Fixes: #10645
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Similar to the lzma-loader on our MIPS targets, the spi-loader acts as
a second-stage loader that will then load and start the actual kernel.
As the TL-WDR4900 uses SPI-NOR and the P1010 family does not have support
for memory mapping of this type of flash, this loader needs to contain a
basic driver for the FSL ESPI controller.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport qca8k fixup patches for inband mgmt on Big-Endian systems.
This is needed for ath79 and mpc85xx targets that are Big-Endian and use
qca8k based switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Raising the temperatures for passive and active trips. @VA1DER
proposed at issue 9396 to remove passive trip. This commit relates to
his suggestion.
Without this patch. the CPU will be throttled all the way down to 98MHz
if the temperature rises even a degree above the trip point, and it was
further discovered that if the internal temperature of the device is
above the first trip point temperature when it boots then it will start
in a throttled state and even
$ echo disabled > /sys/class/thermal/thermal_zone0/mode
will have no effect.
The patch increases the passive trip point and active cooling map. The
throttling temperature will then be at 77°C and 82°C, which is still a
low enough temperature for ARM devices to not be in the real danger
zone, and gives some operational headroom.
Signed-off-by: Bruno Umuarama <anonimou_eu@hotmail.com>
