Mediatek EIP93 Crypto engine is a crypto accelerator which
is available in the Mediatek MT7621 SoC.
Signed-off-by: Aviana Cruz <gwencroft@proton.me>
Co-authored-by: Richard van Schagen <vschagen@icloud.com>
Co-authored-by: Chukun Pan <amadeus@jmu.edu.cn>
Add 2 seconds sleep after each forcibly killed/tried-to-kill process
in the final process termination loop in sysupgrade stage2.
This is needed especially for qualcommax/ipq807x, where ath11k
wireless driver may have a long 10-20 seconds delay after termination
before actually getting killed. This often breaks sysupgrade.
The current KILL loop in kill_remaining does all 10 kill attempts
consecutively without any delay, as evidenced here in a failing sysupgrade.
It does not allow any time for the process to finalize its internal
termination.
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending TERM to remaining processes ...
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending signal TERM to hostapd (2122)
Sat Sep 2 19:05:56 EEST 2023 upgrade: Sending signal TERM to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending KILL to remaining processes ...
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2122)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Sending signal KILL to hostapd (2138)
Sat Sep 2 19:06:00 EEST 2023 upgrade: Failed to kill all processes.
sysupgrade aborted with return code: 256
The change in this commit adds a 2 seconds delay after each kill attempt
in order to allow some processes to more gracefully handle their
internal termination.
The result is like this:
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending TERM to remaining processes ...
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending signal TERM to hostapd (2309)
Sun Sep 3 11:15:10 EEST 2023 upgrade: Sending signal TERM to hostapd (2324)
Sun Sep 3 11:15:14 EEST 2023 upgrade: Sending KILL to remaining processes ...
Sun Sep 3 11:15:14 EEST 2023 upgrade: Sending signal KILL to hostapd (2309)
[ 699.827521] br-lan: port 7(hn5wpa2r) entered disabled state
[ 699.908673] device hn5wpa2r left promiscuous mode
[ 699.908721] br-lan: port 7(hn5wpa2r) entered disabled state
[ 701.038029] br-lan: port 6(hn5wpa3) entered disabled state
Sun Sep 3 11:15:16 EEST 2023 upgrade: Sending signal KILL to hostapd (2324)
[ 702.058256] br-lan: port 5(hn2wlan) entered disabled state
[ 709.250063] stage2 (8237): drop_caches: 3
Sun Sep 3 11:15:25 EEST 2023 upgrade: Switching to ramdisk...
The delay introduced here only kicks in if there is some process that
does not get terminated by the first TERM call. Then there is at least
one 2 sec wait after the first KILL loop round.
This commit is related to discussion in PRs #12235 and #12632
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Reviewed-by: Robert Marko <robimarko@gmail.com>
When the membase and pci_dev pointer were moved to a new struct in priv,
the actual membase users were left untouched, and they started reading
out arbitrary memory behind the struct instead of registers. This
unfortunately turned the RNG into a constant number generator, depending
on the content of what was at that offset.
To fix this, update geode_rng_data_{read,present}() to also get the
membase via amd_geode_priv, and properly read from the right addresses
again.
Closes#13417.
Reported-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Tested-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Suggested-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix PSE port assignment for 3rd GMAC on MT7988 and make sure dma_addr
is always initialized to prevent potentially accessing uninitialized
stack memory in the error path.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ALFA Network AX1800RM (FCC ID: 2AB877621) is a dual-band Wi-Fi 6
(AX1800) router, based on MediaTek MT7621A + MT79x5D platform.
Specifications:
- SOC: MT7621A (880 MHz)
- DRAM: DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash: 16 MiB SPI NOR (EN25QH128A-104HIP)
- Ethernet: 4x 10/100/1000 Mbps (SOC's built-in switch)
- Wi-Fi: 2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN)
(MT7905DAN doesn't support background DFS scan/BT)
- LED: 6x green, 1x green/red
- Buttons: 2x (reset, WPS)
- Antenna: 4x external, non-detachable omnidirectional
- UART: 1x 4-pin (2.54 mm pitch, J4, not populated)
- Power: 12 V DC/1 A (DC jack)
MAC addresses:
LAN: 00:c0:ca:xx:xx:4e (factory 0x4, +2)
WAN: 00:c0:ca:xx:xx:4f (factory 0x4, +3)
2.4 GHz: 00:c0:ca:xx:xx:4c (factory 0x4, device's label)
5 GHz: 00:c0:ca:xx:xx:4c (factory 0xa)
Flash instructions for web-based U-Boot recovery:
1. Power the device with WPS button pressed and wait around 10 seconds.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'recovery' image.
The device runs LEDE 17.01 (kernel 4.4.x) based firmware with 'failsafe'
mode available which allows alternative upgrade method:
1. Run device in 'failsafe' mode and change password for default user.
2. SSH to the device, transfer 'sysupgrade' image and perform upgrade
in forced mode, without preserving settings: 'sysupgrade -n -F ...'.
Other notes:
If you own early version of this device, the vendor firmware might
refuse OpenWrt image because of missing custom header. In that case,
ask vendor's customer support for stock firmware without custom header
support/requirement.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
With recent updates of TF-A the previously already fixed bug slipped
back into the source tree. Again, reorder bl2 init for MT7622 and
initialize WDT only after DRAM init has completed to avoid the
notorious hang.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Sync SPI-NAND/ECC controller driver for MT7622, MT7981, MT7986 and MT7988:
* Platform data for MT7981 was actually missing and is now added.
* Add support for Winbond W25N01KV 1Gbit chip.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Since kernel 5.13 this is needed to enable USB ports on all devices in
subtarget. Previously TF-A and COMPHY driver might have set up this PHY,
but not anymore.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com>
This should be a part of kernel major bump. Fortunately it didn't stall
compilation, so no fixes tag.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
| Layout: |
| :-------- |
| <Antenna> |
| VCC |
| GND |
| Tx |
| Rx |
**Flash instructions:**
1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.
**Notes:**
If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.
Signed-off-by: Patricia Lee <patricialee320@gmail.com>
Make use of minor sector size (4k) erasure on supported flash chips
to improve spi read/write performance.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
ath79 PCIe interrupt controller has stopped working correctly. This
is because the DT exposing a non-sensical interrupt-map property,
and their drivers relying on the kernel ignoring this property[1].
This patch fixes the PCIe init error:
ath9k 0000:00:00.0: of_irq_parse_pci: failed with rc=-14
Notice:
This is just a workaround, not a fix. PCIe driver and related dts
node need to be rewritten.
[1] https://lore.kernel.org/all/20211201114102.13446-1-maz@kernel.org/
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
All kernel configs are refreshed by
'make kernel_oldconfig CONFIG_TARGET=target' and
'make kernel_oldconfig CONFIG_TARGET=subtarget'.
upstreamed patches:
010-v5.17-spi-ar934x-fix-transfer-and-word-delays.patch
011-v5.17-spi-ar934x-fix-transfer-size.patch
020-v5.18-spi-ath79-Implement-the-spi_mem-interface.patch
030-v5.18-ath79-add-support-for-booting-QCN550x.patch
build and run tested on:
ath79/generic/ar7241
ath79/generic/qca9563
ath79/nand/ar9344
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Some symbols are outdated or missing due to daily kernel bumps. It's
better to re-add them. All configs are automatically refreshed by
'make kernel_oldconfig CONFIG_TARGET=taget' and
'make kernel_oldconfig CONFIG_TARGET=subtarget'
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This reverts commit 5356462ce5.
Kernel switching to fw_devlink=on as default broke probing some devices.
Revert it until we get a proper fix.
It seemed that mtd OF_POPULATED hack resolved probing issues but
apparently not all of them. We got reports about reading MAC using NVMEM
not working and USB controllers not working.
Ref: #10232Fixes: #13412
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fix the issue of dts buswidth cannot be applied properly with spi driver.
Fix the name of buswidth to bus-width in dts in order to fit the format
in linux spi kernel[1] so that spi-tx-bus-width & spi-rx-bus-width can be
parsed properly.
[1] Documentation/devicetree/bindings/spi/spi-controller.yaml
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
This adds support for Radxa ROCK Pi E, rockchip rk3328 board.
Specification:
- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
1 x 10/100/1000M Ethernet
1 x 10/100M Ethernet
- Storage:
1 x MicroSD Slot
1 x eMMC Module Slot
- USB Host/OTG:
1 x USB3.0 Type A HOST
1 x USB2.0 HOST (40-pin pin-header)
- Wireless
RTL8723DU/RTL8821CU
- Debug Serial:
1500000 baud at UART2 ( 40-pin pin-header)
- Power Supply:
Type-C 5V
Optionally PoE
Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
Add uboot support for Radxa ROCK Pi E, rockchip rk3328 board.
Add pre-built files to fix swig dependencies.
Specification:
- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
1 x 10/100/1000M Ethernet
1 x 10/100M Ethernet
- USB Host:
1 x USB3.0 Type A HOST
1 x USB2.0 OTG (40-pin pin-header)
- Wireless:
RTL8723DU/RTL8821CU
- Power Supply: Type-C 5V
Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
The bootcmd limits the kernel to 4 MiB which is
exceeded when using Device/FitImage. Device/FitzImage
reduces the size to around 3 MiB.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Bong <thomas.bong@devolo.de>
Renamed the interfaces to match the other devices.
Name the interface connected to the builtin G.hn chip 'ghn'.
This might toggle at runtime while the G.hn chip is in the
bootloader.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Bong <thomas.bong@devolo.de>
Changes:
9dc0800 wireless-regdb: Update regulatory rules for Philippines (PH)
111ba89 wireless-regdb: Update regulatory rules for Egypt (EG) from March 2022 guidelines
ae1421f wireless-regdb: Update regulatory info for Türkiye (TR)
20e5b73 wireless-regdb: Update regulatory rules for Australia (AU) for June 2023
991b1ef wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
When switching from a STA-only configuration to AP+STA on the same phy, the
STA was previously restarted in order to notify hostapd of the new frequency,
which might not match the AP configuration.
Fix the STA restart by querying the operating frequency from within hostapd
when bringing up the AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The NMBM-Enabled layout did not use fit image,
it just need default process. So it was been removed in platform.sh.
It will fix sysupgrade error for xiaomi,mi-router-wr30u-112m-nmbm.
Signed-off-by: Hank Moretti <mchank9999@gmail.com>
Remove stale sites from @GNOME alias:
* remove 2 sites that have stale 3 years old content
* remove 2 sites that have dropped GNOME
* convert 2 sites from FTP to HTTP
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
