When targets for multiple ESPRESSObin devices were added, not all
files were updated which means any ESPRESSObin version beside generic
won't have proper networking, sysupgrade and uboot-env. This patch
fixes the issue.
* fixup network detection
* fixup uboot-env
* fixup platform.sh for sysupgrade
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
(cherry picked from commit bc47285cb3)
Not all versions of ESPRESSObin require SD card, but can
be booted from the internal emmc flash (mmc dev 1) instead.
Add a simple check in the bootscript to see which mmc device
is detected and boot from it using mmcdev variable.
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
(cherry picked from commit 008b41b9b0)
An aquantia phy patch which dropped pause frame support was
missing when integrated LSDK-19.03 kernel patches into OpenWrt.
Without this patch, LS1043A 10G port would not work. So apply it.
Patch link
https://source.codeaurora.org/external/qoriq/qoriq-components/
linux/commit/?h=linux-4.14&id=66346b115818365cfaf99d292871b19f0a1d2850
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
"There are often transient line events when
the system is powered up and initialized and it
is often necessary for the gpio_chip driver to
clear any interrupt flags in hardware before
setting up the gpio chip, especially the
irqchip portions of it."
<http://lists.infradead.org/pipermail/openwrt-devel/2019-June/017630.html>
This patch adds a fix for the APM821XX's interrupt
controller to clear any bogus pending toggled
interrupts that happens on various APM821XX boards
on boot.
The patch also changes the debouce-interval from the
default 5ms debounce interval to 60ms all around.
The default setting caused on occasions that the button
state became stuck in a pressed state, even though the
button was released.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It seems that newer builds of OpenWRT have a gzip kernel
larger than 2MB~, which for some reason fails to boot on this board.
However, we have 8MB of kernel space and currently the uncompressed
kernel is 6.5MB~, so we have some space to grow until a better
solution is worked out.
Before:
## Booting kernel from Legacy Image at ee840000 ...
Image Name: Linux-4.19.53
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 2315724 Bytes = 2.2 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02000000 ...
Image Name: OpenWrt fake ramdisk
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux RAMDisk Image (uncompressed)
Data Size: 0 Bytes = 0 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at ec000000
Booting using the fdt blob at 0xec000000
Uncompressing Kernel Image ... Error: Bad gzipped data
GUNZIP: uncompress, out-of-mem or overwrite error -
must RESET board to recover
Loading Ramdisk to 10000000, end 10000000 ... OK
Loading Device Tree to 00ffa000, end 00fffc78 ... OK
ft_fixup_l2cache: FDT_ERR_NOTFOUND
After:
## Booting kernel from Legacy Image at ee840000 ...
Image Name: POWERPC OpenWrt Linux-4.19.53
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux Kernel Image (uncompressed)
Data Size: 6724584 Bytes = 6.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02000000 ...
Image Name: OpenWrt fake ramdisk
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux RAMDisk Image (uncompressed)
Data Size: 0 Bytes = 0 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at ec000000
Booting using the fdt blob at 0xec000000
Loading Kernel Image ... OK
OK
Loading Ramdisk to 10000000, end 10000000 ... OK
Loading Device Tree to 00ffa000, end 00fffc78 ... OK
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [75 cpl limit]
When OEM volumes are present in the [alt_]firmware partition,
sysupgrade will write a new kernel, but will fail to write
the root file system. The next boot will hang indefinitely
Waiting for root device /dev/ubiblock0_0...
Modified ipq40xx/base-files/lib/upgrade/linksys.sh
to remove both `squashfs` and `ubifs` if found
on the target firmware partition's UBI device.
Run-tested-on: Linksys EA8300
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[applied some shellcheck suggestions as well]
Follow upstream changes - header file changes
no executable difference at all
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 5273fb6b21)
Move all MikroTik devices to new function to increase script execution
speed.
Machine name in new version of MikroTik RouterBOARD devices add "RB"
before model name:
Old machine name: MikroTik RouterBOARD 951Ui-2nD
New: MikroTik RouterBOARD RB951Ui-2nD
So this patch should fix it for all currently supported MikroTik boards.
Tested-by: Cezary Jackiewicz <cezary@eko.one.pl> [wAP R-2nD]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[rebased,commit message facelift,script fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[spotted missing 922UAGS-5HPacD]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refreshed all patches.
Altered patches:
- 816-pcie-support-layerscape.patch
This patch also restores the initial implementation
of the ath79 perfcount IRQ issue. (78ee6b1a40)
It was wrongfully backported upstream initially and got reverted now.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
err_free_stats has been deprecated. Replace with err_netdev.
Compile-tested on: mvebu
Runtime-tested on: mvebu
Fixes: 4089df4f4b ("kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)")
Signed-off-by: George Amanakis <gamanakis@gmail.com>
[altered hashes]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 1e3800df18)
It's needed for applying some hardware quirks. This fixes:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/dmi.c:60:20: error: 'DMI_PRODUCT_SKU' undeclared here (not in a function); did you mean 'DMI_PRODUCT_UUID'?
DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "T8"),
Fixes: c52054e568 ("mac80211: brcm: backport remaining brcmfmac 5.2 patches")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 4d11c4c378)
Memory is allocated with devm_kzalloc() on every page program
and leaks until device is closed (which never happens).
Convert to kzalloc() and handle error paths manually.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Refreshed all patches.
This bump contains upstream commits which seem to avoid (not properly fix)
the errors as seen in FS#2305 and FS#2297
Altered patches:
- 403-net-mvneta-convert-to-phylink.patch
- 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch
Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* Remove testing patches for kernel version 4.19
* remove targets ar7, ixp4xx, orion
Those targets are still on kernel 4.9, patches for 4.14 were not ready
in time. They may be readded once people prepare and test patches for
kernel 4.14.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
01_leds has several redundant LED-cases. This commit cleans
up the file by merging these cases into shared cases.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
The TP-Link Archer C25 is a low-cost dual-band router.
Specification:
- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet
Some LEDs are controlled by an additional 74HC595 chip, but not
all of them as e.g. for the C59.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless
After commit 367813b9b1 the driver for RT5592 (rt2800pci)
is not selected by default anymore, which broke their 5GHz wireless
Add it back to device packages
Fixes: 367813b9b1 ("ramips: mt7620: fix dependencies")
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
When upgrading a TP-Link Archer C7 v2 from ar71xx to ath79,
the 5ghz radio stops working because the device path changed.
Some people subtitute the unsupported QCA9880v1 in the Archer v1
with supported QCA9880v2 radio. Since the stock radio doesn't
work, so it's safe to apply the change also for the Archer v1
images as well.
Also this patch renames the migration file and variables from
wmac to wifi.
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed comment, added return 0 (not that it matters since uci is
clever, see 00-wmac-migration thread), reworded commit message]
This patch harmonizes the label and alias for art partitions
across ath79. Since lower case seems to be more frequent, use that
consistently.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In commit c3a8518 eth0 and eth1 have been swapped for some devices,
but 11-ath10k-caldata has not been updated.
Instead of fixing this by swapping eth0/eth1, this patch will read
addresses from flash (as done for several devices already) so
adjustments due to eth order become obsolete.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The info/product-info partition, which frequently contains MAC
adresses, is typically assigned the 'info' alias in DTS, but
then labelled with 'info', 'product-info' or 'config'.
This leads to different aliases if used for setting MAC adresses
in DTS compared to when using e.g. mtd_get_mac_binary. Occationally,
also multiple switch-case entries are used just because of different
labelling.
This patch relabels those partitions in ath79 to consistently use
'info'.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Converts the TP-Link WDR4900 v1 to use the simpleImage in the
hopes of prolonging the life of the device. While at it,
the patch makes the fdt.bin an ARTIFACT and sets the KERNEL_SIZE
to 2684 KiB as a precaution since the stock u-boot is using a
fixed kernel size.
Note: Give the image some time, it will take much longer to
extract and boot.
[tested for 4.14/4.19]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Co-authored-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
In commit d2e18dae28 ("kirkwood: cleanup image build code") the image
build code was refactored, setting KERNEL_IN_UBI=0 which doesn't work as
the KERNEL_IN_UBI needs to be unset in order to make it working as
intended, which leads to factory images with two kernels in them:
binwalk --keep-going openwrt-kirkwood-cisco_on100-squashfs-factory.bin
MD5 Checksum: c33e3d1eb0cb632bf0a4dc287592eb70
DECIMAL HEX DESCRIPTION
-------------------------------------------------------------------------------
0 0x0 uImage header [...] "ARM OpenWrt Linux-4.14.123"
5769216 0x580800 uImage header [...] "ARM OpenWrt Linux-4.14.123"
Cc: Mathias Kresin <dev@kresin.me>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2285
Fixes: d2e18dae28 ("kirkwood: cleanup image build code")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The "bridge allow reception on disabled port" implementation
was broken after these commits:
08802d93e2 ("kernel: bump 4.19 to 4.19.37")
b765f4be40 ("kernel: bump 4.14 to 4.14.114")
456f486b53 ("kernel: bump 4.9 to 4.9.171")
This leads to issues when for example WDS is used, tied to a bridge:
[ 96.503771] wlan1: send auth to d4:5f:25:eb:09:82 (try 1/3)
[ 96.517956] wlan1: authenticated
[ 96.526209] wlan1: associate with d4:5f:25:eb:09:82 (try 1/3)
[ 97.086156] wlan1: associate with d4:5f:25:eb:09:82 (try 2/3)
[ 97.200919] wlan1: RX AssocResp from d4:5f:25:eb:09:82 (capab=0x11 status=0 aid=1)
[ 97.208706] wlan1: associated
[ 101.312913] wlan1: deauthenticated from d4:5f:25:eb:09:82 (Reason: 2=PREV_AUTH_NOT_VALID)
It seems upstream introduced a new patch, [1]
so we have to reimplement these patches properly:
target/linux/generic/pending-4.9/150-bridge_allow_receiption_on_disabled_port.patch
target/linux/generic/pending-4.14/150-bridge_allow_receiption_on_disabled_port.patch
target/linux/generic/pending-4.19/150-bridge_allow_receiption_on_disabled_port.patch
[1] https://lkml.org/lkml/2019/4/24/1228
Fixes: 08802d93e2 ("kernel: bump 4.19 to 4.19.37")
Fixes: b765f4be40 ("kernel: bump 4.14 to 4.14.114")
Fixes: 456f486b53 ("kernel: bump 4.9 to 4.9.171")
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
[updated commit message and title]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
ctinfo is a new tc filter action module. It is designed to restore
information contained in firewall conntrack marks to other packet fields
and is typically used on packet ingress paths. At present it has two
independent sub-functions or operating modes, DSCP restoration mode &
skb mark restoration mode.
The DSCP restore mode:
This mode copies DSCP values that have been placed in the firewall
conntrack mark back into the IPv4/v6 diffserv fields of relevant
packets.
The DSCP restoration is intended for use and has been found useful for
restoring ingress classifications based on egress classifications across
links that bleach or otherwise change DSCP, typically home ISP Internet
links. Restoring DSCP on ingress on the WAN link allows qdiscs such as
but by no means limited to CAKE to shape inbound packets according to
policies that are easier to set & mark on egress.
Ingress classification is traditionally a challenging task since
iptables rules haven't yet run and tc filter/eBPF programs are pre-NAT
lookups, hence are unable to see internal IPv4 addresses as used on the
typical home masquerading gateway. Thus marking the connection in some
manner on egress for later restoration of classification on ingress is
easier to implement.
Parameters related to DSCP restore mode:
dscpmask - a 32 bit mask of 6 contiguous bits and indicate bits of the
conntrack mark field contain the DSCP value to be restored.
statemask - a 32 bit mask of (usually) 1 bit length, outside the area
specified by dscpmask. This represents a conditional operation flag
whereby the DSCP is only restored if the flag is set. This is useful to
implement a 'one shot' iptables based classification where the
'complicated' iptables rules are only run once to classify the
connection on initial (egress) packet and subsequent packets are all
marked/restored with the same DSCP. A mask of zero disables the
conditional behaviour ie. the conntrack mark DSCP bits are always
restored to the ip diffserv field (assuming the conntrack entry is found
& the skb is an ipv4/ipv6 type)
e.g. dscpmask 0xfc000000 statemask 0x01000000
|----0xFC----conntrack mark----000000---|
| Bits 31-26 | bit 25 | bit24 |~~~ Bit 0|
| DSCP | unused | flag |unused |
|-----------------------0x01---000000---|
| |
| |
---| Conditional flag
v only restore if set
|-ip diffserv-|
| 6 bits |
|-------------|
The skb mark restore mode (cpmark):
This mode copies the firewall conntrack mark to the skb's mark field.
It is completely the functional equivalent of the existing act_connmark
action with the additional feature of being able to apply a mask to the
restored value.
Parameters related to skb mark restore mode:
mask - a 32 bit mask applied to the firewall conntrack mark to mask out
bits unwanted for restoration. This can be useful where the conntrack
mark is being used for different purposes by different applications. If
not specified and by default the whole mark field is copied (i.e.
default mask of 0xffffffff)
e.g. mask 0x00ffffff to mask out the top 8 bits being used by the
aforementioned DSCP restore mode.
|----0x00----conntrack mark----ffffff---|
| Bits 31-24 | |
| DSCP & flag| some value here |
|---------------------------------------|
|
|
v
|------------skb mark-------------------|
| | |
| zeroed | |
|---------------------------------------|
Overall parameters:
zone - conntrack zone
control - action related control (reclassify | pipe | drop | continue |
ok | goto chain <CHAIN_INDEX>)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make suitable adjustments for backporting to 4.14 & 4.19
and add to SCHED_MODULES_FILTER
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
All patches of LSDK 19.03 were ported to Openwrt kernel.
We still used an all-in-one patch for each IP/feature for
OpenWrt.
Below are the changes this patch introduced.
- Updated original IP/feature patches to LSDK 19.03.
- Added new IP/feature patches for eTSEC/PTP/TMU.
- Squashed scattered patches into IP/feature patches.
- Updated config-4.14 correspondingly.
- Refreshed all patches.
More info about LSDK and the kernel:
- https://lsdk.github.io/components.html
- https://source.codeaurora.org/external/qoriq/qoriq-components/linux
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to convert to use TF-A for firmware.
- Use un-swapped rcw since swapping will be done in TF-A.
- Use u-boot with TF-A defconfig.
- Rework memory map for TF-A introduction.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The WAN port has the wrong configuration in the kernel for the DVA-G3810BN/TL
The WAN port uses the internal phy, but it isn't enabled at the kernel board data.
Fix it.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This reverts commit 7c50182e0c.
Produces build error:
Package kmod-sched is missing dependencies for the following libraries:
nf_conntrack.ko
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
ctinfo is a new tc filter action module. It is designed to restore
information contained in firewall conntrack marks to other packet fields
and is typically used on packet ingress paths. At present it has two
independent sub-functions or operating modes, DSCP restoration mode &
skb mark restoration mode.
The DSCP restore mode:
This mode copies DSCP values that have been placed in the firewall
conntrack mark back into the IPv4/v6 diffserv fields of relevant
packets.
The DSCP restoration is intended for use and has been found useful for
restoring ingress classifications based on egress classifications across
links that bleach or otherwise change DSCP, typically home ISP Internet
links. Restoring DSCP on ingress on the WAN link allows qdiscs such as
but by no means limited to CAKE to shape inbound packets according to
policies that are easier to set & mark on egress.
Ingress classification is traditionally a challenging task since
iptables rules haven't yet run and tc filter/eBPF programs are pre-NAT
lookups, hence are unable to see internal IPv4 addresses as used on the
typical home masquerading gateway. Thus marking the connection in some
manner on egress for later restoration of classification on ingress is
easier to implement.
Parameters related to DSCP restore mode:
dscpmask - a 32 bit mask of 6 contiguous bits and indicate bits of the
conntrack mark field contain the DSCP value to be restored.
statemask - a 32 bit mask of (usually) 1 bit length, outside the area
specified by dscpmask. This represents a conditional operation flag
whereby the DSCP is only restored if the flag is set. This is useful to
implement a 'one shot' iptables based classification where the
'complicated' iptables rules are only run once to classify the
connection on initial (egress) packet and subsequent packets are all
marked/restored with the same DSCP. A mask of zero disables the
conditional behaviour ie. the conntrack mark DSCP bits are always
restored to the ip diffserv field (assuming the conntrack entry is found
& the skb is an ipv4/ipv6 type)
e.g. dscpmask 0xfc000000 statemask 0x01000000
|----0xFC----conntrack mark----000000---|
| Bits 31-26 | bit 25 | bit24 |~~~ Bit 0|
| DSCP | unused | flag |unused |
|-----------------------0x01---000000---|
| |
| |
---| Conditional flag
v only restore if set
|-ip diffserv-|
| 6 bits |
|-------------|
The skb mark restore mode (cpmark):
This mode copies the firewall conntrack mark to the skb's mark field.
It is completely the functional equivalent of the existing act_connmark
action with the additional feature of being able to apply a mask to the
restored value.
Parameters related to skb mark restore mode:
mask - a 32 bit mask applied to the firewall conntrack mark to mask out
bits unwanted for restoration. This can be useful where the conntrack
mark is being used for different purposes by different applications. If
not specified and by default the whole mark field is copied (i.e.
default mask of 0xffffffff)
e.g. mask 0x00ffffff to mask out the top 8 bits being used by the
aforementioned DSCP restore mode.
|----0x00----conntrack mark----ffffff---|
| Bits 31-24 | |
| DSCP & flag| some value here |
|---------------------------------------|
|
|
v
|------------skb mark-------------------|
| | |
| zeroed | |
|---------------------------------------|
Overall parameters:
zone - conntrack zone
control - action related control (reclassify | pipe | drop | continue |
ok | goto chain <CHAIN_INDEX>)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make suitable adjustments for backporting to 4.14 & 4.19
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This patch removes 202-reduce_module_size.patch which is causing missing
debug symbols in kernel modules, leading to unusable
kernel-debug.tar.bz2 on all platforms, making debugging of release
kernel crashes difficult.
Cc: Felix Fietkau <nbd@nbd.name>
Acked-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specifications:
- SoC: MT7628DAN (MT7628AN with 64MB built-in RAM)
- Flash: 8M SPI NOR
- Ethernet: 5x 10/100Mbps
- WiFi: 2.4G: MT7628 built-in
5G: MT7612E
- 1x miniPCIe slot for LTE modem (only USB pins connected)
- 1x SIM slot
Flash instruction:
U-boot has a builtin web recovery page:
1. Hold the reset button while powering it up
2. Connect to the ethernet and set an IP in 192.168.1.0/24 range
3. Open your browser and upload firmware through http://192.168.1.1
Note about the LTE modem:
If your router comes with an EC25 module and it doesn't show up
as a QMI device, you should do the following to switch it to QMI
mode:
1. Install kmod-usb-serial-option and a terminal software
(e.g. minicom or screen). All 4 serial ports of the modem
should be available now.
2. Open /dev/ttyUSB3 with the terminal software and type this
AT command: AT+QCFG="usbnet",0
3. Power-cycle the router. You should now get a QMI device
recognized.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Specifications:
- Atheros AR9331 (400 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 1T1R 2.4 Wlan (AR9331)
- 2x 10/100 Mbps Ethernet
- 3x LEDs, 1x gpio button
- 1x USB 2.0, 5V
- UART over usb, 115200n8
Upgrading from ar71xx target:
- Put image into board:
scp openwrt-ath79-generic-8dev_carambola2-squashfs-sysupgrade.bin \
root@192.168.1.1/tmp/
- Run sysupgrade
sysupgrade /tmp/sysupgrade.bin
Upgrading from u-boot:
- Set up tftp server with sysupgrade.bin image
- Go to u-boot (reboot and press ESC when prompted)
- Set TFTP server IP
setenv serverip 192.168.1.254
- Set device ip from same subnet
setenv ipaddr 192.168.1.1
- Copy new firmware to board
tftpboot 0x81000000 sysupgrade.bin
- erase flash
erase 0x9f050000 +${filesize}
- flash firmware
cp.b 0x81000000 0x9f050000 ${filesize}
- Reset board
reset
Signed-off-by: Rytis Zigmantavičius <rytis.z@8devices.com>
[wrapped long line in commit description, whitespace and art address
fix in DTS, keep default lan/wan setup, removed -n in sysupgrade]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
ZBT-WD323 is a dual-LTE router based on AR9344. The detailed
specifications are:
* AR9344 560MHz/450MHz/225MHz (CPU/DDR/AHN).
* 128 MB RAM
* 16MB of flash(SPI-NOR, 22MHz)
* 1x 2.4GHz wifi (Atheros AR9340)
* 3x 10/100Mbos Ethernet (AR8229)
* 1x USB2.0 port
* 2x miniPCIe-slots (USB2.0 only)
* 2x SIM slots (standard size)
* 4x LEDs (1 gpio controlled)
* 1x reset button
* 1x 10 pin terminal block (RS232, RS485, 4x GPIO)
* 2x CP210x UART bridge controllers (used for RS232 and RS485)
* 1x 2 pin 5mm industrial interface (input voltage 12V~36V)
* 1x DC jack
* 1x RTC (PCF8563)
Tested:
- Ethernet switch
- Wifi
- USB port
- MiniPCIe-slots (+ SIM slots)
- Sysupgrade
- Reset button
- RS232
Intallation and recovery:
The board ships with OpenWRT, but sysupgrade does not work as a
different firmware format than what is expected is generated. The
easiest way to install (and recover) the router, is to use the
web-interface provided by the bootloader (Breed).
While the interface is in Chinese, it is easy to use. First, in order to
access the interface, you need to hold down the reset button for around
five seconds. Then, go to 192.168.1.1 in your browser. Click on the
second item in the list on the left to access the recovery page. The
second item on the next page is where you select the firmware. Select
the menu item containing "Atheros SDK" and "16MB" in the dropdown close
to the buttom, and click on the button at the bottom to start
installation/recovery.
Notes:
* RS232 is available on /dev/ttyUSB0 and RS485 on /dev/ttyUSB1
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[removed unused poll-interval from gpio-keys, i2c-gpio 4.19 compat]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
also fix the following problems in this commit:
glinet,gl-ar150: This router uses an uncommon order of setting up gmacs
in ar71xx. gmac0 is preferred to be wan port because of
the additional link status info available. So this
router will have eth0/eth1 swapped comparing to ar71xx.
tplink,tl-wr710n-v1: same as gl-ar150
embeddedwireless,dorin: eth0 is used as switch port, which was incorrect.
It's correct now, so keep this one untouched.
tplink,tl-wr842n-v1: we don't swap PHYs on ar7241 so the original port order
is incorrect.
reorder archer-a7-v5 entry.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
With a proper probe deferring for ag71xx we don't need to explicitly
probe mdio1 before gmac0.
Drop all "simple-mfd" in SoC dtsi so that gmac orders can be the same
as ar71xx.
This makes eth0/eth1 order the same as those in ar71xx, which means
we don't need a migration script for this anymore and we can merge
incorrectly split gmac/mdio driver back together.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
gmac0 may need a phy on builtin switch, which can be unavailable
if gmac0 is probed before builtin switch.
Return -EPROBE_DEFER in this case so that gmac0 can be probed
later.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The original one has the following problem:
1. Port mask of lan led includes wan port.
2. By using netdev trigger with vlan port, the link led
is always on.
This commits fixes the above problems by correcting port
mask for lan led and use swconfig trigger for wan leds.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Support for D-Link DWR-118 A1 was added before LEDs feature
in mt76x0e driver.
This fixes the 5GHz WiFi LED which was previously inverted.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Remove references to broken and mostly deprecated phy_ethtool_ioctl, use
new {s,g}et_link_ksettings and add nway_reset which was previously
handled in phy_ethtool_ioctl.
Cc: John Crispin <john@phrozen.org>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=1982
Signed-off-by: Petr Štetiar <ynezz@true.cz>
ethtool doesn't work currently as phy_ethtool_ioctl expects user space
pointer, but it's being passed kernel one. Fixing it doesn't make sense
as {s,g}et_settings were deprecated anyway. So let's rather remove
phy_ethtool_ioctl and use new {s,g}et_link_ksettings instead. While at
it, update nway_reset as well.
Cc: John Crispin <john@phrozen.org>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=1982
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This ioctl is currently routed through generic interface code:
dev_ioctl
dev_ethtool
__ethtool_get_link_ksettings
phy_ethtool_ioctl
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This ioctl is currently routed through generic interface code:
dev_ioctl
dev_ethtool
__ethtool_get_link_ksettings
phy_ethtool_ioctl
Cc: John Crispin <john@phrozen.org>
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This ioctl is currently routed through generic interface code.
dev_ioctl
dev_ethtool
__ethtool_get_link_ksettings
phy_ethtool_ioctl
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Remove 701-phy_extension.patch from 4.14 and 4.19 kernel, as it's
currenlty broken and fixing doesn't make sense as most of it is
deprecated anyway.
Cc: John Crispin <john@phrozen.org>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=1982
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The register size of the QCA955x currently matches the size stated in
the datasheet. However, there are more hidden GMAC registers which are
needed for the SGMII workaround to work.
Signed-off-by: David Bauer <mail@david-bauer.net>
The R6220 and WNDR3700v5 are identical apart from using NAND/NOR flash and
having a different casing. This adds a new cleaned up R6220.dtsi with the
common bits for both devices. Both devices now have feature parity.
Performed cleanup:
* generic DTS node names
* regulator for usb power
* added missing pinctrl groups
* use switch port instead of VLAN as trigger for WAN LED
Fixes for WNDR3700v5:
* all LEDS work
* correct ethernet MAC addresses
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
- SoC: MediaTek MT7628AN
- Flash: 16MB (Winbond W25Q128JV)
- RAM: 64MB
- Serial: As marked on PCB, 3V3 logic, baudrate is 115200
- Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN)
- WIFI0: MT7628AN 2.4GHz 802.11b/g/n
- WIFI1: MT7612EN 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable power-LED (two-colored, yellow/blue)
Non-programmable internet-LED (shows WAN-activity)
- Buttons: Reset
INSTALLATION:
1. Connect to the serial port of the router and power it up.
If you get a prompt asking for boot-mode, go to step 3.
2. Unplug the router after
> Erasing SPI Flash...
> raspi_erase: offs:20000 len:10000
occurs on the serial port. Plug the router back in.
3. At the prompt select option 2 (Load system code then
write to Flash via TFTP.)
4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the
Server-IP.
5. Connect your computer to LAN1 and assign it as 192.168.1.2/24.
6. Rename the sysupgrade image to test.bin and serve it via TFTP.
7. Enter test.bin on the serial console and press enter.
Signed-off-by: Markus Scheck <markus@mscheck.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added mt76 compatible]
In ar71xx v2 has blue color defined because the same mach-*.c is also used
for TL-WDR4900 model with blue leds. ath79 v2 dts defines them as green.
For v4 the situation is the same as v5 so the conversion is identical only
v4 instead v5.
So now upgrading from ar71xx to ath79 should be also smoother for v2 and v4.
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas
Specifications:
MT7628 (580 MHz)
64 MB of RAM (DDR2)
8 MB of FLASH
2T2R 2.4 GHz (MT7628)
2T2R 5 GHz (MT7612E)
3x 10/100 Mbps Ethernet (2 LAN + 1 WAN)
2x external, non-detachable antennas (5dbi)
UART header on PCB (57600 8n1)
7x LED, 2x button
Known issues:
The Power LED is always ON, probably because it is connected
directly to power.
Flash instructions
------------------
Load the ...-factory.bin image via the stock web interface.
Openwrt upgrade instructions
----------------------------
Use the ...-sysupgrade.bin image for future upgrades.
Revert to stock FW
------------------
Warning! This tutorial will work only with the following OEM FW:
WR1000_EU_92.122.2.4987.201806261618.bin
WR1000_US_92.122.2.4987.201806261609.bin
If in the future these firmwares will not be available anymore,
you have to find the new XOR key.
1) Download the original FW from the Cudy website.
(For example WR1000_EU_92.122.2.4987.201806261618.bin)
2) Remove the header.
dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64
3) XOR the new file with the region key.
FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D
FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C
You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this:
xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767..
Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!):
https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false)
4) Check the resulting decrypted image.
Check if bytes from 0x20 to 0x3f are:
4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Alternatively, you can use u-boot's tool dumpimage tool to check
if the decryption was successful. It should look like:
# dumpimage -l stock-firmware.bin
Image Name: Linux Kernel Image
Created: Tue Jun 26 10:24:54 2018
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 4406635 Bytes = 4303.35 KiB = 4.20 MiB
Load Address: 80000000
Entry Point: 8000c150
5) Flash it via forced firmware upgrade and don't "Keep Settings"
CLI: sysupgrade -F -n stock-firmware.bin
LuCI: make sure to click on the "Keep settings" checkbox
to disable it. You'll need to do this !TWICE! because
on the first try, LuCI will refuse the image and reset
the "Keep settings" to enable. However a new
"Force upgrade" checkbox will appear as well.
Make sure to do this very carefully!
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added wifi compatible, spiffed-up the returned to stock instructions]
This patch fixes the active_low setting and
converts all of the physical keys on the wndr4700
to utilize the interrupt-driven gpio-keys driver
over the polled version.
The sdcard-insertion hack has been removed since the
block-subsystem will now be polling the device instead.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds support for kernel 4.14 to the target and directly make it the
default kernel version to use.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
Instead of maintaining 3 very similar subtargets merge them into one.
This does not use the Arm NEON extension any more, because the SAMA5D3
does not support NEON.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
This removes some settings which are normally set by the generic
configuration and should not be changed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
The configuration of the sama5d4 subtarget was used as the default
configuration and then the subtarget configurations were adapted.
The resulting kernel configuration without any extra modules selected is
still the same.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
The restart button is currently assigned to KEY_POWER power script but
an easily accessible button immediately powering off the device is
undesirable. Switch to using new KEY_POWER2 reboot script with 5 second
seen delay.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
This patch fixes following missing bits:
- add missing 'compatible' property on firmware partition
- set vendor partition 'userconfig' read-only
Fixes: 30dcbc741d ("ath79: add support for EnGenius ECB1750")
Signed-off-by: Sven Friedmann <sf.openwrt@okay.ms>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: AR9344
RAM: 128MB
Flash: 16MiB Winbond 25Q128BVFG SPI NOR
5GHz WiFi: AR9380 PCIe 3x3:3 802.11n
2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n
5x Gigabit ethernet via AR8327N switch (green + amber LEDs)
2x USB 2.0 via GL850G hub
4x front LEDs from SoC GPIO
1x front WPS button from SoC GPIO
1x bottom reset button from SoC GPIO
Known issues:
AR8327N LEDs only have default functionality, not presented in sysfs.
This is a regression from ar71xx.
UART header JP1, 115200 no parity 1 stop
TX
GND
VCC
(N/P)
RX
See https://openwrt.org/toh/wd/n750 for flashing detail.
Procedures unchanged from ar71xx.
Tested sysupgrade + factory flash from WD Emergency Recovery
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
This makes sysupgrade work on the D-Link DIR-685 after
initial factory install.
We create the platform.sh script to support sysupgrade
on more targets as we move on with sysupgrade support.
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[cleanup in platform.sh, removed superfluous SUPPORTED_DEVICES]
When running OpenWrt inside an LXC container no shell is opend as LXC
defaults to a virtual /dev/console.
This patch allows to enter a shell after starting the container via
`lxc-start`, without it is only posible to access a shell on tty1 via
`lxc-console`.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The vendor firmware only uses two mac addresses, the mac address on the
label and the label + 1. While checking multiple devices, all labels have
even mac addresses. Concluding only 2 address are assigned to a device.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The GL.iNet AR750S USB and microSD port is currently not working out of
the box. GPIO 7 is used to control the power of the USB port. Add GPIO
7 as a fixed-regulator for the port. Also add &usb1 to DTS to get the
microSD port to work.
Signed-off-by: Alexander Wördekemper <alexwoerde@web.de>
This patch fixes `sysupgrade -n` when flashed with rootfs of the same
size as currently running, so the rootfs_data wouldn't get destroyed and
thus survive reboot. So let's fix it by always cleaning up the content
of the rootfs_data during sysupgrade.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
ar71xx uses `archer-c7-v5` for led prefix, but ath79 sticks to more
generic `tplink` as the DTS is reused by more boards, so we need to
perform migrations of the LED names during upgrade.
Cc: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.
So this patch sets mib-poll-interval to 500ms on devices which are using
ar8xxx switch LEDs trigger, as the same value was set for built in
switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch").
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.
So this patch sets mib-poll-interval to 500ms on devices which have
ar83xx switch connected to emac0, as the same value was set for built in
switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch").
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.
So this patch sets mib-poll-interval to 500ms on devices which have
ar83xx switch connected to mdio0 bus, as the same value was set for
built in switches in 443fc9ac35 ("ath79: use ar8216 for builtin
switch").
Some measurements performed on TP-Link Archer C7-v5:
mib-type=0, mib-poll-interval=500ms (10s pidstat)
Average: %usr %system %guest %wait %CPU CPU Command
Average: 0.00 1.93 0.00 0.00 1.93 - kworker/0:2
iperf3 (30s): 334 Mbits/sec
mib-type=0, mib-poll-interval=2s (10s pidstat)
Average: %usr %system %guest %wait %CPU CPU Command
Average: 0.00 1.14 0.00 0.00 1.14 - kworker/0:2
iperf3 (30s): 334 Mbits/sec
So it seems like we get 4x faster LED refresh rate for additional 0.8%
CPU load.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
There are too many MIB counters that almost nobody needs since commit
d6366ce366 ("generic: ar8216: mib_work_func: read all port mibs
everytime").
In the worker function to poll MIB data, it deals with all ports instead
of only one port every time, which introduces too many mdio operations
that it becomes a heavy CPU load even on not-emulated MDIO bus.
This commit groups MIB counters and enable only TxBytes and RxGoodBytes
by default (both of which are necessary to get swconfig led working.)
and adds an swconfig attribute to allow enabling all counters if users
need them.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This allows specifying interval of polling MIB counters from userspace
and allow completely turning off MIB counter support by setting
mib_poll_interval to 0.
Since MIB counter polling is a heavy CPU load for GPIO emulated MDIO
bus, disable this behavior by default. Those who wants to use swconfig
LEDs can enable them with qca,mib-poll-interval dts property or with
swconfig command.
Fixes: FS#2230 ("kworker spikes 100% cpu every 2 second.")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The SD-Card polling is now implemented by default in the
fs-tools block-mount utility package. It might not be as
fast as the current detection method since the polling
time is 2 Seconds, but it's much less of an hack.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch converts the Range Extender to use the
interrupt-driven gpio-keys driver over the polled variant.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch converts the WNDR3700 to use the interrupt-driven
gpio-keys driver over the polled variant.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All other QCA9563 devices already use this identifier for
the exact SoC. Not that this matters much since as upstream
states in Documentation/devicetree/usage-model.txt:
"First and foremost, the kernel will use data in the DT to
identify the specific machine. In a perfect world, the
specific platform shouldn't matter to the kernel because all
platform details would be described perfectly by the device
tree in a consistent and reliable manner.
[...]
In the majority of cases, the machine identity is irrelevant,
and the kernel will instead select setup code based on the
machine's core CPU or SoC."
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
TP-Link Archer D50 v1 is a dual-band AC1200 router + modem.
The router section is based on Qualcomm/Atheros QCA9531 + QCA9882.
The "DSL" section is based on BCM6318 but it's currently not supported.
Internally eth0 is connected to the Broadcom CPU.
Router section - Specification:
CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB)
RAM: 64 MB (DDR2)
Flash: 8 MB (SPI NOR)
Wifi 2.4GHz: QCA9531 2T2R
Wifi 5GHz: QCA9982 2T2R
4x 10/100 Mbps Ethernet
8x LED, 3x button
UART header on PCB
Known issues:
DSL not working (eth0) (WIP)
UART connection
---------------
J2 HEADER (Qualcomm CPU)
. TX
. RX
. GND
O VCC
J16 HEADER (Broadcom CPU)
O VCC
. GND
. RX
. TX
The following instructions require a connection to the J2 UART header.
Flash instruction under U-Boot, using UART
------------------------------------------
1. Press any key to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Initramfs instruction under U-Boot for testing, using UART
----------------------------------------------------------
1. Press any key to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin
bootm 0x81000000
Restore the original firmware
-----------------------------
0. Backup every partition using the OpenWrt web interface
1. Download the OEM firmware from the TP-Link website
2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin)
3. Remove the U-Boot and the Broadcom image part from the file.
Issue the following command:
dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616
4. Double check the .mod file size. It must be 7995392 bytes.
5. Flash it using the OpenWrt web interface. Force the update if needed.
WARNING: Remember to NOT keep settings.
5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
Issue below commands in the U-Boot:
tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed
default-state = "off", it's already the default, added pcie node,
fixed typo]
SoC: Atheros AR7161-8C1A @ 680 MHz
RAM: 128MB - 2x Etron Technology EM6AB160TSA-5G
NOR: 16MB - 1x MXIC MX25L12845EMI-10G (SPI-NOR)
WI1: Atheros AR9223-AC1A 802.11bgn
WI2: Atheros AR9220-AC1A 802.11an
ETH: Atheros AR8021-BL1E + PoE
LED: Dual-Color Power/Status, Ethernet, WLAN2G and WLAN5G
BTN: 1 x Reset
I2C: AT97SC4303s TPM (needs driver!)
CON: RS232-level 8P8C/RJ45 Console Port - 9600 Baud
Factory installation:
- Needs a u-boot replacement. See Wiki for
information on how to do a in-circut flash with
a SPI-Flasher like a CH314A or flashrom. Wiki page
can be found at https://openwrt.org/toh/aruba/aruba_ap-105
- Be careful when dis- and reassembling the device to
not squish any of the antenna cables in the process!
- Be sure to make a full 16 MiB backup of your device
before flashing the new u-boot! This is needed if you
ever have interest in reverting back to stock firmware.
Not working:
- TPM (needs a driver)
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This uses the existing rules for Sercomm factory images and moves them
to the ramips image Makefile, so they can be used in all subtargets.
The new factory image for WNDR3700v5 can be flashed using nmrpflash.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Specifications:
- QCA9563 at 775 MHz
- 64 MB RAM Zentel A3R12E40CBF-8E
- 16 MB flash Winbond W25Q128FVSG
- 3 (non-detachable) Antennas / 450 Mbit
- 1x/4x WAN/LAN Gbps Ethernet (QCA8337)
- reset and Wi-Fi buttons
TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4,
except that the USB port has been removed and there is no longer a
removable antenna option. It also has different partitioning scheme.
The software is more in line with the Archer series in that it uses a
nested bootloader scheme.
(This has been adapted from the OpenWrt Wiki page)
<https://openwrt.org/toh/tp-link/tl-wr1043nd>
Installation on HW rev.5:
Factory firmware can be installed via the WEB interface.
Alternatively, it is also possible to use a TFTP server
for recovery purposes:
- Rename OpenWRT or original firmware to WR1043v5_tp_recovery.bin
- Set static IP of your PC to *192.168.0.66*
- Router will obtain IP 192.168.0.86 for a few seconds while
loading, when reset button pressed at power On.
And finally, there's always u-boot access through the UART.
For information visit the wiki.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[reworked commit message]
Using the same method as the D-Link DAP-2695 A1 we use
the "mtd" tool to augment the firmware checkum in flash
on first boot of a new firmware on the D-Link DIR-685.
We need to augment the Makefile for "mtd" to build in
the special WRGG fixup support for Gemini as well.
This works around the problem of the machine not booting
after factory install unless the sysupgrade is applied
immediately.
Based on commit e3875350f3
"ar71xx: add support for D-Link DAP-2695 rev. A1"
Cc: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Specification:
CPU: MT7628 580 MHz. MIPS 24K
RAM: 128 MB
Flash: 32 MB
WIFI: 802.11n/g/b 20/40 MHz
Ethernet: 5 Port ethernet switch
UART: 2x
Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART0 line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
set device and tftp server IP address and input the firmware
file name. U-boot will then load the firmware and write it into
the flash.
5. After firmware is started connect via ethernet at 192.168.1.1
Signed-off-by: Liu Yu <f78fk@live.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed dupped subject]
Specification:
- Qualcomm Atheros SoC QCA9558
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100/1000 Mbps Ethernet
- 3T3R 2.4 GHz (QCA9558 WMAC)
- 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH)
https://fccid.io/A8J-ECB1750
Tested and working:
- lan, wireless, leds, sysupgrade (tftp)
Flash instructions:
1.) tftp recovery
- use a 1GbE switch or direct attached 1GbE link
- setup client ip address 192.168.1.10 and start tftpd
- save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory
- plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed
- afterwards login via ssh and do a sysuprade
2.) oem webinterface factory install (not tested)
Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin".
3.) oem webinterface command injection
OEM Firmware already running OpenWrt (Attitude Adjustment 12.09).
Use OEM webinterface and command injection. See wiki for details.
https://openwrt.org/toh/engenius/engenius_ecb1750_1
Signed-off-by: sven friedmann <sf.openwrt@okay.ms>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[use interrupt-driven "gpio-keys" binding]
The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three,
independent radios. NAND provides two, alternate kernel/firmware
images with fail-over provided by the OEM U-Boot.
Installation:
"Factory" images may be installed directly through the OEM GUI.
Hardware Highlights:
* IPQ4019 at 717 MHz (4 CPUs)
* 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
* 256 MB RAM
* Three, fully-functional radios; `iw phy` reports (FCC/US, -CT):
* 2.4 GHz radio at 30 dBm
* 5 GHz radio on ch. 36-64 at 23 dBm
* 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm
#{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1
* All two-stream, MCS 0-9
* 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights
* USB3, single port on rear with LED
* WPS and reset buttons
* Four status lights on top
* Serial pads internal (unpopulated)
"Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1"
Implementation Notes:
The OEM flash layout is preserved at this time with 3 MB kernel and
~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and
syscfg (56 MB) partitions are untouched, available as read-only.
Serial Connectivity:
Serial connectivity is *not* required to flash.
Serial may be accessed by opening the device and connecting
a 3.3-V adapter using 115200, 8n1. U-Boot access is good,
including the ability to load images over TFTP and
either run or flash them.
Looking at the top of the board, from the front of the unit,
J3 can be found on the right edge of the board, near the rear
|
J3 |
|-| |
|O| | (3.3V seen, open-circuit)
|O| | TXD
|O| | RXD
|O| |
|O| | GND
|-| |
|
Unimplemented:
* serial1 "ttyQHS0" (serial0 works as console)
* Bluetooth; Qualcomm CSR8811 (potentially conected to serial1)
Other Notes:
https://wikidevi.com/wiki/Linksys_EA8300 states
FCC docs also cover the Linksys EA8250. According to the
RF Test Report BT BR+EDR, "All models are identical except
for the EA8300 supports 256QAM and the EA8250 disable 256QAM."
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Consistently handle boot-count reset and upgrade across
ipq40xx, ipq806x, kirkwood, mvebu
Dual-firmware devices often utilize a specific MTD partition
to record the number of times the boot loader has initiated boot.
Most of these devices are NAND, typically with a 2k erase size.
When this code was ported to the ipq40xx platform, the device in hand
used NOR for this partition, with a 16-byte "record" size. As the
implementation of `mtd resetbc` is by-platform, the hard-coded nature
of this change prevented proper operation of a NAND-based device.
* Unified the "NOR" variant with the rest of the Linksys variants
* Added logging to indicate success and failure
* Provided a meaningful return value for scripting
* "Protected" the use of `mtd resetbc` in start-up scripts so that
failure does not end the boot sequence
* Moved Linksys-specific actions into common `/etc/init.d/bootcount`
For upgrade, these devices need to determine which partition to flash,
as well as set certain U-Boot envirnment variables to change the next
boot to the newly flashed version.
* Moved upgrade-related environment changes out of bootcount
* Combined multiple flashes of environment into single one
* Current-partition detection now handles absence of `boot_part`
Runtime-tested: Linksys EA8300
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[checkpatch.pl fixes, traded split strings for 80+ chars per line]
Modify the title to match the following format, as it's enough
to uniquely identify a device:
<manufacturer> <model>
This matches what's done for other targets and has the
added benefit of creating a sorted-by-manufacturer list
of devices on menuconfig
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the
following specifications:
- MT7620A (580 MHz)
- 128MB RAM
- 32MB of flash (SPI NOR)
- 5x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus)
- 2x SIM card slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 10x LEDs (4 GPIO-controlled)
- 1x reset button
The following have been tested and working:
- Ethernet switch
- wifi
- miniPCIe slot
- USB port
- microSD slot
- sysupgrade
- reset button
Installation and recovery:
In order to install OpenWRT the first time or recover the router, you
can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address. Upload the firmware to start the recovery
process.
How to swap SIMs:
You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio13/value. In order for the change to take effect,
you can either use AT-commands (AT+CFUN) or power-cycle the modem (write
0/1 to /sys/class/gpio/gpio14/value).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed
specifications are:
- MT7620A (580MHz)
- 64MB RAM
- 16MB of flash (SPI NOR)
- 6x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM
SIM7100E LTE modem.
- 2x SIM slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 1x 5GHz wifi (mt7612)
- 1x reset button
- 1x WPS button
- 3x GPIO-controllable LEDs
- 1x 10 pin terminal block (RS232, RS485, 4 x GPIO)
Tested:
- Ethernet switch
- Wifi
- USB slot
- SD card slot
- miniPCIe-slot
- sysupgrade
- reset button
Installation instructions:
Installing OpenWRT for the first time requires a bit of work, as the
board does not ship with OpenWRT. In addition, the bootloader
automatically reboots when installing an image over tftp. In order to
install OpenWRT on the HDRM200, you need to do the following:
* Copy the initramfs-image to your tftp-root (default filename is
test.bin) and configure networking accordingly (default server IP is
10.10.10.3, client 10.10.10.123). Start your tftp server.
* Open the board and connect to UART. The pins are exposed and clearly
marked.
* Boot the board and press 1.
* Either use the default filename and client/server IP-addresses, or
specify your own.
The image should now be loaded to memory and board boot. If the router
reboots while the image is loading, you need to try again. Once the
board has booted, copy the sysupgrade-image to the router and run
sysupgrade in order to install OpenWRT to the flash.
Notes:
- You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio0/value. In order for the change to take
effect, you can either use AT-commands (AT+CFUN) or power-cycle the
modem (write 0/1 to /sys/class/gpio/gpio21/value).
- RS485 is available on /dev/ttyS0.
- RS232 is available on /dev/ttyS1.
- The name of the ioX-gpios map to the labels on the casing.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[fixed whitespace issue and merge conflict in target.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
These dts itself are incomplete (e.g. missing mtd partitions) and its
deivce support is never added to ath79 target.
Drop these unused dts for now.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
In commit e9652e1696 ("ath79: fix pinmux for ar933x devices") I've
wrongly changed desired register value to 0xf8 although it should've
been set to 0x0.
0xf8 value sets bits 3-7 (ETH_SWITCH_LEDx_EN) to 1 which actually
enables ethernet switch LEDs, so 0x0 is correct value in order to use
the pins as GPIO.
Fixes: e9652e1696 ("ath79: fix pinmux for ar933x devices")
Reported-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Simply dumped content of this regs in ar71xx and wrote them to DTS, as a
result port 6 on the switch will appear disconnected as on Archer C7v4.
[AS: testing and PORT6_STATUS fix]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Adds a new variable DISABLED_SERVICES to ImageBuilder Makefile, which
defines a list of services (installed as /etc/init.d/*) to be disabled
during the build of a custom image (normally all are enabled).
It comes handy when a particular service should not be run under normal
circumstances, but should be ready in the image for situations when it
might be needed.
Signed-off-by: Richard Musil <risa2000x@gmail.com>
Properly disable the SoC's internal Switch LEDs on the pinmux.
Devices that previously called ath79_gpio_function_disable for
the switch LEDs, just need to reference switch_led_pins in the
pinctrl-0 property of the gpio-leds node.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[changed desired pinctrl register value from 0x1f to proper 0xf8]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[renamed pinmux name to switch_led_disable_pins to make purpose more clear]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This devices have LEDs connected to the SoC's GPIOs, so it makes no
sense to fiddle with ar8327 LED regs.
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Network for the Archer C25 v1 is set up without switch for no
obvious reason. The LED setup is even done switch-based.
This patch changes network setup so a switch is created.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
for better identification. Also create SUPPORTED_DEVICES string from it
which corresponds to dts compatible string.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The driver is for the I2C mux.
Schematic available at https://doc.turris.cz/doc/_media/rtrom01-schema.pdf
Signed-off-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Tested-by: Rosen Penev <rosenp@gmail.com>
Commit eae6cac6a3 ("lantiq: add support for AVM FRITZ!Box 7362 SL"), but
one needs an initramfs image to flash OpenWrt from stock firmware (as
described in the commit log). This patch has the initramfs image built
by default.
Thanks to blogic (for pointing to the FEATURES declaration in the target
Makefiles) and Musashino on the forum for suggesting
config/Config-images.in needed editing too. While at it, reorder the
TARGET_INITRAMFS_COMPRESSION_LZMA declarations alphabetically.
This patch will result in initramfs images for all lantiq subtargets
that have the ramdisk flag set. I tested on the falcon and ase
subtargets, which lack that flag, to confirm they don't produce any
initramfs images with this patch - which they do not.
Given the limited scope of the lantiq (sub)target(s), blogic indicated
this should be OK.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[fixed the wrong reference to eae6cac6a3 commit]
OpenWrt is completely compiled from sources using a 64 bit compiler, we
do not need support for the old 32 bit MIPS interface on 64 Bit CPUs,
deactivate it.
Fixes: 46af22de16 ("kernel: Remove CONFIG_COMPAT")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
OpenWrt is completely compiled from sources using a 64 bit compiler, we
do not need support for the old 32 bit MIPS interface on 64 Bit CPUs,
deactivate it.
Fixes: 46af22de16 ("kernel: Remove CONFIG_COMPAT")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This moves some new configuration options to the generic kernel
configuration instead of configuring them for each target on our own.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes the following compilation issue that was introduced with the bump
to 4.14.118:
CC drivers/gpio/gpiolib-of.o
drivers/gpio/gpiolib-of.c: In function 'of_gpiochip_add':
drivers/gpio/gpiolib-of.c:510:12: error: too few arguments to function 'of_gpiochip_scan_gpios'
status = of_gpiochip_scan_gpios(chip);
^~~~~~~~~~~~~~~~~~~~~~
drivers/gpio/gpiolib-of.c:247:5: note: declared here
int of_gpiochip_scan_gpios(struct gpio_chip *chip, unsigned int start,
^~~~~~~~~~~~~~~~~~~~~~
scripts/Makefile.build:326: recipe for target 'drivers/gpio/gpiolib-of.o' failed
Fixes: 09050b6fe2 ("kernel: bump 4.14 to 4.14.118")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This target got bumped to 4.14 a long time ago
in commit: 2308b87204
Remove all leftover 4.9 files.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
CONFIG_HW_RANDOM_OMAP is not set to any value after kmod-random-omap was
removed, add the configuration option to the generic configuration.
Fixes: cd3b298533 ("omap24xx: Remove unmaintained target")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for different iterations of ESPRESSObin.
The added variants are:
ESPRESSObin with soldered eMMC,
ESPRESSObin V7, compared to V5 some passive elements changed and ethernet
ports labels positions have been reversed,
ESPRESSObin V7 with soldered eMMC.
Please refer to:
584d7c5 ("mvebu: new subtarget cortex A53")
for instruction how to boot OpenWrt image placed on SD card. It is
advised for owners of V5 and previous with bootloader based on U-Boot
2015.01, to upgrade the latest version available at:
http://espressobin.net/tech-spec.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Convert whole target to Device Tree based board detection instead of
identifying devices by dts file name. With this we can drop mvebu.sh
translation script and rely on common method for model detection.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Add vendors in device names and also rename few device names, for easier
identyfying potential firmware to flash. The vendor and device string is
mainly derived from model/compatipble string in dts from particular
device, but since not all devices are well described, some of the renames
follow marketing names.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Use make syntax to pass the U-Boot image location and boot with root
partitions size, instead of relying on shell functions and variables.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Drop overly complex amount of defines wich are referenced in the same
devices pool and move image recipes to common define, since devices not
using them overwrite it.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
All of U-Boot scripts repeat the same pattern with only Device Tree blob
name changing for respective device. Therefore create generic scripts
which will be altered on demad by image build process, and create
BOOT_SCRIPT variable which can be added to device recipe and will allow
referencing the same script by many device recipes. This will allow to
slim down the ammount of files in buildroot tree and avoid needlessly
incrementing amount of boot scripts if new devices will be added.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
All of arm64 devices have part of variables repeatedly defined. Stack
them to common define, and reference it in each device recipe.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Even if dts is not included in upstream Makefile, it is built anyway by
recipe specified in include/image.mk. Also remove Build/dtb, it's not
used since 3f72f3a ("mvebu: clearfog: include DTB for all variants in
image").
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This patch backports verbatim the commits from Linux 5.0 and 5.1
that implemented support for GigaDevice SPI NAND A and E variants.
Supported only in Linux 4.19 and later as based on the upstream
drivers/mtd/nand/spi/ framework.
mtd-spinand-add-support-for-GigaDevice-GD5FxGQ4xA.patch
commit c93c613214ac (5.0)
mtd-spinand-Add-support-for-GigaDevice-GD5F1GQ4UExxG.patch
commit c40c7a990a46 (5.1)
Run-tested-on: GL.iNet AR750S
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
This activates "Supervisor Mode Access Prevention". modern CPUs will
prevent the kernel code from accessing any data from the userspace
without the usage of copy_to_user() or copy_from_user()
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_BINFMT_MISC allows it to add support for new executable formats
to the kernel from user space, the kernel will then detect for example a
java binary and call the java execution program automatically. I am not
aware that this feature is used in OpenWrt and this could be used to
exploit something. Deactivate it for all targets for now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some targets deactivated CONFIG_SYN_COOKIES, for unknown reasons, use
the default setting from the generic configuration which activates
CONFIG_SYN_COOKIES.
This should prevent SYN flooding.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This removes support for executing old 32 bit applications on 64 bit ARM
and MIPS kernels.
On OpenWrt we normally compile all the user space applications on our
own and do not support third party binary only modules especial not 32
bit applications on 64 bit CPUs.
This reduces the attack surface on such systems and should also save
some memory.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These were renamed to CONFIG_STRICT_KERNEL_RWX and CONFIG_STRICT_MODULE_RWX and are
activated in kernel 4.14 and later by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates "Emulate Privileged Access Never using TTBR0_EL1
switching" on ARM64.
This should prevent the kernel from reading code from user space in
kernel context.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds additional checks to the copy_from_user() and copy_to_user()
functions. The details are described in this article:
https://lwn.net/Articles/695991/
This should only have a very small performance impact on system calls
and should not affect routing performance.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add some read-only properties to protect partitions from
accidental changes.
Also fixed two whitespaces error on the way.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The factory firmware omits the JFFS2 end-marker while flashing via
web-interface. Add a 64k padding after the marker fixes this problem.
When the end-marker is not present, OpenWRT won't save the overlayfs
after initial flash.
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
The correct board_name for the Turris Omnia is armada-385-turris-omnia.
Fixes: 4e8345ff68 ("mvebu: base-files: autodetect upgrade device")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Recently, upgrade device autodetection has been added to the mvebu target.
This exposes some shortcomings of the generic export_bootdevice function,
e.g. on the Turris Omnia: export_bootdevice silently reports the root
partition to be the boot device. This makes the sysupgrade process fail at
several places.
Fix this by clearly distinguishing between /proc/cmdline arguments which
specify the boot disk, and those which specify the root partition. Only in
the latter case, strip off the partition, and do it consistently.
root=PARTUUID=<pseudo PARTUUID for MBR> (any partition) and root=/dev/*
(any partition) are accepted.
The root of the problem is that the *existing* export_bootdevice in
/lib/upgrade/common.sh behaves differently, if the kernel is booted with
root=/dev/..., or if it is booted with root=PARTUUID=...
In the former case, it reports back major/minor of the root partition,
in the latter case it reports back major/minor of the complete boot disk.
Targets, which boot with root=/dev/... *and* use export_bootdevice /
export_partdevice, have added workarounds to this behaviour, by specifying
*negative* increments to the export_partdevice function.
Consequently, those targets have to be adapted to use positive increments,
otherwise they are broken by the change to export_bootdevice.
Fixes: 4e8345ff68 ("mvebu: base-files: autodetect upgrade device")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Extended mksenaofw to support new "capwap" header structure.
This supports flashing from factory 3.0.0, 3.0.1, 3.1.0 and 3.5.5
firmware.
Note that the factory image format changes for 3.1 and later firmware,
and that the 3.1.0 and 3.5.5 Engenius firmware will refuse the
factory_30.bin file. Similarly, the 3.0.0 and 3.0.1 Engenius firmware
will refuse the factory_35.bin file.
Flashing from the Engenius 3.1.0 firmware with the factory_35.bin
firmware has not been tested, as 3.1.0 firmware (Engenius "middleFW")
is only intended as part of the upgrade path to 3.5.5 firmware.
Modified ipq40xx image Makefile to appropriately invoke mksenaofw
with new parameters to configure the capwap header.
Note that there is currently no method to return to factory firmware,
so this is a one-way street.
Path from factory 3.0.0 and 3.0.1 (EnGenius) software to OpenWrt is
to navigate to 192.168.1.1 on the stock firmware and navigate to the
firmware menu. Then copy the URL you have for that page, something like
http://192.168.1.1/cgi-bin/luci/;stok=12345abcdef/admin/system/flashops
and replace the trailing /admin/system/flashops with just /easyflashops
You should then be presented with a simple "Firmware Upgrade" page.
On that page, BE SURE TO CLEAR the "Keep Settings:" checkbox.
Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_30.bin,
click "Upgrade" and on the following page select "Proceed".
Path from factory 3.5.5 (EnGenius) software to OpenWrt is simply to
use the stock firmware update menu. Choose the
openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_35.bin and click
"Upload" and "Proceed".
The device should then flash the OpenWrt firmware and reboot. Note
that this resets the device to a default configuration with Wi-Fi
disabled, LAN1/PoE acting as a WAN port (running DHCP client) and LAN2
acting as a LAN port with a DHCP server on 192.168.1.x (AP is at
192.168.1.1)
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[sorry, for unfixing the 80-lines eyesores.]
This patch works around an issue where reboot would cause the AP
to power down and not reboot.
The ipq4019 restart controller reboot causes the system
to power down and not recover. Fix is to disable the restart
controller in the device tree and the device reverts to
using the watchdog to perform the reset.
The real problem is due to the buggy bootloader that ships
with the device. Steve Glennon reported in the PR for this
patch: <https://github.com/openwrt/openwrt/pull/2009> that:
"the problem was due to a bad u-boot that ships with the device.
Using the u-boot that comes with 3.5.5.3 EnGenius factory
software now allows the old code (using the do_msm_reboot)
to reboot successfully.
On to the bad news:
Well 3.5.5.3 is a bad path. Finally managed to recover. You
CANNOT use prior EnGenius firmware to downgrade.
Findings:
* They now password protect the serial console with a new, unkown
password.
* They changed the protection on their walled-garden. I have to
use the ssh admin@ip /bin/sh --login to get out of their
walled-garden.
* Attempts to flash the original 3.0.0 or 3.0.1 EnGenius firmware
fail through the UI and sysupgrade. Their firmware update GUI now
seem to detect regular openwrt images, but they fail to flash
Attempts to flash a normal OpenWrt image with sysupgrade fail.
[..]
Attempts to sysupgrade with EnGenius firmware fail with the same
"mandatory section(s) missing" error, so you cannot downgrade to
3.0.0 or 3.0.1."
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added valuable
findings from github discussion]
Marvell sata controllers in all kirkwood SoCs support
sata port multipliers, just like mvebu.
Enable this feature in the default kernel config
so it is available in normal builds.
tested and working on nsa310b
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
If the target supports a newer kernel version that is not used by default
yet, it can be enabled with this option
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT7620 integrated WMAC does not need RT2x00 PCI driver or firmware
Also corrected kmod-eeprom-93cx6 and kmod-lib-crc-itu-t dependencies
according to original Kconfig and lsmod output
This will remove some unnecessary packages from MT7620 target to
save some space
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[75 characters per line in the commit message]
Switches failsafe mode interface from WAN to LAN ports.
Tested on TL-WR940Nv6.0 and TL-WR940Nv6.1
Signed-off-by: Joachim Fünfer <joachim.fuenfer@stusta.net>
This corrects the PLL value for 10 Mbit/s links on the OCEDO Raccoon.
Prior to this patch, 10 Mbit/s links would not transmit data.
It is worth mentioning that the vendor firmware used the same PLL
settings and 10Mbit/s was also not working there.
All other link-modes are working correctly without any packet loss.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit fixes following script error in syslog:
cat: can't open '/sys/devices/platform/ehci-platform/usb1/1-1/1-1.2/1-1.2:1.4/ieee80211/phy*/name': No such file or directory
sh: add: unknown operand
sh: add: unknown operand
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[commit subject and message tweaks]
Upstream has renamed UPROBE_EVENT to UPROBE_EVENTS in the following
commit:
commit 6b0b7551428e4caae1e2c023a529465a9a9ae2d4
Author: Anton Blanchard <anton@samba.org>
Date: Thu Feb 16 17:00:50 2017 +1100
perf/core: Rename CONFIG_[UK]PROBE_EVENT to CONFIG_[UK]PROBE_EVENTS
We have uses of CONFIG_UPROBE_EVENT and CONFIG_KPROBE_EVENT as
well as CONFIG_UPROBE_EVENTS and CONFIG_KPROBE_EVENTS.
Consistently use the plurals.
So I'm changing it to this plural option in order to make kconfig happy
and stop asking about it if kernel is compiled with verbose logging:
Enable uprobes-based dynamic events (UPROBE_EVENTS) [Y/n/?] (NEW)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
No target is using kernel 3.18 anymore, remove all the generic
support for kernel 3.18.
The removed packages are depending on kernel 3.18 only and are not used on
any recent kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 4.1, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target adds an alternative mmc driver using a patch.
Within this patch, a definition got renamed upstream.
Change it to fix following compile error:
CC drivers/mmc/host/bcm2835-mmc.o
In file included from ./include/linux/kernel.h:14:0,
from ./include/linux/delay.h:22,
from drivers/mmc/host/bcm2835-mmc.c:25:
drivers/mmc/host/bcm2835-mmc.c: In function 'bcm2835_mmc_dumpregs':
drivers/mmc/host/bcm2835-mmc.c:254:27: error: 'SDHCI_ACMD12_ERR' undeclared (first use in this function); did you mean 'SDHCI_CMD_CRC'?
bcm2835_mmc_readw(host, SDHCI_ACMD12_ERR),
^
./include/linux/printk.h:137:18: note: in definition of macro 'no_printk'
printk(fmt, ##__VA_ARGS__); \
^~~~~~~~~~~
drivers/mmc/host/bcm2835-mmc.c:253:2: note: in expansion of macro 'pr_debug'
pr_debug(DRIVER_NAME ": AC12 err: 0x%08x | Slot int: 0x%08x\n",
^~~~~~~~
drivers/mmc/host/bcm2835-mmc.c:254:27: note: each undeclared identifier is reported only once for each function it appears in
bcm2835_mmc_readw(host, SDHCI_ACMD12_ERR),
^
./include/linux/printk.h:137:18: note: in definition of macro 'no_printk'
printk(fmt, ##__VA_ARGS__); \
^~~~~~~~~~~
drivers/mmc/host/bcm2835-mmc.c:253:2: note: in expansion of macro 'pr_debug'
pr_debug(DRIVER_NAME ": AC12 err: 0x%08x | Slot int: 0x%08x\n",
^~~~~~~~
scripts/Makefile.build:326: recipe for target 'drivers/mmc/host/bcm2835-mmc.o' failed
make[8]: *** [drivers/mmc/host/bcm2835-mmc.o] Error 1
Upstream commit:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.14.114&id=45fd8679ea86bffb352132a1df4917c3d11375aa
Fixes: b765f4be40 ("kernel: bump 4.14 to 4.14.114")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Since ct->proto.tcp.last_win isn't updated when nf_ct_tcp_no_window_check is
enabled, the retransmission timeout check needs to be bypassed.
Based on patch by Rob Mosher
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The option is at the moment enabled for x86/64. The selection chain
should be
config RETPOLINE
select STACK_VALIDATION if HAVE_STACK_VALIDATION
config x86
select HAVE_STACK_VALIDATION if X86_64
cryptdev-linux:
make[4]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10'
make -C /store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.113 M=/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10 ARCH=x86 CROSS_COMPILE=x86_64-openwrt-linux-musl- modules
make[5]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.113'
make[6]: *** No rule to make target '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10/ioctl.o', needed by '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10/cryptodev.o'. Stop.
Makefile:1533: recipe for target '_module_/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/cryptodev-linux-cryptodev-linux-1.10' failed
Open vSwitch intree kmods
make[7]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux'
make -C /store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.111 ARCH=x86 M=/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux modules
make[8]: Entering directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.111'
make[9]: *** No rule to make target 'tools/objtool/objtool', needed by '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux/actions.o'. Stop.
Makefile:1533: recipe for target '_module_/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux' failed
make[8]: *** [_module_/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/openvswitch-2.11.0/datapath/linux] Error 2
make[8]: Leaving directory '/store/buildbot/slave/x86_64/build/sdk/build_dir/target-x86_64_musl/linux-x86_64/linux-4.14.111'
Reference: builddeb: include objtool binary in headers package, https://patchwork.kernel.org/patch/9014071/
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Refreshed all patches.
New symbols:
- CONFIG_LDISC_AUTOLOAD
- CONFIG_PPC_BARRIER_NOSPEC
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This patch fixes disfunctional WLAN LED on TP-Link W8970. The LED was
reported working in the CC release[1], but doesn't work anymore in 18.06.2.
1. 420cb24d41
Tested-by: Damian Janarek <dzanar18@o2.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Both targets have their own idea of how to use ehci-fsl.
This patch reverts part of commit
68b8d3b079 ("kernel: usb: add FSL EHCI package") and moves
ehci-fsl back into kmod-usb2, while also making it hopefully
useable for the mpc85xx target.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The current mpc85xx build is failing because the
TL-WDR4900v1 kernel image no longer fits into the
partition. Extending the kernel is not possible
without updating u-boot's kernel loader commands.
This patch disables the WDR4900v1 until the kernel
image size issue is fixed so the buildbot can still
compile the Sophos RED 15w Rev.1 . Installing the
WDR4900v1 images would cause the routers to get
bricked.
For the discussion, please go to:
<https://github.com/openwrt/openwrt/pull/1773>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently it's not possible to use perf on ath79 due to genirq flags
mismatch happening on static virtual IRQ 13 which is used for
performance counters hardware IRQ 5.
On TP-Link Archer C7v5:
CPU0
2: 0 MIPS 2 ath9k
4: 318 MIPS 4 19000000.eth
7: 55034 MIPS 7 timer
8: 1236 MISC 3 ttyS0
12: 0 INTC 1 ehci_hcd:usb1
13: 0 gpio-ath79 2 keys
14: 0 gpio-ath79 5 keys
15: 31 AR724X PCI 1 ath10k_pci
$ perf top
genirq: Flags mismatch irq 13. 00014c83 (mips_perf_pmu) vs. 00002003 (keys)
On TP-Link Archer C7v4:
CPU0
4: 0 MIPS 4 19000000.eth
5: 7135 MIPS 5 1a000000.eth
7: 98379 MIPS 7 timer
8: 30 MISC 3 ttyS0
12: 90028 INTC 0 ath9k
13: 5520 INTC 1 ehci_hcd:usb1
14: 4623 INTC 2 ehci_hcd:usb2
15: 32844 AR724X PCI 1 ath10k_pci
16: 0 gpio-ath79 16 keys
23: 0 gpio-ath79 23 keys
$ perf top
genirq: Flags mismatch irq 13. 00014c80 (mips_perf_pmu) vs. 00000080 (ehci_hcd:usb1)
This problem is happening, because currently statically assigned virtual
IRQ 13 for performance counters is not claimed during the initialization
of MIPS PMU during the bootup, so the IRQ subsystem doesn't know, that
this interrupt isn't available for further use.
So this patch fixes the issue by simply booking hardware IRQ 5 for MIPS PMU.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Reverting this commit as I've missed the fact, that the button is
already present in the included DTSI file.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or
Vocore2.
Specification:
CPU: MT7628 580 MHz. MIPS 24K
RAM: 64 MB
Flash: 8 MB
WIFI: 802.11n/g/b 20/40 MHz
USB: 1x Port USB 2.0
Ethernet: 5 Port ethernet switch
UART: 2x
Installation: Use the installed uboot Bootloader. Connect a serial cable
to serialport 0. Turn power on. Choose the option: "Load system code
then write to Flash via TFTP". Choose the local device IP and the TFTP
server IP and the file name of the system image. After if the
Bootloader will copy the image to the local flash.
Notes: The I2C Kernel module work not correctly. You can send and
receive data. But the command i2cdetect doesn’t work. FS#845
Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com>
[commit subject and message touches, DTS whitespace fixes, wifi LED
rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses,
removed i2c kernel modules]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
SoC: MediaTek MT7628NN
RAM: 64M DDR2 (Etron EM68B16CWQD-25H)
FLASH: 8M (Winbond W25Q64JVSIQ)
LED: Power - WLAN
BTN: Reset
UART: 115200 8N1
TX and RX are labled on the board as pads next to the SoC
Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
Note: The ethernet port is by default WAN. So you need to connect to
the router via WiFi
2. Navigate to the Update tab on the left side.
3. Select "Local Update"
4. Upload the OpenWrt sysupgrade image.
Note: Make sure you select not to preserve the configuration.
Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
Wait for the LED to flash 5 times.
2. Assign yourself a static IPv4 in 192.168.1.0/24
3. Upload the OpenWrt sysupgrade image at 192.168.1.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
TP-Link TL-WDR 4900 have u-boot with read-only env.
Boot command read only 0x29F000 data from flash.
Bigger images causes crc error. It can't be changed.
This patch add kernel size checking.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [utilize KERNEL_SIZE]
Remove wireless and USB packages from the device-specific package
selection as they are already selected by the target itself.
Signed-off-by: David Bauer <mail@david-bauer.net>
This removes USB support from the compiled kernel. Because of this, the
kernel is just small enough for the TP-Link WDR4900 to boot the
resulting kernel.
This is necessary to support the WDR4900 in the upcoming 19.xx release.
In the long run, this should be fixed with a second stage bootloader, as
the vendor bootloader only loads the first 2684k bytes.
Signed-off-by: David Bauer <mail@david-bauer.net>
I-O DATA ETG3-R is a wired router. So wireless-related packages are
unnecessary and remove those packages from default configuration to
reduce flash usage.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This adds support for the TP-Link WR842N v3 which is already supported on ar71xx
target (0b45bec22c).
Specification:
* SoC: QCA9533 ver 2 rev 0
* 16 MB Flash (gd25q128)
* 64 MB RAM
* 1 WAN 10/100 MBit/s (blue connector)
* 4 LAN 10/100 MBit/s (AR8229; 4 ports; yellow connectors)
* Atheros AR9531 (2,4GHz, two fixed antennas)
* USB
* Reset / WPS button
* WiFi button (rf kill)
* 8 green leds; 1 red/green led
* serial console (115200 8N1, according to the OpenWrt-wiki some soldering is needed)
Installation:
* flash via vendor WebUI (the filename must not exceed certain length)
* sysupgrade from installed OpenWrt (also ar71xx)
Thanks to Holger Drefs for providing the hardware
Tested-by: @kofec (github)
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
Instead of assigning I2C pins as GPIOs by default, leave it up to the
user whether to install kmod-i2c-mt7621 and use them for hardware I2C
instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is sold as a dual-band 802.11ac range extender. It has a sliding
switch for Extender mode or Access Point mode, a WPS button, a recessed
Reset button, a hard-power button, and a multitude of LED's, some
multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is
Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may
connect at 115200 bps, 8 data bits, no parity, 1 stop bit.
Specification:
- System-On-Chip: QCA9558
- CPU/Speed: 720 MHz
- Flash-Chip: Winbond 25Q128FVSG
- Flash size: 16 MiB
- RAM: 128 MiB
- Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3
- Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4
- PHY: Atheros AR8035-A
Installation:
If you can get to the stock firmware's firmware upgrade option, just feed
it the factory.img and boot as usual. As an alternative, TFTP the
factory.img to the bootloader.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[whitespace fix in DTS and reorder of make variables]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Remove Netgear-specific image build variables which are set to the same
value.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[reordering of variables, removed stray newline]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This device shares the network config with v4, thus the WAN MAC
also needs to be fixed the same way. However, the partition
where the MAC address resides has been changed.
Based on: https://github.com/openwrt/openwrt/pull/1726
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These devices share the network config with C7v4, thus the WAN MAC
also needs to be fixed the same way. However, the partition
where the MAC address resides has been changed.
Based on: https://github.com/openwrt/openwrt/pull/1726
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The GPIO for the reset button for the Archer C7v5 changed from
ar71xx to ath79. An investigation based on tests revealed
that the A7v5 responds on "11", while the C7v5 responds on
"5" as set for ar71xx.
Thus, we just define this in the DTS files instead of in the
common DTSI.
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Definition is split here without obvious reason. Just merge it
(and align order to that from C7 v4).
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal
2x2 MIMO antennas. It can be supplied via a USB connector or via PoE.
There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an
optional PoE passthrough from the first LAN port to the WAN port.
SoC: Qualcomm / Atheros QCA9533-BL3A
RAM: 64 MB DDR2
Flash: 16 MB SPI NOR
Ethernet: 4x 10/100 Mbps (1 WAN + 3 LAN)
LEDS: 1x via a SPI controller (not yet supported)
Buttons: 1x Reset
Serial: 1x (only RX and TX); 115200 baud, 8N1
Missing points:
- LED not yet supported
- Factory upgrade via web IF or TFTP recovery not yet supported
(Needs RSA signed images, for details see PR#1958)
The serial port is on a four pin connextor labeled J1 and located
between Ethernet and USB connector. The pinout is:
1. 3V3 (out)
2. Rx (in)
3. Tx (out)
4. GND
Upgrading via serial port / U-Boot:
- Connect the serial port via a level converter
- Power the system and stop U-Boot with pressing any key when `Hit any
key to stop autoboot` is displayed. Note: Pressing space multiple
times untill U-Boot reaches that location works well.
- Connect a PC with the IP 192.168.1.100 (or some other in that net)
running a TFTP-Server to one of the LAN ports. Copy the sysupgrade
image to the server.
- Set the U-Boot server IP with
setenv serverip 192.168.1.100
- Load the flash image to RAM with
tftpboot 0x81000000 sysupgrade.bin
- Erase the flash with
erase 0x9f050000 0x9ffaffff
- Write the new flash content with
cp 0x81000000 0x9f050000 ${filesize}
- Reset the device with
reset
Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
[removed full stop in subject and added lockdown note to commit message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SOC: Qualcomm Atheros QCA9558
RAM: 128MB
FLASH: 16MB (Macronix MX25L12845EMI-10G)
WLAN1: QCA9558 2.4GHz 802.11bgn 3SS
WLAN2: QCA9880 5GHz 802.11ac 3SS
LED: Power, LAN1, LAN2, 2.4GHz, 5GHz
Serial:Next to SPI Flash,
Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3)
The Serial setting is 115200-8-N-1
INSTALLATION:
1. Serve an OpenWrt ramdisk image named "ursus.bin".
Set your IP-address to 192.168.100.8/24.
2. Connect to the serial. Power up the device and interrupt
the boot process.
3. Set the correct bootcmd with
> setenv bootcmd run bootcmd_1
> saveenv
4. Run
> tftpboot 0x81000000 ursus.bin
> bootm 0x81000000
5. Wait for OpenWrt to boot up.
6. Transfer OpenWrt sysupdate image and flash via sysupgrade.
Signed-off-by: Markus Scheck <markus.scheck1@gmail.com>
Tested-by: David Bauer <mail@david-bauer.net>
[whitespace fix, renamed LED labels and SoC type fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In ar71xx we check for stuck DMA on devices which fall in the is_ar724x
SoC group (ar724x, ar933x, ar934x, qca9533, tp9343, qca955x, qca956x).
In ath79 we're currently performing this check only for devices with
ar7240 SoC, so this patch tries to sync the dma stuck checking behavior
with what is being done in ar71xx.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It was reported, that latest ar71xx builds have broken networking on
TP-Link TL-WPA8630 and Nanostation M5 XW devices and that by reverting
the offending commit, everything is back to normal.
Fixes: d3506d1 ("ar71xx: ag71xx: fix compile error when enabling debug")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART: 1 UART on PCB marked as J1 with 115200 8N1 config
LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
UART connection details
.---------------------------------.
| |
[ETH] J1 [ANT]
| o VCC o RX o TX o GND |
`---------------------------------'
Flashing instructions using recovery method over TFTP
1. Unplug the ethernet cable from the router.
2. Using paper clip press and hold the router's reset button. Make sure
you can feel it depressed by the paper clip. Do not release the button
until step 4.
3. While keeping the reset button pressed in, plug the ethernet cable
back into the AP. Keep the reset button depressed until you see the
device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
LED2/LED4), this may take up to 25 seconds.
4. You may release the reset button, now the device should be in TFTP
transfer mode.
5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
should work.
6. Plug the PoE injector's LAN cable directly to your computer.
7. Start tftp client and issue following commands:
tftp> binary
tftp> connect 192.168.1.20
tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin
Tested only on Bullet M2HP.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This is backport of the same functionality in ath79, from commit
d42a7c469 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP
recovery method")
Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:
All future airOS versions will be signed in this way and not allow
unsigned firmware to be loaded except via TFTP.
U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:
Hit any key to stop autoboot: 0
Setting default IP 192.168.1.20
Starting TFTP server...
Receiving file from 192.168.1.25:38438
Received 4981148 bytes
Firmware check failed! (1)
By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:
Received 3801500 bytes
Firmware Version: XW.ar934x.v6.0.4-42.OpenWrt-r9766+2-be42e44
Setting U-Boot environment variables
Un-Protected 1 sectors
Erasing Flash.... done
Patch provided by AREDN[3] project, tested on Bullet M2 XW.
1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points
2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt
3. https://github.com/aredn
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch adds support for the following computer on modules (CoM) from
Toradex[A]:
Apalis iMX6 Quad 2GB IT - i.MX 6Quad 800MHz, 2GB DDR3, 4GB eMMC
-40° to +85° C Temp
Apalis iMX6 Quad 1GB - i.MX 6Quad 1GHz, 1GB DDR3, 4GB eMMC
0° to +70° C Temp
Apalis iMX6 Dual 1GB IT - i.MX 6Dual 800MHz, 1GB DDR3, 4GB eMMC
-40° to +85° C Temp
Apalis iMX6 Dual 512MB - i.MX 6Dual 1GHz, 512MB DDR3, 4GB eMMC
0° to +70° C Temp
I've developed and tested it on Quad 2GB IT v1.1A and Dual 512MB v1.1A
CoMs, using Ixora[B] carrier board v1.0A, but it should hopefuly work on
Eval[C] board as well.
A. https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-freescale-imx-6
B. https://www.toradex.com/products/carrier-board/ixora-carrier-board
C. https://www.toradex.com/products/carrier-board/apalis-evaluation-board
Flashing/recovery instructions:
1. Download and compile imx_loader for OpenWrt from
https://github.com/ynezz/imx_loader
2. Enter recovery mode as desribed in
https://developer.toradex.com/knowledge-base/imx-recovery-mode
3. Connect board via USB to the host computer, check that it's connected
by lsusb:
15a2:0054 Freescale Semiconductor, Inc. i.MX 6Dual/6Quad SystemOnChip
in RecoveryMode
4. Copy following OpenWrt images to imx_loader directory:
SPL
u-boot.img
u-boot-with-spl.imx
openwrt-imx6-apalis-recovery.scr
openwrt-imx6-apalis-squashfs.combined.bin
5. Run imx_usb in imx_loader directory
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add switch definition for the rtl8367b switch to the DTS/DTSi for
the Belkin F9K1109v1 that was mistakenly omitted from the initial
commit.
Fixes: 017ec068e3 (ramips: add support for Belkin F9K1109v1)
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
Upstream driver has gone through a series of cleanup and was moved
from drivers/staging into drivers/spi. Backport it to replace our
messy driver.
Tested-by: Jörg Schüler-Maroldt <joerg-linux@arcor.de>
[LinkIt Smart 7688, AcSIP AI7688H Wi-Fi module]
Tested-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Tian Xiao bo <peterwillcn@gmail.com>
[Newifi-D2 MediaTek MT7621 ver:1 eco:3]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Currently, tplink-safeloader definition is only used a base for
another common definition.
This patch adjusts tplink-safeloader so it can be actually used
for some targets in generic-tp-link.mk.
This patch is cosmetic except for the order of
"check-size $$$$(IMAGE_SIZE)" and "append-metadata" exchanged
for the tplink_re350k-v1 .
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [dealed with
tplink_cpe210-v2 and tplink_cpe210-v3, removed tplink-safeloader-uimage's
extra IMAGE/sysupgrade.bin rule]
Enable the USB power for the Netgear R6120. Otherwise, no power is
supplied to an attached USB device.
Signed-off-by: David Bauer <mail@david-bauer.net>
With transition from ar71xx to ath79 some of devices change their naming
of LEDs. When upgrading from ar71xx target images this will require the
user to adjust previously working configuration. This commit adds
migration script which can be used to rename old names to new ones.
With this previously working configuration will be automatically
adjusted, wihtout user intervention.
This commit adds migration case for EnGenius EPG5000, the wireless LEDs
names have changed from epg5000:blue:wlan2-g and epg5000:blue:wlan-5g to
epg5000:blue:wlan2g and epg5000:blue:wlan5g.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Hardware spec:
CPU: MTK MT7621A
RAM: 256MB
ROM: 16MB SPI Flash
WiFi: MT7603EN + MT7612EN
Button: 2 buttons (reset, wps)
LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB)
Ethernet: 3 ports, 2 LAN + 1 WAN
Other: USB3.0
Flashing instructions:
Visit the openwrt forum topic for this router:
https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692
to get the bootloader and unlock firmware.
0. upgrade your router with the telnet firmware via the
firmware upgrade page on the webui.
1. telnet 192.168.11.1 from your PC
2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer
it to the /tmp directory of the router.
3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader
4. turn off the power
5. Push the reset button while turning on the router and
wait until LED start blinking (~10sec.)
6. Connect Ethernet port and goto http://192.168.1.1.
7. Upload the firmware to firmware restore page in webui.
Signed-off-by: Zhao Yu <574249312@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the
flashing instructions, fixed author]
This commit adds support for Linux 4.19 kernel, various cleanups
listed below.
Drop 170-cisco-hack.patch as these devices never seems to have been
supported.
Unset kernel symbols:
* CONFIG_CAVIUM_CN63XXP1=y
No supported hardware uses CN63XXP1 and it causes "slight decrease in
performance"
Source: https://cateee.net/lkddb/web-lkddb/CAVIUM_CN63XXP1.html
* CONFIG_USB_OCTEON_EHCI=y
CONFIG_USB_OCTEON_OHCI=y
Deprecated
Source: https://cateee.net/lkddb/web-lkddb/USB_OCTEON_EHCI.htmlhttps://cateee.net/lkddb/web-lkddb/USB_OCTEON_OHCI.html
Removed kernel symbols:
* # CONFIG_ARCH_HIBERNATION_POSSIBLE=y
* CONFIG_ARCH_SUSPEND_POSSIBLE=y
These are not in if you do a vanilla config of a MIPS Octeon kernel
and I can't find any references about support on this platform.
* # CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
* CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
No need to have this in by default, not defined in most other targets
* CONFIG_CRASH_CORE=y
Can't find any documentation why this should be enabled by default
* CONFIG_DEBUG_INFO=y
Set by https://github.com/openwrt/openwrt/blob/master/config/Config-kernel.in#L134
* CONFIG_DEBUG_SPINLOCK=y
No need to have this in by default
* CONFIG_DEFAULT_HUNG_TASK_TIMEOUT=120
Already set by default
Source: https://cateee.net/lkddb/web-lkddb/DEFAULT_HUNG_TASK_TIMEOUT.html
* CONFIG_DETECT_HUNG_TASK=y
No need to have this in by default, not defined in most other targets
* CONFIG_HAVE_DEBUG_KMEMLEAK=y
No need to have this in by default, not defined in most other targets
* CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
No need to have this in by default
* CONFIG_HAVE_IDE=y
None of the supported devices have IDE
* CONFIG_HZ=250
* # CONFIG_HZ_100 is not set
* CONFIG_HZ_250=y
This is broken with generic config
* CONFIG_KALLSYMS=y
No need to have this in by default, not defined in most other targets
* CONFIG_KEXEC=y
* CONFIG_KEXEC_CORE=y
No need to have this in by default, not defined in most other targets
* CONFIG_HAVE_KVM=y
No need to have this in by default
* CONFIG_SCHED_DEBUG=y
No need to have this in by default, not defined in most other targets
* CONFIG_SYSFS_DEPRECATED=y
Deprecated symbol
Source: https://cateee.net/lkddb/web-lkddb/SYSFS_DEPRECATED.html
* CONFIG_SYSFS_DEPRECATED_V2=y
Discouraged usage in general
Source: https://cateee.net/lkddb/web-lkddb/SYSFS_DEPRECATED_V2.html
* CONFIG_UNINLINE_SPIN_UNLOCK=y
No need to have this in by default, not defined in most other targets
Source: https://github.com/openSUSE/kernel/blob/master/lib/Kconfig.debug#L1137
* CONFIG_ZLIB_INFLATE=y
No need to have this in by default, not defined in most other targets
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Currently sysupgrade overwrites whole disk and destroys partitions added
by user. Sync the sysupgrade code with the one present in x86 target to
remedy this behaviour.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Since some boards could be also booted from other mediums than SD card,
lets make the upgrade block device autodetected.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Since most of devices using SD card image to boot, use ext4 as boot
files system we can drop fat fs related packages. Also move packages
which are added repeatedly across subtargets to their default packages,
with droping the ones that are enabled in target kernel configugation.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This will allow to drop additional packages and shrink image size.
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The options are managed on a generic way by the can
kmod packages
Additionally, select can packages only for devices that
currently has CAN enabled, which is only the ZC702
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The options are managed on a generic way by video packages
Additionally, only one of the currently supported boards
has a camera interface, but it requires programming
the FPGA fabric first
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The options are managed on a generic way by the sound
kmod packages
Additionally, none of the currently supported boards have
sound support out of the box, as they require programming
the FPGA fabric first
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
It is a small form factor computer with rich amount of expansion ports.
Some hardware specs and supported features in this commit:
CPU: NVIDIA Tegra 2 @ 1GHz
RAM: 1GB DDR2-667
Storage: SDHC card slot
µSDHC card slot
USB to SATA bridge (depends on model)
1MB SPI NOR flash for bootloader (single partition)
LAN: RTL8111DL GbE
WIFI: RT3070 b/g/n with external antenna (depends on model)
RTC: EM3027 (mapped as rtc0; with battery backup)
Tegra 2 built-in (mapped as rtc1)
Sound: Analog/Digital (TLV320AIC23b; S/PDIF not tested)
Connectors: 4x USB 2.0
RS232 (mini serial)
HDMI
DVI-D (depends on model, not supported atm)
Extension connector (24 pin ZIF, 0.5mm pitch):
2X UART
SPI
JTAG (1.8V)
Other: power button with green led (not functional for early revisions
without programmed PMIC)
2x GPIO configurable green led
TrimSlice uses U-Boot placed in NOR flash. Boots Linux from any media
connected to USB, SATA or SD card inserted in slot. Can also boot from
TFTP. To run OpenWrt one needs to update U-Boot to fairly recent version
(the versions, pre-dts/dts provided by CompuLab won't suffice):
1. Boot TrimSlice into Your current linux distro,
2. Download trimslice-spi.img from u-boot-trimslice subdir,
3. Install mtd-utils,
4. Run following commands:
flash_erase /dev/mtd0 0 256
nandwrite /dev/mtd0 trimslice-spi.img
5. Poweroff, insert SD card with OpenWrt, boot and enjoy.
If by some obstacle You can't follow those instructions, it is possible
to flash U-Boot using serial console.
1. Insert FAT or EXT2/EXT3 formatted SD card with trimslice-spi.img,
2. Interrupt boot process to enter U-Boot command line,
3. Run following commands:
${fs}load mmc 0 0x04080000 trimslice-spi.img
sf probe 0
sf erase 0 0x100000
sf write 0x04080000 0x0 ${filesize}
reset
4. Poweroff, insert SD card with OpenWrt, boot and enjoy.
If something went wrong with one of above steps, there is simple
recovery option:
1. Open the µSD slot security door to access the recovery-boot button,
2. Insert SD card with OpenWrt to the front slot while unpowered,
3. Power on the TrimSlice while pressing the recovery-boot button,
4. With this it should boot straigth to OpenWrt, from there download
trimslice-spi.img and execute following commands:
mtd erase /dev/mtd0
mtd write trimslice-spi.img /dev/mtd0
5. Reboot, now it should boot straigth to OpenWrt, without pressing the
recovery-boot button, with proper U-Boot flashed.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Add U-Boot for NVIDIA Tegra based boards, with the first being CompuLab
TrimSlice. This is part of initial support for this board.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
New target introduces initial support for NVIDIA Tegra SoC based devices.
It focuses on Tegra 2 CPUs, for successors supporting NEON instruction
set the target should be split in two subtargets.
This initial commit doesn't create any device image, it's groundwork
for further additions.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
It adjusts b53 code to upstream changes from the commit 3c1bcc8614db
("net: ethernet: Convert phydev advertize and supported from u32 to link
mode").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Please note that modified code isn't currently being compiled with
kernels 4.19+ due to the dropped CONFIG_NF_CONNTRACK_IPV6 in upstream
Linux. That requires a separated fix.
This fixes:
net/netfilter/nf_conntrack_rtcache.c: In function 'nf_rtcache_get_cookie':
net/netfilter/nf_conntrack_rtcache.c:82:11: error: 'const struct rt6_info' has no member named 'rt6i_node'; did you mean 'rt6i_idev'?
if (rt->rt6i_node)
^~~~~~~~~
rt6i_idev
IPv6 structs were reworked in upstream kernel by:
commit a64efe142f5e ("net/ipv6: introduce fib6_info struct and helpers")
commit 77634cc67dc1 ("net/ipv6: Remove unused code and variables for rt6_info")
commit 93c2fb253d17 ("net/ipv6: Rename fib6_info struct elements")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
This is based on the support patch for the identical CPE210 v3
by Mario Schroen <m.schroen@web.de>.
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specifications:
* SoC: Qualcomm Atheros QCA9533 (650MHz)
* RAM: 64MB
* Storage: 8 MB SPI NOR
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI or TFTP
To get to TFTP recovery just hold reset button while powering
on for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Thanks to robimarko for the work inside the ar71xx tree.
Thanks to adrianschmutzler for deep discussion and fixes.
Signed-off-by: Mario Schroen <m.schroen@web.de>
[Split into DTS/DTSI, read-only config partition in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename, light subject touches]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Looks identical to the v2.
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[Rebased, adjusted for separate tplink-safeloader entry, dynamic partitioning]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is also helpful to add support in ath79.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
I've missed leading whitespace issues in the original patch, so fixing
it in this commit. Thanks to pepe2k for letting me know.
Fixes: d260813d ("ar71xx: ens202ext: Fix VLAN switch")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This adds the SPDX license identifier for the NETGEAR EX6150. It was
missed when submitting the original patch.
Signed-off-by: David Bauer <mail@david-bauer.net>
The target ENS202EXT was just recently added right before the stable
release of Openwrt 18.
It flashes fine, but the physical switch is almost impossible to use
until you have a VLAN set up. Tested on two devices.
The actual problem is that eth0 represents nothing for whatever reason.
In other words, both WAN and LAN are running from eth1. There may be an
underlying problem in the build, but for now, I assume that this is
correct and that a VLAN switch is an appropriate fix.
Also, it's virtually impossible to get the switch running right through
LuCI. It is one thing to get a switch to appear, but attempting to
configure it breaks the whole thing. The VLAN has to be set up
perfectly, otherwise, interfaces will not start up, and one is forced to
reset settings, OR, the new LuCI feature kicks in and reverses any
steps. It is extremely difficult to determine which virtual ports
correspond to which physical ethernet ports without being able to set up
the switch in LuCI.
Temporary Workaround: followed directions here
[openwrt/luci#867](https://github.com/openwrt/luci/issues/867)
Reviewed-by: Marty Plummer <hanetzer@startmail.com>
Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[commit author fix, subject fix, message text wrap]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The specific flash chip used (W25Q256FVEM) accepts 50MHz for read
requests and higher for others. 104MHz for fast reads. ramips seems to
be limited to 80MHz based on testing with higher values (no speedup).
Based on upstream commit: 97738374a310b9116f9c33832737e517226d3722
time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.96s to 7.01s
[test done with backported upstream v4.19 driver[1], for numbers on
stock 4.14 driver please take a look at `ramips: Increase GB-PC2 SPI
frequency to 80MHz` commit message]
1. https://github.com/openwrt/openwrt/pull/1578
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[expanded note about spi driver version]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The flash chip on the board (Spansion S25FL256SAIF00) is rated to
support at least 50MHz for normal read requests according to the
datasheet. 133MHz for fast reads. However, ramips seems to be limited to
80MHz.
>From testing this, higher values do not improve speeds.
time dd if=/dev/mtdblock3 of=/dev/null bs=64k from
42.82s to 14.09s.
boot speed is also faster:
[ 66.884087] procd: - init - vs
[ 48.976049] procd: - init -
Since spi speed was requested:
[ 3.538884] spi-mt7621 1e000b00.spi: sys_freq: 225000000
CPU is 900MHz:
[ 0.000000] CPU Clock: 900MHz
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[fixed commit message by adding missing 0 in the spi-mt7621 clock output]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7621
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 16MB (Macronix MX25L12835F)
WiFi: MediaTek MT7662E bgn 2SS
WiFi: MediaTek MT7662E nac 2SS
BTN: ON/OFF - Reset - WPS - AP/Extender toggle
LED: - Arrow Right (blue)
- Arrow Left (blue)
- WiFi 1 (red/green)
- WiFi 2 (red/green)
- Power (green/amber)
- WPS (Green)
UART: UART is present as Pads on the backside of the PCB. They are
located on the other side of the Ethernet port.
3.3V - GND - TX - RX / 57600-8N1
3.3V is the nearest one to the antenna connectors
Installation
------------
Update the factory image via the Netgear web-interfaces (by default:
192.168.1.250/24).
You can also use the factory image with the nmrpflash tool.
For more information see https://github.com/jclehner/nmrpflash
Signed-off-by: David Bauer <mail@david-bauer.net>
[merge conflict in 02_network, flash@0 node rename, wlan DTS triggers]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Device specification:
- SoC: RT5350F
- CPU Frequency: 360 MHz
- Flash Chip: Winbond 25Q32 (4096 KiB)
- RAM: 32768 KiB
- 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
- 1x external, non-detachable antenna
- UART (J1) header on PCB (57800 8n1)
- Wireless: SoC-intergated: 2.4GHz 802.11bgn
- USB: None
- 3x LED, 2x button
Flash instruction:
1. Configure PC with static IP 192.168.1.2/24 and start TFTP server.
2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin"
to "kstart_recovery.bin" and place it in TFTP server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
4. Router will download file from TFTP server, write it to flash and reboot.
Signed-off-by: Vladimir Kot <vova28rus@gmail.com>
[fixed git commit author and whitespace issues in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The WIZnet WizFi630S board is in the miniPCIe form factor.
SoC: Mediatek MT7688AN
RAM: 128MB
Flash: 32Mb
WiFi: 2.4GHz
Ethernet: 3x 100Mbit
USB: 1 (USB 2.0)
serial ports: 2 (1x full, 1xlite)
Flash and recovery instructions: Use the factory installed u-boot boot
loader. It is available on UART2 (115200,8,n,1). Then get the
sysupgrade image from a tftp server.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
[whitespace and device name in makefile fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This refreshes the current kernel configuration to remove unneeded
options, add some automatically added ones and reorders them. The normal
build did this automatically, so the builds already used this
configuration.
CONFIG_HW_RANDOM_OMAP is explicitly activated for the cortexa72
subtarget because it has an inside-secure,safexcel-eip76 IP core.
This was done with this command on the cortexa9 subtarget:
make kernel_oldconfig
and this one on the other subtargets:
make kernel_oldconfig CONFIG_TARGET=subtarget
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds a ChromiumOS 3.18 patch [0] that fixes memory
allocation issues under memory pressure by keeping track
of missed allocs and rectify the omission at a later date.
It also adds ethtool counters for memory allocation
failures accounting so this can be verified.
[0] <d4e1e4ce68>
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Some broken ISPs (e.g. Comcast) send DHCPv6 packets with hop limit=0.
This trips up the TTL=0 check in the PPE if enabled.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
COMFAST CF-E5/E7 is a outdoor 4G LTE AP with PoE support, based on
Qualcomm/Atheros QCA9531.
Short specification:
2x 10/100 Mbps Ethernet, with 24v PoE support
64 MB of RAM (DDR2)
16 MB of FLASH (SPI)
2T2R 2.4 GHz, 802.11b/g/n
built-in 1x 3 dBi antennas
output power (max): 80 mW (19 dBm)
Qucetel EC20 LTE MODULE(1x external detachable antenna)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
[commit subject fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit adds support for TP-Link TL-WR710N v1 router.
CPU: Atheros AR9331 400MHz
RAM: 32MB
FLASH: 8MiB
PORTS: 1 Port 100/10 LAN (connected to a switch), 1 Port 100/10 WAN
WiFi: Atheros AR9331 1x2:1 bgn
USB: ChipIdea HDRC USB2.0
LED: SYS
BTN: Reset
Sysupgrade from `ar71xx` works without glitches.
Network interfaces assigned for LAN and WAN ports are `eth1` and `eth0`
respectively, what's consistent with `ar71xx` target. Wireless radio
path is automatically upgraded from `platform/ar933x_wmac` to
`platform/ahb/18100000.wmac`.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
This adds support for the Chinese version of TL-WR941N v7.
It uses QCA9558+AR8236 while the international version
uses TP9343 instead.
Specification:
- SoC: Qualcomm Atheros QCA9558
- Flash: 4 MB
- RAM: 64 MB
- Ethernet: Atheros AR8236 with 5 FE ports
Flash instruction:
Upload the generated factory firmware on web interface.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This allows users to specify a shorter mib poll interval so that the
swconfig leds could behave normal with current get_port_stats()
implementation.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This applies to ar8216 and ar8236. QCA's newer U-boot will enable
the switch mdio master for FE switches which makes phy inaccessible
from CPU mdio. (e.g. on TP-Link TL-WR941N v7 Chinese version which
uses QCA9558+AR8236.) For these devices PHY probing is broken and
mdio device probing is a must. We also need to disable switch mdio
master in driver for later PHY initialization.
Do a soft reset during hw_init so that mdio master can be disabled
and expose PHYs to CPU mdio for later PHY accessing.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
ar8xxx_mib_capture will update mib counters for all ports. Current
code only update one port at a time and the data for other ports
are lost.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Partially reverts commit eff3549c58.
AR7240 and AR9341 have buggy hardware switch LED trigger. The AR7240
one doesn't blink and the blinking of port0/port5 is reversed on
AR9341 if we swap PHY0 and PHY4. (Only blinking is reversed, which
means LED for PHY0 will lit when PHY0 is link up and will blink when
PHY4 has active link and vice versa.) On these two chips a software
swconfig LED trigger is required.
This commit adds swconfig port stats back but:
1. move checking of mib_t/rxb_id into ar8xxx_chip since we can't
distinguish ar7240sw and ar8216 using only chip id.
2. don't update mib counter in get_port_stat. This function is called
every 0.01s and this capturing procedure will take up a lot of CPU.
We already have a mib_work_func updating mib counters every 2s so
return the saved counter instead of fetching new data. The blinking
rate will be weird but it should solve the previously mentioned CPU
time problem.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This builtin switch is a bugless ar8216 with different mib counters
and gigabit cpu port.
Atheros uses the same device ID and it's impossible to distinguish
the standalone one and the builtin one. So we add support to mdio
device probe only.
This switch doesn't have buggy vlan tag so it's not needed to enable
atheros header. This commit changed ar8216_setup_port so that it can
be reused for this switch.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Atheros FE switches have a builtin mdio master available for PHY
accessing and on ar724x/ar933x builtin switches this mdio master
is the only way of accessing PHYs.
After this patch if there is phy_read/phy_write method available
in ar8xxx_chip we register a separated mdio bus for accessing PHYs.
Still adds support for mdio device probing only since this isn't
needed for those switches registered using PHY probing.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
ar8229 is the builtin switch in ar934x and later chips. There is
also a standalone version available and their registers/functions
are the same.
This commit added support for the builtin ar8229. The only thing
missing for standalone ar8229 should be phy modes. Since I don't
have a router using that, this commit doesn't add support for
other phy modes.
Only add its support for mdio-device probing method because the
current PHY probing can't return 1G speed when it's a FE switch.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
ar8xxx_id_chip is used to determine current ar8xxx_chip using switch
id and this isn't needed during mdiodev probing.
Move it out of ar8xxx_probe_switch so that we can skip it.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
for mdio-device probing we still need to read chip id but ar8xxx_chip
can be determined using drvdata. We can't distinguish the buggy
standalone ar8216 and the builtin ar8216 in ar724x/ar933x using chip
id.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The following patches are dropped because they are merged upstream:
-0001-tty-serial-drop-QCA-pecific-SoC-symbols.patch
-0006-usb-drop-deprecated-symbols.patch
-0009-MIPS-ath79-add-lots-of-missing-registers.patch
-0010-MIPS-ath79-add-support-for-QCA953x-QCA956x-TP9343.patch
-0014-MIPS-ath79-finetune-cpu-overrides.patch
-0015-MIPS-ath79-enable-uart-during-early_prink.patch
-0016-MIPS-ath79-get-PCIe-controller-out-of-reset.patch
This patch is dropped due to the introduction of spi-mem framework:
-461-spi-ath79-add-fast-flash-read.patch
Thank to Michael Marley @mamarley for his work on this patch:
-910-unaligned_access_hacks.patch
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[synchronized kernel config with make kernel_oldconfig]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
linux 4.19 doesn't accept a NULL device for these functions.
It also complains that the device struct in net_device doesn't have
a dma_mask set.
Pass the device struct from platform_device for these functions.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Kernel newer than 4.15 dropped "data" field and used from_timer
to cast out the parent struct pointer for current timer.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The DIR-510L Wireless Router are based on the MT7620A SoC.
Specification:
-MediaTek MT7620A (580 Mhz)
-128 MB of RAM
-16 MB of FLASH
-802.11bgn radio
-1x 10/100 Mbps Ethernet
-2x internal, non-detachable antennas
-UART (J3) header on PCB (57600 8n1)
-1x bi-color LED (GPIO-controlled), 2x button
-JBOOT bootloader
Known issues:
-Ethernet port is used as LAN
-No communication with charger IC. (uart bitbang needed)
Installation:
Apply factory image via d-link http web-gui.
How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.binhttp://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed whitespace issue in 10-rt2x00-eeprom]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Some boards with JBOOT have partiton between bootloader
and kernel image. This patch add possibility to change kernel
partition start address.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
clk_get_rate returns the current clock rate in Hz for a clock source so
if we divide it by 1M, then we get frequency in MHz and not kHz.
Signed-off-by: Qin Wei <support@vocore.io>
[added missing commit message, and fixed author with SoB from PR message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The PCIe DWC host controller is now using MSI
(Message-signaled-interrupts) by default.
While ath9k itself does support MSI here, a lot of wlan adapters do not.
Avoid non-functioning cards by simply continue to disable MSI for now.
This can be done by appending "pci=nomsi" to the boot cmdline.
Also an extra fix needs to be backported which avoids MSI initialization
which prevented legacy IRQ's init from taking over.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The DWC host controller symbols are now depending on a few others
Fixes: ca1b93f038 ("imx6: add support for kernel 4.19")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware
almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation
AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi
indicators, the fifth LED is used as an ethernet link/activity indicator.
CPU: Atheros AR9342 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
WLAN: QCA988X
Ports: 1x GbE
Flashing procedure is identical to the NanoStation AC loco and can be performed
either via serial or the factory firmware upgrade.
Serial flashing:
1. Connect to serial header on device (8N1 115200)
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Flashing through factory firmware:
1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version.
2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot
Thanks to @cybermaus for testing!
Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com>
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
The Mikrotik RouterBOARD SXT 2nD r3 is an outdoor WiFi AP / CPE
with a single 2.4 GHz radio and a 100 Mbps Ethernet port.
The device similar to the SXT 2nD r2, but it has SPI NOR flash instead
of NAND flash.
Hardware
--------
CPU: Atheros AR9344 (600 MHz)
RAM: 64 MiB
FLASH: 16 MiB SPI NOR W25Q128
ETH: 1x 100 Mbps Atheros AG71xx
WiFi: 2T2R 802.11b/g/n (ath9k)
Power: Passive PoE 8-30 V
Installation instructions:
1. Boot openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf using a
DHCP+TFTP server.
2. Erase the "firmware" partition using the mtd command. This should
no longer be required once this patch is merged.
3. Use sysupgrade to install to flash. The file
openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin
should be used.
Signed-off-by: Xavier Douville <github@douville.org>
ath10k_pci driver crashes once loaded and causes boot loops on this
device as 5GHz radio QCA9880-AR1A shipped with this router is broken.
It's not possible to fix this problem in software, miniPCIe radio has to
be replaced.
We could've probably fixed crashing of the ath10k driver by reverting
following upstream commit:
commit 1a7fecb766c83dace747f42b25bbb544b00a0163
Author: Michal Kazior <michal.kazior@tieto.com>
Date: Sat Jan 24 12:14:48 2015 +0200
ath10k: reset chip before reading chip_id in probe
but it's not worth the effort as it wouldn't make that 5GHz radio usable
anyway. So it seems more convenient to just remove the crashing driver
and provide bootable images, as I believe, that a router that is working
but degraded is better than a router that will not work.
For details please see discussions in PR[1] and in FS#1743[2].
1. https://github.com/openwrt/openwrt/pull/1349
2. https://bugs.openwrt.org/index.php?do=details&task_id=1743
Signed-off-by: Aubrey McIntosh, PhD <aubrey.mcintosh@utexas.edu>
[subject and commit message tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The port labled as "LAN" is eth1.
That's different from the -lite variant,
where the only existing port eth0 is used as LAN
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
Reading and writing to and from flash storage is slowed down
enormously by some functions which use a block size of 1.
This patch reworks the extraction scripts to be much faster and
efficient by reading and writing in possibly one big block.
This is based on the initial commit a69e101 for ipq40xx by
Christian Lamparter <chunkeey@gmail.com>.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Rosen Penev <rosenp@gmail.com>
- Former "mir3g" board name becomes "xiaomi,mir3g".
- Reorder some entries to maintain alphabetical order.
- Change DTS so status LEDs (yellow/red/blue) mimic
Xiaomi stock firmware: (Section Indicator)
<http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf>
<http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf>
|Yellow: Update (LED flickering), the launch of the system (steady light);
|Blue: during normal operation (steady light);
|Red: Safe mode (display flicker), system failure (steady light);
Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
[Added link to similar Router 3 model]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware
--------
CPU: Qualcomm IPQ4018
RAM: 256M
FLASH: 32M SPI NOR W25Q256
ETH: QCA8075
WiFi2: IPQ4018 2T2R 2SS b/g/n
WiFi5: IPQ4018 2T2R 2SS n/ac
LED: - Power amber
- LAN1(PoE) green
- LAN2 green
- Wi-Fi 2.4GHz green
- Wi-Fi 5GHz green
BTN: - WPS
UART: 115200n8 3.3V J1
VCC(1) - GND(2) - TX(3) - RX(4)
Added basic support to get the device up and running for a sysupgrade
image only.
There is currently no way back to factory firmware, so this is a one-way
street to OpenWRT.
Install from factory condition is convoluted, and may brick your device:
1) Enable SSH and disable the CLI on the factory device from the web user
interface (Management->Advanced)
2) Reboot the device
3) Override the default, limited SSH shell:
a) Get into the ssh shell:
ssh admin@192.168.1.1 /bin/sh --login
b) Change the dropbear script to disable the limited shell. At the
empty command prompt type:
sed -i '/login_ssh/s/^/#/g’ dropbear
/etc/init.d/dropbear restart
exit
4) ssh in to a (now-) normal OpenWRT SSH session
5) Flash your built image
a) scp openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
admin@192.168.1.1:/tmp/
b) ssh admin@192.168.1.1
c) sysupgrade -n
/tmp/openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
6) After flash completes (it may say "Upgrade failed" followed by
"Upgrade completed") and device reboots, log in to newly flashed
system. Note you will now need to ssh as root rather than admin.
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
[whitespace fixes, reordered partitions, removed rng node from 4.14,
fixed 901-arm-boot-add-dts-files.patch]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Eric has reported on OpenWrt's bug tracking system[1], that he's not
able to use USB devices on his WNDR3400v2 device after the boot, until
he turns on GPIO #21 manually through sysfs.
1. https://bugs.openwrt.org/index.php?do=details&task_id=2170
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Andrey has reported on OpenWrt's bug tracking system[1], that he
currently can't use ar93xx_uart as pure serial UART without console
(CONFIG_SERIAL_8250_CONSOLE and CONFIG_SERIAL_AR933X_CONSOLE undefined),
because compilation ends with following error:
ar933x_uart.c: In function 'ar933x_uart_console_write':
ar933x_uart.c:550:14: error: 'struct uart_port' has no
member named 'sysrq'
1. https://bugs.openwrt.org/index.php?do=details&task_id=2152
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Building tda1997x fails now unless V4L2_FWNODE is selected:
drivers/media/i2c/tda1997x.o: in function `tda1997x_parse_dt'
undefined reference to `v4l2_fwnode_endpoint_parse'
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This patch increases available space from 20MB to 86MB.
Netgrear OEM firmware contains a 'netgear' partition followed 'ubi',
which can be used in openwrt for larger ubi space. (similar to
Netgear R7800).
original author (notmyrealhandle) tested this on R7500v2 and point that
OEM firmware can auto rebuild this partition (if used by openwrt).
Author: notmyrealhandle<22336358+notmyrealhandle@users.noreply.github.com>
Signed-off-by: Wang Xin-yu (王昕宇) <comicfans44@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [minor touch-ups]
Support for the Nanostation M (XW) was added in 40530c8eb with board
name "nanostation-m-xw". The current image for the "Nanostation M"
uses "nano-m" as the board name.
This commit renames it to the full product name as it's used by all
other boards. The legacy boardname of the ar71xx target is added
via SUPPORTED_DEVICES to ease switching to ath79 target.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[touch-ups on the commit message, removed subject remains]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
To be able to configure pwms the pwm driver needs to know the number off
cells in the "pwms" property. For this platform this is 2.
Signed-off-by: Micke Prag <micke.prag@telldus.se>
jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board.
Specification
SoC: Atheros AR7161
RAM: 64 MB DDR
Flash: 16 MB SPI NOR
Ethernet: 2x 10/100/1000 Mbps AR8316
LAN (CN11), WAN/PoE (CN6 - close to power barrel
connector, 48 V)
MiniPCI: 2x
LEDS: 4x, which 3 are GPIO controlled
Buttons: 2x GPIO controlled
Reset (SW1, closer to ethernet ports), WPS (SW2)
Serial: 1x (only RX and TX are wired)
baud: 115200, parity: none, flow control: none
Currently there is one caveat compared to ar71xx target images as the
MAC addresses are random on every reboot. To remedy this one needs to
store the WAN MAC address in RedBoot configuration. OpenWrt on first
boot, after flashing, will read out the address and assign proper ones
to both WAN and LAN ports. It is iportant to NOT keep the old
configuration when doing sysupgrade from ar71xx.
Upgrading from OpenWrt ar71xx image
1. Connect to serial port,
2. Download OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade -n <openwrt_sysupgrade_image_name>
3. After writing new image OpenWrt will reboot, now interrupt boot
process and enter RedBoot (bootloader) command line by pressing
Ctrl+C,
4. Enter following commands (replace variable accordingly),
set_mac (to view MAC addresses)
alias ethaddr <wan_port_mac_adress>
(confirm storing the value by inputting y and pressing Enter)
reset
5. Now board should restart and boot OpenWrt with proper MAC addresses.
Installation
1. Prepare TFTP server with OpenWrt initramfs image,
2. Connect to WAN ethernet port,
3. Connect to serial port,
4. Power on the board and enter RedBoot (bootloader) command line by
pressing Ctrl+C,
5. Enter following commands (replace variables accordingly):
set_mac (to view MAC addresses)
alias ethaddr <wan_port_mac_address>
(confirm storing the value by inputting y and pressing Enter)
ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress>
load -r -b 0x80060000 <openwrt_initramfs_image_name>
exec -c ""
6. Now board should boot OpenWrt initramfs image,
7. Download OpenWrt sysupgrade image to /tmp directory and flash it
with:
sysupgrade <openwrt_sysupgrade_image_name>
8. Wait few minutes, after the D2 LED will stop blinking, the board
is ready for configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
In PR [1] introducing initial support for Ubiquiti RouterStation boards,
Mathias Kresin suggested to replace the combined sysupgrade image with
tarball generated by sysupgrade-tar.sh. This would simplify deployment
of sysupgrade as the kernel size (needed to update FIS partition) could
be simply calculated on the fly instead of reading value from combined
image header. Unfortunately this would break sysupgrade compatibility
between ar71xx image and ath79 image. Therefore this commit creates
migration path to use new sysuprade image, it adds code to accept both
of them at this moment. The plan is to keep it until new stable version
is released. Then the image recipe should be changed to new format and
compatibility code for old image removed.
1. https://github.com/openwrt/openwrt/pull/1237
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
When upgrading from ar71xx target images to ath79 based ones, the
integrated wireless interface changes its sysfs path. Therefore the
previous enabled wireless interface will be disabled, which can cause
false complains about it not working. This commit adds hotplug event
which migrates to new path and will keep the wrireless interface
enabled after upgrade.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Align the LEDs deffinition with MACH file present in ar71xx target which
has the correct LED functions and colors adescription.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
It is unused by default and upstream is trying to remove it as it has
negative effects when the driver is under load. Upstream explanation:
netpoll: avoid capture effects for NAPI drivers
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC).
This capture, showing one ksoftirqd eating all cycles
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
It seems that all networking drivers that do use NAPI
for their TX completions, should not provide a ndo_poll_controller() :
Most NAPI drivers have netpoll support already handled
in core networking stack, since netpoll_poll_dev(
uses poll_napi(dev) to iterate through registered
NAPI contexts for a device.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Although the amount of data read here is smaller than for the
caldata, there still might be some speed gain compared to reading
bytewise. And there is no harm ...
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reading and writing to and from flash storage is slowed down
enormously by some functions which use a block size of 1.
This patch reworks the extraction scripts to be much faster and
efficient by reading and writing in possibly one big block.
This is based on the initial commit a69e101 for ipq40xx by
Christian Lamparter <chunkeey@gmail.com>.
Speed comparison @ TP-Link TL-WDR4300 (just manually) results
in a time reduction by three orders of magnitude (99.9 %).
> time dd if=/dev/mtd3 of=/lib/firmware/test-slow bs=1 count=4096 skip=4096
4096+0 records in
4096+0 records out
real 0m 15.85s
user 0m 0.06s
sys 0m 13.28s
> time dd if=/dev/mtd3 of=/lib/firmware/test-fast bs=4096 count=1 skip=4096 iflag=skip_bytes
1+0 records in
1+0 records out
real 0m 0.02s
user 0m 0.00s
sys 0m 0.02s
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reading and writing to and from flash storage is slowed down
enormously by some functions which use a block size of 1.
This patch reworks the extraction scripts to be much faster and
efficient by reading and writing in possibly one big block.
This is based on the initial commit a69e101 for ipq40xx by
Christian Lamparter <chunkeey@gmail.com>.
Speed comparison @ UBNT AC-Mesh (just manually) results
in a time reduction by three orders of magnitude (99.9 %).
> time dd if=/dev/mtd6 of=/lib/firmware/test-slow bs=1 count=4096 skip=4096
4096+0 records in
4096+0 records out
real 0m 16.84s
user 0m 0.07s
sys 0m 13.54s
> time dd if=/dev/mtd6 of=/lib/firmware/test-fast bs=4096 count=1 skip=4096 iflag=skip_bytes
1+0 records in
1+0 records out
real 0m 0.02s
user 0m 0.00s
sys 0m 0.02s
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Rosen Penev <rosenp@gmail.com>
We currently generate a kernel that boots from the harddrive
in the DIR-685. That's not how we usually do things, so
let's augment it to boot from flash and mount the rootfs
using squashfs and JFFS2 like everyone else.
Partition splitting only work when the partitions are
inside of a "partitions" node which is why we have a patch
like this (submitted upstream).
Another patch drops the rootfs arguments and renames the
firmware partition while adding the compatible "wrg"
to it so the WRGG parser will kick in.
Factory image was tested by bravely reflashing the DIR-685
from stock firmware using the web UI and the serial console
boot loader.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WRGG images exist in both big and little endian variants,
as can be seen from the image generator in
tools/firmware-utils/src/mkwrggimg.c, you either pass
the "-b" flag or not. The D-Link DIR-685 is using little
endian images so we need to support splitting these.
Detect endianness like this: if the kernel entity size
gets silly big (bigger than the flash memory) we are
probably using the wrong endianness.
Example: my kernel of 0x0067ff64 was switched around by
wrong endianness and detected as 0x64ff67a0 (the actual
size in swapped endianness + header 0xa0).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band
wireless router.
Specification
SoC: Qualcomm Atheros QCA9558
RAM: 256 MB DDR2
Flash: 16 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet: 5x 10/100/1000 Mbps QCA8337N
USB: 1x 2.0
LEDS: 4x GPIO controlled
Buttons: 2x GPIO controlled
UART: 4 pin header, starting count from white triangle on PCB
1. VCC 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Tools > Firmware,
4. Select OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
is ready for configuration.
Alternative installation
1. Prepare TFTP server with OpenWrt sysupgrade image,
2. Connect to one of LAN (yellow) ethernet ports,
3. Connect to UART port (leaving out VCC pin!),
4. Power on router,
5. When asked to enter a number 1 or 3 hit 2, this will select flashing
image from TFTP server option,
6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8),
then router ip (default is 192.168.99.9) and for last, image name
downloaded from TFTP server (default is uImageESR1200_1750),
7. After providing all information U-Boot will start flashing the image,
You can observe progress on console, it'll take few minutes and when
the Power LED will stop blinking, router is ready for configuration.
Additional information
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: aigo3d0a0tdagr
useful for creating backup of original firmware.
When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep
the old configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M (NANYA NT5CC128M16JR-EK)
FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI)
ETH: Qualcomm QCA8072
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
WiFi5: QCA9984 4T4R 4SS n/ac
LED: - Connect green/blue/red
- Power green
BTN: WPS/Connect
UART: 115200n8 3.3V
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz3000'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ3000.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz3000.bin uboot0
> mtd write /path/to/uboot-fritz3000.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
