The ZTE MF287 requires a different board calibration file for ath10k than
the ZTE MF287+. The two devices receive their own DTS, thus the device tree
is slightly refactored.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Changelog from quic:
Bug fixes, stability improvements from previous releases
are present. There are no backward comatibility issues
with this release.
Known issues:
IPV6 connectivity problem, see: https://github.com/openwrt/openwrt/pull/13203#issuecomment-1666947749
Tested-by: Michał Kwiatek <michal@kwiatek.it> # Xiaomi AX3600
Signed-off-by: Michał Kwiatek <michal@kwiatek.it>
Changes:
9dc0800 wireless-regdb: Update regulatory rules for Philippines (PH)
111ba89 wireless-regdb: Update regulatory rules for Egypt (EG) from March 2022 guidelines
ae1421f wireless-regdb: Update regulatory info for Türkiye (TR)
20e5b73 wireless-regdb: Update regulatory rules for Australia (AU) for June 2023
991b1ef wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports.
The majority of the code is based on @jewwest's PR #11830.
Specifications:
* CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2)
* Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA)
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000 Mbps WAN (Qualcomm QCA8075),
1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY)
* Wi-Fi:
* 2.4 GHz: Qualcomm QCN5024 4x4
* 2x 5 GHz: Qualcomm QCN5054 4x4
* USB: 2x USB 3.0
* LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN
* Keys: LEDs On/Off, Power, Reset, RFKILL, WPS
* UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8
* Power: 19 VDC, 3.1 A
Installation:
* Flashing OpenWrt is done in two steps:
a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-).
This writes an initramfs based OpenWrt image onto the RAX120v2
b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline
* U-Boot allows booting an initramfs image via TFTP:
- Set ip of your PC to 192.168.1.100
- At the serial console interrupt boot at "Hit any key to stop autoboot:"
- In u-boot run `tftpsrv`
- On your PC send the OpenWrt initramfs image:
tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb
Make 5G Aquantia phy work:
For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in
u-boot by writing the firmware to the correct mtd partition.
The firmware file found in the Netgear stock firmware under /lib/firmware/ named
'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to
be converted to a MBN file.
The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source,
under 'git_home/u-boot.git/tools/mkheader.py'
Convert the CLD file to MBN using:
$ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn
This MBN file can then be flashed to the MTD partition to be used by u-boot.
The necessary files can also be found in
https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware
* Write MBN file to MTD partition to be loaded automatically by u-boot:
U-boot automatically tries to load the firmware from nand at address 0x7e00000 which
corresponds to `/dev/mtd25` in OpenWrt.
- find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25)
$ fgrep -i 'ethphyfw' /proc/mtd
mtd25: 00080000 00020000 "ethphyfw
- copy mbn file to /tmp/ folder of the router
$ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/
- write mbn file to ethphyfw partition
$ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to RAX120v2 GPL source:
https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
This updates the Intel iwlwifi firmware for AX200 and AX210 from version
66 to version 72. Version 72 is the latest version supported by iwlwifi
from kernel 6.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Changelog from quic:
Bug fixes, stability improvements from previous releases
are present. There are no backward comatibility issues
with this release.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Michał Kwiatek <michal@kwiatek.it> # Xiaomi AX3600
Signed-off-by: Michał Kwiatek <michal@kwiatek.it>
Changelog from quic:
Bug fixes, stability improvements from previous releases
are present. There are no backward comatibility issues
with this release.
Tested-by: Michał Kwiatek <michal@kwiatek.it> # Xiaomi AX3600
Signed-off-by: Michał Kwiatek <michal@kwiatek.it>
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The upstream board-2.bin file in the linux-firmware.git
repository for the QCA4019 contains a packed board-2.bin
for this device for both 2.4G and 5G wifis. This isn't
something that the ath10k driver supports.
Until this feature either gets implemented - which is
very unlikely -, or the upstream boardfile is mended
(both, the original submitter and ath10k-firmware
custodian have been notified). OpenWrt will go back
and use its own bespoke boardfile. This unfortunately
means that 2.4G and on some revisions the 5G WiFi is
not available in the initramfs image for this device.
Fixes: #12886
Reported-by: Christian Heuff <christian@heuff.at>
Debugged-by: Georgios Kourachanis <geo.kourachanis@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
When using an Intel AX210 card, the Bluetooth hci interface failed
to start due to a missing "ibt-0041-0041.sfi" file.
Bluetooth: hci0: Failed to load Intel firmware file intel/ibt-0041-0041.sfi (-2)
A device specific configuration file (DDC) is also required:
Bluetooth: hci0: Found device firmware: intel/ibt-0041-0041.sfi
Bluetooth: hci0: Waiting for firmware download to complete
...
Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-0041-0041.ddc
Bluetooth: hci0: Applying Intel DDC parameters completed
Bluetooth: hci0: Firmware timestamp 2023.13 buildtype 1 build 62562
Fixes: #8558
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The ZTE MF287+ is a LTE router used (exclusively?) by the network operator
"3". The MF287 (i.e. non-plus aka 3Neo) is also supported (the only
difference is the LTE modem)
Specifications
==============
SoC: IPQ4018
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 4x GBit LAN
LTE: ZTE Cat12 (MF287+) / ZTE Cat6 (MF287)
WiFi: 802.11a/b/g/n/ac SoC-integrated
MAC addresses
=============
LAN: from config + 2
WiFi 1: from config
WiFi 2: from config + 1
Installation
============
Option 1 - TFTP
---------------
TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:
setenv serverip 192.168.1.100
setenv ipaddr 192.168.1.1
tftpboot 0x82000000 openwrt.bin
bootm 0x82000000
From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:
ubiattach -m14
cat /dev/ubi0_0 > /tmp/ubi0_0
cat /dev/ubi0_1 > /tmp/ubi0_1
Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.
Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:
ubirmvol /dev/ubi0 -N ubi_rootfs
ubirmvol /dev/ubi0 -N kernel
Option 2 - From stock firmware
------------------------------
The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.
The exploit will be available at the device wiki page.
Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".
ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd13 is the partition labelled "rootfs" by calling
"cat /proc/mtd".
Complete commands:
cd /tmp
tftp -g -r factory.bin 192.168.0.22
cat /proc/driver/sensor_id
flash_erase /dev/mtd13 0 0
dd if=/tmp/factory.bin of=/dev/mtdblock13 bs=131072
Afterwards, reboot your device and you should have a working OpenWrt
installation.
Restore Stock
=============
Option 1 - via UART
-------------------
Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.
Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.
ubiattach -m 14
ubirmvol /dev/ubi0 -N kernel
ubirmvol /dev/ubi0 -N rootfs
ubirmvol /dev/ubi0 -N rootfs_data
ubimkvol /dev/ubi0 -N kernel -s $kernel_length
ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1
Option 2 - from within OpenWrt
------------------------------
This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.
Follow the commands from Option 1 to flash back to stock.
LTE Modem
=========
The LTE modem is similar to other ZTE devices and controls some more LEDs
and battery management.
Configuring the connection using uqmi works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Currently, ipq807x only covers Qualcomm IPQ807x SoC-s.
However, Qualcomm also has IPQ60xx and IPQ50xx SoC-s under the AX WiSoC-s
and they share a lot of stuff with IPQ807x, especially IPQ60xx so to avoid
duplicating kernel patches and everything lets make a common target with
per SoC subtargets.
Start doing that by renaming ipq807x to qualcommax so that dependencies
on ipq807x target can be updated.
Signed-off-by: Robert Marko <robimarko@gmail.com>
source.codeaurora.org project has been shut down and the nxp
repositories has been moved to github. Update the repository
link to the new location.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Contains following updates:
* ipq8074: update RegDB in new submitted BDF
* Revert "ipq8074: update RegDB in new submitted BDF"
* qcn9074: update RegDB in new submitted BDF
* ipq8074: update RegDB in new submitted BDF
* qca-wireless: ipq40xx: add BDFs for ZTE MF287+
* Add BDFs for prpl Foundation Haze board
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 5d2de00555.
I received multiple reports that in various configurations this FW version
is not stable and crashes, so lets revert to 01385 revision which works.
Fixes#12815
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [fixes tag]
QCA released a point update for the 2.9.0.1 firmware, so lets update to it.
Runtime tested on Dynalink DL-WRX36.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
The default location of ppfe-firmware has been changed
from codeuaurora to github. Also use the latest tag for
Layerscape Linux Development POC from NXP.
Tested on:
* NXP FRWY-LS1012A
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of fman-ucode has been changed from
codeuaurora to github. Also use the latest tag for Layerscape
Linux Development POC from NXP.
Tested on:
* NXP LS1046A-RDB
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of ls-rcw has been changed from codeuaurora
to github. The reason is that the old codeaurora source no longer
resolves. Also use the latest tag for Layerscape Linux Development
POC from NXP.
Tested on:
* NXP FRWY-LS1012A
* NXP LS1046A-RDB
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE, Mention that previous codeaurora source is
no longer available)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The BDFs for the:
Aruba AP-365
Devolo Magic 2 WiFi next
Edgecore ECW5410
Edgecore OAP100
Extreme Networks WS-AP3915i
GL.iNet GL-A1300
GL.iNet GL-AP1300
GL.iNet GL-S1300
Linksys EA8300
Linksys WHW03v2
Nokia Wi4A AC400i
P&W R619AC
Pakedge WR-1
Qxwlan E2600AC C1
Sony NCP-HG100/Cellular
Teltonika RUTX10
ZTE MF18A
were upstreamed to the ath10k-firmware repository
and landed in linux-firmware.git.
Furthermore the BDFs for the:
8devices Habanero
8devices Jalapeno
Qxwlan E2600AC C2
have been updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Based on Paul Fertser <fercerpav@gmail.com>'s guidance:
Change AUTORELEASE in rules.mk to:
```
AUTORELEASE = $(if $(DUMP),0,$(shell sed -i "s/\$$(AUTORELEASE)/$(call commitcount,1)/" $(CURDIR)/Makefile))
```
then update all affected packages by:
```
for i in $(git grep -l PKG_RELEASE:=.*AUTORELEASE | sed 's^.*/\([^/]*\)/Makefile^\1^';);
do
make package/$i/clean
done
```
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The firmware file for mt7601u (MediaTek MT7601U Wireless MACs) has
been moved to the mediatek/ folder by commit
8451c2b1 mt76xx: Move the old Mediatek WiFi firmware to mediatek
Address this by updating the location of the firmware file in our
linux-firmware Makefile generating the mt7601u-firmware package.
All other MediaTek Wi-Fi firmware files are supplied by OpenWrt's
own repository rather than being taken from linux-firmware.
Fixes: d53fe5d9ce ("linux-firmware: update to 20230515")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Changes:
43f81b4 wireless-regdb: update regulatory database based on preceding changes
66f245d wireless-regdb: Update regulatory rules for Hong Kong (HK)
e78c450 wireless-regdb: update regulatory rules for India (IN)
1647bb6 wireless-regdb: Update regulatory rules for Russia (RU). Remove DFS requirement.
c076f21 Update regulatory info for Russia (RU) on 6GHz
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
This adds a new package with Broadcom SPROMs that can be used as fallback when
the devices lack physical SPROMs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Current WLAN.HK.2.5.0.1 FW is quite old and buggy, but we had to hold off
from updating to 2.6.0.1 and 2.7.0.1 as they had compatibility regressions,
but now QCA finally released 2.9.0.1 FW which is working on all of the
boards.
So finally update IPQ8074 and QCN9074 FW to the latest
WLAN.HK.2.9.0.1-01385-QCAHKSWPL_SILICONZ-1 firmware.
In order to do so, we have to switch to using QCA-s QUIC repo instead of
Kalle-s.
QCA-s QUIC repo does not have BDF-s so we have to get the QCN9074 BDF from
Kalles repo.
Tested-by: Mireia Fernández Casals <meirin.f@gmail.com> # Xiaomi AX3600
Tested-by: Francisco G Luna <frangonlun@gmail.com> #Netgear WAX218
Signed-off-by: Robert Marko <robimarko@gmail.com>
ccd7e46 ipq40xx: add support for Wallystech DR40x9
2ce60e1 Revert "ipq40xx: add support for Wallystech DR40x9"
ea962ca ipq40xx: add Emplus WAP551 BDF
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Adds support for the Wallys DR40x9 series boards.
They come in IPQ4019 and IPQ4029 versions.
IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures.
Specifications are:
* CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz
* RAM: 512 MB
* Storage: 2MB of SPI-NOR, 128 MB of parallel NAND
* USB 3.0 TypeA port for users
* MiniPCI-E with PCI-E 2.0 link
* MiniPCI-E for LTE modems with only USB2.0 link
* 2 SIM card slots that are selected via GPIO11
* MicroSD card slot
* Ethernet: 2x GBe with 24~48V passive POE
* SFP port (Does not work, I2C and GPIO's not connected on hardware)
* DC Jack
* UART header
* WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac
* 4x MMCX connectors for WLAN
* Reset button
* 8x LED-s
Installation instructions:
Connect to UART, pins are like this:
-> 3.3V | TX | RX | GND
Settings are 115200 8n1
Boot initramfs from TFTP:
tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb
bootm
Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name>
The board file binary was provided from Wallystech on March 14th 2023
including full permission to use and distribute.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Netgear WAX218 is a 802.11ax AP claiming AX3600 support. It is wall
or ceiling mountable. It can be powered via PoE, or a 12 V adapter.
The board has footprints for 2.54mm UART headers. They're difficult to
solder because the GND is connected to a large copper plane. Only try
soldering if you are very skilled. Otherwise, use pogo pins.
Specifications:
---------------
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 366 MB of RAM available to OS, not sure of total amount
* Storage: Macronix MX30UF2G18AC 256MB NAND
* Ethernet:
* 2.5G RJ45 port (QCA8081) with PoE input
* WLAN:
* 2.4GHz/5GHz with 8 antennas
* LEDs:
* Power (Amber)
* LAN (Blue)
* 2G WLAN (Blue)
* 5G WLAN (Blue)
* Buttons:
* 1x Factory reset
* Power: 12V DC Jack
* UART: Two 4-pin unpopulated headers near the LEDs
* "J2 UART" is the CPU UART, 3.3 V level
Installation:
=============
Web UI method
-------------
Flashing OpenWRT using the vendor's Web UI is problematic on this
device. The u-boot mechanism for communicating the active rootfs is
antiquated and unreliable. Instead of setting the kernel commandline,
it relies on patching the DTS partitions of the nand node. The way
partitions are patched is incompatible with newer kernels.
Newer kernels use the SMEM partition table, which puts "rootfs" on
mtd12. The vendor's Web UI will flash to either mtd12 or mtd14. One
reliable way to boot from mtd14 and avoid boot loops is to use an
initramfs image.
1. In the factory web UI, navigate to System Manager -> Firmware.
2. In the "Local Firmware Upgrade" section, click Browse
3. Navigate and select the 'web-ui-factory.fit' image
4. Click "Upload"
5. On the following page, click on "Proceed"
The flash proceeds at this point and the system will reboot
automatically to OpenWRT.
6. Flash the 'nand-sysupgrade.bin' using Luci or the commandline
SSH method
----------
Enable SSH using the CLI or Web UI. The root account is locked out to
ssh, and the admin account defaults to Netgear's CLI application.
So we need to get creative:
First, make sure the device boots from the second firmware partition:
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/fw_setenv active_fw 1
Then reboot the device, and run the update:
scp -O -o kexalgorithms=diffie-hellman-group14-sha1 \
-o hostkeyalgorithms=ssh-rsa \
netgear_wax218-squashfs-nand-factory.ubi \
admin@<ipaddr>:/tmp/openwrt.ubi
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/ubiformat /dev/mtd12 -f /tmp/openwrt.ubi
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/fw_setenv active_fw 0
Now reboot the device, and it should boot into a ready-to-use OpenWRT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Francisco G Luna <frangonlun@gmail.com>
31ff96d ipq806x: add support for Nokia Airscale AC400i
1af1df2 ath11k: ipq8074: add Netgear WAX218
Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
Hardware
--------
SoC: Qualcomm IPQ8065
RAM: 512 MB DDR3
Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB)
4 MB SPI-NOR (Macronix MX25U3235F)
WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz
Qualcomm Atheros QCA9984 - 5Ghz
ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt)
eth1 - (1000Mbps in both)
Auto-negotiation broken on both.
USB: USB 2.0
LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red)
BTN: Reset
Other: SD card slot (non-functional)
Serial: 115200bps, near the Ethernet transformers, labeled 9X.
Connections from the arrow to the 9X text:
[NC] - [TXD] - [GND] - [RXD] - [NC]
Installation
------------
0. Connect to the device
Plug your computer into LAN2 (1000Mbps connection required).
If you use the LAN1/POE port, set your computer to force a 100Mbps link.
Connect to the device via TTL (Serial) 115200n8.
Locate the header (or solder pads) labeled 9X,
near the Ethernet jacks/transformers.
There should be an arrow on the other side of the header marking.
The connections should go like this:
(from the arrow to the 9X text): NC - TXD - GND - RXD - NC
1. Prepare for installation
While the AP is powering up, interrupt the startup process.
MAKE SURE TO CHECK YOUR CURRENT PARTITION!
If you see: "Current Partition is : partB" or
"Need to switch partition from partA to partB",
you have to force the device into partA mode, before continuing.
This can be done by changing the PKRstCnt to 5 and resetting the device.
setenv PKRstCnt 5
saveenv
reset
After you interrupt the startup process again,
you should see: Need to switch partition from partB to partA
You can now continue to the next step.
If you see: "Current Partition is : partA",
you can continue to the next step.
2. Prevent partition switching.
To prevent the device from switching partitions,
we are going to modify the startup command.
set bootcmd "setenv PKRstCnt 0; saveenv; bootipq"
setenv
3. First boot
Now, we have to boot the OpenWrt intifs.
The easiest way to do this is by using Tiny PXE.
You can also use the normal U-Boot tftp method.
Run "bootp" this will get an IP from the DHCP server
and possibly the firmware image.
If it doesn't download the firmware image, run "tftpboot".
Now run "bootm" to run the image.
You might see:
"ERROR: new format image overwritten - must RESET the board to recover"
this means that the image you are trying to load is too big.
Use a smaller image for the initial boot.
4. Install OpenWrt from initfs
Once you are booted into OpenWrt,
transfer the OpenWrt upgrade image and
use sysupgrade to install OpenWrt to the device.
Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
Source BDF files out of project dedicated repository and drop local file
from openwrt main repository.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Changes:
7f7a9f7 wireless-regdb: update regulatory database based on preceding changes
660a1ae wireless-regdb: Update regulatory info for Russia (RU) on 5GHz
fe05cc9 wireless-regdb: Update regulatory rules for Japan (JP) on 6GHz
d8584dc wireless-regdb: Update regulatory rules for Japan (JP) on 5GHz
c04fd9b wireless-regdb: update regulatory rules for Switzerland (CH)
f29772a wireless-regdb: Update regulatory rules for Brazil (BR)
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
ZyXEL NBG7815 is a premium 802.11ax "tri"-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 1 GB 2x Nanya NT5CC256M16ER-EK
* Storage:
* 8MB serial flash Winbond W25Q64DW
* 4GB eMMC flash Kingston EMMC04G-M627
* Ethernet:
* 4x1G RJ45 ports (QCA8074A) with 1x status LED per port
* 1x2.5G RJ45 port (QCA8081) with 1x status LED
* 1x10G RJ45 port (AQR113C) with 1x status LED
* Switch: Qualcomm Atheros QCA8075
* WLAN:
* 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate
* 2x 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
* Bluetooth CSR8811 using HSUART, currently unsupported
* USB: 1x USB3.0 Type-A port
* LED-s currently not supported:
* White
* Dark Blu
* Amber
* Purple
* Purple and dark blue
* Red
* Buttons:
* 1x Soft reset
* Power: 12V DC Jack
Installation instructions:
* Disconnect WAN
* Reset device to factory defaults by pushing reset button 15 sec,
LEDs should lit orange color.
* After 5-10 minutes, when the LEDs turn constant dark blue,
put your LAN cable and connect at address 192.168.123.1 by telnet on port 23
* Login with
NBG7815 login: root
password: nbg7815@2019
* cd /tmp/ApplicationData
* wget -O openwrt-ipq807x-generic-zyxel_nbg7815-squashfs-sysupgrade.bin http://...
* wget https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh
* run flash_to_openwrt.sh
If you can't use wget, you can transfer the files via nc.
See https://openwrt.org/inbox/toh/zyxel/nbg7815_armor_g5 for installation details.
Bluetooth usage:
* you need at least package bluez-utils, recommended bluez-daemon
* run following commands to enable and start
hciattach /dev/ttyMSM1 bcsp
hciconfig hci0 up
Many thanks to itorK for his work on this device:
https://github.com/itorK/openwrt/tree/nbg7815
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: André Valentin <avalentin@marcant.net>
Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports.
Specifications:
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 1024MB of DDR3
• Storage: 256MB Nand
• Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
• WLAN:
2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate
5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
• 1x USB 3.0
• 1 gpio-controlled dual color led (blue/red)
• Buttons: 1x soft reset / 1x WPS
• Power: 12V DC jack
A poulated serial header is onboard (J1004)
the connector size is a 4-pin 2.0 mm JST PH.
RX/TX is working, u-boot bootwait is active, secure boot is enabled.
Notes:
- Serial is completely deactivated in the stock firmware image.
- This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
- Installation can be done by serial connection or
SSH access on OEM firmware
Installation Instructions:
Most part of the installation is performed from an initramfs image
running OpenWrt, and there are two options to boot it.
Boot initramfs option 1: Using serial connection (3.3V)
1. Stop auto boot to get to U-boot shell
2. Transfer initramfs image to device
(openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb)
Tested using TFTP and a FAT-formatted USB flash drive.
3. Boot the initramfs image
# bootm
Boot initramfs option 2: From SSH access on OEM firmware
1. Copy the initramfs image to a FAT-formatted flash drive
(tested on single-partition drive) and connect it to device USB port.
2. Change boot command so it loads the initramfs image on next boot
Fallback to OEM firmware is provided.
# fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq'
3. Reboot the device to boot the initramfs
# reboot
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Check MTD partition table.
rootfs and rootfs_1 should be mtd18 and mtd20
depending on current OEM slot.
# cat /proc/mtd
4. Do a ubiformat to both rootfs partitions:
# ubiformat /dev/mtd18 -y -f /path_to/factory_image
# ubiformat /dev/mtd20 -y -f /path_to/factory_image
5. Set U-boot env variable: mtdids
# fw_setenv mtdids 'nand0=nand0'
6. Get offset of mtd18 to determine current OEM slot
- If current OEM slot is 1, offset is 16777216 (0x1000000)
- If current OEM slot is 2, offset is 127926272 (0x7a00000)
# cat /sys/class/mtd/mtd18/offset
7. Set U-boot env variable: mtdparts
If current OEM slot is 1, run:
# fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)'
If current OEM slot is 2, run:
# fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)'
8. Set U-boot env variable: bootcmd
# fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0'
9. Reboot the device
# reboot
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
The Edgecore EAP102 is a wall/ceiling mountable AP. The AP can be
powered by either PoE or AC adapter.
Device info:
- IPQ8071-A SoC
- 1GiB RAM
- 256MiB NAND flash
- 32MiB SPI NOR
- 2 Ethernet ports
- 1 Console port
- 2GHz/5GHz AX WLAN
- 2 USB 2.0 ports
Install instructions:
Prerequistes - TFTP server, preferrably within 192.168.1.0/24
Console cable plugged in (115200 8N1 no flow control)
1. Power on device and interrupt u-boot to obtain u-boot CLI
2. set serverip to IP address of the TFTP server:
`setenv serverip 192.168.1.250`
3. Download image from TFTP server:
`tftpboot 0x44000000 openwrt-ipq807x-generic-edgecore_eap102-squashfs-nand-factory.ubi`
4. Flash ubi image to both partitions and reset:
`sf probe
imxtract 0x44000000 ubi
nand device 0
nand erase 0x0 0x3400000
nand erase 0x3c00000 0x3400000
nand write $fileaddr 0x0 $filesize
nand write $fileaddr 0x3c00000 $filesize
reset`
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet:
* 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* 1x2.5G RJ45 port (QCA8081) with 1x status LED
* WLAN:
* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
* 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate
* 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate
* 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate
* USB: 1x USB3.0 Type-A port
* LED-s:
* System (Blue and Yellow)
* Network (Blue and Yellow)
* RGB light bar on top in X shape
* Buttons:
* 1x Power switch
* 1x Soft reset
* 1x Mesh button
* Power: 12V DC Jack
Installation instructions:
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd21 and mtd22 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
6. Reboot the device by:
reboot
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: Robert Marko <robimarko@gmail.com>
QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports.
Specifications:
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 1024MB of DDR3
• Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR
(contains art and u-boot-env)
• Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C)
• WLAN:
2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate
5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate
• LEDs:
7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs
• Buttons: 1x soft reset / 1x WPS
• Power: 12V DC jack
A poulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, hold WPS button til the second beep
(yes the router has a buzzer)
SSH is available on port 22200, login with user admin and
password "mac address of the router".
Installation Instructions:
• obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial)
• stop auto boot
• setenv serverip 192.168.10.1
• setenv ipaddr 192.168.10.10
• tftpboot the initramfs image
(openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb)
• bootm
• make sure that current_entry is set to "0":
"fw_printenv -n current_entry" should be print "0". If not,
do "fw_setenv current_entry 0"
• copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
to the device to /tmp folder
• sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4)
• reboot
Note: this leaves the second kernel / rootfs parition untouched. So if you want
to go back to stock, stop u-boot autoboot, "setenv current_entry 1" ,
"saveenv", "bootipq".
Stock firmware should start from the second partition.
Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt
in the first partitions
Make 10G Aquantia phy's work:
The aquantia phy's need a firmware to work. This can either be loaded
in linux with a userspace tool or in u-boot.
I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is
aq_load_fw available in u-boot. But first the right firmware needs to write
to the 0:ETHPHYFW mtd partition (it is empty on my device)
Grab the ethphy firmware image from:
https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn
and scp that to openwrt.
Check the 0:ETHPHYFW partition number:
cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10.
Backup the 0:ETHPHYFW partition:
dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place.
Write the new firmware image to the 0:ETHPHYFW partition:
"mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10".
Reboot to u-boot.
Check if aq_load_fw is working:
"aq_load_fw 0", that checks the firmware and if successfull,
loads iram and dram to one of the aquantia phy's.
If that worked, add the aq_load_fw to the bootcmd:
setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq"
"saveenv"
"reset"
Board reboots and the firmware load to both phy's should start and
then openwrt boots.
Check if the 10G ports work.
Note: lan port labeled "10G-2" is configured as WAN port as per default.
All other port are in the br-lan. This can be changed in the network config.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Edimax CAX1800 is a 802.11 ax dual-band AP
with PoE. AP can be ceiling or wall mount.
Specifications:
• CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz
• RAM: 512MB of DDR3
• Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WLAN:
2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
3 x GPIO-controlled System-LEDs
(form one virtual RGB System-LED)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An unpopulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, but it drops only
to a limited shell .
Installation Instructions:
black_small_square obtain serial access
black_small_square stop auto boot
black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot)
black_small_square bootm
black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi
to the device
black_small_square write the image to the NAND:
black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0)
black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs-
nand-factory.ubi
black_small_square reboot
Note: Device is not using dual partitioning (NAND contains other partitions
with different manufacture data etc.)
Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Redmi AX6 is a budget 802.11ax dual-band router/AP
Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 128MB NAND
* Ethernet: 4x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LEDs:
* System (Blue/Yellow)
* Network (Blue/Yellow)
*Buttons: 1x soft reset
*Power: 12V DC jack
Installation instructions:
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
6. Reboot the device by:
reboot
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: Zhijun You <hujy652@gmail.com>
Xiaomi AX3600 is a budget 802.11ax dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* WLAN:
* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
* System (Blue and Yellow)
* IoT (Blue)
* Network (Blue and Yellow)
* Buttons: 1x Soft reset
* Power: 12V DC Jack
Installation instructions:
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
6. Reboot the device by:
reboot
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Package ath11k firmware for AHB devices as well as QCN9074 which is a non
consumer card targeted as a companion for QCA WiSoC-s.
linux-firmware is always out of date for these, so fetch them from Kalle-s
repo like we do for ath10k.
Signed-off-by: Robert Marko <robimarko@gmail.com>
SOC: Qualcomm IPQ4019
WiFi 1: QCA4019 IEEE 802.11b/g/n
WiFi 2: QCA4019 IEEE 802.11a/n/ac
WiFi 3: QCA8888 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8811 (A12U)
Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L
Ethernet: Qualcomm Atheros QCA8072 (2-port)
Flash 1: Mactronix MX30LF4G18AC-XKI
RAM (NAND): SK hynix H5TC4G63CFR-PBA (512MB)
LED Controller: NXP PCA9633 (I2C)
Buttons: Single reset button (GPIO).
- The three WiFis were fully tested and are configured with the same settings as in the vendor firmware.
- The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream.
- Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working.
Bluetooth:
========
- Fully working with the following caveats:
- RFKILL need to be enabled in the kernel.
- An older version of bluez is needed as bccmd is needed to configure the chip.
Zigbee:
======
- The spidev device is available in the /dev directory.
- GPIOs are configured the same way as in the vendor firmware.
- Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working.
Installation:
=========
The squash-factory image can be installed via the Linksys Web UI:
1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device).
2. Login with your admin password.
3. To enter into the support mode, click on the "CA" link and the bottom of the page.
4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button.
5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups.
The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts.
If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row.
It can also be done via TFTP:
1. Setup a local TFTP server and configure its IP to 192.168.1.100.
2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server.
3. Connect to the device through the serial console.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2".
6. Once flashed, enter "reset" to reboot the device.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home).
Device specification
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz (QCA9982): a/n/ac, 3x3
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up)
Power: 5VDC, 2,1A via USB-C socket
Bootloader: U-Boot
On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software )
Installation
1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port,
with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) :
VCC (3.3V). Do not use unless you need to source power for the converer from it.
TX
RX
GND
Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1.
2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2
3.Connect TFTP server to RJ-45 port (WAN/LAN1).
4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb
bootm 0x84000000
5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do:
WEB PARITION
cat /dev/mtd8 > /tmp/mtd8.bin
scp /tmp/mtd8.bin root@YOURSERVERIP:/
rm /tmp/mtd8.bin
ROOT PARITION
cat /dev/mtd9 > /tmp/mtd9.bin
scp /tmp/mtd9.bin root@YOURSERVERIP:/
rm /tmp/mtd9.bin
If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command:
nand erase 0x1800000 0x1D00000
6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1):
ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it
7. Install image via :
sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin
previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward.
Back to Stock (!!! need original dump taken from initramfs !!!) -------------
Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2
Connect serial console (115200,8n1) to serial console connector .
Connect TFTP server to RJ-45 port (WAN/LAN1).
rename mtd8.bin to web.img and mtd9.bin to root_uImage_s
Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase Web and RootFS:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 root_uImage_s
nand erase 0x1800000 0x1D00000
nand write 0x84000000 0x1800000 0x1D00000
This will restore Web Interface:
tftpboot 0x84000000 web.img
nand erase 0x1000000 0x800000
nand write 0x84000000 0x1000000 0x800000
After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router
As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com
Signed-off-by: Marcin Gajda <mgajda@o2.pl>
It has been brought to my attention that recently added WCN6855 firmware
is broken as it is getting stripped during building due to being 2 ELF
binaries.
I am sure WCN6750 and any other ELF binaries are having the same issue,
so since stripping firmware binaries is clearly unwanted disable it.
Fixes: b4d3694f81 ("linux-firmware: package ath11k consumer cards firmware")
Signed-off-by: Robert Marko <robimarko@gmail.com>
WCN6855 exists in 2 HW revisions, but both use the same FW so upstream
just has a symlink for hw2.1 to hw2.0 that I forgot to make.
Fixes: b4d3694f81 ("linux-firmware: package ath11k consumer cards firmware")
Signed-off-by: Robert Marko <robimarko@gmail.com>
The symbolic link introduced in 22e9d8bc89 is wrong.
Fixes: 22e9d8bc89 ("cypress-firmware: use symlink to provide firmware in brcm")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
Since all NVRAM files in external repo are now upstreamed and to lower
future maintenance cost, disassociate the package from external source
repo.
All upstream pending NVRAM files shall be stored locally from now on.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[Remove outdated URL, add SPDX-License-Identifier]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
According to commit 6f6c2fb321, AP6335 module used in PICO-PI-IMX7D works
only with firmware from `linux-firmware`. However, firmware from
`cypress-firmware` suite is directly from the chip company (Infineon) and
is actually newer.
Instead of dropping the firmware from Infineon, create a package named
`brcmfmac-firmware-4339-sdio`, and keep the Infineon version of
`cypress-firmware-4339-sdio` around.
This gives us devs the option to choose. Also, it means that
- packages `brcmfmac-firmware-*` uniformly come from `linux-firmware`
- packages `cypress-firmware-*` uniformly come from `cypress-firmware`
so hopefully brings more clarity.
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
This is to align the implementation with upstream `linux-firmware`.
Some Raspberry Pi boards do not have dedicated NVRAM in `linux-firmware`
source repository, their NVRAM is provided through a symbolic link to
NVRAM of another board with an identical wireless design.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
This is to align the implementation with upstream `linux-firmware`.
Instead of moving these firmware files to `brcm` subdirectory and changing
their names, leave them in `cypress` subdirectory, keep their names intact
and use symbolic links to provide compatibility with Broadcom FullMAC
driver.
This gives more context to where the firmware comes from.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
This is to align the implementation with upstream `linux-firmware`.
Some Raspberry Pi boards do not have dedicated NVRAM in `linux-firmware`
source repository, their NVRAM is provided through a symbolic link to
NVRAM of another board with an identical wireless design.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
PROVIDES for these packages will cause ambiguity and circular dependency
in planned changes.
For example, if there is a package `brcmfmac-firmware-43455-sdio-rpi-cm4`
that depends on `brcmfmac-firmware-43455-sdio-rpi-4b`, there is no way to
tell which one of below packages the system will go for.
- package named `brcmfmac-firmware-43455-sdio-rpi-4b`
- package named `cypress-nvram-43455-sdio-rpi-4b` that PROVIDES
`brcmfmac-firmware-43455-sdio-rpi-4b`
When ambiguity is unacceptable, PROVIDES (aliases) shall be removed and
packages shall only be used through their exact name.
So remove PROVIDES and keep only CONFLICTS.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
Realtek bluetooth devices need firmware. Add packages for some of
these.
Tested on a WNDR3700v4 with rtl8761bu firmware.
Signed-off-by: Quintin Hill <stuff@quintin.me.uk>
Changes:
712460c linux-firmware: Update firmware file for Intel Bluetooth 9462
90d5f7e linux-firmware: Update firmware file for Intel Bluetooth 9462
48954ba linux-firmware: Update firmware file for Intel Bluetooth 9560
0e205fd linux-firmware: Update firmware file for Intel Bluetooth 9560
06b941e linux-firmware: Update firmware file for Intel Bluetooth AX201
ba958ff linux-firmware: Update firmware file for Intel Bluetooth AX201
02bdea2 linux-firmware: Update firmware file for Intel Bluetooth AX211
7044d46 linux-firmware: Update firmware file for Intel Bluetooth AX211
1b99bcd linux-firmware: Update firmware file for Intel Bluetooth AX210
4668ae9 linux-firmware: Update firmware file for Intel Bluetooth AX200
5bdfdba linux-firmware: Update firmware file for Intel Bluetooth AX201
b0f995c amdgpu: update DMCUB firmware for DCN 3.1.6
d991031 rtl_bt: Update RTL8822C BT UART firmware to 0xFFB8_ABD6
fd62f01 rtl_bt: Update RTL8822C BT USB firmware to 0xFFB8_ABD3
b15fc21 WHENCE: mrvl: prestera: Add WHENCE entries for newly updated 4.1 FW images
bf5a337 mrvl: prestera: Update Marvell Prestera Switchdev FW to v4.1
4a733c2 iwlwifi: add new FWs from core74_pv-60 release
7d2bb50 qcom: drop split a530_zap firmware file
7d56713 qcom/vpu-1.0: drop split firmware in favour of the mbn file
1431496 qcom/venus-4.2: drop split firmware in favour of the mbn file
cf95783 qcom/venus-4.2: replace split firmware with the mbn file
1fe6f49 qcom/venus-1.8: replace split firmware with the mbn file
abc0302 linux-firmware: Add firmware for Cirrus CS35L41 on new ASUS Laptop
20d9516 iwlwifi: add new PNVM binaries from core74-44 release
06dbfbc iwlwifi: add new FWs from core69-81 release
05df8e6 qcom: update venus firmware files for VPU-2.0
cd6fcdb qcom: remove split SC7280 venus firmware images
1612706 qcom: update venus firmware file for v5.4
ad9fdba qcom: replace split SC7180 venus firmware images with symlink
dae5d46 rtw89: 8852b: update fw to v0.27.32.1
a8e86ec rtlwifi: update firmware for rtl8192eu to v35.7
9aa8db1 rtlwifi: Add firmware v4.0 for RTL8188FU
8f86b5a i915: Add HuC 7.10.3 for DG2
48407ff cnm: update chips&media wave521c firmware.
bd31846 brcm: add symlink for Pi Zero 2 W NVRAM file
771968c linux-firmware: Add firmware for Cirrus CS35L41 on ASUS Laptops
6f9620e linux-firmware: Add firmware for Cirrus CS35L41 on Lenovo Laptops
1d18cb9 linux-firmware: Add firmware for Cirrus CS35L41 on HP Laptops
e497757 rtw89: 8852b: add initial fw v0.27.32.0
98b5577 iwlwifi: add new FWs from core72-129 release
604026c iwlwifi: update 9000-family firmwares to core72-129
Signed-off-by: Nick Hainke <vincent@systemli.org>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2
USB: 1 x USB 3.0 port
Button: 1 x Reset button
Switch: 1 x Mode switch
LED: 1 x Blue LED + 1 x White LED
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi
(IPQ40xx) # nand erase 0 0x8000000
(IPQ40xx) # nand write 0x84000000 0 $filesize
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
Get rid of drivers that are either limited to 802.11b/g or don't even support
cfg80211/mac80211. Most of these are either limited to boards that we don't even
support anymore because of firmware size, or were only used for custom hacks by
a really small number of users in the past.
Let's get rid of those to reduce the maintenance effort and the number of useless
packages
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).
Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.
There are currently two hardware revisions, which
differ on the 5Ghz radio:
AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz
Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
(QCA9984): a/n/ac, 4x4 HW REV AT1
(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot
Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
(refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert to
stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:
WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin
ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin
6. Login via ssh or serial and remove stock partitions
(default IP 192.168.0.1):
# this can return an error, if ubi was attached before
# or rootfs part was erased before.
ubiattach -m 17
# it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
# some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. download and install image via sysupgrade -n
(either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
to the device's /tmp directory)
sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin
Sometimes it could print ubi attach error, but please ignore it
if process goes forward.
Flash Layout
NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"
SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"
Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
for the device on a TFTP in the server's root.
This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize
This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize
After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac
(WiFi-5) wireless function, based on IPQ4019.
Specification:
- SoC : Qualcomm IPQ4019
- RAM : DDR3 512 MiB (H5TC4G63EFR)
- Flash : eMMC 4 GiB (THGBMNG5D1LBAIT)
- WLAN : 2.4/5 GHz 2T2R (IPQ4019)
- Ethernet : 10/100/1000 Mbps x2
- Transceiver : Qualcomm QCA8072
- WWAN : Telit LN940A9
- Z-Wave : Silicon Labs ZM5101
- Bluetooth : Qualcomm CSR8811
- Audio DAC : Realtek ALC5629
- Audio Amp. : Realtek ALC1304
- Voice Input Processor : Conexant CX20924
- Micro Controller Unit : Nuvoton MINI54FDE
- RGB LED, Fan, Temp. sensors
- Touch Sensor : Cypress CY8C4014LQI
- RGB LED driver : TI LP55231 (2x)
- LEDs/Keys : 11x, 6x
- UART : through-hole on PCB
- J1: 3.3V, TX, RX, GND from tri-angle marking
- 115200n8
- Power : 12 VDC, 2.5 A
Flash instruction using initramfs image:
1. Prepare TFTP server with the IP address 192.168.132.100 and place the
initramfs image to TFTP directory with the name "C0A88401.img"
2. Boot NCP-HG100/Cellular and interrupt after the message
"Hit any key to stop autoboot: 2"
3. Perform the following commands and set bootcmd to allow booting from
eMMC
setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000"
saveenv
4. Perform the following command to load/boot the OpenWrt initramfs image
tftpboot && bootm
5. On the initramfs image, perform sysupgrade with the sysupgrade image
(if needed, backup eMMC partitions by dd command and download to
other place before performing sysupgrade)
6. Wait for ~120 seconds to complete flashing
Known issues:
- There are no drivers for audio-related chips/functions in Linux Kernel
and OpenWrt, they cannot be used.
- There is no driver for MINI54FDE Micro-Controller Unit, customized for
this device by the firmware in the MCU. This chip controls the
following functions, but they cannot be controlled in OpenWrt.
- RGB LED
- Fan
this fan is controlled automatically by MCU by default, without
driver
- Thermal Sensors (2x)
- Currently, there is no driver or tool for CY8C4014LQI and cannot be
controlled. It cannot be exited from "booting mode" and moved to "normal
op mode" after booting. And also, the 4x buttons (mic mute, vol down,
vol up, alexa trigger) connected to the IC cannot be controlled.
- it can be exited from "booting mode" by installing and executing
i2cset command:
opkg update
opkg install i2c-tools
i2cset -y 1 0x14 0xf 1
- There is a connection issue on the control by uqmi for the WWAN module.
But modemmanager can be used without any issues and the use of it is
recommended.
- With the F2FS format, too many errors are reported on erasing eMMC
partition "rootfs_data" while booting:
[ 1.360270] sdhci: Secure Digital Host Controller Interface driver
[ 1.363636] sdhci: Copyright(c) Pierre Ossman
[ 1.369730] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO
...
[ 1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
[ 1.528325] mmc0: new HS200 MMC card at address 0001
[ 1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB
[ 1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB
[ 1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB
[ 1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0)
[ 1.550323] Alternate GPT is invalid, using primary GPT.
[ 1.561669] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17
...
[ 8.841400] mount_root: loading kmods from internal overlay
[ 8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 9.240465] block: attempting to load /etc/config/fstab
[ 9.246722] block: unable to load configuration (fstab: Entry not found)
[ 9.246863] block: no usable configuration
[ 9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet
[ 9.438915] urandom_read: 5 callbacks suppressed
[ 9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read)
[ 12.243332] mmc_erase: erase error -110, status 0x800
[ 12.246638] mmc0: cache flush error -110
[ 15.134585] mmc_erase: erase error -110, status 0x800
[ 15.135891] mmc_erase: group start error -110, status 0x0
[ 15.139850] mmc_erase: group start error -110, status 0x0
...(too many the same errors)...
[ 17.350811] mmc_erase: group start error -110, status 0x0
[ 17.356197] mmc_erase: group start error -110, status 0x0
[ 17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00
[ 17.446910] mmc0: tuning execution failed: -5
[ 17.447111] mmc0: cache flush error -110
[ 18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint
[ 18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b
[ 18.198691] block: attempting to load /etc/config/fstab
[ 18.198972] block: unable to load configuration (fstab: Entry not found)
[ 18.203029] block: no usable configuration
[ 18.211371] mount_root: overlay filesystem has not been fully initialized yet
[ 18.214487] mount_root: switching to f2fs overlay
So, this support uses ext4 format instead which has no errors.
Note:
- The primary uart is shared for debug console and Z-Wave chip. The
function is switched by GPIO15 (Linux: 427).
value:
1: debug console
0: Z-Wave
- NCP-HG100/Cellular has 2x os-image pairs in eMMC.
- 0:HLOS, rootfs
- 0:HLOS_1, rootfs_1
In OpenWrt, the first image pair is used.
- "bootipq" command in U-Boot requires authentication with signed-image
by default. To boot unsigned image of OpenWrt, use "mmc read" and
"bootm" command instead.
- This support is for "Cellular" variant of NCP-HG100 and not tested on
"WLAN" (non-cellular) variant.
- The board files of ipq-wifi may also be used in "WLAN" variant of
NCP-HG100, but unconfirmed and add files as for "Cellular" variant.
- "NET" LED is used to indicate WWAN status in stock firmware.
- There is no MAC address information in the label on the case, use the
address included in UUID in the label as "label-MAC" instead.
- The "CLOUD" LEDs are partially used for indication of system status in
stock firmware, use they as status LEDs in OpenWrt instead of RGB LED
connected to the MCU.
MAC addresses:
LAN : 5C:FF:35:**:**:ED (ART, 0x6 (hex))
WAN : 5C:FF:35:**:**:EF (ART, 0x0 (hex))
2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex))
5 GHz : 5C:FF:35:**:**:EE (ART, 0x5006 (hex))
partition layout in eMMC (by fdisk, GPT):
Disk /dev/mmcblk0: 7733248 sectors, 3776M
Logical sector size: 512
Disk identifier (GUID): ****
Partition table holds up to 20 entries
First usable sector is 34, last usable sector is 7634910
Number Start (sector) End (sector) Size Name
1 34 1057 512K 0:SBL1
2 1058 2081 512K 0:BOOTCONFIG
3 2082 3105 512K 0:QSEE
4 3106 4129 512K 0:QSEE_1
5 4130 4641 256K 0:CDT
6 4642 5153 256K 0:CDT_1
7 5154 6177 512K 0:BOOTCONFIG1
8 6178 6689 256K 0:APPSBLENV
9 6690 8737 1024K 0:APPSBL
10 8738 10785 1024K 0:APPSBL_1
11 10786 11297 256K 0:ART
12 11298 11809 256K 0:HSEE
13 11810 28193 8192K 0:HLOS
14 28194 44577 8192K 0:HLOS_1
15 44578 306721 128M rootfs
16 306722 568865 128M rootfs_1
17 568866 3958065 1654M rootfs_data
[initial work]
Signed-off-by: Iwao Yuki <dev.clef@gmail.com>
Co-developed-by: Iwao Yuki <dev.clef@gmail.com>
[adjustments, cleanups, commit message, sending patch]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(dropped clk_unused_ignore, dropped 901-* patches, renamed
key nodes, changed LEDs chan/labels to match func-en, made
:net -> (w)wan leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This package downloads raw files
which have names that are not corresponding to
the name and version of the package
as it is defined in the Makefile.
Use the option DL_SUBDIR to set the DL_DIR
to be a subdirectory named with
PKG_NAME and PKG_RELEASE
to better organize the downloads.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This package downloads raw files
which have names that are not corresponding to
the name and version of the package
as it is defined in the Makefile.
Use the option DL_SUBDIR to set the DL_DIR
to be a subdirectory named with
PKG_NAME and PKG_VERSION
to better organize the downloads.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This package downloads raw files
which have names that are not corresponding to
the name and version of the package
as it is defined in the Makefile.
Use the option DL_SUBDIR to set the DL_DIR
to be a subdirectory named with
PKG_NAME and PKG_VERSION
to better organize the downloads.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
btusb fails to start on MT792[12] hardware without the appropriate
firmware being loaded first:
[ 9.750285] bluetooth hci0: Direct firmware load for mediatek/BT_RAM_CODE_MT7961_1_2_hdr.bin failed with error -2
[ 9.765723] bluetooth hci0: Falling back to sysfs fallback for: mediatek/BT_RAM_CODE_MT7961_1_2_hdr.bin
Package firmware for MediaTek MT792[12] Bluetooth from linux-firmware.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The R8712U driver depends on cfg80211. cfg80211 is provided by mac80211
backports, we can not build any in kernel drivers which depend on
cfg80211 which is an out of tree module in OpenWrt.
The cfg80211 dependency was added with kernel 5.9.
We could add rtl8192su to backports and build it from there.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The change of the PKG_VERSION caused the hash of the package to
change. This is because the PKG_VERSION is present in the
internal directory structure of the archive.
Fixes: e879cccaa2 ("uboot-layerscape: update PKG_HASH")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
those board files can/should be dropped now too.
Fixes: 50c232d6f4 ("ipq-wifi: drop upstreamed board-2.bin")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
