Backort upstream patch which preserves oif of IPv6 link scoped packets.
The outgoing interface of IPv6 link scope packets can be changed by the
function ip6_route_me_harder. This is unwanted behavior for link local
packets and multicast packets as the outgoing interface is fixed and must
not be altered as it can break neighbor discovery and multicast listener
discovery.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Alberto Bursi reported:
>The patch "ipq40xx: specify "firmware" partition format for GL.iNet GL-B1300"
>prevents boot on my B1300. I compiled from latest sources.
The GL-B1300 was using the discouraged direct subnodes method to declare
the partitions on the flash.
|The partition table should be a subnode of the flash node and should be named
|'partitions'. This node should have the following property:
|- compatible : (required) must be "fixed-partitions"
|Partitions are then defined in subnodes of the partitions node.
|
|For backwards compatibility partitions as direct subnodes of the flash device are
|supported. This use is discouraged.
|NOTE: also for backwards compatibility, direct subnodes that have a compatible
|string are not considered partitions, as they may be used for other bindings.
<https://www.kernel.org/doc/Documentation/devicetree/bindings/mtd/partition.txt>
Hence, this patch converts the device to the "partitions" layout.
Fixes: 1cbe457cf9 ("ipq40xx: specify "firmware" partition format for GL.iNet GL-B1300")
Reported-by: Alberto Bursi <bobafetthotmail@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Since commit 61b5b4971e ("mac80211: make ath10k-ct the default ath10k")
select ath10k-ct and the -ct firmwares by default.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Backport net: Allow class-e address assignment via ifconfig ioctl
While most distributions long ago switched to the iproute2 suite
of utilities, which allow class-e (240.0.0.0/4) address assignment,
distributions relying on busybox, toybox and other forms of
ifconfig cannot assign class-e addresses without this kernel patch.
While CIDR has been obsolete for 2 decades, and a survey of all the
open source code in the world shows the IN_whatever macros are also
obsolete... rather than obsolete CIDR from this ioctl entirely, this
patch merely enables class-e assignment, sanely.
https://git.kernel.org/pub/scm/linux/kernel/git/davem/net.git/commit/?id=65cab850f0eeaa9180bd2e10a231964f33743edf
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
>From the Documentation/devicetree/bindings/leds/common.txt:
- default-state : The initial state of the LED. Valid values are "on", "off",
and "keep". If the LED is already on or off and the default-state property is
set the to same value, then no glitch should be produced where the LED
momentarily turns off (or on). The "keep" setting will keep the LED at
whatever its current state is, without producing a glitch. The default is
off if this property is not present.
So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch adds support for TP-Link Archer A7
Specification:
- SOC: QCA9563
- Flash: 16 MiB (SPI)
- RAM: 128 MiB (DDR2)
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) SoC internal
- 5GHz (ac) QCA988x
- USB: 1x USB 2.0 port
- Button: 1x power, 1x reset, 1x wps
- LED: 10x LEDs
- UART: holes in PCB
- Vcc, GND, RX, TX from ethernet port side
- 115200n8
Flash instructions:
Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin
via the Webinterface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the Archer A7
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the tftp
root directory renamed to ArcherC7v5_tp_recovery.bin
2. Connect power cable to Archer A7, press and hold the reset button
and turn the router on
3. Keep the reset button pressed for ~5 seconds
4. Wait ~150 seconds to complete flashing
Changes since first revision:
- Flash instructions using stock image webinterface
- Changed "Version 5" in model string to "v5"
- Split DTS file in qca9563_tplink_archer-x7-v5.dtsi
and qca9563_tplink_archer-a7-v5.dts
- Firmware image is now build with dynamic partitioning
- Default to ath10k-ct
Changes since second revision:
- Changed uboot@0 to uboot@20000 in DTS file
- Fixed ordering issue in board led script
- Specify firmware partition format in DTS file
- Rebased Makefile device definition on common
Device/tplink-safeloader-uimage definition
- Merged switch section in network script
(same configuration as tplink,tl-wdr3600
and tplink,tl-wdr4300)
Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
This patch fixes wrong usage of debounce-interval subnode property of
gpio-keys-polled nodes, which was used inproperly in parent node, but it
belongs to the subnodes, excerpt from the docs:
Optional subnode-properties:
- debounce-interval: Debouncing interval time in milliseconds.
If not specified defaults to 5.
And the docs are up to date as the source code matches that description
as well:
if (fwnode_property_read_u32(child, "debounce-interval",
&button->debounce_interval))
button->debounce_interval = 5;
While at it, I've also re-formatted gpio-keys-polled nodes, usually just
adding new lines after every key subnode.
Cc: Tomasz Maciej Nowak <tomek_n@o2.pl>
Cc: Matt Merhar <mattmerhar@protonmail.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently it's quite hard to diff debugging output between ar71xx and
ath79, so this patch tries to improve it by adding the same
ag71xx_dump_regs function and placing debugging output from the
registers to relatively same places.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since commit 8e9a59a6b9 (build: add
mkrasimage) a proper factory image can be provided for the ZyXEL
NBG6817, which can be flashed from the OEM firmware or used for
tftp based push-button recovery, therefore the previously used
partition images for mmcblk0p5-rootfs.bin and mmcblk0p4-kernel.bin
are no longer required (and using them properly has always been
slightly difficult and risky) and can now be dropped from the image
generation code.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79.
They're pretty much identical, except dir-835-a1 has less LEDs.
The routers come with 128 MByte of RAM and 16 MBytes of flash and sport
2.4GHz and 5.0GHz wireless. Both routers have entries already in
OpenWrt's TOH. Please check there for more information on these
antiquities.
https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1
Installation:
1. Connect to the web interface of the vendor firmware (usually
listening on 192.168.0.1).
2. Go to "Tools", then "Firmware".
3. In the "Firmware Upgrade" box click "Browse".
4. Select the OpenWrt factory image for your router.
5. Click "Upload", confirm the popups if you agree to flash the file you
selected.
6. Wait for firmware upgrade to complete. It takes about 5 minutes.
Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't
have this router so I can't confirm.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial changes]
This command enables factory image generation for Cameo boards. On
upgrade the vendor firmware will check the size of the provided image
and if a specific string is located at the end of the binary.
cameo-factory will generate an image that the vendor firmware accepts.
Tested on a D-Link DIR-825 C1 with vendor firmwares 3.01 and 3.04.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
- replace licence texts with SPDX-License-Identifier where
applicable.
- make node-names more generic to fit with Device-Tree Release v0.2
Section 2.2.2 Generic Names Recommendation.
- utilize wifi0/1, blsp1_uart1 labels
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In the upstream netdev led trigger the one mode file was replaced by 3
files named rx, tx and link. Fix the netdev trigger configuration code
to use the modified API.
Fixes: aa3b6a08c5 ("kernel: Replace ledtrig-netdev with upstream backport")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 216397b812.
Due to:
Package ip-tiny is missing dependencies for the following libraries:
libelf.so.1
Makefile:187: recipe for target '/var/lib/buildbot/slaves/slave-lede-builds4/mips_24kc/build/sdk/bin/packages/mips_24kc/base/ip-tiny_4.19.0-6_mips_24kc.ipk' failed
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This activates the CONFIG_USB_SUPPORT option in the in the gemini kernel
again which will provide the core USB support and makes it possible to
compile the rest of the USB parts into modules. Without this change USB
will not be available in the gemini target and some modules fail to
compile because the feature list indicates USB support.
Fixes: 10ec966f7b ("gemini: Break out USB to packages")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The eapol-test application also uses the code with the newly activated
ubus support, add the missing dependency.
Fixes: f5753aae23 ("hostapd: add support for WPS pushbutton station")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ufb tool needs the host UAPI Linux headers from kernel 3.18
or later, remove it for now as it is not used anyway.
Fixes: 4bf5c4395b ("tools/sdimage: update to latest git version")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
mbedtls uses some instructions introduced in ARMv6 which are not
available in older architectures.
Fixes: 3f7dd06fd8 ("mbedtls: Update to 2.14.1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Netgear R6350 is a wireless router, aka Netgear AC1750.
Specification:
- SoC: Mediatek MT7621AT (2 CPU cores, 4 threads)
- RAM: 128MiB (Nanya NT5CC64M16GP-DI)
- ROM: 128MiB NAND Flash (Macronix MX30LF1G18AC-TI)
- Wireless:
for 11b/g/n (upto 300Mbps): MT7603
for 11a/ac (upto 1450Mbps) : MT7615, is not avaliable now
- Ethernet LAN speed: up to 1000Mbps
- Ethernet LAN ports: 4
- Ethernet WAN speed: up to 1000Mbps
- Ethernet WAN ports: 1
- USB ports: 1 (USB 2.0)
- LEDs: 4 (all can be controlled by SoC's GPIO)
- buttons: 2
- serial ports: unknown
Installation through telnet:
- Copy kernel.bin and rootfs.bin to a USB flash disk,
plug to usb port on the router.
- Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
(login if required, default: admin password)
- You will see "Debug Enabled!"
- Telnet 192.168.1.1 and login with "root"
- ls /mnt/shares/ to find out path of your USB disk.
'myUdisk' for example.
- cd /mnt/shares/myUdisk
- mtd_write write rootfs.bin Rootfs
- mtd_write write kernel.bin Kernel
- reboot
recovery when bricked:
nmrpflash can be used to recover to the netgear firmware
if a broken image was flashed.
The SC_PART_MAP partition suggests that an on flash partition table
exists. After implementing a partition parser/builder for the sercom
partition format, the definitions don't match the flash layout used by
the stock firmware.
It either means the partition format has not yet been completely
understood or it isn't used by the stock firmware. For now, use fixed
partitions instead.
Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[apply latest ramips changes and document the on flash partition map
issues]
Signed-off-by: Mathias Kresin <dev@kresin.me>
I've sent this one upstream. This patch is critical if you want to run
with "prove lock correctness" (lockdep) and you happen to have certain
mtd devices. The misuse of the uninitialized object is undefined
behaviour, but being zeroed it does not appear to have actually broken
anything other than the lockdep engine.
Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
This includes code cleanups and fixes some portability issues,
compiler warnings about printf arguments etc.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Update mbedtls to 2.14.1
This fixes:
* CVE-2018-19608: Local timing attack on RSA decryption
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[Update to 2.14.1]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disable Marvell's hardware level MAC learning because it breaks station roaming.
When enabled it drops all frames that arrive from a MAC address
that is on a different port at learning table.
Problem description:
Multiple APs with inter-AP roaming connected to different ports,
when station moves from one AP on one port to another AP on another port,
traffic flow breaks down because the learning table is not updated.
Signed-off-by: Anderson Luiz Alves <alacn1@gmail.com>
[Replaced with upstream version, move to generic]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes these warnings:
swlib.c:455:18: warning: implicit declaration of function 'isspace'
swlib.c:461:9: warning: implicit declaration of function 'isdigit'
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Added two upstream mailing list patches that fix behavior under big endian
systems. Issue was present since version 1.11.0.
Tested on Turris Omnia.
Original discussion: https://github.com/openwrt/openwrt/pull/1575
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The current stats always have a 'ms' suffix, and they're used by luci.
Introduce dsl.latency_[down|up] values, exported in µs without suffix.
Signed-off-by: Andre Heider <a.heider@gmail.com>
