Select MT7996 2+3+3 firmware for the Adtran SmartRG SDG-8733A device
and also add it to the image for the BPi-R4 which supports both,
BE19000 (4+5+5) as well as BE14000 (2+3+3) Wi-Fi 7 modules.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
1231d45dcb5e wifi: mt76: mt7915: check devm_kasprintf() returned value
042082027b3f wifi: mt76: mt7921: Check devm_kasprintf() returned value
4a95c1a81eee wifi: mt76: Avoid multiple -Wflex-array-member-not-at-end warnings
5fdb1841f726 wifi: mt76: mt7925: fix a potential association failure upon resuming
eeb51b527377 wifi: mt76: mt7925: convert comma to semicolon
d4b3b302ceb9 wifi: mt76: mt7615: check devm_kasprintf() returned value
922e515bd8e0 wifi: mt76: mt7925: fix a potential array-index-out-of-bounds issue for clc
bec8cb851d99 wifi: mt76: mt7925: replace chan config with extend txpower config for clc
d10ce9d65dac wifi: mt76: remove mt76_calculate_default_rate()
6685a2f4c217 wifi: mt76: mt7996: remove phy->monitor_vif
a2a9d9826277 wifi: mt76: do not increase mcu skb refcount if retry is not supported
059342ca6a68 wifi: mt76: move mt76_tm_policy to from testmode.h to mt76.h
8bef11443290 wifi: mac80211: inform the low level if drv_stop() is a suspend
4b16d2bfdcbd wifi: mac80211: handle color change per link
4529cddb6718 wifi: mt76: mt7996: extend flexibility of mt7996_mcu_get_eeprom()
4364571e4b2b wifi: mt76: mt7996: add support for more variants
8c86aa304ea1 wifi: mt76: mt7996: set correct background radar capability
addfbd141863 firmware: add latest mt7996 + mt7992 firmware
5ba4981f8b92 wifi: mt76: mt792x: add P2P_DEVICE support
dc32780c7fcd wifi: mt76: mt7921s: fix a potential firmware freeze during startup
7b5d653ea90e wifi: mt76: mt7925: fix off by one in mt7925_load_clc()
1e57d2da94c9 wifi: mt76: mt7615: Convert comma to semicolon
7aca94abac47 wifi: mt76: mt7915: fix slot time for 5/6GHz
e3e6d490ab90 wifi: mt76: mt7915: Fix mesh scan on MT7916 DBDC
ee693260c521 firmware: move mt7996 firmware to the right place
867accf4f4aa wifi: mt76: mt7996: Add eht radiotap tlv
7c4d6e403381 wifi: mt76: Fix EHT NSS radiotap reporting.
71c3949fa8ac wifi: mt76: mt7921: fix a potential scan no APs
61641da04c9e mt76: mt76u_vendor_request: Do not print error messages when -EPROTO
680bc70f161f wifi: mt76: mt7921: fix using incorrect group cipher after disconnection.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This driver does not support more than 1 queue.
Fixes: ba24b94e0b ("ramips: use more devm in mtk_eth_soc")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This script hasn't seen an update in multiple years, update it to the
latest version provided upstream.
Both `config.guess` and `config.sub` are copied from upstream[1] and not
modified.
The full changelog is available within the upstream repository[1].
[1]: https://git.savannah.gnu.org/git/config.git
Link: https://github.com/openwrt/openwrt/pull/16536
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are cases where an unavailable port is not an error, making
this error message a false-positive. The kernel log is flooded with
the messages like:
OF: graph: no port node found in /soc@0/bus@42000000/i2c@42530000/usb-typec@50
Silence this message by making it a debug message.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16524
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some new targets were added, but we did not add them to the labeler.
Add them now.
Link: https://github.com/openwrt/openwrt/pull/16454
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The type 'id_t' check has been moved to configure.ac in upstream commit:
819063eb4d27 ("test for id_t with autoconf instead of blind typedef, fixes FTBFS on FreeBSD")
changelog:
e4780b1aad/debian/changelog
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16530
Signed-off-by: Nick Hainke <vincent@systemli.org>
Some setups have alternate boot actions in case the main OS fails to
boot. These can include a secondary copy of the OS, a recovery OS, a
fallback to TFTP boot, etc.
This commit invalidates the kernel image while rootfs is being written
which, if a sysupgrade is interrupted, will trigger an alternate boot
action in devices that support it. This results in safer sysupgrades.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
The only supported kernel in the main branch now is version 6.6. It's
time to clean up these useless codes and patches.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The virtio_find_vqs() ABI has been changed since the 6.11 kernel.
Switch back to using the old ABI to fix the build error:
../mac80211-regular/backports-6.11/drivers/net/wireless/virtual/mac80211_hwsim.c: In function 'init_vqs':
../mac80211-regular/backports-6.11/drivers/net/wireless/virtual/mac80211_hwsim.c:6632:31: error: array type has incomplete element type 'struct virtqueue_info'
6632 | struct virtqueue_info vqs_info[HWSIM_NUM_VQS] = {
| ^~~~~~~~
../mac80211-regular/backports-6.11/drivers/net/wireless/virtual/mac80211_hwsim.c:6637:16: error: too few arguments to function 'virtio_find_vqs'
6637 | return virtio_find_vqs(vdev, HWSIM_NUM_VQS,
| ^~~~~~~~~~~~~~~
In file included from ../mac80211-regular/backports-6.11/drivers/net/wireless/virtual/mac80211_hwsim.c:38:
./include/linux/virtio_config.h:224:5: note: declared here
224 | int virtio_find_vqs(struct virtio_device *vdev, unsigned nvqs,
| ^~~~~~~~~~~~~~~
../mac80211-regular/backports-6.11/drivers/net/wireless/virtual/mac80211_hwsim.c:6632:31: error: unused variable 'vqs_info' [-Werror=unused-variable]
6632 | struct virtqueue_info vqs_info[HWSIM_NUM_VQS] = {
| ^~~~~~~~
../mac80211-regular/backports-6.11/drivers/net/wireless/virtual/mac80211_hwsim.c:6639:1: error: control reaches end of non-void function [-Werror=return-type]
6639 | }
| ^
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This fixes some corner cases triggered by enabling fraglist GRO, where some
protocols may accidentally or intentionally linearize fraglist skbs.
Previously, these skbs became unusable and segmenting them led to crashes.
With this patch, they are properly handled by passing them to skb_segment
instead of skb_segment_list.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
New releases of openssl are only published on GitHub, and official
downloads are also redirected to GitHub. So remove the old download
mirrors (file 404), and replace the current address with https.
Link: https://openssl-library.org/source/
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16470
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These got added to the kernel after this driver was written.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16415
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It automatically adds the error code at the end of the message. It also
deals with -EPROBE_DEFER automatically (doesn't output). Simpler code.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16350
Signed-off-by: Robert Marko <robimarko@gmail.com>
After digging in the history of the e2fsck exit code patch, it seems like
there is no reason for us to carry this patch so lets drop it.
Link: https://github.com/openwrt/openwrt/pull/16500
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, e2fsprogs is being patched to avoid detecting host crond, but
instead of doing that we can simply pass --with-crond-dir=no as an
argument and drop the patch.
Link: https://github.com/openwrt/openwrt/pull/16500
Signed-off-by: Robert Marko <robimarko@gmail.com>
Considering that this patch to not build e4defrag was added 12 years ago
because:
Compilation fails on older systems due to missing syscalls
I think its safe to say that enough time is passed so that whatever those
older systems were are either updated or not used anymore so lets drop
the patch.
Link: https://github.com/openwrt/openwrt/pull/16500
Signed-off-by: Robert Marko <robimarko@gmail.com>
General hardware info:
----------------------
D-Link DGS-1210-28P rev. F1 is a switch with 24 ethernet ports and 4
combo ports, all ports Gbit capable. It is based on a RTL8382 SoC
@500MHz, DRAM 128MB and 32MB flash. 24 ethernet ports are 802.3af/at PoE
capable with a total PoE power budget of 193W.
Power over Ethernet:
--------------------
The PSE hardware consists of three BCM59121 PSE chips, serving 8 ports
each. They are controlled by a Nuvoton MCU. In order to enable PoE, the
realtek-poe package is required. It is installed by default, but
currently it requires the manual editing of /etc/config/poe. Keep in
mind that the port number assignment does not match on this switch,
alway 8 ports are in reversed order: 8-1, 16-9 and 24-17.
LEDs and Buttons:
-----------------
On stock firmware, the mode button is supposed to switch the LED
indicators of all port LEDs between Link Activity and PoE status. The
currently selected mode is visualized using the respective LEDs. PoE Max
indicates that the maximum PoE budget has been reached. Since there is
currently no support for this behavior, these LEDs and the mode button
can be used independently.
Serial connection:
------------------
The UART for the SoC (115200 8N1) is available via unpopulated standard
0.1" pin header marked J6. Pin1 is marked with arrow and square.
Pin 1: Vcc 3.3V
Pin 2: Tx
Pin 3: Rx
Pin 4: Gnd
OEM installation from Web Interface:
------------------------------------
1. Make sure you are booting using OEM in image 2 slot. If not,
switch to
image2 using the menus
System > Firmware Information > Boot from image2
Tools > reboot
2. Upload image in vendor firmware via Tools > Backup / Upgrade
Firmware > image1
3. Toggle startup image via System > Firmware Information > Boot
from
image1
4. Tools > reboot
Other installation methods not tested, but since the device shares the
board with the DGS-1210-28, the following should work:
Boot initramfs image from U-Boot:
---------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000
openwrt-rtl838x-generic-d-link_dgs-1210-28p-f-initramfs-kernel.bin`
command
5. Boot the image with `bootm` command
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15938
Signed-off-by: Sander Vanheule <sander@svanheule.net>
flex currently leaks the path of m4 as found on the build host.
While it is possible to override this using the M4 environment
variable (which we always did for autotools based builds) when
using CMake or Ninja the M4 variable is not set.
One easy fix is to make flex take STAGING_DIR_HOST into account
and expect m4 there if that variable is set in the environment.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Platform specified fiptool files was moved before lf-6.6.23-2.0.0 bump.
But PLAT_FIPTOOL_HELPER_MK still pointed to old location.
This cause problems with ls-ddr-phy build.
This patch fix PLAT_FIPTOOL_HELPER_MK path.
Fixes: 0ec659bd2b ("tfa-layerscape: Bump to lf-6.6.23-2.0.0")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16472
Signed-off-by: Robert Marko <robimarko@gmail.com>
Always depend on PCI and don't build on platforms
without PCI.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16475
Signed-off-by: Robert Marko <robimarko@gmail.com>
* Version 5 of this action updated the runtime to Node.js 20.
All scripts are now run with Node.js 20 instead of Node.js 16
and are affected by any breaking changes between Node.js 16 and 20.
* adapt the labeler configuration to the new format
Follow-up to #16251 this was reverted with b870c16534
Link: https://github.com/openwrt/openwrt/pull/16451
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16451
Signed-off-by: Robert Marko <robimarko@gmail.com>
The rss variant should conflict with the default.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16460
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The rss variant should conflict with the default.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16460
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Before this commit, sysupgrade saved the settings backup data to
the area following rootfs even though the device has an actual
rootfs_data partition. The backup data was completely ignored on
the following boot, but since rootfs_data was not being cleared
during sysupgrade, the issue was not noticed earlier.
Note that this commit changes the filesystem of rootfs_data from
ext4 to F2FS (if OEM partitioning is used).
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16463
Signed-off-by: Robert Marko <robimarko@gmail.com>
This board is also as known as Bananapi BPi-M7.
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
8/16/32GB LPDDR4/LPDDR4x RAM
2x 2500 Base-T (PCIe, rtl8125b)
2 LEDs (RED / GREEN)
16GB/32GB/64GB/128GB eMMC on-board
Micro-SD Slot
USB 2.0 Port
USB 3.0 Port
M.2 M-Key
40-Pin Header
USB PD 2.0 9/12/15V Power
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16462
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add support for the ArmSoM Sige7 board.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16462
Signed-off-by: Nick Hainke <vincent@systemli.org>
of_property_read_u32 returns -EINVAL when property does not exist,
according to the documentation -ENOENT is not a valid return code.
So, instead of checking for -ENOENT check for -EINVAL as otherwise the
blamed commit breaks AQR probe since it will return -EINVAL during probe.
Fixes: cb2a11f49c ("generic: phy: aquantia: add pending patch to force MDI pair order")
Link: https://github.com/openwrt/openwrt/pull/16466
Signed-off-by: Robert Marko <robimarko@gmail.com>
Avoids having to handle EPROBE_DEFER manually.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16456
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing ksym CONFIG_RUST
Building r27563 without this commit will fail due to this ksym
being undefined in the generic config.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16464
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix ltssm crashes on BPI-Rx boards.
Seems read32/write32 using wrong address which
is not a problem on x86/64 PCI controllers.
But have issues on BPI-Rx boards.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15945
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allow to build ath11k and other drivers using
qcom-qmi-helpers together (eg. ath12k).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15945
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
