This adds some still-missing board names for old TP-Link devices
to ath79 SUPPORTED_DEVICES.
Fixes: FS#3017
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device seems to be identical to the TL-WDR4300, just with
different release date/region and TPLINK_HWID.
Support is added based on the ar71xx implementation.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer D7 v1 is a dual-band AC1750 router + modem.
The router section is based on Qualcomm/Atheros QCA9558 + QCA9880.
The "DSL" section is based on BCM6318 but it's currently not supported.
The Archer D7b seems to differ from the Archer D7 only in the
partition table.
Router section - Specification:
775/650/258 MHz (CPU/DDR/AHB)
128 MB of RAM (DDR2)
16 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
4x 10/100/1000 Mbps Ethernet
7x LED, 2x button
UART header on PCB
Known issues:
- Broadband LED (missing GPIO - probably driven by the BCM6318)
- Internet LED (missing GPIO - probably driven by the BCM6318)
- WIFI LED (working only for one interface at a time, while in the
OEM firmware works for both wifi interfaces; thus, this patch does
not set a trigger by default)
- DSL not working (eth0)
UART connection
---------------
J1 HEADER (Qualcomm CPU)
. VCC
. GND
. RX
O TX
J41 HEADER (Broadcom CPU)
. VCC
. GND
. RX
O TX
The following instructions require a connection to the J1 UART header
and are tested for the Archer D7 v1.
For the Archer D7b v1, names should be changed accordingly.
Flash instructions under U-Boot, using UART
------------------------------------------
1. Press "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-squashfs-sysupgrade.bin
erase 0x9f020000 +f90000
cp.b 0x81000000 0x9f020000 0xf90000
reset
Initramfs instructions under U-Boot for testing, using UART
----------------------------------------------------------
1. Press "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-initramfs-kernel.bin
bootm 0x81000000
4. Here you can backup the original firmware and/or flash the sysupgrade openwrt if you want
Restore the original firmware
-----------------------------
0. Backup every partition using the OpenWrt web interface
1. Download the OEM firmware from the TP-Link website
2. Extract the bin file in a folder (eg. Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin)
3. Remove the U-Boot and the Broadcom image part from the file.
Issue the following command:
dd if="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin" of="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod" skip=257 bs=512 count=31872
4. Double check the .mod file size. It must be 16318464 bytes.
5. Flash it using the OpenWrt web interface. Force the update if needed.
WARNING: Remember to NOT keep settings.
5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
Issue below commands in the U-Boot:
tftpboot 0x81000000 Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod
erase 0x9f020000 +f90000
cp.b 0x81000000 0x9f020000 0xf90000
reset
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[cosmetic DTS changes, remove TPLINK_HWREVADD := 0, do not use two
phyXtpt at once, add missing buttons, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer C60 v3 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561 + QCA9886.
It seems to be identical to the v2 revision, except that
it lacks a WPS LED and has different GPIO for amber WAN LED.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 2x button
- UART header on PCB
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
While TFTP works for OpenWrt images, my device didn't accept the
only available official firmware "Archer C60(EU)_V3.0_190115.bin".
In contrast to earlier revisions (v2), the v3 contains the (same)
MAC address twice, once in 0x1fa08 and again in 0x1fb08.
While the partition-table on the device refers to the latter, the
firmware image contains a different partition-table for that region:
name device firmware
factory-boot 0x00000-0x1fb00 0x00000-0x1fa00
default-mac 0x1fb00-0x1fd00 0x1fa00-0x1fc00
pin 0x1fd00-0x1fe00 0x1fc00-0x1fd00
product-info 0x1fe00-0x1ff00 0x1fd00-0x1ff00
device-id 0x1ff00-0x20000 0x1ff00-0x20000
While the MAC address is present twice, other data like the PIN isn't,
so with the partitioning from the firmware image the PIN on the device
would actually be outside of its partition.
Consequently, the patch uses the MAC location from the device (which
is the same as for the v2).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Several devices with tplink-safeloader contain default values (0x0)
for TPLINK_HWID and TPLINK_HWREV in their device definitions.
Move those to common tplink-safeloader definition so they do not
have to be repeated each time.
While at it, set default value for tplink-v1 and tplink-v2 as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds a shared definition Device/tplink-v2 to common-tp-link.mk.
Though currently only one device in ath79 uses it, putting it in
the common file seems more organized. The definitions are based
on the implementation in ramips target, where a lot of devices
is using tplink-v2-* commands already.
The '-V "ver. 2.0"' suffix for Archer D50 v1 can be removed because
it's default in Build/tplink-v2-image anyway.
While at it, add TPLINK_HWREVADD and TPLINK_HVERSION to DEVICE_VARS,
which seems to have been overlooked when adding Archer D50 v1.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This renames Device/tplink-loader-okli to Device/tplink-safeloader-okli
since the latter more accurately describes the combination of
tplink-safeloader and loader-okli use there. The old version might
be confused with other uses of the okli loader.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Based on a script for comparison, this fixes (hopefully) all errors
in SUPPORTED_DEVICES for ar71xx->ath79 upgrade.
Devices where old string is removed as the device does not exist
in ar71xx:
- dlink_dir-859-a1
- tplink_archer-a7-v5
- tplink_cpe510-v3
Devices where string is changed because it did not match the board
name in ar71xx:
- tplink_tl-mr3220-v1
- tplink_tl-mr3420-v1
- tplink_tl-wr2543-v1
- tplink_tl-wr741nd-v4
- tplink_tl-wr841-v7
- ubnt_unifiac-mesh
- ubnt_unifiac-mesh-pro
- ubnt_unifiac-pro
For this device, the correct string could not be found, but we could
not determine the correct one. Thus, the string is removed for now:
- tplink_tl-wr740n-v4
The script for checking this is quite simple (note that newer
entries, i.e. ath79->ath79 upgrade, are displayed as missing):
newpath=target/linux/ath79/image/
oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh
for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do
found="Missing"
grep -q -r "\"$s\"" $oldpath && found="Found"
echo "$s: $found."
done
The errors might be filtered by appending 'grep "Missing"' to the script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device is an LTE router supported in ar71xx so far.
As per original commit, hardware specifications (v1.0 EU):
- SoC: QCA9531
- Flash: Winbond W25Q64FV (8MiB)
- RAM: EtronTech EM6AB160TSE-5G (64MiB)
- Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
- Ethernet: 2NIC (3x100M + 1x100M)
- WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
- Power: DC 12V 1A
Flashing instructions:
You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.
Known issues:
- LTE module does not always come up during boot (showing USB enumeration errors). Similar behavior has been reported at least from one user for ar71xx, too. Turning USB off and on again will serve as a workaround.
- eth0 (LAN) always shows carrier as 1 even if no cable is plugged in (this works "correctly" on ar71xx)
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[several adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Filip Moc <lede@moc6.cz>
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.
Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.
This also moves rootfs_align as this is required as dependency.
Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Christoph Krapp <achterin@googlemail.com>
Both devices are available in 64M and 128M RAM configurations but there
is no visial indication which configuration one might get.
So just to be sure we properly support both configurations switch to
kmod-atk10k-ct-smallbuffers.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
This harmonizes the line wrapping in image Makefile device
definitions, as those are frequently copy-pasted and are a common
subject of review comments. Having the treatment unifying should
reduce the cases where adjustment is necessary afterwards.
Harmonization is achieved by consistently (read "strictly")
applying certain rules:
- Never put more than 80 characters into one line
- Fill lines up (do not break after 40 chars because of ...)
- Use one tab for indent after wrapping by "\"
- Only break after pipe "|" for IMAGE variables
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TL-WDR4300 v1 sold in Israel has a different TPLINK_HWID.
Thanks to Josh4300 for testing on device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch is based on #1689 and adds support for TP-Link Archer
C6 v2 (US) and A6 (US/TW).
The hardware is the same as EU and RU variant, except for GPIOs
(LEDS/Buttons), flash(chip/partitions) and UART being available
on the board.
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q127CS1G (16MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: 115200, 8n1 (header available on board)
Known issues:
- Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range.
Flash instructions:
Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherA6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the
reset button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
Flash partitioning: I've followed #1689 for defining the partition layout
for this patch. The partition named as "tplink" @ 0xfd0000 is marked
as read only as it is where some config for stock firmware are stored.
On stock firmware those stock partitions starts at 0xfd9400 however
I had not been able to make it functional starting on the same address as
on stock fw, so it has been partitioned following #1689 and not the stock
partition layout for this specific partition. Due to that firmware/rootfs
partition lenght is 0xf80000 and not 0xf89400 as stock.
According to the GPL code, the EU/RU/JP variant does have different GPIO pins
assignment to LEDs and buttons, also the flash memory layout is different.
GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz
Signed-off-by: Anderson Vulczak <andi@andi.com.br>
[wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases
to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Ath10k packages were removed from ar71xx in master in commit
34113999ef ("ar71xx: Remove ath10k packages from archer-c7-v1 (fixes
FS#1743)") but ath79 in master and the 19.07 branch still suffer from
the issue.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
In ar71xx, the board name for the TL-WR1043ND v3 is equal to v2:
tl-wr1043nd-v2
Fix SUPPORTED_DEVICES for v3 in ath79 accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for a popular low-cost 2.4GHz N based AP
Specifications:
SoC: Qualcomm Atheros QCA9533 (650MHz)
RAM: 64MB
Storage: 8 MB SPI NOR
Wireless: 2.4GHz N based built into SoC 2x2
Ethernet: 2x 100/10 Mbps, integrated into SoC
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
This also applies some minor changes to the common DTSI:
- use &wmac for label-mac-device, as this one is actually set up in
common DTSI
- move ð0 to parent DTSI
- fix several leading spaces, added/removed newlines
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[DTS style fixes/improvements, updated commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link WBS210 v2 is an outdoor wireless CPE for 2.4 GHz with
two Ethernet ports based on Atheros AR9344
The device is the same as TP-Link CPE220 v2, but with higher TX power (27 dBm
instead of 12 dBm) and two antenna connectors instead of built-in antennas.
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP: 192.168.0.100
Stock device TFTP adress: 192.168.0.254
The TP-Link WBS devices use the same GPIOs as the CPE devices,
except for the link4 LED. For this one, WBS devices use "2", while
CPE devices use "16". (Tested on WBS210 v2)
Signed-off-by: Bernhard Geier <freifunk@geierb.de>
[added comment about GPIO]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- QCA9558 Soc
- 720/800 (CPU/DDR)
- 1x 10/100/1000 Mbps WAN Ethernet
- 4x 10/100/1000 Mbps LAN Ethernet
- 64 MB RAM (DDR2)
- 8 MB FLASH
- QCA9558 2.4 GHz 802.11bgn
- 1x USB 2.0
Flash instruction
WebUI:
Download *-factory.bin image, rename to tp_firmware.bin and upload
it via the firmwary upgrade function of the stock firmware WebUI.
Tftp:
Rename OpenWRT or original firmware to wr1045v2_tp_recovery.bin and
Change your computer ip in 192.168.0.66 and subnet mask in 255.255.255.0.
Router will obtain IP 192.168.0.86 for a few seconds while loading,
when reset button pressed at power On.
Signed-off-by: Rasim Kalimullin <neutrino.vm@gmail.com>
[rebased onto base-files split]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This removes _all_ occurrences of kmod-usb-core from
DEVICE_PACKAGES and similar variables.
This package is pulled as dependency by one of the following
packages in any case:
- kmod-usb-chipidea
- kmod-usb-dwc2
- kmod-usb-ledtrig-usbport
- kmod-usb-ohci
- kmod-usb2
- kmod-usb2-pci
- kmod-usb3
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[remove kmod-usb-core from EnGenius ESR600]
Signed-off-by: David Bauer <mail@david-bauer.net>
This applies alphabetic sorting to devices in image/* files.
For certain cases, this patch deviates from strict sorting, e.g.
to ensure that v10 comes after v9.
While at it, fix an indent and remove some useless empty lines.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add ath79 support for Archer C59v2, previously supported by ar71xx.
TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB
Flash instruction:
- via web UI:
1. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
2. Login to router and open the Advanced tab
3. Navigate to System Tools -> Firmware Upgrade
4. Upload firmware using the Manual Upgrade form
- via TFTP:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Keith Maika <keithm@aoeex.com>
Hardware:
SoC: AR9344
CPU: 560 MHz
Flash: 8 MiB
RAM: 128 MiB
WiFi: Atheros AR9340 2.4GHz 802.11bgn
Atheros AR9300 5GHz 802.11an
Ethernet: AR934X built-in switch, WAN on separate physical interface
USB: 1x 2.0
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
wdr3500v1_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[removed stray newline]
Signed-off-by: David Bauer <mail@david-bauer.net>
This device has not been supported in ar71xx, so there is no need
for an explicit SUPPORTED_DEVICES entry.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This seems to be identical to CPE210 v1 despite having removable
antennas.
Specifications:
* SoC: Qualcomm Atheros AR9344 (560 MHz)
* RAM: 64MB
* Storage: 8 MB
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link CPE510-v1 is an outdoor wireless CPE for 5 GHz with
two Ethernet ports based on Atheros AR9334
Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, 1x PoE-in, 1x PoE-out
- 64 MB of DDR2 RAM
- 8 MB of SPI-NOR Flash
- 2T2R 5 GHz
- 13 dBi built-in antenna
- Power, LAN0, LAN1 green LEDs
- 4x green RSSI LEDs
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Based on the work of Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* SoC: Qualcomm Atheros AR9344 (560 MHz)
* RAM: 64MB
* Storage: 8 MB
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The loader-okli is shared by several TP-Link CPExxx devices, so
give it its own definition to prevent too much code duplication.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer C60 v2 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561 + QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
Flash instruction (under U-Boot, using UART):
tftp 0x81000000 ...-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
reset
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer C60v1 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561+QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 ...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link CPE510-v2/v3 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- Based on the same underlying hardware as the TP-Link CPE510
- Power, LAN, and 4 green LEDs
- 1 10/100Mbps Shielded Ethernet Port (Passive PoE in)
- Built-in 13dBi 2x2 dual-polarized directional MIMO antenna
- Adjustable transmission power from 0 to 23dBm/200mw
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[whitespace fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Increase the Kernel partition to address the issue discussed here
https://forum.openwrt.org/t/cpe610-v1-sysupgrade-bin-missing-too-big/39637/5
Switch Back to the okli Loader to support increased partition size
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [add <> for e-mail]
This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and
DEVICE_VARIANT. All three are merged together to look the same as the
current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as
a *fallback* for devices which weren't upgraded yet.
This is based on the work of @sudhanshu16.
The motivation is to create JSON files based on provided metadata,
needing clear differentiation between vendor, model and revision.
Signed-off-by: Paul Spooren <mail@aparcar.org>
In ath79, identifiers tplink_tl-wdr3600 and tplink_tl-wdr4300 have
been used while most other TP-Link devices include the revision.
Although there actually is only one major revision of these
devices, they bear the revision on their bottom (v1.x). TP-Link
also refers to the devices as V1 on its web page.
This patch thus adds -v1 to both so it is more consistent
with other devices and with what you would expect from reading
the on-device sticker and the support pages.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link CPE610-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- Based on the same underlying hardware as the TP-Link CPE510
- Power, LAN, WLAN5G green LEDs
- 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
The TP-Link Archer C25 is a low-cost dual-band router.
Specification:
- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet
Some LEDs are controlled by an additional 74HC595 chip, but not
all of them as e.g. for the C59.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer D50 v1 is a dual-band AC1200 router + modem.
The router section is based on Qualcomm/Atheros QCA9531 + QCA9882.
The "DSL" section is based on BCM6318 but it's currently not supported.
Internally eth0 is connected to the Broadcom CPU.
Router section - Specification:
CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB)
RAM: 64 MB (DDR2)
Flash: 8 MB (SPI NOR)
Wifi 2.4GHz: QCA9531 2T2R
Wifi 5GHz: QCA9982 2T2R
4x 10/100 Mbps Ethernet
8x LED, 3x button
UART header on PCB
Known issues:
DSL not working (eth0) (WIP)
UART connection
---------------
J2 HEADER (Qualcomm CPU)
. TX
. RX
. GND
O VCC
J16 HEADER (Broadcom CPU)
O VCC
. GND
. RX
. TX
The following instructions require a connection to the J2 UART header.
Flash instruction under U-Boot, using UART
------------------------------------------
1. Press any key to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Initramfs instruction under U-Boot for testing, using UART
----------------------------------------------------------
1. Press any key to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin
bootm 0x81000000
Restore the original firmware
-----------------------------
0. Backup every partition using the OpenWrt web interface
1. Download the OEM firmware from the TP-Link website
2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin)
3. Remove the U-Boot and the Broadcom image part from the file.
Issue the following command:
dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616
4. Double check the .mod file size. It must be 7995392 bytes.
5. Flash it using the OpenWrt web interface. Force the update if needed.
WARNING: Remember to NOT keep settings.
5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
Issue below commands in the U-Boot:
tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed
default-state = "off", it's already the default, added pcie node,
fixed typo]
Specifications:
- QCA9563 at 775 MHz
- 64 MB RAM Zentel A3R12E40CBF-8E
- 16 MB flash Winbond W25Q128FVSG
- 3 (non-detachable) Antennas / 450 Mbit
- 1x/4x WAN/LAN Gbps Ethernet (QCA8337)
- reset and Wi-Fi buttons
TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4,
except that the USB port has been removed and there is no longer a
removable antenna option. It also has different partitioning scheme.
The software is more in line with the Archer series in that it uses a
nested bootloader scheme.
(This has been adapted from the OpenWrt Wiki page)
<https://openwrt.org/toh/tp-link/tl-wr1043nd>
Installation on HW rev.5:
Factory firmware can be installed via the WEB interface.
Alternatively, it is also possible to use a TFTP server
for recovery purposes:
- Rename OpenWRT or original firmware to WR1043v5_tp_recovery.bin
- Set static IP of your PC to *192.168.0.66*
- Router will obtain IP 192.168.0.86 for a few seconds while
loading, when reset button pressed at power On.
And finally, there's always u-boot access through the UART.
For information visit the wiki.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[reworked commit message]
This adds support for the TP-Link WR842N v3 which is already supported on ar71xx
target (0b45bec22c).
Specification:
* SoC: QCA9533 ver 2 rev 0
* 16 MB Flash (gd25q128)
* 64 MB RAM
* 1 WAN 10/100 MBit/s (blue connector)
* 4 LAN 10/100 MBit/s (AR8229; 4 ports; yellow connectors)
* Atheros AR9531 (2,4GHz, two fixed antennas)
* USB
* Reset / WPS button
* WiFi button (rf kill)
* 8 green leds; 1 red/green led
* serial console (115200 8N1, according to the OpenWrt-wiki some soldering is needed)
Installation:
* flash via vendor WebUI (the filename must not exceed certain length)
* sysupgrade from installed OpenWrt (also ar71xx)
Thanks to Holger Drefs for providing the hardware
Tested-by: @kofec (github)
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
