Due to upstream change in U-boot the binaries were renamed [1].
[1] 87ac4b4b4c
Fixes: 2f83369e3e ("uboot-mvebu: update to version 2023.01")
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Testing target changes was only set for push events. Enable this also
for pull request events to enable testing pr making specific target
changes.
Fixes: 57a02cbbff ("CI: kernel: test each target with additional changes than target/linux")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
ZyXEL NBG7815 is a premium 802.11ax "tri"-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 1 GB 2x Nanya NT5CC256M16ER-EK
* Storage:
* 8MB serial flash Winbond W25Q64DW
* 4GB eMMC flash Kingston EMMC04G-M627
* Ethernet:
* 4x1G RJ45 ports (QCA8074A) with 1x status LED per port
* 1x2.5G RJ45 port (QCA8081) with 1x status LED
* 1x10G RJ45 port (AQR113C) with 1x status LED
* Switch: Qualcomm Atheros QCA8075
* WLAN:
* 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate
* 2x 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
* Bluetooth CSR8811 using HSUART, currently unsupported
* USB: 1x USB3.0 Type-A port
* LED-s currently not supported:
* White
* Dark Blu
* Amber
* Purple
* Purple and dark blue
* Red
* Buttons:
* 1x Soft reset
* Power: 12V DC Jack
Installation instructions:
* Disconnect WAN
* Reset device to factory defaults by pushing reset button 15 sec,
LEDs should lit orange color.
* After 5-10 minutes, when the LEDs turn constant dark blue,
put your LAN cable and connect at address 192.168.123.1 by telnet on port 23
* Login with
NBG7815 login: root
password: nbg7815@2019
* cd /tmp/ApplicationData
* wget -O openwrt-ipq807x-generic-zyxel_nbg7815-squashfs-sysupgrade.bin http://...
* wget https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh
* run flash_to_openwrt.sh
If you can't use wget, you can transfer the files via nc.
See https://openwrt.org/inbox/toh/zyxel/nbg7815_armor_g5 for installation details.
Bluetooth usage:
* you need at least package bluez-utils, recommended bluez-daemon
* run following commands to enable and start
hciattach /dev/ttyMSM1 bcsp
hciconfig hci0 up
Many thanks to itorK for his work on this device:
https://github.com/itorK/openwrt/tree/nbg7815
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: André Valentin <avalentin@marcant.net>
Enabling kernel symbol CONFIG_NVMEM_U_BOOT_ENV allows to use u-boot
environement variable ethaddr with nvmen. That way it is possible to assign
the MAC address to the ethernet device driver.
Example of usage in dts:
....
partition@600000 {
compatible = "u-boot,env";
label = "0:appsblenv";
reg = <0x600000 0x10000>;
macaddr_lan: ethaddr {
};
};
....
&dp5 {
status = "okay";
phy-handle = <&qca8081>;
label = "wan";
nvmem-cells = <&macaddr_lan>;
nvmem-cell-names = "mac-address-ascii";
mac-address-increment = <1>;
};
This is needed for Zyxel NBG7815.
Signed-off-by: André Valentin <avalentin@marcant.net>
To download a package the LLVM bins are not strictly needed.
Currently with an example run of make package/bridger/download V=s, the
build fail with
make[2]: Entering directory '/home/ansuel/openwrt-ansuel/openwrt/package/network/services/bridger'
bash: line 1: /home/ansuel/openwrt-ansuel/openwrt/staging_dir/host/llvm-bpf/bin/clang: No such file or directory
bash: line 1: [: : integer expression expected
/home/ansuel/openwrt-ansuel/openwrt/include/bpf.mk:71: *** ERROR: LLVM/clang version too old. Minimum required: 12, found: . Stop.
make[2]: Leaving directory '/home/ansuel/openwrt-ansuel/openwrt/package/network/services/bridger'
time: package/network/services/bridger/download#0.04#0.00#0.06
ERROR: package/network/services/bridger failed to build.
This is wrong since it may be needed to download the required packages
first and then compile them later.
Fix this by ignoring the LLVM bin check on non compile steps.
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Patch the mbedtls source instead of modifying the compile-targets
in the prepare buildstep within OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
Move defines from header to defconfig
The package build and the Buildbot hang in 'make syncconfig' for
u-boot-ravpower_rp-wd009 because CONFIG_SYS_MIPS_TIMER_FREQ is not in
the .config, causing a console prompt. Also moved two other defines in
defconfig causing duplicate definition warnings.
Fixes: 3d5c5427e1 ("uboot-mediatek: update to U-Boot 2023.01")
Signed-off-by: Jo Deisenhofer <jo.deisenhofer@gmail.com>
The configured u_env partition for the Linksys WHW03 V2 was not correct.
It should have been set to mtd6.
This fix allow to flash the OEM firmware from OpenWRT and to change the
boot partition using fw_setenv.
Fixes: 9e4ede8344 ("ipq40xx: add support for Linksys WHW03 V2")
Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
In the version 2023.01, the U-boot image was renamed because of the
upstream change [1]
[1] 87ac4b4b4c
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
libdeflate decompresses much faster than gzip.
Example:
~/d/openwrt> time gzip -dc dl/cmake-3.25.1.tar.gz > /dev/null
________________________________________________________
Executed in 1.01 secs fish external
usr time 912.61 millis 1.67 millis 910.94 millis
sys time 32.21 millis 0.25 millis 31.96 millis
~/d/openwrt> time libdeflate-gzip -dc dl/cmake-3.25.1.tar.gz > /dev/null
________________________________________________________
Executed in 523.04 millis fish external
usr time 415.48 millis 1.07 millis 414.41 millis
sys time 107.74 millis 0.15 millis 107.59 millis
~/d/openwrt> time gzip -dc dl/tessdata-4.1.0.tar.gz > /dev/null
________________________________________________________
Executed in 8.99 secs fish external
usr time 8.90 secs 530.00 micros 8.90 secs
sys time 0.07 secs 63.00 micros 0.07 secs
~/d/openwrt> time libdeflate-gzip -dc dl/tessdata-4.1.0.tar.gz > /dev/null
________________________________________________________
Executed in 2.74 secs fish external
usr time 2.38 secs 537.00 micros 2.38 secs
sys time 0.35 secs 66.00 micros 0.35 secs
Place libdeflate into tools-core as it is needed to decompress other
archives.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
CMake depends on (libdeflate-)gunzip, libdeflate depends on Cmake, so we
can't win.
Luckily libdeflate is _very_ easy to build, without any build system, so
lets just manually compile it and be done with it.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Like with commit ae614fb397 ("tools: Improve diffability/maintainability")
we also want tools-core to be easy to maintain. While a smaller target,
it's still usefull and makes things nice and consistent.
To avoid duplicating any tools in the comment, simplify the comment
instead.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Requires: tools/lz4, tools/lzop
complete the wiring so that these options work:
* `CONFIG_KERNEL_INITRAMFS_COMPRESSION_LZO`
* `CONFIG_KERNEL_INITRAMFS_COMPRESSION_LZ4`
Signed-off-by: Tony Butler <spudz76@gmail.com>
[remove blocking dependencies for separate ramdisk, fix lzop options]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Depends: `tools/liblzo`
`lzop` is the standard executable for LZO compression
the initramfs generator offers the LZO option but there was no
executable to support it actually working
Signed-off-by: Tony Butler <spudz76@gmail.com>
prerequisite of upcoming `tools/lzop` addition, and subsequent initramfs
and squashfs cleanups
same as `packages/lzo` modified to be a HOST/tools type build,
and should always be the same version and sources when either one is
bumped
because this (and `packages/lzo`) only provide liblzo and no
executables, use the clearer name `tools/liblzo`
Signed-off-by: Tony Butler <spudz76@gmail.com>
same as `packages/liblz4` modified to be a HOST/tools type build with
unified liblz4 (this is also the dev package for liblz4)
the image initramfs generator offers the LZ4 option but there was no
executable to support it actually working
Signed-off-by: Tony Butler <spudz76@gmail.com>
Set up MAC, LED, settings and default packages for DSL usage, similar
to the lantiq target.
Due to licensing uncertainty, we do not include the firmware files for the
DSL drivers. To have a working DSL setup, follow the instructions below.
Download the firmware files locally:
mkdir -p files/lib/firmware/09a9
wget -P files/lib/firmware/09a9 https://gitlab.com/prpl-foundation/intel/vrx518_aca_fw/-/raw/ugw-8.5.2/platform/xrx500/aca_fw.bin
wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/vrx518_ppe_fw/-/raw/ugw_8.5.2.10/platform/xrx500/ppe_fw.bin
wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/dsl_vr11_firmware_xdsl/-/raw/ugw-8.5.2/xcpe_8D1507_8D0901.bin
ln -s xcpe_8D1507_8D0901.bin files/lib/firmware/vdsl.bin
For people building their own images:
Run the above commands in the root of your local OpenWrt clone,
and the firmware files will be part of the resulting images.
For people downloading images:
Copy the firmware files onto the router once it's booted up:
scp -O -r files/lib/firmware root@fritz:/lib
Reboot the device afterwards.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[cleaned up]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[set up LED]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
This is needed by the mei driver to be able to download the firmware.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
This uses version 4.23.1 of the dsl_cpe_control package from the Intel
UGW 8.5.2.10 for the VRX518.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[rebased]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update to 4.23.1, added Jan's vector mac patch, fix warnings,
switch to tag tarball]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[add missing nLine in autoboot script, fix disconnect on termination,
remove unneeded VR9 leftovers in init script]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
This uses version 4.23.1 of the drv_dsl_cpe_api package from the Intel
UGW 8.5.2.10 for the VRX518.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[rebased and updated for kernel 5.10]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update to 4.23.1, switch to tag tarball, update patches]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[added fix for elapsed time and upstream MINEFTR]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
This uses version 1.11.1 of the drv_mei_cpe package from the Intel UGW
8.5.2.10 for the VRX518.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[updated for kernel 5.10]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update to 1.11.1, switch to tag tarball, update patches]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[update for kernel 5.15]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
This driver version is also included in Intel UGW 8.5.2.10.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[updated for kernel 5.10]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update to 1.5.12.4, switch to tag tarball]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[add working software data path]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Similar to the lantiq platform, these are required for DSL support.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[switch to kernel 5.10 and 5.15]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update patches based on UGW 8.5.2.10, remove 5.10 support]
Signed-off-by: Andre Heider <a.heider@gmail.com>
This driver was picked from the Intel UGW 8.5.2.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[updated for kernel 5.10]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update to 8.5.2]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[fix masking interrupts and add locking]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
04d7570 jail: fs: don't overwrite existing mount target
6b9629b jail: don't assume positive return value of creat
190f13a init: attempt to mount efivarfs
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A previous attempt to simplify things went wrong and now sysupgrade
is broken on this device. Fix that.
Fixes: de94587e70 ("mediatek: filogic: don't rely on image preset in flash or sysupgrade")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A previous attempt to simplify things went wrong and now sysupgrade
is broken on this device. Fix that.
Fixes: d640cbac0e ("mediatek: mt7622: don't rely on existing image for sysupgrade")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patch that adds support for hw flow-offloading counters on newer
MediaTek SoCs tries to prints acct->packets and acct->bytes in debugfs,
without checking that acct isn't null. This causes a kernel panic when
trying to read /sys/kernel/debug/ppe0/entries on older MediaTek SoCs.
Fix this by adding a check for acct.
Fixes: openwrt#11756
Fixes: 9721a42a27 ("kernel: support hw flow-offloading counters on newer MediaTek SoCs")
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It appears that only a few users are using the archs38 SoC. The most
active user of the target has already approved the testing kernel and
so it is very unlikely bugs will be reported in the near future.
Therefore, the target should be directly bumped to 5.15.
Signed-off-by: Nick Hainke <vincent@systemli.org>
This fixes spurious build-errors on OpenWrt, where the AM_ICONV macro
is undefined while invoking autoconfig. Later in the build, the ICONV
LDOPTIONS are set to @LIBICONV@, failing the build.
Signed-off-by: David Bauer <mail@david-bauer.net>
Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports.
Specifications:
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 1024MB of DDR3
• Storage: 256MB Nand
• Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
• WLAN:
2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate
5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
• 1x USB 3.0
• 1 gpio-controlled dual color led (blue/red)
• Buttons: 1x soft reset / 1x WPS
• Power: 12V DC jack
A poulated serial header is onboard (J1004)
the connector size is a 4-pin 2.0 mm JST PH.
RX/TX is working, u-boot bootwait is active, secure boot is enabled.
Notes:
- Serial is completely deactivated in the stock firmware image.
- This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
- Installation can be done by serial connection or
SSH access on OEM firmware
Installation Instructions:
Most part of the installation is performed from an initramfs image
running OpenWrt, and there are two options to boot it.
Boot initramfs option 1: Using serial connection (3.3V)
1. Stop auto boot to get to U-boot shell
2. Transfer initramfs image to device
(openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb)
Tested using TFTP and a FAT-formatted USB flash drive.
3. Boot the initramfs image
# bootm
Boot initramfs option 2: From SSH access on OEM firmware
1. Copy the initramfs image to a FAT-formatted flash drive
(tested on single-partition drive) and connect it to device USB port.
2. Change boot command so it loads the initramfs image on next boot
Fallback to OEM firmware is provided.
# fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq'
3. Reboot the device to boot the initramfs
# reboot
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Check MTD partition table.
rootfs and rootfs_1 should be mtd18 and mtd20
depending on current OEM slot.
# cat /proc/mtd
4. Do a ubiformat to both rootfs partitions:
# ubiformat /dev/mtd18 -y -f /path_to/factory_image
# ubiformat /dev/mtd20 -y -f /path_to/factory_image
5. Set U-boot env variable: mtdids
# fw_setenv mtdids 'nand0=nand0'
6. Get offset of mtd18 to determine current OEM slot
- If current OEM slot is 1, offset is 16777216 (0x1000000)
- If current OEM slot is 2, offset is 127926272 (0x7a00000)
# cat /sys/class/mtd/mtd18/offset
7. Set U-boot env variable: mtdparts
If current OEM slot is 1, run:
# fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)'
If current OEM slot is 2, run:
# fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)'
8. Set U-boot env variable: bootcmd
# fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0'
9. Reboot the device
# reboot
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
The Edgecore EAP102 is a wall/ceiling mountable AP. The AP can be
powered by either PoE or AC adapter.
Device info:
- IPQ8071-A SoC
- 1GiB RAM
- 256MiB NAND flash
- 32MiB SPI NOR
- 2 Ethernet ports
- 1 Console port
- 2GHz/5GHz AX WLAN
- 2 USB 2.0 ports
Install instructions:
Prerequistes - TFTP server, preferrably within 192.168.1.0/24
Console cable plugged in (115200 8N1 no flow control)
1. Power on device and interrupt u-boot to obtain u-boot CLI
2. set serverip to IP address of the TFTP server:
`setenv serverip 192.168.1.250`
3. Download image from TFTP server:
`tftpboot 0x44000000 openwrt-ipq807x-generic-edgecore_eap102-squashfs-nand-factory.ubi`
4. Flash ubi image to both partitions and reset:
`sf probe
imxtract 0x44000000 ubi
nand device 0
nand erase 0x0 0x3400000
nand erase 0x3c00000 0x3400000
nand write $fileaddr 0x0 $filesize
nand write $fileaddr 0x3c00000 $filesize
reset`
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet:
* 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* 1x2.5G RJ45 port (QCA8081) with 1x status LED
* WLAN:
* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
* 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate
* 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate
* 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate
* USB: 1x USB3.0 Type-A port
* LED-s:
* System (Blue and Yellow)
* Network (Blue and Yellow)
* RGB light bar on top in X shape
* Buttons:
* 1x Power switch
* 1x Soft reset
* 1x Mesh button
* Power: 12V DC Jack
Installation instructions:
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd21 and mtd22 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
6. Reboot the device by:
reboot
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: Robert Marko <robimarko@gmail.com>
QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports.
Specifications:
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 1024MB of DDR3
• Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR
(contains art and u-boot-env)
• Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C)
• WLAN:
2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate
5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate
• LEDs:
7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs
• Buttons: 1x soft reset / 1x WPS
• Power: 12V DC jack
A poulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, hold WPS button til the second beep
(yes the router has a buzzer)
SSH is available on port 22200, login with user admin and
password "mac address of the router".
Installation Instructions:
• obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial)
• stop auto boot
• setenv serverip 192.168.10.1
• setenv ipaddr 192.168.10.10
• tftpboot the initramfs image
(openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb)
• bootm
• make sure that current_entry is set to "0":
"fw_printenv -n current_entry" should be print "0". If not,
do "fw_setenv current_entry 0"
• copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
to the device to /tmp folder
• sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4)
• reboot
Note: this leaves the second kernel / rootfs parition untouched. So if you want
to go back to stock, stop u-boot autoboot, "setenv current_entry 1" ,
"saveenv", "bootipq".
Stock firmware should start from the second partition.
Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt
in the first partitions
Make 10G Aquantia phy's work:
The aquantia phy's need a firmware to work. This can either be loaded
in linux with a userspace tool or in u-boot.
I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is
aq_load_fw available in u-boot. But first the right firmware needs to write
to the 0:ETHPHYFW mtd partition (it is empty on my device)
Grab the ethphy firmware image from:
https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn
and scp that to openwrt.
Check the 0:ETHPHYFW partition number:
cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10.
Backup the 0:ETHPHYFW partition:
dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place.
Write the new firmware image to the 0:ETHPHYFW partition:
"mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10".
Reboot to u-boot.
Check if aq_load_fw is working:
"aq_load_fw 0", that checks the firmware and if successfull,
loads iram and dram to one of the aquantia phy's.
If that worked, add the aq_load_fw to the bootcmd:
setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq"
"saveenv"
"reset"
Board reboots and the firmware load to both phy's should start and
then openwrt boots.
Check if the 10G ports work.
Note: lan port labeled "10G-2" is configured as WAN port as per default.
All other port are in the br-lan. This can be changed in the network config.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Edimax CAX1800 is a 802.11 ax dual-band AP
with PoE. AP can be ceiling or wall mount.
Specifications:
• CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz
• RAM: 512MB of DDR3
• Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WLAN:
2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
3 x GPIO-controlled System-LEDs
(form one virtual RGB System-LED)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An unpopulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, but it drops only
to a limited shell .
Installation Instructions:
black_small_square obtain serial access
black_small_square stop auto boot
black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot)
black_small_square bootm
black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi
to the device
black_small_square write the image to the NAND:
black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0)
black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs-
nand-factory.ubi
black_small_square reboot
Note: Device is not using dual partitioning (NAND contains other partitions
with different manufacture data etc.)
Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Redmi AX6 is a budget 802.11ax dual-band router/AP
Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 128MB NAND
* Ethernet: 4x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LEDs:
* System (Blue/Yellow)
* Network (Blue/Yellow)
*Buttons: 1x soft reset
*Power: 12V DC jack
Installation instructions:
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
6. Reboot the device by:
reboot
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: Zhijun You <hujy652@gmail.com>
Xiaomi AX3600 is a budget 802.11ax dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* WLAN:
* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
* System (Blue and Yellow)
* IoT (Blue)
* Network (Blue and Yellow)
* Buttons: 1x Soft reset
* Power: 12V DC Jack
Installation instructions:
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
6. Reboot the device by:
reboot
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Include NSS DP and SSDK (Pulled as dependency) by default on ipq807x to
provide wired networking to the target.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Qualcomm NSS-DP is as its name says Qualcomms ethernet driver for the NSS
subsystem (Networking subsystem) built-into various Qualcomm SoCs.
It has 2 modes of operation:
* Without NSS FW and rest of code required for offloading
This is the one that we will use as the amount of kernel patching required
for NSS offloading and the fact that its not upstreamable at all makes it
unusable for us.
Driver in this mode is rather basic, it currently only offers NAPI GRO
(Added by us as part of the fixup) and basically relies on the powerfull
CPU to get good throughput.
* With NSS FW and rest of code required for offloading
In this mode, driver just registers the interfaces and hooks them into
NSS-ECM to allow offloading.
This mode is not viable for use in OpenWrt due to reasons already described
above.
This driver is required for ipq807x to have wired networking until a better
one is available, so lets add the fixed-up version for 5.15 for now.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Qualcomm SSDK is driver for Qualcomm Atheros switches and PHY-s.
It is quite complicated and used by rest of the Qualcomm SDK stack for
anything switch or PHY related.
It is required for IPQ807x support as currently, there is no better driver
for the built-in switch or UNIPHY.
So, lets add the fixed-up version that supports kernel 5.15 for use on
ipq807x target until a better driver is available.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is the follow up to the PCI support commit now providing support for
AHB variant as well, though currently only for ipq807x as that is only
OpenWrt supported SoC ath11k supports as well.
Currently, we are disabling coldboot calibration on ipq807x as it does not
work, there is a remoteproc bug that makes it come late out of reset so
disable coldboot until that is fixed.
Also, as ath11k is quite memory hungry, we are introducing a config option
to use the limits for 512MB of RAM, similar to what QCA does downstream but
in way simpler and cleaner way so that 512MB save some RAM.
512MB profile is also set as the default for now.
Signed-off-by: Robert Marko <robimarko@gmail.com>
