Modernize U-Boot to provide a better reference:
* store fip image in UBI now that TF-A supports that
* switch from uImage.FIT partition parser to new fitblk
virtual firmware block driver (root=/dev/fit0)
* automatically set root device according to boot_mode register
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add environment settings for the BananaPi BPI-R4 router board which
can boot from (and store its bootloader environment on) micro SD card,
SPI-NAND and eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use function instead of duplicating the env settings on UBI for
OpenWrt-built U-Boot over and over.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
SOC: MediaTek MT7988A (4x Cortex-A73)
RAM: 4 GiB DDR4
Flash: 128 MiB Winbond SPI-NAND
MMC: 8 GiB eMMC *or* microSD (cannot be used both)
ETH: 4x 1GE (1x WAN, 3x LAN)
2x SFP+ (10G, 5G, 2.5G, 1G)
USB: on-board USB 3.2 4-port hub
1x USB 3.2 port (type A connector)
1x M.2 for 4G/5G modem
2x mPCIe for additional modems
WiFi: optional MediaTek MT7996 Wi-Fi 7 module
(using 2x PCIe gen3 x2 on the mPCIe slots and 12V power)
Installation
------------
1. Decompress and write the sdcard image to a micro SD card and use that
to boot the R4 (both dip switches in upper position).
2. Use the bootloader menu accessible via the serial console to install
to SPI-NAND.
3. Switch to boot from SPI-NAND and install to eMMC.
Known issues
------------
- The RST button is hard-wired to the SoC reset and can't be read
from software. This can be changed by modifying the board (ie.
moving a 0-ohm resistor). However, in order to maintain compatibility
with the board as it comes from factory the button isn't used by
OpenWrt and the WPS button is used as factory/reset button instead.
- various small things still need to be fixed in DT
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rebase local patches on top of quarterly timed release, allowing to
drop numerous patches which have been accepted upstream since the
release of U-Boot 2023.07.02.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If nodes /chosen/rootdisk-${bootdevice} exists, set /chosen/rootdisk
phandle according to boot device selected by the bootstrap pins.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When erasing large amounts of blocks at once this can take a long
time on slow cards. Instead of a fixed timeout, wait longer if more
blocks are being erased.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add basic U-Boot drop-in replacement compatible with the flash layout
of the vendor loader of the Zbtlink WG3526 (16M) MT7621 router board.
The idea here is a to have a reference build of uboot-mediatek also for
a simple MIPS boards more popular than MT7621 RFB.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patch from MediaTek SDK which allows using the third
PCIe host controller of the MT7988 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add UART pinctrl group for using only pins 80 and 81 for uart1.
This is needed on the BPi-R4 as RTS/CTS signals are used for other
on-board functions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace previous patch adding paths and SerDes modes with patch series
pending upstream adding dedicated drivers for XFI T-PHY and USXGMII PCS,
extends LynxI PCS to be a standalone platform driver and as a consequence
makes much less changes to the actual Ethernet driver mtk_eth_soc.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport almost 50 commits from upstream Linux to improve thermal
drivers for MediaTek SoCs and add new LVTS driver for MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Let's pick a bunch of useful phylink changes which allow us to keep
drivers in sync with mainline Linux.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add minimalistic tool to allow releasing /dev/fit* devices which is
needed on sysupgrade when using the fitblk driver.
The package is hidden in menuconfig, it should only be selected by
adding it to the default package selection of boards using it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add 'fitblk' driver to replace the rejected/deprecated uImage.FIT
partition parser.
To use the new driver, add phandle /chosen/rootdisk and point it to
the MTD partition, UBI volume or block device holding the uImage.FIT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Similar to supporting nvmem-layouts on MTD devices, also allow referencing
UBI and MMC devices in DT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In order to allow gradually migrating the boards currently using the
uImage.FIT partition (deprecated/rejected) parser to the new fitblk
driver, skip the partition parser code in case the new fitblk driver
(which serves the same purpose) is used.
As an indicator for the use of the new fitblk driver, check if the
/chosen/rootdisk property is present in the Device Tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The partition parser approach has been rejected upstream, it will be
replaced by a small block driver which is the solution suggestion by
upstream maintainers.
As the partition parser has only been used by the mediatek target, as
a first step, move it there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport two commits from Linux 6.3 wiring up device node parents of
ubi devices (pointing to their MTD parent) as well as ubiblock devices
(poiting to their parent UBI volume).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make use of recently added UBI support in MediaTek's ARM
TrustedFirmware-A on new MT7988 SoC.
Load fip from static UBI volume instead of fixed offset on SPIM-NAND
and SNFI.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hide arm-trusted-firmware-mediatek packages from interactive config.
Exposing them only causes confusion and needed variants are anyway
selected as dependencies by uboot-mediatek packages.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Convert qca807x PHY to new implementation like for other devices.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Now that Malibu (QCA807x) PHY-s use an upstream driver we dont need support
for defining address of the first PHY in the package so drop the patch.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that Malibu (QCA807x) PHY is using the upstream driver, we dont need
support to define address of the first PHY in package, so remove the
malibu_first_phy_addr DTS property.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that QCA807x interface mode check was upstreamed, use the upstreamed
version and mark it as such.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Disable compilation of separate tests as it causes
a build error when combined with ccache
Fixes: 4a3f430d72 ("tools/expat: update to 2.6.0")
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Use order described as preferred in DTS Coding Style. Mostly just move
"compatible", "reg", "ranges" and "status" properties.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
PoE devices in the realtek target have the possibility to add PSE info
to the board description via 02_network. Make this available for all
targets, by moving the uci_set_poe() function to the globally available
uci-default.sh script.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
uci_set_poe() now performs two duties: filtering the list of device
ports to exclude non-PoE ports, and generating the PoE related device
config.
Extract the port filtering to an external function, which is made a bit
more readable by the use of 'sort -V [-r] | uniq -u' to filter duplicate
entries out of a (reverse) version sorted list.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The ZyXEL XGS1250-12 has a chassis fan. The fan is positioned perfectly to
provide additional cooling to the Aquantia NBase-T phys. Testing has shown
that the phys can reach temperatures upwards of 72 degrees Celsius quite
easily at about 20 degrees Celsius ambient.
Support the chassis fan to give the phys a bit of extra cooling.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
This reverts commit 131e41614d.
Sadly it makes menuconfig fail with
tmp/.config-package.in:171: glob failed: No files found "feeds/base/utils/busybox/Config.in"
make: *** [/usr/src/openwrt/include/toplevel.mk:136: menuconfig] Error 1
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
