Commit Graph

21044 Commits

Author SHA1 Message Date
Tobias Schramm
d78e229903 ath79: Add support for Ubiquiti NanoBeam AC
The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware
almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation
AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi
indicators, the fifth LED is used as an ethernet link/activity indicator.

CPU:   Atheros AR9342 SoC
RAM:   64 MB DDR2
Flash: 16 MB NOR SPI
WLAN:  QCA988X
Ports: 1x GbE

Flashing procedure is identical to the NanoStation AC loco and can be performed
either via serial or the factory firmware upgrade.

Serial flashing:

1. Connect to serial header on device (8N1 115200)
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy

Flashing through factory firmware:

1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version.
2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot

Thanks to @cybermaus for testing!

Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com>
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2019-03-22 00:40:29 +01:00
Xavier Douville
5ac974f214 ar71xx: Add support for Mikrotik RB SXT 2nD r3
The Mikrotik RouterBOARD SXT 2nD r3 is an outdoor WiFi AP / CPE
with a single 2.4 GHz radio and a 100 Mbps Ethernet port.
The device similar to the SXT 2nD r2, but it has SPI NOR flash instead
of NAND flash.

Hardware
--------
CPU:   Atheros AR9344 (600 MHz)
RAM:   64 MiB
FLASH: 16 MiB SPI NOR W25Q128
ETH:   1x 100 Mbps Atheros AG71xx
WiFi: 2T2R 802.11b/g/n (ath9k)
Power: Passive PoE 8-30 V

Installation instructions:

1. Boot openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf using a
   DHCP+TFTP server.
2. Erase the "firmware" partition using the mtd command. This should
   no longer be required once this patch is merged.
3. Use sysupgrade to install to flash. The file
   openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin
   should be used.

Signed-off-by: Xavier Douville <github@douville.org>
2019-03-22 00:40:29 +01:00
Aubrey McIntosh, PhD
34113999ef ar71xx: Remove ath10k packages from archer-c7-v1 (fixes FS#1743)
ath10k_pci driver crashes once loaded and causes boot loops on this
device as 5GHz radio QCA9880-AR1A shipped with this router is broken.
It's not possible to fix this problem in software, miniPCIe radio has to
be replaced.

We could've probably fixed crashing of the ath10k driver by reverting
following upstream commit:

 commit 1a7fecb766c83dace747f42b25bbb544b00a0163
 Author: Michal Kazior <michal.kazior@tieto.com>
 Date:   Sat Jan 24 12:14:48 2015 +0200

    ath10k: reset chip before reading chip_id in probe

but it's not worth the effort as it wouldn't make that 5GHz radio usable
anyway. So it seems more convenient to just remove the crashing driver
and provide bootable images, as I believe, that a router that is working
but degraded is better than a router that will not work.

For details please see discussions in PR[1] and in FS#1743[2].

1. https://github.com/openwrt/openwrt/pull/1349
2. https://bugs.openwrt.org/index.php?do=details&task_id=1743

Signed-off-by: Aubrey McIntosh, PhD <aubrey.mcintosh@utexas.edu>
[subject and commit message tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-21 02:04:57 +01:00
Andreas Ziegler
78b9d57882 ath79: GL.iNet AR300M-nand/nor: correct LAN LED
The port labled as "LAN" is eth1.
That's different from the -lite variant,
where the only existing port eth0 is used as LAN

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
2019-03-21 00:57:54 +01:00
Adrian Schmutzler
4269914187 ramips: Speed up eeprom read/write
Reading and writing to and from flash storage is slowed down
enormously by some functions which use a block size of 1.

This patch reworks the extraction scripts to be much faster and
efficient by reading and writing in possibly one big block.

This is based on the initial commit a69e101 for ipq40xx by
Christian Lamparter <chunkeey@gmail.com>.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Rosen Penev <rosenp@gmail.com>
2019-03-21 00:57:54 +01:00
Ozgur Can Leonard
201d3d1a82 ramips: Xiaomi MIR3G: detect board name from DTS
- Former "mir3g" board name becomes "xiaomi,mir3g".
- Reorder some entries to maintain alphabetical order.
- Change DTS so status LEDs (yellow/red/blue) mimic
  Xiaomi stock firmware: (Section Indicator)
<http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf>
<http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf>
|Yellow: Update (LED flickering), the launch of the system (steady light);
|Blue: during normal operation (steady light);
|Red: Safe mode (display flicker), system failure (steady light);

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
[Added link to similar Router 3 model]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-21 00:57:54 +01:00
Steve Glennon
dc4f6b896f ipq40xx: add support for EnGenius ENS620EXT
Hardware
--------
CPU:   Qualcomm IPQ4018
RAM:   256M
FLASH: 32M SPI NOR W25Q256
ETH:   QCA8075
WiFi2: IPQ4018 2T2R 2SS b/g/n
WiFi5: IPQ4018 2T2R 2SS n/ac
LED:    - Power amber
        - LAN1(PoE) green
        - LAN2 green
        - Wi-Fi 2.4GHz green
        - Wi-Fi 5GHz green
BTN:    - WPS
UART:  115200n8 3.3V J1
       VCC(1) - GND(2) - TX(3) - RX(4)

Added basic support to get the device up and running for a sysupgrade
image only.
There is currently no way back to factory firmware, so this is a one-way
street to OpenWRT.
Install from factory condition is convoluted, and may brick your device:
1) Enable SSH and disable the CLI on the factory device from the web user
   interface (Management->Advanced)
2) Reboot the device
3) Override the default, limited SSH shell:
   a) Get into the ssh shell:
      ssh admin@192.168.1.1 /bin/sh --login
   b) Change the dropbear script to disable the limited shell. At the
      empty command prompt type:
        sed -i '/login_ssh/s/^/#/g’ dropbear
        /etc/init.d/dropbear restart
        exit
4) ssh in to a (now-) normal OpenWRT SSH session
5) Flash your built image
   a) scp openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
      admin@192.168.1.1:/tmp/
   b) ssh admin@192.168.1.1
   c) sysupgrade -n
      /tmp/openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
6) After flash completes (it may say "Upgrade failed" followed by
   "Upgrade completed") and device reboots, log in to newly flashed
   system. Note you will now need to ssh as root rather than admin.

Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
[whitespace fixes, reordered partitions, removed rng node from 4.14,
fixed 901-arm-boot-add-dts-files.patch]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-21 00:57:54 +01:00
INAGAKI Hiroshi
5c11258297 ramips: add support for I-O DATA WN-AC733GR3
I-O DATA WN-AC733GR3 is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7620A.

Specification

- SoC		: MediaTek MT7620A
- RAM		: DDR2 64 MiB
- Flash		: SPI-NOR 8 MiB
- WLAN		: 2.4/5 GHz
  - 2.4 GHz : MT7620A (SoC), 2T2R
  - 5 GHz   : MT7610E, 1T1R
- Ethernet	: 10/100/1000 Mbps (RTL8367RB)
- LED/key	: 4x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J1: Vcc, RX, GND, TX from LED side
  - 57600n8

Flash instruction using factory image:

1. Boot WN-AC733GR3 normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-03-21 00:57:20 +01:00
Petr Štetiar
d2c3eb1e43 kernel: brcm47xx: Backport fixes for USB on WNDR3400v2 (fixes FS#2170)
Eric has reported on OpenWrt's bug tracking system[1], that he's not
able to use USB devices on his WNDR3400v2 device after the boot, until
he turns on GPIO #21 manually through sysfs.

1. https://bugs.openwrt.org/index.php?do=details&task_id=2170

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-20 23:18:46 +01:00
Petr Štetiar
846f98056a kernel: Backport ar933x_uart build fix (fixes FS#2152)
Andrey has reported on OpenWrt's bug tracking system[1], that he
currently can't use ar93xx_uart as pure serial UART without console
(CONFIG_SERIAL_8250_CONSOLE and CONFIG_SERIAL_AR933X_CONSOLE undefined),
because compilation ends with following error:

 ar933x_uart.c: In function 'ar933x_uart_console_write':
 ar933x_uart.c:550:14: error: 'struct uart_port' has no
                               member named 'sysrq'

1. https://bugs.openwrt.org/index.php?do=details&task_id=2152

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-20 23:07:03 +01:00
Evgeniy Didin
6c7b49c8b9 kernel: Update arc-add-OWRTDTB-section patch for 4.14
In 4.14.104 commit "e7264579eb80" (ARC: U-boot: check arguments paranoidly)
was introduced, which together with 332-arc-add-OWRTDTB-section.patch
caused build failure.

This commit updates 332-arc-add-OWRTDTB-section.patch.

Fixes:
http://phase1.builds.openwrt.org/builders/archs38%2Fgeneric/builds/1290
http://phase1.builds.openwrt.org/builders/archs38%2Fgeneric/builds/1269

Signed-off-by: Evgeniy Didin <evgeniy.didin@synopsys.com>
[Updated patch for kernel 4.19 in addition]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
2019-03-20 18:23:31 +01:00
Koen Vandeputte
e7a7749a3c kernel: fix compile issue for tda1997x media device
Building tda1997x fails now unless V4L2_FWNODE is selected:

drivers/media/i2c/tda1997x.o: in function `tda1997x_parse_dt'
undefined reference to `v4l2_fwnode_endpoint_parse'

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-19 09:19:41 +01:00
Wang Xin-yu (王昕宇)
57b1e951b5 ipq806x: Enlarge R7500v2 flash - use netgear partition
This patch increases available space from 20MB to 86MB.
Netgrear OEM firmware contains a 'netgear' partition followed 'ubi',
which can be used in openwrt for larger ubi space. (similar to
Netgear R7800).

original author (notmyrealhandle) tested this on R7500v2 and point that
OEM firmware can auto rebuild this partition (if used by openwrt).

Author: notmyrealhandle<22336358+notmyrealhandle@users.noreply.github.com>
Signed-off-by: Wang Xin-yu (王昕宇) <comicfans44@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [minor touch-ups]
2019-03-18 20:55:52 +01:00
Sven Roederer
f1396ac753 ath79: align naming of Ubiquiti Nanostation M
Support for the Nanostation M (XW) was added in 40530c8eb with board
name "nanostation-m-xw". The current image for the "Nanostation M"
uses "nano-m" as the board name.
This commit renames it to the full product name as it's used by all
other boards. The legacy boardname of the ar71xx target is added
via SUPPORTED_DEVICES to ease switching to ath79 target.

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[touch-ups on the commit message, removed subject remains]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-18 20:55:24 +01:00
Micke Prag
c3a17ee4b3 ramips: add #pwm-cells property to MT76x8 dts
To be able to configure pwms the pwm driver needs to know the number off
cells in the "pwms" property. For this platform this is 2.

Signed-off-by: Micke Prag <micke.prag@telldus.se>
2019-03-18 20:43:09 +01:00
Tomasz Maciej Nowak
b3a0c97b8c ath79: add support for jjPlus JA76PF2
jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board.

Specification
SoC:		Atheros AR7161
RAM:		64 MB DDR
Flash:		16 MB SPI NOR
Ethernet:	2x 10/100/1000 Mbps AR8316
		LAN (CN11), WAN/PoE (CN6 - close to power barrel
		connector, 48 V)
MiniPCI:	2x
LEDS:		4x, which 3 are GPIO controlled
Buttons:	2x GPIO controlled
		Reset (SW1, closer to ethernet ports), WPS (SW2)
Serial:		1x (only RX and TX are wired)
		baud: 115200, parity: none, flow control: none

Currently there is one caveat compared to ar71xx target images as the
MAC addresses are random on every reboot. To remedy this one needs to
store the WAN MAC address in RedBoot configuration. OpenWrt on first
boot, after flashing, will read out the address and assign proper ones
to both WAN and LAN ports. It is iportant to NOT keep the old
configuration when doing sysupgrade from ar71xx.

Upgrading from OpenWrt ar71xx image
1. Connect to serial port,
2. Download OpenWrt sysupgrade image to /tmp directory and flash it
   with:
    sysupgrade -n <openwrt_sysupgrade_image_name>
3. After writing new image OpenWrt will reboot, now interrupt boot
   process and enter RedBoot (bootloader) command line by pressing
   Ctrl+C,
4. Enter following commands (replace variable accordingly),
    set_mac (to view MAC addresses)
    alias ethaddr <wan_port_mac_adress>
    (confirm storing the value by inputting y and pressing Enter)
    reset
5. Now board should restart and boot OpenWrt with proper MAC addresses.

Installation
1. Prepare TFTP server with OpenWrt initramfs image,
2. Connect to WAN ethernet port,
3. Connect to serial port,
4. Power on the board and enter RedBoot (bootloader) command line by
   pressing Ctrl+C,
5. Enter following commands (replace variables accordingly):
    set_mac (to view MAC addresses)
    alias ethaddr <wan_port_mac_address>
    (confirm storing the value by inputting y and pressing Enter)
    ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress>
    load -r -b 0x80060000 <openwrt_initramfs_image_name>
    exec -c ""
6. Now board should boot OpenWrt initramfs image,
7. Download OpenWrt sysupgrade image to /tmp directory and flash it
   with:
    sysupgrade <openwrt_sysupgrade_image_name>
8. Wait few minutes, after the D2 LED will stop blinking, the board
   is ready for configuration.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-18 20:43:09 +01:00
Tomasz Maciej Nowak
8f6f260302 ath79: routerstation: prepare to use sysupgrade-tar format image
In PR [1] introducing initial support for Ubiquiti RouterStation boards,
Mathias Kresin suggested to replace the combined sysupgrade image with
tarball generated by sysupgrade-tar.sh. This would simplify deployment
of sysupgrade as the kernel size (needed to update FIS partition) could
be simply calculated on the fly instead of reading value from combined
image header. Unfortunately this would break sysupgrade compatibility
between ar71xx image and ath79 image. Therefore this commit creates
migration path to use new sysuprade image, it adds code to accept both
of them at this moment. The plan is to keep it until new stable version
is released. Then the image recipe should be changed to new format and
compatibility code for old image removed.

1. https://github.com/openwrt/openwrt/pull/1237

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-18 20:43:09 +01:00
Martin Schiller
f3da2ebf90 lantiq: kernel 4.14: fix usb_phy1 reset status bit in vr9.dts
The status of USB PHY 1 Reset Domain is also in bit 5 of RST_STAT2.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-03-18 20:42:30 +01:00
Tomasz Maciej Nowak
9fd2a3faa5 ath79: qca955x: add wmac migration hotplug event
When upgrading from ar71xx target images to ath79 based ones, the
integrated wireless interface changes its sysfs path. Therefore the
previous enabled wireless interface will be disabled, which can cause
false complains about it not working. This commit adds hotplug event
which migrates to new path and will keep the wrireless interface
enabled after upgrade.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-18 20:42:29 +01:00
Tomasz Maciej Nowak
50674ccade ath79: fix leds description for EnGenius EPG5000
Align the LEDs deffinition with MACH file present in ar71xx target which
has the correct LED functions and colors adescription.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-18 20:42:29 +01:00
Koen Vandeputte
a8cfef6c45 kernel: bump 4.14 to 4.14.106
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-18 10:02:51 +01:00
Koen Vandeputte
79fc997e48 kernel: bump 4.9 to 4.9.163
Refreshed all patches.

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-18 10:02:51 +01:00
Felix Fietkau
1f68aac9d7 kernel: backport flow dissector batman-adv support
Improves performance on multicore systems handling batman-adv traffic

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-03-16 19:59:02 +01:00
Rosen Penev
96e0fa94c7 ath79: ag71xx: Remove ndo_poll_controller
It is unused by default and upstream is trying to remove it as it has
negative effects when the driver is under load. Upstream explanation:

netpoll: avoid capture effects for NAPI drivers
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC).

This capture, showing one ksoftirqd eating all cycles
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.

It seems that all networking drivers that do use NAPI
for their TX completions, should not provide a ndo_poll_controller() :

Most NAPI drivers have netpoll support already handled
in core networking stack, since netpoll_poll_dev(
 uses poll_napi(dev) to iterate through registered
NAPI contexts for a device.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2019-03-13 16:35:45 +01:00
Adrian Schmutzler
26f7cf8ac3 ar71xx: Speed up mtd extraction in ar71xx.sh
Although the amount of data read here is smaller than for the
caldata, there still might be some speed gain compared to reading
bytewise. And there is no harm ...

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-03-13 16:27:41 +01:00
Adrian Schmutzler
51fb186cb3 ar71xx: Speed up caldata/eeprom handling
Reading and writing to and from flash storage is slowed down
enormously by some functions which use a block size of 1.

This patch reworks the extraction scripts to be much faster and
efficient by reading and writing in possibly one big block.

This is based on the initial commit a69e101 for ipq40xx by
Christian Lamparter <chunkeey@gmail.com>.

Speed comparison @ TP-Link TL-WDR4300 (just manually) results
in a time reduction by three orders of magnitude (99.9 %).

> time dd if=/dev/mtd3 of=/lib/firmware/test-slow bs=1 count=4096 skip=4096
4096+0 records in
4096+0 records out
real    0m 15.85s
user    0m 0.06s
sys     0m 13.28s

> time dd if=/dev/mtd3 of=/lib/firmware/test-fast bs=4096 count=1 skip=4096 iflag=skip_bytes
1+0 records in
1+0 records out
real    0m 0.02s
user    0m 0.00s
sys     0m 0.02s

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-03-13 16:27:41 +01:00
Adrian Schmutzler
e1ba59ea5c ath79: Speed up caldata/eeprom handling
Reading and writing to and from flash storage is slowed down
enormously by some functions which use a block size of 1.

This patch reworks the extraction scripts to be much faster and
efficient by reading and writing in possibly one big block.

This is based on the initial commit a69e101 for ipq40xx by
Christian Lamparter <chunkeey@gmail.com>.

Speed comparison @ UBNT AC-Mesh (just manually) results
in a time reduction by three orders of magnitude (99.9 %).

> time dd if=/dev/mtd6 of=/lib/firmware/test-slow bs=1 count=4096 skip=4096
4096+0 records in
4096+0 records out
real    0m 16.84s
user    0m 0.07s
sys     0m 13.54s

> time dd if=/dev/mtd6 of=/lib/firmware/test-fast bs=4096 count=1 skip=4096 iflag=skip_bytes
1+0 records in
1+0 records out
real    0m 0.02s
user    0m 0.00s
sys     0m 0.02s

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Rosen Penev <rosenp@gmail.com>
2019-03-13 16:27:41 +01:00
kbuild test robot
91a7791115 apm821xx: usb: xhci: fix semicolon.cocci warnings
drivers/usb/host/xhci-pci.c:788:2-3: Unneeded semicolon

 Remove unneeded semicolon.

Generated by: scripts/coccinelle/misc/semicolon.cocci

Fixes: 9e0fd1b52a ("apm821xx: add support for the Netgear Centria N900 WNDR4700/WNDR4720")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [changed subject]
2019-03-13 16:25:37 +01:00
Linus Walleij
ac5f431ad1 gemini: Generate padded kernel+rootfs images for DIR-685
We currently generate a kernel that boots from the harddrive
in the DIR-685. That's not how we usually do things, so
let's augment it to boot from flash and mount the rootfs
using squashfs and JFFS2 like everyone else.

Partition splitting only work when the partitions are
inside of a "partitions" node which is why we have a patch
like this (submitted upstream).

Another patch drops the rootfs arguments and renames the
firmware partition while adding the compatible "wrg"
to it so the WRGG parser will kick in.

Factory image was tested by bravely reflashing the DIR-685
from stock firmware using the web UI and the serial console
boot loader.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-03-13 16:25:36 +01:00
Linus Walleij
b907097291 kernel: mtdsplit: wrgg: Support big and little endian
The WRGG images exist in both big and little endian variants,
as can be seen from the image generator in
tools/firmware-utils/src/mkwrggimg.c, you either pass
the "-b" flag or not. The D-Link DIR-685 is using little
endian images so we need to support splitting these.

Detect endianness like this: if the kernel entity size
gets silly big (bigger than the flash memory) we are
probably using the wrong endianness.

Example: my kernel of 0x0067ff64 was switched around by
wrong endianness and detected as 0x64ff67a0 (the actual
size in swapped endianness + header 0xa0).

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-13 16:25:36 +01:00
Tomasz Maciej Nowak
ee34740ca3 ath79: add suport for EnGenius EPG5000
EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band
wireless router.

Specification
SoC:		Qualcomm Atheros QCA9558
RAM:		256 MB DDR2
Flash:		16 MB SPI NOR
WIFI:		2.4 GHz 3T3R integrated
		5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet:	5x 10/100/1000 Mbps QCA8337N
USB:		1x 2.0
LEDS:		4x GPIO controlled
Buttons:	2x GPIO controlled
UART:		4 pin header, starting count from white triangle on PCB
		1. VCC 3.3V, 2. GND, 3. TX, 4. RX
		baud: 115200, parity: none, flow control: none

Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Tools > Firmware,
4. Select OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
   is ready for configuration.

Alternative installation
1. Prepare TFTP server with OpenWrt sysupgrade image,
2. Connect to one of LAN (yellow) ethernet ports,
3. Connect to UART port (leaving out VCC pin!),
4. Power on router,
5. When asked to enter a number 1 or 3 hit 2, this will select flashing
   image from TFTP server option,
6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8),
   then router ip (default is 192.168.99.9) and for last, image name
   downloaded from TFTP server (default is uImageESR1200_1750),
7. After providing all information U-Boot will start flashing the image,
   You can observe progress on console, it'll take few minutes and when
   the Power LED will stop blinking, router is ready for configuration.

Additional information
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: aigo3d0a0tdagr
useful for creating backup of original firmware.
When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep
the old configuration.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-13 16:25:35 +01:00
Marius Genheimer
41a86debe3 ipq40xx: limit frequencies for Asus Lyra
The Asus Lyra has filters in the antenna paths which limits
the usable frequencies on both 5GHz radios.

Signed-off-by: Marius Genheimer <mail@f0wl.cc>
2019-03-13 16:25:35 +01:00
David Bauer
148d29d47b ipq40xx: add support for AVM FRITZ!Repeater 3000
Hardware
--------
CPU:   Qualcomm IPQ4019
RAM:   256M (NANYA NT5CC128M16JR-EK)
FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI)
ETH:   Qualcomm QCA8072
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
WiFi5: QCA9984 4T4R 4SS n/ac
LED:    - Connect green/blue/red
        - Power green
BTN:   WPS/Connect
UART:  115200n8 3.3V
       VCC - RX - TX - GND (Square is VCC)

Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz3000'
   subdirectory. Place it in the same directory as the 'eva_ramboot.py'
   script. It is located in the 'scripts/flashing' subdirectory of the
   OpenWRT tree.

2. Assign yourself the IP address 192.168.178.10/24. Connect your
   Computer to one of the boxes LAN ports.

3. Connect Power to the Box. As soon as the LAN port of your computer
   shows link, load the U-Boot to the box using following command.

   > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin

4. The U-Boot will now start. Now assign yourself the IP address
   192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
   server root directory and rename it to 'FRITZ3000.bin'.

5. The Box will now boot OpenWRT from RAM. This can take up to two
   minutes.

6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
   scp. SSH into the Box and first write the Bootloader to both previous
   kernel partitions.

   > mtd write /path/to/uboot-fritz3000.bin uboot0
   > mtd write /path/to/uboot-fritz3000.bin uboot1

7. Remove the AVM filesystem partitions to make room for our kernel +
   rootfs + overlayfs.

   > ubirmvol /dev/ubi0 --name=avm_filesys_0
   > ubirmvol /dev/ubi0 --name=avm_filesys_1

8. Flash OpenWRT peristently using sysupgrade.

   > sysupgrade -n /path/to/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-13 16:25:35 +01:00
David Bauer
5389db72e3 fritz-tools: add support for IPQ40xx platform
AVM devices based on Qualcomm IPQ40xx do not store sector health
information in the OOB area. Make this check optional to support this
platform.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-13 16:25:34 +01:00
Jeff Kletsky
fefa34def8 ath79: Add GL.iNet AR-300M-Lite
AR300M-Lite is single-Ethernet variant of the AR300M series
Its eth0 would otherwise be assigned to the WAN interface
making it unreachable firstboot or failsafe.

Installation instructions from OEM (OpenWrt variant):
* Install sysupgrade.bin using OEM's "Advanced" GUI (LuCI),
   * Do not preserve settings
   * Access rebooted device via Ethernet at OpenWrt default address

Add previously missing LED defaults for all three variants;
-nand, -nor, -lite to the definitions in 01_leds

Non-lite variants thanks to Andreas Ziegler
https://patchwork.ozlabs.org/patch/1049396/

Runtime-tested:  GL.iNet AR300M-Lite

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-03-13 16:25:34 +01:00
Chen Minqiang
7dfe357a3d ramips: HC5861 drop unused gpio group define in dts
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2019-03-13 16:25:34 +01:00
Ozgur Can Leonard
d009033911 ramips: add support for Xiaomi Mi Router 3 Pro
Hardware:

CPU:   MediaTek MT7621AT (2x880MHz)
RAM:   512MB DDR3
FLASH: 256MB NAND
WiFi:  2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!)
WiFI:  5GHz 4x4 MT7615 a/n/ac  (Needs driver, See Issues!)
USB:   1x 3.0
ETH:   1x WAN 10/100/1000 3x LAN 10/100/1000
LED:   Power/Status
BTN:   RESET
UART:  115200 8n1

Partition layout and boot:

Stock Xiaomi firmware has the MTD split into (among others)

- kernel0 (@0x200000)
- kernel1 (@0x600000)
- rootfs0
- rootfs1
- overlay (ubi)

Xiaomi uboot expects to find kernels at 0x200000 & 0x600000
referred to as system 1 & system 2 respectively.
a kernel is considered suitable for handing control over
if its linux magic number exists & uImage CRC are correct.
If either of those conditions fail, a matching sys'n'_fail flag
is set in uboot env & a restart performed in the hope that the
alternate kernel is okay.
If neither kernel checksums ok and both are marked failed, system 2
is booted anyway.

Note uboot's tftp flash install writes the transferred
image to both kernel partitions.

Installation:

Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in
kernel0 for ease of recovery, and install OpenWRT into kernel1 and
after.

The installation file for OpenWRT is a *squashfs-factory.bin file that
contains the kernel and a ubi partition. This is flashed as follows:

nvram set flag_try_sys1_failed=1
nvram set flag_try_sys2_failed=0
nvram commit
dd if=factory.bin bs=1M count=4 | mtd write - kernel1
dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0
reboot

Reverting to stock:

The part of stock firmware we've kept in kernel0 allows us to run stock
recovery, which will re-flash stock firmware from a *.bin file on a USB.

For this we do the following:

fw_setenv flag_try_sys1_failed 0
fw_setenv flag_try_sys2_failed 1
reboot

After reboot the LED status light will blink red, at which point pressing
the 'reset' button will cause stock firmware to be installed from USB.

Issues:

OpenWRT currently does not have support for the MT7615 wifi chips. There is
ongoing work to add mt7615 support to the open source mt76 driver. Until that
support is in place, there are closed-source kernel modules that can be used.

See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[02_network remaps, Added link to notes]
2019-03-13 16:25:34 +01:00
Santiago Piccinini
24463d0d94 ath79: add support for LibreRouter v1
Hardware
--------
SOC:   QCA9558
RAM:   128M DDR2
Flash: 16MiB SPI-NOR
ETH:   QCA8337N: 2x 10/100/1000 PoE and PoE pass-through
WiFi2: QCA9558 (bgn) 2T2R
WiFi5: 2x mPCIE with AR9582 (an) 2T2R
BTN:   1x Reset
GPIO:  multiple GPIO on header, PoE passthrough enable
UART:  3.3V 115200 8N1 header on the board
WDG:   ATTiny13 watchdog
JTAG:  header on the board
USB:   1x connector and 1x header on the board
PoE:   10-32V input in ETH port 1, passthrough in port 2
mPCIE: 2x populated with radios (but replaceable)

OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin
using the web interface or with sysupgrade -n.

Flash from bootloader (in case failsafe does not work)
1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART
   header in the board.
2. Connect an ETH cable and configure static ip addres 192.168.1.10/24
3. Turn on the device and stop the bootloader sending any key through the serial
   interface.
4. Use a TFTP server to serve <your image>-sysupgrade.bin file.
5. Execute the following commands at the bootloader prompt:
    ath> tftp 82000000 <your image>-sysupgrade.bin
    ath> erase 0x9f050000 +$filesize
    ath> cp.b 0x82000000 0x9f050000 $filesize
    ath> bootm 0x9f050000

More docs
* Bootloader https://github.com/librerouterorg/u-boot
* Board details (schematics, gerbers): https://github.com/librerouterorg/board

Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
2019-03-13 16:25:34 +01:00
David Bauer
93601d647f ipq40xx: fix FRITZBox 7530 NAND controller node
This removes the 'cs-gpios' property from the AVM FRITZ!Box 7530 NAND
controller node. As pointed out by Christian Lamparter, the property is
not needed by the Qualcomm NAND controller driver.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-13 16:25:34 +01:00
Christian Lamparter
784f2e73df ipq40xx: fix phy interrupt setting
This patch fixes a problem that was discovered during DSA
development. On the MR33, the link change events from the
external AR8035-PHY would never make it to the qca8k driver.

The issue turned out to be a misplaced memcpy that was copying
over the zero-initialized irq table, when it should have been
set to PHY_POLL. Hence this patch moves the memcpy after the
array has been initialized.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-13 16:25:34 +01:00
Christian Lamparter
39092ad9e9 ipq40xx: tidy up 02_networks
- fix linksys' EA6350v3 order

 - remove whitespace that should have been tabs

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-13 16:25:34 +01:00
Daniel Golle
8c593804d0 oxnas: install wireless driver on pogoplugpro
PogoPlug Pro comes with AzureWave AW-NE762H PCIe module containing
Ralink's Rt3090 chip supported by the rt2x00 driver.
Install the driver as well as wpad-basic.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-12 14:18:42 +01:00
Daniel Golle
74ef848b96 oxnas: also akitio,mycloud uses PCIe apparently
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-12 01:06:33 +01:00
Daniel Golle
0e9b11213e oxnas: enable pcie_phy on boards utilizing PCIe
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-12 00:35:16 +01:00
Piotr Dymacz
db91418766 ath79: add support for TP-Link RE350K v1
TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range
extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros
QCA9558 + QCA9882 + AR8035 platform and is available only on US market.

Specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 1x 1 Gbps Ethernet (AR8035)
- 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11)
- 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11)
- 2x U.FL connector on PCB
- 2x dual-band PCB antennas
- 1x LED, 2x dual-color LED (all driven by GPIO)
- 3x button (app config, led, reset)
- 1x mechanical on/off slide switch
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x JTAG (8-pin, 1.27 mm pitch) header on PCB

Flash instruction:
Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254,
default credentials: admin/admin).

Warning:
This device does not include any kind of recovery mechanism in U-Boot.

Vendor firmware access:
You can access vendor firmware over serial (RX line requires jumper
resistor in R306 place, near XTAL) with: root/sohoadmin credentials.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-11 22:00:26 +01:00
Piotr Dymacz
9b6413982c ramips: add support for ALFA Network Tube-E4G
ALFA Network Tube-E4G is an outdoor, dual-SIM LTE Cat. 4 CPE, based on
MediaTek MT7620A, equipped with Quectel EC25 miniPCIe modem.

Specification:

- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 1x detachable antenna (modem main)
- 1x internal antenna (modem div)
- 1x GPS passive antenna (optional)
- 5x LED (all driven by GPIO)
- 1x button (reset)
- UART (4-pin, 2.54 mm pitch) header on PCB

Other:

Default SIM slot is selected at an early stage by U-Boot, based on
'default_sim' environment value: 1 or unset = SIM1 (mini), 2 = SIM2
(micro). U-Boot also resets the modem, using #PERST signal, before
starting kernel.

Flash instruction:

You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:

1. Power the device with reset button pressed, the LAN LED will start
   blinking slowly and after ~3 seconds, when it starts blinking faster,
   you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-11 22:00:26 +01:00
Michael Heimpold
6ac5144b13 mxs: disable unused serial drivers
This disables PL010 and 8250 serial support for this platform
as both drivers are not used: the debug UART is PL011 and the
application UARTs use a dedicated MXS specific driver.

The kernel size reduction is neglectable, but it also removes
the non-working (confusing) /dev/ttyS0 and /dev/ttyS1 devices
in a running system (which generate errors when trying to use):

  root@OpenWrt:~# echo "hello world" > /dev/ttyS0
  ash: write error: I/O error
  root@OpenWrt:~#

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2019-03-11 19:35:43 +01:00
Daniel Golle
b4917fa907 oxnas: fix oxnas-rps-timer dt-match
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-11 15:01:37 +01:00
Daniel Golle
87a81455a1 oxnas: replace oxnas-restart with version to be submitted to upstream
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-11 13:39:33 +01:00
Daniel Golle
d6fa04a437 IB: include SUPPORTED_DEVICES in 'make info' output
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-11 05:32:29 +01:00
Daniel Golle
35a7f79096 oxnas: use generic filenames for image and DTS
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-11 03:43:30 +01:00
Daniel Golle
8ad0ba3a07 oxnas: move PCIe controller outside of simple-bus
Move PCIe controller outside down to SoC level to avoid resource
mapping problems.
Also add more detailed error handling when mapping registers.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-10 23:04:28 +01:00
Hauke Mehrtens
a18e2994df lantiq: Refresh kernel 4.14 configuration
This adds two configuration options which are getting automatically
added.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-03-10 19:05:49 +01:00
Daniel Golle
8f9155fe7a oxnas: fix PCIe register ranges in device-tree
They should be relative to apb-bridge@47000000 rather than to the
pcie-controller@c00000 inside it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-10 17:57:50 +01:00
Mathew McBride
6a2705a52f layerscape: use wrapped nand_do_upgrade for traverse-ls1043 boards
Traverse LS1043 boards are set up with a dual-system layout, rootfs{1,2} and kernel{1,2}.
nand_do_upgrade can do the image replacement work we were doing before as long as we give it the partition names.
This greatly simplifies the /lib/upgrade/platform.sh.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2019-03-10 17:48:23 +01:00
Mathew McBride
17468cc090 layerscape: rename Traverse boards along SoC lines
Upcoming product specification and branding changes mean that the names in tree do not accurately reflect released products.
To reduce any confusion, sort our boards by SoC family, e.g traverse-ls1043. Any future boards using Layerscape family SoC's
will be treated the same way, e.g Device/traverse-ls/lx/laXXXX.
The affected boards so far have only been available through OEM channels and those aren't using the provided sysupgrade.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2019-03-10 17:48:23 +01:00
Martin Schiller
ff3cfe0848 ltq-atm/ltq-ptm: re-enable/fix reset_ppe() functionality for VR9
This patch re-enables the reset_ppe() functionality for VR9 targets by using
the new lantiq rcu subsystem. The reset sequence in the reset_ppe() function
was taken from the ppa datapath driver of lantiq UGW 7.4.1.

Additionally it adds the required reset definitions to the vr9 dtsi file.

It also prepares the reset_ppe() function calls for the other lantiq targets.

This feature is needed to be able to switch between ltq-atm/ltq-ptm driver
in ATM/PTM Auto-Mode at runtime.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-03-10 16:49:31 +01:00
Danijel Tudek
eae6cac6a3 lantiq: add support for AVM FRITZ!Box 7362 SL
Hardware:
- SoC: Lantiq VRX288
- RAM: Winbond W971GG6JB 1 Gb (128 MiB)
- Flash:
  - SPI: 8 Mb (1 MiB) for bootloader and tffs
  - NAND: 1 Gb (128 MiB) for OS
- xDSL: Lantiq VRX208
- WLAN: Atheros AR9381
- DECT: Dialog Semiconductors SC14441

Everything except FXS/DECT works
(no drivers for AVM's FXS implementation with SC14441).

Installation via FTP:
1. Use scripts/flashing/eva_ramboot.py to send initramfs-kernel.bin
to the device when powering on.
Standard AVM procedures with finding the correct IP address and
the right moment to open FTP apply here (approx. 4 seconds on 7362SL).
IMPORTANT: set lzma compression in ramdisk options, bootloader stalls
when receiving uncompressed images.

2. Transfer sysupgrade.bin image with scp to /tmp directory
and run sysupgrade

3. First boot might take a bit longer if linux_fs_start was set to 1,
in that case the device will reboot twice, first time it will fail to load
second kernel (overwritten by ubifs), set linux_fs_start to 0 and reboot.

OpenWrt uses the entire NAND flash. Kernel uses 4 MiB and rootfs uses
the rest of 124 MiB, overwriting everything related to FRITZ!OS - both
OS images, config and answering machine/media server data.
To return to FRITZ!OS, use AVM's recovery image.

Signed-off-by: Danijel Tudek <danijel.tudek@gmail.com>
2019-03-10 16:49:31 +01:00
Danijel Tudek
5026f43559 lantiq: move common FRITZ736X bits into dtsi
Move common FRITZ736X bits into dtsi file
as a preparation for FRITZ7362SL support.

Signed-off-by: Danijel Tudek <danijel.tudek@gmail.com>
2019-03-10 16:49:31 +01:00
Andy Binder
20f48c8ae3 lantiq: add support for AVM FRITZ!Box 7412
Hardware:

SoC: Lantiq VRX 220
CPU Cores: 2x MIPS 34Kc at 500 MHz
RAM: 128 MiB 250 MHz
Storage: 128 MiB NAND flash
Ethernet: built-in Fast Ethernet switch, only port 2 is used
Wireless: Atheros AR9287-BL1A b/g/n with 2 pcb antennas
Modem: built-in A/VDSL2 modem
DECT: Dialog SC14441
LEDs: 1 two-color, 4 one-color
Buttons: 2
FXS: 1 port via TAE or RJ12 connector
Everything except FXS/DECT works
(no drivers for AVM's FXS implementation with SC14441).

Installation:

Use the eva_ramboot.py script to load an initramfs image on the
device. Run it a few seconds after turning the device on.
$ scripts/flashing eva_ramboot 192.168.178.1 bin/targets/lantiq/xrx200/openwrt-lantiq-xrx200-avm_fritz7412-initramfs-kernel.bin
If it fails to find the device try the ip address 169.254.120.1.
(Firmware updates or the recovery tool apparently change it.)

IMPORTANT: set lzma compression in ramdisk options, bootloader stalls
when receiving uncompressed images.

The device will load it in ram and boot it. You can reach it under
the openwrt default ip address 192.168.1.1.

Check if the key linux_fs_start is not set to 1 in tffs:
$ fritz_tffs_nand -d /dev/mtd1 -n linux_fs_start
If it is set to 1, the bootloader will select the wrong set of
partitions. Restart the box and install an FritzOS upgrade or do a
recovery. Afterwards start again at step 1.

Run sysupgrade to persistently install OpenWRT.

Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.de>
Signed-off-by: Andy Binder <AndyBinder@gmx.de>
2019-03-10 16:49:31 +01:00
Aleksander Jan Bajkowski
445ca981d1 sunxi: add support for Orange Pi PC Plus
CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz
GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0)
Memory: 1GB DDR3 (shared with GPU)
Onboard: Storage TF card (Max. 64GB) / MMC card slot
Onboard: Storage 8 GB eMMC
Onboard: Network 10/100M Ethernet RJ45
Onboard: Network WiFi 802.11 b/g/n (Realtek RTL8189FTV)
Onboard header: SPI, I2C, GPIO, UART
USB 2.0: Three USB 2.0 HOST, One USB 2.0 OTG

Known issues:
-Wifi diesn't work

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2019-03-09 18:55:15 +01:00
Piotr Dymacz
6fa94d5e8f ath79: add support for YunCore A770
YunCore A770 is a ceiling AC750 AP with 2 Fast Ethernet ports, PoE
(802.3at) support, based on QCA9531 + QCA9887.

Specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet (PoE 802.3at support in WAN port)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887), with ext. FEM (SKY85728-11)
- 2x regular LED, 1x RGB LED (all driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART header on PCB

Flash instruction:

1. First, gain root access to the device, following below steps:

- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to 'Advanced' -> 'Management' -> 'System' and download backup of
  configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update 'shadow' file and change
  hash of root password to something known.
- Repack the archive, rename it back to 'bakfile.bin' and use to
  restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.

2. Then, install OpenWrt:

- Login over SSH and issue command:
  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload 'sysupgrade' image and install it (only if previous command
  succeeded) with command: 'sysupgrade -n -F openwrt-...'.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-09 16:31:17 +01:00
Piotr Dymacz
24de7c29e5 ipq40xx: backport I2C QUP driver changes from 4.17
Backport below changes for I2C QUP driver from v4.17:

  0668bc44a426 i2c: qup: fix copyrights and update to SPDX identifier
  7239872fb340 i2c: qup: fixed releasing dma without flush operation completion
  eb422b539c1f i2c: qup: minor code reorganization for use_dma
  6d5f37f166bb i2c: qup: remove redundant variables for BAM SG count
  c5adc0fa63a9 i2c: qup: schedule EOT and FLUSH tags at the end of transfer
  7e6c35fe602d i2c: qup: fix the transfer length for BAM RX EOT FLUSH tags
  3f450d3eea14 i2c: qup: proper error handling for i2c error in BAM mode
  08f15963bc75 i2c: qup: use the complete transfer length to choose DMA mode
  ecb6e1e5f435 i2c: qup: change completion timeout according to transfer length
  6f2f0f6465ac i2c: qup: fix buffer overflow for multiple msg of maximum xfer len
  f7714b4e451b i2c: qup: send NACK for last read sub transfers
  fbfab1ab0658 i2c: qup: reorganization of driver code to remove polling for qup v1
  7545c7dba169 i2c: qup: reorganization of driver code to remove polling for qup v2

This fixes various I2C issues observed on AP120C-AC board equipped with
Atmel/Microchip AT97SC3205T TPM module.

Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-08 19:28:31 +01:00
Piotr Dymacz
ff8a8074b2 ipq40xx: add ath10k-calibration-variant in AP120C-AC DTS
Use 'ath10k-calibration-variant' (with the value sent upstream) for the
second (5 GHz) radio in AP120C-AC board DTS. First radio uses the same
BDF as in one of Qualcomm reference designs.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-08 19:28:31 +01:00
Paul Spooren
483498808e ib: show current revision based on $(REVISION)
This is useful in for the attendedsyupsgrade server (asu) to
distinguish between snapshot version. Currently asu can't tell devices
requesting a snapshot build if the same build is already installed.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-03-08 01:18:12 +01:00
Paul Spooren
f37afec866 ib: show unified target based on $(TARGETID)
Instead of showing a slightly more readable target like
"ar71xx (Generic)" print the more generic format "ar71xx/genric"

Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-03-08 01:18:12 +01:00
Koen Vandeputte
364ab348dc kernel: bump 4.14 to 4.14.105
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-07 16:32:23 +01:00
Koen Vandeputte
3ca38dcfa2 kernel: bump 4.9 to 4.9.162
Refreshed all patches.

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-07 16:32:23 +01:00
Christian Lamparter
457de5a154 owl-loader: fix crash caused by endian patch
This patch fixes a crash that occured on the
BT Home Hub v5a (lantiq/xrx200) which resulted
in the device bootlooping.

Reported-by: Ryan Mounce <ryan@mounce.com.au>
Tested-by: Vitalij Alshevsky <v_alshevsky@tut.by>
Fixes: ddece08bf4 ("kernel: owl-loader: fix sparse endian warnings")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-06 22:02:56 +01:00
Mantas Pucka
a4ba41863b mips: fix dynamic ftrace
This was fixed for v4.9 in 076d2ea68, now port to all kernels

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2019-03-06 22:02:56 +01:00
Chen Minqiang
e15bda603a ramips: rework network settings for HC5861
dts: disable port4 and leave it ephy mode because it connect to nothing
switch port5 connected to GE port we use it as wan port

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2019-03-06 22:02:56 +01:00
Mantas Pucka
fe591f2fe2 ar71xx: enable QCA955x SGMII fixup on Rambutan
fixes intermittent loss of connectivity on 1Gbit port, with
log message:

  803x_aneg_done: SGMII link is not ok

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2019-03-06 22:02:56 +01:00
Christian Lamparter
33727ecea5 lantiq: enlarge ZyXEL P-2812HNU-F1 kernel partition (FS#2124)
The current snapshot release kernel with it's 2119245 Byte
size is too big to fit into the 2097152 (2MiB) area that
was set aside for the kernel. Which causes the device to
fail to boot (after an update or even during a fresh install)

 NAND read: device 0 offset 0x60000, size 0x200000
  2097152 bytes read: OK
 ## Booting kernel from Legacy Image at 80800000 ...
    Image Name:   MIPS OpenWrt Linux-4.14.98
    Created:      2019-02-13   9:37:36 UTC
    Image Type:   MIPS Linux Kernel Image (lzma compressed)
    Data Size:    2119245 Bytes = 2 MiB
    Load Address: 80002000
    Entry Point:  80002000
    Verifying Checksum ... Bad Data CRC
 ERROR: can't get kernel image!

This patch fixes the problem by enlarging the kernel partition
at the cost of the ubi/data partition behind it. The patch
also adds a KERNEL_SIZE variable to the image Makefile to
prevent silent corruptions from happening in the future.

Please note: The u-boot environment for the router also
needs to be updated. So please attach an appropriate
serial converter cable and enter the following commands
into the u-boot prompt:

 setenv nboot 'nand read 0x80800000 0x60000 0x300000; bootm 0x80800000'
 saveenv

The wiki has been updated accordingly:
<https://openwrt.org/toh/zyxel/p2812hnu-f1>

Fixes: FS#2124
Suggested-by: Mafketel (User on bugs.openwrt.org)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-06 21:58:59 +01:00
Daniel Golle
13c379e5c6 ib: display whether profile comes with image metadata
Having image metadata (and signature) appended is a condition for
semi-automated sysupgrade, hence IB needs to be able to tell which
images will end up with metadata.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-06 14:50:42 +01:00
Daniel Golle
c8778250a9 ramips: mt7620: export chip version and pkg
Similar to the (currently unused) mt7620_get_eco() function, introduce
mt7620_get_chipver() and mt7620_get_pkg() functions to allow rt2x00 to
probe for the type of WiSoC. This is ugly and probably unacceptable
for upstream, however, it should help to evaluate which of those hacks
are actually really needed, enumerate the possible values and label
them in a more meaningful way than currently done in the vendor driver.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-06 01:11:54 +01:00
Rafał Miłecki
9e32e288f0 kernel: fix refcnt leak in LED netdev trigger on interface rename
This fixes a possible unbalanced dev_hold():
> iw dev bar del
[  237.355366] unregister_netdevice: waiting for bar to become free. Usage count = 1
[  247.435362] unregister_netdevice: waiting for bar to become free. Usage count = 1
[  257.545366] unregister_netdevice: waiting for bar to become free. Usage count = 1

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-03-05 23:10:09 +01:00
Koen Vandeputte
d3506d1bc1 ar71xx: ag71xx: fix compile error when enabling debug
Starting from kernel 4.5, phy_id needs to be fetched from a different location.

not doing so results in this compile error:

drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.c: In function 'ag71xx_phy_connect_multi':
drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.c:133:35: error: 'struct mdio_device' has no member named 'phy_id'
    ag->mii_bus->mdio_map[phy_addr]->phy_id);
                                   ^
./include/linux/printk.h:137:18: note: in definition of macro 'no_printk'
    printk(fmt, ##__VA_ARGS__); \
                  ^~~~~~~~~~~
drivers/net/ethernet/atheros/ag71xx/ag71xx.h:72:27: note: in expansion of macro 'pr_debug'
 #define DBG(fmt, args...) pr_debug(fmt, ## args)
                           ^~~~~~~~
drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.c:130:3: note: in expansion of macro 'DBG'
   DBG("%s: PHY found at %s, uid=%08x\n",
   ^~~
scripts/Makefile.build:326: recipe for target 'drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.o' failed

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-05 13:19:43 +01:00
Koen Vandeputte
1cfbf95393 kernel: bump 4.14 to 4.14.104
Refreshed all patches.

Altered patches:
- 332-arc-add-OWRTDTB-section.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-05 13:19:43 +01:00
Koen Vandeputte
fc45ae4461 kernel: bump 4.9 to 4.9.161
Refreshed all patches.

Altered patches:
- 332-arc-add-OWRTDTB-section.patch

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-05 13:19:43 +01:00
Petr Štetiar
40530c8eb4 ath79: Add support for Ubiquiti Nanostation M (XW)
CPU:  AR9342 SoC
RAM:      64 MB DDR2
Flash:     8 MB NOR SPI
Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch
WLAN:  2.4/5 GHz
UART:      1 UART
LEDs:        Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:     Reset

Flashing instructions using recovery method over TFTP

 1. Unplug the ethernet cable from the router.
 2. Using paper clip press and hold the router's reset button. Make sure
    you can feel it depressed by the paper clip. Do not release the button
    until step 4.
 3. While keeping the reset button pressed in, plug the ethernet cable
    back into the AP. Keep the reset button depressed until you see the
    device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
    LED2/LED4), this may take up to 25 seconds.
 4. You may release the reset button, now the device should be in TFTP
    transfer mode.
 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
    should work.
 6. Plug the PoE injector's LAN cable directly to your computer.
 7. Start tftp client and issue following commands:
     tftp> binary
     tftp> connect 192.168.1.20
     tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin

Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-05 03:15:52 +01:00
Petr Štetiar
368b6d1a52 ath79: gmac: ar934x: Add parser for mii-gmac0-slave
While converting Nanostation M XW from current ar71xx code to ath79 I've
hit one issue, where the ethernet networking wasn't working, so I was
checking every bit in the networking setup path between ar71xx and
ath79.

I've came to the following code in ar71xx/mach-ubnt-xm.c:

 static void __init ubnt_xw_init(void) {
 	...
 	ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_MII_GMAC0 |
                                   AR934X_ETH_CFG_MII_GMAC0_SLAVE);
 	...
 }

Where this code is setting AR934X_ETH_CFG_MII_GMAC0_SLAVE bit in
AR934X_GMAC_REG_ETH_CFG register, but I couldn't find a way of setting
this bit from DTS, so this patch adds `mii-gmac0-slave` DTS property
which allows setting of this bit in `gmac-config`, which is then used in
Nanostation M XW DTS.

Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-05 03:15:52 +01:00
Chuanhong Guo
47f0be676f ath79: qca955x: assert mdio/gmac reset together
This allows resetting gmac registers during initialization.
Also add compatible string for qca955x mdio to enable more mdio
clock dividers.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-05 03:02:34 +01:00
Chuanhong Guo
51cdf0e9eb ath79: ar934x: assert mac/mdio reset together for gmac0
This allows resetting gmac registers during initialization.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-05 03:02:34 +01:00
Chuanhong Guo
cea3e9e438 ath79: ag71xx: add support for optional mdio reset
On ar933x and later chips, there are separated mac/mdio resets, but
resetting the entire gmac block with register values requires both
mac_reset and mdio_reset to be asserted together.

Add support for optional mdio reset so that we can do a full reset
if needed.

This patch also replaced deprecated devm_reset_control_get for
mac reset.

To use this feature, the following is needed:
 1. drop "simple-mfd" compatible to register mdio0 after gmac init
    so that mdio registers aren't reset after initialization.
 2. move mdio reset from mdio-bus to its parent eth node.

NOTE: This can't be applied on gmac1 with builtin switch since we
haven't add a feature to defer probe if phy connection failed.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-05 03:02:34 +01:00
Chuanhong Guo
596a5325cd ath79: ag71xx: register mdio using of_platform_populate
remove the hacky checking of "simple-mfd" compatible
also add some comments explaining that piece of code.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-05 03:02:34 +01:00
Chuanhong Guo
f92bbdcc93 ath79: ag71xx-mdio: get reset control using devm api
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-05 03:02:34 +01:00
Chuanhong Guo
a4eef43a12 ath79: ag71xx: replace alloc_etherdev with devm_alloc_etherdev
using the devm api makes the code simpler.
also drop unneeded memory free from ag71xx_remove since they are
allocated using devm apis.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-05 03:02:34 +01:00
Chuanhong Guo
f73b2d64ed ath79: ag71xx: replace ag71xx_get_phy_if_mode_name() with phy_modes()
phy_modes() in phy.h can convert PHY modes to string with supports
for all available PHY modes.

Also add a space in mode printing to make it look better.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-05 03:02:34 +01:00
Daniel Golle
e7aa4c0db7 oxnas: pcie: model shared resource as external pcie-phy driver
Refactor pcie-oxnas to have shared resources in syscon and new pcie-phy
driver. Hopefully this revives PCIe...

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-04 23:40:43 +01:00
Daniel Golle
3bb9dcf446 oxnas: convert pcie to builtin_platform_driver
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-04 04:04:52 +01:00
Daniel Golle
302f7d57a9 oxnas: restart: use register definitions from dt-bindings
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-03 22:09:33 +01:00
Daniel Golle
dcb08049ae oxnas: cleanup and improve pcie driver
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-03 21:50:55 +01:00
Daniel Golle
c1a8054114 oxnas: add SoC restart driver for reboot
Refresh oxnas kernel config while at it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-03 02:46:05 +01:00
Daniel Golle
42f2e07ba0 oxnas: cloudengines,pogoplug*: enable USB ports
Reported-by: Jörg Fischer <fischer.loepsingen@yahoo.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-02 18:54:30 +01:00
Chris Blake
26cb167a5c mpc85xx: Fix Aerohive HiveAP-330 initramfs image
At some point our initramfs image grew over 6MB, which is
causing an issue when uncompressing in the stock bootloader:

=> bootm 0x5000000 - 0x1000000;
   Image Name:   Linux-4.19.24
   Created:      2019-02-23   1:58:20 UTC
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    6752470 Bytes =  6.4 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Booting using the fdt blob at 0x1000000
   Uncompressing Kernel Image ... Error: inflate() returned -5
GUNZIP: uncompress, out-of-mem or overwrite error - must RESET
   board to recover
   Loading Device Tree to 00ffa000, end 00fffc78 ... OK

To get around this, we need to move to an uncompressed image
for the initramfs image. While this makes a larger image, it
is thankfully bootable so people can then convert their
devices to run OpenWRT. It's worth noting the non-initramfs
image is under 3M, so it will be ages before we have any issues
with the flashed kernel.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[keep commit message at less than 75 characters per line]
2019-03-02 13:04:54 +01:00
David Bauer
6837c757cf ath79: make TP-Link revision naming consistent
This commit makes the TP-Link hardware-revision naming consistent to
match the one used by the vendor. TP-Link refers to the different
revisions as "vX" not "Version X".

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-02 13:04:54 +01:00
Kip Porterfield
f2c83532f9 ramips: add support for Belkin F9K1109v1
Device specification:
- SoC: Ralink RT3883 (MIPS 74Kc) 500Mhz
- RAM: 64Mb
- Flash: 8MB (SPI-NOR)
- Ethernet: 10/100/1000 Mbps
- WLAN
	Wireless 1: SoC-integrated : 2.4/5 GHz
	Wireless 2: 2.4 GHz RT3092L
- LED: 2x USB, WAN, LAN
- Key: WPS, reset
- Serial: 4-pin header, (57600,8,N,1), 3.3V TTL,
	GND, RX, TX, V - J12 marking on board
- USB ports: 2 x USB 2.0

Flashing instructions:

Option 1 (from bootloader web)
- Hold reset button on the back of router when plugging
  in power (for at-least 10 seconds after plugged in)
- Connect to a Lan port
- Set computer IP to 10.10.10.3
- Go to http://10.10.10.123 in a web browser
- Click the Browse... Button and select the
   *squashfs.sysupgrade.bin file then click APPLY

Option 2 (from the stock admin web)
- Go to firmware upgrade
- Upload the **factory** image *initramfs.bin first
- Boot into openwrt
- From Luci web in openwrt upload the *squashfs.sysupgrade.bin

Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added v1 to the compatible identifier, added pciid for
the RT3092L, fixed pci unit-address, split out the F9K110X.dtsi
to prepare for a possible F9K1103 patch]
2019-03-02 13:04:45 +01:00
David Santamaría Rogado
6c558bae64 ath79: TP-Link Archer C7 v4 swap usb led names
Commit 34b10b46 made usb match with the corresponding usb label.
The problem is that v4 seems to use in stock firmware the
upper led for usb 1 and the lower led for usb 2.

The led assigned varies between TP-Link models and even
same model versions. For example, Archer C7 v1 and v2 have
the leds in the reverse order.

Revert 34b10b46 and swap led labels instead, now usb port
and led label match and also respect the original behavior.

Tested-by: Oldrich Jedlicka <oldium.pro@gmail.com>
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
2019-03-02 12:59:48 +01:00
Yangbo Lu
cb911a05b0 layerscape: fix VFIO driver build issue since linux-4.14.99
The linux-4.14.99 had introduced below upstream patch.
6636dc5e01c6 arm64: io: Ensure value passed to __iormb() is held in a 64-bit register

It was causing VFIO driver build issue. This patch is to fix it.

 CC      drivers/vfio/fsl-mc/vfio_fsl_mc.o
In file included from ./include/linux/scatterlist.h:9:0,
                 from ./include/linux/iommu.h:22,
                 from drivers/vfio/fsl-mc/vfio_fsl_mc.c:14:
drivers/vfio/fsl-mc/vfio_fsl_mc.c: In function 'vfio_fsl_mc_dprc_wait_for_response':
./arch/arm64/include/asm/io.h:122:45: error: expected expression before ')' token
        : "=r" (tmp) : "r" ((unsigned long)(v))  \
                                             ^
drivers/vfio/fsl-mc/vfio_fsl_mc.c:334:3: note: in expansion of macro '__iormb'
   __iormb();
   ^~~~~~~
./arch/arm64/include/asm/io.h:122:45: error: expected expression before ')' token
        : "=r" (tmp) : "r" ((unsigned long)(v))  \
                                             ^
drivers/vfio/fsl-mc/vfio_fsl_mc.c:336:3: note: in expansion of macro '__iormb'
   __iormb();
   ^~~~~~~

Reported-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2019-03-02 12:59:48 +01:00
Christian Lamparter
ffd8ca18cc apm821xx: speed up ath9k-caldata extraction
Reading and writing to and from flash storage is slow and currently,
the ath10kcal_extract() scripts are even more at an disadvantage
because they use a block size of 1 to be able skip.

This patch reworks the extraction scripts to be much faster and
efficient by reading and writing the calibration data in possibly
one big block.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-02 12:59:48 +01:00
Dmitry Tunin
21e90685b6 ath79: speed up ath9k-eeprom extraction
This is a simple copy of ipq40xx: speed up ath10k-caldata
extraction commit a69e101ed1

Tested on DIR-825-B1

3768+0 records in
3768+0 records out
real	0m 11.90s
user	0m 0.03s
sys	0m 9.94s

1+0 records in
1+0 records out
real	0m 0.03s
user	0m 0.00s
sys	0m 0.03s

With this change eeprom extraction is fast enough to get
working Wi-Fi after initial install.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
2019-03-02 12:59:48 +01:00
Christian Lamparter
4c70ac7be4 x86: fix geode image builds redux
This patch adds more disabled DRM config symbols from the
x86' config to the generic target configs. The existing
symbols in the x86' configs are kept for now, until we
know whenever we want to remove such symbols or not
(see Github PR #1831, #1825, #1828).

THis patch also contains a squashed patch from
Daniel Engberg <daniel.engberg.lists@pyret.net> titled
"kernel: Fix config for 4.14" which fixes a duplicated line
added by: commit 8bdc241d01 ("x86: fix geode image builds")

Fixes: 8bdc241d01 ("x86: fix geode image builds")
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-02 12:59:47 +01:00
Daniel Golle
6b2874707a oxnas: switch to DTS aliases for LEDs and use generic diag.sh
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-01 23:51:19 +01:00
Daniel Golle
e2fea41ad6 oxnas: fix forgotten MTD partition name
Fixes: 858aebc0ef ("oxnas: unify MTD partition names")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-01 22:15:43 +01:00
Adrian Schmutzler
b462bab099 ath79: Fix indent
Fix wrong indentation introduced in 59c2f8a.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-03-01 09:01:45 +01:00
Daniel Golle
266b3da335 oxnas: remove uboot-oxnas-ox820 from default package selection
All supported boards should work with the $vendor bootloader just fine.
Existing users should mindfully re-flash using new initramfs build and
restore $vendor bootloader's bootcmd to it's original setting.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-01 04:09:00 +01:00
Daniel Golle
5fac36d5aa oxnas: switch to kmod-ledtrig-usb-port
Add port handles for both USB 2.0 ports so they can be used as
trigger-source for USB LEDs.
Suggestions for pogoplug and akitio,mycloud devices are welcome.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-01 04:09:00 +01:00
Daniel Golle
858aebc0ef oxnas: unify MTD partition names
Use 'u-boot' and 'u-boot-env' like the majority of OpenWrt targets
does...

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-01 03:36:32 +01:00
Daniel Golle
994428f395 oxnas: add missing NAND partitions
add kernel and other missing NAND flash partitions to allow booting
using stock loader instead of the 2nd-stage bootloader.
This will ease installation from stock firmware on pogoplugs as well
as stg212 aka. medion nas.

Existing users of OpenWrt on those boards will have to boot initramfs
generated after this commit and subsequently flash first the ubinized
image, then again run initramfs to flash sysupgrade.tar image, and
then restore bootcmd in U-Boot environment back to the original setting
('nboot 60500000 0 440000' or something like that) instead of jumping
into the now no longer used 2nd-stage loader.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-02-28 13:03:26 +01:00
INAGAKI Hiroshi
9c7fd17f4a ipq806x: fix LED configuration for NEC Aterm WG2600HP
NEC WG2600HP uses port1 on QCA8337 as a WAN port, so "0x2" should
be used as a portmask instead of "0x1e" for "WAN" LED configuration.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-02-28 11:54:09 +01:00
David Santamaría Rogado
e65f935de9 ar71xx: Change led trigger from usbdev to usbport
This patch changes all the legacy usbdev leds triggers
to the use usbport. The problem is that the usbdev triggers
get applied as usbport in sysfs but LuCI gets confused and
is not able to show the configuration with usbdev. More
information can be found in the PR:
<https://github.com/openwrt/openwrt/pull/1819>

Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[extended commit message]
2019-02-28 11:34:48 +01:00
Bart Lauret
4386054549 ath79: add support for TP-Link Archer C5 v1
TP-Link Archer C5 v1 is a dual band router
based on Qualcomm/Atheros QCA9558 + QCA9880.

Specification:

 - 720 MHz CPU
 - 128 MB of RAM (Various chips)
 - 16 MB of FLASH (Various chips)
 - SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi
 - minipcie slot with 3T3R 5 GHz QCA9880-BR4A
 - 5x 10/100/1000 Mbps Ethernet (AR8327N Switch)
 - 10x LEDs, 2x software buttons

For further informwation on the device, visit the wiki:
<https://openwrt.org/toh/tp-link/archer-c5-c7-wdr7500>

Signed-off-by: Bart Lauret <bblauret@gmail.com>
2019-02-28 11:32:55 +01:00
David Santamaría Rogado
34b10b468e ath79: TP-Link Archer C7 v4 swap usb port leds
USB 1 triggers usb2 led and USB 2 triggers usb1.
Lower LED is usb1 and upper LED usb2.

Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
2019-02-28 11:32:55 +01:00
Luo chongjun
693c8fb0e3 ath79: Modify glinet x750 and AR300m MAC address offsets
In the production of glinet, the MAC address of ethernet port is
only written at the position where the ART area offset address
is 0, and the MAC address of eth1 is added 1 on the basis of eth0.

Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
2019-02-28 11:32:55 +01:00
David Bauer
95b0c07a61 ipq40xx: add support for FritzBox 7530
Hardware
--------
CPU:   Qualcomm IPQ4019
RAM:   256M
FLASH: 128M NAND
ETH:   QCA8075
VDSL:  Intel/Lantiq VRX518 PCIe attached
       currently not supported
DECT:  Dialog SC14448
       currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED:    - Power/DSL green
        - WLAN green
        - FON/DECT green
        - Connect/WPS green
        - Info green
        - Info red
BTN:    - WLAN
        - FON
        - WPS/Connect
UART:  115200n8 3.3V (located under the Dialog chip)
       VCC - RX - TX - GND (Square is VCC)

Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
   subdirectory. Place it in the same directory as the 'eva_ramboot.py'
   script. It is located in the 'scripts/flashing' subdirectory of the
   OpenWRT tree.

2. Assign yourself the IP address 192.168.178.10/24. Connect your
   Computer to one of the boxes LAN ports.

3. Connect Power to the Box. As soon as the LAN port of your computer
   shows link, load the U-Boot to the box using following command.

   > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin

4. The U-Boot will now start. Now assign yourself the IP address
   192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
   server root directory and rename it to 'FRITZ7530.bin'.

5. The Box will now boot OpenWRT from RAM. This can take up to two
   minutes.

6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
   scp. SSH into the Box and first write the Bootloader to both previous
   kernel partitions.

   > mtd write /path/to/uboot-fritz7530.bin uboot0
   > mtd write /path/to/uboot-fritz7530.bin uboot1

7. Remove the AVM filesystem partitions to make room for our kernel +
   rootfs + overlayfs.

   > ubirmvol /dev/ubi0 --name=avm_filesys_0
   > ubirmvol /dev/ubi0 --name=avm_filesys_1

8. Flash OpenWRT peristently using sysupgrade.

   > sysupgrade -n /path/to/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:32:55 +01:00
Christian Lamparter
18e942b6c4 ipq40xx: fix pcie msi IRQ trigger level
From: Niklas Cassel <niklas.cassel@linaro.org>
|The databook clearly states that the MSI IRQ (msi_ctrl_int) is a level
|triggered interrupt.
|
|The msi_ctrl_int will be high for as long as any MSI status bit is set,
|thus the IRQ type should be set to IRQ_TYPE_LEVEL_HIGH, causing the
|IRQ handler to keep getting called, as long as any MSI status bit is set.
|[...]
|Not having the correct IRQ type defined will cause us to lose interrupts,
|which in turn causes timeouts in the PCIe endpoint drivers.
|
|Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
|Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
Christian Lamparter
46b949a067 ipq40xx: enlarge PCIe BAR size
David Bauer reported that the VDSL modem (attached via PCIe)
on his AVM Fritz!Box 7530 was complaining about not having
enough space in the BAR. A closer inspection of the old
qcom-ipq40xx.dtsi pulled from the GL-iNet repository listed:

| qcom,pcie@80000 {
|       compatible = "qcom,msm_pcie";
|       reg = <0x80000 0x2000>,
|             <0x99000 0x800>,
|             <0x40000000 0xf1d>,
|             <0x40000f20 0xa8>,
|             <0x40100000 0x1000>,
|             <0x40200000 0x100000>,
|             <0x40300000 0xd00000>;
|       reg-names = "parf", "phy", "dm_core", "elbi",
|                       "conf", "io", "bars";

Matching the reg-names with the listed reg leads to
<0xd00000> as the size for the "bars".

BugLink: https://www.mail-archive.com/openwrt-devel@lists.openwrt.org/msg45212.html
Reported-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
Christian Lamparter
ddece08bf4 kernel: owl-loader: fix sparse endian warnings
owl-loader.c:83:21: sparse: warning: incorrect type in assignment (different base types)
owl-loader.c:83:21: sparse:    expected unsigned short [usertype] reg
owl-loader.c:83:21: sparse:    got restricted __be16 const [usertype] reg
owl-loader.c:84:21: sparse: warning: incorrect type in assignment (different base types)
owl-loader.c:84:21: sparse:    expected unsigned int [usertype] val
owl-loader.c:84:21: sparse:    got restricted __be16 const [usertype] low_val
owl-loader.c:85:28: sparse: warning: restricted __be16 degrades to integer

Reported-by: kbuild test robot
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
Christian Lamparter
ca769e081f kernel: disable touchscreen symbols
This patch removes the obsolete touchscreen config symbols
and all disables all remaining ones in the generic config.

Generated by running drivers/input/touchscreen/Kconfig

 sed -n 's/^config[[:space:]]\(.*\)/# CONFIG_\1 is not set/p' Kconfig |\
 sort -d
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
Christian Lamparter
8bdc241d01 x86: fix geode image builds
This patch adds the disabled DRM_RADEON and DRM_AMDGPU
config symbols from the x86' config to the generic target
configs. The existing symbols in the x86' configs are kept
for now, until we know whenever we want to remove such
symbols or not (see Github PR #1831, #1825, #1828).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
张鹏
bbab33724d ipq40xx: add support for Qxwlan E2600AC C1 and C2
Qxwlan E2600AC C1 based on IPQ4019

Specifications:
SOC:	Qualcomm IPQ4019
DRAM:	256 MiB
FLASH:	32 MiB Winbond W25Q256
ETH:	Qualcomm QCA8075
WLAN:	5G + 5G/2.4G
	* 2T2R 2.4/5 GHz
	 - QCA4019 hw1.0 (SoC)
	* 2T2R 5 GHz
	 - QCA4019 hw1.0 (SoC)
INPUT:  Reset buutton
LED:	1x Power ,6 driven by gpio
SERIAL: UART (J5)
UUSB:	USB3.0
POWER:	1x DC jack for main power input (9-24 V)
SLOT:	Pcie (J25), sim card (J11), SD card (J51)

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Qxwlan E2600AC C2 based on IPQ4019

Specifications:
SOC:	Qualcomm IPQ4019
DRAM:	256 MiB
NOR:	16 MiB Winbond W25Q128
NAND:	128MiB Micron MT29F1G08ABAEAWP
ETH:	Qualcomm QCA8075
WLAN:	5G + 5G/2.4G
	* 2T2R 2.4/5 GHz
	 - QCA4019 hw1.0 (SoC)
	* 2T2R 5 GHz
	 - QCA4019 hw1.0 (SoC)
INPUT:  Reset buutton
LED:	1x Power, 6 driven by gpio
SERIAL: UART (J5)
USB:	USB3.0
POWER:	1x DC jack for main power input (9-24 V)
SLOT:	Pcie (J25), sim card (J11), SD card (J51)

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "ubi" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
[ added rng node. whitespace fixes, ported 02_network,
ipq-wifi Makefile, misc dts fixes, trivial message changes ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
Roger Pueyo Centelles
59c2f8af8c ath79: add support for COMFAST CF-E120A v3
This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless
CPE with two Ethernet ports and a 802.11an radio.

Specifications:

 - AR9344 SoC
 - 535/400/267 MHz (CPU/DDR/AHB)
 - 2x 10/100 Mbps Ethernet, both with PoE-in support
 - 64 MB of RAM (DDR2)
 - 8 MB of FLASH
 - 2T2R 5 GHz, up to 25 dBm
 - 11 dBi built-in antenna
 - POWER/LAN/WAN/WLAN green LEDs
 - 4x RSSI LEDs (2x red, 2x green)
 - UART (115200 8N1) and GPIO (J9) headers on PCB

Flashing instructions:

 The original firmware is based on OpenWrt so a sysupgrade image can be
 installed via the stock web GUI. Settings from the original firmware
 will be saved and restored on the new one, so a factory reset will be
 needed. To do so, once the new firmware is flashed, enter into failsafe
 mode by pressing the reset button several times during the boot
 process, while while the WAN LED flashes, until it starts flashing
 faster. Once in failsafe mode, perform a factory reset as usual.

 The U-boot bootloader contains a recovery HTTP server to upload the
 firmware. Push the reset button while powering the device on and
 keep it pressed for >10 seconds. The recovery page will be at
 http://192.168.1.1

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-02-28 11:26:10 +01:00
Marcel Jost
e6f047fa36 ramips: add TP-Link TL-WR802N-v4 support
This patch adds support for the TP-Link TL-WR802N-v4.
https://openwrt.org/toh/tp-link/tl-wr802n

Specification:
- MT7628N (580 MHz)
- 64 MB RAM
- 8 MB FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet
- 1x LED

Flash instruction:

The only way to flash the image in TL-WR802N v4 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 10 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Marcel Jost <majo@icutech.ch>
2019-02-28 11:26:10 +01:00
Thomas Vincent-Cross
a915ad8464 ramips: use generic board detection for Wavlink WL-WN575A3
Bring Wavlink WL-WN575A3 in line with other Wavlink ramips devices.

Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
2019-02-28 11:26:10 +01:00
Thomas Vincent-Cross
25c0b41901 ramips: various Wavlink WL-WN575A3 fixes
* assign pinmux groups to gpio function for LEDs/buttons
* rename flash node to be more generic in line with other device nodes
* remove useless/incorrect eeprom property from wmac node
* correct base mac address for embedded switch

Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
2019-02-28 11:26:10 +01:00
Aleksander Jan Bajkowski
00d89b4a89 sunxi: add support for Orange Pi One
CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz
GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0)
Memory: 512MB DDR3 (shared with GPU)
Onboard: Storage TF card (Max. 64GB) / MMC card slot
Onboard header: SPI, I2C, GPIO, UART
USB 2.0: One USB 2.0 HOST, One USB 2.0 OTG

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2019-02-26 23:20:04 +01:00
David Bauer
4ecf2ee4a0 ath79: fix support-list for TP-Link WDR3600
The TP-Link WDR3600 shares the same machine-code in the ar71xx target,
thus expecting "tl-wdr4300" not "tl-wdr3600" in the support-list
metadata to allow non-forced sysupgrades from ar71xx to ath79.

With this, it is possible to flash a WDR4300 image on the WDR3600. It
is no problem however, as the only difference is the 5GHz WiFi chip
which has 3SS instead of 2SS. Both work with either image.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-02-26 23:20:04 +01:00
David Bauer
5568c8a9fe ath79: add ar71xx support-list entry for Fritz4020
This adds the support-list entry the AVM FRITZ!Box 4020 expects in the
ar71xx target to allow non-forced sysupgrades from ar71xx to ath79.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-02-26 23:20:04 +01:00
Andreas Ziegler
53c46b504c ar71xx: GL.iNet AR300M family: correct LED definitions
remove USB as this is no LED but power control
rename WiFi LED with correct color red (like in stock firmware)
set middle LED to be used for LAN link/activity

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
2019-02-26 23:20:04 +01:00
Piotr Dymacz
c568c6dc09 ipq40xx: add support for ALFA Network AP120C-AC
ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm
IPQ4018 + QCA8075 platform.

Specification:

- Qualcomm IPQ4018 (717 MHz)
- 256 MB of RAM (DDR3)
- 16 MB (SPI NOR) + 128 MB (SPI NAND) of flash
- 2x Gbps Ethernet, with 802.3af PoE support in one port
- 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922)
- 3x U.FL connectors
- 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas
- Atmel/Microchip AT97SC3205T TPM module (I2C bus)
- TI CC2540 Bluetooth LE module (USB 2.0 bus)
- 4x LED (all driven by GPIO)
- 1x button (reset)
- 1x USB 2.0 (optional, not installed in indoor version)
- DC jack for main power input (12 V)
- UART header available on PCB (2.0 mm pitch)

Flash instruction:

1. This board uses dual-image feature (128 MB NAND is divided into two
   64 MB partitions: 'rootfs1' and 'rootfs2').
2. Before update, make sure your device is running firmware no older
   than v1.1 (previous versions have incompatible U-Boot).
3. Use 'factory' image in vendor GUI or for sysupgrade tool, without
   preserving settings.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-02-26 00:16:22 +01:00
Piotr Dymacz
99f72c0d62 ipq40xx: add support for Macronix MX35LF1GE4AB SPI NAND
Without a proper SPI NAND support (SPI NAND framework is available in
kernel >= 4.19) the only way to make such flash working is to include
it in raw/parallel NAND subsystem support and combine with mt29f staging
driver. Obviously, this approach isn't going to be accepted by upstream
(similar support for Winbond W25N01GV was rejected).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-02-26 00:15:38 +01:00
Koen Vandeputte
f20fea9dcd kernel: bump 4.19 to 4.19.25
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-25 17:33:16 +01:00
Koen Vandeputte
ceed0665cc kernel: bump 4.14 to 4.14.103
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-25 17:33:16 +01:00
Koen Vandeputte
151d806c78 kernel: bump 4.9 to 4.9.160
Refreshed all patches.

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-25 17:33:16 +01:00
Stijn Tintel
ffc65a80d1 kernel: add missing config symbols
The addition of kmod-input-touchscreen-ads7846 enabled
INPUT_TOUCHSCREEN, which exposes several other symbols on various
targets. Add those symbols to the generic kernel configs to fix build.

Fixes: 77a54bbf13 ("kernel: add kmod-input-touchscreen-ads7846")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-02-25 15:46:10 +02:00
Stijn Tintel
77a54bbf13 kernel: add kmod-input-touchscreen-ads7846
This module adds support for ADS7846 based touchscreens used in devices
like the WaveShare 3.5" and 4" LCD displays designed for Raspberry Pi.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-02-24 01:17:01 +02:00
Stijn Tintel
9f4a7de48a kernel: add kmod-fb-tft
This module adds support for small TFT LCD display modules. While this
module also exists in the 4.9 kernel, we are not going to support this
kernel in the next major release, so don't make it available for 4.9.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-02-24 01:15:22 +02:00
Koen Vandeputte
d9ab3240a5 kernel: bump 4.19 to 4.19.24
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-22 10:53:42 +01:00
Koen Vandeputte
3a2668c6d5 kernel: bump 4.14 to 4.14.102
Refreshed all patches.

Remove upstreamed:
- 272-uapi-if_ether.h-prevent-redefinition-of-struct-ethhd.patch

Remove upstreamed hunks:
- 080-pinctrl-msm-fix-gpio-hog-related-boot-issues.patch

Fixes:
- CVE-2018-1000026

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-22 10:53:42 +01:00
Koen Vandeputte
8f980a8cfe kernel: bump 4.9 to 4.9.159
Refreshed all patches.

Remove upstreamed:
- 023-1-smsc95xx-Use-skb_cow_head-to-deal-with-cloned-skbs.patch
- 023-6-ch9200-use-skb_cow_head-to-deal-with-cloned-skbs.patch
- 023-7-kaweth-use-skb_cow_head-to-deal-with-cloned-skbs.patch
- 050-usb-dwc2-Remove-unnecessary-kfree.patch
- 092-netfilter-nf_tables-fix-mismatch-in-big-endian-syste.patch
- 272-uapi-if_ether.h-prevent-redefinition-of-struct-ethhd.patch

Fixes:
- CVE-2018-1000026

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-22 10:53:42 +01:00
Koen Vandeputte
26f8644510 kernel: bump 3.18 to 3.18.135
Refreshed all patches.

Fixes:
- CVE-2019-3819
- CVE-2019-7221
- CVE-2019-7222

Compile-tested on: adm5120
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-22 10:53:42 +01:00
Chuanhong Guo
3bd871ad52 ath79: fix wmac memory region for qca953x
According to /arch/mips/include/asm/mach-ath79/ar71xx_regs.h
the size of wmac register range for qca953x is only 0x20000.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-02-20 18:51:31 +01:00
Linus Walleij
c72b1d8468 gemini: Generate harddisk image for DNS-313
This makes OpenWrt build an Ext2+Ext4 partitioned image
for the D-Link DNS-313 with two blank partitions, a boot
partition on /dev/sda3 and a rootfs partition on
/dev/sda4.

This uses the methods already used in apm821xx including
the tricks to convert the generated Ext2 filesystem
partition to version 1 so that the firmware bootloader
will properly recognize it.

We patch a bit around the build files to make sure we
get the rootfs size set and that genext2fs is properly
built.

Tested on the D-Link DNS-313.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[Fixing and tricksing]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-02-20 18:51:31 +01:00
Christian Lamparter
a69e101ed1 ipq40xx: speed up ath10k-caldata extraction
Reading and writing to and from flash storage is slow and currently,
the ath10kcal_extract() scripts are even more at an disadvantage
because they use a block size of 1 to be able skip.

This patch reworks the extraction scripts to be much faster and
efficient by reading and writing the calibration data in possibly
one big block.

before: (Tested on a RT-AC58U, which has SPI-NAND).

 # time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=1 skip=4096 count=12064
12064+0 records in
12064+0 records out
real    0m 0.28s
user    0m 0.02s
sys     0m 0.24s

after:

 # time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=12064 skip=4096 count=1 iflag=skip_bytes
1+0 records in
1+0 records out
real    0m 0.01s
user    0m 0.00s
sys     0m 0.00s

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-20 18:51:19 +01:00
Pawel Dembicki
02644e5612 generic: kernel: Add missing config option
DRM packages break modules compilation for sunxi target,
cortexa7 and cortexa8 subtargets.

This patch add missing symbol to generic config.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-02-19 22:11:29 +01:00
Yousong Zhou
afe00a79ee armvirt: 32: enable CONFIG_ARM_LPAE
This is required for running armvirt_32 on QEMU 3.0 [1], otherwise the
kernel will emit the following complaint and virtio-net-pci devices will
fail to be initialized

        [    1.124214] OF: PCI: host bridge /pcie@10000000 ranges:
        [    1.125093] OF: PCI:    IO 0x3eff0000..0x3effffff -> 0x00000000
        [    1.125942] OF: PCI:   MEM 0x10000000..0x3efeffff -> 0x10000000
        [    1.126403] OF: PCI:   MEM 0x8000000000..0xffffffffff -> 0x8000000000
        [    1.127748] pci-host-generic 4010000000.pcie: can't claim ECAM area [mem 0x10000000-0x1fffffff]: address conflict with /pcie@10000000 [mem 0x10000000-0x3efeffff]
        [    1.129752] pci-host-generic: probe of 4010000000.pcie failed with error -16

Running QEMU with "-M virt,highmem=off" is an option, but "highmem" was only
introduced as a default on flag since QEMU 2.5.0 and QEMU will fail and quit on
encounter of unknown flags

 [1] Armv7 guest fails to boot with qemu-3.0.0-1,
     https://bugzilla.redhat.com/show_bug.cgi?id=1633328#c5

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2019-02-19 13:13:49 +00:00
Yousong Zhou
0aedf5cfcb armvirt: 32: refresh kernel config
The diff was genereated by running the following command without
actually changing any kernel config options

	make kernel_menuconfig CONFIG_TARGET=subtarget

Here are some initial findings on the change

 - CONFIG_ARCH_OPTIONAL_KERNEL_RWX is now arch default
 - CONFIG_ARM_GIC_V3_ITS is selected by CONFIG_ARCH_VIRT
 - CONFIG_CPU_SPECTRE is select by CONFIG_CPU_V7
 - CONFIG_TIMER_OF is now a arch default
 - CONFIG_TIMER_PROBE is select by CONFIG_TIMER_OF

The following options should probably be moved to generic config

 - CONFIG_MIGRATION is a default on option
 - CONFIG_TREE_SRCU is a default on option for !PREEMPT && SMP system
 - CONFIG_RCU_NEED_SEGCBLIST

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2019-02-19 13:13:48 +00:00
Paul Wassi
d42c9ce326 kirkwood: add kernel 4.19 support
Add patches for 4.19
Drop patch 200-disable-tso, as the packet corruption was fixed in
kernel commit 3b89624ab54b9dc2d92fc08ce2670e5f19ad8ec8

Restructure the DTS for Marvell switch in 104-ea3500 and 105-ea4500
to fix DTC warning.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-17 19:22:39 +01:00
Lucian Cristian
e711fd48be x86: video: disable buildtin amdgpu DRM driver
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2019-02-17 19:22:39 +01:00
Lucian Cristian
cb3798cf3f x86: DRM: add x64 subtarget support
copy settings from generic subtarget

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2019-02-17 19:22:39 +01:00
Lucian Cristian
edb21ee3d2 x86: video: disable builtin radeon DRM driver
builtin driver can't access the /lib/firmware while booting,
module driver will be able to read and load the firmware files

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2019-02-17 19:22:39 +01:00
Yangbo Lu
5d11672d07 kernel: disable CONFIG_USB_IMX21_HCD in default for kernel 4.14
CONFIG_USB_IMX21_HCD should be handled in generic config and
module package. So moved it into generic config.
This also fixed build issue (kernel config question) of layerscape
armv8_32b since it also used ARCH_MXC.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[Deactivate CONFIG_USB_IMX21_HCD also for kernel 4.19]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-02-17 19:22:39 +01:00
Oskari Lemmela
cd1e9c88f3 sunxi: fix: A64 unstable timer
Backport A64 unstable timer patches from linux 5.1

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
[Split the single patch into the two original patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-02-17 19:22:39 +01:00
Pawel Dembicki
d5f615bf2a sunxi: add support for Sinovoip Banana Pi M2 Plus
CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz
GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0)
Memory: 1GB DDR3 (shared with GPU)
Onboard: Storage TF card (Max. 64GB) / MMC card slot
Onboard: Network 10/100M Ethernet RJ45 (Realtek RTL8211E)
Onboard: Network BT4.0/WiFi 802.11 b/g/n (Ampak AP6212)
Onboard header: SPI, I2C, GPIO, UART
USB 2.0: Two USB 2.0 HOST, One USB 2.0 OTG

Untested:
Audio, Video

Not working:
Bluetooth

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-02-17 19:22:39 +01:00
Tomasz Maciej Nowak
55b808e0c4 x86: image: add test module to bootloader
It was previously added in 546fced, which was part of "intel-microcode:
load as early as possible" series.
Unfortunately the conditionals added to GRUB config caused error on boot,
because on sysupgrade, bootloader is not updated and is left with old
features/modules. Since this module is needed for early microcode load
and transition to this needs to be done step by step, enable the test
module now, so that every newly created image has it already embedded.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-02-17 18:22:40 +01:00
Tomasz Maciej Nowak
bb0e4f9fb0 build: remove leftovers from previous x86 commits
VBoxManage is not used and the image is created with proper permisions:
0f5d0f6  image: use internal qemu-img for vmdk and vdi images drop host
         dependencies on qemu-utils and VirtualBox

Unreachable config symbols:
9e0759e  x86: merge all geode based subtargets into one

No need to define those symbols since x86_64 is subtarget of x86:
196fb76  x86: make x86_64 a subtarget instead of a standalone target

Unreachable config symbols, so remove GRUB_ROOT:
371b382  x86: remove the xen_domu subtarget

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-02-17 18:22:40 +01:00
Adrian Schmutzler
319c5d7c49 ar71xx: Fix 5 GHz MAC address for Archer C60 v2
Looks like C60 v2 needs the MAC address to be calculated
manually, while the C60 v1 gets it correctly without manual
interference.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-02-17 18:22:39 +01:00
Rosen Penev
5e8f18fef6 kernel: Remove CONFIG_UDF_NLS for kernel 4.19
kernel 4.18 removed the symbol and made NLS implicit.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2019-02-17 17:33:18 +01:00
Koen Vandeputte
ca13820d13 kernel: bump 4.19 to 4.19.23
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-15 21:53:27 +01:00
Koen Vandeputte
3967376eb7 kernel: bump 4.14 to 4.14.101
Refreshed all patches.

Fixes:
- CVE-2019-3819

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-15 21:53:27 +01:00
Oever González
c35d7f3f8a ipq40xx: fix ipq40xx_setup_macs for Linksys EA6350v3
This commit fixes the script that sets the MAC address of the LAN
switch. The LAN MAC address should be the WAN MAC address plus one.

Without this patch the WAN and the LAN interface will use the same
MAC address and an error will be generated.

With this patch all interfaces will have a different MAC address,
consecutive in the following order: WAN, LAN, radio0 and radio1.

Signed-off-by: Oever González <notengobattery@gmail.com>
2019-02-14 16:56:15 +01:00
Roman Glova
064e431575 ipq8064: Enabling sata port ipq8064 based devices
(original text here: https://patchwork.kernel.org/patch/8686761/)

On some SOCs PORTS_IMPL register value is never programmed by the BIOS
and left at zero value. Which means that no sata ports are avaiable for
software. AHCI driver used to cope up with this by fabricating the
port_map if the PORTS_IMPL register is read zero, but recent patch
broke this workaround as zero value was valid for nvme disks.
This patch adds ports-implemented dt bindings as workaround for this issue
in a way that DT can dictate the port_map incase where the SOCs does not
program it already.

This patch is equal to commits:
67f8425d0ee1 ("ipq8064: dts: force AP148 SATA port mapping")
2e7a2c91019c ("ARM: dts: qcom: Move common nodes to ipq8064-v.1.0.dtsi")
in the upstream linux kernel.

Signed-off-by: Roman Glova <roman_glova@epam.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added upstream commits, reorg' commit message]
2019-02-14 16:56:15 +01:00
INAGAKI Hiroshi
93d4439454 ath79: add support for I-O DATA WN-AC1600DGR
I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.

Specification:

- SoC:      Qualcomm Atheros QCA9557
- RAM:      128 MB
- Flash:    16 MB
- WLAN:     2.4/5 GHz
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz:   3T3R (QCA9880)
- Ethernet: 5x 10/100/1000 Mbps
  - Switch: QCA8337N
- LED/key:  6x/6x(4x buttons, 1x slide switch)
- UART:     through-hole on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AC1600DGR
2. Connect power cable to WN-AC1600DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Alternative flash instruction using initramfs image:

1. Prepare a computer and TFTP server software with the IP address
"192.168.99.8" and renamed OpenWrt initramfs image
"uImageWN-AC1600DGR"
2. Connect between WN-AC1600DGR and the computer with UART
3. Connect power cable to WN-AC1600DGR, press "4" on the serial
console and enter the U-Boot console
4. execute "tftpboot" command on the console and download initramfs
image from the TFTP server
5. execute "bootm" command and boot OpenWrt
6. On initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
7. Wait ~150 seconds to complete flashing

This commit also removes unnecessary "qca,no-eeprom" property from
the ath10k wifi node.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-02-14 16:56:15 +01:00
Santiago Piccinini
cc8bd77772 ath79: fix qca955x dual pci resource allocation
Tested with a dual pci QCA9558 board (LibreRouter v1) in three
configurations: enabling pcie0 only, pcie1 only and both enabled.

Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
2019-02-14 16:56:15 +01:00
Santiago Piccinini
eea66c3227 ath79: fix qca955x pcie0 memory size
Datasheet states that both PCI ranges are of 0x2000000 size:
0x1000_0000-0x11FF_FFF and 0x1200_0000-0x13FF_0000.

Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
2019-02-14 16:56:15 +01:00
Marius Genheimer
9ad3967f14 ipq40xx: add support for ASUS Lyra
SoC:   Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores
RAM:   256 MiB (Nanya NT5CC128M16IP-DI)
FLASH: 128 MiB (Macronix NAND)
WiFi0: Qualcomm IPQ4019 b/g/n 2x2
WiFi1: Qualcomm IPQ4019 a/n/ac 2x2
WiFi2: Qualcomm Atheros QCA9886 a/n/ac
BT:    Atheros AR3012
IN:    WPS Button, Reset Button
OUT:   RGB-LED via TI LP5523 9-channel Controller
UART:  Front of Device - 115200 N-8
       Pinout 3.3v - RX - TX - GND (Square is VCC)

Installation:
1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp.
Login credentials are identical to the Web UI.

2. Login to the device via SSH.

3. Flash the initramfs image using

> mtd-write -d linux -i openwrt-image-file

4. Power-cycle the device and wait for OpenWRT to boot.

5. From there flash the OpenWRT-sysupgrade image.

Ethernet-Ports: Although labeled identically, the port next to
the power socket is the LAN port and the other one is WAN. This
is the same behavior as in the stock firmware.

Signed-off-by: Marius Genheimer <mail@f0wl.cc>
[Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh,
reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79,
minor dts touchup, added rng to 4.19 dts]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-14 16:56:15 +01:00
Christian Lamparter
5ee9763aaa ipq40xx: ea6350v3: 4.19: enable pseudo rng support
Robert Marko made a big effort to enable the rng on all
ipq40xx for 4.19, so let's continue the quest.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-14 16:56:15 +01:00
Linus Walleij
b9a24f31a9 gemini: Name binary "bootpart.tar.gz"
This factory binary i supposed to actually be unzipped and
untarred by the user as part of the installation process
(this NAS boots from harddisk), so name it "bootpart.tar.gz"
and not "factory.bin" so it is helpful for users.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-14 16:56:15 +01:00
Daniel Engberg
b3c050c013 kernel: Add missing config option for kernel 4.19
Add CONFIG_USB_ROLE_SWITCH otherwise Octeon 4.19 fails compile

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2019-02-14 16:56:15 +01:00
Pawel Dembicki
bbe932ac16 mpc85xx: 4.19: add missing symbol
OCEDO Panda was added in b368373f, but only for
4.14 config. This patch fix 4.19 build for generic
and p2020 subtarget.

Signed-off-by: Pawel Dembicki <p.dembicki@wb.com.pl>
2019-02-14 16:56:15 +01:00
INAGAKI Hiroshi
e52ad0f919 ramips: change status LED for Buffalo WHR-G300N
Buffalo WHR-G300N has a LED for power status indication, but it is not
connected to the GPIO and cannot be controlled by the kernel. So,
WHR-G300N uses "ROUTER" LED as the system status LED instead.

This commit changes it to use "DIAG" LED insted of "ROUTER" like
WHR-G301N in ath79 target.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-02-14 16:56:15 +01:00
David Bauer
7bf6b59724 ramips: various Netgear R6120 fixes
The R6120 has no 5GHz WLAN LED, the assigned GPIO in fact controls
the WAN LED.

Renames the LED accordingly in the device-tree.
Removes the 5GHz WLAN LED trigger.
Adds the correct WAN port LED trigger.

----

Currently, the MAC address for the Netgear R6120 is read from the NVRAM
partition. The offset for the MAC address however is not consistent
across devices or firmware versions.

Switch to using the factory partition like all other Netgear devices do.

----

The LAN ports of the R6120 are labled in reverse on the casing.

Adjust LuCI switchport numbering accordingly.

----

The WiFi eeprom offsets for the R6120 are currently wrong (5GHz offset
is bigger than the partition itself).

Fixes poor performance on 2.4 and 5 GHz.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-02-14 16:56:14 +01:00
INAGAKI Hiroshi
f305ce5c35 ramips: add support for I-O DATA WN-AC1167GR
I-O DATA WN-AC1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7620A.

Specification:

- SoC     : MediaTek MT7620A
- RAM     : DDR2 64 MB
- Flash   : SPI-NOR 8MB
- WLAN    : 2.4/5 GHz, 2T2R
  - 2.4 GHz: MT7620A (SoC)
  - 5 GHz  : MT7612E
- Ethernet: 10/100/1000 Mbps (ext. MT7530)
- LED/key : 4x/3x (2x buttons, 1x slide-switch)
- UART    : through-hole on PCB
  - J2: TX, GND, RX, Vcc from SoC side
  - 115200n8

Flash instruction using factory image:

1. Boot WN-AC1167GR normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-02-14 16:56:14 +01:00
Paul Wassi
dee8db441e ath79: proper indentation in image/common-tp-link.mk
Add two spaces for proper indentation in image/common-tp-link.mk

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
212892ce70 ath79: fix port order on TL-WR841ND-v7
The switch ports are seen one to one on the case.
Also remove unneeded secondary port numbers in this
case statement.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
97fcd2622a ath79: change ledtrig on GL.iNet AR150
Change the ledtrig for LAN from netdev to switch.
Although eth1 comes out of the device at a single port,
this port is a switch-port and therefore the LED
must be triggered by that.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
79cc48ff60 ath79: rename TP-LINK to TP-Link
Remove inconsistencies in the vendor's name.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
78277ec162 ar71xx: fix TL-MR3220-v2 switch port order
Fix the switch port order for proper display on high
level interfaces.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
341311f319 ar71xx: fix TL-WR741ND-v4 switch port order
Fix the switch port order for proper display on high
level interfaces.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
ff541c5ca2 ath79: rename TL-WR740ND-v4 to TL-WR740N-v4
Give the device the same name it had in ar71xx.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
da1107f8a5 ath79: fix TL-WR741ND-v4 switch port order
Fix the switch port order for proper display on high
level interfaces.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:13 +01:00
Koen Vandeputte
6b6f238b82 kernel: bump 4.19 to 4.19.21
Refreshed all patches.

Remove upstreamed:
- 0007-ARM-dts-Fix-up-the-D-Link-DIR-685-MTD-partition-info.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-14 16:45:01 +01:00
Koen Vandeputte
9a1d7ff187 kernel: bump 4.14 to 4.14.99
Refreshed all patches.

Remove upstreamed:
- 950-0434-mmc-bcm2835-Recover-from-MMC_SEND_EXT_CSD.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-14 16:45:01 +01:00
Koen Vandeputte
a23a13dec2 kernel: bump 4.9 to 4.9.156
Refreshed all patches.

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-14 16:45:01 +01:00
Tony Ambardar
a7370b5179 kernel: enable CONFIG_BPF_JIT by default
Enable the built-in BPF JIT compiler for all 4.9, 4.14 and 4.19 kernels,
which should speed up cBPF and eBPF-based packet filtering (tc, iptables)
and packet sniffing (libpcap, tcpdump, fwknopd, etc).

This has minimal kernel size impact, increasing the size of uImage-lzma
(normally ~2 MB on mips_24kc or mips64el_mips64) by 5 KB for the MIPS32
arch cBPF JIT and by 9 KB for the MIPS64 arch eBPF JIT, on kernel 4.14.

With JIT enabled (cBPF only), the standard BPF test module (test_bpf.ko)
running on a DIR-835 (mips_24kc) used 33 CPU seconds, but 68 without JIT.

This change aligns with the notion of OpenWRT as the network go-to swiss
army knife for packet handling, especially on CPU-constrained platforms.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2019-02-11 20:18:48 +00:00
David Bauer
0c24b363a6 ath79: add support for Xiaomi Mi Router 4Q
Hardware
--------
CPU:   Qualcomm Atheros QCA9561
RAM:   64M DDR2
FLASH: 16M SPI-NOR
ETH:   1x WAN - 2x LAN
WiFi:  QCA9561 3T3R
BTN:   1x Reset - 1x WPS
LED:   1x Blue - 1x Red - 1x Yellow
UART:  TX - GND - RX - VCC (From ethernet port)
       115200n8 - 3.3V

Installation
------------
1. Connect to the device via UART.

2. Interrupt the U-Boot on power-on by pressing enter when prompted.

3. Connect you computer to one of the routers LAN ports.
   Assign yourself the IP 192.168.31.10/24.
   Copy the OpenWRT initramfs image to a tftp server root directory.
   Rename the image to 'x4q.bin'.

4. Load the initramfs image to the router by executing following command
   in U-Boot. The image will boot afterwards.

   > tftpboot 0x81000000 x4q.bin; bootm

5. SCP the sysupgrade-image into '/tmp'.
   Remember to assign yourself an IP in 192.168.1.0/24 for this step!

6. Install OpenWRT permanently by executing

   > sysupgrade -n /tmp/<OpenWRT-sysupgrade-image>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-02-11 19:04:06 +01:00
Linus Walleij
4130e24326 gemini: Fix kmod-led-trig-heartbeat typo
It's kmod-ledtrig-* not kmod-led-trig-*.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[extended subject]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-11 19:02:42 +01:00
Koen Vandeputte
8c9f255ce5 ar71xx: add rssileds for xw devices
Commit 7ebbbda293 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication")
adds support for using the RSSI strenght via LEDS.

The rssileds package addition got lost during altering the patch.
Add it again to fix this.

Fixes: 7ebbbda293 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-11 09:24:11 +01:00
Felix Fietkau
945bcaf6ec kernel: fold xt_FLOWOFFLOAD fixes into the main patch
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-02-09 14:37:30 +01:00
HsiuWen Yen
33b690216e netfilter: fix checking method of conntrack helper
This patch uses nfct_help() to detect whether an established connection
needs conntrack helper instead of using test_bit(IPS_HELPER_BIT,
&ct->status).

The reason for this modification is that IPS_HELPER_BIT is only set when
the conntrack helper is attached by explicit CT target.

However, in the case that a device enables conntrack helper via the other
ways (e.g., command "echo 1 > /proc/sys/net/netfilter/nf_conntrack_helper")
, the status of IPS_HELPER_BIT will not present any change. That means the
IPS_HELPER_BIT might lose the checking ability in the context.

Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
2019-02-09 14:37:26 +01:00
Lech Perczak
7ebbbda293 ar71xx: ubnt-(xm,xw): fix LED RSSI indication
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti XM and XW family, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.

Also add the required package for this.

While at that, remove coefficients needed for PWM LEDs, as XM and XW
boards do not support PWM LEDs.

Tested-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[Squashed commits + remove custom device_packages + slighty rewrite the commit msg]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-08 17:27:47 +01:00
Julien Rabier
6570f3c93a ar71xx: fix RB941-2nD detection
Some hAP lite routers aren't detected because
/proc/cpuinfo shows "RouterBOARD RB941-2nD"
instead of "RouterBOARD 941-2nD".

Fix that.

Signed-off-by: Julien Rabier <taziden@flexiden.org>
[Alter string to include all flavours + slight rewrite of commit msg]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-08 17:27:47 +01:00
Edoardo Scaglia
077253dd66 ar71xx: fix Arduino Yun enabling of level shifters outputs
As show in Arduino Yun schematic [1] GPIO 21 and 22 are connected to
output enable pin (OE) of two NTB01xx level shifters.

NTB01xx datasheets [2] [3] states that OE pin are active-high
therefore we should initialize GPIO 21 (DS_GPIO_OE) and GPIO 22
(DS_GPIO_OE2) accordingly to actually enable level shifters outputs.

[1] https://www.arduino.cc/en/uploads/Main/arduino-Yun-schematic.pdf
[2] https://www.nxp.com/docs/en/data-sheet/NTB0102.pdf
[3] https://www.nxp.com/docs/en/data-sheet/NTB0104.pdf

Signed-off-by: Edoardo Scaglia <edoardo.87@gmail.com>
2019-02-08 17:27:47 +01:00
Petr Štetiar
07e6ce4606 kernel: add missing symbols to 4.19
While preparing 4.19 for imx6 and test building it with
CONFIG_ALL_KMODS=y with verbose mode enabled, I was asked by kernel
config about few missing symbols/modules

Let's add them to the generic config.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[slight rewrite of commit log]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-08 17:27:47 +01:00
Koen Vandeputte
9a3599de2c kernel: bump 4.19 to 4.19.20
Refreshed all patches.

Remove upstreamed:
- 100-arm-cns3xxx-fix-writing-to-wrong-PCI-registers-after.patch

Altered patches:
- 721-phy_packets.patch

Compile-tested on: imx6
Runtime-tested on: imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-08 17:27:47 +01:00
Koen Vandeputte
89bf16ad50 kernel: bump 4.14 to 4.14.98
Refreshed all patches.

Remove upstreamed:
- 100-arm-cns3xxx-fix-writing-to-wrong-PCI-registers-after.patch

Altered patches:
- 721-phy_packets.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-08 17:27:47 +01:00
Koen Vandeputte
34e80b5d3b kernel: bump 4.9 to 4.9.155
Refreshed all patches.

Remove upstreamed:
- 100-arm-cns3xxx-fix-writing-to-wrong-PCI-registers-after.patch

Altered patches:
- 721-phy_packets.patch

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-08 17:27:47 +01:00
Petr Štetiar
5fd68d60e4 ath79: ag71xx: Fix tx queue timeouts during ifup
On ath79 and UBNT Bullet M XW (ar9342) I was experiencing weird issues during
network setup[1] which I was able to reproduce easily with following commands:

 uci set network.lan.ipaddr='192.168.1.20'
 uci commit network
 ifup lan

Which resulted after some time in:

 ...
 WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:461 dev_watchdog+0x16c/0x280
 NETDEV WATCHDOG: eth0 (ag71xx): transmit queue 0 timed out
 ...

Sometimes I wasn't able to use networking anymore, sometimes it was enough to
just ifdown/ifup lan and network was backup. On ar71xx it was all working just
fine.

I've found out, that it was happening because ag71xx_poll() wasn't called, thus
the TX queue wasn't emptied. The ag71xx_poll() is being called from napi
hrtimer, which is enabled by napi_schedule() in ar71xx_interrupt(), but since
no interrupts were ever fired again after ag71xx_stop() was called, it was
always leading to tx queue timeouts:

 *** ag71xx_hard_start_xmit()
 eth0: packet injected into TX queue
 eth0: raw intr=00000001 TXPS POLL
 eth0: enable polling mode
 eth0: processing TX ring, flush=no
 eth0: disable polling mode, rx=1, tx=1,limit=32

 ( `ifup lan done here` )

 *** ag71xx_stop()
 *** ag71xx_open()
 *** ag71xx_hw_enable()
 IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
 IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
 *** ag71xx_hard_start_xmit()
 eth0: packet injected into TX queue
 *** ag71xx_hard_start_xmit()
 eth0: packet injected into TX queue
 ...
 WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x164/0x274

So I've looked at ag71xx_stop() in ar71xx, added the missing bits to ath79 and
fixed this issue.

1. https://github.com/openwrt/openwrt/pull/1635#issuecomment-448638246

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[move ag->link before ag71xx_hw_disable to retain ordering as original]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-07 14:19:46 +01:00
Koen Vandeputte
ab18540d11 kernel: rename symbol in kernel 4.19 config
A symbol was renamed upstream starting from kernel 4.18 [1]

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?h=v5.0-rc5&id=34b13e5e4641c0e9e0aad471a6d8dfb7999276f1
2019-02-07 13:06:23 +01:00
Stijn Tintel
26fcc937f7 brcm2708: fix early bootloader config restore
Restoring the bootloader config before rebooting fails:
tar: invalid tar magic

Add the -z option to the tar command to fix this.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-02-06 07:39:39 +02:00
Stijn Tintel
c30f7f402f brcm2708: drop 4.9 support
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-02-06 07:39:39 +02:00
Oldřich Jedlička
12310f05b7 ath79: add support for TP-LINK Archer C7 v4
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on the
Qualcomm/Atheros QCA9561 SoC + QCA9880.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
   via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
   and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
   the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
2019-02-05 19:37:31 +01:00
Chuanhong Guo
be2b61e4f1 ramips: drop m25p,chunked-io from dts
This option was a spi nor hack which is dropped in commit
bcf4a5f474 ("ramips: remove chunked-io patch and set spi->max_transfer_size instead")

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [edit message]
2019-02-05 19:37:30 +01:00
Deng Qingfang
6621da55b7 ramips: enable MT7610E 5GHz radio of MT7620a_MT7610e EVB
This enables MT7610E of the EVB

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-02-05 19:37:30 +01:00
Ju Se Hoon
9f90074db7 ramips: add kmod-mt76x2 to WeVo 11AC NAS
The WeVo 11AC NAS has a MT7612E 802.11ac chip on the PCB.

Signed-off-by: Ju Se Hoon <joosahoon@gmail.com>
[renamed author from Albis-dev to real name, editted commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-05 19:37:30 +01:00
Petr Štetiar
dd3ec40d3d ramips: dts: Unify naming of gpio-led nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-02-05 16:28:12 +01:00
Petr Štetiar
e8eaf794ec ramips: dts: Unify naming of gpio-keys nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-02-05 16:28:12 +01:00
Christian Lamparter
d753a3ef0e ipq40xx: fix ASUS RT-AC58U switch port numbering
This patch fixes the ASUS' RT-AC58U port order by
unifying the configuration with the NBG6617.

Reported-by: Roberto Socrates (rtac58u-user on the forum)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-05 16:28:12 +01:00
Christian Lamparter
775258c128 ipq40xx: consolidate 02_network board defaults
This patch splits the big board case switch in 02_network in
two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs()
just like ath79 and ramips do.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-05 16:28:12 +01:00
Petr Štetiar
65f9e52526 brcm63xx: dts: Unify naming of gpio-led nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-02-05 16:28:12 +01:00
Petr Štetiar
4b66f55bb1 brcm63xx: dts: Unify naming of gpio-keys nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-02-05 16:28:12 +01:00
Koen Vandeputte
3da230a2e6 kernel: bump 4.19 to 4.19.19
Refreshed all patches.

Remove upstreamed patch:
- 800-v5.0-usb-leds-fix-regression-in-usbport-led-trigger.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-01 11:41:00 +01:00
Koen Vandeputte
206bebcad4 kernel: bump 4.14 to 4.14.97
Refreshed all patches.

Adapted patches:
- 012-kbuild-add-macro-for-controlling-warnings-to-linux-c.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-01 11:41:00 +01:00
Koen Vandeputte
604eb94550 kernel: bump 4.9 to 4.9.154
Refreshed all patches.

Adapted patches:
- 012-kbuild-add-macro-for-controlling-warnings-to-linux-c.patch

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-01 11:41:00 +01:00
Rafał Miłecki
9687cc8556 bcm53xx: add first DTS changes queued for the Linux 5.1
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-02-01 07:09:27 +01:00
Anton Arapov
ae0a40d68d ramips: rb750gr3: License DTS as GPL-2.0-or-later OR MIT
Adding license in order to fully satisfy dts checklist:
- https://openwrt.org/submitting-patches#dts_checklist

Signed-off-by: Anton Arapov <arapov@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Thibaut <hacks@slashdirt.org>
Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Acked-by: Chuanhong Guo <gch981213@gmail.com>
Acked-by: Andrew Yong <me@ndoo.sg>
Acked-by: Alex Maclean <monkeh@monkeh.net>
2019-02-01 06:35:13 +01:00
Mirko Parthey
555ca422d1 ramips: fix D-Link DIR-615 H1 switch port mapping
Reuse a device-specific switch port mapping which also applies to the
D-Link DIR-615 H1.

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
2019-01-30 13:31:43 +01:00
Jo-Philipp Wich
19850b639e ar71xx: fix packed-not-aligned error with GCC 8.
Building ar71xx currently fails with:

    In file included from ./include/linux/ipv6.h:5,
                     from ./include/net/ipv6.h:16,
                     from ./include/net/inetpeer.h:16,
                     from ./include/net/ip_fib.h:24,
                     from ./include/net/switchdev.h:17,
                     from ./include/net/dsa.h:23,
                     from arch/mips/ath79/dev-dsa.h:15,
                     from arch/mips/ath79/dev-dsa.c:17:
    ./include/uapi/linux/ipv6.h:107:1: error: alignment 1 of 'struct ipv6_destopt_hao' is less than 2 [-Werror=packed-not-aligned]
     } __attribute__((packed));

Address this issue by correcting the alignment of the struct packing
pragma accordingly.

Fixes: FS#1805
Reported-by: Pascal Ernster <git@hardfalcon.net>
[reword subject, rewrap commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-01-30 12:49:36 +01:00
David Santamaría Rogado
4bcf581352 ar71xx: use correct wan mac address for the TP-Link Archer C7 v4
The correct MAC address for this device is lan_mac +1, there is no
need to set lan_mac so use base_mac variable instead lan_mac.

Based on this PR for ath79:
https://github.com/openwrt/openwrt/pull/1726

Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
[fix alphabetical ordering, reword subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-01-30 12:24:07 +01:00
Felix Fietkau
01895c315f ramips: move wifi related interrupts off the main core on SMP systems
Improves LAN<->WLAN bridging/routing performance

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-01-29 11:27:02 +01:00
Hauke Mehrtens
a5269ffa7a kernel: Add missing config option for kernel 4.14
Kernel 4.14.96 got the new configuration option
CIFS_ALLOW_INSECURE_LEGACY which allows to deactivate support for old
and insecure SMB versions like 1.0 and 2.0. Still allow these old SMB
version and fix build problems which occurred because this option was
not defined.

This was found by build bot.

Fixes: 3662157d8b ("kernel: bump 4.14 to 4.14.96")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-28 21:39:35 +01:00
Koen Vandeputte
ca1b93f038 imx6: add support for kernel 4.19
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-28 18:17:32 +01:00
Koen Vandeputte
f003d732d7 kernel: bump 4.19 to 4.19.18
Refreshed all patches.

Removed upstreamed:
- 031-v5.0-MIPS-BCM47XX-Setup-struct-device-for-the-SoC.patch
- 142-jffs2-Fix-use-of-uninitialized-delayed_work-lockdep-.patch

Removed upstreamed hunk in:
- 800-bcma-get-SoC-device-struct-copy-its-DMA-params-to-th.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-28 18:17:32 +01:00
Koen Vandeputte
880a4b334e cns3xxx: don't use invalid mask value for clock events
According to a commit from kernel 4.18-rc3, it's not valid
to use "cpu_mask_all" for clock events and it should be
replaced in favor of "cpu_possible_mask" [1]

This warning was seen when booting kernel 4.19 on a cns3xxx board.
Let's fix it also here just to be safe.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.19.18&id=fbfa9260085b5b578a049a90135e5c51928c5f7f

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-28 18:17:32 +01:00
Koen Vandeputte
c6bebe1a94 cns3xxx: add support for kernel 4.19
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-28 18:17:32 +01:00
Koen Vandeputte
037800270b cns3xxx: use actual size reads for PCIe (4.19)
upstream commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
reimplemented cns3xxx_pci_read_config() using pci_generic_config_read32(),
which preserved the property of only doing 32-bit reads.

It also replaced cns3xxx_pci_write_config() with pci_generic_config_write(),
so it changed writes from always being 32 bits to being the actual size,
which works just fine.

Due to:
- The documentation does not mention that only 32 bit access is allowed.
- Writes are already executed using the actual size
- Extensive testing shows that 8b, 16b and 32b reads work as intended

It makes perfectly sense to also swap 32 bit reading in favor of actual size.

also backport this patch to kernel 4.19

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-28 18:17:32 +01:00
Koen Vandeputte
9a8db2d6bf cns3xxx: refresh kernel config
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-28 18:17:32 +01:00
Koen Vandeputte
3662157d8b kernel: bump 4.14 to 4.14.96
Refreshed all patches.

Remove upstreamed patches:
- 142-jffs2-Fix-use-of-uninitialized-delayed_work-lockdep-.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-28 18:17:32 +01:00
Koen Vandeputte
662b926146 kernel: bump 4.9 to 4.9.153
Refreshed all patches.

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-28 18:17:32 +01:00
Koen Vandeputte
aa95bdd80f kernel: bump 3.18 to 3.18.133
Refreshed all patches.

Compile-tested on: adm5120
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-28 18:17:32 +01:00
Hauke Mehrtens
50b3044eeb brcm2708: Fix kmod-regmap split
There are more regmap dependencies missing in the brcm2708 target.

Fixes: fd5c168701 ("kernel: Build: Split kmod-regmap")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-27 19:35:46 +01:00
Skirmantas Lauzikas
9c01273e5e ath79: add support for TP-Link Archer C2 V3 (AC900)
This commit adds support for the TP-link Archer C2 V3 (AC900).

Specifications:

 - CPU: QCA9563 750Mhz
 - Ram: 64MB (DDR2)
 - Flash: 8MB (SPI NOR)
 - Ethernet: 5x 10/100/1000
 - Wifi: QCA9563 bgn + QCA9887 an+ac
 - 9x Leds, 2x buttons

Flash instructions:

Upload openwrt-ath79-generic-tplink_archer-c2-v3-squashfs-factory.bin
via the router Web interface and flash as normal firmware update.

Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt>
[reorder entries, fix trailing whitespace in dts, add firmware partition
 compatible string, remove led default off states, use default on state
 for system led, reuse tplink-safeloader-uimage image build recipe, squash
 with dynamic partitioning commit, reword commit message, add
 installation instructions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-01-27 16:41:10 +01:00
Daniel Gonzalez Cabanelas
5af04f0d94 brcm63xx: VH4032N: add missing pinctrl
Add missing pin controls for the Observa VH4032N router.

This fixes the wifi radio and ethernet LAN LEDs.

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2019-01-27 11:52:24 +01:00
Daniel Gonzalez Cabanelas
6b2b35e043 brcm63xx: VH4032N: fix the power led and the wlan button
- use the blue LED for power, since the red LED is already used by
  CFE in emergency mode.
- use the correct code for the wlan button

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2019-01-27 11:52:24 +01:00
Hauke Mehrtens
9b47e4c007 brcm2708: Move kmod-sound-soc-3dlab-nano-player to sound modules
kmod-sound-soc-3dlab-nano-player was in the global kernel menu before,
add the dependency to sound to move it to the correct category.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-27 11:08:46 +01:00
Hauke Mehrtens
fcbbec8eb2 kernel: Fix kmod-regmap split
Two regmap dependencies were wrong, this patch fixes them.
This was detected by the build bots.

Fixes: fd5c168701 ("kernel: Build: Split kmod-regmap")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-27 11:07:14 +01:00
Martin Schiller
654124b1af lantiq/led_dsl: Fix netdev led trigger
In the upstream netdev led trigger the one mode file was replaced by 3
files named rx, tx and link. Fix the netdev trigger configuration code
to use the modified API.

This fix is based on 201058b35c ("base-files: Fix netdev led trigger")

Fixes: aa3b6a08c5 ("kernel: Replace ledtrig-netdev with upstream backport")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-01-27 01:04:53 +01:00
Daniel Engberg
be1d70e0a2 sunxi: Add support for SY8106A voltage regulator
Add support for Silergy SY8106A voltage regulator which is
needed for cpufreq support on boards such as Orange Pi PC

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[Remove CONFIG_REGULATOR_SY8106A from cortexa7]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-27 01:04:52 +01:00
Tomasz Maciej Nowak
7d188fb4db mvebu: backport upstream fixes for armada 37xx
Upstream patches for processor frequency scaling, which fix possible
system hard lockups.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-01-27 00:16:14 +01:00
Tomasz Maciej Nowak
9b1102416f mvebu: espressobin: correct spi node in dts
Drop customizations in:
508-arm64-dts-armada-3720-espressobin-wire-up-spi-flash.patch
and move them to separate patch, with broader explanation.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-01-27 00:16:14 +01:00
Tomasz Maciej Nowak
b004835908 mvebu: sort armada 37xx upstream patches chronologically
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-01-27 00:16:14 +01:00
Tomasz Maciej Nowak
9f6c4ba25c mvebu: move HARDEN_BRANCH_PREDICTOR to common config
This symbol is enabled in all subtargets, move it to common kernel
config.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Acked-by: Rosen Penev <rosenp@gmail.com>
2019-01-27 00:16:14 +01:00
Hauke Mehrtens
fd5c168701 kernel: Build: Split kmod-regmap
This reduces the needed modifications to the mainline Linux kernel and
also makes the regmap package work with an out of tree kernel which
does not have these modifications.

The regmap-core is only added when it is really build as a module.
The regmap-core is normally bool so it cannot be built as a module in an
unmodified kernel. When it is selected by on other kernel module it will
always be selected as build in and it also does not show up in
$(LINUX_DIR)/modules.builtin as it is not supposed to be a kernel module.
When it is not in $(LINUX_DIR)/modules.builtin the build system expects
it to be built as a .ko file.
Just check if the module is really there and only add it in that case.

This splits the regmap package into multiple packages, one for each bus type.
This way only the bus maps which are really needed have to be added.
This also splits the I2C, SPI and MMIO regmap into separate packages to not
require all these subsystems to build them, on an unmodified upstream kernel
this also causes problems in some situations.

Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
2019-01-27 00:16:13 +01:00
Oskari Lemmela
538127cf98 sunxi: spi flash dts changes
Backport A64 SPI flash DTS changes to 4.14 kernel.

Add Openwrt specific flash partitions to Sopine.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2019-01-26 23:11:49 +01:00
Oskari Lemmela
72102b11b8 sunxi: add spi flash support to kernel
Some of sunxi devices have onboard SPI flash.
Enable SPI NOR support and MTD fit split in kernel config.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2019-01-26 23:11:49 +01:00
Oskari Lemmela
7f06db06f2 sunxi: add a64 watchdog support
Backport A64 watchdog DTS change to 4.14 kernel.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2019-01-26 23:11:49 +01:00
Django Armstrong
1c2f7b5115 ath79: add support for Devolo WiFi Pro 1750e
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
       1x Atheros AR8033
WiFi2: QCA9558 3T3R (SiGE SE2565T 2.4 GHz power amp x3)
WiFi5: QCA9880 3T3R (Skyworks 5003L1 5 GHz power amp x3)
BTN:   1x Reset
       1x WPS
       1x USB eject
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is pin closest to rear ports)
       Dupont 4 pin header
       Rear RJ45 serial port non-functional
USB:   1x v2.0

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password previously set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: Django Armstrong <iamdjango@hotmail.com>
2019-01-26 21:46:33 +01:00
Mathias Kresin
2a4e756085 ramips: rt3883: drop jimage support
The splitter isn't required by any of the boards in the subtarget.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 21:46:33 +01:00
Mathias Kresin
8293aec943 ramips: disable CONFIG_MTD_SPLIT_FIRMWARE
It's no longer needed as all mt7621 devices use DT binding (supported by
upstream mtd code) for specifying "firmware" part format explicitly.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 21:46:33 +01:00
Rafał Miłecki
acd790c150 ramips: specify "firmware" partition format for remaining devices
It results in calling the right MTD parser directly instead of trying
them one by one.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
[use the lzma splitter for the AR670W]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 21:46:33 +01:00
Linus Walleij
11e9577511 gemini: Add a config for kernel v4.19
This adds a config for kernel v4.19 to the Gemini
target.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-01-26 21:46:33 +01:00
Linus Walleij
e44d1e17da gemini: Add v4.19 kernel patches
This is the remainder of kernel patches for the v4.19
kernel. A whole slew of the previous patch stack is now
upstream, so this mainly contains the stuff that was
added upstream between v4.19 and v5.0-rc1, and then
the USB FOTG201 patches from Hans.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-01-26 21:46:32 +01:00
David Bauer
01dcd574a2 ramips: add support for Archer C50 v4
This adds support for the TP-Link Archer C50 v4.
It uses the same hardware as the v3 variant, sharing the same FCC-ID.

CPU:   MediaTek MT7628 (580MHz)
RAM:   64M DDR2
FLASH: 8M SPI
WiFi:  2.4GHz 2x2 MT7628 b/g/n integrated
WiFI:  5GHz 2x2 MT7612 a/n/ac
ETH:   1x WAN 4x LAN
LED:   Power, WiFi2, WiFi5, LAN, WAN, WPS
BTN:   WPS/WiFi, RESET
UART:  Near ETH ports, 115200 8n1, TP-Link pinout

Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.

Download a TP-Link image from their Wesite and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:

TP-Link image:             tpl.bin
OpenWRT sysupgrade image:  owrt.bin

 > dd if=tpl.bin of=boot.bin bs=131584 count=1
 > cat owrt.bin >> boot.bin

Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.

Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.

Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.

The boot.bin can now be uploaded and flashed using the web-recovery.

Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)

 > dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
 > dd if=tpl.bin of=tmp.bin bs=131584 count=1
 > dd if=tmp.bin of=boot.bin bs=512 skip=1
 > cat boot.bin >> tp_recovery.bin
 > cat owrt.bin >> tp_recovery.bin

Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.

Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.

U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.

Dual U-Boot
-----------
This is the first TP-Link MediaTek device to feature a split-uboot
design. The first (factory-uboot) provides recovery via TFTP and HTTP,
jumping straight into the second (firmware-uboot) if no recovery needs
to be performed. The firmware-uboot unpacks and executed the kernel.

Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5. Stock-firmware sets a flag in the "romfile" partition
before beginning to write and removes it afterwards. If the router boots
with this flag set, bootloader will automatically start Web-recovery and
listens on 192.168.0.1. This way, the vendor-firmware or an OpenWRT
factory image can be written.

By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.

It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 21:46:32 +01:00
Christian Lamparter
53cc74bfa7 gemini: dlink-dir-685: fix rt2800-pci package name
The package is now called kmod-rt2800-pci.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-26 21:43:17 +01:00
Oever González
a873b29284 ipq40xx: add support for Linksys EA6350v3
Specifications:
SOC: Qualcomm IPQ4018
RAM: 256 MiB Samsung K4B2G1646F-BYK0
FLASH1: MX25L1605D 2 MB
FLASH2: Winbond W25N01GV 128Mb
ETH: Qualcomm QCA8075
WLAN0: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN1: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: WPS, Reset
LED: Status - Green
SERIAL: Header at J19, Beneath DC Power Jack
        1-VCC ; 2-TX ; 3-RX; 4-GND;
        Serial 115200-8-N-1.

Tested and working:
- USB (requires extra packages)
- LAN Ethernet (Correct MAC-address)
- WAN Ethernet (Correct MAC-address)
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from Web UI
- OpenWRT sysupgrade
- LED
- Reset Button

Need Testing:
- WPS button

Install via Web UI:
- Attach to a LAN port on the router.
- Connect to the Linksys Smart WiFi Page (default 192.168.1.1) and login
- Select the connectivity tab on the left
- In the manual update box on the right
- Select browse, and browse to
  openwrt-ipq40xx-linksys_ea6350v3-squashfs-factory.bin
- Click update.
- Read and accept the warning
- The router LED will start blinking. When the router LED goes solid, you
  can now navigate to 192.168.1.1 to your new OpenWrt installation.

Sysupgrade:
- Flash the sysupgrade image as usual. Please: try to do a reset everytime
  you can (doing it with LuCI is easy and can be done in the same step).

Recovery (Automatic):
- If the device fails to boot after install or upgrade, whilst the unit is
  turned on:
1 - Wait 15 seconds
2 - Switch Off and Wait 10 seconds
3 - Switch on
4 - Repeat steps 1 to 3, 3 times then go to 5.
5 - U-boot will have now erased the failed update and switched back to the
    last working firmware - you should be able to access your router on
    LAN.

Recovery (Manual):
- The steps for manual recovery are the same as the generic u-boot tftp
  client method.

Back To Stock:
- Use the generic recovery using the tftp client method to flash the
  "civic.img". Also you can strip-and-pad the original image and use
  the generic "mtd" method by flashing over the "kernel" partition.
* Just be careful to flash in the partition that the device is currently
  booted.

Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
[minor edits, removed second compatible of nand, added dtb entry to 4.19]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-26 21:43:11 +01:00
Petr Štetiar
89afabf9f8 ath79: dts: Unify naming of gpio-led nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[split up, removed entries where it could clash due to ath9k-leds]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-26 21:09:12 +01:00
Petr Štetiar
a012b3dfa8 ath79: dts: Unify naming of gpio-keys nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-01-26 21:09:12 +01:00
Deng Qingfang
c2bcdabf2a ramips: fix support for MX25L25635F flash
Patch picked from commit 82618062cf

This enables 4B opcodes for MX25L25635F, to fix the reboot crash
issue (FS#1120) At least 3 devices are using this flash
- GeHua GHL-R-001
- Youku YK1
- Newifi D1

Now the MX25L25635F can be correctly detected without breaking MX25L25635E
[ 3.034324] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 3.045962] m25p80 spi0.0: mx25l25635f (32768 Kbytes)
[ 3.056098] 4 fixed-partitions partitions found on MTD device spi0.0
[ 3.068748] Creating 4 MTD partitions on "spi0.0":

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added deprecation notice]
2019-01-26 17:10:19 +01:00
David Bauer
b368373fab mpc85xx: add support for OCEDO Panda
CPU:   FSL P1020 (2x 800MHz E500 PPC)
RAM:   1GB DDR3
FLASH: 256MiB NAND
WiFi:  2x Atheros AR9382 2x2:2 abgn
ETH:   2x BCM54616S - 1x BCM53128 8-port switch
LED:   5x LEDs (Power, WiFi1, WiFi2, N/D, SYS)
BTN:   1x RESET

Installation
------------

1. Download initrams kernel image, dtb binary and sysupgrade image.

2. Place initramfs kernel into tftp root directory. Rename to
"panda-uimage-factory".

3. Place dtb binary into tftp root directory. Rename to "panda.fdt".

4. Start tftp server on 192.168.100.8/24.

5. Power up the device with the reset button pressed. It will download
the initrams and dtb via tftp and boot into OpenWRT in RAM.

6. SSH into the device and remove the factory partitions.

 > ubirmvol /dev/ubi0 --name=kernel1
 > ubirmvol /dev/ubi0 --name=rootfs1
 > ubirmvol /dev/ubi0 --name=devicetree1

You will have around 60 MiB of free space with that.

You can also delete "kernel2", "devicetree2", "rootfs2" and "storage"
respectively in case you do not want to go back to the vendor firmware.

7. Modify the U-Boot bootcmd to allow for booting OpenWRT

 > fw_setenv bootcmd_owrt "ubi part ubi && ubi read 0x1000000 kernel
   && bootm 0x1000000"

 > fw_setenv bootargs_owrt "setenv bootargs console=ttyS0,115200
   ubi.mtd=3,2048"

 > fw_setenv bootcmd "run bootargs_owrt; run bootcmd_owrt"

8. Transfer the sysupgrade image via scp into the /tmp directory.

9. Upgrade the device

 > sysupgrade -n /tmp/<imagename>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 17:10:19 +01:00
David Bauer
90bfbed7c2 mpc85xx: use generic diag.sh
This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.

This way, we are also able to use different LEDs to indicate different
states. We use green status LEDs for indicating boot and a running
system. Where possible, the red status LED is used to indicate failsafe
mode and a running upgrade.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 17:10:19 +01:00
Christian Lamparter
b2e1333de3 ipq40xx: 4.19: fix pcie wifi unit-address of the MR33 and A62
The unit address should be wifi@1,0 since the device is located
at 0000:01:00.0.

Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-26 17:10:19 +01:00
Mathias Kresin
1f0e08cf95 gemini: add EOD marker to rootfs images
With 6409b159e8 ("gemini: switch to 4.14") the EOF marker were dropped
from the rootfs images. Without the marker the rootfs_data partition
can't be created and it isn't possible to permanently store any
configuration changes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:38 +01:00
Mathias Kresin
82c7699dd8 gemini: fix ITian Square One SQ201 package selection
All kernel modules are prefixed with kmod-. Add the prefix to include
the desired packages.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:38 +01:00
Mathias Kresin
a565659c29 gemini: replace date placeholder
Replace the data placerholder in ImageInfo-itian_sq201 in a reproducible
way.

The code for the replace was accidentality dropped in 5bac623895
("gemini: unify and fix ib-nas4220b and sq201 image creation")

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:38 +01:00
Mathias Kresin
67d39c03ec gemini: drop Teltonika RUT1xx artifacts
Support for the Teltonika RUT1xx was added with the switch to kernel
4.4. Hidding such changes in a kernel switch commit is the wrong way and
the support for the Teltonika RUT1xx is pretty much incomplete.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:38 +01:00
Mathias Kresin
2a8fe45df5 gemini: add wiligear image build code
They were dropped with 6409b159e8 ("gemini: switch to 4.14") without
any explaination.

The image generation is disabled for now as it would break the build for
the target. The mkfwimage2 call need to be adjusted to reflect the real
size of kernel and rootfs. Nevertheless, add the required code to give
interested parties a chance to fix the remaining issues.

The dts would need to use the ecoscentric,redboot-fis-partitions
partition parser to get the correct partition offsets and size. It's
expected that the OEM firmware adjusts the on flash partition table with
the values defined in the image header.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:37 +01:00
Mathias Kresin
7055cb0acc gemini: fix alphabetical order
Reorder the image recipes to keep the alphabetical order.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:37 +01:00
Mathias Kresin
0013c94025 gemini: use dts compatible based image filenames
Use an output image filename based on the compatible string from the dts
files. This way it is way easier to get for which board an image is
intended.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:37 +01:00
Mathias Kresin
b9c6862d9d gemini: drop unnecessary image build default variables
They are either not required, set to an earlier set default value or
defined due to target features.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:37 +01:00
Mathias Kresin
7f17f3b418 gemini: drop unnecessary images
The root filesystem is already part of the factory image and most likely
not required at all.

The same applies to the kernel images.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:37 +01:00
Mathias Kresin
b010519f1e gemini: all images are factory images
There is no support for sysupgrade in gemini, hence all images are only
suitable for an installation via bootloader or oem firmware.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:37 +01:00
Mathias Kresin
10dab9b098 gemini: follow common pattern for temp dir naming
For temporary directories <imagename>.tmp is a common pattern in image
build code across the tree. Use it for the nas4220b/sq201 recipe as
well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:37 +01:00
Mathias Kresin
98c2261ac2 gemini: use existing build code where possible
Use the existing image build recipes in favour of introducing deplicate
shell code.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:36 +01:00
Mathias Kresin
1e606edce6 gemini: make all tar files more reproducible
Force a fixed sorting and use the parameters to create reproducible
archives for all tar invocations.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:36 +01:00
Mathias Kresin
6491643df4 gemini: build images in temporary directories
Create files in temporary directories within the build directory
instead manipulating files in the (final) output directory.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:36 +01:00
Mathias Kresin
0ffa6bae0a gemini: don't hardcode image filenames
Use the existing image build code mechanisms to specify the image output
filename.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:36 +01:00
Mathias Kresin
ec0d58ede4 gemini: fix parallel build
Due to the missing PROFILES all images are build, regardless of the
selected (or currently processed in case of a multi profile build).

Because of the race condition builds with eight parallel jobs fail,
which can be seen on the build bots as well.

Add the PROFILES variable for now, till the root cause is identified.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-26 15:23:36 +01:00
Tomasz Maciej Nowak
650df59e8a mvebu: remove default profile
When using Image Builder and building image for Cortex A53 or
A72 subtargets, it'll fail with following message:

Collected errors:
 * opkg_install_cmd: Cannot install package mwlwifi-firmware-88w8864.
 * opkg_install_cmd: Cannot install package mwlwifi-firmware-88w8964.
make[2]: *** [Makefile:153: package_install] Error 255
make[1]: *** [Makefile:114: _call_image] Error 2

This is beacuse both packages are available only for Cortex A9 subtarget
and are included in PACKAGES array in default profile. Instead patching
this, let's remove profiles completely, since all necessary packages are
specified in DEVICE_PACKAGES array for each device.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-01-26 10:45:34 +01:00
David Bauer
25eb02ae8e ipq40xx: remove misplaced MR33 UCI definition
This removes the misplaced UCI-network configuration for the MR33. The
LAN port is set in 01_leds while it is already correctly defined in
02_network.

This was most likely an oversight as no network configuration belongs
into 01_leds.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 10:45:34 +01:00
Robert Resch
53c25fa2c4 lantiq: Add support for 2nd USB port on Fritz!Box 7320 and 7330
Enable support for 2nd USB port, which is available on Fritz!Box 7320
and 7330. It was run-tested on 7320 and 7330 as well.

Signed-off-by: Robert Resch <openwrt@webnmail.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-01-26 10:42:19 +01:00
David Bauer
d4ba7bab25 lantiq: make AVM FRITZ!Box naming consistent
This commit changes the model string and device title of all AVM boards
to fit the naming of the manufacturer.

Drop all provider-specific titles as they are re-used for every device
generation by 1&1. The original AVM model name is printed on the bottom
of every devices.

Exception applies for boards which are only supported by a specific
sub-revision.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 10:41:26 +01:00
David Bauer
915fbd4e31 ramips: adjust Netgear R6120 model name
Adjust the model string and device title to match other Netgear routers
in the ramips target.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 10:41:03 +01:00
Jeff Kletsky
ee3120a9db ath79: fix GL.iNet AR300M family GPIOs/LEDs
Change the "status" LED to proper GPIO 12 and "red" naming.

Remove GPIO 2 from definition as a USB LED.

GPIO 2 is used to control power to the USB socket, not an LED.
As such, PWM on the line or typical LED triggers are inappropriate.

Users who wish to control the USB power for custom applications
can manipulate the GPIO through code, or for example, export it
through /sys/class/gpio/export.

Runtime-tested:  GL.iNet AR300M-Lite

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-01-26 10:40:06 +01:00
Jo-Philipp Wich
f01044e85c kernel: fix sdhci-msm build error
A missing upstream stable backport leads to the following build error:

     CC      drivers/mmc/host/sdhci-msm.o
    drivers/mmc/host/sdhci-msm.c:1158:3: error: 'const struct sdhci_ops' has no member named 'write_w'
      .write_w = sdhci_msm_write_w,
       ^~~~~~~
    drivers/mmc/host/sdhci-msm.c:1158:13: warning: excess elements in struct initializer
      .write_w = sdhci_msm_write_w,
                 ^~~~~~~~~~~~~~~~~
    drivers/mmc/host/sdhci-msm.c:1158:13: note: (near initialization for 'sdhci_msm_ops')
    scripts/Makefile.build:326: recipe for target 'drivers/mmc/host/sdhci-msm.o' failed

Solve the issue by backporting commit
99d570da30 ("mmc: Kconfig: Enable CONFIG_MMC_SDHCI_IO_ACCESSORS")
from linux-stable.

Ref: 528508ae8b (commitcomment-32049231)
Fixes: 528508ae8b ("kernel: bump 4.14 to 4.14.95")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-01-25 09:23:33 +01:00
Christian Lamparter
5bac623895 gemini: unify and fix ib-nas4220b and sq201 image creation
Both Build/sq201-images and Build/nas4220b-images scripts
are very similar. This patch unifies both methods at the
cost of renaming the produced sysupgrade file names, but
with the benifit of creating better reproducible files.

The patch also fixes a race in parallel builds in which case
the ImageInfo of one device could end up in both sysupgrade
files.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-24 15:53:04 +01:00
Christian Lamparter
de07a0a29a gemini: lazy set IMAGE_NAME
Currently, IMAGE_NAME is expanded at declaration time
and this causes strange filename in the builder's logs:

|cp: cannot stat '[...]/openwrt-gemini-dlink-dns-313-.': No such file or directory
|cp: cannot stat '[...]/openwrt-gemini-nas4220b-.': No such file or directory
|[...]

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-24 15:53:04 +01:00
Petr Štetiar
71cf3eab25 layerscape: dts: Unify naming of gpio-keys nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-01-24 15:53:04 +01:00
Petr Štetiar
9292822023 oxnas: dts: Unify naming of gpio-led nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-01-24 15:53:04 +01:00
Petr Štetiar
4a954e8620 oxnas: dts: Unify naming of gpio-keys nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-01-24 15:53:03 +01:00
Christian Lamparter
b5f6ede3c4 kernel: 4.19: use upstream usbport led trigger fix
This patch replaces the current hack with a better
version of the RFC patch has been accepted upstream.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-24 15:53:03 +01:00
Petr Štetiar
6928d06a7e ipq806x: dts: Unify naming of gpio-led nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-01-24 15:53:03 +01:00
Petr Štetiar
93c30bef7c ipq806x: dts: Unify naming of gpio-keys nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-01-24 15:53:03 +01:00
Petr Štetiar
540a7d1ecc ipq40xx: dts: Unify naming of gpio-led nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-01-24 15:53:03 +01:00
Petr Štetiar
98c6c8cdfe ipq40xx: dts: Unify naming of gpio-keys nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-01-24 15:53:03 +01:00
Christian Lamparter
f932137385 apm821xx: dts overhaul
- remove stray #address-cells / #size-cells

 - fix partition unit-addresses in wd-mybooklive.dts

 - remove index from MBL's gpio node name

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-24 15:53:03 +01:00
Petr Štetiar
cbb44f6ed7 apm821xx: dts: Unify naming of gpio-led nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-01-24 15:53:03 +01:00
Petr Štetiar
a692eecda1 apm821xx: dts: Unify naming of gpio-keys nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-01-24 15:53:03 +01:00
Petr Štetiar
87dcf24548 at91: dts: Unify naming of gpio-keys nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-01-24 15:53:02 +01:00
Christian Lamparter
1aa00f9d13 brcm2708: boot-part feature integration
This patch adds the boot-part feature which enables the brcm2708
target move from the custom boot partition size config option to
the generic CONFIG_TARGET_KERNEL_PARTSIZE.

Note:
For people using custom images: Just like with
CONFIG_TARGET_ROOTFS_PARTSIZE changing the value
can cause sysupgrade to repartition the device!
Make sure to have a backup in this case.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-24 15:53:02 +01:00
Koen Vandeputte
528508ae8b kernel: bump 4.14 to 4.14.95
Refreshed all patches.

Removed superseded patches:
- 0400-Revert-MIPS-smp-mt-Use-CPU-interrupt-controller-IPI-.patch

Compile-tested on: ar71xx, cns3xxx, imx6, lantiq (xrx200, AVM 3370), x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, lantiq (xrx200, AVM 3370)

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Mathias Kresin <dev@kresin.me>
Tested-by: Robert Resch <openwrt@webnmail.de>
2019-01-24 10:10:45 +01:00
HsiuWen Yen
fe7d965ea9 ramips: fix two-way hash and auto ageout on MT7621
Current code directly writes the FOE entry to hash_val+1 position
when hash collision occurs. However, it is found that this behavior
will cause the cache and the hardware FOE table to be inconsistent.

For example, there are three flows, and their hashed values are all
equal to 100. The first flow is written to the position of 100. The
second flow is written to the position of 100+1. Then, the logic of
the current code will also write the third flow to 100+1.

At this time, the cache has flow 1 and 2; and the hardware FOE table
has flow 1 and 3, where these two parts store different contents.
So it is necessary to check whether the hash_val+1 is also occupied
before writing. If hash_val+1 is also occupied, we won’t bind th
third flow to the FOE table.

Addition to that, we also cancel the processing of foe_entry removal
because the hardware has auto age-out ability. The hardware will
periodically iterate through the FOE table to find out the time-out
entry and set it as INVALID.

Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
2019-01-23 09:27:30 +01:00
Sebastian Kemper
69dfdda157 ath79: fix port order for dir 825-c1 and 835-a1
LAN ports 1 and 4 and 2 and 3 are interchanged. Fix this in 02_network
so the ports show up in the correct order in luci.

The correct ucidef_add_switch line is already present. This commit moves
the blocks around to keep alphabetical order.

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
2019-01-22 09:05:59 +01:00
Milan Krstic
39ede7bc67 ar71xx: ag71xx: preserve port mirror flags during swconfig apply
The swconfig load operation always triggers 'apply' function which in
this driver currently clears port mirroring flags effectively undoing
port mirroring configuration.

This fix preserves port mirroring flags during apply.

Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
2019-01-22 09:05:59 +01:00
Milan Krstic
76a629ee35 ath79: ag71xx: preserve port mirror flags during swconfig apply
The swconfig load operation always triggers 'apply' function which in
this driver currently clears port mirroring flags effectively undoing
port mirroring configuration.

Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
2019-01-22 09:05:59 +01:00
Hao Dong
62dadcb86c bcm53xx: add support for Phicomm K3
Hardware specifications:

- CPU: Broadcom BCM4709C0 @1.4GHz (Dual-Core ARM)
- RAM: 512 MB (DDR3)
- Flash: 128 MB (NAND)
- LAN ports: 3, LAN speed: 10/100/1000
- WAN ports: 1, WAN speed: 10/100/1000
- 2.4G: BCM4366 4x4 MIMO 1000Mbps -- Skyworks SE2623L 2.4GHz Power Amplifier (x4)
- 5G: BCM4366 4x4 MIMO 2167Mbps -- RFMD RFPA5542 5GHz Power Amplifier Module (x4)
- USB: 1x USB 3.0 port
- 1x LED, 1x reset button, 1x power switch
- 1x system status touch screen

Flash:

- Enter CFE
- Upload the trx file
- Reboot

Signed-off-by: Hao Dong <halbertdong@gmail.com>
2019-01-20 23:34:44 +01:00
Kevin Darbyshire-Bryant
1fdb4a7907 kernel: N_BADCLASS: fix macro to actually work - class e support
Backport upstream patch:

Commit 65cab850f0ee ("net: Allow class-e address assignment via ifconfig
ioctl") modified the IN_BADCLASS macro a bit, but unfortunatly one too
many '(' characters were added to the line, making any code that used
it, not build properly.

Also, the macro now compares an unsigned with a signed value, which
isn't ok, so fix that up by making both types match properly.

Reported-by: Christopher Ferris <cferris@google.com>
Fixes: 65cab850f0ee ("net: Allow class-e address assignment via ifconfig ioctl")
Cc: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2019-01-19 20:45:49 +00:00
Mathias Kresin
f5e61350e7 ramips: fix firmware splitter for edimax based boards
Use the correct splitter for board with the edimax header.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-19 12:51:04 +01:00
Mathias Kresin
116d0f276d kernel: add DT binding support to the Edimax uImage parser
It allows specifying those parsers directly in the DT.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-19 12:51:04 +01:00
Stijn Tintel
59e62809e6 kernel: remove upstreamed patch from 4.19
This patch applies cleanly, so it doesn't cause errors while rebasing
patches. It results in redifinition of inode_still_linked, causing build
to fail when ubifs is enabled. Drop the patch.

Fixes: a37098a2d0 ("kernel: bump 4.19 to 4.19.16")
Reported-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-01-17 10:45:31 +02:00
Stijn Tintel
f4ebd1ead0 kernel: drop old symbol from 4.19
CONFIG_LIRC_STAGING was removed in kernel 4.16.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-01-17 03:09:47 +02:00
Stijn Tintel
a37098a2d0 kernel: bump 4.19 to 4.19.16
Refresh patches.
Remove upstreamed patches:
- backport/096-mips-math-emu-Write-protect-delay-slot-emulation-pages.patch
- backport/096-v4.20-netfilter-ipv6-Preserve-link-scope-traffic-original-.patch
- backport/424-v4.20-net-dsa-fix-88e6060-roaming.patch
- hack/100-mtd-rawnand-qcom-fix-memory-corruption-that-causes-p.patch
- pending/510-f2fs-fix-sanity_check_raw_super-on-big-endian-machines.patch
Update patch that no longer applies:
- backport/343-netfilter-nft_flow_offload-handle-netdevice-events-f.patch

Compile-tested: mesongx
Runtime-tested: mesongx

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-01-17 03:04:13 +02:00
Koen Vandeputte
63a2ed3ba5 kernel: bump 4.9 to 4.9.150
Refreshed all patches.

Remove upstreamed:
- 096-mips-math-emu-Write-protect-delay-slot-emulation-pages.patch

Altered patches:
- 024-7-net-reorganize-struct-sock-for-better-data-locality.patch

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-16 12:56:30 +01:00
Koen Vandeputte
5be22ef2fa kernel: bump 3.18 to 3.18.132
Refreshed all patches.

Compile-tested: adm5120
Runtime-tested: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-16 12:56:30 +01:00
Mathias Kresin
26a016731d firmware-utils: mksercommfw: overhaul image creation
Move the zip compression into a build recipe. Pad the image using the
existing build recipes as well to remove duplicate functionality

Change the code to append header and footer in two steps. Allow to use a
fixed filename as the netgear update image does.

Use a fixed timestamp within the zip archive to make the images
reproducible.

Due to the changes we are now compatible to the gnu89 c standard used by
default on the buildbots and we don't need to force a more recent
standard anymore.

Beside all changes, the footer still looks wrong in compare to the
netgear update image.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-15 19:11:54 +01:00
Stijn Tintel
8c6f00ef4f kernel: bump 4.14 to 4.14.93
Refresh patches.
Remove upstreamed patches:
- backport/096-mips-math-emu-Write-protect-delay-slot-emulation-pages.patch
- pending/510-f2fs-fix-sanity_check_raw_super-on-big-endian-machines.patch
- brcm2708/950-0415-qmi_wwan-apply-SET_DTR-quirk-to-the-SIMCOM-shared-de.patch

Compile-tested: ar71xx, ath79, brcm2708/bcm27{08,10}, octeon, x86/64
Runtime-tested: ar71xx, ath79, brcm2708/bcm27{08,10}, octeon, x86/64

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-01-14 02:20:40 +02:00
Hauke Mehrtens
900c6b1a42 sunxi: Add support for kernel 4.19
This adds supprot for kernel 4.19 to the sunxi target. The patches and
the configuration were copied from the kernel 4.14 patches folder and
adapted for kernel 4.19.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 17:35:14 +01:00
Hauke Mehrtens
2eeb5d6aac sunxi: Refresh kernel 4.14 configuration
Refresh the sunxi kernel configuration without doing any intentional
changes.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 17:35:14 +01:00
Hauke Mehrtens
0057beab1b sunxi: Use kernel specific sub target configuration
To make it easier to support multiple kernel versions in parallel also
copy the sub target specific kernel configurations into kernel specific
files.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 17:20:07 +01:00
Hauke Mehrtens
48f81ee1d0 sunxi: Remove unneeded patches
In the device tree file the higher offsets of the reset controller are
not used, so this patch supporting higher bits is not needed.
The sunxi architecture switched to the simple reset controller with
kernel 4.19 and then this patch does not apply any more.
The sunxi target in OpenWrt is very close to mainline, so if the device
tree files from the mainline Linux kernel need this the mainline kernel
will get support for this.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 17:20:07 +01:00
Hauke Mehrtens
cfc9bde379 kernel/modules: Add missing config option
This configuration option was added in kernel 4.15 and is missing in the
kernel 4.19 configuration.

Fixes: ed2839ac41 ("kernel/modules: add kmod-pmbus-zl6100 module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 17:20:07 +01:00
Hauke Mehrtens
403d36ef3d malta: Add support for kernel 4.19
This adds a kernel configuration file for kernel 4.19 on malta.
CONFIG_POWER_RESET_PIIX4_POWEROFF and CONFIG_POWER_RESET_SYSCON were
activated because malta now uses this driver for reboot.

CONFIG_BLK_DEV_SR was also added because it was also added to the kernel
default configuration.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 16:31:40 +01:00
Hauke Mehrtens
4ab689c137 malta: Refresh kernel 4.14 configuration
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 16:31:38 +01:00
Hauke Mehrtens
c54e4747be kernel: MIPS: Add CPU option reporting to /proc/cpuinfo
Many MIPS CPUs have optional CPU features which are not activates for
all CPU cores. Print the CPU options which are implemented in the core
in /proc/cpuinfo. This makes it possible to see what features are
supported and which are not supported. This should cover all standard
MIPS extensions, before it only printed information about the main MIPS
ASEs.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 16:24:50 +01:00
Hauke Mehrtens
c7102a7699 kernel/modules: Fix build of kmod-pmbus
This fixes two build problems introduced with the recently added new
kernel module package.

Fixes: ed2839ac41 ("kernel/modules: add kmod-pmbus-zl6100 module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 13:16:02 +01:00
Chuanhong Guo
bd03255ec4 generic: ar8216: ar8327: kill warnings
This fixed warnings caused by returning value in a void function

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-01-13 12:25:30 +01:00
David Bauer
97e4311fca mpc85xx: add support for Sophos RED 15w Rev.1
Hardware
========
CPU:  Freescale P1010 PowerPC
RAM:  128M DDR3
NAND: 128MiB
ETH:  RTL8211F SGMII PHY
      RTL8367B 5-port RGMII switch
      (not connected to SoC - unmanaged)
WiFi: SparkLan WPEA-121N
       - Atheros AR9382 2T2R abgn
USB:  1x USB 2.0
LED:  System, Router, Internet, Tunnel controllable
      LAN1-4, WAN, Power non-controllable
BTN:  None

Installation
============
1. Power on the device while attached to the Console port.

2. Halt the U-Boot by pressing Enter when prompted.

3. Set the correct bootcmd for booting OpenWRT:
 > setenv bootargs_owrt "setenv bootargs console=ttyS0,115200"
 > setenv bootcmd "run bootargs_owrt;
   nand read 0x1000000 0x300000 0x800000;
   bootm 0x1000000;"
 > saveenv

5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a
   TFTP server root-directory served on 192.168.1.2/24. Connect your
   computer to one of the LAN-ports.

4. Boot OpenWRT initramfs image with
 > run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin;
   bootm 0x1000000;

6. (Optional)
   Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case
   you ever want to go back to the vendor firmware.

7. Create Ubi Volume on mtd4 by executing
 > ubiformat /dev/mtd4 -y

8. Transfer OpenWRT sysupgrade image to the device via SCP and install it
   with
 > sysupgrade -n <openwrt-image-file>

Back to Stock
=============
If you want to go back to the stock firmware, here is the bootcmd of the
vendor firmware:
 > setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5;
   nand read 0xc00000 0x00300000  0x100000;
   nand read 0x1000000 0x00400000 0x00800000;
   bootm 0x1000000 - 0xc00000

Set it via 'setenv' from the U-Boot shell and don't forget to save it
using 'saveenv'!

After this, boot the OpenWRT initramfs image just like you would for
installation. Write back the three vendor partitions using mtd. Reboot
the device afterwards.

Signed-off-by: David Bauer <mail@david-bauer.net>
[refresh and reorder patches]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-13 11:31:43 +01:00
Christian Lamparter
85be0f4c21 apm821xx: 4.14: sync config
This patch syncs the 4.14 kernel config to the
current generic configuration.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-13 11:31:43 +01:00
Pawel Dembicki
46d4c09bb6 mpc85xx: disable initramfs image in TL-WDR4900
Initramfs image isn't required for this device and regular
initramfs generation isn't work properly. It create not working
binaries.

This patch disable initramfs image for TL-WDR4900.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-01-13 11:31:43 +01:00
Pawel Dembicki
5de6aed42c mpc85xx: add support for Freescale (NXP) P2020RDB
This commit add initial support for Freescale (NXP) P2020RDB

Hardware:
SoC: P2020 2x1GHz
DRAM: 512-1GB DDR3
2 + 4 GBE (2 separate ports and four in VSC7385)
Flash: 16MB NOR, 32MB NAND, 16MB SPI-NOR
PCIE x1 and mPCIE x1
SD Reader

Interfaces:
GBE RJ45 x6
USB2.0 x1
UART x2
I2C x2
JTAG x1
SD x1
PCIE x2 (PCIE and mPCIE)

Flash instructions:
Place sysupgrade image to 0x80000 address in NOR.
Eg. (no brakelines in setenv command):

setenv 'firmware_flash tftpboot $loadaddr $firmwarefile;
 protect off $norfdtaddr +$filesize; erase $norfdtaddr +$filesize;
 cp.b $loadaddr $norfdtaddr $filesize; protect on $norfdtaddr +$filesize;
 cmp.b $loadaddr $norfdtaddr $filesize'
setenv firmwarefile firmware.bin
run firmware_flash

Boot (no brakeline in setenv command):
setenv bootcmd 'setenv bootargs root=/dev/mtdblock3 rw console=$consoledev,
$baudrate rootfstype=squashfs $othbootargs;
bootm $norfdtaddr'
saveenv
boot

Known issues:
-Switch is unmanaged (VSC 7385 is connected via eLBC, driver uses SPI)
-No SD reader support

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [refreshed patches]
2019-01-13 11:31:43 +01:00
Pawel Dembicki
ed2839ac41 kernel/modules: add kmod-pmbus-zl6100 module
This patch adds the kmod packaging for the Intersil / Zilker Labs
ZL6100 and compatible digital DC-DC controllers as well as the
core kernel module for the Power Management Bus.

Add:
kmod-pmbus-core
kmod-pmbus-zl6100

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-01-13 11:07:37 +01:00
Hauke Mehrtens
75fdf3ba01 x86: Add support for kernel 4.19
This adds initial support for kernel 4.19 to the x86 target.
The patches and the kernel configurations were copied from kernel 4.14
and then refreshed.

The legacy and the genode target will not support PAE any more because
they use a CPU type which does not support PAE, the generic sub target
still supports PAE.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-12 22:40:36 +01:00
Hauke Mehrtens
f6e0ecdceb x86: Refresh kernel 4.14 configuration
This refreshes the kernel configuration for kernel 4.14.
First this was run for the legacy target:
	make kernel_oldconfig
Then for all targets including the legacy target this was run:
	make kernel_oldconfig CONFIG_TARGET=subtarget
The option CONFIG_104_QUAD_8 was added to the generic configuration
because it would have been automatically removed.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-12 22:40:12 +01:00
Hauke Mehrtens
0ea7160abe x86: Use kernel specific subtarget configurations
This makes it possible to use different sub target configurations for
kernel 4.19 for example.
To support kernel 4.9 and kernel 4.14 with the same configuration file
already needed some extra work this will not be needed for kernel 4.19
any more.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-12 22:39:41 +01:00
Hans Dedecker
4bd9d331e5 octeon: fix typo in platform.sh
Fix upgrade typo

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2019-01-12 19:40:13 +01:00
Rafał Miłecki
45ce9897c0 kernel: add bcma fix for subdevices DMA parameters
This fixes bgmac DMA allocations with kernel 4.19.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-01-11 07:33:56 +01:00
Rafał Miłecki
34696ce25e kernel: backport bcma patches that improve printing functions
Updated printing functions use dev_* helpers to provide more meaningful
messages.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-01-10 16:47:43 +01:00
Rafał Miłecki
7175b1356e brcm47xx: backport MIPS fix adding struct device for the SoC
It's needed to:
1) Fix GPIOLIB_IRQCHIP as in 4.19 there is no bcma revert anymore
2) Fix /sys/devices/
3) Fix dma_zalloc_coherent() regression

It still needs a bcma change that will follow later.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-01-10 06:57:19 +01:00
Rafał Miłecki
94561333cd brcm47xx: backport a final/accepted Netgear WNDR3400v3 patch
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-01-10 06:35:57 +01:00
Koen Vandeputte
630d8b87a5 cns3xxx: use actual size reads for PCIe
upstream commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
reimplemented cns3xxx_pci_read_config() using pci_generic_config_read32(),
which preserved the property of only doing 32-bit reads.

It also replaced cns3xxx_pci_write_config() with pci_generic_config_write(),
so it changed writes from always being 32 bits to being the actual size,
which works just fine.

Due to:
- The documentation does not mention that only 32 bit access is allowed.
- Writes are already executed using the actual size
- Extensive testing shows that 8b, 16b and 32b reads work as intended

It makes perfectly sense to also swap 32 bit reading in favor of actual size.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-07 17:09:06 +01:00
Koen Vandeputte
f56a4e809b kernel: bump 4.14 to 4.14.91
Refreshed all patches.

Removed upstreamed:
- 500-ubifs-Handle-re-linking-of-inodes-correctly-while-re.patch

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-07 17:09:06 +01:00
Koen Vandeputte
30d518bf16 kernel: bump 4.9 to 4.9.148
Refreshed all patches.

Altered patches:
- 902-debloat_proc.patch

Removed upstreamed:
- 424-v4.20-net-dsa-fix-88e6060-roaming.patch

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-07 17:09:06 +01:00
Koen Vandeputte
a18f68ff30 kernel: bump 3.18 to 3.18.131
Refreshed all patches.

Altered patches:
- 902-debloat_proc.patch

Compile-tested on: adm5120
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-07 17:09:06 +01:00
John Crispin
93c35bfa21 ramips: whitespace cleanup inside hnat driver
Signed-off-by: John Crispin <john@phrozen.org>
2019-01-07 15:45:51 +01:00
HsiuWen Yen
6b9bdbd493 ramips: add two-way hashing scheme for MT7621
Sometimes the tuples might be hashed to the same FOE entry.
When this hash collision problem occurs, some of the
connections will not be bound and consequently the CPU
idle rate cannot reach 100%. Therefore, two-way hashing
is adopted to alleviate this problem.

Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
2019-01-07 15:40:51 +01:00
David Bauer
634c733065 ipq40xx: copy Fritz4040 UBoot to STAGING_DIR_IMAGE
Copy U-Boot to STAGING_DIR_IMAGE (and append it to the EVA-image from
there) to fix image generation using the image-builder.

Also remove the bootloader from DEVICE_PACKAGES and instead use the
BUILD_DEVICES directive from within the U-Boot makefile.

This fixes eva-image generation using the OpenWRT image-builder.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-06 12:26:12 +01:00
Christian Lamparter
bbe7ad5a2f mpc85xx: 4.19: refresh kernel config
This patch syncs the 4.19 kernel config to the
current generic configuration.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-05 23:36:39 +01:00
Christian Lamparter
32420fc6b9 mpc85xx: 4.14: refresh kernel config
This patch syncs the 4.14 kernel config to the
current generic configuration.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-05 23:36:39 +01:00
Robert Marko
bba1428274 ipq40xx: 4.14: Sync kernel config
This patch syncs the 4.14 kernel config to the
current generic configuration.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
2019-01-05 22:23:41 +01:00
Robert Marko
0c1f1dab59 ipq40xx: 4.19: Sync kernel config
This patch syncs the 4.19 kernel config since the
KERNEL_STACKPROTECTOR and compiler options are
now part of the 4.19 generic config.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
2019-01-05 22:23:41 +01:00
Christian Lamparter
32e953b821 ipq40xx: fix 4.14 ImageBuilder build woes
Robert Marko reported an issue with the current imagebuilder images:
"Imagebuilder includes the new kmod-usb-dwc3-qcom USB driver
package by default even on 4.14. [...] the current state imagebuilder
can't build images under 4.14 at all as the kmod-usb-dwc3-qcom does
not exist in it so it throws and error and exits."

This patch reverts the Makefile to just kmod-usb-dwc3-of-simple and
once the switch to 4.19 is done. It also removes the
kmod-usb-phy-qcom-dwc3 as they only contain the usb-phy drivers for
the ipq806x generation.

Dynamic switching based on the KERNEL_PATCHVER is possible by using:
   $(if $(filter 4.14,$(KERNEL_PATCHVER)),kmod-usb-dwc3-of-simple,kmod-usb-dwc3-qcom)
though it

Fixes: 13321fa142 ("ipq40xx: Use kmod-usb-dwc3-qcom by default")
Fixes: 6e58fb2c33 ("ipq40xx: kmod-usb-dwc3-of-simple vs kmod-usb-dwc3-qcom")
Reported-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-05 22:23:10 +01:00